Disable scalability tracking for autonomous frequency control in
order to improve power and performance.
BUG=b:280021171
TEST=Boot to OS on brya0
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: If71ee5374c67611b32691bbec4effdf828b3e566
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74723
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Hook the newly exposed EnableHwpScalabilityTracking UPD up so that
boards can configure is via devicetree.
BUG=b:280021171
TEST=Verified by enabling/disabling the UPD on google/brya
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: I4c8845c445d46caa30a0245386ab9cd690d2623f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74722
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Hook the newly exposed DisableSagvReorder UPD up so that
boards can configure is via devicetree.
BUG=b:268546941
TEST=Verified by enabling/disabling the UPD on google/brya
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: I89235d9384b67f03e68425aadd3458e1c77ff555
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74720
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Disable re-ordering SaGv point on warm reset so that most
performant SaGv point is picked after memory training and
boot time is reduced.
BUG=b:268546941
TEST=Observe boot time improvement with these two UPDs set
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: I44a1c054d52bb8585a320bb8a52a8f137e639804
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74721
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable upd to reduce size of the memory test.
BUG=b:268546941
TEST=Observe boot time improvement with these two UPDs set
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: I95c7d8503596c2712d7abe123ed1f911ac4abacf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74719
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Hook the newly exposed LowerBasicMemTestSize UPD up so that
boards can configure is via devicetree.
BUG=b:268546941
TEST=Verified by enabling/disabling the UPD on google/brya
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: Ib813e9f3b7419a3cb54b4e176dcc5cc74a783dfd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74718
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
test: Warm reboot from Windows 11 w/ Samsung 980 Pro on Banshee
Verify memory type detected properly and following boot works
Change-Id: Iad0a2024bd0ef39f6ab57ff7a6e6aa651d7882a6
Signed-off-by: CoolStar <coolstarorganization@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76382
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Only A step ADL-S CPUs were added to CPU table for MP init. Add
the remaining ADL-S CPUs to the table.
TEST=Boot MSI PRO Z690-A with C step i5-12600K and observe coreboot
no longer uses generic CPU ops.
Change-Id: I3692a3f089ca23af860bd1c8e3c29fee9d9234c9
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76204
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
In newer ADL/RPL PCH EDS 619362 revision 2.1 the ESPI ID 0x7A8A
belongs to the W790 chipset. Earlier revisions had the chipset with
ID 0x7A8A named W685, which was probably just a temporary name.
Change the naming throughout the tree to W790, which is the real
existing chipset.
Change-Id: I87603298d655e9bf898b34acdd5b403f5affaee3
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76191
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Crawford <tcrawford@system76.com>
CPUID is the same for Alder Lake and Raptor Lake S and HX variants.
To reduce the confusion and concerns how to name the macros, remove
the suffixes from macros and platform reporting strings. Thankfully
the stepping names are unique across mobile (P suffixed) and desktop
(S and HX suffixed) SKUs. Distinguishing the S from HX is possible via
host bridge PCI ID.
Change-Id: Ib08fb0923481541dd6f358cf60da44d90bd75ae2
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76203
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Crawford <tcrawford@system76.com>
Add PCI IDs, default VR values and power limits for Raptor Lake S
CPUs. Based on docs 639116 and 640555.
TEST=Tested on a MSI PRO Z690-A (ms7d25) with i9-13900K with Ubuntu
22.10 and LinuxBoot (Linux + u-root). Also tested on MSI PRO Z790-P
with i5-13600K (UEFI Payload) usign RPL-S IoT FSP and Ubuntu 22.04.
Change-Id: I767dd08a169a6af59188d9ecd73520b916f69155
Signed-off-by: Max Fritz <antischmock@googlemail.com>
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69798
Reviewed-by: Tim Crawford <tcrawford@system76.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Kopeć <michal.kopec@3mdeb.com>
Some of the microcode update files listed in the Makefile are redundant:
* 06-97-02 is exactly the same as 06-97-05
* 06-9a-03 is completely contained in 06-9a-04 (at offset 0x1c400)
So drop these files. This saves us about 200KiB CBFS space in each case.
Change-Id: Idfcab1de26ea4712295c1d22790bab3a73c17f93
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76381
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
During the ACPI dump of the System Resource Affinity Table (SRAT), it
was noticed that the reserved field within the Memory Affinity structure
contained a non-zero value. This commit addresses the issue by
performing a memset to zero on the reserved field, ensuring the
avoidance of any potential problems arising from garbage values.
TEST= Build for ibm/sbp1 & make sure SRAT Memory Affinity entries
reserved fields read zeroes
Signed-off-by: Naresh Solanki <Naresh.Solanki@9elements.com>
Change-Id: I4ba697a6bd59054e74c84b98f3d9b517d333a5d8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75417
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
The AW37503 is designed to supply positive/negative supply for driving
the MIPI panel. It doesn't integrate non-volatile memory(EEPROM), so we
need to program the registers at boot. We program the target
positive/negative output voltage via I2C and enable the power rails by
pulling up ENP and ENN pins.
On Starmie, we need +/-6V power supply for the MIPI panel. We program
the AW37503 registers in coreboot so that kernel can control AW37503
via fixed regulators without additional settings(what we did for
TPS65132). Since we distinguish AW37503 and TPS65132 by reading the
vendor ID, we need to initialize I2C bus as early as possible.
Therefore, we move mtk_i2c_bus_init() to mainboard_init().
BUG=b:289482828
TEST=emerge-staryu coreboot chromeos-bootimage
TEST=Test the sequence the voltage
Change-Id: I9ccd4db19c93a032226f006eab0427f78f7b6dc8
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76219
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: cong yang <yangcong5@huaqin.corp-partner.google.com>
Reviewed-by: Yidi Lin <yidilin@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Commit cde4f3b279 ("acpi/gnvs.c: Drop unused pointer to the cbmem
console") removed writing the coreboot memory console pointer to the
GNVS and kept the CBMC field as reserved. Since those fields aren't
needed any more and there are no dependencies on the absolute position
of the different fields in GNVS as long as both GNVS definitions on the
C and the ASL side match, remove the deprecated and unused CBMC field
from the GNVS structs.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Iadfaf5a4ec1401b027dbfb6a7c6ce74a1dcecdfa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76351
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Fix below build error after DISPLAY_UPD_DATA is selected:
src/soc/intel/xeon_sp/spr/upd_display.c:131:29: error: variable 'old' set but not used [-Werror=unused-but-set-variable]
131 | const FSP_S_CONFIG *old;
| ^~~
src/soc/intel/xeon_sp/spr/upd_display.c:130:29: error: variable 'new' set but not used [-Werror=unused-but-set-variable]
130 | const FSP_S_CONFIG *new;
Change-Id: I43ed5fadab58e0d4dc824457c7a1bdf48511198e
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76342
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use the _tohex function to convert values to hex instead of 'shell
printf'
TEST=timeless builds identical for grunt,dalboz,guybrush,chausie,birman
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: Ic7f7d1b764479088cc0980b208d8d603bc712832
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76314
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
tis_plat_irq_status() function is used only by Google TPM. It should
be moved to drivers/tpm/cr50.c. The name of the function was changed
to cr50_plat_irq_status().
BUG=b:277787305
TEST=Build all affected platforms
Change-Id: I78dc39f2c7b44232b06947d3dfe6afa52807ced8
Signed-off-by: Grzegorz Bernacki <bernacki@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75917
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Rather than repeat the same line multiple times, save it in a variable
once and use that variable in the rest of the file.
TEST=timeless birman build identical
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: I4eb262adb3bbda04add79b2e2b8bee9a609a1e5b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76197
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Pass the APOB NV address as a flash offset instead of x86 address.
TEST=boot birman and verify APOB_NV is working
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: I0f710f12cc5d933a75840dbce1c4bad0c2ea04cc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76162
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Updating some submodule pointers to their latest commit causes some
builds with default configuration to fail since all required components
don't fit into 2MB anymore. Specifically, this has been experienced with
the microcode and FSP submodules.
So, increase the default CBFS size to 4MB to make sure builds succeed
with updated submodules.
Change-Id: I2fc16240bef36c057608acadf3cb7c65e7f0d244
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76217
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Set tcc_offset value to 20 in chipset for Thermal Control
Circuit (TCC) activation feature for meteorlake silicon.
Also, remove tcc_offset default value from rex baseboard
and variants.
BUG=b:270664854
BRANCH=None
TEST=Build FW and test on rex board
Change-Id: Ieec1b7e0873eef46a56e612ed1d9445019b1f4a9
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76232
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Use IOMMU_CAP_BASE_[LO,HI] instead of magic values.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I7032d9f032a22649951ef1535f39b918eb8bd539
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76223
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ie155cab1f659e9f7b64cd87ba8a77260056656d8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76222
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Phoenix is an x86 soc that supports sha256 instructions.
TEST=boot birman to chromeos
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: Id228399ba02708b97110d524ce12c2626588762d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76166
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Move this function to the root Makefile.inc since other Makefiles use
the exact same function call. Will allow for deduplication in AMD SoC
Makefiles in a follow-on commit.
Change-Id: I56a50e21b27a4cd6ce1a08a3aea338c63322a6b2
Signed-off-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76167
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The dimm_num shall be dimm, not channel.
BUG=b:288520486
TEST=In kernel, see output from `dmidecode -t 17`.
Observe that Locator reflects proper location of the module.
Change-Id: Id876a5c245ed1a145c930b3456830d7b42780b74
Signed-off-by: Konrad Adamczyk <konrada@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76108
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
In mtl, there is no MAILBOX_BIOS_CMD_TCSS_DEVEN_INTERFACE
So, this patch removes unused code related to
MAILBOX_BIOS_CMD_TCSS_DEVEN_INTERFACE
ADL also removes this code, see cl:62861
BUG=b:288976547
TEST=Tested on Screebo and DP/USB are working as expected after suspend/resume
Change-Id: I5a4b26c38ec3f5fe1d81fd70f8c2196d0e5b84c3
Signed-off-by: Kane Chen <kane.chen@intel.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76126
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch adds CPU ID for C0 stepping (aka QS).
DOC=#723567
TEST=Able to boot on C0 rvp (and rex) and get correct CPU Name in coreboot log.
Change-Id: I53e3b197f2a0090e178877c1eef783b41670ca83
Signed-off-by: Musse Abdullahi <musse.abdullahi@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76135
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
ALL_MONITOR_OFF command is sent using DPOF.
TBT controller needs to be notified about ALL_MONITOR_OFF(TBT Displays OFF) only when Firmware Connection Manager(FWCM) is in use during S0ix Entry/Exit. When configured for SWCM this command should not be sent.
BUG=b:288536417
TEST= Build and boot Rex Proto-1. Verify S0ix working.
Signed-off-by: Usha P <usha.p@intel.com>
Change-Id: I110fb971846f110e7d93a524ceda3bf4bfc15c13
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75717
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Utkarsh H Patel <utkarsh.h.patel@intel.corp-partner.google.com>
Reviewed-by: Jamie Ryu <jamie.m.ryu@intel.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
When probing the resource with the IOMMU_IOAPIC_IDX index, we need to
use the PCI device 0 function 0 on the first bus in the domain for
probing and not the domain device, since the resource isn't on the
domain device, but on the northbridge device which is B0F0D0 in the case
of the APUs.
TEST=This fixes the following error on Mandolin with Picasso:
AMD-Vi: [Firmware Bug]: : IOAPIC[1] not in IVRS table
AMD-Vi: Disabling interrupt remapping
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Id88f17d68ba5accef6561837478828bd3d24baa5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76117
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Don't rely on vendorcode to set enable bit on IOMMU.
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Signed-off-by: Naresh Solanki <Naresh.Solanki@9elements.com>
Change-Id: I1805a20656b7fb3915f8cc93c618ee074461840f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75829
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Print crashlog size information in hex to be consistent with
other prints.
BUG=b:262501347
TEST=Values printed in hex.
Signed-off-by: Pratikkumar Prajapati <pratikkumar.v.prajapati@intel.com>
Change-Id: Ieb5498e702497bfbc2b4d5396d5b760a0010f5de
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75910
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Zero-initialize the ivhd_range and ivhd_entry structs to make sure that
the whole struct is in a defined state.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Iccacc89bfc497449ad0716a3436949505b65f748
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76079
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
To determine the length parameter of memset, use sizeof with the
instance as argument instead of the type. The behavior is the same, but
it clarifies parameters in the memset call a bit.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I63674fbed7097a583cd77fa6e700652d6dcc5565
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76078
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Assign the current address casted to acpi_ivrs_ivhd[11,40]_t pointer to
*ivhd_[11,40] at the beginning of acpi_fill_ivrs[11,40] and then use
memset on *ivhd_[11,40] to zero-initialize the structs.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I70b12fee99d6c71318189ac35e615589a4c8c629
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76077
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
No matter what DRAM calibration is performed, DRAM scramble should be
enabled as long as MEDIATEK_DRAM_SCRAMBLE is set to y. Currently, DRAM
scramble is enabled only if full calibration is performed. Correct the
behavior by adding DRAMC_CONFIG_SCRAMBLE to the header config in fast
calibration flow.
BUG=b:285474337
TEST=Check the scramble feature is disabled on serial build
Signed-off-by: Xi Chen <xixi.chen@mediatek.corp-partner.google.com>
Change-Id: I907bccd4e68e040179e1971db6bf7a57b88dec1b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75818
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Zero-initialize the ivhd_hpet struct right at the beginning of the
ivhd_describe_hpet function to make sure that the whole struct is in a
defined state.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: If4d3563c485eed4a7cb0526a62f7b6c80f763bfd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76074
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Allow the caller to specify the HID that gets written to the
ivrs_ivhd_f0_entry_t struct.
TEST=None
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I830f1fbbd535b100c88997ece10142a5d553950f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76073
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
Zero-initialize the ivhd_f0 struct right at the beginning of the
ivhd_describe_f0_device function to make sure that the whole struct is
in a defined state.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ia6750b58dacb9b9192ed21128eb6e3a4495b96d0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76072
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Jason Glenesk <jason.glenesk@gmail.com>
The eMMC entry in the IVRS table should only be generated if an eMMC
controller is present in the SoC.
Where the PCI_DEVFN(0x13, 1) is from is currently unclear to me. There
is no PCI device 0x13 on bus 0 and the eMMC controller is also an MMIO
device and not a PCI device, but this is what the reference code does.
My guess would be that it mainly needs to be a unique PCI device that
won't collide with any existing PCI device in the SoC. Add a comment
about this too.
TEST=None
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I00865cb7caf82547e89eb5e77817e3d8ca5d35dd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75933
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Commit d054bbd4f1 ("Makefile.inc: fix multiple jobs build issue")
added a dependency on $(obj)/fmap_config.h to all .c source files in all
stages, so it's not needed any more to add it as a dependency to files
that include fmap_config.h.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I7b62917f32ae9f51f079b243a606e5db07ca9099
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76002
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Add JSL SKUs ID and add PLx from JSL PDG in project devicetree.
BUG=b:281479111
TEST=emerge-dedede coreboot and read correct value on dibbi
Signed-off-by: Chia-Ling Hou <chia-ling.hou@intel.com>
Change-Id: Ic086e32a2692f4f5f9b661585b216fa207fc56fd
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75679
Reviewed-by: Super Ni <super.ni@intel.corp-partner.google.com>
Reviewed-by: Super Ni <super.ni@intel.com>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
The prefix POSTCODE makes it clear that the macro is a post code.
Hence, replace related macros starting with POST to POSTCODE and
also replace every instance the macros are invoked with the new
name.
The files was changed by running the following bash script from the
top level directory.
sed -i'' '30,${s/#define POST/#define POSTCODE/g;}' \
src/commonlib/include/commonlib/console/post_codes.h;
myArray=`grep -e "^#define POSTCODE_" \
src/commonlib/include/commonlib/console/post_codes.h | \
grep -v "POST_CODES_H" | tr '\t' ' ' | cut -d ' ' -f 2`;
for str in ${myArray[@]}; do
splitstr=`echo $str | cut -d '_' -f2-`
grep -r POST_$splitstr src | \
cut -d ':' -f 1 | xargs sed -i'' -e "s/POST_$splitstr/$str/g";
grep -r "POST_$splitstr" util/cbfstool | \
cut -d ':' -f 1 | xargs sed -i'' -e "s/POST_$splitstr/$str/g";
done
Change-Id: I25db79fa15f032c08678f66d86c10c928b7de9b8
Signed-off-by: lilacious <yuchenhe126@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/76043
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Rename shared SRAM aliases for IOE and PMC to make them more readable.
pci device 13.3 is IOE shared sram, renamed to ioe_shared_sram.
pci device 14.2 is PMC shared sram, renamed to pmc_shared_sram.
Rename them in SOC code as well as mainboard to make sure the patch
builds for the relevant boards.
BUG=b:262501347
TEST=Able to build.
Signed-off-by: Pratikkumar Prajapati <pratikkumar.v.prajapati@intel.com>
Change-Id: I02a8cacc075f396549703d7a008382e76258f865
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75999
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch introduces a newer config to store the CSE RW FW version into
the CBMEM. Prior to that CSE RW FW version was fetched unconditionally
and ended up increasing the boot time by 7ms to 20ms depending on the
SoC arch (including CSE arch).
The way to retrieve the CSE firmware version is by sending the HECI
command to read the CSE Boot Partition (BP) info. The cost of sending
HECI command to read the CSE FW version is between 7ms-20ms (depending
on the SoC architecture) hence,ensure this feature is platform specific
and only enabled for the platformthat would like to store the CSE version into the CBMEM.
TEST=Build and boot google/rex to avoid getting CSE RW FW version
to save 18ms of the boot time.
w/o this patch:
10:start of ramstage 722,215 (43)
17:starting LZ4 decompress (ignore for x86) 741,415 (19,200)
w/ this patch:
10:start of ramstage 722,257 (43)
17:starting LZ4 decompress (ignore for x86) 723,777 (1,520)
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I94f9f0f99706724c7d7e05668390f3deb603bd32
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75998
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Dinesh Gehlot <digehlot@google.com>
The patch adds a possibility to cache the PCIe 5.0 HSPHY firmware in
the SPI flash. New flashmap region is created for that purpose. The
goal of caching is to reduce the dependency on CSME and the HECI IP
LOAD command which may fail when the CSME is disabled, e.g. soft
disabled by HECI command or HAP disabled. This change allows to
keep PCIe 5.0 root ports functioning even if CSME/HECI is not
functional.
TEST=Boot Ubuntu 22.04 on MSI PRO Z690-A and notice PCIe 5.0 port
is functional after loading the HSPHY from cache.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I5a37f5b06706ff30d92f60f1bf5dc900edbde96f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68987
Reviewed-by: Krystian Hebel <krystian.hebel@3mdeb.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In order to clean up the post code macros, move them to a separate
header away from unrelated code. The new header file is included in
the file where the post codes are moved out of, so that the current
state remains unchanged.
Change-Id: I28a932ce071488e90000e1bbd30b4d739a4bae43
Signed-off-by: lilacious <yuchenhe126@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75809
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Make the default MEDIATEK_DRAM_SCRAMBLE value overridable by adding a
prompt string.
BUG=b:285474337
TEST=build pass and check scramble feature is disabled on serial build
Signed-off-by: Xi Chen <xixi.chen@mediatek.corp-partner.google.com>
Change-Id: I703ac9aa3ccc4dd9d0fef9949c6b0d49449971a4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75815
Reviewed-by: Yidi Lin <yidilin@google.com>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch renames config `SOC_INTEL_METEORLAKE_U_P` to
`SOC_INTEL_METEORLAKE_U_H` as per Intel Meteor Lake Processor EDS
version 1.3.1 (doc number: 640228).
With new branding, the MTL-U/H-Processor Line offered in a 1-chip platform that includes the Compute, SOC, GT, and IOE tile on the
same package.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I032be650bbfef0bf0ef86bb37417b1d854303501
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75931
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
Using the boolean type and the true/false macros give the reader a
better understanding about the option. Thus, use the bool type for the
attribute and use the macros for assignments.
Skylake mainboards which use that option were changed by the following
command ran from the root directory.
socs="SOC_INTEL_(SKYLAKE|KABYLAKE|SKYLAKE_LGA1151_V2)" && \
option="s0ix_enable" && \
grep -Er "${socs}" src/mainboard | \
cut -d ':' -f 1 | \
awk -F '[/]' '{print $1"/"$2"/"$3"/"$4}' | \
xargs grep -r "${option}" | \
cut -d ':' -f 1 | \
xargs sed -i'' -e "s/${option}\".*\=.*\"1\"/${option}\" \= true/g"
Change-Id: I372dfb65e6bbfc79c3f036ce34bc399875d5ff16
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75871
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Enable early caching of the TOM region to optimize the boot time by
selecting `SOC_INTEL_COMMON_BASECODE_RAMTOP` config.
Purpose of this feature is to cache the TOM (with a fixed size of
16MB) for all consecutive boots even before calling into the FSP.
Otherwise, this range remains un-cached until postcar boot stage
updates the MTRR programming. FSP-M and late romstage uses this
uncached TOM range for various purposes (like relocating services
between SPI mapped cached memory to DRAM based uncache memory) hence
having the ability to cache this range beforehand would help to
optimize the boot time (more than 50ms as applicable).
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I579f85e84e0aba7f192ff81a6725d65b7f79ff75
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74517
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch adds a new Kconfig that controls whether CBFS APIs for
unverified areas will allow file decompression when CBFS verification is
enabled. This should be disallowed by default because it exposes the
attack surface of all supported decompression algorithms. Make
allowances for one legacy use case with CONFIG_SOC_INTEL_CSE_LITE_
COMPRESS_ME_RW that should become obsolete with VBOOT_CBFS_INTEGRATION.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ieae420f51cbc01dae2ab265414219cc9c288087b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75457
Reviewed-by: Jakub Czapiga <jacz@semihalf.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yu-Ping Wu <yupingso@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
For a unification of the naming convension, change from pascal case to
snake case style for parameter 'SataPwrOptimizeDisable'.
Change-Id: I35b36f60d2f00bfad307dff7bd131c20ebccf60b
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75859
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
For a unification of the naming convension, change from pascal case to
snake case style for parameter 'DisableSataSalpSupport'.
Change-Id: I4a68ffd2b68c92434da681b5e5567329c8784c72
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75858
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
For a unification of the naming convension, change from pascal case to
snake case style for parameter 'PmicVdd2Voltage'.
Change-Id: I179b8f5b56c5bfe7f6fc3148e4c95954c0755ffd
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75857
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
For a unification of the naming convension, change from pascal case to
snake case style for parameter 'ModPhyVoltageBump'.
Change-Id: Ic1e743e23bdfc45588411c584eecb839cc552faf
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75856
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
For a unification of the naming convension, change from pascal case to
snake case style for parameter 'ModPhyIfValue'.
Change-Id: I4cdf68e65cea4ab316af969cd6a8d096b456518d
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75855
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
For a unification of the naming convension, change from pascal case to
snake case style for parameter 'DisableComplianceMode'.
Change-Id: I9d5605134a753f161a66857c7f78844ae7490cd6
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75854
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
For a unification of the naming convension, change from pascal case to
snake case style for parameter 'PmicPmcIpcCtrl'.
Change-Id: I3632d1e83108221d3487b4f175133ad347238bc5
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75853
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
For a unification of the naming convension, change from pascal case to
snake case style for parameter 'SataPortsHotPlug'.
Change-Id: I8fc8b30ac2c182ffaf2dee37e0116e27071b6a2c
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75852
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
With commit f165bbdcf0 ("soc/intel/apollolake: Make SATA speed limit
configurable") came the expansion to adjust the SATA speed.
Unfortunately, APL FSP-S sets only the default value, so Gen 3, and
ignores the passing parameter value. Since the corresponding register
entry can only be changed once, the setting must be made on coreboot
side before FSP-S is called. This patch fixes the SATA speed
configuration for Apollo Lake CPUs.
Link to Intel Pentium and Celeron N- and J- series datasheet volume 2:
https://web.archive.org/web/20230614130311/https://www.intel.com/content/www/us/en/content-details/334818/intel-pentium-and-celeron-processor-n-and-j-series-datasheet-volume-2.html
BUG=none
TEST=Boot into Linux and check SATA configuration via dmesg
ahci 0000:00:12.0: AHCI 0001.0301 32 slots 1 ports 3 Gbps 0x1 impl SATA
mode
ata1: SATA max UDMA/133 abar m2048@0x9872a000 port 0x9872a100 irq 126
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
Change-Id: I6f55f40941fa618e7de13a5cefe9e17ae34c5c99
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75820
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
TCSS and TBT use the same lane on schematic. Update the port start
from 0 to match the Intel schematic. You can better follow the it
without convert the port number.
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: Ic6631dcbbd9f6c79c756b015425e2da778eb395e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75892
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Add following config options.
1. TME_GENERATE_NEW_KEY_ON_WARM_BOOT
Program Intel TME to generate a new key for each warm boot. TME
always generates a new key on each cold boot. With this option
enabled TME generates a new key even in warm boot. Without this
option TME reuses the key for warm boot.
2. TME_EXCLUDE_CBMEM_ENCRYPTION
This option allows to exclude the CBMEM region from being encrypted
by Intel TME. When TME is enabled it encrypts whole DRAM. TME
provides option to carve out a region of physical memory to get
excluded from encryption. With this config enabled, CBMEM region
does not get encrypted by TME. If TME is not programmed to generate
a new key in warm boot, exclusion range does not need be programmed
due to the fact that TME uses same key in warm boot if
TME_GENERATE_NEW_KEY_ON_WARM_BOOT is not set. But if TME is
programmed to generate a new key in warm boot, contents of the CBMEM
get encrypted with a new key in each warm boot case hence, that leads
to loss of CBMEM data from previous warm boot. So enabling this
config allows CBMEM region to get excluded from being encrypted and
can be accessible irrespective of the type of the platform reset.
Bug=b:276120526
TEST=Able to build rex
Signed-off-by: Pratikkumar Prajapati <pratikkumar.v.prajapati@intel.com>
Change-Id: Id5008fee07b97faadc7dd585f445295425173782
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75625
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch disables the ACPI PM timer which is necessary for XTAL OSC
shutdown. Also, disabling ACPI PM timer switches off TCO.
BUG=b:274744845
TEST=Able to boot and verify S0ix is working even with EC reset and
cold boot scenarios.
w/o this cl:
> iotools mmio_read32 0xfe4018fc
0x0
w/ this cl:
> iotools mmio_read32 0xfe4018fc
0x2
Change-Id: Ibb6e145f67dba7270e0a322ef414bf1cb09c5eda
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75822
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Certain chipsets/SoCs like Apollo Lake use GEN_PMCON_B for periodic SMI
rate selection unlike other chipsets which use GEN_PMCON_A. Select
PERIODIC_SMI_RATE_SELECTION_IN_GEN_PMCON_B to indicate the register
difference.
Based on Apollo Lake datasheet Vol. 3 Revision 005:
https://cdrdv2.intel.com/v1/dl/getContent/334819
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: If182e1285ad6bd3f7c54760440010c50f57f7013
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72072
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Certain chipsets/SoCs like Apollo Lake use GEN_PMCON_B for periodic SMI
rate selection unlike other chipsets which use GEN_PMCON_A. Introduce new Kconfig option PERIODIC_SMI_RATE_SELECTION_IN_GEN_PMCON_B to
indicate the register difference.
Based on Apollo Lake datasheet Vol. 3 Revision 005:
https://cdrdv2.intel.com/v1/dl/getContent/334819
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: I11241836ecc9066d323977b030686567c87ed256
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69870
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-by: Krystian Hebel <krystian.hebel@3mdeb.com>
This makes sure that the resource allocator won't use this address range
for anything else. In the systems I looked at, this was between the end
of the above 4GB memory and the beginning of the above 4GB PCI BAR MMIO
region, but better reserve it here so nothing else will get allocated
there if this expectation isn't met.
TEST=Reserved region is printed in the console logs:
update_constraints: PCI: 00:00.0 09 base fd00000000 limit fdffffffff mem (fixed)
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I5a8150873cb019ca1d903ed269e18d6f9fabb871
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75611
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This patch reduces the redundant config check to understand if an ISH FW
partition is available and to fetch the ISH FW version.
The goal is to fetch the ISH FW version if the ISH FW belongs to the CSE
firmware partition table.
Change-Id: I689a71377e7aea0fa3bc1835f355708c33c2caea
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75811
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch renames `SOC_INTEL_STORE_CSE_FPT_PARTITION_VERSION` config
to `SOC_INTEL_STORE_ISH_FW_VERSION` to ensure the usage of this config
is clear.
Any platform would like to fetch the currently running ISH firmware
version should select this configuration.
TEST=Able to build and boot google/marasov.
Change-Id: Ie503d6a5bf5bd0d3d561355b592e75b22c910bf5
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75767
Reviewed-by: Kangheui Won <khwon@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Update all the required sources to lay the ground work to enable PSP
verstage.
BUG=b:284984667
TEST=Build Myst BIOS image with PSP verstage enabled.
Change-Id: I6fbb1f835ac2ad6ff47f843321e1bd380af7ce33
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75584
Reviewed-by: Tim Van Patten <timvp@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Alder Lake-S 2+0 SKUs and 35W SKUs have 20A GT TDC, all other Alder
Lake-S SKUs have GT TDC of 22A.
Based on the default settings of ADL-S FSP.
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Change-Id: Ie6851d322fc9354d019a76503c3d35b5e6eca48b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72998
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Krystian Hebel <krystian.hebel@3mdeb.com>
In soc/amd this function is unused so drop it and rename
_acpi_fill_ivrs_ioapic().
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: Ic403fd84cb9cd5805fbc6f0c5a64cefbf4b0cd81
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75711
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Naresh <naresh.solanki.2011@gmail.com>
By adding all DXIO IOAPIC with the same resource index, the IVRS code
can always pick that resource which simplifies the code.
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: I10345e2337dcb709c2c1a8e57a1b7dd9c04adb9e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75710
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Reviewed-by: Naresh <naresh.solanki.2011@gmail.com>
"current" points to the start of HEST table, so "next - current" already
includes the size of its header, no need for increment here. This issue
was found on SPR-SP platform. The length of HEST table is now correct
with this patch.
Change-Id: I6ff1e8e24612b7356772d582ff9a7e53863419db
Signed-off-by: Jeff Li <lijinfeng01@inspur.com>
Signed-off-by: Ziang Wang <ziang.wang@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75738
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Rename get_smee_reserved_address_bits to get_sme_reserved_address_bits
since the feature is called secure memory encryption and the last 'e' in
SMEE bit in the SYSCFG MSR just stands for enable. The function will
return a valid number of reserved address bits no matter if this is
enabled or not, so drop the second 'e'.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I3795f7a861e39cb6c8209fee10191f233cbcd308
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75766
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Currently the data to be put to cache region is 0x14FF90. With the
limit size 0x150000, the data for S3 can not be put into. So we expand
it a little.
Change-Id: If6b03b713059c54c7dae8f2db0f6426d8aa1aab1
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/69782
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The original clock rate 416MHz is insufficient for 4K resolution and
causing the screen to glitch. Set the clock rate to 594MHz to support
4K resolution.
BUG=b:236328487
TEST=Glitching screen was fixed after applying this patch
Change-Id: Ic40dd28264d03ef7218ff4edd8d4182e0fe74ea3
Signed-off-by: Hsiao Chien Sung <shawn.sung@mediatek.com>
Signed-off-by: Jason Chen <Jason-ch.Chen@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75661
Reviewed-by: Yidi Lin <yidilin@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Geralt SoC does not support 'persist certain regions' across reboots.
Considering the impact of missing ramoops for debugging, set
MEDIATEK_DRAM_SCRAMBLE to default n to disable this feature in
production FW image.
BUG=b:269049451,b:278478563
TEST=emerge-geralt coreboot and confirm CONFIG_MEDIATEK_DRAM_SCRAMBLE=n
Signed-off-by: Yidi Lin <yidilin@chromium.org>
Change-Id: I109634d811a928e3e6f7f56e706a5b61a52a21ab
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75562
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Fix a typo in an enum type name, "PIM2_MI" -> "SPIM2_MI".
TEST=emerge-cherry coreboot
Signed-off-by: Yidi Lin <yidilin@chromium.org>
Change-Id: Ib43a044dc69a93ad1dcaa5e65c66a82046a40777
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75726
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
As per AMD64 Architecture Programmer's Manual, section 10.2.5 SMRAM
Protected Areas:
The TSEG range must be aligned to a 128 Kbyte boundary and the minimum
TSEG size is 128 Kbytes.
The SMM TSEG size should be less than SMM reserved size.
AMD TSEG mask works like an MTRR. It needs to be aligned to it's size
and it's size needs to be a power of 2.
Change-Id: Ic4f557c7b77db6fc5ab2783ca4e2ebe7a4476e85
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75405
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Himanshu Sahdev <himanshu.sahdev@intel.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
This commit introduces a refactored version of the IVRS (I/O
Virtualization Reporting Structure) table generation. The main objective
of this refactoring is to generalize the process of generating the IVRS
table based on the IOMMU (Input/Output Memory Management Unit) domains
and their corresponding resources.
Signed-off-by: Naresh Solanki <Naresh.Solanki@9elements.com>
Change-Id: Ic471f05d6000c21081d70495b7dbd4350e68b774
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75451
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The file VGA_BIOS_FILE points to is right now the Mendocino VBIOS. Since
the default value probably shouldn't point to a location in site-local,
drop this for now, but leave a TODO to put that back once the correct
VBIOS files are available in 3rdparty/amd_blobs.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ifbc6cbe1e371d8d247f86555a5361ed237897dea
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75484
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Instead of adding the new PCI IDs of the XHCI controllers in every new
chip generation to the pci_xhci driver, bind the driver to the internal
PCI devices of the XHCI controllers via the device ops statement in the
chipset devicetree. The PCI device function of the XHCI2 controller in
Mendocino can be either a dummy device or the XHCI controller, so the
device ops are attached to that device in the mainboard devicetree
instead. The Glinda code is right now just a copy of the Mendocino code,
so it'll change in the future, but for consistency the equivalent
changes to those in Mendocino are applied there too.
Since the device ops are now attached to the devices via the static
devicetree entry, also remove both the xhci_pci_driver struct and the
amd_pci_device_ids array from drivers/usb/pci_xhci/pci_xhci.c.
TEST=SSDT entries for the XHCI controllers are still generated on
Mandolin.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I9c455002c6d2aac576fe24eee0c31744b4507bb0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75713
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
The PCI root complex itself isn't on an enumerable bus, so without
providing an _STA method, the device will still be assumed to be present
and visible, so this won't change behavior. This also brings Stoneyridge
more in line with the newer SoCs.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I663c7bcba89ffe25d0819d83461cb95e10f49028
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75671
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The PCI root complex itself isn't on an enumerable bus, so without
providing an _STA method, the device will still be assumed to be present
and visible, so this won't change behavior. This also brings Picasso
more in line with Cezanne and newer SoCs.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Suggested-by: Nico Huber <nico.h@gmx.de>
Change-Id: Ied48b48113f6e871e90d17cbd216be003f05b5ef
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74993
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Hook up xhci ops for Phoenix xHCI device. Benefit is we don't have to
bother by adding xhci DID.
BUG=b:285981912
TEST=check coreboot log shows below.
[INFO ] \_SB.PCI0.GP41.XHC0.RHUB.SS01: USB3 Type-A Port A0 (MLB)
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: Ib59874948725966b04b54def3f6de463afeda709
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75659
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Make get_ramtop_addr not static to allow other code to use it.
Bug=b:276120526
TEST=Able to build rex
Signed-off-by: Pratikkumar Prajapati <pratikkumar.v.prajapati@intel.com>
Change-Id: I8ef8a65b93645f25ca5e887342b18679d65e74b4
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75624
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Replace the magic constants by using defines.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I16179a37b6ee19bc3b4862b7dcb3bbc4caf63f2e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75668
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Replace the magic constants by using defines.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I94ad285a2c5712d352d4f92697fc3140847d88de
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75667
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Replace the magic constants by using defines.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I6303e5a697a7ad09a48cb7a2c79fa76f4c6ce232
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75666
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Use the ROOT_BRIDGE macro in soc.asl to replace the pci0.asl file. The
soc/amd/common/acpi/lpc.asl file which was included in the now removed
pci0.asl file now gets included in the correct scope in the soc.asl
file.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I373c171f7f4754391012b41d44965561ced4f0b7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75595
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use the ROOT_BRIDGE macro in soc.asl to replace the pci0.asl file. The
soc/amd/common/acpi/lpc.asl file which was included in the now removed
pci0.asl file now gets included in the correct scope in the soc.asl
file.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: If293188fc8d0ff41b47ab84c9655333e9ebe58e8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75594
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Use the ROOT_BRIDGE macro in soc.asl to replace the pci0.asl file. The
soc/amd/common/acpi/lpc.asl file which was included in the now removed
pci0.asl file now gets included in the correct scope in the soc.asl
file.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I6fc4b09f79e633208ab7536543c876c2c6129eb3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75593
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use the ROOT_BRIDGE macro in soc.asl to replace the pci0.asl file. The
soc/amd/common/acpi/lpc.asl file which was included in the now removed
pci0.asl file now gets included in the correct scope in the soc.asl
file.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ia8f0f1619a71f4ab2051714a9d8c7eb200845390
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75592
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This file only contain the ACPI code describing the MMIO devices in the
FCH, so rename it to mmio.asl. This also brings the Stoneyridge ACPI
code a bit more in line with the ACPI code of the other SoCs.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Iccef1fc5230e3e104d8dea586a9cbaf894471c12
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75597
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Instead of having the different static parts of the PCI0 device in
northbridge.asl and sb_pci0_fch.asl, instantiate the static parts of the
PCI0 device via the ROOT_BRIDGE macro in soc.asl.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I4a9af2fd853f4e993e71158c5e85052084b50cdc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75596
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
This file only contain the ACPI code describing the MMIO devices in the
FCH, so rename it to mmio.asl. This also brings the Picasso ACPI code a
bit more in line with the ACPI code of the newer SoCs.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I64490ba8e34ae1fbe6aea1ab6496b5b04ac4d0aa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75591
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Instead of having the different static parts of the PCI0 device in
northbridge.asl and sb_pci0_fch.asl, instantiate the static parts of the
PCI0 device via the ROOT_BRIDGE macro in soc.asl.
TEST=Both Ubuntu 2022.4 and Windows 10 still boot successfully and don't
show any new ACPI-related error.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I2587d8bb270dc3edce9dfa570a5018116fc9187f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75569
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
When instantiated in the DSDT, this macro will expand to the static part
of the PCIe root bridge device. This macro allows both to deduplicate
parts of the DSDT code as well as adding more than one PCIe root bridge
device in the DSDT.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: I6f20d694bc86da3c3c9c00fb10eecdaed1f666a8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75568
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Now that Stoneyridge is the only AMD SoC that still needs the part of
the SSDT that contains the TOM1 and TOM2, move it from the common code
to the Stoneyridge northbridge code.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I9091360d6a82183092ef75417ad652523babe075
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75564
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Use the new common AMD code that gets the usable non-fixed MMIO windows
from the data fabric MMIO decode registers and generate the PCI0 _CRS
ACPI code based on those regions. For a more detailed description see
the corresponding patch that changes the Picasso code to use this new
code. In contrast to the Picasso code, this change will drop the
unneeded _STA method inside the PCI0 scope which wasn't present in
Picasso's ACPI code before it got replaced by the SSDT that gets
generated by amd_pci_domain_fill_ssdt.
TEST=None
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I948d882b2e2c6d19f73c0be094e4ff6e42ec81d6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75560
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Use the new common AMD code that gets the usable non-fixed MMIO windows
from the data fabric MMIO decode registers and generate the PCI0 _CRS
ACPI code based on those regions. For a more detailed description see
the corresponding patch that changes the Picasso code to use this new
code. In contrast to the Picasso code, this change will drop the
unneeded _STA method inside the PCI0 scope which wasn't present in
Picasso's ACPI code before it got replaced by the SSDT that gets
generated by amd_pci_domain_fill_ssdt.
BUG=b:283495475
TEST=Myst still boots and both the coreboot console and the kernel show
the expected PCI MMIO ranges being used.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I425876c4ef470574e00e123d36101641240c98cf
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75559
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Use the new common AMD code that gets the usable non-fixed MMIO windows
from the data fabric MMIO decode registers and generate the PCI0 _CRS
ACPI code based on those regions. For a more detailed description see
the corresponding patch that changes the Picasso code to use this new
code. In contrast to the Picasso code, this change will drop the
unneeded _STA method inside the PCI0 scope which wasn't present in
Picasso's ACPI code before it got replaced by the SSDT that gets
generated by amd_pci_domain_fill_ssdt.
TEST=None
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Iad34d74d9f6cbed1d8a71a561a505f563e31db18
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75558
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Use the new common AMD code that gets the usable non-fixed MMIO windows
from the data fabric MMIO decode registers and generate the PCI0 _CRS
ACPI code based on those regions. For a more detailed description see
the corresponding patch that changes the Picasso code to use this new
code. In contrast to the Picasso code, this change will drop the
unneeded _STA method inside the PCI0 scope which wasn't present in
Picasso's ACPI code before it got replaced by the SSDT that gets
generated by amd_pci_domain_fill_ssdt.
TEST=None
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I7b14ee0682ae1f2212ab43977c076687706434ec
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75557
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Instead of having PCI0's _BBN method in the DSDT that always returns 0,
use acpigen_write_BBN to generate the _BBN method that returns the first
PCI bus number in the PCI domain/host bridge.
TEST=On mandolin the _BBN method in the _SB/PCI0 scope is now in the
SSDT instead of the DSDT, but still returns 0.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I8badeb0064b498d3f18217ea24bff73676913b02
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74992
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use amd_pci_domain_read_resources function that gets the configured MMIO
regions for the PCI root domain from the data fabric's MMIO decode
registers instead of using pci_domain_read_resources. This results in
the same IO port range being used by the allocator, but makes sure that
the allocator will only allocate non-fixed MMIO resources in the address
ranges that get decoded to the PCI root complex. In order for the PCI0
_CRS ACPI resource template to match the decoded PCI root domain MMIO
windows, use amd_pci_domain_fill_ssdt to generate the _CRS ACPI code
instead of having a mostly hard-coded _CRS method in the DSDT. This
makes sure that the OS will know about the MMIO regions it is allowed to
used.
Before this patch, only the region from TOM1 to right below
CONFIG_ECAM_MMCONF_BASE_ADDRESS was advertised as usable PCI MMIO in the
PCI0 _CRS method. Also the resource allocator didn't get any constraint
on which address ranges it can use to put the non-fixed MMIO resources.
This approach worked until now, since all address range from 0 up to
right below TOM1 was filled with either usable or reserved memory and
the allocator was allocating beginning right from TOM1, since it was
using the bottom-up allocation approach and everything below TOM1 was
already in use. The MMIO region from TOM1 to right below
CONFIG_ECAM_MMCONF_BASE_ADDRESS also matched the MMIO decode window
configured in the data fabric's MMIO decode registers, so everything
seemed to work fine. However, when either selecting
RESOURCE_ALLOCATION_TOP_DOWN or enabling above 4GB MMIO, things broke
badly. This was partially due to the allocator putting non-fixed MMIO
resources in regions that weren't decoded to the PCI root, since AMD
family 17h and 19h silicon doesn't subtractively decode PCI MMIO and the
wrong ranges the allocator used also weren't advertised in ACPI.
TEST=Even when selecting RESOURCE_ALLOCATION_TOP_DOWN that usually ends
up with a non-working system when the MMIO ranges aren't reported
correctly to the resource allocator due to the reasons descried above,
Ubuntu 22.04 LTS still boots on Mandolin both with SeaBIOS and EDK2
payload and Windows 10 boots with EDK payload. There's however an EDK2
bug that results the MMCONFIG region not being advertised in the e820
table, which causes Linux to not use the MMCONFIG and fall back to the
legacy PCI config access method. This only happens with EDK2 payload and
everything works fine when using SeaBIOS as payload. That e820 issue is
unaffected by this patch.
At the end of the data_fabric_set_mmio_np call, this is the data fabric
MMIO register configuration:
=== Data Fabric MMIO configuration registers ===
idx base limit control R W NP F-ID
0 fc000000 febfffff 93 x x 9
1 10000000000 ffffffffffff 93 x x 9
2 d0000000 f7ffffff 93 x x 9
3 fed00000 fedfffff 1093 x x x 9
4 0 ffff 90 9
5 0 ffff 90 9
6 0 ffff 90 9
7 0 ffff 90 9
The limit of the data fabric MMIO decode register 1 is configured as
0xffffffffffff although this is way beyond the addressable memory space.
add_data_fabric_mmio_regions fixes this up, so the range that gets
passed to the allocator in that case is 0x7fcffffffff which takes both
the reserved most significant address bits used for the memory
encryption and the 12GB reserved data fabric MMIO at the top of the
usable address space into account.
This results in the following domain ranges passed to the resource
allocator:
DOMAIN: 0000 io: base: 0 size: 0 align: 0 gran: 0 limit: ffff done
DOMAIN: 0000 mem: base: fc000000 size: 0 align: 0 gran: 0 limit: febfffff
DOMAIN: 0000 mem: base: 10000000000 size: 0 align: 0 gran: 0 limit: 7fcffffffff
DOMAIN: 0000 mem: base: d0000000 size: 0 align: 0 gran: 0 limit: f7ffffff
The IO resource producer region is split into two parts to not cover the
PCI config IO region resource consumer. This results in these resources
being added to the PCI0 _CRS resource template:
amd_pci_domain_fill_ssdt ACPI scope: '\_SB.PCI0'
PCI0 _CRS: adding busses [0-3f]
PCI0 _CRS: adding IO range [0-cf7]
PCI0 _CRS: adding IO range [d00-ffff]
PCI0 _CRS: adding MMIO range [fc000000-febfffff]
PCI0 _CRS: adding MMIO range [10000000000-7fcffffffff]
PCI0 _CRS: adding MMIO range [d0000000-f7ffffff]
PCI0 _CRS: adding VGA resource
Kernel version 5.15.0-43 from Ubuntu 2022.4 LTS prints this in dmesg:
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [bus 00-3f]
pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7 window]
pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window]
pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
pci_bus 0000:00: root bus resource [mem 0xd0000000-0xf7ffffff window]
pci_bus 0000:00: root bus resource [mem 0xfc000000-0xfebfffff window]
pci_bus 0000:00: root bus resource [mem 0x10000000000-0x7fcffffffff window]
Another noteworthy thing I wasn't aware of at first when testing ACPI
changes on Windows 10 is that a normal Windows shutdown and boot cycle
won't result in it processing the changed ACPI tables; you have to tell
it to reboot to do a proper full boot where it will process the updated
ACPI tables (and fail if it dislikes something about the ACPI tables and
bytecode).
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ia24930ec2a9962dd15e874e9defea441cffae9f2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74712
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Generate the PCI0 _CRS ACPI resource template to tell the OS which PCI
bus numbers and IO and MMIO regions can be used for PCI devices below
_SB/PCI0. This data corresponds to what amd_pci_domain_scan_bus and
amd_pci_domain_read_resources provided to the resource allocator. This
makes sure that the PCI0 _CRS ACPI resource template matches the
constraints the resource allocator used when allocating resources.
TEST=With also the rest of the current patch train applied, the
generated _CRS resource template contains the expected PCI bus numbers
and IO and MMIO resources and both Linux and Windows boot on Mandolin.
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Iaf6d38a8ef5bb0163c4d1c021bf892c323d9a448
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74843
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Provide amd_pci_domain_scan_bus to enumerate the PCI buses in the one
PCI root domain and amd_pci_domain_read_resources to read the MMIO
regions that the resource allocator can use to allocate the PCI MMIO
BARs in the one PCI root domain from the corresponding data fabric MMIO
decode registers. This makes sure that the allocator will only put PCI
MMIO resources in areas that are decoded to the PCIe root complex. The
current code only covers the case of a system with one PCI root where
all PCI bus numbers belong to the only PCI root, all IO ports get
decoded to the only PCI root and the MMIO regions from the data fabric
MMIO decode registers get decoded to the only PCI root. In future
patches, this will be extended to also support the multi PCI root case.
TEST=With also the rest of the current patch train applied, the resource
allocator uses the constraints on the MMIO regions and both Linux and
Windows boot on Mandolin.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: I4aada7c8a2a43145ad08d11d0a38d9cdc182b98e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74717
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In case the secure memory encryption is enabled, some of the upper
usable address bits of the host can't be used any more. Bits 11..6 in
CPUID_EBX_MEM_ENCRYPT indicate how many of the address bits are taken
away from the usable address bits in the case the secure memory
encryption is enabled.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ia810b0984972216095da2ad8f9c19e37684f2a2e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75623
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Intel Meteor Lake SOC has a separate I/O Expander (IOE) die.
SRAM from this IOE die contains crashlog records for the IPs
of the IOE die.
This patch adds functions with empty implementation using
__weak attribute for IOE die related crashlog, changes common
data structures while maintaining backwards compatibility,
and support for filling IOE crashlog records, guarded by
SOC_INTEL_IOE_DIE_SUPPORT config and makes cl_get_pmc_sram_data
function as weak because it needs SOC specific implementation.
Bug=b:262501347
TEST=Able to build. With Meteor Lake SOC related patch, able to
capture and decode crashlog
Change-Id: Id90cf0095258c4f7003e4c5f2564bb763e687b75
Signed-off-by: Pratikkumar Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75475
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This makes sure that the resource allocator won't use those ports for
anything else.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I014ffe3ee94ec153e91113f9a17e89f24ca040b3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75619
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
This makes sure that the resource allocator won't use those ports for
anything else.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ie42260902ee2b383dd5867ac813cae029f706f2d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75556
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
This commit adds a configuration option to enable RMT in the coreboot
build for the Intel Xeon SP SPR platform.
Signed-off-by: Naresh Solanki <Naresh.Solanki@9elements.com>
Change-Id: I9b9276116c22cfbbec132d7a1b0026a52a51398a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75416
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Based on the power sequence of the panel [1], the power on T2 sequence
VSP to VSN should be larger than 1ms, and the power off T2 sequence VSP
to VSN should be larger than 0ms. We modify the power sequence to meet
the datasheet requirement.
[1] B5 TV110C9M-LL0 Product Specification Rev.P0
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Change-Id: I4ccb5be04062a0516f84a054ff3f40afbf5279be
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75512
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Yidi Lin <yidilin@google.com>
Follow 57263_FP8_MBDG_rev_0_92 Table.57 to update the alias. We
can match the schematic for now.
BUG=b:285793461
TEST=USB still works.
Signed-off-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Change-Id: Id1058279fe5b0e3131608a0b9bbd708dbbde7e87
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75615
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ivy Jian <ivy.jian@quanta.corp-partner.google.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Jon Murphy <jpmurphy@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
This adds printing content of 'manifest' file at ramstage.
It allows to learn about blobs version used to build the coreboot
binary, which is useful when investigating bugs.
Version data are stored in CBFS file, which was generated during
coreboot build. If AMD FW blobs will be manually replaced in coreboot
image, versions from CBFS file are no longer valid.
Log:
AMDFW blobs version:
type: 0x01 ver:00.3c.01.18
type: 0x08 ver:00.5a.28.00
type: 0x30 ver:2b.25.b0.10
type: 0x73 ver:00.3c.01.18
BUG=b:224780134
TEST=Tested on Skyrim device
Change-Id: I8df54b74cd987b4a3be635932d38ea178d0b0311
Signed-off-by: Grzegorz Bernacki <bernacki@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74269
Reviewed-by: Himanshu Sahdev <himanshu.sahdev@intel.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The code is supposed to output debug messages but is commented out, so
do the same for variables.
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Change-Id: Ief1f9d2175fe1375fe6ac4bb0765b00513321fa6
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75356
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
To support the localized text, we need to get the locale id by vboot
APIs and read raw string content file: preram_locales located at either
RO or RW.
The preram_locales file follows the format:
[string_name_1] [\x00]
[locale_id_1] [\x00] [localized_string_1] [\x00]
[locale_id_2] [\x00] [localized_string_2] ...
[string_name_2] [\x00] ...
This code will search for the correct localized string that its string
name is `memory_training_desc` and its locale ID matches the ID vb2api
returns. If no valid string found, we will try to display in English
(locale ID 0).
BUG=b:264666392
BRANCH=brya
TEST=emerge-brya coreboot chromeos-bmpblk chromeos-bootimage
Change-Id: I7e3c8d103c938a11b397c32c9228e44e31c3f01d
Signed-off-by: Hsuan Ting Chen <roccochen@chromium.org>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75330
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
This patch ensures to update the FSP-M UPDs related to PCIe RP mask
properly as per the SoC type.
For example: PCIe RPs belong to the SoC/IOE die for MTL-U/P whereelse
PCIe RPs are from PCH die in case of MTL-S.
BUG=b:276697173
TEST=Able to build and boot google/rex.
Change-Id: Ice81553274682476bb4c927061b1196dc142836d
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75608
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
This patch introduces the different SoC flavors of Intel Meteor Lake as:
* MTL-U
* MTL-P
* MTL-S
MTL-U and MTL-P are PCH less designs, while MTL-S is with PCH die.
The task for mainboard is to specify the correct SoC type rather than
selecting the MTL SoC by default.
This change is necessary to support the different SoC flavors of Intel
Meteor Lake.
BUG=b:276697173
TEST=Able to build and boot google/rex.
Change-Id: I27404bbbd0b489412953118e140f6f39b6e43426
Signed-off-by: Subrata Banik <subratabanik@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75606
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
pci_rom_probe() can allocate memory when mapping a CBFS
file, so pci_rom_free() should be called before leaving
the function.
BUG=b:278264488
TEST=Build and run with additional debug prints added
to confirm that data are correctly unmapped
Change-Id: Ie6fbbfd36f0974551befef4d08423a8148e151e7
Signed-off-by: Grzegorz Bernacki <bernacki@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74779
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Tim Van Patten <timvp@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Himanshu Sahdev <himanshu.sahdev@intel.com>
Move microcode load/unload to pre_mp_init and post_mp_init callbacks.
It allows to make sure that ucode is freed only if all APs updated
microcode.
BUG=b:278264488
TEST=Build and run with additional debug prints added
to confirm that data are correctly unmapped
Change-Id: I200d24df6157cc6d06bade34809faefea9f0090a
Signed-off-by: Grzegorz Bernacki <bernacki@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74777
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
The phoenix SoC does not support multiple EFS locations. Set the default
to the only valid value and prevent mainboard overrides by making the
option non-user-configurable.
TEST=build birman-phoenix
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: I0f720dbadf2d28a3c39daa4bd653a407be4893d0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74249
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
For a unification of the naming convension, change from pascal case to
snake case style for parameter 'SataPortsEnable'.
Change-Id: I0df35125360eb42a03d5445011d72842cb2b8d7e
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75553
Reviewed-by: Himanshu Sahdev <himanshu.sahdev@intel.com>
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Enable early caching of the TOM region to optimize the boot time by
selecting `SOC_INTEL_COMMON_BASECODE_RAMTOP` config.
Purpose of this feature is to cache the TOM (with a fixed size of
16MB) for all consecutive boots even before calling into the FSP.
Otherwise, this range remains un-cached until postcar boot stage
updates the MTRR programming. FSP-M and late romstage uses this
uncached TOM range for various purposes (like relocating services
between SPI mapped cached memory to DRAM based uncache memory) hence
having the ability to cache this range beforehand would help to
optimize the boot time (more than 50ms as applicable).
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Iadbce3124a88cf5be0aebde4a76ec6fd4b670216
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74518
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Intel's APL FSP offers the possibility to select the connected hard
drive type to SATA ports. One has the option to choose between HDD ('0'
- default) and SSD ('1').
This patch provides a chip config so that this FSP parameter can be set
as needed in the devicetree on mainboard level.
Change-Id: I52c3566fb3c959ada6be33f0546ac331f4867d10
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75366
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
In cases where there are limitations on the mainboard it can be
necessary to limit the used SATA speed even though both, the SATA
controller and disk drive support a higher speed rate. The FSP parameter
'SpeedLimit' allows to set the speed limit.
It should be noted that Gen 3 equals the default value '0'. This means
that inside FSP the same code is executed.
This patch provides a chip config so that this FSP parameter can be
set as needed in the devicetree on mainboard level.
Change-Id: I9c3eda0649546e3a40eb24a015b7c6efd8f90e0f
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75364
Reviewed-by: Felix Singer <service+coreboot-gerrit@felixsinger.de>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Check existence of crashlog records in CBMEM before copying them
to BERT, otherwise it can lead to NULL pointer access.
Bug=None
TEST=Able to build. With Meteor Lake SOC related patch, able to
capture and decode crashlog.
Change-Id: I4288011866283a3a5fb8ec9e10cd51b794052b4e
Signed-off-by: Pratikkumar Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75528
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Do not copy the crashlog record if the record is 0xdeadbeef
Bug=None
TEST=Able to build. With Meteor Lake SOC related patch, able to
capture and decode crashlog.
Change-Id: I0edbf6902685a882876d525e63c5b602c1590ea1
Signed-off-by: Pratikkumar Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75527
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Check pmc_record_size variable for collecting PMC records,
instead of cpu_record_size variable.
Bug=None
TEST=Able to build. With Meteor Lake SOC related patch, able to
capture and decode crashlog.
Change-Id: I4c35ba2bcf757231aa2872802eb82d4d50742cd9
Signed-off-by: Pratikkumar Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75526
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
When the default pci_domain_read_resources() is used,
keep 32-bit memory resources below the limit given by
CONFIG_DOMAIN_RESOURCE_32BIT_LIMIT. This serves as a
workaround for missing/wrong reservations of chipset
resources.
This will help to get more stable results from our own
allocator, but is far from a complete solution. Indvi-
dual platform ASL code also needs to be considered, so
the OS won't assign conflicting resources.
Most platforms have reserved space between 0xfe000000
and the 4G barrier. So use that as a global default.
In case of `soc/intel/common/`, use 0xe0000000 because
this is what is advertised in ACPI and there are traces
of resources below 0xfe000000 that are unknown to core-
boot's C code (PCH_PRESERVED_BASE?).
Tested on QEMU/Q35 and Siemens/Chili w/ and w/o top-
down allocation. Fixes EHCI w/ top-down in QEMU.
Change-Id: Iae0d888eebd0ec11a9d6f12975ae24dc32a80d8c
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75102
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The TPS65132S is designed to supply positive/negative driven
application. It communicates through standard I2C compatible interface,
and it intergrates a EEPROM whose contents will be loaded into the
register at startup. Since TPS65132S is used in staryu and geralt
projects, we move the implementation to mediatek/common.
The datasheet: TPS65132-Single-Inductor-Dual-Output-Power-Supply.pdf
BUG=b:282902297
TEST=boot starmie to firmware screen
Signed-off-by: Ruihai Zhou <zhouruihai@huaqin.corp-partner.google.com>
Change-Id: Iad2c9bdea5824455efcef18b44876111061cfa1a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75488
Reviewed-by: Yidi Lin <yidilin@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This brings the ACPI code more in line with both what the new code for
the AMD SoCs will do and also what the current Intel code does. This was
mainly done to have a reduced delta to the new AMD domain resource
handling functions to debug it, but it might still be useful to upstream
this change.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I8cca05976b1c9d4e994e407b8c0197da7dd35eb2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75487
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
cbfs_boot_map_optionrom will generate lower case hex digits for the
filename to look for in CBFS, so make sure that the file name will use
lower case hex digits and no upper case hex digits.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I1d4daa04120de0f2c853a44691b7e2c52eb2af20
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75483
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This commit enables the build for IO Margining, ensuring that ASPM is
disabled and certain FSP knobs are adjusted in coreboot as below
1. Enable DFXEnable
2. Disable PcieGlobalAspm
3. Disable KtiLinkL1En & KtiLinkL0pEn
Since the FSP UPD does not provide all the necessary knobs for IO
Margining, the following settings need to be applied during the FSP
build process:
1. Enable PcdBiosDfxKnobEnabled
2. Disable PchDmiAspm
3. Enable SataTestMode
4. Enable WmphyMargining
5. Disable IioErrorEn
TEST=Build for IBM sbp1 board.
Signed-off-by: Naresh Solanki <Naresh.Solanki@9elements.com>
Change-Id: Ie306d12943adb76411d55358548b5cb2eb3a95be
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75415
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
EFS header is mapped during PSP verstage and bootblock to read some SPI
configuration. After use it is left unmapped. Unmap the EFS region after
use.
BUG=b:240664755
TEST=Build and boot to OS in Skyrim with unsigned PSP verstage.
Change-Id: I865f45a3d25bc639eb8435b54aa80895ec4afd27
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75455
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
cbfs_unmap does not unmap the mapped region from the boot device. This
leads to some resource leaks eg. TLB slots in PSP. Explicitly call
rdev_munmap on the address mapped by cbfs_map.
BUG=b:240664755
TEST=Build and boot to OS in Skyrim with unsigned PSP verstage.
Change-Id: I51b9d066a40103f2ebdf2ef2fc3da13beb467921
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75454
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
cbfs_unmap does not unmap the mapped region from the boot device. This
leads to some resource leaks eg. TLB slots in PSP. Explicitly call
rdev_munmap on the address mapped by cbfs_map.
BUG=b:240664755
TEST=Build and boot to OS in Skyrim with unsigned PSP verstage.
Change-Id: If1d355972cc743b8d8c451e1b3f827abd15e98fe
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75453
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
On FMAP without RW slots, PSP verstage fails to build because of
reference to FMAP_SECTION_FW_MAIN_A_*. Instead extract the offset and
size of relevant sections using fmap_locate_area().
BUG=b:240664755
TEST=Build and boot to OS in Skyrim with unsigned PSP verstage.
Change-Id: I29997534c6843b47a36655431f79e5c70bd17f9b
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75452
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Add support to update power limit values for variants.
Until now, each SoC implements this themselves.
To avoid code duplication, add this to common code.
BRANCH=None
BUG=b:270664854
TEST=Built and verified power limit values as below log message
for 15W SKU on Rex board.
Overriding power limits PL1 (mW) (10000, 15000) PL2 (mW)
(57000, 57000) PL4 (W) (114)
Change-Id: I414715f211d816bbfad03a673ca96dd5df94caeb
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74620
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Hook the SaGvFreq, SaGvGear upds so that mainboard can change the
settings via devicetree. Meteor Lake supports 4 SaGv work points and it
can dynamically scale the work point based on memory bandwidth
utilization. Dynamic gearing technology allows the Memory Controller to
run at 1:1, 1:2 or 1:4 ratio of DRAM speed. The gear ratio is the ratio
of DRAM speed to Memory Controller Clock.
BUG=b:282164577
TEST=Verified the settings on google/rex using debug FSP logs.
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Change-Id: I37169880af4019675374594e90735b5d7d0873b8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75290
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch adds an enum macro to define the different SaGv work points.
The enum macro is named `sagv_wp_bitmap` and it has three values:
The goal is to choose the optimal SaGv work point for the target
platform after considering the two inputs as power consumption and performance. The first group is for workloads that require high performance, even if it means consuming more power. The second group
is for workloads that can tolerate lower performance, in order to save
power.
SAGV_POINTS_0_1: The highest power consumption, but also the highest
performance.
SAGV_POINTS_0_1_2: A lower power consumption than work point
SAGV_POINTS_0_1, but also a lower performance.
SAGV_POINTS_0_1_2_3: The lowest power consumption, but also the lowest
performance.
Set SaGv work points after reviewing the power and performance impact
with SaGv set to 1 (Enabled) and various considering various work points
between 0-3 being enabled.
BUG=b:267879107
TEST=Able to build google/rex.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I4af0038f2799a458d1b006270068341f65d36609
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75362
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add CPU PortID for GPIO communities in order to calculate
IOM Aux Bias data correctly.
BUG=b:283044004
TEST=able to detect external display
Signed-off-by: Marx Wang <marx.wang@intel.com>
Change-Id: I79f27fb0b6bde0a4ce2466eaf707166a952fad81
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75390
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
The data payload size of PCIe root ports can be set to either 128
(default) or 256 bytes. A bigger payload size can improve PCIe data
throughput on the given port. FSP-S provides a parameter to configure
this value.
This patch provides a chip config so that this FSP parameter can be set
as needed in the devicetree on mainboard level.
Change-Id: I5798a72adaa8089dda0b4bc12266b5a235ed4aa3
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75126
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Jan Samek <jan.samek@siemens.com>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
1. Rename set_cmos_mrc_cold_boot_flag() to soc_set_mrc_cold_boot_flag
in case a certain platform may not support this via CMOS data, and
the function could in turn calls mainboard defined method in the
future. Move the code into soc_util.c.
2. Remove redundant static get_system_memory_map() from cpx/romstage.c
and call the soc_util.c one.
Change-Id: Ib7d9bed9092814658f4a0b1d6dcf3c7d79178048
Signed-off-by: Johnny Lin <johnny_lin@wiwynn.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/72029
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Earlier the entire SPI ROM is mapped at the start of verstage and then
unmapped at the end of verstage. With CB:74606, this behavior has
changed. So unmap the hash table CBFS file after usage.
BUG=b:240664755
TEST=Build and boot to OS in Skyrim. Perform cold, warm reboots and
suspend/resume cycles for 50 iterations each. Ensured that there is no
impact to boot time.
Change-Id: I5c605f8ba8bbd571b589b3cdf91e9cc71d711c1c
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75092
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently the SPI ROM is mapped completely when the boot device is
initialized. That mapping remains active throughout the execution time
of PSP verstage. Every 1 MiB of mapped SPI ROM region consumes 1 TLB
Slot in PSP for use during memory mapped or DMA access. With 16 MiB of
mapped SPI ROM + FCH devices + 4 reserved TLB slots, 31 out of 32 total
TLB slots is consumed. This leaves almost no scope for future expansion.
With upcoming programs possibly using 32 MiB SPI ROM, PSP will run out
of TLB slots to support 32 MiB.
Hence instead of mapping the entire SPI ROM upfront, get the SPI ROM SMN
address during the boot device initialization. Update the boot device
region operations to map and unmap the SPI flash with the desired offset
and size using the SVC call. Then anytime a memory mapped SPI ROM access
is performed: map the required area, read the data and immediately unmap
the area. There is no update required when using CCP DMA, since the
concerned SVC call performs mapping and unmapping of the required SPI
flash area implicitly.
With these changes, maximum of 8 slots(size of RO section) might get
used at any point in time during the PSP verstage execution.
BUG=b:240664755
TEST=Build and boot to OS in Skyrim. Perform cold, warm reboots and
suspend/resume cycles for 50 iterations each. Ensured that there is no
impact to boot time.
Change-Id: Icd44ea7b2a366e9269debcab4186d1fc71651db2
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74606
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently unsigned PSP verstage binary is copied from ELF file only when
required in amdfw*.rom. If a signed PSP verstage binary is supplied
while building amdfw*.rom, then it is dropped. Copy the unsigned PSP
verstage binary always so that it can be used for signing directly from
the CI build infrastructure instead of a locally built binary.
BUG=None
TEST=Build Skyrim BIOS image and ensure that the unsigned PSP verstage
is part of the build artifacts.
Change-Id: If797dcfd20aa2991f3517904ef862406b9b9875c
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75334
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Show an error if an option table is used, and the ramtop entry is not
defined on a platform that uses it.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Ie48f0766b29be8e1fb0c1f71c4b2ce6ed20e6207
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74920
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
This patch adds an API to check FSP reset pending requests. This
information is useful to understand if FSP would like boot firmware to
issue any reset to complete the silicon initialization.
As per recent debug it has been found that, FSP is accumulating all
platform resets and executing a single reset from FSP Notify Phase.
As coreboot skipped calling into the FSP Notify APIs hence, it might
have missed the scope to issue the platform reset.
BUG=b:282266168
TEST=Able to build and boot google/rex and able to detect FSP reset
pending request.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ibf7c996f09affa099c9124773fe2d581f370d1a9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75310
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
As announced in the 4.20 release notes, support for the Intel Quark SoC
is moved to the 4.20 branch and dropped from master.
Change-Id: I8a1ca7a2092aaeaea9c72eac5a8dd8f7d72e8f09
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75341
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: ron minnich <rminnich@gmail.com>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
The `ramtop_table` is 10 bytes long, so adjust the check to
account for this.
Also, adjust the wording to make it clear what is required to fix it,
should the error be shown.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: If2898c4bb22abb1779035aadc08f32898e9a096b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74919
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Enable PSYS capability. PSYS is required to safeguard the system
stability if no charger IC.
BUG=b:281479111
TEST=emerge-dedede coreboot chromeos-bootimage & ensure the value is
passed to FSP by enabling FSP log & Boot into the OS
Change-Id: Ibe54acaf80700252558b82f194b9536b6117b84e
Signed-off-by: Chia-Ling Hou <chia-ling.hou@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75196
Reviewed-by: Reka Norman <rekanorman@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add igd device name in soc_acpi_name(), and src/drivers/gfx/generic
can generate device in GFX0 scope in SSDT.
BUG=b:277629750
TEST=emerge-rex coreboot then check SSDT on DUT
Signed-off-by: Won Chung <wonchung@google.com>
Change-Id: Id7a136b5234cf5c0f60ecf253ee78c123f1f573b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75274
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
This patch drops the assert check around
`FSP_MULTIPHASE_SI_INIT_RETURN_BROKEN` config to ensure
`fsp_get_pch_reset_status()` can be used by all other FSP APIs to know
the status of the pending reset.
As per recent debug it has been found that, FSP is accumulating all
platform resets and executing a single reset from FSP Notify Phase.
As coreboot skipped calling into the FSP Notify APIs hence, it might
have missed the scope to issue the platform reset.
Going forward coreboot needs to implement the corresponding logic to be
able to identify any pending platform reset request and execute to
complete the silicon initialization flow.
BUG=b:282266168
TEST=Able to build and boot google/rex.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I2c9e37fadc27eab820a3121e47e09529de34d10e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75309
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The `ramtop` can be obtained from the `option.h`, so remove the
hardcoded value. Keep the check for the value being byte aligned.
Change-Id: I5327b5d4e78b715a85072e5d9a62cf8fd2ae92c0
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74511
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
This patch overrides FSP-S UPD `LogoPtr/LogoSize` with a valid
logo.bmp file if `BMP_LOGO` config is enabled.
TEST=Able to see splash screen while booting google/marasov
with BMP_LOGO config enable.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I421da2b4dadb892f17a859ce0ec586a2880469eb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75294
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch overrides FSP-S UPD `LogoPtr/LogoSize` with a valid
logo.bmp file if `BMP_LOGO` config is enabled.
TEST=Able to see splash screen while booting Intel Meteor Lake RVP
with BMP_LOGO config enable.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Iaba187456dd4dfb2f69d3532e83a3850f31783ed
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75198
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Both the AMD AGESA reference code and the default coreboot
ACPI_CPU_STRING use hexadecimal numbers in the ACPI CPU object names, so
change the ACPI_CPU_STRING format string in the both the Stoneyridge
Kconfig and the common non-CAR AMD SoC config Kconfig which covers all
other AMD SoCs in soc/amd. All platforms where the P state and C state
SSDT from binaryPI (Stoneyridge) or FSP (Picasso) was used in coreboot
before it got replaced by native code, had at most 8 cores/threads, so
the mismatch never became apparent.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I9d6822c5df01786ee541ce90734b75ed1a761fca
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75250
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Set the default soft fuse bits to the recommended values
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: I2354aefe90a08eaef95a68926806d11a9118c3de
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75183
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
In ACPI 1.0 the processor objects were inside the \_PR scope, but since
ACPI 2.0 the \_SB scope can be used for that. Outside of coreboot some
firmwares still used the \_PR scope for a while for legacy ACPI 1.0 OS
compatibility, but apart from that the \_PR scope is deprecated.
coreboot already uses the \_SB scope for the processor devices
everywhere, so move the \_SB scope out of the ACPI_CPU_STRING to the
format string inside the 3 snprintf statements that use the
ACPI_CPU_STRING.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Suggested-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Change-Id: I76f18594a3a623b437a163c270547d3e9618c31a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75167
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Tim Wawrzynczak <inforichland@gmail.com>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Don't set bit 2 of the return value of the _STA method in order for
Windows not to show a warning about an unknown device in the device
manager for this device.
TEST=The unknown device with device instance path ACPI\AMD0040\3
disappeared from the device manager in Windows 10 build 19045 on a
Mandolin board with a Picasso APU.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: If005f06843956004c281fd70cf364171148cb9ff
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68962
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Commit 396fb3db74 ("soc/amd/*/acpi/mmio.asl,sb_fch.asl: hide AAHB
device") didn't only change the visibility of the device, but also
changed the _STA method to a name. While this worked, the specification
says that _STA is supposed to be a method, so change it back to being a
method.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Id0932b2875aaf563a4dbd860bdd11a04272e3780
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75169
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The patch defines enum type for MKHI group IDs and ME SKU types instead
of macros.
TEST=Build code for Rex
Signed-off-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Change-Id: I102e802938a6a664a43a362d90a26755cff8f316
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74996
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Harsha B R <harsha.b.r@intel.com>
Reviewed-by: Anil Kumar K <anil.kumar.k@intel.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Having `_cmos_offset` in a CMOS offset is superfluous; remove it
so the CMOS entry is just `ramtop`.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Ibc1e7d78d2e3ae04330d19e64c3437ff07060ea8
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74516
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
In GEN_PMCON1 (Offset 1020h), Bit 0 is the "After G3 Enable" (ag3e)
(source Intel document #569262). Only use 8 bits, in the same way as
most other Intel SOCs do, for pmc_soc_set_afterg3_en.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: Idb290d1480b03cb3425edc6ff29b9c78a6545df1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74955
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The return value of cse_get_bp_info() is an enum integer, where zero
means success and non-zero means failure. The function
store_cse_rw_fw_version() calls the function cse_get_bp_info() and
validates the return value as a boolean causing prematurely returns of
the parent API even if cse_get_bp_info() is successful.
This patch corrects this logical error by returning only if
cse_get_bp_info() fails.
TEST=Build and boot google/nivviks and verify that the ISH version info
command is only being sent during cold boot.
Signed-off-by: Dinesh Gehlot <digehlot@google.com>
Change-Id: Ice278e5ac69ff2f2c9f1936b76d71ae9deb6f855
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74998
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
If the ME is disabled with the `me_state` CMOS setting, boot
times are approximately 5 seconds longer:
942:before sending EOP to ME 1,240,773 (5,599)
943:after sending EOP to ME 6,263,951 (5,023,177)
Total Time: 6,167,443
This is because the current code only checks if the ME is
disabled for CSE LITE SKUs. With this patch, boot times are
approximately 5 seconds quicker:
Total Time: 1,143,932
Tested on `starbook/adl` and `starbook/tgl`.
Signed-off-by: Sean Rhodes <sean@starlabs.systems>
Change-Id: I182f30d4fbf43955747c6a7a0b284a43f9c5e4ef
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74435
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
This fixes an issue where pcie was not power gating and blocked
S0ix entry. Overwrite pcie max non-snoop and snoop latency tolerance
values to 15.73ms as stated in doc #729123 - MTL External Design
Specification.
BUG=none
TEST=Boot google/rex, print/check values.
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.corp-partner.google.com>
Change-Id: I9dfb9edbac95d28d50653777466ea172be64f612
Reviewed-on: https://review.coreboot.org/c/coreboot/+/68308
Reviewed-by: Jérémy Compostella <jeremy.compostella@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The Intel SoC Meteor Lake requires a higher pcie max non-snoop and
snoop latency tolerance. Add config to let SoC overwrite the common
code settings if needed.
BUG=none
TEST=Boot google/rex and print/check if able to overwrite values.
Change-Id: Ic2b9a158d219e6c6e7f6e7f0ae0f093c1183b402
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74141
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Jérémy Compostella <jeremy.compostella@intel.com>
Reviewed-by: Subrata Banik <subratabanik@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Intel's EHL FSP offers the possibility to select the connected hard
drive type to SATA ports. One has the option to choose between HDD ('0'
- default) and SSD ('1').
This patch provides a chip config so that this FSP parameter can be set
as needed in the devicetree on mainboard level.
Change-Id: Idb03aff5b6c5df592b47e2f4abe4fe58ac7151ba
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74946
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Assigning duty_offset while duty_width==0 has no purpose.
Under intel/common/block, previous assignment for fadt->gpe0_blk
resolves GPE0_STS(0) from xeon_sp/ebg/.../soc_pm.h and also assigns
value matching pmbase + 0x60.
Change-Id: Iaf688d9471ac527ac20307cf16216abdab731a06
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74827
Reviewed-by: Paul Menzel <paulepanter@mailbox.org>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
FSP-M is normally memmapped and then decompressed. The SPI DMA
controller can actually read faster than mmap. So by reading the
contents into a buffer and then decompressing we reduce boot time.
It is interesting that FSP-M takes an additional 8ms to execute. I
suspect since we call it 50ms earlier it's having to wait for one of
its dependencies.
BUG=b:179699789
TEST=Boot guybrush and see 30ms reduction in boot time
| 970 - loading FSP-M | 0.316 | 0.997 Δ( 0.68, 0.05%) |
| 17 - starting LZ4 decompress (ignore for x86) | 0.026 | 13.874 Δ( 13.85, 0.96%) |
| 18 - finished LZ4 decompress (ignore for x86) | 64.361 | 0.337 Δ(-64.02, -4.43%) |
| 2 - before RAM initialization | 0.534 | 0.529 Δ( -0.01, -0.00%) |
| 950 - calling FspMemoryInit | 1.455 | 1.132 Δ( -0.32, -0.02%) |
| 951 - returning from FspMemoryInit | 207.695 | 216.537 Δ( 8.84, 0.61%) |
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I850b1576501753a355e7b23745e04802a0560387
Reviewed-on: https://review.coreboot.org/c/coreboot/+/58988
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Beware that there's no XHCI2 controller and the USB4 controller device
pointers were added right after the xhci_0 and xhci_1 controller device
pointers.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I14725d4b546ffcca42e21bbe7756babaaff8fea3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74658
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Martin Roth <martin.roth@amd.corp-partner.google.com>
For early Sign of Life to work, we may need certain pin configurations
very early in boot (e.g. HDMI). This may happen before romstage GPIOs
are configured, and bootblock is not suitable for field upgrading
existing devices. Add a separate GPIO table that can be configured
when early graphics is invoked.
BUG=b:277861633
BRANCH=firmware-brya-14505.B
TEST=Builds and SoL functions on HDMI enabled variants
Change-Id: I7b3ce96a4166451e72aa70b3086eff3fb8b082b7
Signed-off-by: Tarun Tuli <taruntuli@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74697
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jérémy Compostella <jeremy.compostella@intel.com>
Return 0xf from PCI0 _STA method so that bit 2 is set which indicates
that the device should be shown in the user interface. This ports commit
c259d71928 ("soc/amd/stoney/acpi: Unhide PCI0 root device from OS")
forward from Stoneyridge to the newer AMD SoCs.
TEST=On Mandolin the PCI Express Root Complex now shows up in the device
manager on Windows 10 and when switching the view to 'devices by
connection', all PCI(e) devices are shown below it.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I4155556dc5df8f163fe06aa6719fadbb2684cc19
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74949
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch ensures that the PRERAM_CBMEM_CONSOLE_SIZE and
CONSOLE_CBMEM_BUFFER_SIZE hold a larger cbmem buffer size to contain
the entire FSP debug serial log.
The existing implementation was not appropriate, where the larger cbmem
size was even applicable for serial AP firmware (w/o FSP debug) image
as well.
This change is necessary to ensure that the FSP debug serial log is
always available, even in cases where the cbmem buffer size is
limited.
BUG=b:280481298
TEST=Able to build and boot google/rex with non-FSP serial AP image
and with FSP serial AP image. Able to see the AP log completely inside
the cbmem.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ib35780fd558c8b6d9aa2e17241131ea4a58c2b9c
Reviewed-on: https://review.coreboot.org/c/coreboot/+/75030
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This patch makes CSE sync in romstage default enabled unless ramstage
config (SOC_INTEL_CSE_LITE_SYNC_IN_RAMSTAGE) chooses to override it.
TEST=Able to build google/marasov with this change where CSE sync is
performed early inside romstage.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I3f5017fbcf917201eaf8233089050bd31c3d1917
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74805
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-by: Jérémy Compostella <jeremy.compostella@intel.com>
Adjust a few things so that the sleepstates.asl file is the same for
sb/amd and soc/amd. These adjustments don't have a functional impact.
Change-Id: I0cc9462b326cdc371ffdbf5759d8adc42456ce74
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74960
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Commit cbc5d3f34b ("soc/intel: Don't
report _S1 state when unsupported") added the `ACPI_S1_NOT_SUPPORTED`
option and commit 0eb5974def ("acpigen:
Add a runtime method to override exposed _Sx sleep states") added a
mechanism to override the enabled sleep states at runtime. However,
these were only hooked up to Intel sleepstates. so the options would
not have any effect on AMD platforms.
Apply the changes from these two commits to AMD sleepstates so that
both options can be used on AMD platforms as well.
Change-Id: I7d5ef2361e36659ac5c6f54b2c236d48713a07c9
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74959
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The commit a0b199c6b4 ("soc/intel/xeon_sp/spr: Add soc
set_cmos_mrc_cold_boot_flag") introduced a copy-paste issue in two error
messages. The error messages should mention the Intel platform SPR
instead of CPX. Fix that.
Change-Id: I4de61ec2cf9fbd98263a7a7a588938d548148656
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74956
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Johnny Lin <Johnny_Lin@wiwynn.com>
Reviewed-by: Lean Sheng Tan <sheng.tan@9elements.com>
Now that we don't need to find a specific resource in the set resources
function any more, there's no need to use hard-coded indices for the
fixed resources. Instead use an index variable that gets incremented
after each fixed resource got added. The index now starts at 0 instead
of at 1, but now the only requirement is that those indices are unique.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: Ida5f1f001c622da2e31474b62832782f5f303a32
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74849
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Himanshu Sahdev <himanshu.sahdev@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Fred Reitberger <reitbergerfred@gmail.com>
Drop the custom lpc_set_resources implementation that does some register
access that has no effect and then calls pci_dev_set_resources and use
pci_dev_set_resources for set_resources in amd_lpc_ops instead.
The SPI controller's base address got configured early in boot in the
lpc_set_spibase call and the enable bits got set early in boot in the
lpc_enable_spi_rom call.
TEST=The contents of the SPI_BASE_ADDRESS_REGISTER at the beginning and
at the end of the call stay the same, so it's simply a no-op.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I7a5e3e00b2e38eeb3e9dae6d6c83d11ef925ce22
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74848
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
The memory map granularity for those devices is 4kByte.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I8806128bdce8988f5cd7c8fa8a342fdb01eb7f42
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74844
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Since the 16MByte of memory-mapped SPI flash region right below the 4GB
boundary is both a fixed region and isn't decoded on a device below the
LPC device, but assumed to be decoded by the LPC device itself, it
shouldn't be reported as a subtractive resource, but as an MMIO resource
instead.
TEST=On mandolin the 16MByte MMIO-mapped SPI flash now show up as a
reserved region in the e820 memory map which wasn't the case before:
13. 00000000ff000000-00000000ffffffff: RESERVED
The Linux kernel doesn't show any new or possibly related errors.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Suggested-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Change-Id: Ib52df2b2d79a1e6213c3499984a5a1e0e25c058a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74839
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Martin L Roth <gaumless@gmail.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
At present the problem has only been reported with Alder Lake and
Raptor Lake FSP where MultiPhaseSiInit API is unable to return any ERROR
status. Hence, this patch ensures to select applicable W/A config to
read FSP return status from the FSP Reset HOB.
BUG=b:278665768
TEST=Able to select FSP_MULTIPHASE_SI_INIT_RETURN_BROKEN for ADL/RPL SoC
code and call into this API to know the return status from
MultiPhaseSiInit FSP API.
Without this patch:
IshInit() Start
IshDisable() Start
IshPerformGlobalReset()
....
....
FSP returning control to Bootloader with reset required return
status 40000003
FspMultiPhaseSiInit Index-1 returned 0 <-- after control returns
into coreboot, the `status` from the FSP API is reset to `0`
instead 0x40000003. Hence, coreboot avoid hitting the reset.
With this patch:
IshInit() Start
IshDisable() Start
IshPerformGlobalReset()
....
....
FSP returning control to Bootloader with reset required return
status 40000003
FSP: handling reset type 40000003 <-- coreboot is able to understand
the reset request in proper.
GLOBAL RESET!
global_reset() called!
HECI: Global Reset(Type:1) Command
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: I18a918cca7e19e03ed6020c55c86c64a94212963
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74785
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Tarun Tuli <taruntuli@google.com>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
This patch creates a function to read the FSP API Reset Status. This
function relies on the FSP Scheduled Reset HOB which holds the reset
type (warm/cold/shutdown) information along with any platform specific
reset need (like global reset).
Ideally FSP API should be able to return the status (both success and
error code) upon exiting the FSP API but unfortunately there are some
scenarios in ADL/RPL FSP where MultiPhaseSiInit API is unable to return
any ERROR status. Hence, this function provides an additional hook to
read the FSP reset status by reading the dedicated HOB without relying
on the FSP API exit status code.
Additionally, create FSP_MULTIPHASE_SI_INIT_RETURN_BROKEN config option
to handle broken FSP API return status issue.
Any SoC platform that selects the `FSP_MULTIPHASE_SI_INIT_RETURN_BROKEN`
config will call into this newly added API to get the FSP return status
from MultiPhaseSiInit.
BUG=b:278665768
TEST=Able to select FSP_MULTIPHASE_SI_INIT_RETURN_BROKEN for ADL/RPL SoC
code and call into this API to know the return status from
MultiPhaseSiInit FSP API.
Signed-off-by: Subrata Banik <subratabanik@google.com>
Change-Id: Ief5d79736cc11a0a31ca2889128285795f8b5aae
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74783
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Eric Lai <eric_lai@quanta.corp-partner.google.com>
Reviewed-by: Kapil Porwal <kapilporwal@google.com>
These were hidden because no Windows drivers existed, but now that
they do, the ACPI devices need to be visible in order for the
drivers to properly attach.
TEST=build google/banshee, boot Windows, verify Windows drivers
correctly attach to PCM/IOM devices.
Change-Id: Idbbaee29bffb49059d8450abd09e0c3f7b490fae
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74850
Reviewed-by: Subrata Banik <subratabanik@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: CoolStar <coolstarorganization@gmail.com>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
These were hidden because no Windows drivers existed, but now that
they do, the ACPI devices need to be visible in order for the
drivers to properly attach.
TEST=build google/drobit, boot Windows, verify Windows drivers
correctly attach to PCM/IOM devices.
Change-Id: I1520a71e318674baa234fc6a2126d1d17933d983
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74829
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: CoolStar <coolstarorganization@gmail.com>
Reviewed-by: Sean Rhodes <sean@starlabs.systems>
In order for Windows to detect/load drivers for any child devices,
the PCI0 root device status must be enabled and visible.
TEST=build google/liara, boot Windows, verify PCI child devices
visible in Device Manager.
Change-Id: I3fb1ba11247f0811120a4cf8a4fd99342ae201de
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74855
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
The change 'commit Iac37aaa5ede5e1cd ("Add Kconfigs to indicate
when CSE FW sync is performed")' adds support to choose CSE FW update
to be performed in ROMSTAGE or RAMSTAGE. The patch also introduced a
dependency on ME_RW firmware compression.
This patch removes the dependency between CSE FW sync in RAMSTAGE and
ME_RW firmware compression as these two are not related and should be
decoupled to support CSE FW sync in RAMSTAGE without the requirement
to compress ME_FW.
Signed-off-by: Anil Kumar <anil.kumar.k@intel.com>
Change-Id: I5ca4e4a993e4c4cc98b8829cbefff00b28e31549
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74796
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jérémy Compostella <jeremy.compostella@intel.com>
I forgot to remove these in commit 0fe36db154eb ("ACPI: Make FADT
entries for SMI architectural").
Change-Id: Ib1bc1dad6053ddb0454d4510917fd2bcf0901f35
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74811
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
For AMD, replace name RTC_ALT_CENTURY with RTC_CLK_ALTCENTURY
that points to same offset. Since the century field inside
RTC falls within the NVRAM space, and could interfere with
OPTION_TABLE, it is now guarded with config USE_PC_CMOS_ALTCENTURY.
There were no reference for the use of offset 0x48 for century.
Change-Id: I965a83dc8daaa02ad0935bdde5ca50110adb014a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/74601
Reviewed-by: Elyes Haouas <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
On boards with RECOVERY_MRC_CACHE FMAP section, populate type 0x63 BIOS
directory entry in RO with that section. If the RECOVERY_MRC_CACHE
section is not present, then fall back to RW_MRC_CACHE.
BUG=b:270569389
Signed-off-by: Fred Reitberger <reitbergerfred@gmail.com>
Change-Id: Ic5ac87685eaa5fec717e3efa4df7af511b4ce8aa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/73257
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@amd.corp-partner.google.com>
