EEPROM in the camera module does not require any specific power
resources. This will ensure that no unnecessary resources are turned on
while accessing the camera EEPROM.
BUG=b:167938257
TEST=Build and boot to OS in Drawlat. Ensure that the camera EEPROM is
listed in the output of i2cdetect.
Change-Id: Iece9b3f657bf94a21cc08bf1745353575858f9b2
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47230
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Update Power Limit2 (PL2) minimum value to the same as maximum value for
dedede variants (baseboard and drawcia). Currently, variants like boten,
waddledee, waddledoo, metaknight and wheelie uses the DTT entries from
baseboard devicetree since there is no override present for these variants.
So, these variants will also reflect this change of PL1 minimum value.
For madoo variant, PL2 minimum value already set the same as PL2 maximum
value. DTT does not throttle PL2, so this minimum value change here does not
impact any existing behavior on the system.
BUG=None
BRANCH=None
TEST=Build and test on drawcia system
Change-Id: I7ecf1ffcc7871192ebe18eb8c3c3fd3e1193721e
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47154
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
InternalGfx isn't used so drop it.
Change-Id: I12f424d8d883e065ef8d007e56a8bff41a7fae53
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47176
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Production Volteer devices have Cr50 TPM connected via SPI, depending on
Cr50 firmware version it may or may not support long enough interrupt
pulses for the SoC to safely be able to enable lowest power mode.
Some reworked Volteer devices have had the Cr50 (Haven) TPM replaced
with Dauntless, communicating via I2C. The I2C drivers do not support
being accessed early in ramstage, before chip init and memory
mapping, (tlcl_lib_init() will halt with an error finding the I2C
controller base address.)
Since the Dauntless device under development can be made to support
longer interrupts, or a completely new interrupt signalling mode, there
is no need to try to go through the same discovery as is done via SPI.
This CL will skip the discovery, enabling the S0i3.4 sleep mode in all
cases, on the reworked test devices.
BUG=b:169526865, b:172509545
TEST=abuild -t GOOGLE_VOLTEER2 -c max -x
Change-Id: I08a533cede30a3c0ab943938961dc7e4b572d4ce
Signed-off-by: Jes Bodi Klinke <jbk@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47049
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The current I2C3 bus frequency is 341 kHZ, which does not meet the spec.
This change updates scl_lcnt, scl_hcnt, sda_hold value for I2C3 to bring
the bus frequency closer to 400kHz.
BUG=b:153588771
TEST=Verified that I2C3 frequency is 394kHz.
Signed-off-by: Johnny Li <johnny_li@wistron.corp-partner.google.com>
Change-Id: Ie1ef95bb39d71fbb113120a0ec88305bc23e7ab9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47225
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
This setting copy from puff reference board
and should measure again after whole system build.
BUG=b:155261464
BRANCH=puff
TEST=emerge-puff coreboot and check system speaker has sound output.
Change-Id: Idd5c3276e9306e81ea766d14ed1415a68dedc2ad
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47161
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: Sam McNally <sammc@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Adjust USB2 phy si setting fine tune on DVT for Ezkinil.
BRANCH=zork
BUG=b:156315391
TEST=Measuring scope timing and test usb detection
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Change-Id: Id537b6e9a17f47481b6aedcea0c6a8474d993b6d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47011
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Since the mainboard Kconfig is sourced before the SoC one, it would
still be possible to override this setting at mainboard level, even
though that shouldn't be needed. The maximum CPU count for Picasso is 8,
since the chips have only up to 4 cores with up to two threads each.
Change-Id: I53449b8fa73c5d13e6ea77bee6eed8896b7d3ec3
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47205
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Move the `GWAK` method into the GPIO device, and have lpc.c include the
LP GPIO code. All usages of `GWAK` on mainboards need to be updated.
Change-Id: Id6a41f553d133f960de8b232205ed43b832a83d2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46775
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This CL is entirely generated by running the automatic formatter on this
one file.
BUG=None
TEST=abuild -t GOOGLE_VOLTEER2 -c max -x
Change-Id: Ibdd8cc2222e7af11c11df963b088ca2db07a3214
Signed-off-by: Jes Bodi Klinke <jbk@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47048
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Add the USB ports to the devicetree for describing them in ACPI,
including defining the port relationships and defining the reset
GPIO for the bluetooth device.
BUG=b:151731851
TEST=tested on volteer, all other boards were checked against the
latest available schematic.
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Change-Id: Ia1e5b71e7750a478ff79372c48616bbf5c21b79c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46853
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Define option value 6 for DB_USB where there is a Type-A port but
no Type-C port on the daughterboard.
BUG=b:151731851
TEST=build volteer boards
Change-Id: I489d24316556dedfecd821e502f1461010b1400f
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46906
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
variant_smi_sleep is called in smm stage so we need to add
variant.c into smm stage. Otherwise it will call the dummy one.
BUG=b:168075958
BRANCH=octopus
TEST=build image passed.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I41df1a30b119ab3e04f9ae01955b6044f137527f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46847
Reviewed-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Reviewed-by: Marco Chen <marcochen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
For development of the firmware to run on the Dauntless TPM, a number of
Volteer2 devices are being reworked to replace the H1 chip with probe
wires to connect to an external Dauntless development board.
Some modification to the AP firmware is required, not least because the
Dauntless chip is connected via I2C bus, instead of SPI. Most of the
Dauntless developers will not otherwise have a Chrome OS chroot.
Because of the above, I think it makes sense to have a new variant, for
the reworked devices, which I intend to create with this CL.
BUG=b:169526865
TEST=abuild -t GOOGLE_VOLTEER2_TI50 -c max -x
Change-Id: Ibdcd6c2ce3941c229518f21f0e479890b5d76dd1
Signed-off-by: Jes Bodi Klinke <jbk@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46437
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add supported memory parts in the mem_parts_used.txt and generate the
SPD ID for the parts. The memory part being added is:
MT53E512M32D2NP-046 WT:E
K4U6E3S4AA-MGCR
H9HCNNNBKMMLXR-NEE
MT53E1G32D2NP-046 WT:A
K4UBE3D4AA-MGCR
BUG=b:169813211
TEST=Build the metaknight board.
Signed-off-by: Tim Chen <tim-chen@quanta.corp-partner.google.com>
Change-Id: I0d0d22f4790f66b5265803e4dcf01234a16b1993
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46810
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Configure board specific DPTF parameters for delbin
BUG=b:168958222
BRANCH=volteer
TEST=build and verify by thermal team
Signed-off-by: Frank Chu <frank_chu@pegatron.corp-partner.google.com>
Change-Id: I69aa6046fdc90a2cf59ea3a13fdb15c8bc0d29a2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46676
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Create the voema variant of the volteer reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.2.0).
BUG=b:171755775
BRANCH=None
TEST=util/abuild/abuild -p none -t google/volteer -x -a
make sure the build includes GOOGLE_VOEMA
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I4e1872d1ebff6fefdfb232f1ff82fce95a1ec643
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47007
Reviewed-by: YH Lin <yueherngl@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add ELAN touch support and update Goodix settings.
BUG=b:157265632
BRANCH=zork
TEST=emerge coreboot and check both touch screen are workable.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Icfc2421061e8b3163d7d5108673351bc17df20ec
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46929
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
This change reorganizes the CNVi device entries in mainboard
devicetree/overridetree and SoC chipset tree to make it consistent
with how other SoC internal PCI devices are represented i.e. without a
chip driver around the SoC controller itself.
Before:
chip drivers/wifi/generic
register "wake" = "..."
device pci xx.y on end
end
After:
device pci xx.y on
chip drivers/wifi/generic
register "wake" = "..."
device generic 0 on end
end
end
Change-Id: I22660047a3afd5994400341de0ca461bbc0634e2
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46865
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Terrador and Todor are fanless design, so disable DPTF active policy.
BUG=b:171019363,b:170699797
BRANCH=volteer
TEST=build and verify by thermal team
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I53a33b8706d7a7d4013a2a5627a620223fcffc3e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46874
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
GPIO D4 was used for camera reset for both front and rear cameras
(RCAM_RST_L/FCAM_RST_L) in RIPTO. For later volteer versions,
GPIO F15 is dedicated to the rear camera reset (RCAM_RST_L).
Before, BOARD_GOOGLE_VOLTEER flag was used for setting the right
RCAM_RST_L per volteer version. However, we don't support RIPTO
anymore. Also using flags for different volteer version support can
be error-prone. Removing RIPTO support.
BUG=b:171726823
BRANCH=none
TEST=Build and boot volteer proto2 or later version. Camera should
work without an issue.
Signed-off-by: Daniel Kang <daniel.h.kang@intel.com>
Change-Id: I961fc17092887b4807c12c95f7139bb7e7b33e91
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46826
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
LTE module Fibocom L850-GL is lost after idle overnight,
with this workaround, host will not initiate U3 wakeup
at the same time with device, which will avoid the race condition.
If this option is set in the devicetree, the bits[7:4] in XHCI MMIO BAR +
offset 0x80A4 (PMCTRL_REG) will be updated from default 9 to 0.
BUG=b:169645448
BRANCH=octopus
TEST=build coreboot with DisableXhciLfpsPM being set to 1 and flash
the image to the device. Run following command to check if
bits[7:4] is set 0:
>iotools mmio_read32 "XHCI MMIO BAR + 0x80A4"
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I3a04320b0e2441dce540a5afdc461f12de45c41b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46868
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
We all knew this was coming, 32 bits is never enough. Doing this early
so that it doesn't affect too much code yet. Take care of every usage of
fw_config throughout the codebase so the conversion is all done at once.
BUG=b:169668368
TEST=Hacked up this code to OR 0x1_000_0000 with CBI-sourced FW_CONFIG
and verify the console print contained that bit.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: I6f2065d347eafa0ef7b346caeabdc3b626402092
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45939
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Now that soc_get_pmc_mux_device() is gone, the PMC MUX connector devices
can be hooked up together via devicetree aliases.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Ib51764da5b3c029f9ac7ac60199a0aedfc7f29b1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45878
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The current I2C5 bus frequency is 367 kHZ, which does not meet the spec.
This change updates scl_lcnt, scl_hcnt, scl_hcnt value for I2C5 to bring
the bus frequency closer to 400kHz.
BUG=b:153588771
TEST=Verified that I2C5 frequency is between 389-396kHz.
Signed-off-by: Johnny Li <johnny_li@wistron.corp-partner.google.com>
Change-Id: If0803a74ba9071acf15486ce4038261c1681a92f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46142
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Flesh out the PCH configuration into a separate chip. Keep it within the
Broadwell SoC directory for now, to ease moving files around. The boards
were prepared beforehand and the devicetrees require next to no changes.
Tested on out-of-tree Acer Aspire E5-573, still boots.
Change-Id: I28d948f3e6d85e669d12b29516d867c1d1ae9e1a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46700
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
`chip` entries are only hooked up via device nodes to the tree. A `chip`
without a `device` below it does nothing. To allow variants to override
SATA tuning parameters, ensure a device exists under the PCH chip scope.
Without this change, some variants would not properly override the SATA
tuning parameters after extracting the PCH parts into a different chip.
TEST=Sanity-check static.c and verify overridetrees override properly.
Change-Id: I013dbe1403567b93c8ee0e66f76481f2a3f42796
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46769
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Create the ambassador variant of the puff reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.2.0).
BUG=b:171561514
BRANCH=None
TEST=util/abuild/abuild -p none -t google/hatch -x -a
make sure the build includes GOOGLE_AMBASSADOR
Signed-off-by: Matt Ziegelbaum <ziegs@chromium.org>
Change-Id: Ib0e3a813a120a4a8e984f3a89dc3ba100d94da95
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46829
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Remove code to turn on backlight during ACPI mode because backlight has
been properly enabled in ACPI.
BUG=b:158087989
BRANCH=Zork
TEST=tested backlight during reboot and suspend
Signed-off-by: Josie Nordrum <JosieNordrum@google.com>
Change-Id: I3bf06042aa19e4559127d611d401f0ba0516b3a6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46823
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add internal pull-down for GPP_D19 to improve DMIC noise issue on
nightfury.
BUG=b:171669255
BRANCH=firmware-hatch-12672.B
TEST=Built and checked GPP_D19 voltage after booting
Change-Id: Ie63f260be3d6a55f91908db59312b3b0a8af98f4
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46816
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Bob Moragues <moragues@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
To support gpio reset SoC, we need to pass the reset gpio parameter to
BL31.
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Change-Id: I2ae7684a61af76693605cc0bcf8d20c8992c7bff
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46388
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The pins for SD and MMC must be configured properly
so we can access them in payloads.
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Change-Id: Ie6bdffb987d5acf286645550f1c53f294f71c38a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46685
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
LTE module Fibocom L850-GL is lost after idle overnight,
with this workaround, host will not initiate U3 wakeup
at the same time with device, which will avoid the race condition.
If this option is set in the devicetree, the bits[7:4] in XHCI MMIO BAR +
offset 0x80A4 (PMCTRL_REG) will be updated from default 9 to 0.
BUG=b:171478764
BRANCH=octopus
TEST=build coreboot with DisableXhciLfpsPM being set to 1 and flash
the image to the device. Run following command to check if
bits[7:4] is set 0:
>iotools mmio_read32 "XHCI MMIO BAR + 0x80A4"
Change-Id: I213fed2b56f216747b2727b69f97d46d8c0c872e
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46701
Reviewed-by: Marco Chen <marcochen@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
invoke LTE power off function to meet LTE power sequence while DUT is
in reboot state.
BUG=b:167565015
BRANCH=octopus
TEST=build and verify on the DUT with LTE
Change-Id: I825cefb524ddaf9a9cb6add31c2ee0eea484f978
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46022
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Henry Sun <henrysun@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Configure the I2C bus high and low time for all enabled I2C buses.
BUG=b:168783630
TEST=Measured the I2C bus frequency reduce to 387 KHz.
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Change-Id: I9f5b81815f86db7bdcea95a95b9c9b235b4a34b1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46613
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The LCM ID is not really used on Jacuzzi followers and the reference
design expects ADC to return 0. However, there were hardware design
issues so the returned value became unexpected numbers.
- Juniper and Kappa returns 1.
- Burnet and Esche returns 1 on normal boot, and 0 on recovery boot.
- Cerise and Stern usually returns 0, and sometimes 1.
To fix that, we are changing LCM ID to fixed value for Jacuzzi followers.
BUG=b:170916885,b:171365301
BRANCH=kukui
TEST=1. emerge-jacuzzi coreboot
2. check burnet/esche skuid correctly
Change-Id: I3b43b9153315ec65e9168c4e84ea844dff14d446
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46442
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
1. Enable dptf feature and remove fan control part from overridetree.cb
2. Update tcc offset to 5
3. Follow thermal validation and update PL2 max_power to 51
BUG=b:167931578, b:170357248
Signed-off-by: Nick Chen <nick_xr_chen@wistron.corp-partner.google.com>
Change-Id: I99e429b90ed7de08385fe51ca742865b1266eef9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45860
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This reverts commit 214c719eed.
CB:45857 overrides the GPIO PM configuration if Cr50 does not support
long interrupt pulse width. More recent Cr50 Firmware versions support
long pulse width and hence the GPIO PM can take the default
configuration.
BUG=None
TEST=Build and boot Drawlat to OS. Ensured that 200 iterations of
suspend/resume sequence, warm and cold reboot cycles each are
successful.
Change-Id: I8e3be42cd82fd3ae919d23d6f19c84a90b9c737a
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46652
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
The dt option `speed_shift_enable` is obsolete now. Drop it.
Change-Id: I5ac3b8efe37aedd442962234478fcdce675bf105
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46462
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Enable front camera power in ramstage.
BUG=b:169170677
BRANCH=volteer
TEST="emerge-volteer coreboot" compiles successfully.
Signed-off-by: Pan Sheng-Liang <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: I8b5a9a8333ed518883aa3664a115a4ba2e8a0218
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46618
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: YH Lin <yueherngl@google.com>
New SKU ID 5 is used for LTE touch SKU. This patch does LTE power off
for LTE sku and only use Wifi SAR table for non-LTE sku.
BUG=b:168001586
BRANCH=octopus
TEST=Check no SAR table can be loaded with sku id 4 and 5.
Change-Id: Ic0405d3e52aa813bbb1f350966a9e2825e595ce4
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46643
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Since google_chromeec_cbi_get_board_version and google_chromeec_cbi_get_fw_config both call cbi_get_unit32 and return 0 as success, non-zero as failure. Let's add more readability for the false condition.
BUG=None
TEST=check with empty CBI value
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: Ia49ac1ee35302f8f6afe8c0eb8e13afdf36c5b2b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46566
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
According to the schematic, SRCCLKREQ1# is not connected, so disable it
for terrador and todor.
BUG=b:171278849
BRANCH=volteer
TEST="emerge-volteer coreboot" compiles successfully.
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I5f7734d64390bfadbdb8d152261103adb8e75f40
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46592
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sheng-Liang Pan <sheng-liang.pan@quanta.corp-partner.google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
According to the schematic,SRCCLKREQ1# is not connected,so disable it
on voxel.
BUG=b:171279034
BRANCH=volteer
TEST="emerge-volteer coreboot" compiles successfully.
Signed-off-by: Pan Sheng-Liang <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: Ibc4f766bd737f30a9ac3c7354d54398e0c36d59d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46612
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The Asurada EC is using the large packet (256B) mode, and we were
seeing lots of timeout errors on various commands.
The AcceptTimeoutUs in EC SPI driver is hard-coded at 5000,
and that is too small for large packet running in 1M so we
should change EC SPI to the same value that kernel is using (3M).
BUG=b:161509047
TEST=emerge-asurada coreboot chromeos-bootimage; flash and boot
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Change-Id: I9c47324022129ca23ef75d0c80e215da1692636d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46394
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enhance USB 2.0 C0/C1 A0/A1 SI by increasing the level of
"HS DC Voltage Level" and " Disconnect Threshold Adjustment" registers.
COMPDISTUNE0: 0x3->0x7
TXVREFTUNE0: 0x6->0xf
BUG=b:166398726
BRANCH=zork
TEST=1. emerge-zork coreboot
2. check U2 register is set correctly.
3. U2 SI all pass
Change-Id: I69d942605c6d43ece0d71f67df3a5e00b998219b
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46545
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Update the two load line slope settings for the SVID3 telemetry.
AGESA sends these values to the SMU, which accepts them as units
of current. Proper calibration is determined by the AMD SDLE tool
and the Stardust test.
VDD Slope: 62852 -> 62641
SOC Slope: 28022 -> 28333
BUG=b:170531252
BRANCH=zork
TEST=1. emerge-zork coreboot
2. pass AMD SDLE/Stardust test
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Change-Id: Id831907aa47be27fef2e33bb884a1118ffec14a0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46655
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
The disconnect voltage needs to be adjusted up because the HS DC voltage
level is 0xF.
BUG=b:170879690
TEST=Servo_v4 USB hub functions
BRANCH=zork
Change-Id: If8662015a45c57e457b4593e55af888084842f58
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46601
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
RW_LEGACY region needs to be 1 MiB to accommodate any alternate
firmware. Hence update the flash ROM layout as below:
* Grab ~512 KiB from each FW_MAIN_A/B regions and allocate them to
RW_LEGACY region so that it grows to 1 MiB.
* Remove VBLOCK_DEV region which is not used.
* Re-size the ELOG region to 4 KiB since that is the maximum size of the
ELOG mirror buffer.
* Resize RW_NVRAM, VBLOCK_A/B regions to 8 KiB since no more than that
size is used in those regions.
* Resize SHARED_DATA region to 4 KiB since no more than that size is
used in that region.
* Based on the resizing, allocate each FW_MAIN_A/B regions with 72 KiB.
BUG=b:167943992, b:167498108
TEST=Build and boot to OS in Drawlat. Ensure that the firmware test
setup and flash map test are successful. Ensure that the event logs are
synced properly between reboots. Ensure that the suspend/resume sequence
is working fine. Ensure that the ChromeOS firmware update completes
successfully for the boot image with updated flash map and the system
boots fine after the update.
Change-Id: I53ada5ac3bd73bea50f4dd4dd352556f1eda7838
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46569
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable caching of memory training data for recovery as well as normal
mode because memory training is taking too long in recovery as well.
This required creating a space in the fmap for RECOVERY_MRC_CACHE.
BUG=b:150502246
BRANCH=None
TEST=Run power_state:rec twice on lazor. Ensure that on first boot,
memory training occurs and on second boot, memory training is
skipped.
Change-Id: Id9059a8edd7527b0fe6cdc0447920d5ecbdf296e
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46651
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Create the metaknight variant of the waddledee reference board by
copying the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.2.0).
BUG=b:169813211
BRANCH=None
TEST=util/abuild/abuild -p none -t google/dedede -x -a
make sure the build includes GOOGLE_METAKNIGHT
Signed-off-by: Tim Chen <tim-chen@quanta.corp-partner.google.com>
Change-Id: Ia2e473eb1d0a2c819b874e497de0823fca75645a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46568
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Enhance USB 2.0 SI by increasing the level of "HS DC Voltage Level"
and "Disconnect Threshold Adjustment".
COMPDISTUNE0: 0x3->0x7
TXVREFTUNE0: 0x6->0xf
BUG=b:162614573
BRANCH=zork
TEST=1. emerge-zork coreboot
2. check U2 registers are set correctly
3. test with servo v4 type-c, it's working expectedly.
4. U2 SI pass
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Change-Id: I278cc0aaddbc9fce595bf57ca69ee8abfc9f5659
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46537
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Correct the two load line slope settings for the SVID3 telemetry.
AGESA sends these values to the SMU, which accepts them as units
of current. Proper calibration is determined by the AMD SDLE tool
and the Stardust test.
BUG=b:168265881
BRANCH=zork
TEST=emerge-zork coreboot
Change-Id: Id6c4f1a92d7f2ad293df7b63694e9665b85f8018
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46472
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Early JSL silicon hang while booting Linux with ISST enabled. The
malfunctioning silicon revisions have been used only for development
purposes and have been phased out. Thus, drop the ISST workaround.
Change-Id: Ic335c0bf03a5b07130f79c24107a1b1b0ae75611
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46459
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Get rid of legacy pad macros by replacing them with their newer
equivalents.
TEST: TIMELESS-built board images match
Change-Id: I078f9bb3c78f642afc6dcfd64d77be823a4485c2
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46567
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Update PL1 max and min power values
BUG=None
BRANCH=None
TEST=build and verify on dralat system
Change-Id: I75d47fa721576564f71fbd5d5fd2e820fc3f1925
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46502
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Configure board specific DPTF parameters for terrador and todor
BUG=b:171019363,b:170699797
BRANCH=volteer
TEST=build and verify by thermal team
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I19935ca98ec7a078869e73d65ea471df70f37121
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46487
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Add devicetree and device ID for P-sensor
BUG=b:161217096
BRANCH=NONE
TEST=We can get the data from P-sensor if touch the SAR antenna.
Signed-off-by: alec.wang <alec.wang@lcfc.corp-partner.google.com>
Change-Id: I70f303995b106cca9758b36ebcde112ebcc90950
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46333
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Jamie Chen <jamie.chen@intel.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
No recent Chromebooks have used I2C for TPM communication, and as a
result, a bug has crept in. The ability to extract Cr50 firmware string
is only supported via SPI, yet code in mainboard and vendorcode attempt
to do so unconditionally.
This CL makes it such that the code also compiles for future designs
using I2C. (Whether we want to enhance the I2C protocol to be able to
provide the version string, and then implement the support is a separate
question.)
This effort is prompted by the desire to use reworked Volteer EVT
devices for validating the new Ti50/Dauntless TPM. Dauntless will
primarily be using I2C in upcoming designs.
BRANCH=volteer
TEST=util/abuild/abuild -t GOOGLE_VOLTEER -c max -x
Change-Id: Ida1d732e486b19bdff6d95062a3ac1a7c4b58b45
Signed-off-by: jbk@chromium.org
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46436
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
This reverts commit c4a5acdabc.
Reason for revert: Dalboz is missing pull-up on cmd line, so 400khz is not possible.
TEST=Boot Dalboz
BUG=b:159823235, b:169940175
BRANCH=zork
Change-Id: I89653bfeefa522c17ee2d736215bc22aa445871c
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45004
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
The camera sensor component chosen for UFC and WFC have an address
conflict. Resolve it by enabling GPIO based I2C Multiplexer. Also
configure the GPIO that is used as select line.
BUG=b:169444894
TEST=Build and boot waddledee to OS. Ensure that the ACPI identifiers
are added for I2C devices multiplexed using I2C MUX under the
appropriate scope.
Change-Id: I9b09e063b4377587019ade9e6e194f4aadcdd312
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45912
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Enable the USB4 retimer driver with GPP_H10 as the power control.
Change-Id: I166bc477f94c159bb411620a6bf77b5d1f194fb2
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44919
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
To support camera second source GC5035 for kodama, add world facing
camera id as part of the sku id, which is determined by the data in
camera EEPROM. For models other than kodama, the camera id is always 0
and hence the sku id is unchanged.
BUG=b:144820097
TEST=emerge-kukui coreboot
TEST=Correct WFC id detected for kodama with GC5035 camera
BRANCH=kukui
Change-Id: I63a2b952b8c35c0ead8200d7c926e8d90a9f3fb8
Signed-off-by: Yu-Ping Wu <yupingso@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45811
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch adds some Kconfig hints to make it clearer that the
USE_QC_BLOBS option is required for SC7180 boards and guide the user in
the right direction through menuconfig. Also add those little arrows to
the Trogdor board options that are there on most other boards.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I973cae8026a229408a1a1817c4808b0266387ea7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45214
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philip Chen <philipchen@google.com>
Berknip has SSD/eMMC SKU, we should turn off eMMC if storage is NVMe SSD.
BUG=b:170592992
BRANCH=zork
TEST=1. emerge-zork coreboot
2. Check eMMC is enabled or disabled based on the eMMC bit in
FW_CONFIG.
Change-Id: I7aeabc98fc16bc2837c8dcdc40c3c6a80898cdc9
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46292
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
HybridStorageMode FSP UPD needs to be set only for optane storage.
Enabling HybridStorageMode causes some extra delay in FspSiliconInit due
to HECI command and hence is avoided for NVMe and SATA scenerios. This
change disables "HybridStorageMode" for volteer baseboard. For boards
using optane HybridStorage needs to be enabled from overwrite devicetree.
We are enabling HybridStorage for volteer and volteer2 as those plaforms
have SKU's with optane storage.
BUG=b:158573805
TEST=Build and boot non optane device and confirm that FspSiliconInit
time is reduced. This saves ~100ms.
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Change-Id: I54fc78e3f888d4f2a02ba0ad6b9aef33eb872a9c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45643
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Add tcc, critical, passive policy, and pl values from thermal team.
BUG=b:169215576
TEST=build and verify by thermal tool
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Change-Id: I4f61eaa7eab2b86b04ff0541886621afb3082b1a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45784
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Enable ALS ACPI devices for dooly.
BUG=b:168426118
BRANCH=puff
TEST=Ensure that ALS devices are enabled in ACPI tables.
Change-Id: Idd44d6ae1e7b62939fdfc3a0ab01924d2c1714aa
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46061
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Create the elemi variant of the volteer reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.2.0).
BUG=b:170604353
BRANCH=None
TEST=util/abuild/abuild -p none -t google/volteer -x -a
make sure the build includes GOOGLE_ELEMI
Change-Id: I6013b6d8b28610a79f5ec49d373b2897799bffef
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46294
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
This change switches all mainboard devices to use drivers/wifi/generic
instead of drivers/intel/wifi chip driver for Intel WiFi
devices. There is no need for two separate chip drivers in coreboot to
handle Intel and non-Intel WiFi devices since the differences can be
handled at runtime using the PCI vendor ID. This also allows mainboard
to easily multi-source WiFi chips and still use the same firmware
image without having to distinguish between the chip drivers.
BUG=b:169802515
BRANCH=zork
Change-Id: Ieac603a970cb2c9bf835021d1fb0fd07fd535280
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46035
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
1. Add speaker amplifier ALC1015
2. Enable dmic+ssp registers for speaker and camera DMIC
3. Correct I2C#2 to LVDS, I2C#3 to Touchscreen
BUG=b:170273526
BRANCH=puff
TEST=Build and check DUT function status
Change-Id: I5f6f19b40c6fcce8dca9b010ae97ea6e3eeb1473
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46289
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Remove unused device in Dooly
no SD card reader
no built-in LAN
BUG=b:170273526
BRANCH=puff
TEST=Build and check DUT function status
Change-Id: I8ab1e156031bfb4d5ea30048d8a10400f2a49411
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46288
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Dooly has USBA*2 and USBC*2
BUG=b:170273526
BRANCH=puff
TEST=Build and check DUT function status
Change-Id: Icb66a8d5382ca9664e7f0b3660f446aeb3cf1dd3
Signed-off-by: Tony Huang <tony-huang@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46126
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
GPP_A19 and GPP_A20 set no connection, disables DdiPort1Hpd and DdiPort2Hpd
BUG=b:169690329
TEST=build and verify type-c(C0/C1) port functional normally
Signed-off-by: Pan Sheng-Liang <sheng-liang.pan@quanta.corp-partner.google.com>
Change-Id: I4405526ae777332d3c72041db7b4eda25ae31b8e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46069
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: TH Lin <t.h_lin@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Refactor DPTF section of code under the baseboard devicetree
and overridetree. This makes override mechanism more simpler,
because not all the DPTF fields need to be overridden.
BUG=None
BRANCH=None
TEST=Built and tested on dedede system
Change-Id: I8e7cfe60c010ed4c07f9089325b289519e861f84
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46090
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Fix typo for power limit values under comment section in baseboard
BUG=None
BRANCH=None
TEST=Build for volteer system
Change-Id: I879b9587e863360bf4efda4099d96b42b904377e
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46220
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Add trackpad, touchscreen, and usb port to devicetree
BUG=b:160664447
BRANCH=NONE
TEST=build bios and verify theirs function for boten
Signed-off-by: alec.wang <alec.wang@lcfc.corp-partner.google.com>
Change-Id: I057f7d15d20d1a78acd733cc5463357e9c87afb2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45732
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Add SPD support for DDR4 memory part H5ANAG6NCJR-XNC.
Eldrid should use DRAM_ID strap ID 4 (0100) on SKUs populated
with H5ANAG6NCJR-XNC DDR4 memory parts.
BUG=b:161772961
TEST="FW_NAME=eldrid emerge-volteer coreboot" and verify it builds
successfully.
Change-Id: Ia26315479ce1a749a0f7c9e81f134f7068d7eb0b
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45963
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This will reduce boot time by 7ms. Some of the initial designs
don't have a pull-up resistor on the CMD line. These designs still boot
at 400 kHz despite not having the pull-up.
BUG=b:158766134
TEST=Boot dirinboz, run integrity test, b:169940185
BRANCH=zork
Signed-off-by: Rob Barnes <robbarnes@google.com>
Change-Id: I6bac8284b67070ff2c5838257f4ae2ead0e69c22
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45934
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Sam McNally <sammc@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This will reduce boot time by 7ms. Some of the initial designs
don't have a pull-up resistor on the CMD line. These designs still boot
at 400 kHz despite not having the pull-up.
BUG=b:158766134
TEST=WIP
BRANCH=zork
Signed-off-by: Rob Barnes <robbarnes@google.com>
Change-Id: I1191d73a2a3f72f99de187a946162460acbb287a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45935
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This will reduce boot time by 7ms. Some of the initial designs
don't have a pull-up resistor on the CMD line. These designs still boot
at 400 kHz despite not having the pull-up.
BUG=b:158766134
TEST=WIP
BRANCH=zork
Signed-off-by: Rob Barnes <robbarnes@google.com>
Change-Id: I2fcbe35103020c3444902c077b4985f87f970671
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45936
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This will reduce boot time by 7ms. Some of the initial designs
don't have a pull-up resistor on the CMD line. These designs still boot
at 400 kHz despite not having the pull-up.
BUG=b:158766134
TEST=Boot on Vilboz with emmc
BRANCH=zork
Signed-off-by: Rob Barnes <robbarnes@google.com>
Change-Id: I9a1e47dbee3fcc7317857d40c5418be30d755d61
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45933
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
A SATA drive may be connected to SATA0.
BUG=b:162909831
BRANCH=puff
TEST=none
Change-Id: I2a4ce2f89fa6d786358e01add15f2eedfbe4b20f
Signed-off-by: Sam McNally <sammc@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46270
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
This change drops maxsleep parameter from chip config and instead
hardcodes the deepest sleep state from which the WiFi device can wake
the system up from to SLP_TYP_S3. This is similar to how other device
drivers in coreboot report _PRW property in ACPI. It relieves the
users from adding another register attribute to devicetree since all
mainboards configure the same value. If this changes in the future, it
should be easy to bring the maxsleep config parameter back.
BUG=b:169802515
BRANCH=zork
Change-Id: I42131fced008da0d51f0f777b7f2d99deaf68827
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46033
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Use the device aliases provided by tigerlake chipset.cb instead of
the raw pci device+function. Take advantage of the default states
in chipset.cb and only list the devices that are enabled for all
volteer variants.
Change-Id: I5620004afd7fa4d50389f32dd79148960a2b2662
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44039
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently, trogdor devices have a section RO_DDR_TRAINING that is used
to store memory training data. Changing so that we reuse the same
mrc_cache API as x86 platforms. This requires renaming
RW_DDR_TRAINING to RW_MRC_CACHE and removing RO_DDR_TRAINING in the
fmap table.
BUG=b:150502246
BRANCH=None
TEST=FW_NAME="lazor" emerge-trogdor coreboot chromeos-bootimage
Make sure that first boot after flashing does memory training
and next boot does not.
Boot into recovery two consecutive times and make sure memory
training occurs on both boots.
Change-Id: I16d429119563707123d538738348c7c4985b7b52
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46111
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
1. Apply the DPTF parameters received from the thermal team.
BUG=b:169183507
TEST=build and verify by thermal tool
Signed-off-by: Terry Chen <terry_chen@wistron.corp-partner.google.com>
Change-Id: I1a1a0f9e86e519ac15904fac80cf3c2299213e52
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46087
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
If Cr50 is running old firmware version and hence does not ensure long
interrupt pulses, override the GPIO PM configuration.
BUG=None
TEST=Build and boot waddledee to OS. Ensure that any chip override
happens before FSP silicon parameter initialization. Ensure that the
suspend/resume sequence works fine. Ensure that the reboot sequence
works fine for 50 iterations.
Change-Id: I455c51d4a63b1b5edadbf00c786ce61b0ba1ff00
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45857
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
ALS is not stuffed in octopus boards. Hence disable ALS ACPI devices.
BUG=b:169245831
BRANCH=octopus
TEST=Ensure that ALS devices are disabled in ACPI tables.
Change-Id: I5ad28f01b0515a41b314116eb2d05c520df0f86e
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45741
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This will reduce boot time by 7ms. Some of the initial designs
don't have a pull-up resistor on the CMD line. These designs still boot
at 400 kHz despite not having the pull-up.
BUG=b:158766134
TEST=Boot Berknip w/ eMMC to OS.
BRANCH=zork
Change-Id: I5d55f55b8208b4dc3fbdc9d1ec6333f9e211e3fd
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45931
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Current Ram_Id: 0011 MT40A1G16KNR-075-E never be built before.
Remove it and change use micron-MT40A1G16KD-062E-E for ram_id:0011.
BRANCH=zork
BUG=b:159316110
TEST=run gen_part_id then check the generated files.
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Change-Id: I28fc39f17e06ecd39f6567613e6ff5919becb2fd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45810
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This will reduce boot time by 7ms. Some of the initial designs
don't have a pull-up resistor on the CMD line. These designs still boot
at 400 kHz despite not having the pull-up.
BUG=b:158766134
TEST=Boot Ezkinil w/ eMMC to OS.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ida0bbf9bd772ab7d384d5d097fa3b02b846a3efa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45852
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Eric Peers <epeers@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This will reduce boot time by 7ms. Some of the initial designs
don't have a pull-up resistor on the CMD line. These designs still boot
at 400 kHz despite not having the pull-up.
BUG=b:158766134
TEST=Boot on morphius with and without patch, confirm ~7ms improvement
BRANCH=zork
Signed-off-by: Rob Barnes <robbarnes@google.com>
Change-Id: I7f6efd3d5839f154f2487a07654be8e35634bbbc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45932
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Implement mainboard_silicon_init_params() to allow for disabling of
TBT root ports if the device does not have usb4 hardware.
Add code to mainboard_memory_init_params() to disable memory-related
settings associated with TBT in cases where no usb4 is available.
BUG=b:167983038
TEST=none
Change-Id: Iab23c07e15f754ca807f128b9edad7fdc9a44b9d
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45946
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
To remove the xhci0_force_gen1 and use usb3_port_force_gen1 instead.
The xhci0_force_gen1 is used for force all port on xhci0 to USB3 GEN1.
Now variant can use the usb3_port_force_gen1 to customize which port
it needs to limit.
BUG=b:167651308
BRANCH=zork
TEST=Build, verify the USB3 speed in gen1
Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Change-Id: If5f0c1f22d8c98c4461f09d074bf082c340b14d9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46041
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
In morphius, the USB3 typeA port needs to set to gen1, and for ezkinil
all the USB3 ports should force to gen1. So set the corresponding
setting to usb3_port_force_gen1 to force USB3 to Gen1.
BUG=b:167651308
BRANCH=zork
TEST=Build, verify the USB3 speed in gen1
Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Change-Id: I10419b91fe86fe3e06de36ddfe0d1769c1031f8e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45334
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Add support for trackpoint wakeup from S3 by adding device events to
mainboard and defining for morphius.
BUG=b:160345665
BRANCH=zork
TEST=tested trackpoint wake from S3 on morphius DVT
Signed-off-by: Josie Nordrum <josienordrum@google.com>
Change-Id: I982f0f4b60fbaeb389774531e1dee83da77cb8a1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45965
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Adjust Touchscreen delay off values to let suspend off timing match
power down specificatiion.
BRANCH=zork
BUG=b:163434386
TEST=Measuring scope timing
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Change-Id: I58866122f441cc3c427e659b8a5fdb6643987882
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45785
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
This patch makes Fleex EC wake up AP from s0ix when the state of
charge drops to 5%.
Demonstrated as follows:
1. Boot Fleex.
2. Run powerd_dbus_suspend.
3. On EC, run battfake 5.
4. System resumes.
BUG=b:163721887
BRANCH=Octopus
TEST=Verified on Fleex:
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Change-Id: I4a998ad0aef5a7cfc6fd18995bde5571e6127e77
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45967
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Enable CHROMEOS_DRAM_PART_NUMBER_IN_CBI on hatch, dedede, and volteer
to use the common version of mainboard_get_dram_part_num().
Remove duplicate instances of mainboard_get_dram_part_num().
BUG=b:169789558, b:168724473
TEST="emerge-volteer coreboot && emerge-hatch coreboot &&
emerge-dedede coreboot" and verify it builds.
Change-Id: I4e29d3e7ef0f3370eab9a6996a5c4a21a636b40e
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45883
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Change mainboard_get_dram_part_num() to return a constant character
pointer to a null-terminated C string and to take no input
parameters. This also addresses the issue that different SOCs and
motherboards were using different definitions for
mainboard_get_dram_part_num by consolidating to a single definition.
BUG=b:169774661, b:168724473
TEST="emerge-volteer coreboot && emerge-dedede coreboot && emerge-hatch
coreboot" and verify build completes successfully.
Change-Id: Ie7664eab65a2b9e25b7853bf68baf2525b040487
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45873
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch moves platform.asl into common block acpi directory to
avoid duplicating the same ASL code block across SoC directory.
TEST=Able to build and boot TGL, CNL and CML platform.
1) Dump and disassemble DSDT, verify _PIC method present inside
common platform.asl is still there.
2) Verify no ACPI error seen while running 'dmesg` from console.
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Change-Id: I5189b03d6abfaec39882d28b40a9bfa002128be3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45982
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Configure EMMC_RESET_L (GPIO68) to drive high by default. As per JEDEC
specification for eMMC, RST_n_FUNCTION defaults to temporarily disable
reset using RST_n signal (which is connected to EMMC_RESET_L on
zork). Chrome OS platforms do not configure RST_n_FUNCTION thus making
the reset signal unused. The spec also says that there are no internal
pulls on the card and hence the RST_n signal should be driven
appropriately to prevent the input circuits from flowing unnecessary
leakage current.
Thus, even though the line remains unused, since it is connected in
hardware, this change drives EMMC_RESET_L to high.
BUG=b:169222156
BRANCH=zork
TEST=emerge-zork coreboot
eMMC DUT reboot/suspend x100 iterations pass
Change-Id: I9feb826eec8a8cdad5e2bd7efcbb1dcf96185dfd
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45756
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
This fix needs to go into ACPI in the long-term, but this
should suffice in the short-term.
BUG=b:158087989
TEST=Boot berknip, verify backlight is enabled. Test suspend
& resume sequence, backlight is still enabled.
BRANCH=Zork
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I6ecc3c9e397c9756a78e480d3f639c507879a0ea
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45854
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The SMU code was assuming that GPIO 85 was used for a fan, which caused
interesting backlight flickering. That has now been fixed, so remove
the code that reconfigured it to a GPIO on resume.
BUG=b:155667589
TEST=Verify the screen does not flicker on resume from S3
BRANCH=Zork
Signed-off-by: Martin Roth <martinroth@chromium.org>
Change-Id: I6d4f9d98e9df52fefab9b20d0ab0f0b67512d356
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45853
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
This patch updates the SLP_Sx assertion widths and power cycle duration
for volteer.
Power cycle duration:
With default value,
S0->S5 -> [ ~4.2 seconds delay ] -> S5->S0
With value set to 1,
S0->S5 -> [ ~1.2 seconds delay ] -> S5->S0
BUG=b:159108661
TEST=Verified that the power cycle duration is 1~2s with a global reset
on volteer.
Signed-off-by: Jamie Ryu <jamie.m.ryu@intel.com>
Change-Id: Idf4e0c3a60b4ac59e31df1357f2ff28f195ff17f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44559
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
1. TSRO trip point from 75C change to 73C
2. Sample period time from 5s change to 60s
BUG=b:160385395
BRANCH=puff
TEST=build and verify by thermal team
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I0b000841845ce793be0e52fc28a07ac6a931ef7a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45729
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sam McNally <sammc@google.com>
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
The default GPIO values for camera power were set as 1 so the LED was
turned on by default when the board is powered on.
This status is kept until the camera is probed then being turned off.
So the LED is turned on for a few seconds during the boot up.
By setting the default power to 0, the LED is lit only when camera
is turned on for probing and this should be just a blink.
BUG=b:167635396
BRANCH=none
TEST=Build and boot volteer board. Monitor camera privacy LED
and check it is not lit more than 0.5 seconds.
Signed-off-by: Daniel Kang <daniel.h.kang@intel.com>
Change-Id: Ic7df391aa512daafe6e1ce49e9222b90e17ad806
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45058
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
cameras
There is a patch https://lkml.org/lkml/2020/9/3/235 which allows i2c
device can support driver probe without power up the device.
In order to support this, need add coreboot add
"i2c-allow-low-power-probe" property.
BUG=b:169058784
BRANCH=none
TEST=Build and boot volteer board. Monitor camera privacy LED
and check it blinks. It should not blink.
Signed-off-by: Daniel Kang <daniel.h.kang@intel.com>
Change-Id: I46f90ff8d412b18c7ee4bd7f22f9a7db771eb84f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45160
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Only do LTE power off for LTE sku in order to save extra 130ms delay
for non-LTE sku.
BUG=b:168075958
BRANCH=octopus
TEST=build image and verify on the DUT with LTE DB.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: If983185ff2f09fb1b2553c6ff1a1473d3254de4b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45687
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marco Chen <marcochen@google.com>
They should be tuned per board to get the best signal and boot time.
This fixes the HS400 preset, so it's correctly set to A. It also changes
the SDR50 and DDR50 presets to B. We can't boot correctly when DDR50 is
set to A.
I chose 1 as the init kHz value since that's what depthcharge uses to
calculate the init clock.
BUG=b:159823235
TEST=Boot Ezkinil and dump SDHCI preset registers.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: Ie2f3497b65d771820ab1a803fec73265547f8906
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45098
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Use Wifi SAR table for non-LTE sku only.
BUG=b:169115341
BRANCH=octopus
TEST=Check no SAR table can be loaded with sku id 4.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I086fa14a9f23e4a0fc0ef8085040219c932dbf17
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45640
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
GPP_S4 and GPP_S5 use as DMIC pins that need to be defined as NF2
BUG=b:168564129
Signed-off-by: nick_xr_chen <nick_xr_chen@wistron.corp-partner.google.com>
Change-Id: Ia1fca960ac85f253882f0aa68b370eed49ac67b7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45689
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-by: Ravishankar Sarawadi <ravishankar.sarawadi@intel.com>
It needs to use probe statement in overridetree.cb to enable the cache
of fw_config field implemented by cb:44782 and cb:44783.
BUG=b:161963281
TEST= dmidecode -t 11 shows correct audio fw_config.
Handle 0x0009, DMI type 11, 5 bytes
OEM Strings
String 1: DB_USB-USB4_GEN2
String 2: AUDIO-MAX98373_ALC5682I_I2S_UP4
Signed-off-by: Kevin Cheng <kevin.cheng@intel.com>
Change-Id: I68c19b67d945aaca3e9ebec87eb27a4b07e1a49e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45673
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Camera ACPI tables are generated at run-time for all variants of Dedede.
BUG=None
TEST=Build madoo variant.
Change-Id: Icb74c01a0a6dbc620466b64cd2b5652408ca41b9
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45626
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
In order to pass DB type-C USB2 eye diagram, DB USB2 PHY register needs
to be overridden.
port#1
PortUsb20Enable=1
Usb2PhyPetxiset=7
Usb2PhyTxiset=7
Usb2PhyPredeemp=3
Usb2PhyPehalfbit=0
BUG=b:169105751
Signed-off-by: nick_xr_chen <nick_xr_chen@wistron.corp-partner.google.com>
Change-Id: If076c644783fa2992ac062d6469f9c49e6d5ff24
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45598
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
update the telemetry setting for second SDLE testing(for APU power adjusting).
Those values are used to power calibration the APU power and achieving
the best performance.
BUG=b:160698427
BRANCH=zork
TEST=emerge-zork coreboot
Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Change-Id: I4cf5b8f090befd6a3c4990f44f2f200bc66aa1f4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44804
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
These parts have not been used in any vilboz devices. Removing
so IDs can be assigned more efficiently.
Command to generate files:
go build gen_part_id.go
local variant=vilboz
./gen_part_id ../../../src/mainboard/google/zork/spd ../../../src/mainboard/google/zork/variants/${variant}/spd/ ../../../src/mainboard/google/zork/variants/${variant}/spd/mem_parts_used.txt
BUG=b:165611994
TEST=none
Change-Id: I99614acaf45db0556120c883577494d9f753ea12
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45679
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Rob Barnes <robbarnes@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add memory part H5ANAG6NDMR-XNC. Attributes are derived from data
sheets.
BUG=b:165611994
TEST=Compared generated SPD with data sheets and checked in SPD
Change-Id: Ifdcc7536441e9f0b94543c6f06fe466596f752dc
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45647
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Morphius has SSD/eMMC SKU, we should turn off eMMC
if storage is NVMe SSD.
BUG=b:169211959
BRANCH=zork
TEST=1. emerge-zork coreboot
2. Check eMMC is enabled or disabled based on the eMMC bit in
FW_CONFIG.
Change-Id: I67d5d77ce3d827ae89b82529de59925f67eaf894
Signed-off-by: Kevin Chiu <kevin.chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45755
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Create the boldar variant of the volteer reference board by copying
the template files to a new directory named for the variant.
(Auto-Generated by create_coreboot_variant.sh version 4.2.0).
Add "memory/Makefile.inc" generated by gen_part_id.go
BUG=b:162202257
BRANCH=None
TEST=util/abuild/abuild -p none -t google/volteer -x -a
make sure the build includes GOOGLE_BOLDAR
Signed-off-by: Ronak Kanabar <ronak.kanabar@intel.com>
Change-Id: I92b4b917448d8e5e9176cb983adf7b209956d2c2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45648
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Drop lpit.asl from CNL and switch to the common one in the three boards
currently using it.
The only difference between the two is the usage on macros in common
code instead of plain integer values.
Change-Id: Iefbd18db7f4c560dce16c4119fde4f4cfbeafb84
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45549
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Fagerburg <pfagerburg@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This change enables CnviBtAudioOffload. FSP is invoked to configure
BT over USB and BT I2S pins for cAVS connection.
BUG=b:169045123
TEST=Verifed CnviBtCore and CnviBtAudioOffload settings and FSP
configuration. Booted up to kernel on Volteer.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I1780da0824d145a79743d5cffdea4821236d4f74
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45586
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Naveen M <naveen.m@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Now that we're using fmaptool to parse the .fmd file, we can use some
short forms and omit unnecessary information.
BUG=b:157068645
TEST=None
BRANCH=zork
Change-Id: I81c121d4fce13a9d2aad4477955cb4770794d244
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45597
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
0x12 will be more stable according to validation result on SD card and
USB devices.
BUG=b:163382089
BRANCH=none
TEST=check if SD cards and USB devices work properly
Signed-off-by: Marx Wang <marx.wang@intel.com>
Change-Id: Ic98f27b6164daa3667009300439c61fed43a4a0b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45573
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Henry Sun <henrysun@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The name GENERIC_SPD_BIN doesn't reflect anymore what that config is
used for, so rename it to HAVE_SPD_BIN_IN_CBFS.
Change-Id: I4004c48da205949e05101039abd4cf32666787df
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45147
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable processor thermal control using PCI dev path function instead of
Device4Enable parameter in devicetree. This change removes the dependency
on Device4Enable in devicetree. We can enable and disable this thermal
control using on and off support with PCI device entry in devicetree.
BRANCH=None
BUG=None
TEST=Built and tested on dedede board
Change-Id: I0463236996ad001af506c9966840b27fe44d60d2
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45454
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Lets have the Kconfig depend more directly on CSE_LITE_SKU
than indirectly on the PUFF baseboard.
BUG=none
BRANCH=puff
TEST=builds
Change-Id: I8784b506629ceedc2770dc86d8caabbef5eb8a1d
Signed-off-by: Edward O'Callaghan <quasisec@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45523
Reviewed-by: Sam McNally <sammc@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
All octopus board share the same power off sequence.
Move to smihandler.c instead variant.c.
BUG=b:168075958
BRANCH=octopus
TEST=build image and verify on the DUT with LTE DB.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I2be5a656fb42fff99c56d21aaa73ed9140caad37
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45436
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add wifi sar for madoo.
Using tablet mode of fw config to decide to load custom wifi sar or not.
BUG=b:165105210
TEST=enable CHROMEOS_WIFI_SAR in config of coreboot,
emerge-dedede coreboot-private-files-baseboard-dedede coreboot chromeos-bootimage.
Signed-off-by: Dtrain Hsu <dtrain_hsu@compal.corp-partner.google.com>
Change-Id: Ic6128b966c952cdc02a6359c14fa41f22265039a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45439
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
This sets the state of GSPI chip select to 1 (deasserted) as applied
by the FSP during the silicon init phase. GSPI 0 and 1 are set to CS
mode manual in the SerialIoGSpiCsMode section which means we need to
explicitly configure CS to deasserted in the SerialIoGSpiCsState
section. GSPI0 is the CR50 and GSPI1 is the fingerprint sensor. We
were running into problems where the normal expected CS toggle
sequence to wake up CR50 did not work because CS was already asserted
when it was expected to be deasserted, leading to TPM timeouts.
BUG=b:168090038
TEST=booted on volteer, no more "TPM flow control failure" messages;
verified fingerprint enrollment still works.
Change-Id: I47aa5db429d75e66095d58a1eb77963dcfc3b9f3
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45384
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add newly defined fields for presence of keyboard backlight and
number pad to the firmware configuration table.
We don't have a need to use these in coreboot (yet) but this
keeps the bit definitions in sync.
BUG=b:166707536
TEST=abuild -t google/volteer
Change-Id: I066e445f7d0be056e45737d2c538be1850ae85aa
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45346
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Enable CSE PCI device Bus 0: Device 0x0f: Function 0x00 to let
Intel common cse block code can use this device.
Calling me_read_config32(offset) function from ramstage:
Without this CL :
HECI: Global Reset(Type:1) Command
BUG: me_read_config32 requests hidden 00:0f.0
PCI: dev is NULL!
With this CL :
HECI: Global Reset(Type:1) Command
HECI: Global Reset success!
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Change-Id: I97d221ae52b4b03ecd859d708847ad77fe4bf465
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45469
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
This patch updates the display power enable GPIO which moved from 30 to
52 for Coachz. Veterans of this project know that there's no point
trying to ask *why* this change was necessary -- the pins move in
mysterious ways and all we can do is watch and wonder. Pin 30 is now
used for a new camera reset GPIO... surely, there must have been some
excellent reason why that pin couldn't just have become pin 52 instead.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I00ad6a6249df66006b4f2b953a0a2449bd478f6d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45306
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Philip Chen <philipchen@google.com>
GPIOs related to power sequence are
GPIO_67 - EN_PP3300
GPIO_117 - FULL_CARD_POWER_ON_OFF
GPIO_161 - PLT_RST_LTE_L
1. Power on: GPIO_67 -> 0ms -> GPIO_117 -> 30ms -> GPIO_161
2. Power off: GPIO_161 -> 30ms -> GPIO_117 -> 100ms -> GPIO_67
3. Power reset:
- keep GPIO_67 and GPIO_117 high and
- pull down GPIO_161 for 30ms then release it.
BUG=b:168075958
BRANCH=octopus
TEST=build image and verify on the DUT with LTE DB.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I9b56ef8ff346c1d4edd5aad04d4a7396c4702ffc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45193
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Henry Sun <henrysun@google.com>
Reviewed-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This allows us to drop some casts to uintptr_t around the tree.
The MCHBAR32 macro still needs a cast to preserve reproducibility.
Only the native raminit path needs the cast, the MRC path does not.
Tested with BUILD_TIMELESS=1, these boards remain identical:
- Lenovo ThinkPad X230
- Dell OptiPlex 9010
- Roda RW11 (with MRC raminit)
Change-Id: I8ca1c35e2c1f1b4f0d83bd7bb080b8667dbe3cb3
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45349
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
RCBA is located in the PCH. Replace all instances with the
already-defined `DEFAULT_RCBA` macro, which is equivalent.
Change-Id: I4b92737820b126d32da09b69e09675464aa22e31
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45348
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
GPP_A19(DP_HPD1) and GPP_A20(DP_HPD2) were configured native function
(NF1) without internal pull-down which wrongly presents HPD interrupts.
This change configures GPP_A19 and GPP_A20 to be no connection and
disables DdiPort1Hpd and DdiPort2Hpd.
BUG=b:165893624, b:168090618
Signed-off-by: nick_xr_chen <nick_xr_chen@wistron.corp-partner.google.com>
Change-Id: I31b25be1c9248debf855435c7b688b358e2cd57e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45246
Reviewed-by: Scott Chao <scott_chao@wistron.corp-partner.google.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change updates devicetree to enable SSDT generation for world
facing camera and user facing camera of Waddledoo. Also reverts DSDT
changes related to both the camera.
Signed-off-by: Pandya, Varshit B <varshit.b.pandya@intel.com>
Change-Id: Ib7e875d297c04f35d4e980ff33d9a3767d2910ac
Signed-off-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44397
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
This enables the keyboard backlight feature in ACPI for madoo.
BUG=b:167943993
TEST=Verified 'kbd_backlight' shows up in the '/sys/class/leds '.
Signed-off-by: Ian Feng <ian_feng@compal.corp-partner.google.com>
Change-Id: I11531699cb650b96becae5c1bec9f89c48b6bea0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45330
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
The gpio90 EN_PWR_TOUCHSCREEN had been set to PAD_GPO(GPIO_90, LOW), but
addtional PAD_NC(GPIO_90) cause enable fail. remove it for issue fixed.
BRANCH=zork
BUG=b:168580357
TEST=Check Touchscreen function work
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Change-Id: Id94dd63ba51759cebaf17779a5e659dbe0f1807f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45415
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Fingerprint interrupt (FPMCU_INT_L) is level triggered and not edge
triggered. Also, we are using GEVENT for wake from fingerprint and
not the GPIO IRQ wake. Thus, the irq property exposed in ACPI tables
does not need to be set to indicate wake for the IRQ.
This change updates GPIO table to configure the pad as level triggered
and drops the wake attribute for irq_gpio in overridetree.
BUG=b:165612778
BRANCH=zork
TEST=Verified that fingerprint still works in S0 and to wake device
from S3.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I9007e5b0882ac1a6770db52d651218998f6d750d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45307
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
I plan on adding another eMMC parameter. This refactor keeps the config
contained in a single struct.
BUG=b:159823235
TEST=Build test
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I4b57d651ab44d6c1cad661d620bffd4207dfebd4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45095
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
GPP_A19(DP_HPD1) and GPP_A20(DP_HPD2) were configured native function
(NF1) without internal pull-down which wrongly presents HPD interrupts.
DP_HPD had been removed for EVT design as those events are through eSPI.
This change configures GPP_A19 and GPP_A20 to be no connection and
disables DdiPort1Hpd and DdiPort2Hpd.
BUG=b:162566436
TEST=Booted to kernel and verified no kernel HPD pins assertion message
on Delbin board.
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com>
Change-Id: Ifdef8ee438276678258b75d2fb70c6dfc7ee0a33
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45031
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
BUG=b:167297664
BRANCH=octopus
TEST=build fleex, and check touchscreen can work
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Change-Id: I910681c258ff5487830e795a8bd08c66be69b1d4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44980
Reviewed-by: Justin TerAvest <teravest@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Marco Chen <marcochen@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Henry Sun <henrysun@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
GPP_E12 should not be defined in the baseboard as its use is
determined by the variant. For legacy reasons, we still have GPP_E12
defined in early_gpio but should not. Malefor and volteer* have the
same GPP_E12 definition, but that is a misconfiguration. I think that
was a copy-paste that slipped through the reviews.
BUG=b:157597158
TEST=volteer2 boots to the OS
Change-Id: Ic3ef864827aa94b0b96e335565119f3d5d008837
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45197
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
1. Set tcc offset to 5 degree celsius
2. Apply the DPTF parameters received from the thermal team.
BUG=b:167523658
TEST=build and verify by thermal team
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I01a6fc5bd959798c8dd423df3907c69c883733e8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45111
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Clean up the DPTF section of the baseboard devicetree; this makes
overrides simpler, as not necessarily all of the fields need to be
overridden.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Iad46fd02f7602c9419d7c3674b0d2b6f5add9a93
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45179
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Jasper Lake SoC supports PL2 (Power Limit2) as 20W. Increase PL2 value from 15W to 20W.
BRANCH=None
BUG=b:166656373
TEST=Built and tested on drawlat system
Change-Id: I82d6792907bb1c88cc9dd57d1eaeda8421c12fb2
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45162
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
That devicetree setting is about the Audio Co-Processor and not ACPI.
BRANCH=zork
Change-Id: I7f376371ee094392d4434340c77f0fc8d0d8e4e1
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45300
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
The debug statement to print WiFi SAR file can potentially have a NULL
pointer. Also the debug statement does not add much value. Hence remove the
debug statement.
BUG=b:165613510
TEST=Build and boot the drawcia board to OS.
Change-Id: I710240f5e965f523fb8ac55a67880e1cbf9abd48
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45298
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
drawman/drawlat/drawcia share the same coreboot, and only drawcia is convertible.
Use tablet mode of fw config to decide to load custom wifi sar or not.
BUG=b:165613510
TEST=enable CHROMEOS_WIFI_SAR in config of coreboot,
emerge-dedede coreboot-private-files-baseboard-dedede coreboot chromeos-bootimage.
Change-Id: Ibcd498021e63d0a172c71c3d94b60b3a25973467
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44661
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
GPP_F14 should be configured to be routed via APIC and not SCI.
BUG=b:162528549
TEST=verified on a volteer2
Signed-off-by: Alex Levin <levinale@google.com>
Change-Id: I7f2c7af230dd75b3cb3806e2b186725d49da9e68
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45279
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Apparently what I thought was lazor-rev2 is actually lazor-rev3 and
nobody is really sure what lazor-rev4 is going to be at this point or
how we proceed from there. What seems to be somewhat agreed upon is that
for now all Lazor revisions use the "old" GPIO mapping and it's not very
clear if that's ever going to change for Lazor, so let's take the
revision restriction out from Lazor for now.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: I4939ccfd8464da6e72b5e01a58489b8c80f5b4df
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45225
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Philip Chen <philipchen@google.com>
Move APCB generation out of the picasso makefile and into the mainboard
makefile. APCB generation tends to be mainboard specific and does not
belong in the soc makefile.
BUG=b:168099242
TEST=Build mandolin and check for APCB in coreboot binary
Build and boot ezkinil
Change-Id: Ib85ad94e515f2ffad58aafe06c1f1d4043e9303c
Signed-off-by: Rob Barnes <robbarnes@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45222
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add sc7180 display hardware pipeline programming support
and invoke the display initialization from soc_init.
Changes in V1:
- added display init required check.
- added edid read function using i2c communication.
- added sn65dsi86 bridge driver to init bridge.
- moved display initialization to mainboard file.
Changes in V2:
- moved diplay init sequence to mainboard file
- moved edid read function to bridge driver.
- calculated timing paramters using edid parameters.
- removed command mode config code.
- moved bridge driver to drivers/ti.
- seperated out bridge and soc code with mainboard file as interface.
Changes in V3:
- add GPIO selection at runtime based on boardid.
- add vbif register struct overlay.
Changes in V4:
- update gpio config for lazor board.
Change-Id: I7d5e3f1781c48759553243abeb3d694f76cd008e
Signed-off-by: Vinod Polimera <vpolimer@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39615
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Add sn65dsi86 bridge driver to enable the eDP bridge.
Datasheet used : https://www.ti.com/lit/ds/sllseh2b/sllseh2b.pdf
Changes in V1:
- fix the dp lanes using mask
- separate out the refclk and hpd config to init function
Change-Id: I36a68f3241f0ba316c261a73c2f6d30fe6c3ccdc
Signed-off-by: Vinod Polimera <vpolimer@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42899
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Configure GPIO pins as I2S mode for audio speaker.
The audio speaker does not work on Trogdor revision 1, as the
layout was changed.
Developer/Reviewer reference, be aware of this issue:
https://partnerissuetracker.corp.google.com/issues/146533652
Change-Id: Ia4bbfea591a3231640b53e64f0e4e9d43c4437a3
Signed-off-by: vsujithk <vsujithk@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41428
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Add new memory.c to support DDR4 memory types.
Use the new meminit_ddr() and variant_memory_sku() for eldrid variant
code on memory.c
The initial settings override the baseboard from volteer and fine tune
gpio.c and overridetree.cb on eldrid's configuration.
BUG=b:161772961
TEST='emerge-volteer coreboot chromeos-bootimage' and verify that Eldrid
can boots. NOTE that tests the ddr4 side of the implementation.
Change-Id: I2c7b30093a8d85bac5aba5b83768af5eb36c4f70
Signed-off-by: Nick Chen <nick_xr_chen@wistron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44632
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
The three Intel Apollo Lake boards (apl_rvp, leafhill and minnow3) do
not define MAX_CPUS, which would then default to 1. Since this is most
likely an oversight, use the same value as other Apollo Lake boards.
To ensure this does not happen again, factor out MAX_CPUS to SoC scope.
Change-Id: I5ed98a6b592c8010b59eca7ff773ae1ccc4cd7b1
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45144
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
APL does not support Hyper-Threading, and has at most four CPU cores.
Change-Id: Ib2ffadc0c31cdd96bec8eed5364c984acb2e1250
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45143
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Both Gemini Lake boards in the tree use the same value.
Change-Id: Ib6bd05206026736fd7e3d44b49e4d8ba217c2708
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45142
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Update critical and passive policy for TSR0.
BUG=b:167477885
BRANCH=puff
TEST=build and verify by thermal team
Signed-off-by: David Wu <david_wu@quanta.corp-partner.google.com>
Change-Id: I244e1b5cacabf5b73c47b4039ae150cd17fcd0fc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45169
Reviewed-by: Edward O'Callaghan <quasisec@chromium.org>
Reviewed-by: Sam McNally <sammc@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Sushi is not a real product, just a test of the new_variant program.
The effort to keep it up-to-date with the rest of Hatch is no longer
worth it. Remove the variant.
BUG=b:168030592
TEST=build bot is successful, hatch-cq builds successfully
Signed-off-by: Paul Fagerburg <pfagerburg@chromium.org>
Change-Id: I2b0036f3cbdea4bfaed1274ab87a20d24c75de57
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45175
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
