Invert the default instead of selecting it everywhere. Restores the
ability to use its Kconfig prompt.
Beside Qemu targets, the only platforms that didn't select it seem
to be samsung/exynos5420, intel/cannonlake, and intel/icelake. The
latter two were about to be patched anyway.
Change-Id: I7c5b671b7dddb5c6535c97c2cbb5f5053909dc64
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/30891
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch revises the pad reset config of speaker reset GPIO pin from
RSMRST to PLTRST. Audio engineer suggested to reset the amps with
warm reset.
BUG=b:122441567
BRANCH=None
TEST=warm & cold reset & suspend_stress_test -c 10 and ensure the
speakers are working well.
Change-Id: I87c554b186b068da93e1662a97afaf01dddae0ef
Signed-off-by: Gaggery Tsai <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/c/30866
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
PLT_RST_L was asserted twice at boot-up and a glitch was observed
when coming out of suspend mode. Configure PLT_RST_L pad IOSSTATE
from HIZCRx1 to be masked.
BRANCH=octopus
BUG=b:117302959
TEST=Verified no glitch on PLT_RST_L at S3 and PLT_RST_L stays high
3.3v during S0ix.
Change-Id: I8c23aadda72be54fb45e67aab2bc8ed51e473bae
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/30815
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Some usb devices exhibits signal loss which causes xHCI entering
compliance mode. The resolution is to disable xHCI compliance mode.
BRANCH=octopus
BUG=b:115699781
TEST=Verified usb operation successfully.
Change-Id: I41fecaa43f4b1588a0e4bbfc465d595feb54dd24
Signed-off-by: John Zhao <john.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/30817
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
butterfly is a Sandybridge device, and selecting Ivybridge
breaks libgfxinit currently due to CPU mismatch
Test: build/boot butterfly w/libgfxinit
Change-Id: I1a7f5a3681d21a256834b11b545855c4365f5f78
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30820
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
After f5ca922 (Untangle CBFS microcode updates) got merged, all
mainboard using intel apollolake, cannonlake, coffeelake, glk,
kabylake, skylake, icelake and whiskeylake get affected.
Using INTEL_LPSS_UART_FOR_CONSOLE instead of UART_DEBUG
and set default console for each platform.
BUG=N/A
TEST=Build and test on Sarien platform, by default we can still get
console from cbmem, and enable CONSOLE_SERIAL can get logs from UART
port 2.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I550a00144cff21420537bb161c64e7a132c5d2de
Reviewed-on: https://review.coreboot.org/c/30853
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Enable the EC_AP_INT_ODL interrupt on GPIO_134 for all octopus boards
that support it. Also removing unnecessary IO standby support since we
don't use this pin to wake up the SoC.
BRANCH=octopus
BUG=b:122552125,b:120679547
TEST=CTS tests with changes
Change-Id: I018864ae5fa400372b5b443e49828e8202b9aa4d
Signed-off-by: Jett Rink <jettrink@chromium.org>
Reviewed-on: https://review.coreboot.org/c/30788
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Most boards currently do not use EC firmware from SPI flash in the
IFD, this hides this option by default and shows it only for boards
that need it.
A new config variable MAINBOARD_USES_IFD_EC_REGION is introduced to
enable this option for boards that need it.
The following list of boards requiring this was provided by
Lijian Zhao:
1. intel/cannonlake_rvp
2. intel/coffeelake_rvp
3. intel/icelake_rvp
4. google/sarien
5. google/hatch
Change-Id: I52ab977319d99a23a5e982cc01479fe801e172a7
Signed-off-by: Jan Tatje <jan@jnt.io>
Reviewed-on: https://review.coreboot.org/c/30697
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Kukui is going to use ADC#4 as SKU ID, and utilizing EC BoardID as
global board_id (i.e., board revision).
BUG=b:122060615
TEST=make; manually tested on Kukui P1 board.
Change-Id: I7bba368c141a7ba6db11f24b8e8e7158f0fc729e
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/30617
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: You-Cheng Syu <youcheng@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
The ID from ADC on Kukui supports 16 different values and we should list
all voltage values ahead.
BUG=b:80501386
TEST=make; manually verified on Kukui P1
Change-Id: Ic3abe07abfe818ca68e180c262fd431d1167b801
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/30619
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: You-Cheng Syu <youcheng@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
From `boardid.h`, the uninitialized ID values should be BOARD_ID_INIT
instead of BOARD_ID_UNKNOWN.
BUG=b:80501386
TEST=make; manually verified on Kukui P1
Change-Id: Ie5267e575e38b92ec64a7317defbd00ee153fa0a
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: https://review.coreboot.org/c/30618
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: You-Cheng Syu <youcheng@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
1) Add a Platform Data Region called SI_PDR which is allocated in the flash
descriptor for this platform
2) Add a DIAG_NVRAM region for use by the diagnostic payload for non-volatile
storage.
3) Encapsulate both RW_LEGACY and DIAG_NVRAM in a region called RW_DIAG
so it is clear they are associated.
4) Move the RW_DIAG region to the start of the RW region so that once we can
re-enable a larger BIOS region this sub-region will be in the uncached area
since it is not accessed on a normal boot.
BUG=b:119435206
TEST=tested on Arcada board to ensure expected regions are present
Change-Id: Ieb8bc4cf70d0a931e4944210112cfaf5c543f9f3
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30755
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Sdram config sdram-lpddr3-hynix-4GB.inc for H9CCNNNBKTMLBR-NTD can't
boot on Mickey. It's confirmed that the right config for Hynix
H9CCNNNBKTMLBR-NTD is sdram-lpddr3-hynix-2GB-BK.inc.
BUG=b:122239609
BRANCH=master
TEST=boot on mickey
Change-Id: Ifeaadda50d939e0c118cb7fe3964dcd08b709c2a
Signed-off-by: Loop_Wu <Loop_Wu@asus.com>
Reviewed-on: https://review.coreboot.org/c/30761
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Julius Werner <jwerner@chromium.org>
This patch disables the SA IPU for hatch since it is
not using the IPU.
Change-Id: Ib2afc4cc4fd7ef98365b0b98130b0e8bc757ac2a
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/30699
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reading nvdata from non-volatile flash storage. With this patch, it will
pass the firmware test that corrupts FW_MAIN_A and boots up with
FW_MAIN_B.
BUG=b:80501386
BRANCH=none
Test=test_that --board=kukui 172.23.213.147 firmware_CorruptFwSigA
Change-Id: I9ef6bff019ee986ff018202bfd4d4a875526ec6c
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/30701
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: You-Cheng Syu <youcheng@google.com>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Explicitly configure the minimum assertion width values to ensure
that they are set as expected and are not using unknown defaults.
Change-Id: I9a88e5b6002137df6e572b84d0de8a69522938f9
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30722
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Enable the active-low recovery mode GPIO now that new boards are
available which have an external pull-up instead of a pull-down so
it can be asserted properly by servo.
This was tested on a Sarien system by holding the recovery button
on the servo board and tapping the cold reset button and ensuring
that it enters recovery mode.
Change-Id: I3216580bc94de71b05bf9382f15d0c4d428cb9fa
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30721
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
These platforms use the standard fixed function power button
and do not need a second power button device declared or the
kernel will end up with two devices reporting the same event.
Change-Id: I6fe2b201a6a6f6307a0c4bd6a61f56cfcdd88bf4
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30720
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Following changes are done to enable touch screen support on hatch
1. Enable I2C1 device at 400Khz at 3.3V
2. Configure GPIO for touch screen
3. Add ACPI entry for ELAN touch panel
4. update GPIO table with not connected GPIO pins for panel
BUG=b:120914069
BRANCH=none
TEST=check if code compiles with changes.
Change-Id: I8dab07dad4cb197865bb9cf0e8da240810fcfabe
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/30425
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Main objective for this change is to export the bluetooth reset
gpio to the kernel for use in an rf-kill operation.
To do so, we enable USB acpi and define all of the USB2 devices,
which includes bluetooth's reset gpio information.
BUG=b:119899987
TEST=build and flash to rammus, log into rammus and
'cat /sys/firmware/acpi/tables/SSDT > /tmp/ssdt.dml', copy
that ssdt.dsml to /tmp/ssdt.dml on host machine,
'iasl -d /tmp/ssdt.dml', then verify that "reset gpio"
shows up in the HS03 node's _DSD package in the table.
Signed-off-by: marxwang <marx.wang@intel.com>
Change-Id: Ieadb3609c7634a20e96c7c4dfb96f5e3f23e468b
Reviewed-on: https://review.coreboot.org/c/30607
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Elan touchpad require connected i2c clock to be running at 400Khz, with
the modification can get 404Khz speed from Arcada EVT platform.
BUG=b:119628524
TEST=Build and boot up on Arcada platform, measure the i2c clock is
around 400Khz.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: If717cdd6b73394125df54d90f729ffb4ef37b087
Reviewed-on: https://review.coreboot.org/c/30653
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
The vbt was extracted from the option rom found on stock images.
The vbt.bin is the same across all variants.
The VBT has a modified BDB block 43, the 'Backlight info block' such
that the inverter type for the panel in use is set to
2 (BDB_BACKLIGHT_TYPE_PWM) instead of 0 (BDB_BACKLIGHT_TYPE_NONE).
This only seems to matter on Windows, as without it changing the
backlight duty cycle does not work.
Change-Id: I82c72c561e1058e0b77d80baf330b64f7c6b08e3
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30487
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Without eist enabled, fizz's CPU clocks are locked at the
base frequency, and don't scale up or down. This prevents
fizz from idling properly and turbo boost from functioning,
so enable it (as is done for all other KBL boards)
Test: build/boot google/fizz, ensure CPU clocks scale as expected
Change-Id: I77dd0e1df1bf88f5bae18e9f832ca8d60fb777b4
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30674
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
We have init_bootmode_straps() defined for the same purpose.
Change-Id: Ia2692d8f8986247ea4ce889d6252d3c4c8b27bc4
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30398
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add DRAM support for google kukui.
BUG=b:80501386
BRANCH=none
TEST=Boots correctly on Kukui
Change-Id: I1ed01404343745c883b22a648966327bdcabc5c2
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/28438
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Add reset delay in power resource to prevent from failing to bind after
unbinding. And boards including yorp series - bobba / phaser and bip series
- ampton are affected.
BUG=b:121286833
BUG=b:117474421
BUG=b:121019320
BRANCH=None
TEST=emerge-octopus coreboot,
verified that WACOM touchscreen can re-bind successfully.
Change-Id: Icf690fc8e9450d559b642d1c88e29ff5d52c5488
Signed-off-by: Marco Chen <marcochen@chromium.org>
Reviewed-on: https://review.coreboot.org/c/30422
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Correcting order of display related GPIOs and also adding not connected
pin definitions for display GPIOs
BUG=b:120914069
BRANCH=none
TEST=check if code compiles with changes.
Change-Id: I9498284d263516f65513d6395883b6b09dd70fd5
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/30544
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
This patch enables the SATA for hatch,
* Enable the SATA port 1.
* Configure the GPIO for SATA.
BUG=b:120914069
BRANCH=none
TEST=USE="-intel_mrc -bmpblk" emerge-hatch coreboot.
Change-Id: Iaf800d1531688c3d3b82600038ea1d7160ae4b0b
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/30435
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Internal pull up need to be enabled for GPD3 as power button pin for
PCH according cannonlake pch EDS vol1 table 17-1. Without that pin will
stay floating and hook up XDP can cause system shutdown as power buttone
event will trigger.
BUG=N/A
TEST=Hook up XDP on sarien platform, able to boot up into OS and stay
at power up state.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: Ibe21da5f4a0797a3d62b36899f023908b46c25bf
Reviewed-on: https://review.coreboot.org/c/30374
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Modify the vbios's eDP signal setting from level0(0dB)
to level1 (3.5dB) for bard
Add VBT blobs and include it in cbfs
BUG=b:119448457
TEST=Test & measure eDP signal
Change-Id: I0b854a6adad43844282aed61d26e798727b5cb62
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30375
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
According to issue tracker b:119238959 #4 & #6.
Hardware modify design to make GPP_E3 to be a switch of touchscreen
I2C CLK and SDA.
Control GPP_E3 to make touchscreen I2C CLK and SDA keep low during
power on initialization to avoid data transfer during this time.
After touchscreen IC initial complete, control GPP_E3 to high to
make touchscreen I2C CLK and SDA work normally.
Depending on touchscreen IC specification, device take 105ms for
power on initialization.
Change delay time from 120ms to 105ms.
BUG=b:119238959
BRANCH=firmware-rammus-11275.B
TEST=emerge-rammus coreboot chromeos-ec chromeos-bootimage
Flash FW to DUT, run S5 stress test and verify the result
Signed-off-by: YanRu Chen <kane_chen@pegatron.corp-partner.google.com>
Change-Id: I86452c1445243c499aeaf931dba286db169c5628
Reviewed-on: https://review.coreboot.org/c/30180
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch incorporates following changes to enable console on UART0
1. update default console number to 0
2. Enable PCI port for UART0
GPIO configuration will be done by coreboot based on correct console
number.
Change-Id: I735d33674b276b28e2cbb753d3a6d83edbabe89d
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/30424
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
This patch modifies the hatch flash layout to support
IFWI 1.6 with the following regions,
Flash Region 0: Descriptor
[0x0 - 0xFFF]
Flash Region 1: IFWI (consist of ME and PMC FW)
[0x1000 - 0x3FFFFF]
Flash Region 2: BIOS
[0x1400000 - 0x1FFFFFF]
Change-Id: I3d05fb50e970737a2552b85d6aebed943bf2b6cb
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/30413
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This reverts commit a914152fa6.
Reason for revert:
According to the partner on this project, custom values like this
are no longer necessary.
Change-Id: I393eb4997f58abe0f77161999474994f06741519
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/c/30347
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
WWAN chip support 3 interfaces as pci express, USB 2.0 and USB 3.0, the
usgae of Sarien choose to only use USB interface but not over pci
express, so totally disable pci express root port 12.
BUG=b:1246720
TEST=Boot up into OS with WWAN attached, cold boot and warm boot 10
cyles can still device can be listed under lsusb.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: Ic4da393c0c0d903848111e1c037c2730c86afa7d
Reviewed-on: https://review.coreboot.org/c/30350
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
This reverts commit 999b916015.
The DMIC doesn't have an ACPI id. The patch which enables ACPI
device with id DMIC may create conflict in the feature. Also the
ACPI id "DMIC" doesn't comply with ACPI naming conventions. The
issue for which the patch was introduced, is already addressed in
kernel DMIC driver and the patches are upstreamed in to the Linux
kernel.
Change-Id: I42cb076700dcb5906599471bebfcd5b265b17644
Signed-off-by: Jenny TC <jenny.tc@intel.com>
Reviewed-on: https://review.coreboot.org/c/30151
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Turn on power optimizer of PCH side DMI and SATA controller.
BUG=N/A
TEST=Build and boot up into sarien platoform, able to finish 100 cycles
of s0ix.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I41da2b4106d683945cdc296e2a77311176144f43
Reviewed-on: https://review.coreboot.org/c/30212
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Set CONFIG_NO_FADT_8042 to avoid probing for the 8042 controller.
This speeds up boot on nocturne by 1.3 seconds:
Before change:
[2.162266] EXT4-fs (mmcblk0p3): mounting ext2 file system using
the ext4 subsystem
After change:
[0.867735] EXT4-fs (mmcblk0p3): mounting ext2 file system using
the ext4 subsystem
BUG=b:120960844
BRANCH=none
TEST=build, flash, and boot nocturne; check dmesg to verify that
boot is faster and that you don't see the following log in dmesg:
[0.671501] i8042: Probing ports directly.
Change-Id: I62a16e6de5e74fa17970d9967f6d1628497ec1d3
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/30283
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The TXE PCI device serves no function under Linux, and doesn't
work properly under Windows, so disable/hide it from the OS.
Test: Boot Windows 10 on google/squawks, verify TXE not visible
under Device Manager.
Change-Id: Idaa152e15106b826fd5aa787090acd45719f4228
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30235
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Commit 73b723d [google/cyan: Switch Touchpad and Touchscreen...]
in additon to changing the touchpad/touchscreen interrupts from
edge to level triggered, also marked them as maskable. This not only
broke the touchpad functionality, but caused issues with the touchpad
as well. Revert the touchpad to being non_maskable for all cyan
variants with a touchscreen.
Test: boot GalliumOS on google/cyan with a range of kernel versions
(4.15.18, 4.16.13, 4.17.x, 4.18.x) and verify touchscreen functional,
touchpad working properly (not jittery)
Change-Id: I0e0357912f9404af7d0f4e7938a1a94c74810b37
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30236
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The previous settings caused the I2C frequency for the audio bus to be
too high, at 417kHz. The settings in this commit correct the frequency
to 396kHz.
BUG=b:119423345
Change-Id: Ibed886e6e1b0df4df6b87f6291e515364b3bf718
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/c/30129
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This reverts commit ad41f55123.
Reason for revert: <Issue have seen on EVT platform that vboot always fail to verify keyblock A>
BUG=b:121169122
Change-Id: I2790ef3463a228008b614498009fbdc8b493cfb0
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/30286
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Commit d80884ea5a ("mb/google/kahlee: Disable IOMMU") disabled the IOMMU
in all kahlee variants, but omitted the explaining comment only in
liara's devicetree.cb. Copy this comment to liara.
Change-Id: I564013a16217445003467e2a0579abd50597b205
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/c/30166
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Using ${...} in some places is slightly confusing.
Fixes: 395cbb4f97 ("mb/*/*/Kconfig: Use CONFIG_VARIANT_DIR for devicetree")
Change-Id: Id0856a10d92786a41d45ca697945699f6f4c1f4c
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/c/30163
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Bobba would prefer to use different SAR values per sku-id for regulatory
compliance. This commit uses the newly added interface for custom wifi
SAR CBFS filenames.
CQ-DEPEND=CL:*729429
BUG=b:120958726
BRANCH=octopus
TEST=build
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Change-Id: I354382d651d65d533459f0ca460ca6fd6de547fd
Reviewed-on: https://review.coreboot.org/c/30223
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
According to bard/ekko cpu types, PL2 need to set the values
1. KBL_U PL2 is 25w.
2. KBL_R PL2 is 29w.
BUG=b:120874861
TEST=power on and check the DUT can boot up well
Change-Id: I5f9d672c4244c363a7cfb362653663a065259fc0
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30178
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This patch implements board reset on the Cheza board. The real board
reset used by the operating system uses the PMIC, but unfortunately the
PMIC needs to be configured right for that to work. The PMIC
configuration currently happens in the Qualcomm blob (QcLib) that is run
from romstage, but vboot needs to be able to reboot during verstage
already. Porting all the PMIC initialization code to run in the
bootblock seems excessive (and at odds with the goal of doing as little
as possible before verification), so we'll just do a little hack and ask
the EC to perform a cold reset instead. For vboot purposes, this should
work just as well.
BUG=b:118501305
TEST=Hacked vboot code to call vboot_reboot(), confirmed that board
reset and came back up as expected.
Change-Id: I3858d95f481884a87c243d4fa3d6369c1e8a5a2c
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/29849
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Correct Ram_ID=0b0000 SPD Module Part Number mismatch last alphabet 'C'
to "H5AN8G6NAFR-UHC".
BUG=b:120000816
BRANCH=master
TEST=mosys memory spd print all
Change-Id: I4f4b83589ad6b53c0a24f2637f0fe8b92a1168e3
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30208
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Correct to add Ram_ID=0b0001 SPD Module Part Number mismatch last alphabet 'C'
to "H5ANAG6NAMR-UHC".
BUG=b:120000816
BRANCH=master
TEST=mosys memory spd print all
Change-Id: I4d320b2e10c4865456a9a9ccb400db5dd9256b3e
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30177
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Creating skeleton files and directories in mainboard for the new Hatch
board. This is to facilitate development for different parties
involved.
BUG=None
BRANCH=None
TEST=./util/abuild/abuild -p none -t google/hatch -x -a
Change-Id: I5fc60c178f83034abe5d846d0f4169072b66f448
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/30169
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Change-Id: I64e79904c7ad95091ea29d9f80444c4e3b493471
Signed-off-by: T Michael Turney <mturney@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/29298
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Update the TRACKPAD_INT1_1V8_ODL GPIO configuration so that it acts as a
wakeup source
BUG=b:119598593
BRANCH=octopus
TEST=Ensure that the system wakes up on trackpad events. Ensure that the
suspend_stress_test runs successfully for 25 iterations.
Change-Id: I28292682cf9c8037abb87d265e49a60139550db2
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/30171
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Change-Id: I15cfbbab15b940641c3952f2cfb4b11c37574816
Signed-off-by: T Michael Turney <mturney@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/29299
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Disable SATA port 0 and port 1 as that's not used as SATA on platform.
BUG=N/A
TEST=Build and boot up fine on google arcada board.
Change-Id: I1b8801f7a0f9b7847b85d7c315fa0a2093b32f70
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/30091
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
PEN_EJECT GPIOs are active high and also require an internal pull-up.
Update the GPIO configuration appropriately.
BRANCH=octopus
BUG=b:117953118
TEST=Ensure that the system boots to ChromeOS. Ensure that the stylus
tools open on pen eject. Ensure that the system can enter S0ix and S3
states successfully when the pen is inserted. Ensure that the system
wakes on Pen Eject. Ensure that the system does not enter S0ix and S3
states when the pen is placed in its holder. Ensure that the
suspend_stress_test runs successfully for 25 iterations with the pen
placed in its holder.
Change-Id: Ibf9cb214a8ce7561efbb77a7e99d1e386cf064c3
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/30107
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Update the GPIOs for the next board build. Mostly minor changes but
the polarity change on GPP_E8/RECOVERY on sarien will result in it
booting to recovery every time unless using new hardware.
For this reason the recovery mode GPIO that is passed to vboot is
commented out for sarien. It is only used for testing and currently
it is useful to have an image that works on both board versions.
Change-Id: I32d84f3010cb4d3968370a03f7e191b1710a50e8
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30062
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently CoffeeLake FSP is incorrectly modifying GPIO pad configuration
if specific UPD variables are not set as it expects.
This affects the display-related SOC pads with the following UPD variables:
UINT8 DdiPortBHpd; // GPP_E13
UINT8 DdiPortCHpd; // GPP_E14
UINT8 DdiPortDHpd; // GPP_E15
UINT8 DdiPortFHpd; // GPP_E16
UINT8 DdiPortBDdc; // GPP_E18/GPP_E19
UINT8 DdiPortCDdc; // GPP_E20/GPP_E21
UINT8 DdiPortDDdc; // GPP_E22/GPP_E23
UINT8 DdiPortFDdc; // GPP_H16/GPP_H17
Until FSP is fixed to not touch the pad configuration this workaround
will reprogram the GPIO settings after FSP-S step so they are correct
when the OS attempts to use them.
This was found in CoffeLake FSP Gold release:
https://github.com/IntelFsp/FSP/tree/master/CoffeeLakeFspBinPkg
As well as the current top-of-tree for the FSP sources.
BUG=b:120686247,chromium:913216
TEST=verify correct GPIO configuration for GPP_E group in the kernel
Change-Id: I19550c4347cf65d409de6a8638619270372c4d0a
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30113
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Synaptics Trackpad wake event is incorrectly routed to GPE0_DW2_02. The
concerned GPIO is not connected and hence wont trigger a wakeup. Fix the
GPE wake configuration for synaptics trackpad.
BUG=b:120666158
BRANCH=octopus
TEST=Ensure that the wake on trackpad works with Synaptics touch pad.
Ensure that the system can enter S0ix successfully(run
suspend_stress_test -c 25).
Change-Id: I87b8c266266280f61700839d428e6f8938b0f72f
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/30105
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
FSP defined a special clock source usage 0x70 for PCH LAN device, update
that to google sarien platform.
BUG=b:120003760
TEST=Boot up into OS, ethernet able to be listed in ifconfig.
Change-Id: I9f945be4f0ce15470ab53f44e60143f3fd0fddf8
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/30100
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Part Number
Correct Ram_ID=0b0011 SPD Module Part Number to "MT40A1G16KNR-075:E" from
"4ATS1G64HZ-2G6E1".
BUG=b:120000816
BRANCH=master
TEST=mosys memory spd print all
Change-Id: I9d582b3753de9a48865eb6eca7e4fbdb31b799ff
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30049
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Number
Correct Ram_ID=0b0000 SPD Module Part Number to "H5AN8G6NAFR-UH" from
"HMA851S6AFR6N-UH".
BUG=b:120000816
BRANCH=master
TEST=mosys memory spd print all
Change-Id: I1f6e885638589a35334a9a8f905af4877c5d1f91
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30048
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Part Number
Correct Ram_ID=0b0010 SPD Module Part Number to "MT40A512M16JY-083E:B"
from "4ATF51264HZ-2G3B2".
BUG=b:120000816
BRANCH=master
TEST=mosys memory spd print all
Change-Id: I6847a55968260cdbc1588ddeb8d23c515ad87920
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30050
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
The Intel Sensor Hub was enabled on the wrong variant so this change
moves the enable from sarien to arcada.
Change-Id: If933623f7dbb45c4805fb61430465236eca19ee8
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30070
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Li1 Feng <li1.feng@intel.com>
Reviewed-by: Jett Rink <jettrink@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
A new liara specific VBIOS updating eDP power sequence is available now,
Change Kconfig to use it if board is google liara.
BUG=b:120534087
TEST=Build liara, booted, tested eDP test compliance.
Change-Id: I444cfa0bd755480e006f11c0d692b25b96129c29
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/c/30090
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Provide rise/fall times as measured on existing boards. This will
need adjusted for new boards but provides a starting point that
makes I2C clocks look reasonable.
Tested by measuring I2C bus speed and rise/fall times with a scope.
Change-Id: Ic18010f5efc41dcee8925d696767ba2c44e3df4b
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30069
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Platform have a 32MB SPI chip, so we can increase the bios region from
16MB to 28MB.
BUG=b:119267832
TEST=Build and boot fine on sarien platform.
Change-Id: I9bc0fa0f662e5ec64e77f2005dbb2e7edb8b2524
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/29945
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Init SPI bus 0 to connect TPM, configure interrupt type of GPIO CR50_IRQ,
implement tis_plat_irq_status(), and set up chromeos GPIO table for TPM
interrupt.
BUG=b:80501386
BRANCH=none
Test=Boots correctly on Kukui.
Change-Id: Ieaa6ae65fbfb5ab6323e226e8171dd7a992c3a39
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/29192
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Set GPIO D22 low to get WWAN_PERST#_R asserted.
BUG=N/A
TEST=Boot up with Arcada board, check WWAN get detected as USB devices
through lsusb command.
Change-Id: Ie848cd19fdf3b6c4b6abeb5fa3f566e5e4e7e928
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/30030
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add the USB device information for the sarien/arcada variants.
This includes the ACPI _PLD group definitions for the external
ports that indicate which USB2 and USB3 ports share the same
physical interface.
Change-Id: I0b936127954ba09c61ccb871bfc62ee7d99da263
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30000
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add ACPI _PLD group definitions for the external ports
that indicate which USB2 and USB3 ports share the same
physical interface.
Change-Id: I7f85720a878a3774d453a9adb82518722f7ba23d
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29999
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Enable DPTF support for sarien/arcada boards. This is currently
using placeholder values that are identical that will be updated
after thermal tuning is done.
Change-Id: I7d51c3b38068fc25927c8dafc0bd9069b29d77f5
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29762
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Set WWAN_GPIO_PERST#(GPP_D22) to low at bootblock stage to meet
the logic output for WWAN_PERST#_R to high.
BUG=120004153
TEST=Boot up Sarien board, check WWAN get detected as USB
devices through lsusb.
Change-Id: I16f1101c64dfd4dcb5e8342fdb925951f6f2f90b
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30017
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
update the new sku ids of bard/ekko
BUG=b:120257865
BRANCH=Nami
TEST=emerge-nami coreboot chromeos-bootimage
write the new sku id in cbi and verify the fw to
check it can get the correct settings by the sku id
Change-Id: I3579d3d8042a270d8ea8e2f7b5612ff8e2cdfa7b
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30031
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change enables mode change as a wake source from S3 and
S0ix. Thus, any time the device switches between clamshell and tablet
mode while it is suspended, it will be treated as a valid user event
and hence wake source.
BUG=b:120349473
BRANCH=octopus
TEST=Verified that octopus wakes up on mode transitions.
Change-Id: Ib224df434730f873ce5514303e5d043cbc85a9a4
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/30001
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
The ASRock H81M-HDS doesn't implement a finalise handler. To fix
this, and reduce code duplication in the process, make a common
implementation. There should be no functional change to boards with
existing finalise handlers, since the code is identical among them and
the new, common implementation.
Tested on an ASRock H81M-HDS. The finalise handler works.
Change-Id: I13b581a2219288019a4e0c9e618db3ac7c3c15ab
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/c/29975
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
The WACOM 5C01 touch panel power-up delay of 10mS is too aggressive
and causes "failed to change power setting" errors in the kernel, so
this change increases the power-up delay to 20mS which allows enough
time for the WACOM device's i2c controller to wake up.
BUG=b:120090384
BRANCH=none
TEST=flash and boot nocturne, log into kernel, execute the following
command and make sure the string is not found :
dmesg | grep "failed to change power setting"
Change-Id: I1db0b3f5ce666b79d8ada2939ec865233ce52a56
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/29988
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
We discovered that the gpios previously used for FPMCU_INT_L were in
two different groups with two different voltages (C group was at 3.3V
and D group was at 1.8V). Moving both to B group which is at 3.3V.
BUG=b:119447525
BRANCH=Nami
TEST=unlock OS with fingerprint
register fingerprint
run powerd_dbus_suspend and see if it goes int s0ix
Change-Id: I2332b0eb7a2f74e8178b95a23c8ac2091027a071
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/29872
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Update USB port info according to the schematic file.
BUG=none
BRANCH=master
TEST=Compiles successfully and boot on DUT.
Change-Id: I7383b3d676fd7c775a6d749c70af65b28cf941eb
Signed-off-by: David Wu <David_Wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/29912
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Use of device_t is deprecated.
Change-Id: Ief858f6612d1c7b4b0c286cf5938f8c29055f1b5
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/29915
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Use acpigen_write_processor_cnot to implement notifications to the CPU.
Automatically generate \PPKG in SSDT.
Change-Id: I79d2eed9b89b420554ce10d1fc0f151b1872afe2
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/29890
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Use acpigen_write_processor_cnot to implement notifications to the CPU.
Automatically generate \PPKG in SSDT.
Change-Id: Iecc54e94484f5f11e0ba8ef6d1d844276e484b4d
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/29886
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The reason for this code cleanup is the legacy
Google Purin board which isn't available anymore
and AFAIK never made it into the stores.
* Remove broadcom cygnus SoC support
* Remove /util/broadcom tool
* Remove Google Purin mainboard
* Remove MAINTAINERS entries
Change-Id: I148dd7eb0192d396cb69bc26c4062f88a764771a
Signed-off-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/29905
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
According to aleena thermal testing to set STAPM values.
skin scalar for 80%.
time constant for 2500s.
power limit for 7.8w.
BUG=b:72979852
TEST=test build for thermal check.
Change-Id: I09f1c1052dd317969546ac7d2bbde14cc563c160
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/29795
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Correct Ram_ID=0b0001 SPD Module Part Number to "H5ANAG6NAMR-UH" from "HMAA51S6AMR6N-UH".
BUG=b:120000816
BRANCH=master
TEST=mosys memory spd print all
Change-Id: I59d920498ff6b73e9e7b2887771ad6bc6c6c0b66
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/29873
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Implement HD Audio verb table for RealTek ALC 3204/3254 codec on google
sarien and arcada board.
BUG=b:119058355,119054586
TEST=Confirm audio play back is working on Sarien and Arcada board.
Change-Id: Icedbb510c7668d96c99c657091fc865f03bf7783
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/29484
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
This removes CEIL_DIV and div_round_up() altogether and
replace it by DIV_ROUND_UP defined in commonlib/helpers.h.
Change-Id: I9aabc3fbe7834834c92d6ba59ff0005986622a34
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/29847
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
PMIC provides power features like auxadc, buck/ldo,
interrupt-controller..etc
BUG=b:80501386
BRANCH=none
TEST=Boots correctly on Kukui
Change-Id: Ic247faf73517f6512f9c9a69ba0254c749d68d4c
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/29422
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The aleena board uses a display that's not compatible with current VBIOS.
A VBIOS specific for aleena has been merged into blobs, so modify Kconfig
so that it loads the new VBIOS when building aleena, but load original VBIOS
for all other boards under kahlee folder.
BUG=b:112618193
TEST=Build each board under kahlee, one at a time. After each build, opened
build/config.h and searched VGA_BIOS_FILE to verify that the string only
changed for aleena, all other boards remained with original string.
Change-Id: Iccd0853692680908d951edd142a2d8e13a561391
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/c/29870
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
This change gets rid of bid0_override_table as part of clean up effort
to deprecate bid0. Additionally, it updates the touchscreen enable
GPIO in overridetree and gets rid of code in variant.c to update enable
gpio at runtime.
BUG=b:119885949
Change-Id: I527973747e7d81ec47997da57eeb15f38d3ac2fd
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/29787
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
This change is to bump fsp_memory_mainboard_version in order to
trigger MRC full training
BUG=b:119481870
CQ-DEPEND=CL:*716558
BRANCH=reef, coral
TEST=make sure MRC retraining is triggered and the MRC cache is
updated to newer version.
Change-Id: I92463045f7a808fb25aaa7a2d5f6fcde36dfb458
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/c/29647
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
BUG=b:112282079
BRANCH=None
TEST=1. run evtest and make sure trackpad shows up in list
2. Able to wake system from S3 using trackpad
Change-Id: I86d6b7815147d558065611604363bb607119c154
Signed-off-by: Shelley Chen <shchen@google.com>
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/29752
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
BUG=b:112332115
BRANCH=None
TEST=ensure at bootup that /sys/devices/pnp0/00:05 exists
and driver link to '../../../bus/pnp/drivers/i8042 kbd'
Also, can now see keyboard in evtest.
Change-Id: I2a6b382be84bc5201beafe21ff8ddee3738bc5c2
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/29750
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch includes support for both ICL ES0 and ES1 samples.
Detailed document is here: Documentation/soc/intel/icelake/iceLake_coreboot_development.md
TEST=Able to build and boot dragonegg.
Change-Id: I2cc269cb0050bf5b031f48cfe114485c55ab8fa9
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/29749
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
The SD cardreader is on USB bus, not on SDIO/SDXC.
BUG=b:119798840
BRANCH=master
TEST=Compiles successfully and boot on DUT.
Change-Id: I8015fe35a4ff79469b5781942f588c3e1b88b751
Signed-off-by: David Wu <David_Wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/29765
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Set GPIO GPP_B4 to high to enable touchscreen wakeup.
BUG=b:119594783
BRANCH=master
TEST=DUT can wake up with touchscreen.
Change-Id: If0c9493dec367c7813047c7994cc83537aaef141
Signed-off-by: David Wu <David_Wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/29769
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The touchpad and touch-panel CLK frequency should be smaller
than 400 kHz which described in spec.
Overwrite i2c speed parameters by overridetree.cb
BUG=b:119540449
BRANCH=master
TEST=emerge-octopus coreboot chromeos-bootimage
flash bios and check the touchpad i2c frequency meets the spec.
Change-Id: I32c3e1bbfc2cdf39e9b7865a69996e54346d5f93
Signed-off-by: Carl Yang <carl_yang@asus.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/29694
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This change deprecates boards with id < 2. It updates touchscreen enable
GPIO in overridetree and gets rid of variant.c to update enable GPIO at
runtime. Additionally, it configures old enable GPIO as NC.
BUG=b:119885949
Change-Id: I42fb7ef90e421118a8fdfa0d343d0bcf4a9bc087
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/29786
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
This change gets rid of bid0_override_table as part of clean up effort
to deprecate bid0. Additionally, it updates the touchscreen enable
GPIO in overridetree and gets rid of variant.c to update enable gpio at
runtime.
BUG=b:119885949
Change-Id: If14abb324d9422720ca4d0f0859e092319d454ee
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/29785
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
This change updates the configuration of GPIO_178 to be active low as
per latest revision on different octopus variants. This effectively:
1. Gets rid of early_gpio_table in different variants -- phaser, meep,
fleex, bobba.
2. Deprecates board id < 2 for bobba, board id < 1 for fleex and
phaser.
3. Adds special early_gpio_table in yorp which has GPIO_178 as an
active high signal.
BUG=b:119885949
Change-Id: I024199a8f1f96db57f8fa60c4d265789cd3a0493
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/29784
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Change the board id detection to support rev5, since the 2T mode still
needed in DVT build.
BUG=b:116082728
TEST=verify by ODM.
Change-Id: Ibb4cc1fd2bb54984cb7a8856ed7b9f49b78eddce
Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/29779
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Field 'OEMID' & "OEM Table ID" are related to DSDT table
not to mainboard.
So use macro to set them respectvely to "COREv4" and
"COREBOOT".
Change-Id: I060e07a730e721df4a86128ee89bfe168c69f31e
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/29790
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: David Guckian
We need to default this to low so the speakers don't activate in S3.
BUG=b:118248953
TEST=Used a scope to look at the line and made sure depthcharge still
beeps.
Change-Id: I70d2f4a3261d212b62e784fa7414e45b1d575612
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Reviewed-on: https://review.coreboot.org/c/29783
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
We are seeing problems (interrupt storm) with using the same gpio for
FP MCU wake and irq signals. Reverting back to using separate gpios
for wake and irq until we resolve the issue.
BUG=b:119447525, b:115706071
BRANCH=Nami
TEST=Run powerd_dbus_suspend from kernel and make sure see DUT drop
into S0ix in the EC console. Also, unlock from lock screen with
fingerprint.
Change-Id: Id7987f28526256808b8ed49e66f66298f7cdbcee
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/29665
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Vincent Wang <vwang@google.com>
The dependencies of CONSOLE_SERIAL and DRIVERS_UART were somehow
backwards. Fix that. Now, CONSOLE_SERIAL depends on DRIVERS_UART,
because it's using its interface. The individual UART drivers
select DRIVERS_UART, because they implement the interface and
depend on the common UART code.
Some guards had to be fixed (using CONSOLE_SERIAL now instead of
DRIVERS_UART). Some other guards that were only about compilation
of units were removed. We want to build test as much as possible,
right?
Change-Id: I0ea73a8909f07202b23c88db93df74cf9dc8abf9
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/29572
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
DSDT revision is =1 for ACPI v1 and =2 for greater ACPI version.
This will cause the AML interpreter to use 32-bit integers and math
if the version is 1, and 64-bit if the version is >=2.
Current spec version is 2 for ACPI 6.2-a.
Change-Id: I77372882d5c77b7ed52dcdd88028403df6f6fa7f
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/29626
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Update passive temperature threshold value from 50C to 52C and
critical temperature threshold from 90C to 80C for TSR1 sensor.
BUG=b:79779737
TEST=Build and verified on Bobba/Bobba360/Sparky/Sparky360 boards
Change-Id: Iffef8afe0f1c6c80a6ae8ecb831aaf749443980e
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/29264
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change adds ACPI properties for WDT8752A device.
BUG=b:117174180
BRANCH=master
TEST=Verify touchscreen on delan works with this change
Change-Id: Id1484a482de6282c97f3aac329f217bbcb7dbd18
Signed-off-by: Ivy Jian <ivy_jian@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/29656
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
GPP_D6 needs to be inverted to enter S0ix because FPMCU_INT_L is
active low. Keeps device awake otherwise.
BUG=b:119447525, b:115706071
BRANCH=Nami
TEST=Run powerd_dbus_suspend from kernel and make sure see DUT drop into
S0ix in the EC console.
Change-Id: Iad5df124e2439bbdc078d6a33f8d0510d25ecf6f
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/29650
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Setting sku_id() is not enough to get a value to show up in the SMBIOS
tables, it also needs to be returned as a string for the table creation
to consume. This change defines the smbios_mainboard_sku() function
and returns a string constant of "sku#" as expected.
Change-Id: I03013bab89d53d1eba969c6ffb7e95fcbb315a81
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/29649
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Trent Begin <tbegin@google.com>
GPIO's that use GPI_APIC setting with DEEP causes an IRQ storm after
S3 resume. GPIOs that fire IRQs via IOAPIC need to get their logic
reset over PLTRST to prevent IRQ storm after S3 resume and hence
configuring GPP_F10 (HP_IRQ_GPIO) to use PLTRST.
BUG=none
TEST=none
Change-Id: Idc6c42cb4dc6e8eb368d605c83f584f4c69077dc
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/29540
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: caveh jalali <caveh@chromium.org>
Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
With this change, coreboot thinks we're running at 1MHz:
DW I2C bus 2 at 0xd1133000 (1000 KHz)
Elan eKT3644 IC Specification (trackpad) requires:
Low Time larger than 500ns (61 * 8.3ns = 506ns).
High Time larger than 260ns (32 * 8.3ns = 265ns),
Data Hold_time larger than 0ns.
Start Condition Hold time larger than 250ns.
Rise/Fall time of less than 120ns.
HCNT controls both High Time and Start Condition Hold time.
LCNT controls Low Time.
SDA_HOLD controls Data Hold Time.
P2 Atlas "Rise time" is 90ns and "Fall time" is 32ns and tuned
using resistors on the board and must be considered when
adjusting any of the parameters since these times are all measured
at 30 or 70% of base and peak voltages (0v/1.8v).
The eKT3644 requirements are met with LCNT=69, HCNT=33, SDA_HOLD=20
which yields the SCL at around 950KHz - suboptimal but compliant.
Lower LCNT or HCNT results in "lost arbitration" errors or not complying
with eKT3644 requirements.
Verified by gaggery.tsai@intel.corp-partner.google.com.
Scope shots posted here:
https://b.corp.google.com/issues/78601949#comment177
BUG=b:78601949
BRANCH=none
TEST=Farzam provided test points on track pad for SCL/SDA/GND.
Waveforms measured with oscilloscope and screen shots attached
to bug (comment #177, #155, #100).
Operate trackpad/touchscreen
Review dmesg (kernel) output for correct speed, parameters, and
no errors (e.g. "lost arbitration" or "host controller timeout")
Change-Id: Iaf42ba7b8818b7cd9c8dcc657823dac705659d38
Signed-off-by: Caveh Jalali <caveh@chromium.org>
Signed-off-by: Grant Grundler <grundler@chromium.org>
Tested-by: gaggery.tsai@intel.corp-partner.google.com
Tested-by: grundler@chromium.org
Reviewed-on: https://review.coreboot.org/29553
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Gaggery Tsai <gaggery.tsai@intel.com>
Only input from the BJ port is wired to VSYS on Kalista. VBUS from
USB-C is for output only. In other words, Kalista is a source only
device from a USB/PD perspective.
This patch disables EC-EFS, which would be needed for the EC to jump
to RW to get PD power before the AP boots. Kalista will be always
supplied enough power to boot the AP through the BJ port.
CQ-DEPEND=CL:1330171
BUG=b:118386511
BRANCH=none
TEST=Boot Fizz. Verify normal boot, soft sync, recovery mode work.
Change-Id: Icd18662ae1e76f35eb9bcd521b1951aacc713252
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://review.coreboot.org/29564
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Zhuohao Lee <zhuohao@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
GPP_D0 is NC in 1st SKU board design, so we should control GPP_D0
for only 2nd SKU.
BUG=none
BRANCH=poppy
TEST=emerge-nautilus coreboot
Change-Id: Ifd85693c9155ed960f0c794d4b83fe8863b77134
Signed-off-by: Seunghwan Kim <sh_.kim@samsung.com>
Reviewed-on: https://review.coreboot.org/29631
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The GPP_E1 gpio was incorrectly being defined as a no-connect.
Configure GPP_E1 for the WLAN_WAKE_L signal as per the schematic.
BUG=b:119508897
TEST=Build and flash nocturne, boot nocturne and
1) Verify nocturne can successfully suspend/resume from S3 and S0ix.
2) Verify wake from wlan wakes device from S3 and S0ix.
To do so,
a) as root, execute "iw phy phy0 wowlan enable disconnect" on DUT
b) connect DUT to mobile hotspot
c) sleep device via "powerd_dbus_suspend"
d) turn off hotspot, verify DUT wakes from S0ix
e) enable hotspot again
f) connect DUT to hotspot
g) sleep DUT via "sudo echo mem > /sys/power/state"
h) turn off hotspot, verify DUT wakes from S3
Change-Id: I4efb4f6d601e172ae4807901e3bd4c9954319f80
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/29630
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Rename EC_ENABLE_TABLET_EVENT config as EC_ENABLE_MULTIPLE_DPTF_PROFILES
since it aligns with the use-case.
BUG=b:118149364
BRANCH=None
TEST=Ensured that the expected DPTF table are loaded in different
modes (base attached/detached and clamshell/360-flipped) on Soraka and
Nautilus.
Change-Id: If147f1c79ceaaed00e17ec80ec6c912a8f7a8c2e
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/29261
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Remove the SmbusEnable parameter from all Cannon Lake mainboards.
Instead this will be determined by the enable state of the SMBUS
PCI device.
Change-Id: I7ece6768da4c517747af12a07012583575816ae1
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/29551
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This change updates the configuration of EC_SYNC IRQ to be level
triggered to match the EC behavior.
Change-Id: I8e3cb2ae8016ea183d9067697aa5d4b9caa2d07e
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/29576
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Change tcc offset from 0 to 10 for fleex.
Refer to b:117789732#1
BUG=b:117789732
TEST=Match the result from TAT UI
Change-Id: I481526ab10a16a33fe0cf9528b52b8524e012451
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/29413
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
1. Add two parameters for panel initialization timing.
> lvds_poseq_varybl_to_blon
> lvds_poseq_blon_to_varybl
2. The BL_PWM is controlled by APU_EDP_BKLTEN_L/APU_DP_VARY_BL/
EDP_BKLTEN_L, so move APU_EDP_BKLTEN_L to early init stage,
and be enabled depends on SKU, thus we can control the delay
time by config APU_DP_VARY_BL.
BUG=b:118011567
TEST=emerge-grunt coreboot.
Change-Id: Ib20c48813b208d697b950b2f02a70a690e483fdb
Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/29469
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
GPIOs that use GPI_APIC setting with DEEP can cause an IRQ storm after
S3 resume. GPIOs that fire IRQs via IOAPIC need to get their logic
reset over PLTRST to prevent IRQ strom after S3 resume.
For sarien/arcada these are all runtime IRQs only, not wake capable.
Change-Id: Iec3706a3b47b54abbacd06081910f389979c330f
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/29539
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Select the option to disable eSPI when ACPI is enabled so the EC
is unable to assert an SMI when booted into the OS. There is a
kernel driver that implements the same mailbox interface so it
cannot also be used by the SMI handler.
Change-Id: I8bafc749f22aed5595e19e773762ee8b038950b9
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/29536
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
GPIO's that use GPI_APIC setting with DEEP causes an IRQ storm after
S3 resume. GPIOs that fire IRQs via IOAPIC need to get their logic
reset over PLTRST to prevent IRQ storm after S3 resume and hence
configuring GPP_D9 and GPP_D10 to use PLTRST.
BUG=b:119202293
TEST=none
Change-Id: I98d71100f28fb9bae05db3fb7d9afcb3f81beb43
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/29538
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
GPP_C11 (FPMCU_INT_L) was set to DEEP, causing problems with S3.
Changed GPP_C11 configuration to use PLTRST instead.
BUG=b:114196791
TEST=Build, flash, boot nocturne, log in to kernel and execute
the following two commands and verify it passes :
echo 0 > /var/lib/power_manager/suspend_to_idle && restart powerd
sudo suspend_stress_test -c 2
Change-Id: I008532fce963c51a435378001440ac72b5ebfffc
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/29429
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
add the memory parts as ram id 10:
hynix_dimm_H5ANAG6NAFR-UHC
BUG=b:113983573
BRANCH=Nami
TEST=emerge-nami coreboot chromeos-bootimage
Change-Id: I137259b88f39779768a58959a2dcc565645eee6d
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/29524
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This change adds a sku_id() function that returns a static value to
differentiate the sarien and arcada boards.
Change-Id: I1fecc675573a6aece7188aae9370733068d45dbf
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/29486
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This changes uses drivers/intel/wifi chip for CNVi device to ensure that:
1. Correct device name shows in ACPI name space
2. Correct wake up shows in cat /proc/acpi/wakeup
3. Remove cnvi.asl from soc/intel/cannonlake
Change-Id: Ic81de2dce6045ced913766790a40ed19119f5118
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/29399
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Some variants of nami will have a fingerprint MCU.
BUG=b:118503113
BRANCH=Nami
TEST=None (build and boot, but no hw yet)
Change-Id: I446dc09cdf7f84a801723cb403d2de80e0997c65
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/29297
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
WWAN start-up control requires RESET# assert after FULL_CARD_POWER_OFF#
set to high more than 10 ms, so force RESET#(GPP_D21) to low at
bootblock stage to match the sequence.
BUG=N/A
TEST=Boot up Sarien/Arcada board, check WWAN get detected as USB
devices through lsusb.
Change-Id: I36eb841a2e8f2b36771d20577314a7451fbee133
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/29430
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
This change removes the function defintions from variant
so that the weak definition in baseboard can be used.
Refer to CL:813944.
BUG=none
BRANCH=master
TEST=Build and boot on DUT
Change-Id: I561414fcc94e3c812bb88730df9b94e332c61781
Signed-off-by: David Wu <David_Wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/29368
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Use GPIO_134 as the EC sync interrupt and provide this value
to the embedded controller to be exported to the OS.
BRANCH=none
BUG=crbug:896347, b:118443377
CQ-DEPEND=CL:1298699
TEST=verify sensor events coming in on a reworked board
with companion EC and kernel patches
Change-Id: I41333cabe97bc8b0d59e19d84366f2ea2a59e026
Signed-off-by: Enrico Granata <egranata@chromium.org>
Reviewed-on: https://review.coreboot.org/29278
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Get board id from AUXIN4 and RAM code from AUXIN3.
BUG=b:80501386
BRANCH=none
TEST=AUXIN4 is 0.074v and AUXIN3 is 0.212v on P0.
AUXIN4 is 0.212v and AUXIN3 is 0.212v on P1.
Change-Id: I50533e851d2fae66ae8c5e4e1aa36708d9058e94
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/29062
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
The Sarien mainboard uses the newly added Wilco EC.
- enable CONFIG_EC_GOOGLE_WILCO
- add the device and host command ranges to the devicetree
- have the mainboard SMI handlers call the EC handlers
- add EC and SuperIO devices to the ACPI DSDT
- call the early init hook for serial setup
Change-Id: Idfc4a4af52a613de910ec313d657167918aa2619
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/29411
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Add a variant of the Sarien board called Arcada. This is currently
very similar to Sarien with differences in PCIe, USB, and GPIO usage.
Change-Id: I432d2ba99558e960d4e775c809cc8bf6aa1a56bf
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/29410
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Sarien is a new board using Intel Whiskey Lake SOC. It also uses
the newly added Wilco EC, enabled in a separate commit.
Sarien is not a true reference board, it is just one variant of
a very similar design. For that reason it is not considered the
baseboard but rather a standalone variant.
Change-Id: I2e38f617694ed2c2ef746ff8083f2bfd58cbc775
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/29409
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The function `acpi_fill_madt()` is identical among all the Lynx Point
boards and sb/intel/bd82x6x, so share a common function between them.
Earlier Intel platforms have similar implementations of this function.
The common implementation might only need minor alterations to support
them.
Tested on an ASRock H81M-HDS and Google Peppy (variant of Slippy). No
issues arose from this patch.
Change-Id: Ife9e3917febf43d8a92cac66b502e2dee8527556
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/29388
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
The platform.asl file is copied from sb/intel/bd82x6x, and also matches
the contents deleted from each mainboard's platform.asl.
Tested on an ASRock H81M-HDS and a Google Peppy board (variant of
Slippy). No issues arose from this patch.
Change-Id: I539e401ce9af83070f69147526ca3b1c122f042c
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/29386
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Change the variant name from kalista to karma.
According to the CL:1298319, the baseboard name is kalista
and the board name is karma.
BUG=none
BRANCH=master
TEST=emerge-kalista coreboot chromeos-bootimage
Change-Id: Idea295cc14249721a6dc0fc4e2ef6470d43e16eb
Signed-off-by: David Wu <David_Wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/29314
Reviewed-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
According to syndra thermal table, PL2 need to check cpu id.
Set up syndra PL2 value.
1. KBL_U PL2 is 25w.
2. KBL_R PL2 is 29w.
Refer to b:116836990#comment10.
BUG=b:116836990
TEST=The thermal team verify OK
Change-Id: I766a886121a089683565608252b4c176c70e88a3
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/29269
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Shelley Chen <shchen@google.com>
Unfortunately Stoney has an issue where enabling the IOMMU causes
a 10%-50% decrease in the integrated graphics performance. It is
also disabled by default on other stoney platforms.
BUG=b:118612241
TEST=Verify that IOMMU is disabled.
Change-Id: Ia396c7227cb21461ec8afbdf746721d4fb28083d
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/29342
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Variants of Nami need to accommodate single channel DDR. Will use
GPP_D10 on nami for identification. GPP_D10 will return 1 when device
is using single channel DDR and 0 when using dual channel DDR.
BUG=b:117194353
BRANCH=None
TEST=dmidecode | grep Channel and make sure that the correct number of
channels gets returned.
Change-Id: If86ab2c5404c4e818ce496ea935227ab5e51730a
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/29233
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In function write_pirq_routing_table(), the function name is used in a print
string. Use __func__ instead.
BUG=b:117642170
TEST=Build grunt.
Change-Id: Ibf8673c5b2cda1105aae1edb46f6589d55208c50
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/29245
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
This change enables override device tree for Fizz to allow variants to
provide their own overrides and also moves I2C5 realtek node to
fizz/overridetree.cb since it doesn't apply to some variants being
added for Fizz.
Change-Id: Ia1a069fc539b51a22882ef94b55baf5bf7cd302f
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/29242
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: David Wu <david_wu@quanta.corp-partner.google.com>
Get recovery mode switch from EC and pass it to payload.
BUG=b:80501386
BRANCH=none
Test: Boots correctly on Kukui.
Change-Id: Ib92afca885e5a97ec4646f55f2279ef56a61af5a
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/29190
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Liara auto restart issue is caused by memory access error and consequent
kernel panic. To solve this issue, revert the CL:1243666 (Disable
NbP-state on Liara) and use 2T mode instead.
BUG=b:116082728
TEST=verify the 2T mode is enabled/boot into ChromeOS and no auto restart/run
memtester passed 10 cycle.
Change-Id: I3a96276d88ffb70530d72b15c07b59a01cc6209a
Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/29179
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
1. Update PSV values for cpu and sensers.
2. Change PL1 min value from 3w to 4.5w.
3. Change TSR2 TRT source from charger to CPU.
Refer to 112448519#comment31.
BUG=b:112448519
TEST=Build coreboot for Octopus board
Change-Id: I7c7df0f54374fdaa4cf57d5c255d841d7db38cfc
Signed-off-by: John Su <john_su@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/29146
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
This change uses CRFP ACPI name for FP device since user space
utilities expect this name for triggering different actions.
BUG=b:112974410
BRANCH=nocturne
Change-Id: I63309227c916b43917e529c223cf738fc3baa209
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/29231
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
On rammus, set GPIO GPP_C22 to 1 for touchscreen power on.
And add touchscreen device "PNP0C50" to I2C0.
According to touchscreen spec, device power on initialization takes
105 ms, so set "generic.enable_delay_ms" to 120.
We found there is i2c error log pop up when we set delay
time to be 110ms or 105ms. If we set delay time to be
120ms. System will not pop up i2c error log.
BUG=b:115944726
BRANCH=master
TEST=emerge-rammus coreboot chromeos-ec chromeos-bootimage
Flash FW to DUT, and make sure touchscreen works.
Change-Id: Ibce552d04991e85c99ae3a0a92455fc747d9fced
Signed-off-by: YanRu Chen <kane_chen@pegatron.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/28598
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This change uses DIMM_INFO_PART_NUMBER_SIZE to decide the size of
part_num_store that holds the number of DRAM part. It ensures that
host advertises the supported size to read part number from the EC.
BUG=b:115697578
Change-Id: I8439a301fc037b0acdc8b1226ad04d2f363838ef
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/29241
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Jett Rink <jettrink@chromium.org>
