In ram stage, all code flow should be tied to the resource allocator.
Stuff that has to happen before everything else goes into the mainboard
enable function in mainboard.c. This patch empties the main() wrapper
around hardwaremain.c, allowing to get rid of this special case in the
ARM port.
Change-Id: Ide91a23f1043b64acf64471f180a2297f0f40d97
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3638
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
We've got enough of a handle on this to realize some things:
drm_dp_helper.h is by design device and architecture independent
i915.h is common to most intel graphics chipsets going back several years
i915_reg.h is as well
Move these files to src/include/device, and adjust the .c files accordingly.
Change-Id: I07512b3695fea0b22949074b467986420783d62a
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3637
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Add three functions to edid.c:
void set_vbe_mode_info_valid(struct edid *edid, uintptr_t fb_addr)
takes an edid and uintptr_t, and fills in a static lb_framebuffer struct
as well as setting the static vbe_valid to 1 unless some problem
is found in the edid. The intent here is that this could be called from
the native graphics setup code on both ARM and x86.
int vbe_mode_info_valid(void)
returns value of the static vbe_valid.
void fill_lb_framebuffer(struct lb_framebuffer *framebuffer)
copies the static edid_fb to lb_framebuffer.
There is now a common vbe.h in src/include, removed the two special ones.
In general, graphics in coreboot is a mess, but graphics is always a
mess. We don't have a clean way to try two different ways to turn on
a device and use the one that works. One battle at a time. Overall,
things are much better.
The best part: this code would also work for ARM, which also uses EDID.
Change-Id: Id23eb61498b331d44ab064b8fb4cb10f07cff7f3
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3636
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
These are not specific to Intel. Further work needs to be done to
combine these with MMCONF_SUPPORT in arch/io.h.
Change-Id: Id429db2df8d47433117c21133d80fc985b3e11e4
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3502
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This code is the initial version of FUI for haswell and wtm2.
The code is simplified from before in many ways. I've gotten rid of
the opcode table, because it obscured meaning and I don't think it is
needed any more. Register sets, mainly used for reset, are just lines
of code -- not many of them. There are a bunch of not-yet-documented
registers here; the VBIOS seemed to think they were necessary and
testing shows they seem to be right.
As a bit of added paranoia, we always include the VBIOS code as our
emergency recovery path. You have to run it now anyways, so this is no
regression from our current situation; and, if all goes well, in a
week (or so), you'll never have to run it again, but like the Force
and nose hair, it will be with you always.
The code can return in three ways. The first, best way is success:
panel is up and the VBIOS need not run. The second mode is that we
tried to light up the panel but could not, for some reason, but will
return with the panel partly up. In this case, it's ok not to power
cycle the panel. The third, worst case, which will NEVER happen, ha
ha, is that we have to turn the panel off and wait the required 600ms
for it to cycle. Life sucks sometimes. This failure mode is in the
'hang on we're going to fix it' category now that we have ramstage in
RW.
The Big Goal here is to create something other coreboot ports can use
as well. The guys doing the x60 report that the link FUI works,
without too many mods, on that chipset, so it seems Intel is keeping
things from changing too much over time.
Also, again, please note: this and the next 3 versions will ALWAYS fail.
The goal is to verify the correctness of the recovery path.
The bizarre tab-space formatting in drm_dp_helper.h is from the original,
as in i915_reg.h
Change-Id: I6ecf454633029d185c29d470980b5a0f3114a8ce
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3635
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This lights up the display. We don't get graphics but we are missing the gttsetup
at this point, so that is no shock. The real shock is that anything works at all.
Change-Id: I03fc470334e96878aeb8465044b3cc9c90378735
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3634
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Change all PCI configuration accesses to MMIO on two boards
with i5000 chipset. To enable MMIO style access, add explicit
PCI IO config write in the bootblock.
Change-Id: I26f1c2da5ae98aeeda78bdcae0fb1e8c711a3586
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3601
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
I missed the board with gm45 when I moved MMCONF_SUPPORT lines.
Also, the intel/i3100 does not have MMCONF_SUPPORT implemented
even though it was previously selected for intel/eagleheights board.
Change-Id: I9c7f6b0a150b4d54288a1e015277b9d98467fca4
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3598
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Change all PCI configuration accesses to MMIO on all boards
with SandyBridge and IvyBridge. To enable MMIO style access,
add explicit PCI IO config write in the bootblock.
Change-Id: I8f957a80bf57df000897c5a080dd5ff131b1ec0d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3576
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.huber@secunet.com>
Move/remove MMCONF_SUPPORT reference under mainboard Kconfig, as
that feature originates from northbridge and cannot be disabled
for a single mainboard.
Change-Id: I6d6861079876ddddaff90b10f18edb6936e93bd0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3589
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Set up the pinmux to enable the pins and the clocks for whichever UART is
currently configured.
Change-Id: Iac13f16d9d84320555b99734ea83eafd0a2803fe
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3573
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Thanks to Bruce's great work, we can finally drop this workaround.
Change-Id: Ie92d1e53ef867fa34aa2489ccfb682d73195b213
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/3569
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Users of mptable_write_buses() pass two pass-by-reference
parameters reflecting a maximum bus number and a search bus
number. These bus numbers are expected to be held in "int"
variables and are updated by the function. Both of the
Supermicro boards define the search bus number as a
byte value in mptable.c.
For now, change the two Supermicro boards to use "int"
to hold the search bus index.
Change-Id: Ie71850719c1fa3cda0ac9c8773bb80650de95c70
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3546
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Fix a bunch of compiler-generated warning messages. These fixes are
mainly braces for grouping initializers. These changes are not
intended to change any code functionality. There are two changes where
function prototypes are added, and two cases where unused variables are
eliminated.
Change-Id: I93cef8899170b5575e7fb7c55181b381a7bcd9d8
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3545
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The existing code for setting Azalia configuration assumes that
the configuration bits are contiguous within a single byte and
can be set using a byte copy addressed into the lowest 2-bit
subfield.
The fix in Family 14 defines a union that can be addressed as a
byte to overlay the bit fields. Since the offset of the four
subfields is not necessarily fixed, change the code to initialize
each of the four subfields individually.
Change-Id: I1dff20bb8bd3e1bcd8b4e6b0537e20779d2a3521
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3544
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Copy a type cast from the other cases of the same switch statement
to eliminate compiler warning messages.
Change-Id: I8d0a88892f6a5f8e43227ab5f830041894b07f6a
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3543
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
On Dinar, H8SCM, and H8QGI, add <cpu/amd/amdfam15.h> as an
include to pick up the prototype definition of get_bus_conf().
Change-Id: Ie4887670ac52aa194745881362df19cd1d75773e
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3542
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This requires a new system agent binary (v6 / v11 on haswell).
Note that the existing system agent binaries are long time obsolete
and won't work with current coreboot, so this update is overdue.
Change-Id: I48d8649576ca84d2b85ab082ce06f3462e189059
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/3568
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
BIOS write protects 8 bytes of CMOS, which nvramtool can't cope with.
This makes initial installation harder, so just mark those as reserved
to work around the issue.
Change-Id: I210861dff8572e226a0f250556a3b811671ea8f2
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/3531
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
For iwave/iWRainbowG6 using intel/sch, MMCONF_BASE_ADDRESS was unused
and different from hardware setting. Change that to match hardware
programming.
Change-Id: I3324b7ea0e6f092206d4b6b791476d538e826657
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3507
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
There are no files to build left under AMD nortbridge/x/root_complex
directories. For some cases, even the Kconfig file was no longer sourced.
Remove all such references and empty files.
For devicetree.cb treat component paths with "/root_complex" in them valid
even when the directory does not exists. This is because AMD boards us this
dummy chip component as the root node in their devicetree.cb.
The generated devicetree file static.c remains unchanged.
Change-Id: I9278ebb50a83cebbf149b06afb5669899a8e4d0b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3434
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
The IOMMU needs IRQs assigned. So add those.
Change-Id: Ic9f02e28aac593cddf7d222a8abb780a10572d32
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Reviewed-on: http://review.coreboot.org/3318
Tested-by: build bot (Jenkins)
Reviewed-by: David Hubbard <david.c.hubbard+coreboot@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
In commit Rudolf Marek discovered, that it is not uniformly written. As
»ASL names are not case-sensitive and will be converted to upper case.« [2]
this change does not have any functional change.
The following command was used to create this patch.
$ git grep -l 'package()' src/mainboard | xargs sed -i 's,package(),Package(),'
[1] http://review.coreboot.org/#/c/3318/
[2] http://www.acpi.info/spec40a.htm
(18.2.1 ASL Names)
Change-Id: I1784dbc50936a1ef9d4376209a3c324ef1fb85cf
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3516
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
This commit was tested on qemu with and without CONFIG_DYNAMIC_CBMEM
by running cmbmem -c once booted. The qemu command that was used was:
qemu-system-i386 -bios ./build/coreboot.rom -serial stdio -hda ../virt/parabola.img
Note that using CONFIG_RELOCATABLE_RAMSTAGE make it fails like that:
Loading image.
CBFS: Decompressing stage fallback/coreboot_ram @ 0x3ffbefc0 (184400 bytes)
Loading module at 3ffbf000 with entry 3ffbf000. filesize: 0x18db8 memsize: 0x2c050
Processing 1703 relocs with adjust value of 0x3ffbe000
FATAL: Essential component is missing.
However without CONFIG_RELOCATABLE_RAMSTAGE set it boots fine.
Change-Id: I633a8c3832eee4e8bed244940fdc370b98dd26f0
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Reviewed-on: http://review.coreboot.org/3504
Reviewed-by: Aaron Durbin <adurbin@google.com>
Tested-by: build bot (Jenkins)
Collect early timestamps in T60's romstage like some newer boards do.
This should also work on X60s (and other ICH7 based systems with
EARLY_CBMEM_INIT).
Change-Id: I3b2872dd7423f3379ff3b68ad999523ec35fc08e
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: http://review.coreboot.org/3499
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
All 3 boards with AGESA_HUDSON had HAVE_HARD_RESET with the reset.c
file already placed under southbridge/.
All 15 boards with CIMX_SBx00 had HAVE_HARD_RESET with functionally
identical reset.c file under mainboard/. Move those files under
respective southbridge/.
Change-Id: Icfda51527ee62e578067a7fc9dcf60bc9860b269
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3486
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Confusingly, romstage compiled in different copy of soft_reset()
than ramstage. Use source in reset.c for both.
Change-Id: I2e4b6d1b89c859c7cf5d9e9c8f7748b43d369775
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3487
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
The chip component is unconditionally selected for the mainboard
so these uses are superfluous.
Change-Id: I84b053ab47f7b1f68e88d968cf305e24bc95f4da
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3485
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
CONFIG_HUDSON_XHCI_ENABLE will control the XHCI flags in the
amd/parmer and asus/f2a85-m mainboards. The XHCI ports on
amd/thatcher are not wired to USB jacks so always disable the flags.
This was tested on amd/parmer using a USB 3.0 thumbdrive.
Change-Id: I596b040fec30882d8d4dee34ab9f866dc1f8896b
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/3465
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Add support for the new q35 chipset emulation
added in qemu 1.4.
Change-Id: Iabfaa1310dc7b54c9d224635addebdfafe1fbfaf
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-on: http://review.coreboot.org/3430
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
So the pci allocation code knows where memory is and doesn't
try map pci devices there. We also don't have to check for
overlaps between pci hole and memory then.
Change-Id: I5eaea0e4d21210719685860fa1f16ca7b2137cde
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-on: http://review.coreboot.org/3491
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Prepare tree for adding q35 support:
Move emulation/qemu-x86 to emulation/qemu-i440fx.
Rename some stuff to include 'i440fx'.
Change-Id: Ib8c58175c5734cfcda1b22404ef52c09d38f0462
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-on: http://review.coreboot.org/3429
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This issue can be reproduced in Linux by the following steps:
1) use pm-suspend to suspend.
2) use USB keyboard to wake up.
3) use pm-suspend to suspend. FAIL To SUSPEND.
The cause of this issue is:
USB devices use bit 11(0x0b) of GP0_STS represents S3 wake up event,
but this bit is not clear after wake up. So OS thinks there is a
wake up signal and wake up immediately.
In this patch, I add AcpiGpe0Blk using MMIO access and write 1
on bit 11. Write 1 to clear as spec says.
I have tested on Thatcher
The same change was done for AMD Parmer in commit »AMD Parmer:
fix issue 'S3 fails to suspend after wake up from USB keyboard'
(03901124) [1].
[1] http://review.coreboot.org/#/c/3347/
(Change-Id: Iec3078bf29de99683e7cd3ef4e178fbeb4dc09c1)
Change-Id: Iaef39237497ef896d0f186e8f5522222c0ce6cb7
Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com>
Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/3374
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This ancient board with Intel e7505 invalidates cache while it does HW
scrubbing for ECC in romstage. This breaks usbdebug console and prevents
system from booting.
If both EARLY_CONSOLE and USBDEBUG are selected, skip ECC scrubbing under
these rare conditions to boot system.
Change-Id: I6cb43bf69af54119f4a582dcaf498dd941d4c62d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/3385
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Now that the ROM size is decoupled from the size of the on chip RAM,
it's size is now only constrained by the size of the medium it's loaded
from and the memory it's being loaded into, probably GBs in both cases.
Making it 4MB is a reasonable compromise between giving the payload lots
of breathing room and wasting space on the source medium which won't be
used.
Change-Id: I80932e0d4ce2dad02c3879345382e7d6ba44503a
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3422
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Until we get serial working, this is a good way to show that coreboot is
running. It can be removed once we have better methods.
Change-Id: I62d25e52aa88a97aba4c959538d680b67a0bbbb2
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3329
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
EPIA-M850 can now boot linux. For a list of issues, see:
http://www.coreboot.org/VIA_EPIA-M850
That's all folks.
Change-Id: I7624944dbc05fbf3019897a116954d71dfda0031
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/1228
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Keep in mind that we can _NOT_ read back the current state
of the LEDS as some crazy FPGA designer wanted it that way.
Change-Id: I5cd1ac598072318b3234d1ec35a79271655b46ac
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-on: http://review.coreboot.org/3271
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Without that commit, with CONFIG_PCI_OPTION_ROM_RUN_YABEL,
The VGA option rom doesn't init the right display:
it initializes the external display, where we have
a black scren(with backlight on).
This commit is based on the code of mainboard.c in
src/mainboard/roda/rk886ex.
Change-Id: I8457aaf0503e0efdf0fcba9ff5e8a07ac04c5ca6
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Reviewed-on: http://review.coreboot.org/3265
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
First copy over from SeaBIOS git repo, then adapt for coreboot:
Disable cpu/pci hotplug bits. Disable dynamic pci window.
Both depend on stuff in the SSDT tables created by SeaBIOS.
Bits are left in, but deactivated via #if 0, so it's easier
to see the differences when diffing the coreboot tables with
the SeaBIOS tables.
Adapt dsdt DefinitionBlock.
Enable acpi table generation in acpi_tables.c.
With this patch linux boots successfully with ACPI enabled.
It's not bug-free though. Missing cpu detection leads to
funky messages like this one:
weird, boot CPU (#0) not listed by the BIOS.
and SMP most likely wouldn't work either.
Change-Id: Ic3803a6f1ef6d54c11cc4ca3844d3032a374ae6b
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-on: http://review.coreboot.org/3342
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
The DDI connector table and the PCIe Port List lookup table are
copied onto HEAP. This copy is not needed since these are lookup
tables used to define the platform configuration.
Change-Id: If4760f80e08faa8da4fd11337a3812f89cf805f9
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3394
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Add boot cpu to the device tree. Figure the number of CPUs installed
(using the qemu firmware config interface) and add cpu devices for them,
so they show up in all generated BIOS tables correctly. This gets SMP
going.
Change-Id: I0e99f98942d8ca90150b27fc13c1c7e926a1a644
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-on: http://review.coreboot.org/3345
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Needed to make 'register "gpo" = ...' work.
While being at it add comments saying which device is which.
Change-Id: I911d5e4a7b6c7abf4ad73e863ab201e9e55ee0d4
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-on: http://review.coreboot.org/3346
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
qemu has a special device to pass configuration information
from qemu to the firmware. This patch adds initial support
the interface, namely some infrastructure, detection code and
a function to query the number of CPUs.
Change-Id: I43ff5f4fbf12334a91422aa38f514a82a1d5219e
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-on: http://review.coreboot.org/3343
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This reverts commit eed28f97b3.
For whatever reason, the dependencies were lost in Gerrit and the
commit [1] was submitted without its dependencies. As a result
buidling the ASUS F2A85-M fails now [2] and therefore commits
based on this commit fail to pass the buid tests by Jenkins.
[…]
Created CBFS image (capacity = 8387656 bytes)
LINK cbfs/fallback/romstage_null.debug
CC cbfs/fallback/coreboot_ram.debug
coreboot-builds/asus_f2a85-m/generated/coreboot_ram.o:(.data+0x16b9c): undefined reference to `GnbIommuScratchMemoryRangeInterface'
collect2: error: ld returned 1 exit status
make: *** [coreboot-builds/asus_f2a85-m/cbfs/fallback/coreboot_ram.debug] Error 1
make: *** Waiting for unfinished jobs....
coreboot-builds/asus_f2a85-m/mainboard/asus/f2a85-m/buildOpts.romstage.o:(.data+0x3d8): undefined reference to `GnbIommuScratchMemoryRangeInterface'
collect2: error: ld returned 1 exit status
make: *** [coreboot-builds/asus_f2a85-m/cbfs/fallback/romstage_null.debug] Error 1
[…]
Therefore revert the commit to get the tree working again and
submit this patch with its dependencies again.
[1] http://review.coreboot.org/#/c/3317/
[2] http://qa.coreboot.org/job/coreboot-gerrit/6618/testReport/junit/(root)/board/i386_asus_f2a85_m/
Change-Id: I911755884da09eb0a0651b8db07ee2a32e6eaaaa
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3373
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Do the setup for all PCI slots, not only the third.
Also remove the bogus message, as slot 3 may carry
any device, not only NICs.
This makes IRQ setup simliar to SeaBIOS.
SeaBIOS assignments (with patch for logging added,
and a bunch of pci devices for testing purposes):
PCI IRQ [piix]: bdf=00:01.3 pin=1 line=10
PCI IRQ [piix]: bdf=00:03.0 pin=1 line=11
PCI IRQ [piix]: bdf=00:04.0 pin=1 line=11
PCI IRQ [piix]: bdf=00:05.0 pin=1 line=10
PCI IRQ [piix]: bdf=00:06.0 pin=1 line=10
PCI IRQ [piix]: bdf=00:1d.0 pin=1 line=10
PCI IRQ [piix]: bdf=00:1d.1 pin=2 line=10
PCI IRQ [piix]: bdf=00:1d.2 pin=3 line=11
PCI IRQ [piix]: bdf=00:1d.7 pin=4 line=11
Coreboot assignments without this patch:
Assigning IRQ 11 to 0:3.0
Coreboot assignments with this patch:
Assigning IRQ 10 to 0:1.3
Assigning IRQ 11 to 0:3.0
Assigning IRQ 11 to 0:4.0
Assigning IRQ 10 to 0:5.0
Assigning IRQ 10 to 0:6.0
Assigning IRQ 10 to 0:1d.0
Assigning IRQ 10 to 0:1d.1
Assigning IRQ 11 to 0:1d.2
Assigning IRQ 11 to 0:1d.7
Change-Id: Ie96be39185f2f1cbde3c9fc50e29faff59c28493
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-on: http://review.coreboot.org/3334
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
After removing power and the CMOS Battery, putting it back
and booting coreboot we have:
# ./nvramtool -a
boot_option = Fallback
last_boot = Fallback
baud_rate = 115200
debug_level = Spew
hyper_threading = Enable
nmi = Enable
boot_devices = ''
boot_default = 0x40
cmos_defaults_loaded = Yes
lpt = Enable
volume = 0xff
tft_brightness = 0xbf
first_battery = Primary
bluetooth = Enable
The code for handling the invalid CMOS space in mainboard.c
is now useless and so it was removed.
Change-Id: Ic57a14eeeea861aa034cb0884795b0152757bf5b
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Reviewed-on: http://review.coreboot.org/3335
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Move the include before static inline int spd_read_byte().
Change-Id: I4cac4b1f55368041b067422d95c09208e15d0f2d
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-on: http://review.coreboot.org/3368
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
On Asus F2A85-M, the Linux kernel complains that the _CRS method does
not specify the number of PCI busses.
[FIRMWARE BUG]: ACPI: no secondary bus range in _CRS
Just put there 256. This should be part of re-factoring of the whole
ACPI stuff.
The same change was already done for the AMD Brazos (SB800) boards,
based on commit »Persimmon DSDT: Add secondary bus range to PCI0«
(4733c647) [1].
[1] http://review.coreboot.org/2592
Change-Id: I06f90ec353df9198a20b2165741ea0fe94071266
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Reviewed-on: http://review.coreboot.org/3320
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: David Hubbard <david.c.hubbard+coreboot@gmail.com>
- SPI controller base address gets overwritten by SD controller under Linux.
- Reason for overwrite is the SPI base address isn't in a standard BAR and doesn't
get automatically reserved. Solution is to add it as a reserved memory area in
ACPI.
- This issue was found on the ASUS F2A85-M platform. Currently a workaround on this
platform was made as part of: http://review.coreboot.org/#/c/3167/3
- Once approved a follow-on patch for other southbridges using a non-standard BAR for
the spi controller.
Change-Id: I1b67da3045729a6754e245141cd83c5b3cc9009e
Signed-off-by: Steven Sherk <steven.sherk@se-eng.com>
Reviewed-on: http://review.coreboot.org/3270
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This issue can be reproduced in Linux by the following steps:
1) use pm-suspend to suspend.
2) use USB keyboard to wake up.
3) use pm-suspend to suspend. FAIL To SUSPEND.
The cause of this issue is:
USB devices use bit 11(0x0b) of GP0_STS represents S3 wake up event,
but this bit is not clear after wake up. So OS thinks there is a
wake up signal and wake up immediately.
In this patch, I add AcpiGpe0Blk using MMIO access and write 1
on bit 11. I have tested on Parmer.
Change-Id: Iec3078bf29de99683e7cd3ef4e178fbeb4dc09c1
Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com>
Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/3347
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Change `sizeof(type) * n`, where n is the number of array
elements, to `sizeof(variable)` to directly get the size of the
variable (struct, array). Determining the size by counting array
elements is error prone and unnecessary.
Rudolf Marek’s patch »ASUS F2A85-M: Correct and clean up PCIe
config« [1] contains the same change and is ported over. In
the commit message Rudolf makes the following comment.
»Not sure why the copy is needed instead of direct reference.
Maybe it has something to do with CAR?«
Testing on the ASRock E350M1, no regressions were noticed.
[1] http://review.coreboot.org/#/c/3194/
Change-Id: I123031b3819a10c9c85577fdca96c70d9c992e87
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3248
Tested-by: build bot (Jenkins)
Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Change `sizeof(type) * n`, where n is the number of array
elements, to `sizeof(variable)` to directly get the size of the
variable (struct, array). Determining the size by counting array
elements is error prone and unnecessary.
Not sure why the copy is needed instead of direct reference.
Maybe it has something to do with CAR?
These changes are based on Rudolf’s original patch »ASUS F2A85-M:
Correct and clean up PCIe config« [1], where it was just done for
the ASUS board.
[1] http://review.coreboot.org/#/c/3194/
Change-Id: I4aa4c6cde5a27b7f335a71afc21d1603f2ae814b
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3247
Tested-by: build bot (Jenkins)
Reviewed-by: David Hubbard <david.c.hubbard+coreboot@gmail.com>
Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Extra care for the qemu vga should not be needed any more.
Since release 0.12 qemu loads the vgabios into the PCI ROM
bar, so everything works exactly like it does on real hardware.
Change-Id: I4b9bf1244cad437cbe5168600aeee52031456033
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-on: http://review.coreboot.org/3333
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Initial structure of Beaglebone port
Change-Id: Ia255ab207f424dcd525990cdc0d74953e012c087
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3279
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This allows other boards to have the same choice block without confusing
kconfig.
Change-Id: Iea5a7f2d1c263aa7992f504b832ca9c862833c3f
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3293
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
Currently the code in the if statement
if (!byte)
do_smbus_write_byte(0xb20, 0x15, 0x3, byte);
only gets executed if `byte == 0x0`, that means only in the
default case where RAM voltage is 1.5 Volts. But the RAM voltage
should be changed when configured for the non-default case.
So negate the predicate to alter the RAM voltage for the
non-default cases.
To prevent the build error
OBJCOPY cbfs/fallback/coreboot_ram.elf
coreboot-builds/asus_f2a85-m/generated/crt0.romstage.o: In function `cache_as_ram_main':
/srv/jenkins/.jenkins/jobs/coreboot-gerrit/workspace/src/mainboard/asus/f2a85-m/romstage.c:106: undefined reference to `do_smbus_write_byte'
collect2: error: ld returned 1 exit status
make: *** [coreboot-builds/asus_f2a85-m/cbfs/fallback/romstage_null.debug] Error 1
add `southbridge/amd/agesa/hudson/smbus.c` providing the function
`do_smbus_write_byte` to ROM stage in `Makefile.inc`. That can
actually be used after the needed header files are included in a
previous commit.
Change-Id: I89542479c4cf6d412614bcf4586ea98e097328d6
Reported-by: David Hubbard <david.c.hubbard+coreboot@gmail.com>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3200
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
This feature has not been used and was never fully integrated.
In the progress of cleaning up coreboot, let's drop it.
Change-Id: Ib40acdba30aef00a4a162f2b1009bf8b7db58bbb
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/3251
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The following commit
commit 05f3b117dd
Author: Paul Menzel <paulepanter@users.sourceforge.net>
Date: Tue May 14 09:28:26 2013 +0200
AMD Inagua: PlatformGnbPcie.c: Allocate exact needed size for buffer
Reviewed-on: http://review.coreboot.org/3246
changed one calculation for the size of the array PortList[] to
reflect only four elements, but neglected three additional calculations
of the size of the same table.
Correct that by setting the size for four array elements in all four
calculations.
[1] http://review.coreboot.org/#/c/3239/3/src/mainboard/amd/inagua/PlatformGnbPcie.c
Change-Id: Ib66b7b2b388d847888663e9eb6d1c8c9d50b9939
Reported-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3250
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
The following commit
commit d0790694b0
Author: Kerry Sheh <shekairui@gmail.com>
Date: Thu Jan 19 13:18:37 2012 +0800
Inagua: Inagua GNB ddi lanes and pcie lanes config update
Reviewed-on: http://review.coreboot.org/544
assigns lanes 4 and 5 to PCI device number 4, but does not
adapt the rest of the code.
After the commit above, the array `PortList []` only has four
elements, but the buffer size `AllocHeapParams.RequestedBufferSize`
is set to a size as it still has five elements.
Correct that by setting the size for four array elements.
[1] http://review.coreboot.org/#/c/3239/3/src/mainboard/amd/inagua/PlatformGnbPcie.c
Change-Id: I3ff07f308ffd417d2bf73117eda9da2a1a05f199
Reported-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3246
Tested-by: build bot (Jenkins)
Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
These arrays are declared as `static` for AMD SB800 based boards,
so do the same for this generation.
Rudolf Marek just changed `const CODEC_TBL_LIST` to `static const`
in [1]. Adapt all Fam15tn based boards (AMD Parmer, AMD Thatcher,
ASUS F2A85-M) to keep the differences between them small.
[1] http://review.coreboot.org/#/c/3170/3/src/mainboard/asus/f2a85-m/BiosCallOuts.c
Change-Id: I353b38bd8bc77ba500a4b7fe9250e9aa3071c530
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3198
Tested-by: build bot (Jenkins)
To make it easier to fill in the values, place the table
from the BIOS and Kernel Developer’s Guide (BKDG) [1]
as a comment.
[1] http://www.coreboot.org/Datasheets#AMD_Fam15
Change-Id: I218f76e9fa2dc88d47af51ea6c062e315afb0000
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3221
Tested-by: build bot (Jenkins)
In `PlatformGnbPcie.c` AGESA functions are used to reserve memory
space to save the PCIe configuration to. This is the
With the following definitions in `AGESA.h`
$ more src/vendorcode/amd/agesa/f14/AGESA.h
[…]
/// PCIe port descriptor
typedef struct {
IN UINT32 Flags; /**< Descriptor flags
* @li @b Bit31 - last descriptor in complex
*/
IN PCIe_ENGINE_DATA EngineData; ///< Engine data
IN PCIe_PORT_DATA Port; ///< PCIe port specific configuration info
} PCIe_PORT_DESCRIPTOR;
/// DDI descriptor
typedef struct {
IN UINT32 Flags; /**< Descriptor flags
* @li @b Bit31 - last descriptor in complex
*/
IN PCIe_ENGINE_DATA EngineData; ///< Engine data
IN PCIe_DDI_DATA Ddi; ///< DDI port specific configuration info
} PCIe_DDI_DESCRIPTOR;
/// PCIe Complex descriptor
typedef struct {
IN UINT32 Flags; /**< Descriptor flags
* @li @b Bit31 - last descriptor in topology
*/
IN UINT32 SocketId; ///< Socket Id
IN PCIe_PORT_DESCRIPTOR *PciePortList; ///< Pointer to array of PCIe port descriptors or NULL (Last element of array must be terminated with DESCRIPTOR_TERMINATE_LIST).
IN PCIe_DDI_DESCRIPTOR *DdiLinkList; ///< Pointer to array DDI link descriptors (Last element of array must be terminated with DESCRIPTOR_TERMINATE_LIST).
IN VOID *Reserved; ///< Reserved for future use
} PCIe_COMPLEX_DESCRIPTOR;
[…]
memory has to be reserved for the `PCIe_COMPLEX_DESCRIPTOR` and,
as two struct members are pointers to arrays with elements of type
`PCIe_PORT_DESCRIPTOR` and `PCIe_DDI_DESCRIPTOR`, space for these
times the number of array elements have to be reserved:
a + b * 5 + c * 2.
sizeof(PCIe_COMPLEX_DESCRIPTOR)
+ sizeof(PCIe_PORT_DESCRIPTOR) * 5
+ sizeof(PCIe_DDI_DESCRIPTOR) * 2;
But for whatever reason parentheses were put in there making this
calculation incorrect and reserving too much memory.
(a + b * 5 + c) * 2
So, remove the parentheses to reserve the exact amount of memory
needed.
The ASRock E350M1 still boots with these changes. No changes were
observed as expected.
Rudolf Marek made this change as part of his patch »ASUS F2A85-M:
Correct and clean up PCIe config« [1]. Factor this hunk out as it
affects all AMD Brazos and Trinity based boards.
[1] http://review.coreboot.org/#/c/3194/
Change-Id: I32e8c8a3dfc5e87eb119eb17719d612e57e0817a
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3239
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Revert commit f90071faee [1] as
it was merged without its dependencies and therefore the source
tree currently does not build [2][3].
OPTION option_table.h
GEN build.h
SCONFIG mainboard/pcengines/alix1c/devicetree.cb
CC arch/x86/lib/cbfs_and_run.romstage.o
CC arch/x86/lib/memcpy.romstage.o
CC arch/x86/lib/memset.romstage.o
CC arch/x86/lib/rom_media.romstage.o
CC arch/x86/lib/romstage_console.romstage.o
CC console/die.romstage.o
CC console/post.romstage.o
CC console/vtxprintf.romstage.o
CC device/device_romstage.romstage.o
CC lib/cbfs.romstage.o
CC lib/compute_ip_checksum.romstage.o
CC lib/gcc.romstage.o
CC lib/lzma.romstage.o
CC lib/memchr.romstage.o
CC lib/memcmp.romstage.o
CC lib/memmove.romstage.o
CC lib/ramtest.romstage.o
CC lib/uart8250.romstage.o
CC southbridge/amd/cs5536/smbus.romstage.o
ROMCC generated/bootblock.inc
GEN generated/bootblock.ld
make: *** No rule to make target `nvramtool', needed by `coreboot-builds/pcengines_alix1c/coreboot.pre1'. Stop.
make: *** Waiting for unfinished jobs....
OPTION cmos_layout.bin
[1] http://review.coreboot.org/#/c/3229/
[2] http://www.coreboot.org/pipermail/coreboot/2013-May/075864.html
[3] http://qa.coreboot.org/job/coreboot-gerrit/6251/testReport/junit/(root)/board/i386_pcengines_alix1c/
Change-Id: I4764d90c39ccdb4dc7e7a9aef7525c306614e1a8
Signed-off-by: Peter Stuge <peter@stuge.se>
Reviewed-on: http://review.coreboot.org/3245
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: David Hendricks <dhendrix@chromium.org>
This was an early bring-up reference board for ULT but it is no
longer being worked on and was never complete enough to be useful
and I no longer have a board so it is already stale and untested.
All ULT bring-up work has moved to the wtm2 mainboard instead.
Change-Id: If64d61bf7a3fc8c9e16096ffc28fa4128aa99477
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/48897
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/3231
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The format of this function changed but was not updated in
all mainboards. This fixes BaskingRidge and WTM2.
The int15 handler no longer takes a regs structure as an
argument and instead uses global variables. The yabel interface
is now similar enough that we can drop the duplicate handler.
Change-Id: Ia717ae14f99cee6d83ccdb1e26b9d7defe1638c4
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/48896
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/3230
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This option has never had much if any use. It solved a problem over 10
years ago that resulted from an argument over the value or lack thereof
of including all the debug strings in a coreboot image. The answer is
in: it's a good idea to maintain the capability to print all messages,
for many reasons.
This option is also misleading people, as in a recent discussion, to
believe that log messges are controlled at build time in a way they are
not. For the record, from this day forward, we can print messages at all
log levels and the default log level is set at boot time, as directed by
DEFAULT_CONSOLE_LOGLEVEL. You can set the default to 0 at build time and
if you are having trouble override it in CMOS and get more messages.
Besides, a quick glance shows it's always set to max (9 in this case) in
the very few cases (1) in which it is set.
Change-Id: I60c4cdaf4dcd318b841a6d6c70546417c5626f21
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/3188
Tested-by: build bot (Jenkins)
The macros GNB_GPP_PORTx_PORT_PRESENT, GNB_GPP_PORTx_SPEED_MODE,
GNB_GPP_PORTx_LINK_ASPM and GNB_GPP_PORTx_CHANNEL_TYPE are not used.
Change-Id: I5c7b7d45880367dba452ebcd4f01fbd0c15aac22
Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com>
Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/3087
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Apply the following commit to all AMD boards.
commit 935850e082
Author: Stefan Reinauer <reinauer@chromium.org>
Date: Mon May 6 16:16:03 2013 -0700
asrock/e350m1: reduce default stack size
The stack used on the ASRock E350M1 is significantly less than
what we currently set (64k per core). In fact, we use about half
of the default stack size (4k) on core 0 and even less on non
BSP cores [1]:
$ grep stack coreboot_without_patch_but_monotonic_timer.log
CPU1: stack_base 002a0000, stack_end 002afff8
CPU1: stack: 002a0000 - 002b0000, lowest used address 002afda8, stack used: 600 bytes
CPU0: stack: 002b0000 - 002c0000, lowest used address 002bf75c, stack used: 2212 bytes
[…]
Reviewed-on: http://review.coreboot.org/3209
Please note that AGESA seems to define bigger stack sizes. But
these seem to be too much too.
$ git grep STACK_SIZE src/vendorcode/amd
[…]
src/vendorcode/amd/agesa/f14/Proc/CPU/Family/0x14/cpuF14CacheDefaults.c:#define BSP_STACK_SIZE 16384
src/vendorcode/amd/agesa/f14/Proc/CPU/Family/0x14/cpuF14CacheDefaults.c:#define CORE0_STACK_SIZE 16384
src/vendorcode/amd/agesa/f14/Proc/CPU/Family/0x14/cpuF14CacheDefaults.c:#define CORE1_STACK_SIZE 4096
src/vendorcode/amd/agesa/f14/Proc/CPU/Family/0x14/cpuF14CacheDefaults.c: BSP_STACK_SIZE,
src/vendorcode/amd/agesa/f14/Proc/CPU/Family/0x14/cpuF14CacheDefaults.c: CORE0_STACK_SIZE,
src/vendorcode/amd/agesa/f14/Proc/CPU/Family/0x14/cpuF14CacheDefaults.c: CORE1_STACK_SIZE,
[…]
The following command was used to create the patch.
$ git grep -l STACK_SIZE src/mainboard/ | xargs sed -i '/STACK_SIZE/,+3d'
Change-Id: I36b95b7a6f190b64d0639fc036ce2fb0253f3fa1
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3217
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This option has not been enabled on any board and was considered
obsolete last time it was touched. If we need the functionality,
let's fix this in a generic way instead of a K8 specific way.
This was mostly a speedup hack back in the day.
Change-Id: Ib1ca248c56a7f6e9d0c986c35d131d5f444de0d8
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/3211
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
Since this parameter is not used anymore, drop it from
all calls to copy_and_run()
Change-Id: Ifba25aff4b448c1511e26313fe35007335aa7f7a
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/3213
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
it has been unused since 9 years or so, hence drop it.
Change-Id: I0706feb7b3f2ada8ecb92176a94f6a8df53eaaa1
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/3212
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
The stack used on the ASRock E350M1 is significantly less than
what we currently set (64k per core). In fact, we use about half
of the default stack size (4k) on core 0 and even less on non
BSP cores [1]:
$ grep stack coreboot_without_patch_but_monotonic_timer.log
CPU1: stack_base 002a0000, stack_end 002afff8
CPU1: stack: 002a0000 - 002b0000, lowest used address 002afda8, stack used: 600 bytes
CPU0: stack: 002b0000 - 002c0000, lowest used address 002bf75c, stack used: 2212 bytes
Removing the Kconfig variable STACK_SIZE to use the default results
in the following numbers of stack usage.
$ grep stack coreboot_with_patch.log
CPU1: stack_base 00287000, stack_end 00287ff8
CPU1: stack: 00287000 - 00288000, lowest used address 00287da8, stack used: 600 bytes
CPU0: stack: 00288000 - 00289000, lowest used address 0028875c, stack used: 2212 bytes
[1] http://review.coreboot.org/#/c/3154/
(comment May 2 10:21 AM)
Change-Id: Ibdb2102c86094fce3787e3b5a162ca8423de205c
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Tested-by: Paul Menzel <paulepanter@users.sourceforge.net>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3209
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This re-introduces 2fde966 (http://review.coreboot.org/#/c/3177/)
which was reverted due to unsatisfied dependencies.
time.h We Hardly Knew Ye.
This deprecates time.h which is currently only used by Exynos5250 and
Snow. The original idea was to try and unify some of the various timer
interfaces and has been supplanted by the monotonic timer API.
timer_us() is now obsolete. timer_start() is now mct_start() and
is exposed in exynos5250/clk.h.
Change-Id: I8e60105629d9da68ed622e89209b3ef6c8e2445b
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3201
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
1. Move comment for console init to correct place.
2. Start output with capital letter and add full stop at the end.
3. Add missing »)« at the end of description of GPIO 10.
4. Use tabulators instead of spaces.
5. Indent the code automatically using GNU indent [1] with the `-sc`
switch adding stars in front of comment blocks as the good indent
manual documents.
$ indent -linux -sc src/mainboard/lenovo/x60/romstage.c
Leave the numbers left aligned as it is more beneficial to be
able to run indent without adapting the result afterward.
[1] http://www.coreboot.org/Development_Guidelines#Coding_Style
Change-Id: I2fa018ec28ff19d23d68754b565c13a7d7a57355
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3185
Tested-by: build bot (Jenkins)
Reviewed-by: Denis Carikli <GNUtoo@no-log.org>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This reverts commit 2fde9668b4
Somehow this got merged before its dependencies. 3190 must be merged first, followed by 3176. However 3190 will fail while this patch is in. So the situation can't correct itself.
Reverting this until the other two go in.
Change-Id: I176f37c12711849c96f1889eacad38c00a8142c4
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3195
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
If the SD controller is "off" hudson.c won't disable that because,
there is no code for this yet.
The PCI device is still visible and PCI BAR will be allocated
by Linux. Unfortunately it may happen that the particular address
is used by non-standard BAR for SPI controller.
Change-Id: Ied7c581727541e2c81b0b1c2b70fd32de0014730
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Reviewed-on: http://review.coreboot.org/3167
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
time.h We Hardly Knew Ye.
This deprecates time.h which is currently only used by Exynos5250 and
Snow. The original idea was to try and unify some of the various timer
interfaces and has been supplanted by the monotonic timer API.
timer_us() is now obsolete. timer_start() is now mct_start() and
is exposed in exynos5250/clk.h.
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Change-Id: I14ebf75649d101491252c9aafea12f73ccf446b5
Reviewed-on: http://review.coreboot.org/3177
Reviewed-by: Aaron Durbin <adurbin@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Stefan Reinauer suggested 'select UDELAY_LAPIC' did not belong in
f2a85-m/Kconfig. It got there via copy-paste from thatcher/Kconfig
so this commit removes the 'select UDELAY_LAPIC' from both and puts
it in cpu/amd/agesa/family15tn/Kconfig
Since f2a85-m is the only Thatcher board coreboot supports right
now, this should not break any other boards.
Change-Id: I811b579c31f8d259a237d3a6724ad3b17f3a6c3e
Signed-off-by: David Hubbard <david.c.hubbard+coreboot@gmail.com>
Reviewed-on: http://review.coreboot.org/3178
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: build bot (Jenkins)
The "gigabit ethernet controller" (GEC) block was added to AMD
Hudson A55E to integrate ethernet capabilities into an AMD
southbridge.
The GEC is designed to work with B50610 and B50610M gigabit PHY
chips from Broadcom. These parts may not be generally available
in small quantities for embedded development.
The GEC block requires an opaque firmware blob to function. The
GEC blob is controlled by AMD and Broadcom and is not available
from coreboot.org.
This change removes GEC support from AMD Parmer and AMD Thatcher
mainboards since these boards do not have the Broadcom PHY.
AMD has requested that the GEC be hidden for Hudson FCH since
the PHY parts are not generally available. This Kconfig option
can make it appear that this is a viable and supported way to
add Ethernet to an embedded board. It is possible to use the
Hudson GEC block with other PHYs, but this requires development
of a custom GEC blob and a custom Ethernet driver. A custom GEC
blob has been developed for a Micrel PHY, but there is no
accompanying driver.
Change-Id: I7a7bf4d41e453390ecf987c9c45ef2434fc1f1a3
Signed-off-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-on: http://review.coreboot.org/3127
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
It's fine to always start timer even in suspend/resume mode, so we can
move the timer_start() back to the very beginning of boot procedure.
That provides more precise boot time information.
With that timer change, the wake up state test procedure can be simplified.
Verified by building and booting firmware image on Google/Snow successfully,
and then suspend-resume without problem (suspend_stress_test).
Change-Id: I0d739650dbff4eb3a75acbbf1e4356f2569b487d
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/3151
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The firmware media source (SPI1) is already initialized by Exynos iROM.
There is no need to do it again.
Verified by building and booting Google/Snow successfully.
Change-Id: I89390506aa825397c0d7e52ad7503f1cb808f7db
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/3147
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The "console_init" does initialize UART driver (which will setup peripheral and
pinmux) and print starting message. Duplicated initialization can be removed.
Also, console_init (from console.c) is always linked to bootblock (and will do
nothing if CONFIG_EARLY_CONSOLE is not defined) so it's safe to remove #ifdef.
Verified by building and booting on Google/Snow, with and without
CONFIG_EARLY_CONSOLE.
Change-Id: I0c6b4d4eb1a4e81af0f65bcb032978dfb945c63d
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/3150
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Enable `EARLY_CBMEM_INIT` for CBMEM console support by looking how
other boards do this.
This commit is tested by enabling the CBMEM console (`CONSOLE_CBMEM` in
Kconfig) and then in GRUB 2 (as a payload) with the cbmemc command from
the cbmemc module and in userspace with ./cbmem -c. Both worked.
Change-Id: I34618a55ded7292a411bc232eb76267eec17d91e
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Reviewed-on: http://review.coreboot.org/3142
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@google.com>
Tested-by: build bot (Jenkins)
The DDR3 memory initialization (with "mem_reset" set on normal boot) will cause
resume to be unstable, especially when X is running. System may show X screen
for few seconds, then crash randomly and unable to recover - although text
console may still work for a while. Probably caused by corrupted memory pages.
'mem_reset' (which refers to RESET# in DDR3 spec) should be enabled according
to DDR3 spec. But it seems that on Exynos 5, memory can be initialized without
setting mem_reset for both normal boot and resume - at least no known failure
cases are found yet. So this can be a temporary workaround.
Verified by booting a Google/Snow device with X Window and ChromeOS, entering
browser session with fancy web pages, closing LID to suspend for 5 seconds, then
re-opening to resume. Suspend/resume worked as expected.
Also tried the "suspend_stress_test" with X running and finished 100 iterations
of suspend/resume test without failure.
Change-Id: I7185b362ce8b545fe77b35a552245736c89d465e
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/3148
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Add the suspend/resume feature into bootblock and romstage.
Note, resuming with X and touchpad driver may be still unstable.
Verified by building and booting successfully on Google/Snow, and then executing
the "suspend_stress_test" in text mode ("stop ui; suspend_stress_test") in
Chromium OS, passed at least 20 iterations.
Change-Id: I65681c42eeef2736e55bb906595f42a5b1dfdf11
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/3102
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Move board setup procedure to snow_setup_* functions, and Snow board-specific
(wakeup) code to snow_* for better function names and comments.
Verified by successfully building and booting on Google/Snow.
Change-Id: I2942d75064135093eeb1c1da188a005fd255111d
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/3130
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
The "wakeup" procedure will be shared by bootblock and romstage for different
types of resume processes.
Note, this commit does not include changes in romstage/bootblock to enable
suspend/resume feature. Simply adding functions to handle suspend/resume.
Verified by successfully building and booting Google/Snow firmware image.
Change-Id: I17a256afb99f2f8b5e0eac3393cdf6959b239341
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/3129
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
To support suspend/resume, PHY control must be reset only on normal boot
path. So add a new param "mem_reset" to specify that.
Verified to boot successfully on Google/Snow.
Change-Id: Id49bc6c6239cf71a67ba091092dd3ebf18e83e33
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/3128
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
It seems that ConnectorTypeDP in DdiList supports both DP and HDMI monitors.
I tested by DP monitor and HDMI monitor connected by passive DP->HDMI adapter.
Video and audio are OK. Hot plugging is also supported.
This commit partially reverts commit >AMD Thatcher: Fix PCIE link issues< (7f23aeb0) [1].
[1] http://review.coreboot.org/3011
Change-Id: I23cf1c69a8274f47daf56f1a12aafd88bad4a128
Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com>
Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/3088
Tested-by: build bot (Jenkins)
Reviewed-by: Bruce Griffith <Bruce.Griffith@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This adds support for display bring-up on Snow. It
includes framebuffer initialization and LCD enable functions.
Change-Id: I16e711c97e9d02c916824f621e2313297448732b
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3116
Tested-by: build bot (Jenkins)
Due to
$ more src/southbridge/amd/cimx/sb800/Makefile.inc
[…]
romstage-y += cfg.c
romstage-y += early.c
romstage-y += smbus.c
ramstage-y += cfg.c
ramstage-y += late.c
[…]
`src/southbridge/amd/cimx/sb800/` is passed with the switch `-I` to
the compiler, where it is also going to find the header file
`sb_cimx.h`. Therefore use `#include <sb_cimx>` everywhere, which is
what some AMD SB800 based boards already do.
The only effect is, that the compiler will not needlessly look into
directories which do not contain the header file [1].
The following command was used for the replacement.
$ git grep -l sb_cimx.h src/mainboard/ | xargs sed -i 's/#include "sb_cimx.h"/#include <sb_cimx.h>/'
[1] http://gcc.gnu.org/onlinedocs/cpp/Search-Path.html
Change-Id: I96ab34bac1524e6c38c85dfe9d99cb6ef55e6d7c
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3118
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This PLL is unused and can be disabled to save about 250mW.
Change-Id: I1be37304d6ea5ff78696e05ad1023ce3c57f636c
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3109
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This just cleans up a few areas:
- Removed an unnecessary delay from exynos_dp_bridge_setup()
- The delay at the end of exynos_dp_bridge_init() is necessary, so
removed the comment suggesting that it might not be.
- Simplified exynos_dp_hotplug
Change-Id: I44150f5ef3958e333985440c1022b4f1544a93aa
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3113
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This enables clock gating to save power on unused IPs.
Change-Id: I9ab2a2535ebb91bb4110390a6f055a67146bdbf9
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3110
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This patch is based on >>AMD Thatcher: ConnectorTypeDP supports both DP and HDMI<< (I23cf1c6) [1]
I tested by DP monitor and HDMI monitor connected by passive DP->HDMI adapter.
Video and audio are OK. Hot plugging is also supported.
[1] http://review.coreboot.org/#/c/3088/
Change-Id: I291beff43609ecb68ece24939f2dbc7c08dd0374
Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com>
Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/3090
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This enables the thermal management unit (TMU) on Snow.
Change-Id: Idd76af40bf0a5408baf61ef2665fd52ae4e260ba
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3108
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
Same splitting as done on Persimmon and ASRock.
Moving common DSDT code to common areas and adding
new files as necessary. Boards updated are:
Inagua
Union-Station
South-Station
Change-Id: I8c9eea62996b41cea23a9c16858c4249197f6216
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/3051
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
1) The macros GNB_GPP_PORTx_PORT_PRESENT, GNB_GPP_PORTx_SPEED_MODE,
GNB_GPP_PORTx_LINK_ASPM and GNB_GPP_PORTx_CHANNEL_TYPE are not used.
This is based on >AMD Thatcher: remove unused macros in PlatformGnbPcieComplex.h< [1].
2) Disable unused PCIE port in devicetree.cb.
PCIE port 3 is not used in Parmer.
This is based on item 3 of >AMD Thatcher: Fix PCIE link issues< [2].
[1] http://review.coreboot.org/#/c/3087/
[2] http://review.coreboot.org/#/c/3011/
Change-Id: Id6f00d5e77ce5133d9ef3db07f95ad03a59e061a
Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com>
Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/3099
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This function isn't yet used for much, or perhaps anything, but where it
appears in the code it's ored with other values. Since we're not actually
retrieving anything, it might be best to return 0 so that the other values
that are being ored in can be expressed and this function can stay dormant
until it actually has something to do.
Change-Id: I6edc222a5c2d00ece2ecfad5191a615331eeaf16
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3098
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
We need to read it to report its value to the payload. The kernel will
reconfigure it as an external interrupt, but we'll make it a regular input
for now.
Change-Id: I019bd2c2731144d3b7bb53fad0c2c903874f616c
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3096
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
These names were inherited from chromeos.c where they've already been
fixed.
Change-Id: I7ad57b979b7b8f42f6bd68d1ecf887caba3fa3f1
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3095
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Tested-by: build bot (Jenkins)
ARM doesn't use option ROMs, so this value doesn't make sense.
Change-Id: I1a0f0854e1dd4b9594ca0c147e590337520436da
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3094
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Tested-by: build bot (Jenkins)
Got rid of a lot of #defines, some of which were converted to enums and
the rest which were eliminated entirely. Got rid of cruft in
get_developer_mode_switch and started using it for the dev mode GPIO.
Instead of a macro defining how many GPIOs are expected, now the code
actually counts the GPIOs as they're added.
Change-Id: I97b6b9f52a72d1276eb3cf36d7f9dd7b335b4d19
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3093
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Tested-by: build bot (Jenkins)
Implement the get_recovery_mode_switch function using the newly added I2C
based Chrome EC support.
Change-Id: I9d0200629887f202edf017cba3222a7d7f5b053e
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3092
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Tested-by: build bot (Jenkins)
The comment about the lid switch was left over from when this file was copied
from another board and was incorrect. Also fixed a capitalization
inconsistency.
Change-Id: Icefd19047971e13c08f615578e4a181e82a2997f
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3091
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Tested-by: build bot (Jenkins)
The code has been taken from the google link mainboard
and modified to fit the ThinkPad X60.
Change-Id: Ie16e45163acdc651ea46699ecc33055bfd34099c
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Reviewed-on: http://review.coreboot.org/2998
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Google's Chrome EC can be installed on LPC or I2C bus, using different command
protocol. This commit adds I2C support for devices like Google/Snow.
Note: I2C interface cannot be automatically probed so the bus and chip number
must be explicitly set.
Verified by booting Google/Snow, with following console output:
Google Chrome EC: Hello got back 11223344 status (0)
Google Chrome EC: version:
ro: snow_v1.3.108-30f8374
rw: snow_v1.3.128-e35f60e
running image: 1
Change-Id: I8023eb96cf477755d277fd7991bdb7d9392f10f7
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/3074
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
These are not defined since commit »Drop HAVE_MAINBOARD_RESOURCES«
(1c5071d1) [1] but were unfortunately introduced again in new ports.
[1] http://review.coreboot.org/1414
Change-Id: I5eb61628141aefd08779615702d51ca155fa632a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/2707
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This removes the wait_ms argument from the dp_controller_init(). The
only delay involved is a constant 60ms delay that happens if
everything else goes well. This delay is derived from the LCD spec
so there's no reason it should be baked into the controller code.
(This patch also has the side-effect of fixing a bug where we were
delaying on an undefined value for wait_ms).
Change-Id: I03aa19f2ac2f720524fcb7c795e10cc57f0a226e
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3078
Reviewed-by: Gabe Black <gabeblack@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Add a microsecond timer, its declaration, the function to start it,
and its usage. To start it, one calls timer_start(). From that point
on, one can call timer_us() to find microseconds since the timer was
started.
We show its use in the bootblock. You want it started very early.
Finally, the delay.h change having been (ironically) delayed, we
create time.h and have it hold one declaration, for the timer_us() and
timer_start() prototype.
We feel that these two functions should become the hardware specific
functions, allowing us to finally move udelay() into src/lib where it
belongs.
Change-Id: I19cbc2bb0089a3de88cfb94276266af38b9363c5
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/3073
Tested-by: build bot (Jenkins)
This reverts commit 1fde22c54cacb15493bbde8835ec9e20f1d39bf5:
commit 1fde22c54c
Author: Patrick Georgi <patrick.georgi@secunet.com>
Date: Tue Apr 9 15:41:23 2013 +0200
siemens/sitemp_g1p1: Make ACPI report the right mmconf region
ACPI reported the entire space between top-of-memory and some
(relatively) arbitrary limit as useful for MMIO. Unfortunately
the HyperTransport configuration disagreed. Make them match up.
Other boards are not affected since they don't report any region
for that purpose at all (it seems).
Change-Id: I432a679481fd1c271f14ecd6fe74f0b7a15a698e
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/3047
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
It sneaked in without it's dependencies and, therefore, broke the build for
all amdk8 targets. Paul Menzel already commented on the issue in [1]. It
also doesn't look like the dependencies would be pulled soon [2].
[1] http://review.coreboot.org/#/c/3047/
[2] http://review.coreboot.org/#/c/2662/
Change-Id: Ica89563aae4af3f0f35cacfe37fb608782329523
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: http://review.coreboot.org/3063
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
1). Thatcher PCIE x8 slot is reverse order.
Although the PCIE slot is x16, it actually uses 8 lanes(15:8).
Because the PCIE slot is configured by PortList[0], fix this item can enable the slot.
A x1 PCIE network adapter works well in this slot.
2). Fix DdiList to detect DP monitor or HDMI monitor.
GPIO50 can be used to detect DP0/HDMI0 monitor.
If GPIO50 is 1, it is DP monitor. If GPIO50 is 0, it is HDMI monitor.
GPIO51 can be used to detect DP1/HDMI1 in the same way.
3). Disable unused PCIE port and clean up code in PlatformGnbPcie.c and devicetree.cb.
PCIE port 3 and 7 are not used in Thatcher.
Change-Id: I8524b6fc1b6cdc03ba92e7191186bfb0986767c8
Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com>
Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/3011
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Split the Persimmon DSDT into common code areas.
For example, split the Southbridge specific code into
the Southbridge directory and CPU specific code into
the CPU directory. Also adding the superio.asl file
to the Persimmon DSDT tree. This file is empty for
the moment but will be necessary in the future. I have
also emptied the thermal.asl file in the mainboard
directory because it does not seem to perform as
intended (fan control does not change when it is
brought back into the code base) and it has been
inside a '#if 0' statement for a long time. Removing
it until it is decided that it is actually necessary.
This change was verified in three different ways:
1. Visual comparison of the compiled DSDT pulled from the
Persimmon after booting into Linux using the ACPI tools
acpidump, acpixtract, and iasl. The comparison was done
between the DSDT before and after doing the split work.
This test is somewhat difficult considering the expanse
of the changes. Blocks of code have been moved, and
others changed.
2. Linux logs were dumped before and after the DSDT split.
Logs dumped and compared include dmesg and lspci -tv.
Neither log changed significantly between the two compare
points.
3. The test suite FWTS was run on the Coreboot build both
before and after doing the DSDT split with the command
'sudo fwts -b -P -u'. The flag -b specifies all batch jobs,
-P specifies all power tests, and -u specifies utilities.
Interactive jobs were not run as most of them consist of
laptop checks. Again, there were no significant changes
between the two endpoints.
These tests lead me to believe that there was no change in
the functionality of the ACPI tables apart from what is
known and expected.
This patch is the first of a series of patches to split the DSDT.
The ASRock patch was merged before this one and breaks the ASROCK
E350M1 build (patch 8d80a3fb: http://review.coreboot.org/#/c/3050/).
Please be aware of this dependency when pulling these patches.
Other patches that depend on this patch are
'AMD Fam14: Split out the AMD Fam14 DSDT'
(http://review.coreboot.org/#/c/3051/)
and 'Fam14 DSDT: Also return for unrecognized UUID in _OSC'
(http://review.coreboot.org/#/c/3052/)
Change-Id: I53ff59909cceb30a08e8eab3d59b30b97c802726
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/3048
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
We need these to be inputs so they can be read when populating the coreboot
tables. It seems like a good idea to do this early to ensure that the input
gate capacitance has had a chance to charge, and if we decide to use
actually use that information during the ROM stage to do earlier RW
firmware selection.
It is not guarded by a ChromeOS config variable because those lines are
always intended to be input GPIOs, regardless of whether we're running
ChromeOS or not.
Change-Id: Id76008931b5081253737c6676980a1bdb476ac09
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/3067
Tested-by: build bot (Jenkins)
This is the same split as was done on the Persimmon.
Change-Id: I25bd63f23417b7926232f07eaaa7917170af9d60
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/3050
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
ACPI reported the entire space between top-of-memory and some
(relatively) arbitrary limit as useful for MMIO. Unfortunately
the HyperTransport configuration disagreed. Make them match up.
Other boards are not affected since they don't report any region
for that purpose at all (it seems).
Change-Id: I432a679481fd1c271f14ecd6fe74f0b7a15a698e
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/3047
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Add basic edp support to the ramstage. Not working.
Change-Id: I15086e03417edca7426c214e67b51719d8ed9341
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/3055
Tested-by: build bot (Jenkins)
This is a simpler device tree that is also more correct,
and has graphics settings as well.
Change-Id: I342d8be7dddb76e6992876c73f5c625c926977d3
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/3053
Tested-by: build bot (Jenkins)
This re-factors the Exynos5 I2C code to be simpler and use the
new API, and updates users accordingly.
- i2c_read() and i2c_write() functions updated to take bus number
as an argument.
- Get rid of the EEPROM_ADDR_OVERFLOW stuff in i2c_read() and
i2c_write(). If a chip needs special handling we should take care
of it elsewhere, not in every low-level i2c driver.
- All the confusing bus config functions eliminated. No more
i2c_set_early_config() or i2c_set_bus() or i2c_get_bus(). All this
is handled automatically when the caller does a transaction and
specifies the desired bus number.
- i2c_probe() eliminated. We're not a command-line utility.
- Let the compiler place static variables automatically. We don't need
any of this fancy manual data placement.
- Remove dead code while we're at it. This stuff was ported early on
and much of it was left commented out in case we needed it. Some
also includes nested macros which caused gcc to complain.
- Clean up #includes (no more common.h, woohoo!), replace debug() with
printk().
Change-Id: I8e1f974ea4c6c7db9f33b77bbc4fb16008ed0d2a
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3044
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The existing header was imported along with the Exynos code and left
mostly unchanged. This is the first patch in a series intended to
replace the imported u-boot I2C API with a much simpler and cleaner
interface:
- We only need to expose i2c_read() and i2c_write() in our public API.
Everything else is board/chip-dependent and should remain hidden
away.
- i2c_read and i2c_write functions will take bus number as an arg
and we'll eliminate i2c_get_bus and i2c_set_bus. Those are prone to
error and end up cluttering the code since the user needs to save
the old bus number, set the new one, do the read/write, and restore
the old value (3 added steps to do a simple transaction).
- Stop setting default values for board-specific things like SPD
and RTC bus numbers (as if we always have an SPD or RTC on I2C).
- Death to all the trivial inline wrappers. And in case there was any
doubt, we really don't care about the MPC8xx. Though if we did then
we would not pollute the public API with its idiosyncrasies.
Change-Id: I4410a3c82ed5a6b2e80e3d8c0163464a9ca7c3b0
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3043
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Originally developed by LiPPERT and after the acquisition marketed as
'LiPPERT by ADLINK', the plan is now to streamline both boards into the
ADLINK naming scheme. But AFAIK a few have already been sold and as of
this writing the website still advertises the old names. And in any case
the veteran LX products will continue to be sold by ADLINK under their
original names.
So create CONFIG_VENDOR_ADLINK, currently only telling users to look under
LiPPERT (however any future boards will be added here).
Further add an explanation to CONFIG_VENDOR_LIPPERT, and in the Mainboard
model selection show both names.
Change-Id: Iaafa88533ef4cce33243293c3d55754e7e93d003
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-on: http://review.coreboot.org/3046
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This moves highly board-specific code out from the Exynos5250
power_init() into Snow's romstage.c. There's no reason the CPU-
specific code should care about which PMIC we are using and
which bus it is on.
Change-Id: I52313177395519cddcab11225fc23d5e50c4c4e3
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/3034
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This was a first pass at display port support, we have
realized that it was ultimately a bad path. The display
hardware is intimately tied into a specific cpu and
mainboard combination, and the code has to be elsewhere.
The devicetree formatting is ugly, but it matters not:
it's changing soon.
Change-Id: Iddce54f9e7219a7569315565fac65afbbe0edd29
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/3029
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Commit 5d741567 added a prototype to broadcom.c to fix a warning. This part
is fine.
It also changed mainboard.c to #include broadcom.c. But broadcom.c is
already in Makefile.inc, now building will fail because the linker gets
broadcom_init() twice.
Undo the change to mainboard.c but keep the change to broadcom.c.
Change-Id: Ieccc098f477ffacccf4174056998034a220a9744
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-on: http://review.coreboot.org/3012
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Now that the ASRock E350M1 builds without any warnings, remove the
config option `WARNINGS_ARE_ERRORS` set to no by default from
the file `Kconfig` so warnings are treated as errors to prevent
code from being added in the future introducing warnings.
Change-Id: Idfecfb1434158969334a4b37972b5fc6fd76e72a
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/3014
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
When building the ASRock E350M1, the following warnings are shown.
$ make # on Jenkins (build server)
[…]
CC mainboard/asrock/e350m1/buildOpts.romstage.o
In file included from src/mainboard/asrock/e350m1/buildOpts.c:294:0:
src/vendorcode/amd/agesa/f14/Include/PlatformInstall.h:2071:6: warning: "DDR1333_FREQUENCY" is not defined [-Wundef]
src/vendorcode/amd/agesa/f14/Include/PlatformInstall.h:2071:40: warning: "DDR1866_FREQUENCY" is not defined [-Wundef]
src/vendorcode/amd/agesa/f14/Include/PlatformInstall.h:2089:5: warning: "TIMING_MODE_AUTO" is not defined [-Wundef]
src/vendorcode/amd/agesa/f14/Include/PlatformInstall.h:2089:31: warning: "TIMING_MODE_SPECIFIC" is not defined [-Wundef]
src/vendorcode/amd/agesa/f14/Include/PlatformInstall.h:2113:5: warning: "QUADRANK_UNBUFFERED" is not defined [-Wundef]
src/vendorcode/amd/agesa/f14/Include/PlatformInstall.h:2113:33: warning: "QUADRANK_UNBUFFERED" is not defined [-Wundef]
src/vendorcode/amd/agesa/f14/Include/PlatformInstall.h:2127:5: warning: "POWER_DOWN_BY_CHIP_SELECT" is not defined [-Wundef]
src/vendorcode/amd/agesa/f14/Include/PlatformInstall.h:2127:28: warning: "POWER_DOWN_BY_CHIP_SELECT" is not defined [-Wundef]
[…]
Adding the corresponding defines as done for AMD Persimmon in
commit d7a696d0f2
Author: efdesign98 <efdesign98@gmail.com>
Date: Thu Sep 15 15:24:26 2011 -0600
Persimmon updates for AMD F14 rev C0
Reviewed-on: http://review.coreboot.org/137
addresses the warnings.
Change-Id: Id311b2dacdba5f2e6b4d834e43db0310213a35f9
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2962
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
The ACPI NVS region was setup in place and there was a CBMEM
table that pointed to it. In order to be able to use NVS
earlier the CBMEM region is allocated for NVS itself during
the LPC device init and the ACPI tables point to it in CBMEM.
The current cbmem region is renamed to ACPI_GNVS_PTR to
indicate that it is really a pointer to the GNVS and does
not actually contain the GNVS.
Change-Id: I31ace432411c7f825d86ca75c63dd79cd658e891
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2970
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This enables all of the SerialIO devices and sets the flag
to put them in ACPI mode.
Change-Id: I7436c47d26028e95bbefafc320854c7cc34a4d44
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2972
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
When building the ASRock E350M1, the following warning is shown.
$ make # on Jenkins (build server)
[…]
CC mainboard/asrock/e350m1/mptable.ramstage.o
src/mainboard/asrock/e350m1/mptable.c:64:12: warning: unused variable 'dev' [-Wunused-variable]
[…]
Removing the variable `dev` addresses the warning.
The same change was done in the following commit for the
AMD Persimmon board.
commit d7a696d0f2
Author: efdesign98 <efdesign98@gmail.com>
Date: Thu Sep 15 15:24:26 2011 -0600
Persimmon updates for AMD F14 rev C0
Reviewed-on: http://review.coreboot.org/137
Change-Id: I83f4630cb6ab1e4c95d04b4e8423850ed1858e45
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2965
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
When building the ASRock E350M1, the following warning is shown.
$ make # on Jenkins (build server)
[…]
CC mainboard/asrock/e350m1/mptable.ramstage.o
src/mainboard/asrock/e350m1/mptable.c: In function 'smp_write_config_table':
src/mainboard/asrock/e350m1/mptable.c:58:3: warning: implicit declaration of function 'get_bus_conf' [-Wimplicit-function-declaration]
[…]
Including the header file `cpu/amd/amdfam14.h` declaring the
function addresses this warning.
The same change was done in the following commit for the
AMD Persimmon board.
commit d7a696d0f2
Author: efdesign98 <efdesign98@gmail.com>
Date: Thu Sep 15 15:24:26 2011 -0600
Persimmon updates for AMD F14 rev C0
Reviewed-on: http://review.coreboot.org/137
Change-Id: I7912571fa57f6512b10fc9b5845427fcb6eb50c0
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2966
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
When building the ASRock E350M1, the following warning is shown.
$ make # on Jenkins (build server)
[…]
CC mainboard/asrock/e350m1/mainboard.ramstage.o
src/mainboard/asrock/e350m1/mainboard.c: In function 'mainboard_enable':
src/mainboard/asrock/e350m1/mainboard.c:63:2: warning: implicit declaration of function 'pm_iowrite' [-Wimplicit-function-declaration]
[…]
This warning was introduced by moving the initialization of the
ASF registers using `pm_iowrite` to `mainboard.c` in
commit db6c5bfd8b
Author: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Date: Thu Mar 21 22:21:28 2013 +0100
Asrock E350M1: Use SPD read code from F14 wrapper
Reviewed-on: http://review.coreboot.org/2875
and is fixed by including `southbridge/amd/cimx/cimx_util.h`
declaring `pm_iowrite`.
Note, that the other AMD SB800 based boards seem to use the
header file `southbridge/amd/sb800/sb800.h`, so no warning is shown
for those. But since the CIMx SB800 code is used, the routines
from the CIMx directory are more appropriate to declare these functions.
So delete the commented out include line for this header too.
Change-Id: I179aad5157c5a91294339a3e7b6c4c1715c6f099
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2957
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This enables the TPM device in ACPI tables so the OS is able
to probe for the TPM without needing it be force loaded.
Change-Id: I21e660ac1c12e3e1341cf266cf8f0bf03763df5a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2968
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
There is a wildcard rule to include mainboard/fadt.c.
Change-Id: I7f59d6b241c683b62c2c41c5795e45184882635e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/2940
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Unfortunately, an unneeded mainboard specific `pmio.h` was created
when merging the AMD Parmer and Thatcher ports.
Rudolf used the header from a more generic location
southbridge/amd/agesa/hudson/hudson.h
doing the the ASUS F2A85-M port, but did not delete the `pmio.h`
now unused `pmio.h` header file.
So adapt AMD Parmer and Thatcher to use the Hudson one as done for
the ASUS F2A85-M and delete the now unused mainboard specific header
file `pmio.h` to avoid duplication.
Change-Id: I961cd145ebc3b83e31c638ac453ac95ee19c18db
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2958
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
When building the ASRock E350M1, the following warning is shown.
$ make # on Jenkins (build server)
[…]
CC mainboard/asrock/e350m1/irq_tables.ramstage.o
src/mainboard/asrock/e350m1/irq_tables.c: In function 'write_pirq_routing_table':
src/mainboard/asrock/e350m1/irq_tables.c:64:2: warning: implicit declaration of function 'get_bus_conf' [-Wimplicit-function-declaration]
[…]
Including the header file `cpu/amd/amdfam14.h` declaring the
function addresses this warning.
The same change was done in the following commit for the
AMD Persimmon board.
commit d7a696d0f2
Author: efdesign98 <efdesign98@gmail.com>
Date: Thu Sep 15 15:24:26 2011 -0600
Persimmon updates for AMD F14 rev C0
Reviewed-on: http://review.coreboot.org/137
Change-Id: I40b5735feb7116961ca0c4d6940ec55cdf42d3c6
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2956
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
When building the ASRock E350M1, the following warning is shown.
$ make # on Jenkins (build server)
[…]
CC mainboard/asrock/e350m1/get_bus_conf.ramstage.o
src/mainboard/asrock/e350m1/get_bus_conf.c: In function 'get_bus_conf':
src/mainboard/asrock/e350m1/get_bus_conf.c:82:3: warning: implicit declaration of function 'agesawrapper_amdinitlate' [-Wimplicit-function-declaration]
[…]
Including the header file `agesawrapper.h` declaring the function
`agesawrapper_amdinitlate` fixes this warning.
All AMD Family 14 based boards already include that header file. For
example for the board AMD Persimmon the following patch fixed this
warning.
commit d7a696d0f2
Author: efdesign98 <efdesign98@gmail.com>
Date: Thu Sep 15 15:24:26 2011 -0600
Persimmon updates for AMD F14 rev C0
Reviewed-on: http://review.coreboot.org/137
Change-Id: I695420b7071e07cb7d4667b2479b9a26ea13723d
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2955
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
When building the ASRock E350M1, the following warning is shown.
$ make # on Jenkins (build server)
[…]
CC mainboard/asrock/e350m1/PlatformGnbPcie.romstage.o
CC mainboard/asrock/e350m1/agesawrapper.romstage.o
CC mainboard/asrock/e350m1/buildOpts.romstage.o
src/mainboard/asrock/e350m1/PlatformGnbPcie.c: In function 'OemCustomizeInitEarly':
src/mainboard/asrock/e350m1/PlatformGnbPcie.c:131:5: warning: 'return' with a value, in function returning void [enabled by default]
[…]
The function signature is (the return type might not be part of this though [1]),
VOID
OemCustomizeInitEarly (
IN OUT AMD_EARLY_PARAMS *InitEarly
)
so do not return anything.
All other AMD Family 14 boards already have the correct code. For example
following commit fixed this for AMD Persimmon.
commit d7a696d0f2
Author: efdesign98 <efdesign98@gmail.com>
Date: Thu Sep 15 15:24:26 2011 -0600
Persimmon updates for AMD F14 rev C0
Reviewed-on: http://review.coreboot.org/137
[1] http://cboard.cprogramming.com/cplusplus-programming/117286-what-exactly-function-signature.html
Change-Id: Ie60246bd9bb8452efd096e6838d8610f6364a6aa
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2954
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
This adds a call to explicitly configure L2 cache (though defaults
should be set correctly).
Change-Id: I120e29c986918c2904a0332e46fcf9f1c5380d85
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2950
Reviewed-by: Gabe Black <gabe.black@gmail.com>
Tested-by: build bot (Jenkins)
The WTM2 board has a fairly static configuration. As such
it's been tested to properly handle CACHE_ROM given the number
of MTRRs the boards' CPUs supports.
Change-Id: Ic67cd1eebce580003dc6b6655cac2b2a92dd1b5f
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2964
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Now that the AMD Inagua builds without any warnigs, remove the
config option `WARNINGS_ARE_ERRORS` set to no by default from
the file `Kconfig` so warnings are treated as errors to prevent
code from being added in the future introducing warnings.
Change-Id: I0b58bd74b06dc54d180b16d6a207354b5fea0d0f
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2953
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Building the AMD Inagua board, the following warning is thrown.
CC mainboard/amd/inagua/get_bus_conf.ramstage.o
src/mainboard/amd/inagua/broadcom.c:319:6: warning: no previous prototype for 'broadcom_init' [-Wmissing-prototypes]
This warning was introduced by commit 3926b4c5.
commit 3926b4c520
Author: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Date: Fri Mar 1 19:41:41 2013 +0100
AMD Inagua: add GEC firmware, document Broadcom BCM57xx Selfboot Patch format
Reviewed-on: http://review.coreboot.org/2831
Adding the prototype to `broadcom.c` and removing it from
`mainboard.c` fixes the warning.
Change-Id: I1da0c4e972e129047dd8230d573f1c43fd71eb20
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2952
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Automatically select CACHE_ROM for all Google boards.
Tested by generating a config for the link board. CACHE_ROM
was selected and was unable to unselect it using
'make oldconfig'.
Change-Id: I8e34207e3929a020bb0280657f95ba7a000ad024
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2963
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This reverts commit 9427ca151e
Looks like we were a bit too anxious to see this one get in. The devicetree.cb change seems to have broken things.
coreboot memory table:
0. 0000000050000000-000000005000ffff: RESERVED
1. 00000000bff00000-00000000bfffffff: CONFIGURATION TABLES
2. 0000014004000000-00000140044007ff: RESERVED
Before this patch:
coreboot memory table:
0. 0000000040000000-00000000bfefffff: RAM
1. 00000000bff00000-00000000bfffffff: CONFIGURATION TABLES
Change-Id: I618e4f1976265d56cfd6a61d0c5736c55a0f3cec
Reviewed-on: http://review.coreboot.org/2914
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
This does NOT turn on the graphics.
The device tree has been changed enough so that, at the very least, the correct
functions are called at the correct time, with the correct paramaters. We
decided to yank the I2C entries as they did not obvious function and might
not even have been correct.
Not working, seemingly, but we need to add a 4M resource for
memory, and it seems it needs to be fixed at the address shown.
This address was chosen from current hardware.
We realized that the display code should be part of the cpu -- that's how
the hardware works!
Change-Id: Ied65a554f833566be817540702f79a02e7b6cb6e
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2615
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
This adds new MMU setup code. Most notably, this version uses
cbmem_add() to determine the translation table base address, which
in turn is necessary to ensure payloads which wipe memory can tell
which regions to wipe out.
TODOs:
- Finish cleaning up references to old cache/MMU stuff
- Add L2 setup (from exynos_cache.c)
- Set up ranges dynamically rather than in ramstage's main().
Change-Id: Iba5295a801e8058a3694e4ec5b94bbe9a69d3ee6
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2877
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The Broadcom BCM5785 GbE MAC integrated in the AMD Hudson-E1 requires a
secret sauce firmware blob to work. As Broadcom wasn't willing to send us
any documentation (or a firmware adapted to our Micrel PHY) I had to figure
out everything by myself in many weeks of hard detective work.
In the end we had to settle for a different solution, the modified firmware
I devised for the Micrel KSZ9021 PHY on our early FrontRunner-AF prototypes
is no longer needed for the production version. However the information
contained here might be very useful for others who'd like to use a
competing PHY instead of Broadcom's 50610, so it should not get lost.
And of course the unmodified, but now in large parts documented Selfboot
Patch is needed to get Ethernet on AMD Inagua. The code introduced here
should make the Hudson's internal MAC usable without having to add the
proprietary firmware blob. - At least in theory.
Unfortunately we've been unable to actually test this patch on Inagua,
therefore the broadcom_init() call in mainboard.c was left commented out.
If you have the hardware and can confirm it works please enable it.
The fun thing is: as Broadcom refused to do any business with us at all,
or send us any documentation, we never had to sign an NDA with them. This
leaves me free to publish everything I have found out. :-)
Change-Id: I94868250591862b376049c76bd21cb7e85f82569
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-on: http://review.coreboot.org/2831
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The patch is based on Thatcher board. So far it boots Linux (3.2/3.7),
internal network adapter works, AHCI works. External PCI/PCIe slots
works too. Power management/ACPI seems to work.
Internal VGA works with dumped ROM (VGA/DVI), but lacks GART.
PCI pref devices are being relocated by Linux, reason unknown.
This is a good start.
USB and XHCI untested but visible.
Change-Id: I1869aecb2634d548b00b3c9139517d6a0e0c9817
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Reviewed-on: http://review.coreboot.org/2038
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
Changes:
- Get rid of the E350M1 mainboard specific code and use the
platform generic function wrapper that was added in change
http://review.coreboot.org/#/c/2497/
AMD f14: Add SPD read functions to wrapper code
- Move DIMM addresses into devicetree.cb
- Add the ASF init that used to be in the SPD read code into
mainboard_enable()
Notes:
- The DIMM reads only happen in romstage, so the function is not
available in ramstage. Point the read-SPD callback to a generic
function in ramstage.
Change-Id: I08c2aebc62facc14f94400ee1ad188901ba73f19
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-on: http://review.coreboot.org/2875
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Changes:
- Get rid of the LiPPERT FrontRunner-AF and Toucan-AF mainboard
specific code and use the platform generic function wrapper that
was added in change
http://review.coreboot.org/#/c/2497/
AMD f14: Add SPD read functions to wrapper code
- Move DIMM addresses into devicetree.cb
- Add the ASF init that used to be in the SPD read code into
mainboard_enable()
Notes:
- The DIMM reads only happen in romstage, so the function is not
available in ramstage. Point the read-SPD callback to a generic
function in ramstage.
Change-Id: I4ee5e1bc34f4caee20615c48248d4f7605c09377
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-on: http://review.coreboot.org/2874
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
coreboot tables are, unlike general system tables, a platform
independent concept. Hence, use the same code for coreboot table
generation on all platforms. lib/coreboot_tables.c is based
on the x86 version of the file, because some important fixes
were missed on the ARMv7 version lately.
Change-Id: Icc38baf609f10536a320d21ac64408bef44bb77d
Signed-off-by: Stefan Reinauer <reinauer@coreboot.org>
Reviewed-on: http://review.coreboot.org/2863
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@google.com>
Tested-by: build bot (Jenkins)
It's helpful to switch back and forth for developer and
recovery settings while testing boards. The wtm2 board
currently doesn't have gpios which dynamically seelect that.
Might as well make it easy to change the value for each
setting with one define. The original defaults are kept.
Change-Id: I7b928c592fd20a1b847e4733f4cdef09d6ddad4c
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2861
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The get_write_protect_state() function was added to the
chromeos API that needs to be supported by the boards.
Implement this support.
Built and booted. Noted firmware select worked on an image with
RW firmware support. Also checked that recovery mode worked as
well by choosing the RO path.
Change-Id: Ifd213be25304163fc61d153feac4f5a875a40902
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2855
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Convert the existing haswell code to support reloctable ramstage
to use dynamic cbmem. This patch always selects DYNAMIC_CBMEM as
this option is a hard requirement for relocatable ramstage.
Aside from converting a few new API calls, a cbmem_top()
implementation is added which is defined to be at the begining of the
TSEG region. Also, use the dynamic cbmem library for allocating a
stack in ram for romstage after CAR is torn down.
Utilizing dynamic cbmem does mean that the cmem field in the gnvs
chromeos acpi table is now 0. Also, the memconsole driver in the kernel
won't be able to find the memconsole because the cbmem structure
changed.
Change-Id: I7cf98d15b97ad82abacfb36ec37b004ce4605c38
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2850
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Here's the great news: From now on you don't have to worry about
hitting the right io.h include anymore. Just forget about romcc_io.h
and use io.h instead. This cleanup has a number of advantages, like
you don't have to guard device/ includes for SMM and pre RAM
anymore. This allows to get rid of a number of ifdefs and will
generally make the code more readable and understandable.
Potentially in the future some of the code in the io.h __PRE_RAM__
path should move to device.h or other device/ includes instead,
but that's another incremental change.
Change-Id: I356f06110e2e355e9a5b4b08c132591f36fec7d9
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2872
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Force link speed on these platforms to 3 Gbps to defeat buggy SATA
drives.
Change-Id: Ia38a7c486fb1f4469cd67ca5244bbf61f877d556
Signed-off-by: Shawn Nematbakhsh <shawnn@google.com>
Reviewed-on: http://review.coreboot.org/2823
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This makes use of the new functions from pmutil.c that take
care of the differences between -H and -LP chipsets.
It also adds support for the LynxPoint-LP GPE0 register block
and the SMI/SCI routing differences.
The FADT is updated to report the new 256 byte GPE0 block on
wtm2/wtm2 boards which is too big for the 64bit X_GPE0 address
block so that part is zeroed to prevent IASL and the kernel
from complaining about a mismatch.
This was tested on WTM2. Unfortunately I am still unable to get an
SCI delivered from the EC but I suspect that is due to a magic
command needed to put the EC in ACPI mode. Instead I verified that
all of the power management and GPIO registers were set to expected
values.
I also tested transitions into S3 and S5 from both the kernel and
by pressing the power button at the developer mode screen and they
all function as expected.
Change-Id: Ice9e798ea5144db228349ce90540745c0780b20a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2816
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Changes:
- Get rid of the h8scm mainboard specific code and use the
platform generic function wrapper that was added in change
http://review.coreboot.org/#/c/2777/
AMD Fam15: Add SPD read functions to wrapper code
- Move DIMM addresses into devicetree.cb
Notes:
- The DIMM reads only happen in romstage, so the function is not
available in ramstage. Point the read-SPD callback to a generic
function in ramstage.
Change-Id: I575221039ad65a59ae0f93397ef1038b669e81c7
Signed-off-by: Kimarie Hoot <kimarie.hoot@se-eng.com>
Reviewed-on: http://review.coreboot.org/2829
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Changes:
- Get rid of the dinar mainboard specific code and use the
platform generic function wrapper that was added in change
http://review.coreboot.org/#/c/2777/
AMD Fam15: Add SPD read functions to wrapper code
- Move DIMM addresses into devicetree.cb
Notes:
- The DIMM reads only happen in romstage, so the function is not
available in ramstage. Point the read-SPD callback to a generic
function in ramstage.
- select_socket() and restore_socket() were created from code that
was removed from AmdMemoryReadSPD() in dimmSpd.c. The functionality
is specific to the dinar mainboard configuration and was therefore
split from the generic read SPD functionality.
Change-Id: I1e4b9a20dc497c15dbde6d89865bd5ee7501cdc0
Signed-off-by: Kimarie Hoot <kimarie.hoot@se-eng.com>
Reviewed-on: http://review.coreboot.org/2830
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Changes:
- Get rid of the s8226 mainboard specific code and use the
platform generic function wrapper that was added in change
http://review.coreboot.org/#/c/2777/
AMD Fam15: Add SPD read functions to wrapper code
- Move DIMM addresses into devicetree.cb
Notes:
- The DIMM reads only happen in romstage, so the function is not
available in ramstage. Point the read-SPD callback to a generic
function in ramstage.
- select_socket() and restore_socket() started by duplicating
sp5100_set_gpio() and sp5100_restore_gpio(), which were in
dimmSpd.c. In addition to renaming the functions to more
specifically state their purpose, some cleanup and magic number
reduction was done.
Change-Id: I1eaf64986ef4fa3f89aed2b69d3f9c8c913f726f
Signed-off-by: Kimarie Hoot <kimarie.hoot@se-eng.com>
Reviewed-on: http://review.coreboot.org/2827
Tested-by: build bot (Jenkins)
Reviewed-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Changes:
- Get rid of the h8qgi mainboard specific code and use the
platform generic function wrapper that was added in change
http://review.coreboot.org/#/c/2777/
AMD Fam15: Add SPD read functions to wrapper code
- Move DIMM addresses into devicetree.cb
Notes:
- The DIMM reads only happen in romstage, so the function is not
available in ramstage. Point the read-SPD callback to a generic
function in ramstage.
- select_socket() and restore_socket() started by duplicating
sp5100_set_gpio() and sp5100_restore_gpio(), which were in
dimmSpd.c. In addition to renaming the functions to more
specifically state their purpose, some cleanup and magic number
reduction was done.
Change-Id: I346ebd8399d4ba3e280576e667fdc62fa75a63b8
Signed-off-by: Kimarie Hoot <kimarie.hoot@se-eng.com>
Reviewed-on: http://review.coreboot.org/2828
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This code is taken from an EDID reader written at Red Hat.
The key function is
int decode_edid(unsigned char *edid, int size, struct edid *out)
Which takes a pointer to an EDID blob, and a size, and decodes it into
a machine-independent format in out, which may be used for driving
chipsets. The EDID blob might come for IO, or a compiled-in EDID
BLOB, or CBFS.
Also included are the changes needed to use the EDID code on Link.
Change-Id: I66b275b8ed28fd77cfa5978bdec1eeef9e9425f1
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2837
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This is a new state machine. It is more programmatic, in the
case of auxio, and has much more symbolic naming, and very few
"magic" numbers, except in the case of undocumented settings.
As before, the 'pre-computed' IO ops are encoded in the iodefs
table. A function, run, is passed and index into the table and
runs the ops.
A new operator, I, has been added. When the I operator is hit,
run() returns the index of the next operator in the table.
The i915lightup function runs the table. All the AUX channel ops
have been removed from the table, however, and are now called as
functions, using the previously committed auxio function.
The iodefs table has been grouped into blocks of ops, which end in
an I operator. As the lightup function progresses through startup,
and the run() returns, the lightup function performs aux channel
operations.
This code is symbolic enough, I hope, that it will make haswell
graphics bringup simpler.
i915io.c, and the core of the code in i915lightup.c, were
programatically generated, starting with IO logs from the DRM
startup code in the kernel. It is possible to apply the tools that
do this generation to newer IO logs from the kernel.
Change-Id: I8a8e121dc0d9674f0c6a866343b28e179a1e3d8a
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2836
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Add a new operator, P, for the state machine, meaning
implement a palette fill.
Implement a function (palette) that fills the palette when the
P operator is hit.
This replaces 256 lines in the state machine table with 1.
Change-Id: I67d9219fe7de0ecf1fb9faf92130c00c9f5f8e88
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Reviewed-on: http://review.coreboot.org/2835
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
For full integration of FUI into coreboot, we need aux channel
communcations. The intel_dp.c is a file taken from Linux and is
used for aux channel comms. This file has been cut down to work
with coreboot. For now it is associated with the link mainboard
until we get a better handle on how this all fits together. This
code is almost certainly usable on other platforms in the long term.
But one step at a time.
Change-Id: I7be4c56e0a7903f3901ac86e12b28f3bdc0f7947
Signed-off-by: Ronald G. Minnich <rminnich@google.com>
Reviewed-on: http://review.coreboot.org/2834
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This adds a new API for cache maintenance operations. The idea is
to be more explicit about operations that are going on so it's easier
to manage branch predictor, cache, and TLB cleans and invalidations.
Also, this adds some operations that were missing but required early
on, such as branch predictor invalidation. Instruction and sync
barriers were wrong earlier as well since the imported API assumed
we compield with -march=armv5 (which we don't) and was missing
wrappers for the native ARMv7 ISB/DSB/DMB instructions.
For now, this is a start and it gives us something we can easily use
in libpayload for doing things like cleaning and invalidating dcache
when doing DMA transfers.
TODO:
- Set cache policy explicitly before re-enabling. Right now it's left
at default.
- Finish deprecating old cache maintenance API.
- We do an extra icache/dcache flush when going from bootblock to
romstage.
Change-Id: I7390981190e3213f4e1431f8e56746545c5cc7c9
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2729
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This fixes a trivial error with the recovery mode GPIO index.
Change-Id: I7290c1e23cdddaf91c9021d4e4252c0c772b6eab
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2825
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
A fix to eliminate warnings when building romstage files with ChromeOS
compilers
Change-Id: Ia5d7bbdde3aa3439fd493f5795f2cc2bf4c4c187
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2781
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Having this header file in the mainboard directory breaks
the dinar build on cygwin because the header file in the
dinar mainboard is used instead of the correct header file
src/vendorcode/amd/cimx/sb700/OEM.h. The build probably works
fine on Linux systems because, due to case-sensitivity, Oem.h
will not match the #include "OEM.h" statement in
src/southbridge/amd/cimx/sb700/Platform.h.
The Oem.h file in the dinar mainboard is not used by any other
source files, and the defines in the dinar mainboard are duplicated
by defines in the correct OEM.h file. Therefore, the file can be
safely removed.
Change-Id: I81b97eca8116d63644d335edc3bb51f90c7094d9
Signed-off-by: Kimarie Hoot <kimarie.hoot@se-eng.com>
Reviewed-on: http://review.coreboot.org/2776
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
This commit pulls in all the common logic for romstage into
the Haswell cpu directory. The bits specific to the mainboard
still reside under their respective directories. The calling
sequence bounces from the cpu directory to mainboard then back
to the cpu directory. The reasoning is that Haswell systems use
cache-as-ram for backing memory in romstage. The stack is used to
allocate structures. However, now changes can be made to the
romstage for Haswell and apply to all boards.
Change-Id: I2bf08013c46a99235ffe4bde88a935c3378eb341
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2754
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
It was found that the Haswell reference code was smashing through the
stack into the reference code's heap implementation. The reason for this
is because our current CAR allocation is too small. Moreover there are
quite a few things to coordinate between 2 code bases to get correct.
This commit separates the CAR into 2 parts:
1. MRC CAR usage.
2. Coreboot CAR usage.
Pointers from one region can be passed between the 2 modules, but one
should not be able to affect the others as checking has been put into
place in both modules.
The CAR size has effectively been doubled from 0x20000 (128 KiB) to
0x40000 (256KiB). Not all of that increase was needed, but enforcing
a power of 2 size only utilizes 1 MTRR.
Old CAR layout with a single contiguous stack with the region starting
at CONFIG_DCACHE_RAM_BASE:
+---------------------------------------+ Offset CONFIG_DCACHE_RAM_SIZE
| MRC global variables |
| CONFIG_DCACHE_RAM_MRC_VAR_SIZE bytes |
+---------------------------------------+
| ROM stage stack |
| |
| |
+---------------------------------------+
| MRC Heap 30000 bytes |
+---------------------------------------+
| ROM stage console |
| CONFIG_CONSOLE_CAR_BUFFER_SIZE bytes |
+---------------------------------------+
| ROM stage CAR_GLOBAL variables |
+---------------------------------------+ Offset 0
There was some hard coded offsets in the reference code wrapper to start
the heap past the console buffer. Even with this commit the console
can smash into the following region depending on what size
CONFIG_CONSOLE_CAR_BUFFER_SIZE is.
As noted above This change splits the CAR region into 2 parts starting
at CONFIG_DCACHE_RAM_BASE:
+---------------------------------------+
| MRC Region |
| CONFIG_DCACHE_RAM_MRC_VAR_SIZE bytes |
+---------------------------------------+ Offset CONFIG_DCACHE_RAM_SIZE
| ROM stage stack |
| |
| |
+---------------------------------------+
| ROM stage console |
| CONFIG_CONSOLE_CAR_BUFFER_SIZE bytes |
+---------------------------------------+
| ROM stage CAR_GLOBAL variables |
+---------------------------------------+ Offset 0
Another variable was add, CONFIG_DCACHE_RAM_ROMSTAGE_STACK_SIZE,
which represents the expected stack usage for the romstage. A marker
is checked at the base of the stack to determine if either the stack
was smashed or the console encroached on the stack.
Change-Id: Id76f2fe4a5cf1c776c8f0019f406593f68e443a7
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2752
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This is causing a hang in depthcharge. For now just disable
this port.
Change-Id: I87a6db2d8361588e82eee640c74cea690115bed5
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2764
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Rather than have to repeat this bit in every mainboard.
Also, remove the reset of the RTC power status from here.
We had done this in TOT for current platforms but did not
carry it back to emeraldlake2 where this branched from.
If we clear the status here then we don't get an event
logged later which can be important for the devices that
do not have a CMOS battery.
Change-Id: Ia7131e9d9e7cf86228a285df652a96bcabf05260
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2683
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
We're happy to announce coreboot support for the "Stout"
Chromebook, a.k.a Lenovo X131e Chromebook.
Change-Id: I9b995f8d0dd48e41c788b7c3d35b4fac5840e425
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2636
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This is mostly a copy of Whitetip Mountain 1 with specific GPIO
map for this Customer Reference Board (CRB).
This mainboard currently has basic funcionality and is able to
boot a Linux Kernel but many of the new Haswell ULT specific
devices are not yet enabled.
Change-Id: I999452d86f00a2c245fa39b1b76080f6a3b1e352
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2725
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
There was a mix of setup code sprinkled across the various components:
southbridge code in the northbridge, etc. This commit reorganizes the
code so that northbridge code doesn't initialize southbridge components.
Additionally, the calling dram initialization no longer calls out to ME
code. The main() function in the mainboard calls the necessary ME
functions before and after dram initialization.
The biggest change is the addition of an early_pch_init() function
which initializes the BARs, GPIOs, and RCBA configuration. It is also
responsible for reporting back to the caller if the board is being
woken up from S3. The one sequence difference is that the RCBA config
is performed before claling the reference code.
Lastly the rcba configuration was changed to be table driven so that
different board/configurations can use the same code. It should be
possible to have board/configuration specific gpio and rcba
configuration while reusing the romstage code.
Change-Id: I830e41b426261dd686a2701ce054fc39f296dffa
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2681
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Lots of things are still placeholder and need work.
Due to the useful GPIOs being run to either the EC or the SIO1007
I have hard coded developer mode on and recovery mode off.
Change-Id: I4c308bd90db03ac5bffdfde566e5adbbaabac632
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2724
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Adding the 'WordBusNumber' macro to the PCI0
CRES ResourceTemplate in the Persimmon DSDT.
This sets up the bus number for the PCI0 device
and the secondary bus number in the CRS method.
This change came in response to a 'dmesg' error
which states:
'[FIRMWARE BUG]: ACPI: no secondary bus range in _CRS'
By adding the 'WordBusNumber' macro, ACPI can set
up a valid range for the PCIe downstream busses,
thereby relieving the Linux kernel from "guessing"
the valid range based off _BBN or assuming [0-0xFF].
The Linux kernel code that checks this bus range is
in `drivers/acpi/pci_root.c`. PCI busses can have
up to 256 secondary busses connected to them via
a PCI-PCI bridge. However, these busses do not
have to be sequentially numbered, so leaving out a
section of the range (eg. allowing [0-0x7F]) will
unnecessarily restrict the downstream busses.
This is the same change as made to Persimmon with
change-id I44f22:
http://review.coreboot.org/#/c/2592/
Change-Id: I5184df8deb7b5d2e15404d689c16c00493eb01aa
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2736
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
I am removing the _INI method from the AZHD device because
it does not seem to do anything and causes errors in the
FWTS[1] (Firmware Test Suite) test 'method'. The INI
method performs device specific initialization and is
run when OSPM loads a description table. It must only
access OperationRegions that have been indicated as
available by the _REG (Region) method. We do not have a
_REG method and during my testing, I added a REG method
but it did not seem to make a difference in the PCI
register space. The bit fields defined as NSDI (Disable
No Snoop), NSDO (Disable No Snoop Override), and NSEN
(Enable No Snoop Request) do not ever get written from
their default values. And writing to these bit fields
does not seem to be necessary because I did not notice
any change in audio functionality.
In an effort to clean up as many FWTS errors as possible,
I propose removing this method altogether. I have seen no
change in operation (audio works with and without this
method) and there does not seem to be any change in lspci
or dmesg.
FWTS information can be found here:
[1]: https://wiki.ubuntu.com/Kernel/Reference/fwts
This is the same chagne as made to Persimmon in
Change-ID If8d86f:
http://review.coreboot.org/#/c/2726/
Change-Id: Id560ea85a38f73aaba2c35447bbce46bd9c0d0dd
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2741
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
I am removing the _INI method from the AZHD device because
it does not seem to do anything and causes errors in the
FWTS[1] (Firmware Test Suite) test 'method'. The INI
method performs device specific initialization and is
run when OSPM loads a description table. It must only
access OperationRegions that have been indicated as
available by the _REG (Region) method. We do not have a
_REG method and during my testing, I added a REG method
but it did not seem to make a difference in the PCI
register space. The bit fields defined as NSDI (Disable
No Snoop), NSDO (Disable No Snoop Override), and NSEN
(Enable No Snoop Request) do not ever get written from
their default values. And writing to these bit fields
does not seem to be necessary because I did not notice
any change in audio functionality.
In an effort to clean up as many FWTS errors as possible,
I propose removing this method altogether. I have seen no
change in operation (audio works with and without this
method) and there does not seem to be any change in lspci
or dmesg.
FWTS information can be found here:
[1]: https://wiki.ubuntu.com/Kernel/Reference/fwts
This is the same change as made to Persimmon in
Change-ID If8d86f:
http://review.coreboot.org/#/c/2726/
Change-Id: Iae70c3d0af1cdaca31b206ad6daba4d38ee6b780
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2742
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
I am removing the _INI method from the AZHD device because
it does not seem to do anything and causes errors in the
FWTS[1] (Firmware Test Suite) test 'method'. The INI
method performs device specific initialization and is
run when OSPM loads a description table. It must only
access OperationRegions that have been indicated as
available by the _REG (Region) method. We do not have a
_REG method and during my testing, I added a REG method
but it did not seem to make a difference in the PCI
register space. The bit fields defined as NSDI (Disable
No Snoop), NSDO (Disable No Snoop Override), and NSEN
(Enable No Snoop Request) do not ever get written from
their default values. And writing to these bit fields
does not seem to be necessary because I did not notice
any change in audio functionality.
In an effort to clean up as many FWTS errors as possible,
I propose removing this method altogether. I have seen no
change in operation (audio works with and without this
method) and there does not seem to be any change in lspci
or dmesg.
FWTS information can be found here:
[1]: https://wiki.ubuntu.com/Kernel/Reference/fwts
This is the same change as made to Persimmon in
Change-ID If8d86f:
http://review.coreboot.org/#/c/2726/
Change-Id: Iff594d4a3493531561eb25d1cceeb97bcefde424
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2743
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Adding the 'WordBusNumber' macro to the PCI0
CRES ResourceTemplate in the Persimmon DSDT.
This sets up the bus number for the PCI0 device
and the secondary bus number in the CRS method.
This change came in response to a 'dmesg' error
which states:
'[FIRMWARE BUG]: ACPI: no secondary bus range in _CRS'
By adding the 'WordBusNumber' macro, ACPI can set
up a valid range for the PCIe downstream busses,
thereby relieving the Linux kernel from "guessing"
the valid range based off _BBN or assuming [0-0xFF].
The Linux kernel code that checks this bus range is
in `drivers/acpi/pci_root.c`. PCI busses can have
up to 256 secondary busses connected to them via
a PCI-PCI bridge. However, these busses do not
have to be sequentially numbered, so leaving out a
section of the range (eg. allowing [0-0x7F]) will
unnecessarily restrict the downstream busses.
This is the same change as made to Persimmon with
change-id I44f22:
http://review.coreboot.org/#/c/2592/
Change-Id: Ie36b60973c6a5f9076bb55c8f451532711a2f8a8
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2737
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The _OSC method is used to tell the OS what capabilities
it can take control over from the firmware. This method
is described in chapter 6.2.9 of the ACPI spec v3.0.
The method takes 4 inputs (UUID, Rev ID, Input Count,
and Capabilities Buffer) and returns a Capabilites
Buffer the same size as the input Buffer. This Buffer
is generally 3 Dwords long consisting of an Errors
Dword, a Supported Capabilities Dword, and a Control
Dword. The OS will request control of certain
capabilities and the firmware must grant or deny control
of those features. We do not want to have control over
anything so let the OS control as much as it can.
The _OSC method is required for PCIe devices and dmesg
checks for its existence and issues an error if it is
not found.
This is the same change made to Persimmon with Change-ID
I149428:
http://review.coreboot.org/#/c/2684/
Change-Id: If6dd1a558d9c319d9a41ce63588550c8e81e595f
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2738
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The _OSC method is used to tell the OS what capabilities
it can take control over from the firmware. This method
is described in chapter 6.2.9 of the ACPI spec v3.0.
The method takes 4 inputs (UUID, Rev ID, Input Count,
and Capabilities Buffer) and returns a Capabilites
Buffer the same size as the input Buffer. This Buffer
is generally 3 Dwords long consisting of an Errors
Dword, a Supported Capabilities Dword, and a Control
Dword. The OS will request control of certain
capabilities and the firmware must grant or deny control
of those features. We do not want to have control over
anything so let the OS control as much as it can.
The _OSC method is required for PCIe devices and dmesg
checks for its existence and issues an error if it is
not found.
This is the same change made to Persimmon with Change-ID
I149428:
http://review.coreboot.org/#/c/2684/
Change-Id: I2701d915338294bdade2ad334b22a51db980892e
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2739
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The _OSC method is used to tell the OS what capabilities
it can take control over from the firmware. This method
is described in chapter 6.2.9 of the ACPI spec v3.0.
The method takes 4 inputs (UUID, Rev ID, Input Count,
and Capabilities Buffer) and returns a Capabilites
Buffer the same size as the input Buffer. This Buffer
is generally 3 Dwords long consisting of an Errors
Dword, a Supported Capabilities Dword, and a Control
Dword. The OS will request control of certain
capabilities and the firmware must grant or deny control
of those features. We do not want to have control over
anything so let the OS control as much as it can.
The _OSC method is required for PCIe devices and dmesg
checks for its existence and issues an error if it is
not found.
This is the same change made to Persimmon with Change-ID
I149428:
http://review.coreboot.org/#/c/2684/
Change-Id: Iaf7b8153cec4d730efbceae3e6957d2904b8fae4
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2740
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Adding the 'WordBusNumber' macro to the PCI0
CRES ResourceTemplate in the Persimmon DSDT.
This sets up the bus number for the PCI0 device
and the secondary bus number in the CRS method.
This change came in response to a 'dmesg' error
which states:
'[FIRMWARE BUG]: ACPI: no secondary bus range in _CRS'
By adding the 'WordBusNumber' macro, ACPI can set
up a valid range for the PCIe downstream busses,
thereby relieving the Linux kernel from "guessing"
the valid range based off _BBN or assuming [0-0xFF].
The Linux kernel code that checks this bus range is
in `drivers/acpi/pci_root.c`. PCI busses can have
up to 256 secondary busses connected to them via
a PCI-PCI bridge. However, these busses do not
have to be sequentially numbered, so leaving out a
section of the range (eg. allowing [0-0x7F]) will
unnecessarily restrict the downstream busses.
This is the same change as made to Persimmon with
change-id I44f22:
http://review.coreboot.org/#/c/2592/
Change-Id: I9017a7619b3b17e0e95ad0fe46d0652499289b00
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2735
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
I am removing the _INI method from the AZHD device because
it does not seem to do anything and causes errors in the
FWTS[1] (Firmware Test Suite) test 'method'. The INI
method performs device specific initialization and is
run when OSPM loads a description table. It must only
access OperationRegions that have been indicated as
available by the _REG (Region) method. We do not have a
_REG method and during my testing, I added a REG method
but it did not seem to make a difference in the PCI
register space. The bit fields defined as NSDI (Disable
No Snoop), NSDO (Disable No Snoop Override), and NSEN
(Enable No Snoop Request) do not ever get written from
their default values. And writing to these bit fields
does not seem to be necessary because I did not notice
any change in audio functionality.
In an effort to clean up as many FWTS errors as possible,
I propose removing this method altogether. I have seen no
change in operation (audio works with and without this
method) and there does not seem to be any change in lspci
or dmesg.
FWTS information can be found here:
[1]: https://wiki.ubuntu.com/Kernel/Reference/fwts
Change-Id: If8d86f959822d528c44ab011a851659d486289b5
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2726
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The _OSC method is used to tell the OS what capabilities
it can take control over from the firmware. This method
is described in chapter 6.2.9 of the ACPI spec v3.0.
The method takes 4 inputs (UUID, Rev ID, Input Count,
and Capabilities Buffer) and returns a Capabilites
Buffer the same size as the input Buffer. This Buffer
is generally 3 Dwords long consisting of an Errors
Dword, a Supported Capabilities Dword, and a Control
Dword. The OS will request control of certain
capabilities and the firmware must grant or deny control
of those features. We do not want to have control over
anything so let the OS control as much as it can.
The _OSC method is required for PCIe devices and dmesg
checks for its existence and issues an error if it is
not found.
Change-Id: I1494285def7440972f0549b7cb73eb94dafc72c2
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2684
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The current code is attempting to convert from an invalid
starting temperature. Since we aren't sure where the temperature
will come from yet just return a static value.
This stops the kernel from going to S5 on boot because it
thinks the temperature is too high.
Change-Id: I433fa407e545458344af5842b353df5bc71bfdad
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2679
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This option is not required for haswell. Enabling the option doesn't
do anything aside from complicate mtrr calculation. Therefore, remove
it.
Change-Id: I897523ff7d3606eb89961674c2eb3d384e584857
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2678
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This commit adds support for the deveveloper, recovery,
and write protect querying. It just uses jumpers on the
Basking Ridge board.
Noted ability to togggle jumpers results in toggling the
respective modes.
Change-Id: Iac189a1fa0245654591e2e9075380db422a329a0
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2676
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
While looking at the Basking Ridge schematic I noticed some changes
and wanted to make sure they were reflected in the GPIO map.
Change-Id: I686653c164314ae9f68c42331d2f950751411d4a
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2675
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
The baskingridge has a non-zero alt_gp_smi_en value in the
devicetree.cb file. It has just to be determined which GPI
pins should trigger an SMI on basking ridge. Without this change
the board would hang during boot (presumably through a SMI flood).
No more hangs once the value is zero.
Change-Id: I9704071bb7966bd3d0bbbc4aafede3f42d829b17
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2673
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The Grays Reef CRB is deprecated by order of Intel. Basking Ridge
is the new hotness. Therefore, rename graysreef to basking ridge.
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Change-Id: I203497e165d8efc99d3438c4c548140a6e9cc649
Reviewed-on: http://review.coreboot.org/2672
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Some of the Lynx Point ids were off. Correct those and make
the pei data BAR fields consistent with the others.
Change-Id: I4102439588362cdb94643bd1ce69c9fa4278329e
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2622
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The CS5536 companion device has three different power domains.
* working domain
* standby domain
* RTC domain
When the system is "off" only the standby domain is powered.
MFGPT[7:6] are member of the standby power domain.
MFGPT7 is used to control the backlight of the device and so the
timer gets used and configured during system boot. If the system
does a reboot the timer stays configured and the Linux driver
can not use it:
"ot200-backlight: ot200-backlight.0: MFGPT 7 not availale"
The cs5535-mfgpt has a function to hard-reset all MFGPTs but the
system hangs after the first access to a MFGPT register - cause
unknown.
/*
* This is a sledgehammer that resets all MFGPT timers. This is required by
* some broken BIOSes which leave the system in an unstable state
* (TinyBIOS 0.98, for example; fixed in 0.99). It's uncertain as to
* whether or not this secret MSR can be used to release individual timers.
* Jordan tells me that he and Mitch once played w/ it, but it's unclear
* what the results of that were (and they experienced some instability).
*/
static void reset_all_timers(void)
{
uint32_t val, dummy;
/* The following undocumented bit resets the MFGPT timers */
val = 0xFF; dummy = 0;
wrmsr(MSR_MFGPT_SETUP, val, dummy);
}
After playing around with this undocumented MSR it looks like I only
need to set bit 7 to free the MFGPT7.
BTW, all MFGPT[0:5] will be reset during pll_reset().
Change-Id: I54a8d479ce495b0fc2f54db766a8d793bbb5d704
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-on: http://review.coreboot.org/2527
Tested-by: build bot (Jenkins)
Reviewed-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Even though this is under the graysreef board it really
applies to the Basking Ridge board. A subsequent patch will
rename graysreef to baskingridge.
The GPIO pins were updated to reflect the Basking Ridge schematics
as well as the DIMM spd addresses and USB over current pins.
Change-Id: Ice4e05f5203de3024cd463dfccf0bcfec1e247c1
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2632
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Add a FIXME about checking a MCHBAR register that isn't setup yet.
Also, remove revision updating because I can't find anything in the
docs that suggest this is required for haswell.
Change-Id: Ia8a6e08f82e18789e31c6c2ec2c1d63740c18dc4
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2631
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The intel-framework code has an updated pei_data structure.
Use the new structure and revision. Also, remove the scrambler
seed saving in CMOS since that appears to be handled in the saved
data from the reference code.
Change-Id: Ie09a0a00646ab040e8ceff922048981d055d5cd2
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2630
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Grays Reef is one of Intel's CRBs for the Haswell processor. The
platform is named Shark Bay.
GPIOs were the main focus so IRQ routing and ACPI still needs to be
further looked at.
Change-Id: Ie94b7af66f772714992a92612c76ca93b9b27088
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2621
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Change the OSC method to actually grant control of
PCIe capabilities to the OS instead of granting no
control. I believe the logic was backwards in the
original commit. Bits should be set when granting
control and cleared when not granting control. By
setting the return value to 0x00, we effectively
tell the OS that it cannot control any PCIe
capability. See section 6.2.9 of the ACPI spec
version 3.0 for more information.
This edit is a duplication of the OSC method that
is in the src/southbridge/intel/bd82x6x/pch.asl
file.
Change-Id: Id2462ab12203afceb9033f24d06b4dfbf2236d2e
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2714
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This enables branch prediction. We can probably find a better place
to do this, but for now we'll do it in snow's romstage main().
Change-Id: I86c7b6bc9e897a7a432c490fb96a126e81b8ce72
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2701
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Since commit »Drop redundant CHIP_NAME in mainboard.c« (a93c3fe7) [1]
`CHIP_NAME` is unneeded for mainboards as the name is composed
automatically in `src/devices/root_device.c` from the strings in
Kconfig.
Unfortunately the ports for Google Butterfly, Link and Parrot as
as well as IEI PM-LX2-800-R10 introduced CHIP_NAME again. So drop
it again too.
[1] http://review.coreboot.org/1635
Change-Id: Ice7577a2a5c6070e196f2647c440b7a8e140e27e
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2708
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Call the power_init() function. We appear to have forgotten about it
when deprecating lowlevel_init_subsystems(), but it didn't seem to
cause problems until we got to doing more interesting stuff recently.
There are some clean-ups to do from the original code, such as not
attempting to configure I2C from PMIC code, which we'll get around
to in follow-up patches.
(Credit to Gabe for spotting this)
Change-Id: I6a59379e9323277d0b61469de9abe6d651ac5bfb
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2699
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Despite everywhere the model name M5A88-V is used, in Kconfig the
string M5A88PM-V is used. Searching for that model string on the
WWW does not return anything which is unrelated to coreboot, so
change that string to M5A88-V.
Change-Id: I25cf9d4a5fc3f9b9356e8616452066ebf873f44c
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2613
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: QingPei Wang <wangqingpei@gmail.com>
Adding the 'WordBusNumber' macro to the PCI0
CRES ResourceTemplate in the Persimmon DSDT.
This sets up the bus number for the PCI0 device
and the secondary bus number in the CRS method.
This change came in response to a 'dmesg' error
which states:
'[FIRMWARE BUG]: ACPI: no secondary bus range in _CRS'
By adding the 'WordBusNumber' macro, ACPI can set
up a valid range for the PCIe downstream busses,
thereby relieving the Linux kernel from "guessing"
the valid range based off _BBN or assuming [0-0xFF].
The Linux kernel code that checks this bus range is
in `drivers/acpi/pci_root.c`. PCI busses can have
up to 256 secondary busses connected to them via
a PCI-PCI bridge. However, these busses do not
have to be sequentially numbered, so leaving out a
section of the range (eg. allowing [0-0x7F]) will
unnecessarily restrict the downstream busses.
This change will apply to other AMD mainboards and
will be in a different commit.
Change-Id: I44f22bc03a0dcbcd2594d4291508826cc2146860
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2592
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Changes:
- Get rid of the inagua mainboard specific code and use the
platform generic function wrapper that was added in change
http://review.coreboot.org/#/c/2497/
AMD f14: Add SPD read functions to wrapper code
- Move DIMM addresses into devicetree.cb
- Add the ASF init that used to be in the SPD read code into
mainboard_enable()
Notes:
- The DIMM reads only happen in romstage, so the function is not
available in ramstage. Point the read-SPD callback to a generic
function in ramstage.
Change-Id: Id05227fcf18c6ab94ffe1beb50b533ab7b0535db
Signed-off-by: Kimarie Hoot <kimarie.hoot@se-eng.com>
Reviewed-on: http://review.coreboot.org/2607
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Currently for Advansus A785E-I, ASRock E350M1 and ASUS M5A88-V
despite what is chosen in Kconfig »Chipset« menu item,
$ more .config
[…]
# CONFIG_ENABLE_IDE_COMBINED_MODE is not set
CONFIG_IDE_COMBINED_MODE=0x1
# CONFIG_SB800_SATA_IDE is not set
CONFIG_SB800_SATA_AHCI=y
# CONFIG_SB800_SATA_RAID is not set
CONFIG_SB800_SATA_MODE=0x2
[…]
the SATA controller is put into IDE mode.
$ lspci -nn | grep SATA
00:11.0 SATA controller [0106]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 SATA Controller [IDE mode] [1002:4390] (rev 40)
Commit »sb800: Add sata ahci/raid mode kconfig option«
(d4a0e7d0) [1] added the options above to configure the mode
using Kconfig and some SB800 boards were adapted already. For
example commit »persimmon: sb800 sata mode configure update«
(1386fa74) [2] did so for AMD Persimmon.
Doing the same by assigning the Kconfig variable to the value in
`platform_cfg.h` integrates this with the three remaining boards
listed above.
The patch is successfully tested with the ASRock E350M1.
$ lspci -nn | grep SATA
00:11.0 SATA controller [0106]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 SATA Controller [AHCI mode] [1002:4391] (rev 40)
[1] http://review.coreboot.org/225
[2] http://review.coreboot.org/227
Change-Id: I227257e2c8f04f18c27ff00fe62d42e372de67e4
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2610
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Replace »persimmon« by »board« in comment to keep `diff` output
between boards small.
Change-Id: Ieae2a63782c488ae35f22eb30f5b1049200d12c8
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2611
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Changes:
- Get rid of the union_station mainboard specific code and
use the platform generic function wrapper that was added
in change http://review.coreboot.org/#/c/2497/
AMD f14: Add SPD read functions to wrapper code
- Move DIMM addresses into devicetree.cb
- Add the ASF init that used to be in the SPD read code into
mainboard_enable()
Notes:
- The DIMM reads only happen in romstage, so the function is not
available in ramstage. Point the read-SPD callback to a generic
function in ramstage.
Change-Id: I19d6b0d674b67294519383f80928471b37da1e14
Signed-off-by: Kimarie Hoot <kimarie.hoot@se-eng.com>
Reviewed-on: http://review.coreboot.org/2609
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Changes:
- Get rid of the south_station mainboard specific code and
use the platform generic function wrapper that was added
in change http://review.coreboot.org/#/c/2497/
AMD f14: Add SPD read functions to wrapper code
- Move DIMM addresses into devicetree.cb
- Add the ASF init that used to be in the SPD read code into
mainboard_enable()
Notes:
- The DIMM reads only happen in romstage, so the function is not
available in ramstage. Point the read-SPD callback to a generic
function in ramstage.
Change-Id: If4291d25ea81bf375f55b64c07c223a847a211d0
Signed-off-by: Kimarie Hoot <kimarie.hoot@se-eng.com>
Reviewed-on: http://review.coreboot.org/2608
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This is previously used exception code from libpayload.
On startup it installs and then tests an exception handler.
The test is an unaligned memory operation.
Yes, we've seen what might be exceptions in the ramstage, and
it makes sense to handle them. This code is identical in structure
and operation to the previously committed payload exception handler,
though we reserve the right to change it as circumstances require.
The remaining question is whether we need it in romstage.
Change-Id: I24484686c33c9757af8ba171ebae9773828fb69d
Signed-off-by: Gabe Black <gabeblack@google.com>
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2614
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
According to BKDG:
"Memory controller (MCT) and DRAM controllers (DCTs) additions:
• Support for 933 MHz (1866 MT/s) MEMCLK frequency."
Change-Id: I6f307ce3fcb355d5445f1ea86def73a41b928a57
Signed-off-by: Konstantin Aladyshev <aladyshev@nicevt.ru>
Reviewed-on: http://review.coreboot.org/2589
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
The Hudson-E1's default SPI speed for normal i.e. non-fast reads is 66 MHz,
but the SST 25VF032B datasheet allows max. 25. Lower the speed to 22 MHz,
otherwise BIOS flashing fails.
Change-Id: I22e87d833a3ebd316b6e873595a2480831533ab1
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-on: http://review.coreboot.org/2605
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Changes:
- Get rid of the persimmon mainboard specific code which has been
moved into the wrapper as a platform generic function in change
http://review.coreboot.org/#/c/2497/
AMD f14: Add SPD read functions to wrapper code
- Move DIMM addresses into devicetree.cb
- Add the ASF init that used to be in the SPD read code into
mainboard_enable()
Notes:
- The DIMM reads only happen in romstage, so the function is not
available in ramstage. Point the read-SPD callback to a generic
function in ramstage.
Change-Id: I5f017dbb8dee5a09ec19734a6069ff9b71a6ab50
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2500
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
This adds some real GPIO mappings where virtual GPIOs were used before.
Change-Id: I25d4be45f986c8d622b97151f8bdae2651baf3e6
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2603
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Quoting Jens Rottmann [1]:
Nevertheless I still think this whole function is bogus for the E350M1. The
function assumes GPIO21 is wired to reset APU PCIe lane 0+1 (PCIe x8, port 4+5
as Coreboot/AGESA calls it), GPIO25 resets lane 2 (PCIe x4) and GPIO02 lane 3.
But the E350M1 has PCIe x16 i.e. probably APU lanes 0-3 bundled, completely
different layout. They could have chosen GPIO21 to force resets, or 25 - or
maybe 50 like on the Persimmon or any other they fancied or - and this is the
most probable - none at all. Having BiosGnbPcieSlotReset() toggle some GPIOs
without knowing what they do on the E350M1 (if anything at all) is nonsense.
In my opinion this whole function should just "return AGESA_UNSUPPORTED" and
good riddance.
[1] http://review.coreboot.org/#/c/2445/
Change-Id: Iac66da41182e838c7e6925250cc3982adbb3e4ec
Reported-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2489
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
These are essential functions for setting up the display port and
framebuffer, and also enable such things as aux channel
communications. We do some very simple initialization in romstage,
mainly set a GPIO so that the graphics is powering up, but the complex
parts are done in the ramstage. This mirrors the way in which graphics
is done in the x86 size.
I've added a first pass at a real device, and put it in the mainboard
Kconfig, hoping for corrections. Because startup is so complex,
depending on device type, I've created a 'displayport' device that
removes some of the complexity and makes the flow *much* clearer. You
can actually follow the flow by looking at the code, which is not true
on other implementations. Since display port is perhaps the main port
used on these chips, that's a reasonable compromise. All parameters of
importance are now in the device tree.
Change-Id: I56400ec9016ecb8716ec5a5dae41fdfbfff4817a
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2570
Tested-by: build bot (Jenkins)
Since the merg of the ASRock E350M1 port (a649a96e) the compiler
warns about the following [1].
mainboard.c:35, GNU Compiler 4 (gcc), Priorität: Normal
no previous prototype for 'set_pcie_reset' [-Wmissing-prototypes]
mainboard.c:43, GNU Compiler 4 (gcc), Priorität: Normal
no previous prototype for 'set_pcie_dereset' [-Wmissing-prototypes]
Adding the function prototypes to the beginning of the file as
done in commit »Persimmon updates for AMD F14 rev C0« (d7a696d0)
addresses the warning.
[1] http://qa.coreboot.org/job/coreboot-gerrit/4975/warnings13Result/package.-139448264/file.-1544928473/
[2] http://review.coreboot.org/137
Change-Id: Iad2e62ec37c3a2f749a264974b61ac7c226e9b83
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2590
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Set up the clocks used for sound and turn on the sound clock.
Change-Id: Ic59bfa9ae87116299503e6d25aeefba98c842fb8
Signed-off-by: Gabe Black <gabeblack@google.com>
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2587
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
The MMC0 on google/snow can run in 8 bit mode. To simplify driver development,
we thought disabling it (using zero, which runs in 1-bit / 4-bit mode) may help.
However, after some experiments in payload drivers, setting pinmux to 8 bit mode
can still allow MMC to run in 1-bit / 4-bit mode, so it's pretty safe to enable
8 bit mode by default for better performance.
Verified to boot on google/snow, and got MMC0 working.
Change-Id: Ic0acc723fe6a8aecf373429d3801beadd70815d9
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2585
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
The first reason for selecting the CPU model at compile time was a
multi-second pause if booting a single core Fusion T40R with MAX_CPUS=2.
Recent tests show the pause has disappeared, someone must have fixed it.
The second reason was me not knowing how to make a single vgabios image
work with two different PCI IDs. Many thanks to Martin Roth for educating
me! Quote:
"The way to make coreboot use the same vbios for different video device IDs
is through the map_oprom_vendev function. In family 14 it's in
northbridge/amd/agesa/family14/amdfam14_conf.c You would name your video
bios 1002,9802 in the config and all the other device/vendor IDs for the
family 14h processors will fall through the initial check for the video
bios and will get remapped to use that vbios. This only works if you're
initializing the vbios inside coreboot. I don't know if you're using
SeaBios as a payload, but if you are you can add the vbios to cbfs as
vgaroms/vbios.rom and the rom will always be initialized."
I'd like to add the vgabios is added as type 'optionrom' when Coreboot make
adds it, however to work with SeaBios it has to be added manually with
cbfstool and with type 'raw', or it will hang.
Change-Id: I8190d0c3202a60dfccb77dde232f9ba7ce5ce318
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-on: http://review.coreboot.org/2584
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Commit f154c018
Author: Marc Jones <marcj303@gmail.com>
Date: Wed Dec 14 11:24:00 2011 -0700
Persimmon audio codec verb patch.
Reviewed-on: http://review.coreboot.org/490
has a typo code*c* in the comments for `AZALIA_OEM_VERB_TABLE`. As
this was copied over to the LiPPERT Fam14 boards, use the following
command to fix the typo.
$ git grep -l cocec | xargs sed -i s,cocec,codec,
Change-Id: I1525b0445edab81ab136b3adece52b78ba7abc71
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2576
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
If you try to reset the system with outb(3,0x92), outb(4,0xcf9) or a
triple-fault it will instead crash with a messy screen. As the more common
outb(0xFE, 0x64) doesn't work with our setup, Linux will crash whenever you
ask it to reboot. Closer inspection shows that on a warm boot of Coreboot
agesawrapper_amdinitpost() always fails with error code 7. Looks like DDR3
re-init goes wrong somehow. I tried find the reason for this but was
unable to. I am convinced this is not board specific but a bug in AGESA.
In the end I had to settle for a workaround: if amdinitpost returns 7 this
patch resets the system harder with outb(0x06, 0x0cf9), after that RAM init
will succeed. As amdinitpost is early in POST this automatic reset is
quick enough not to be noticable.
I'd perfer a real fix, but that's all I have.
Change-Id: I4763254b489f42a135232e45328ecf0d5c4d961a
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-on: http://review.coreboot.org/2573
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Step 2: change the Persimmon code to adapt it to the new board's hardware.
The Toucan-AF is a COM Express Compact Type 6 form factor embedded board:
- AMD Fusion G-T56N (1.65 GHz dual core) or T40R (1 GHz single core) APU
- 1-4 GB DDR3 memory down
- 1x VGA, 2x DisplayPort (1 switchable to LVDS)
- AMD A55E (Hudson-E1) southbridge
- 8x USB 2.0
- 4x SATA
- HD Audio (with codec on baseboard)
- NEC uPD78F0532 microcontroller on I2C ("SEMA")
- 7x PCIe2.0 x1 (1 on PEG)
- Intel I210 GbE (on APU PCIe x1, can be disabled for additional PCIe)
- 2x SST 25VF032B (SO8, soldered) 4 MB SPI flash (BIOS and failsafe BIOS)
The Toucan-AF has no SIO on board. This patch includes basic support for a
Winbond W83627DHG (PS/2, 2x RS232), because the ADLINK ExpressBase-6 used
for evaluation happens to have one. The code may have to be adapted to the
actual baseboard of the application.
http://www.adlinktech.com/PD/web/PD_detail.php?pid=1132
Change-Id: I9041b905bad45852ac9b402fcbd5decbc98b377b
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-on: http://review.coreboot.org/2572
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Step 1: copy all files unmodified from Persimmon. This makes it much
easier later to see how the two boards actually and deliberately differ
when porting bugfixes from one to the other. Git's copy detection is
imperfect (and slow).
Change-Id: I1ff02913479c07679f8c3ae5e6dd7876e6000b55
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-on: http://review.coreboot.org/2571
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Step 1: copy all files unmodified from Persimmon. This makes it much
easier later to see how the two boards actually and deliberately differ
when porting bugfixes from one to the other. Git's copy detection is
imperfect (and slow).
Change-Id: I2fd1bf8428fc8a1e7becee888b6182b9bd8166a0
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-on: http://review.coreboot.org/2552
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
In the file `COPYING` in the coreboot repository and upstream [1]
just one space is used.
The following command was used to convert all files.
$ git grep -l 'MA 02' | xargs sed -i 's/MA 02/MA 02/'
[1] http://www.gnu.org/licenses/gpl-2.0.txt
Change-Id: Ic956dab2820a9e2ccb7841cab66966ba168f305f
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2490
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
The SD/MMC interface on Exynos 5250 must be first configured with, GPIO, and
pinmux settings before it can be detected and used in ramstage / payload.
Verified on armv7/snow and successfully boot into ramstage.
Change-Id: I26669eaaa212ab51ca72e8b7712970639a24e5c5
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2561
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This allows to drop some special cases in romstage.c
Change-Id: I53fdfcd1bb6ec21a5280afa07a40e3f0cba11c5d
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2551
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
It's not used, and not needed.
Change-Id: Ifca92f3606ac58fc26e09676488c3add5d84ae79
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2548
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
It's been on for all boards per default since several years now
and the old code path probably doesn't even work anymore. Let's
just have one consistent way of doing things.
Change-Id: I58da7fe9b89a648d9a7165d37e0e35c88c06ac7e
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2547
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Add two more GPIOs (total 6) as needed by the Google Snow laptop.
These are faking out settings for now. This code is tested and working.
Change-Id: I2077ffb8b85958eefdf54e19763d57cc1178ce89
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2538
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: build bot (Jenkins)
Commit 8487229b (Persimmon doesn't have HDMI so the GNB HD Audio should be
disabled.) turned off the device in AGESA. Now remove it from
devicetree.cb, too. This prevents the following boot message:
PCI: Left over static devices:
PCI: 00:01.1
PCI: Check your devicetree.cb.
Also clarify the line's comment a bit for the Fam14 boards which still
retain this device (to counter the loss of information ;-).
Change-Id: Ib671ed2e0d04bdef2869e8d70208d6e55cdea3fd
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-on: http://review.coreboot.org/2537
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
The PCH register bit definition for sleep type is a little confusing.
For example, 7 is S5. To make this simpler for the mainbaord developer,
the mainboard smi sleep hander is called as mainboard_sleep(slp_typ-2).
A couple mainboard SMI handlers were using the PCH define for slp_ty,
so S3 code would be run for S5 and S5 code would never be run.
Change-Id: Iaecf96bfd48cf00153600cd119760364fbdfc29e
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/2514
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Mainly replace spaces by tabs and format comments correctly.
Commit »Inagua: Indent and wihtespace cleanup« (f03360f3) [1] was
unfortunately incomplete and also used spaces instead of tabs in
some cases.
Hopefully fix this once and for all to have a template for the
other boards.
[1] http://review.coreboot.org/547
Change-Id: If15c797581dfefe2a57cd6f26e5bdac4cdd014dd
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2526
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This patch reduces unnecessary differences between AMD Inagua, Persimmon,
Union Station, South Station and Asrock E350M1. It's only cosmetical, but
makes them a little bit easier to compare.
This is the remainder of the original http://review.coreboot.org/2464,
parts of which somehow got lost in a flurry of refactoring and splitting
patches.
Change-Id: I034228be9edaaa4122506763d7bb4158f8e0ec53
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-on: http://review.coreboot.org/2529
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
Changes:
- Fix printk warnings for these two platforms by getting rid of the
l length specifier and casting to unsigned int.
This gets rid of a bunch of warnings like this one:
agesawrapper.c:279, GNU Compiler 4 (gcc), Priority: Normal
format '%lu' expects argument of type 'long unsigned int',
but argument 3 has type 'UINT32' [-Wformat]
Notes:
- This is the same change that was done for Tyan s8226 in change:
ddff32eb - http://review.coreboot.org/#/c/2451/
Tyan S8226: Fix printk warnings
- I have not tested this change on either of these platforms, I have
just compiled it.
Change-Id: I46b4c13fde7473cd2a084c7c7cb5c893f1731b02
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2502
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Changes:
- Add #include of delay.h in mainboard.c to pick up declaration of
mdelay function.
Notes:
- This fixes this warning:
mainboard.c:69, GNU Compiler 4 (gcc), Priority: Normal
implicit declaration of function 'mdelay' [-Wimplicit-function-declaration]
Change-Id: I72f333cd87215a7fc1e62d1d7ee4b2395444b03e
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2501
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Currently on for example on AMD Persimmon and ASRock E350M1 Linux
complains, that the PBLK length is invalid [1].
ACPI: Invalid PBLK length [0]
Consequently, frequency scaling might not work correctly, though for
these two boards it seems to work according to PowerTOP.
Indeed, according to the ACPI specification [2], setting PBlockLength
to 0 is only allowed if there is no PBlockAddress. Otherwise it has to
be set to 6.
18.5.93 Processor (Declare Processor)
[…]
PBlockAddress provides the system I/O address for the processors
register block. Each processor can supply a different such
address. PBlockLength is the length of the processor register
block, in bytes and is either 0 (for no P_BLK) or 6. With one
exception, all processors are required to have the same
PBlockLength. The exception is that the boot processor can have
a non-zero PBlockLength when all other processors have a zero
PBlockLength. It is valid for every processor to have a
PBlockLength of 0.
And that is exactly what Linux is checking in
`drivers/acpi/processor_driver.c` [3].
static int acpi_processor_get_info(struct acpi_device *device)
{
[…]
/*
* On some boxes several processors use the same processor bus id.
* But they are located in different scope. For example:
* \_SB.SCK0.CPU0
* \_SB.SCK1.CPU0
* Rename the processor device bus id. And the new bus id will be
* generated as the following format:
* CPU+CPU ID.
*/
sprintf(acpi_device_bid(device), "CPU%X", pr->id);
ACPI_DEBUG_PRINT((ACPI_DB_INFO, "Processor [%d:%d]\n", pr->id,
pr->acpi_id));
if (!object.processor.pblk_address)
ACPI_DEBUG_PRINT((ACPI_DB_INFO, "No PBLK (NULL address)\n"));
else if (object.processor.pblk_length != 6)
printk(KERN_ERR PREFIX "Invalid PBLK length [%d]\n",
object.processor.pblk_length);
else {
pr->throttling.address = object.processor.pblk_address;
pr->throttling.duty_offset = acpi_gbl_FADT.duty_offset;
pr->throttling.duty_width = acpi_gbl_FADT.duty_width;
pr->pblk = object.processor.pblk_address;
/*
* We don't care about error returns - we just try to mark
* these reserved so that nobody else is confused into thinking
* that this region might be unused..
*
* (In particular, allocating the IO range for Cardbus)
*/
request_region(pr->throttling.address, 6, "ACPI CPU throttle");
}
[…]
}
This issue has proliferated to all AMD based boards so fix it for
all of them by setting P_BLK length to 6.
The DSDT of for example AMD Parmer and AMD Thatcher also set it
to 6 everywhere so this solution is taken instead of setting the
P_BLK system I/O base to 0 for all but the first processor which
is how it is done for earlier AMD based boards.
As note having to set this manually should not be needed and
this should be autogenerated as done for most of the Intel boards
and the AMD K8 based boards (`src/cpu/amd/model_fxx/powernow_acpi.c`).
[1] http://www.coreboot.org/pipermail/coreboot/2013-January/073636.html
[2] http://acpi.info/DOWNLOADS/ACPIspec40a.pdf
[3] http://git.kernel.org/?p=linux/kernel/git/torvalds/linux.git;a=blob;f=drivers/acpi/processor_driver.c;h=e83311bf1ebdaaaea1adbf2de1351cca907d3465;hb=5da1f88b8b727dc3a66c52d4513e871be6d43d19#l351
Tested-by: Paul Menzel <paulepanter@users.sourceforge.net>
• ASRock E350M1:
Tested-by: Paul Menzel <paulepanter@users.sourceforge.net>
• AMD Persimmon:
Tested-by: Martin Roth <martin.roth@se-eng.com>
Change-Id: Ie79fe4812532d124cc81747c75a4f3d88d00531c
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2189
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
USB ports 0-4 are handled by PCI devices 12.0 (OHCI) and 12.2 (EHCI). 12.1
simply does not exist, so remove it from devicetree.cb. While at it make the
comment more detailed. Likewise for all USB ports.
USB device 14.6 is the Broadcom GbE MAC integrated in the Hudson-E1. Add it
to devicetree.cb. It's used on Inagua (on), but not on Persimmon (off).
Change-Id: Idea27b3390fa4470f2592e79fdd633d5a218b97b
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-on: http://review.coreboot.org/2463
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
The DSDT header contains the fields OEMID and OEM Table ID. See
for example ACPI specification 4.0a [1]
5.2.11.1 Differentiated System Description Table (DSDT)
on page 135. There Table 5-16 contains the descriptions.
Field Byte Length Byte Offset Description
===================================================
OEMID 6 10 OEM ID
OEM Table ID 8 16 The manufacture model ID.
Currently in coreboot there is no common method what to put in
these fields.
Mostly Intel based boards populate it with "CORE " ore "COREv4"
and AMD based boards populate it with the board vendor and
model number, abbreviated appropriately to fit into these fields.
On most boards the proprietary vendor BIOS seems to leave these
fields – displayed with `sudo dmidecode` under System Information –
blank
To Be Filled By O.E.M.
and fill out the Base Board Information with the board vendor and
model name.
In [2] Jens Rottmann argues that the this is really just the table
ID used for naming it and that »99% of the DSDT code is not board
specific«.
Both approaches seem to have their advantages, but using the
second one, developers often seem to forget to update them (for
example AMD Thather).
The current situation is at least not optimal. and therefore at
least unify the string in the OEM Table ID. If unifying the
OEM ID is also a good idea this should be done too.
If later on it should be decided that the board vendor and model
should be used again, this should be somehow derived from
Kconfig.
The following command was used for the change [3].
$ git grep -l '\/\* TABLE ID \*\/' | xargs sed -i '/TABLE ID/s/"\([^"]*\)"/"COREBOOT"/'
This patch is split out from [2].
[1] http://www.acpi.info/spec40a.htm
[2] http://review.coreboot.org/#/c/2464/
[3] http://stackoverflow.com/questions/5207838/sed-regex-matching-text-between-to-double-quotes-when-a-certain-text-appears-i
Change-Id: Iec98c615ce37f928abc1b500eff5aa865d772cb2
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2472
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
These were not separable or it would have been two CLs.
Enable CHROMEOS configure option on snow. Write gpio support code for
the mainboard. Right now the GPIO just returns hard-wired values for
"virtual" GPIOs.
Add a chromeos.c file for snow, needed to build.
This is tested and creates gpio table entries that our hardware can use.
Lots still missing but we can now start to fill in the blanks, since
we have enabled CHROMEOS for this board. We are getting further into
the process of actually booting a real kernel.
Change-Id: I5fdc68b0b76f9b2172271e991e11bef16f5adb27
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2467
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Similar to the discussion on the coreboot list [1]
Am Freitag, den 22.02.2013, 02:17 +0100 schrieb Peter Stuge:
[…]
> Function names should try to be descriptive. "enable_dev" is not very
> descriptive. I like "mainboard_enable" because it makes output such
> as
>
> printk("%s: foo", __func__);
>
> useful.
rename the function for the northbridge to `northbridge_enable`.
[1] http://www.coreboot.org/pipermail/coreboot/2013-February/074549.html
Change-Id: I262311ec511e394550330214621b8c37780c1d4e
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2496
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
- Fix redefinition warning for SB_GPIO_REG50 introduced in commit
fa8702cf - http://review.coreboot.org/#/c/2446/
Persimmon: adapt PCIe reset code copied from Inagua to actually
match Persimmon
The warning being fixed is:
SB800.h:1491, GNU Compiler 4 (gcc), Priority: Normal
"SB_GPIO_REG50" redefined [enabled by default]
- Enable warnings as errors so no more warnings will be accidentally
committed.
Change-Id: Ib443b2bd2067f0b7d5f93f79170899a0f8f61060
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2494
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
To reduce the differences between these file name the enabling
device function in the directory `src/mainboard` uniformly
`mainboard_enable` [1].
Thanks to the awesome help of gnomon and BlastHardcheese in the
IRC channel #sed on <irc.freenode.net>. gnomon came up with the
following command to do the actual work.
$ cd src/mainboard
$ for f in */*/mainboard.c ; \
> do src="$(awk '/\.enable_dev = /{v=$NF; sub(/,$/,"",v); print v}' "$f")" ; \
> [[ -z $src ]] && continue ; \
> printf '%s\n' "g/${src}/s/${src}\([,(]\)/mainboard_enable\1/p" w | ed -s "$f" ; \
> done
`src/mainboard/digitallogic/msm586seg/mainboard.c` and
`src/mainboard/technologic/ts5300/mainboard.c` had to be adapted
manually as no comma was used separating the struct members.
And with the following statement, gnomon is even more likable!
My pleasure entirely. Good luck with coreboot; I'm a big fan of the project.
[1] http://www.coreboot.org/pipermail/coreboot/2013-February/074548.html
Change-Id: Ife9cd0c2d9cc1ed14afc6d40063450553f06a6c6
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2493
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This is coreboot’s coding style.
Change-Id: I7441f2c1927a49a3b7171112b7798dae6b56cfb5
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2492
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Bernhard Urban <lewurm@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This is the common way to name that function, so unify that.
Change-Id: I8a01051bd304039662894b89eed53ce14dde98b6
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2491
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Ladies and gentlemen, I'm very happy to announce coreboot support for
the latest and greatest Google Chromebook: The Chromebook Pixel.
See the link below for more information on the Chromebook Pixel, and
its exciting specs:
http://www.google.com/intl/en/chrome/devices/chromebooks.html#pixel
The device is running coreboot and open source firmware on the EC
(see ChromeEC commit for more information on that exciting topic)
Change-Id: I03d00cf391bbb1a32f330793fe9058493e088571
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2482
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reduce unnecessary differences between AMD based boards only
using the file `platform_cfg.h` for configuration making them
a little bit easier to compare.
Inagua & co. mention the board name in several places which are really not
that board specific. Sometimes people even forget to change it:
Union Station’s platform_cfg.h starts with "#ifndef _PERSIMMON_CFG_H_".
Funny. Change that to "_PLATFORM_CFG_H_" everywhere.
The following command was used.
$ find . -name platform_cfg.h | xargs sed -i '/_CFG_H_/s/_.*_/_PLATFORM_CFG_H_/'
More boards seem to use that kind of naming (`git grep _CFG_H_`)
but it is not certain that this will not break anything as for
example the board AMD Dinar also has header files for
configuration stuff for the north- and southbridge.
$ git grep _CFG_H_
[…]
src/mainboard/amd/dinar/platform_cfg.h:#ifndef _PLATFORM_CFG_H_
src/mainboard/amd/dinar/platform_cfg.h:#define _PLATFORM_CFG_H_
src/mainboard/amd/dinar/platform_cfg.h:#endif //_PLATFORM_CFG_H_
src/mainboard/amd/dinar/rd890_cfg.h:#ifndef _RD890_CFG_H_
src/mainboard/amd/dinar/rd890_cfg.h:#define _RD890_CFG_H_
src/mainboard/amd/dinar/rd890_cfg.h:#endif //_RD890_CFG_H_
src/mainboard/amd/dinar/sb700_cfg.h:#ifndef _SB700_CFG_H_
src/mainboard/amd/dinar/sb700_cfg.h:#define _SB700_CFG_H_
src/mainboard/amd/dinar/sb700_cfg.h:#endif //_SB700_CFG_H
[…]
Change-Id: Ida15fa6a7adfc770240ac30e795946000dae3f16
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2464
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
At the request of Paul Menzel, I reran an
old classic of a coccinelle script:
@@
expression E;
@@
-(E + 7) & -8
+ALIGN(E, 8)
@@
expression E;
@@
-(E + 15) & -16
+ALIGN(E, 16)
Change-Id: I01da31b241585e361380f75aacf3deddb13d11c3
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/2487
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
There were just whitespace differences and three boards did not
contain
printk(BIOS_DEBUG, "alib\n");
dump_mem(ssdt, ((void *)alib) + alib->length);
which is enclosed `#if DUMP_ACPI_TABLES == 1` to dump the ACPI
tables.
Basically the whitespace in the license header in Inagua’s file
was fixed and then the file copied over to the other directories.
Change-Id: I23f73acad427b5ec14cf51651af67240871f7488
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2470
Tested-by: build bot (Jenkins)
Reviewed-by: Alvaro G. <andor@pierdelacabeza.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The following command was used to correct the typo.
$ git grep -l @breif | xargs sed -i 's/@breif/@brief/'
Change-Id: If0b579279de3c41571b9cda643836f5748a752a2
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2473
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
From ISO C99 standard: »The placement of a storage-class specifier
other than at the beginning of the declaration specifiers in a
declaration is an obsolescent feature.«
Found at <http://www.approxion.com/?p=41>.
Change-Id: Iee7878affb2a5d157a94763083689d75e8218b2f
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2474
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The relational operators in the if-predicate are aligned in all
`dimmSpd.c` files so revert part of the change in
commit 36abff1dc8
Author: Marc Jones <marcj303@gmail.com>
Date: Mon Nov 7 23:26:14 2011 -0700
Cleanup Persimmon mainboard whitespace.
Reviewed-on: http://review.coreboot.org/427
to remove the incorrectly introduced tabs and to unify that. It
might contradict the current coding style but it is even used in
the latest code as seen in the following file.
src/northbridge/amd/agesa/family15tn/dimmSpd.c
Change-Id: Ib611267f99090d0830bdc2319527389f193ea1eb
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2471
Reviewed-by: Alvaro G. <andor@pierdelacabeza.com>
Tested-by: build bot (Jenkins)
This was overlooked in the following commit.
commit 36abff1dc8
Author: Marc Jones <marcj303@gmail.com>
Date: Mon Nov 7 23:26:14 2011 -0700
Cleanup Persimmon mainboard whitespace.
Reviewed-on: http://review.coreboot.org/427
Change-Id: If6bf4836b46077614a04c1e106c241a4f97da166
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2468
Tested-by: build bot (Jenkins)
Reviewed-by: Alvaro G. <andor@pierdelacabeza.com>
For AMD Inagua, the following two commits
commit 01f7ab9335
Author: Kerry Sheh <shekairui@gmail.com>
Date: Thu Jan 19 13:18:36 2012 +0800
Inagua: Synchronize AMD/inagua mainboard.
Reviewed-on: http://review.coreboot.org/542
and
commit d91c9b7e3c
Author: efdesign98 <efdesign98@gmail.com>
Date: Thu Sep 15 10:59:55 2011 -0600
AMD Inagua platform updates
Reviewed-on: http://review.coreboot.org/136
replaced the constant `iobase` is set to by the define `SMBUS0_BASE_ADDRESS` from `OEM.h`.
Do the same for AMD Persimmon, South Station, Union station and ASRock E350M1.
Change-Id: If095cd9d9b28b118b4072c7c9d345bf620b774c9
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2453
Tested-by: build bot (Jenkins)
If CONFIG_CONSOLE_SERIAL is set, and we can call the standard function
and get a non-zero uart address, then we create an lb table entry.
The code was mostly right, just needed a tweak.
Change-Id: I5b36c7b4e580a23319b7ba92cc8ad61592b1757a
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2466
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
For whatever reason tabs got inserted in the license header text.
Remove one occurrence of that with the following command [1].
$ git grep -l 'MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.'$'\t' | xargs sed -i 's,MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.[ ]*,MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.\ \ ,'
[1] http://sed.sourceforge.net/grabbag/tutorials/sedfaq.txt
Change-Id: Iaf4ed32c32600c3b23c08f8754815b959b304882
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2460
Tested-by: build bot (Jenkins)
Reviewed-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-by: Cristian Măgherușan-Stanciu <cristi.magherusan@gmail.com>
The following commit was too eager replacing spaces with tabs.
commit 36abff1dc8
Author: Marc Jones <marcj303@gmail.com>
Date: Mon Nov 7 23:26:14 2011 -0700
Cleanup Persimmon mainboard whitespace.
Reviewed-on: http://review.coreboot.org/427
Fix that with the following command.
$ git grep -l 'Floor, Boston, MA'$'\t''02110-1301 USA' | xargs sed -i 's/Boston, MA[ ]*02110-1301 USA/Boston, MA 02110-1301 USA/'
Change-Id: Ia118a8c19d94ce1f1048280a0f1d49d447cfa2a7
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2461
Tested-by: build bot (Jenkins)
Reviewed-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-by: Cristian Măgherușan-Stanciu <cristi.magherusan@gmail.com>
Fix warning:
mptable.c:52, GNU Compiler 4 (gcc), Priority: Normal
passing argument 3 of 'mptable_write_buses' from incompatible pointer type [enabled by default]
mptable_write_buses is expecting a pointer to an int, so I changed the
U8 isa_bus to an int to match. A U8 doesn't make sense if the value could
be greater than 255 - certainly unlikely, but possible since the value
of isa_bus gets set to the maximum PCI bus number + 1.
Change-Id: I7ea416f48285922d6cf341382109993fd3f6405c
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2450
Tested-by: build bot (Jenkins)
Reviewed-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
Fix Warning:
sb700_cfg.c:129, GNU Compiler 4 (gcc), Priority: Normal
large integer implicitly truncated to unsigned type [-Woverflow]
The issue here was that an 8 bit value was being placed into a 2-bit
bitfield.
$ more src/vendorcode/amd/cimx/sb700/SBTYPE.h
[…]
UINT32 AzaliaSdin0 :2; //6
UINT32 AzaliaSdin1 :2; //8
UINT32 AzaliaSdin2 :2; //10
UINT32 AzaliaSdin3 :2; //12
$ more src/mainboard/tyan/s8226/sb700_cfg.h
[…]
* SDIN0 is define at BIT0 & BIT1
* 00 - GPIO PIN
* 01 - Reserved
* 10 - As a Azalia SDIN pin
* SDIN1 is define at BIT2 & BIT3
* SDIN2 is define at BIT4 & BIT5
* SDIN3 is define at BIT6 & BIT7
*/
#ifndef AZALIA_SDIN_PIN
#define AZALIA_SDIN_PIN 0x2A
#endif
[…]
$ more src/mainboard/tyan/s8226/sb700_cfg.c
[…]
sb_config->AzaliaSdin0 = AZALIA_SDIN_PIN;
[…]
The 8 bit value 0x2A (binary 00 10 10 10), was being used incorrectly
– I believe the original intent of this value was to enable the SDIN
pins 0, 1, & 2. Because it was getting truncated as it was put into
AzaliaSdin0, this wasn't happening and only SDIN0 was being enabled.
I am leaving only SDIN0 enabled at this point to as not change the
actual behavior on the platform.
Change-Id: Icaeb956926309dbfb5af25a36ccb842877e17a34
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2452
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Fix 84 warnings all like this one:
agesawrapper.c:289, GNU Compiler 4 (gcc), Priority: Normal
format '%lu' expects argument of type 'long unsigned int', but argument 3 has type 'UINT32' [-Wformat]
Fixed by getting rid of the l length specifier and casting to unsigned int.
Change-Id: Ic143c1034f760fa5efb2220aa33861e399ddd708
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2451
Tested-by: build bot (Jenkins)
Reviewed-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Looking at AssertSlotReset, the comments and all other case's it's
obvious this is a simple copy & paste error where someone just forgot
to change one occurrance of the GPIO nr. Also the AMD Inagua
schematics show that GPIO02 is what they really meant.
Also forward the fix to boards copied from Inagua (AMD South
Station, Union Station, Asrock E350M1).
Change-Id: I6b9a3d473245fa27604b2f148a730290277a88ed
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-on: http://review.coreboot.org/2445
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
This patch will cause the resource allocator to actually set aside
the memory resources using methods in the previous patch. The coreboot
table output will include "RAM" entries (there were none before):
coreboot memory table:
0. 0000000040400000-00000000bff001ff: RAM
1. 00000000bff00200-00000000bff00fff: CONFIGURATION TABLES
2. 00000000bff01000-00000000bfffffff: RAM
Change-Id: I5cd76e93fc232fdae1754253efb4e9269b3a20c0
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2420
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Inagua can use GPIOs 178,179 to switch VMEM to 1.5, 1.35 or 1.25 V,
which it does according to data read from the SO-DIMM's SPD EEPROM.
On Persimmon (according to DB-FT1 rev. D schematics) both GPIOs are
unconnected, there is no way to change the 1.5 V DDR3 voltage (save
unsoldering a resistor). The whole code copied over from Inagua is
useless.
Removed the code, instead a comment hints at Inagua, for people who do designs
based on Persimmon but do have a way to change VMEM.
The line ...->DDR3Voltage = VOLT1_5; is supposed to make the AGESA DDR3 code
select the RAM timings for the actually supplied voltage instead of the
hoped-for but unavailable lower voltage. I have no idea how to test this, but
in any case it can't hurt.
Change-Id: Id098e09418b665645814a6ee2d41a3bff72238ba
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-on: http://review.coreboot.org/2448
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
According to DB-FT1 rev. D schematics the APU PCIe lane 3 is unconnected.
Reflect this fact in the mainboard code.
Change-Id: Ic98f4a63ef971628df7fbf97f56b80ebe7cb8517
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-on: http://review.coreboot.org/2447
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
Comparing Persimmon and Inagua schematics and Coreboot code show the PCIe reset
code has been blindly copied even though it doesn't suit the Persimmon at all.
The Inagua can employ GPIOs 21, 25, 02 to manually reset devices on APU PCIe
lanes 0/1, 2, 3 respectively. (Appearently the motivation for this is to revive
buggy PCIe gen1 devices which got confused by PCIe gen2 signal training.)
However the Persimmon not only doesn't support this, it even needs these 3 pins
for the PCI interface! Instead it uses GPIO50 to reset devices on lanes 0-2 all
at once. Lane 3 is unconnected anyway.
This patch adapts the Persimmon mainboard code according to the DB-FT1 rev. D
schematics.
Change-Id: I05a657d9bf8cc59acc4f5174eb20375165c860c7
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-on: http://review.coreboot.org/2446
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
»Chromebook« is the official spelling [1]. So correct that with
the following command.
$ git grep -l ChromeBook | xargs sed -i s,ChromeBook,Chromebook,
The incorrect spelling was only used for the chip name.
[1] http://www.google.com/intl/en/chrome/devices/hp-pavilion-chromebook.html#hp-pav
Change-Id: I9c19f399a3e3d36bd644ec375822daa384a14961
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2370
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Marc Jones <marcj303@gmail.com>
The name lapic_cluster is a bit misleading, since the construct is not local
APIC specific by concept. As implementations and hardware change, be more
generic about our naming. This will allow us to support non-x86 systems without
adding new keywords.
Change-Id: Icd7f5fcf6f54d242eabb5e14ee151eec8d6cceb1
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2377
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This was omitted earlier while we were debugging DRAM code (0a5bc7f).
It was likely broken due to inconsistent units earlier on. Now that
things are cleaned up and working, let's add it back in.
Change-Id: I2f356355c98b2896e2371fa63b9c9f20ae76d634
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2379
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
These were left over from earlier debugging and are no longer
needed. They don't indicate any status or useful info (other
than which line of code has been executed). Error messages are
available in case something needs attention.
Change-Id: Ie09fac29c42908cb8924169e56d8927fb76f02da
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2386
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The name pci_domain was a bit misleading, since the construct is only
PCI specific in a particular (northbridge/cpu) implementation, but not
by concept. As implementations and hardware change, be more generic
about our naming. This will allow us to support non-PCI systems without
adding new keywords.
Change-Id: Ide885a1d5e15d37560c79b936a39252150560e85
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2376
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The commit introducing support for the Google Butterfly Chromebook
commit d7bd4eb003
Author: Stefan Reinauer <reinauer@chromium.org>
Date: Mon Feb 11 11:11:36 2013 -0800
Add support for "Butterfly" Chromebook
Reviewed-on: http://review.coreboot.org/2359
contains the typo, which is corrected now.
Change-Id: I932f4cd248cac71c3ede39a7da97162e791827cb
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2373
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Peter Stuge <peter@stuge.se>
Correct some whitespace inconsistencies introduced in the
following commit.
commit d7bd4eb003
Author: Stefan Reinauer <reinauer@chromium.org>
Date: Mon Feb 11 11:11:36 2013 -0800
Add support for "Butterfly" Chromebook
Reviewed-on: http://review.coreboot.org/2359
Change-Id: Ifeda7eb29ddf855cdfea41ddbd685441ede55756
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2374
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
The commits adding support for the Google Parrot Chromebook
commit a7198b34cc
Author: Stefan Reinauer <reinauer@chromium.org>
Date: Tue Dec 11 16:00:47 2012 -0800
Add support for Google Parrot Chromebook
Reviewed-on: http://review.coreboot.org/2026
and the Google Butterfly Chromebook
commit d7bd4eb003
Author: Stefan Reinauer <reinauer@chromium.org>
Date: Mon Feb 11 11:11:36 2013 -0800
Add support for "Butterfly" Chromebook
Reviewed-on: http://review.coreboot.org/2359
had macros in `fadt.c` which were not aligned correctly and did
not adhere to the coding style which uses just one space after
`#define`. Fix this and use tabs instead of spaces everywhere.
Change-Id: I1422c57a3bdc2faa29d2a6e2064e4d3aeed0f1cb
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2375
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
To simplify testing ARM implementation, we need a QEMU configuration for
ARM. The qemu-armv7 provides serial output, CBFS simulation, and full
boot path (bootblock, romstage, ramstage) to verify the boot loader
functionality.
To run with QEMU:
export QEMU_AUDIO_DRV=none
qemu-system-arm -M vexpress-a9 -m 1024M -nographic -kernel build/coreboot.rom
Verified to boot until ramstage loaded successfully by QEMU v1.0.50.
Change-Id: I1f23ffaf408199811a0756236821c7e0f2a85004
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2354
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
We're happy to announce coreboot support for the "Butterfly"
Chromebook, a.k.a HP Pavilion Chromebook.
More information at:
http://www.google.com/intl/en/chrome/devices/hp-pavilion-chromebook.html
This commit also includes support for the ENE KB3940Q embedded controller
running on Quanta's firmware.
Change-Id: I194f847a94005218ec04eeba091c3257ac459510
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2359
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins)
It was off by a few orders of magnitude. D'oh.
Change-Id: I9c8a3d5bd9ce261f914cfc7d05d86a1c61519b81
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2355
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The hardware is there, so turn it on.
Change-Id: I40aff1e84a22a05599c62b9f0b20397df0a40b15
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/2353
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
MMCONF space is defined by two config parameters:
MMCONF_BASE_ADDRESS (0xF800 0000)
MMCONF_BUS_NUMBER (64)
Coreboot allocates 1MB per bus, so MMCONF limit should be:
0xF800 0000 + 64*(0x0010 0000) - 1 = 0xFBFF FFFF
Current code does not have (-1) component, this makes MMCONF limit
equal 0xFC00 FFFF. Not 0xFC00 0000, because according to BKDG
lower two bytes of MMIO limit always equal 0xFFFF:
MMIOLimit = {MMIOLimitRegister[47:16], FFFFh}.
Add (-1) to correct this issue.
No functionality change has been experienced. The five times
slower RAM speed compared to the proprietary vendor BIOS still
remains.
Change-Id: I2c6494c28bb8d36e54ceb2aa7d8d965b0103cbe9
Signed-off-by: Konstantin Aladyshev <aladyshev@nicevt.ru>
Reviewed-on: http://review.coreboot.org/2193
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
RAMBASE and RAMTOP are leftovers from the x86 port and do not apply
the same way on ARM platforms. On x86 they refer to the low memory
region where coreboot tables reside.
However on ARM we don't have such a region which is architecturally
defined. So instead we'll use the CPU-defined DRAM base address and
the mainboard-defined DRAM size.
This also has the pleasant side-effect of fixing the coreboot tables
to not clobber ramstage code...
Change-Id: I5548ecf05e82f9d9ecec8548fabdd99cc1e39c3b
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2351
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This moves GPIO setup from chip-specific SPI code to mainboard-
specific bootblock code. This makes exynos_spi_open a bit more
generic so it can eventually be used for any SPI channel. This
also benefits CBFS since the user can set media->context to
to any set of SPI registers.
Change-Id: I2bcb9de370df0a79353c14b4d021b471ddebfacd
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2347
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This moves the setting of SPI clock rate into romstage's main,
which allows us to eliminate a bunch of dependencies from the
bootblock (about 7KB worth).
Change-Id: I371499bb4af6a6aa838294bc56f9dbc21864957a
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2346
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Except for one board, the flags can be derived from CONFIG_MMX
and CONFIG_SSE.
Change-Id: I64a11135ee7ce8676f3422b2377069a3fa78e24d
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/2336
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This cleans up Snow's trivial ramstage, gives it a coreboot table
address and calls hardwaremain().
Change-Id: I84c904bcfd57a5f9eb3969de8a496f01e43bc2f6
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2328
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Exynos system clock can be initialized before RAM init, not necessary to be in
the very beginning (boot block). This helps reducing bootblock dependency.
Verified to boot on armv7/snow.
Note: this patch was originally introduced in 2308, but there were
some ordering issues so it was reverted.
Change-Id: Ibc91c0e26ea8881751fc088754f5c6161d011b68
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2320
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Use same console initialization procedure for all ARM stages (bootblock,
romstage, and ramstage):
#include <console/console.h>
...
console_init()
...
printk(level, format, ...)
Verified to boot on armv7/snow with console messages in all stages.
Change-Id: Idd689219035e67450ea133838a2ca02f8d74557e
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2301
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The console drivers (especially serial drivers) in Kconfig were named in
different styles. This change will rename configuration names to a better naming
style.
- EARLY_CONSOLE:
Enable output in pre-ram stage. (Renamed from EARLY_SERIAL_CONSOLE
because it also supports non-serial)
- CONSOLE_SERIAL:
Enable serial output console, from one of the serial drivers. (Renamed
from SERIAL_CONSOLE because other non-serial drivers are named as
CONSOLE_XXX like CONSOLE_CBMEM)
- CONSOLE_SERIAL_UART:
Device-specific UART driver. (Renamed from
CONSOLE_SERIAL_NONSTANDARD_MEM because it may be not memory-mapped)
- HAVE_UART_SPECIAL:
A dependency for CONSOLE_SERIAL_UART.
Verified to boot on x86/qemu and armv7/snow, and still seeing console
messages in romstage for both platforms.
Change-Id: I4bea3c8fea05bbb7d78df6bc22f82414ac66f973
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2299
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
This reverts commit 9029f4b63f
This patch needs to go at the end of the UART patch set. Sorry 'bout the confusion!
Change-Id: I5702c7d6130daf95776f2c15d24e5d253691cefd
Reviewed-on: http://review.coreboot.org/2319
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Exynos system clock can be initialized before RAM init, not necessary to be in
the very beginning (boot block). This helps reducing bootblock dependency.
Verified to boot on armv7/snow.
Change-Id: Ic863e222871a157ba4279a673775b1e18c6eac0d
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2308
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
The power_init is not required on Exynos 5250 (snow) in bootblock stage. To get
a cleaner and faster bootblock, we can remove it.
Note, power_init internally calls max77686 and s3c24x0_i2c, so both files are
also removed.
Verified to boot on armv7/snow.
Change-Id: I5b15dfe5ac7bf4650565fea0afefc94a228ece29
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2317
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The I2C initialization (on component MAX77688) is already done in power_init, so
we should not need an explicit call inside bootblock.
Verified to boot on armv7/snow.
Change-Id: I68c248a8b5fee4ab838b2fb708649e112559cc41
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2316
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Remove duplicated / testing code and share more driver for bootblock, romstage
and ramstage.
The __PRE_RAM__ is now also defined in bootblock build stage, since bootblock is
executed before RAM is initialized.
Change-Id: I4f5469b1545631eee1cf9f2f5df93cbe3a58268b
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2282
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
"SPL" from U-Boot is deprecated by bootblock in coreboot/arm, so we don't need
it anymore.
Change-Id: Id16877075d0b870839a10160073ad70777a2af0a
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2297
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This attempts to clean out some dead code which was copy + pasted
into Snow's bootblock.c file, along with some unnecessary headers.
Change-Id: If9f157a52395a047c249a2a6385e0e8ddf310e59
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2291
Tested-by: build bot (Jenkins)
This patch moves ARM core and DRAM timing functions around to simplify
the dependencies for system_clock_init().
The original code was architected such that the system_clock_init()
function called other functions to obtain core and memory timings.
Due to the way memory timing information must be obtained on Snow,
which entails decoding platform-specific board straps, the bottom-
up approach resulted in having the low-level clock init code
implicitly depend on board and vendor-specific info:
main()
->system_clock_init()
-> get_arm_ratios()
-> CPU-specific code
-> clock_get_mem_timings()
-> board_get_revision()
-> read GPIOs (3-state logic)
-> Decode GPIOs in a vendor-specific manner
-> Choose memory timings from module-specific look-up table
...then proceed to init clocks
...come back to main()
The new approach gathers all board and vendor-specific info in a
more appropriate location and passes it into system_clock_init():
main()
-> get_arm_ratios()
-> CPU-specific code
-> get_mem_timings()
-> board_get_config()
-> read GPIOs (3-state logic)
-> Decode GPIOs in a vendor-specific manner
-> Choose memory timings from module-specific look-up table
-> system_clock_init()
...back to main()
Change-Id: Ie237ebff76fc2d8a4d2f4577a226ac3909e4d4e8
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2271
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This gets rid of a bunch of duplicate I2C code in the bootblock.
Change-Id: I51f625a0f738cca4ed2453fbcb78092e4110bc7e
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2289
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This gets rid of a bunch of copy + pasted GPIO code.
Change-Id: I548b2b5d63642a9da185eb7b34f80cbebf9b124f
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2288
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This gets rid of a bunch of copy + pasted code from Exynos UART
files.
Change-Id: I9fbb6d79a40a338c9fdecd495544ff207909fd37
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2286
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
The following command was used to correct the grammatical mistake.
$ git grep -l 'This is the stub function will call' | xargs sed -i s,This is the stub function will call,This stub function will call, '{}'
sed: -e Ausdruck #1, Zeichen 6: Nicht beendeter `s'-Befehl
As this file seems to have been copied around a lot, it originally
seems to have come with the following commit for AMD Persimmon and
AMD Inagua.
commit 69da1b676c
Author: Frank Vibrans <frank.vibrans@amd.com>
Date: Mon Feb 14 19:04:45 2011 +0000
Add IBASE DB-FT1 and AMD Inagua motherboards. Patch 8 of 8.
Change-Id: I2e6630a5172738b01e6def7062284f167e5508b1
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2268
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
AOpen DXPL Plus-U and Intel XE7501devkit use »COREBOOT« as
OEM Table ID.
Unify the DSDT by aligning the comments in the DSDT header with
tabs in accordance with the coding style [1].
[1] http://www.coreboot.org/Development_Guidelines#Coding_Style
Change-Id: I78e6aa8d0318b519b1df5e2178d387dc58e48323
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2278
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Mainboards using `COREBOOT` as their OEM Table ID in their DSDT
header were copied from the same source and therefore had spaces
instead of a tab to align that comment for that header field. These
are mostly Intel based boards.
Fix that in accordance with the coding style [1].
[1] http://www.coreboot.org/Development_Guidelines#Coding_Style
Change-Id: I299b955930dbd50b9717e8ff141ce8f3fd534e5f
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2277
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Snow's AP, EC, PMU, and smarty battery share a bus. Both the AP and
EC can act as a master, so to avoid conflicts an arbitration
mechanism consisting of two GPIOs is used.
By default, the AP "owns" the bus unless it is off (in which case
the EC doesn't monitor the arbitration pins). This means the boot
firmware does not need to worry about these lines. The payload may
if it needs to communicate with the EC, though.
In any case, board-specific bus arbitration logic does not belong
in a low-level driver that is supposed to be generic for an entire
CPU family. If the payload needs to talk to the EC, we'll deal with
it there.
Change-Id: I0774d4592af2b21b6ad668441532c5ceab988404
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2272
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This removes some duplicate code from Snow's mainboard bootblock
by utilizing the bootblock build class.
Change-Id: I153247370a8c5127260082dcdca3ebdc5e104fb8
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2270
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
For ARM platform, the bootblock may need more C source files to initialize
UART / SPI for loading romstage. To preventing making complex and implicit
dependency by using #include inside bootblock.c, we should add a new build class
"bootblock".
Also #ifdef __BOOT_BLOCK__ can be used to detect if the source is being compiled
for boot block.
For x86, the bootblock is limited to fewer assembly files so it's not using this
class. (Some files shared by x86 and arm in top level or lib are also changed
but nothing should be changed in x86 build process.)
Change-Id: Ia81bccc366d2082397d133d9245f7ecb33b8bc8b
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2252
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
The LVDS is on DP0, not DP1.
Change-Id: I724764d0f013e7a10d974a8716e075139982ded2
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/2259
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Mike Loptien <mike.loptien@se-eng.com>
This is a first cut at a romstage. It sets up memory, although that
needs some work; and finds and loads a ramstage.
Change-Id: I02a0eb48828500bf83c3c57d4bacb396e58bf9a5
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2245
Tested-by: build bot (Jenkins)
Continuing with the mainboard cleanup for F15tn, move the functions
to read the SPD from the mainboards for Thatcher and Parmer into the
wrapper for the northbridge/amd/agesa/family15tn.
Move the SPD address customization for the mainboard into the
devicetree.cb file.
Unrelated side note - Porting.h has an un-closed #pragma pack(1)
that can cause confusing side-effects. AGESA's structures all
use this, but coreboot's don't. Be sure to include the coreboot
.h files BEFORE Porting.h is included, not after.
This fix has been tested.
Change-Id: I89cdd225be61f60c6b8e7020e6f8b879983bbd96
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2190
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
This replaces the current stage-specific exit/entry functions with
generic versions. Now all stages compile with stage_entry(), which
is placed at .text.stage_entry.armv7, and stage_exit().
Snow's ramstage files are also updated to avoid build breakage.
Change-Id: I953a2c4b8121bd4b66c3362557997a9ca3aa53b0
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2254
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
The SPI flash driver for Exynos chipset.
Verified to boot on snow/armv7.
Change-Id: I7eef67a9c57f825d09f13ea44c2b59b54345fa7b
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2229
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Summary:
Isolate CBFS underlying I/O to board/arch-specific implementations as
"media stream", to allow loading and booting romstage on non-x86.
CBFS functions now all take a new "media source" parameter; use
CBFS_DEFAULT_MEDIA if you simply want to load from main firmware.
API Changes:
cbfs_find => cbfs_get_file.
cbfs_find_file => cbfs_get_file_content.
cbfs_get_file => cbfs_get_file_content with correct type.
CBFS used to work only on memory-mapped ROM (all x86). For platforms like ARM,
the ROM may come from USB, UART, or SPI -- any serial devices and not available
for memory mapping.
To support these devices (and allowing CBFS to read from multiple source
at the same time), CBFS operations are now virtual-ized into "cbfs_media". To
simplify porting existing code, every media source must support both "reading
into pre-allocated memory (read)" and "read and return an allocated buffer
(map)". For devices without native memory-mapped ROM, "cbfs_simple_buffer*"
provides simple memory mapping simulation.
Every CBFS function now takes a cbfs_media* as parameter. CBFS_DEFAULT_MEDIA
is defined for CBFS functions to automatically initialize a per-board default
media (CBFS will internally calls init_default_cbfs_media). Also revised CBFS
function names relying on memory mapped backend (ex, "cbfs_find" => actually
loads files). Now we only have two getters:
struct cbfs_file *entry = cbfs_get_file(media, name);
void *data = cbfs_get_file_content(CBFS_DEFAULT_MEDIA, name, type);
Test results:
- Verified to work on x86/qemu.
- Compiles on ARM, and follow up commit will provide working SPI driver.
Change-Id: Iac911ded25a6f2feffbf3101a81364625bb07746
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2182
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
[…]
CC romstage.inc
src/mainboard/asrock/e350m1/romstage.c: In function 'cache_as_ram_main':
src/mainboard/asrock/e350m1/romstage.c:48:5: warning: unused variable 'reg8' [-Wunused-variable]
This change was already done for AMD Persimmon in the following
commit.
commit d7a696d0f2
Author: efdesign98 <efdesign98@gmail.com>
Date: Thu Sep 15 15:24:26 2011 -0600
Persimmon updates for AMD F14 rev C0
Change-Id: I8f1ae1a609b87b197583934f0556f66b64e6994d
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2230
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
The previous incarnation did not use all of mmu_setup, which meant
we did not carefully disable things before (possibly) changing them.
This code is tested and works, and it's a bit of a simplification.
Change-Id: I0560f9b8e25f31cd90e34304d6ec987fc5c87699
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2204
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: build bot (Jenkins)
This change is required in order to use a LVDS panel
attached to the LVDS connector.
Change-Id: Id97c233f964151b6515bd46c797425d0e6690cbd
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/2188
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
commit 585a400697
Author: zbao <fishbaozi@gmail.com>
Date: Thu Apr 12 11:27:26 2012 +0800
Leverage the Pstate table created by AGESA.
… introduced unneeded whitespace in front of a comma.
Revert that part of the above commit. In the file for AMD Dinar
tabs and spaces are mixed, but leave that alone for the beginning.
Change-Id: I279cd0cb0be8c79258034733773f2ae1c2207cce
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2187
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Enable 'all warnings being treated as errors' in thatcher and parmer.
Fixed the following warnings on parmer / thatcher:
src/vendorcode/amd/agesa/f15tn/Proc/CPU/Feature/cpuFeatureLeveling.c:
In function 'GetGlobalCpuFeatureListAddress':
src/vendorcode/amd/agesa/f15tn/Proc/CPU/Feature/cpuFeatureLeveling.c:291:14:
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
src/vendorcode/amd/agesa/f15tn/Proc/CPU/S3.c:
In function 'SaveDeviceContext':
src/vendorcode/amd/agesa/f15tn/Proc/CPU/S3.c:245:18:
warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
src/vendorcode/amd/agesa/f15tn/Proc/CPU/S3.c:309:16:
warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
src/vendorcode/amd/agesa/f15tn/Proc/CPU/cpuPostInit.c:
In function 'GetPstateGatherDataAddressAtPost':
src/vendorcode/amd/agesa/f15tn/Proc/CPU/cpuPostInit.c:235:10:
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
src/vendorcode/amd/agesa/f15tn/Proc/Mem/NB/TN/mntn.c:
In function 'MemNInitNBDataTN':
src/vendorcode/amd/agesa/f15tn/Proc/Mem/NB/TN/mntn.c:353:32:
warning: assignment from incompatible pointer type [enabled by default]
src/vendorcode/amd/agesa/f15tn/Proc/Mem/NB/TN/mntn.c:363:23:
warning: assignment from incompatible pointer type [enabled by default]
src/vendorcode/amd/agesa/f15tn/Proc/CPU/Feature/cpuFeatureLeveling.c:
In function 'GetGlobalCpuFeatureListAddress':
src/vendorcode/amd/agesa/f15tn/Proc/CPU/Feature/cpuFeatureLeveling.c:291:14:
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
src/vendorcode/amd/agesa/f15tn/Proc/CPU/S3.c:
In function 'SaveDeviceContext':
src/vendorcode/amd/agesa/f15tn/Proc/CPU/S3.c:245:18:
warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
src/vendorcode/amd/agesa/f15tn/Proc/CPU/S3.c:309:16:
warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
In file included from src/northbridge/amd/agesa/family15tn/northbridge.c:37:0:
src/vendorcode/amd/agesa/f15tn/AGESA.h:1547:0:
warning: "TOP_MEM" redefined [enabled by default]
src/include/cpu/amd/mtrr.h:31:0:
note: this is the location of the previous definition
src/vendorcode/amd/agesa/f15tn/AGESA.h:1548:0:
warning: "TOP_MEM2" redefined [enabled by default]
src/include/cpu/amd/mtrr.h:34:0:
note: this is the location of the previous definition
In file included from src/northbridge/amd/agesa/family15tn/northbridge.c:41:0:
src/vendorcode/amd/agesa/f15tn/Proc/CPU/cpuRegisters.h:378:0:
warning: "LOCAL_APIC_ADDR" redefined [enabled by default]
src/include/cpu/x86/lapic_def.h:9:0: note:
this is the location of the previous definition
In file included from src/mainboard/amd/parmer/BiosCallOuts.h:24:0,
from src/mainboard/amd/parmer/mainboard.c:28:
src/vendorcode/amd/agesa/f15tn/AGESA.h:1547:0:
warning: "TOP_MEM" redefined [enabled by default]
src/include/cpu/amd/mtrr.h:31:0:
note: this is the location of the previous definition
src/vendorcode/amd/agesa/f15tn/AGESA.h:1548:0:
warning: "TOP_MEM2" redefined [enabled by default]
src/include/cpu/amd/mtrr.h:34:0: note:
this is the location of the previous definition
Change-Id: Iecea28232f1761401cf09f7d2a77d3fbac2f5801
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2171
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Go through southbridge/amd/agesa/hudson, thatcher and parmer
mainboard directories and change all references to sb800 to
reference hudson instead.
This is just cleanup and should make no functional difference.
Change-Id: Icd6a9a08c4bbf5e1aed394362d24c05811ed1fba
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2177
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
There are currently too many things in the mainboard directories that
are really more suited to being in the northbridge / southbridge
wrappers. This is a start at moving some of those functions down
into the wrappers.
Move the bios callback functions into the northbridge/amd/agesa/family15tn
directory from the mainboard directories. These can still be overridden
by any mainboard just by updating the pointer in the callback table to
point to a customized version of the function.
Change-Id: Icefaa014f4a4abbe51870aee7aa2fa1164e324c1
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2169
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
Add Kconfig option for Legacy free and hook it into the parmer
AGESA initialization as well as the FADT code. This should really
be done inside the southbridge wrapper and not in the mainboard,
but for now the code to attach it to is inside the mainboard.
Update Kconfig for parmer and thatcher to default to legacy free.
Change-Id: Ib899bd02ddc5506caae4aca2c589cc2526638cb8
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2157
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
Re-formatting and cleaning up the devicetree.cb files for
parmer and thatcher.
Change-Id: Ic458e59701c1f2593b0a035b96cac60df476ee82
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2164
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
The way that devicetree.cb was configured for the family 15tn boards
was doing... interesting things to the video device initialization.
This was causing S3 resume to fail.
There is a disconnect between how the devicetree should be configured
if there are multiple HT links on the CPU and how it's configured if
there's only one HT link. These platforms were set up as if they
had multiple HT links, which was causing duplicate instances of
devices in the device list.
The scan for the IO Hub was removed from the northbridge code which
isn't a problem for F15tn devices.
Change-Id: I3556b43027746e36b07de7cb1bece4d1b37a3c34
Signed-off-by: Martin Roth <martin@se-eng.com>
Reviewed-on: http://review.coreboot.org/2160
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
This patch does a few things to get us into romstage:
- Add romstage as a stage (a later patch adds it as a binary, which
is probably wrong). The Makefile magic is complex enough that we
let it build the XIP file for now, but we no longer use it.
- Replace findstage with loadstage. Loadstage will find a stage,
load the code to memory, and zero the remaining part of memory.
Now we can link the romstage to go anywhere!
- Eliminate magic offsets from code/ldscripts and centralize Kconfig
variables in src/cpu/samsung/exynos5250/Kconfig.
- Tidy up code and serial output
Change-Id: Iae4d2f9e7f429cb1df15d49daf9a08b88d75d79d
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2174
Tested-by: build bot (Jenkins)
This adds a wrapper around main() in romstage which is compiled using
-marm. This assumes that the bootblock branches to romstage in ARM
mode.
The long-term idea is to enforce ABI compatibility when handing off to
the next stage by using shims which are which are compiled in a pre-
determiend manner and leave the main portions of each stage up to
whatever the compiler wants. So it will eventually look like this:
1. bootblock_main (ARM/Thumb)
2. bootblock_exit (ARM)
3. romstage_entry (ARM)
4. romstage_main (ARM/Thumb)
(credit to Gabe Black for writing the patch, I'm just uploading it)
Change-Id: I4fdb8d2c6c2c0a7178bcb9154c378ddce0567309
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/2175
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This is the bloated Snow bootblock which includes:
- SPI driver
- UART, including requisite I2C, Maxim PMIC, and clock config code.
- Adjustments for magic offsets (id section, stack pointer address)
This is just a temporary solution until we have romstage loading.
Once that happens, we'll rip out all but the code necessary for
copying SPI ROM content into SRAM.
Change-Id: I2a11e272eb9b6f626b5d9783eabb4a720a1d06be
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2170
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Our earlier attempt was jumping straight from asm to the old u-boot
board_init_f in lowlevel_init_c.c. We are getting ready to transition
to using a real bootblock for ARM, so add romstage.c to the files
compiled and we'll make main() our entry point.
This also updates romstage.ld to place main() (*(.text.startup)) at
the beginning of romstage.
Change-Id: Ifc77a6bfba27d915c4cad62c6c8040665294628a
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2163
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
We don't pass any arguments into romstage on ARM.
Change-Id: I018f28a57fc486c9240345cf0f4043b79027d864
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2162
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Bits were being shifted off the end of the mask accidentally.
This results in all masks being 32 bits wide instead of 48.
Change-Id: I5f4d1b6a323df1aa4568ff4491f82447b8a2f839
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2146
Tested-by: build bot (Jenkins)
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The high bits of mtrr mask are MBZ (Must be zero). Writing 1 to these
bits will cause exception. So be carefull when spread this change.
The supermicro/h8scm needs more work. Currently it is set as it was.
We need to check if the F10 and F15 have different value.
Change-Id: I2dd8bf07ecee2fe4d1721cec6b21623556e68947
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1661
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
This replaces 0x02023400 with an SoC-specific Kconfig variable.
Change-Id: I21482d54a1e1fa6c4437c030ddae2b0bb3331551
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2130
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
ACPI code:
The ACPI code is not currently being compiled in by default, but
assuming that it will be at some point, I'm fixing the loop that
waits for the IMC to respond after sending it a command. The
loop now exits after 500ms, similar to the function in agesa.
Agesa Code:
a 16 bit variable will always be less than 100000. Change to
be a 32 bit variable.
Change-Id: I9430ef900a22d056871b744f3b1511abdfea516e
Signed-off-by: Martin Roth <martin@se-eng.com>
Reviewed-on: http://review.coreboot.org/2119
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This patch switches the Qemu target to use (pseudo) Cache As RAM
and enables some ACPI code. This allows to use the CBMEM console
and timestamp code with coreboot in Qemu. Right now, the ACPI code
is commented out because leaving it in breaks IDE.
Change-Id: Ie20f3ecc194004f354ae3437b9cf9175382cadf8
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2113
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
There are two CPUs on s8226 and each CPU has 8 cores.
CPU 0 takes lapic from 0x10 to 0x17 and CPU 1 takes from 0x20 to 0x27.
So the first core's lapic is 0x10 rather than 0x20.
Change-Id: I925114d44f2f4974eb62c3832d8c9139a2a06c96
Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com>
Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/2099
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This mirrors the naming convention of handlers in
northbridge and southbridge.
Change-Id: I45d97c569991c955f0ae54ce909d8c267e9a5173
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/2058
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This imports SPL (second phase loader) files from U-Boot. Most of the
content of these files will eventually go away since they're fairly
U-Boot specific. For now they are here to make Jenkins happy.
Change-Id: Ib3a365ecb9dc304b20f7c1c06665aad2c0c53e69
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2081
Tested-by: build bot (Jenkins)
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
I have issues when AmdReadEventLog function tries to use BiosCallouts interface.
So it is necessary to provide callout pointer to this function.
Change-Id: I4080e5f07d5d28c41688b2a7deff944b7a0f7bf7
Signed-off-by: Aladyshev Konstantin <aladyshev@nicevt.ru>
Reviewed-on: http://review.coreboot.org/2064
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
This commit enables the external graphics card.
In order to work, the internal graphic card has to be
disabled, that is done in src/device/device.c through:
vga_onboard->ops->disable(vga_onboard);
which calls the RS780 disable operation introduced in the following
commit: "rs780: add .disable pcie_ops"
This commit was tested with and without the following card:
02:00.0 VGA compatible controller: nVidia Corporation GT218 [GeForce 210] (rev a2)
Thanks Aladyshev for the pointer(in the #coreboot IRC channel on Freenode servers):
Dec 20 19:43:32 <Aladyshev> If you list your internal card in devicetree.cb,
coreboot will distinguish external and internal VGA and choose external one
Change-Id: I92e59dffd158db096a6e99d1ef6e2e248fef933c
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Reviewed-on: http://review.coreboot.org/2067
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Fix some minor discrepancies which prevented the MAX77676 from
getting compiled in properly.
Change-Id: Ib29136da6c15a4bdb24926a91729431c507cd209
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2076
Tested-by: build bot (Jenkins)
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Supermicro H8QGI has integrated Matrox G200 16MB DDR2 graphics.
List it in devicetree.cb to mark it as onboard VGA to coreboot.
This change makes menuconfig option "Use onboard VGA as primary video device" work.
Change-Id: Ia6b9f60e3ae705689f22babd544ad6e628a85df1
Signed-off-by: Aladyshev Konstantin <aladyshev@nicevt.ru>
Reviewed-on: http://review.coreboot.org/2042
Tested-by: build bot (Jenkins)
Reviewed-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
Fix little mistake in get_bus_conf code
Change-Id: I8c09e501082caa0a20266b007c0744630a356de0
Signed-off-by: Aladyshev Konstantin <aladyshev@nicevt.ru>
Reviewed-on: http://review.coreboot.org/2046
Tested-by: build bot (Jenkins)
Reviewed-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
Size of BiosCallouts[] struct can be calculated as:
CallOutCount = sizeof (BiosCallouts) / sizeof (BiosCallouts [0]);
There is no longer need for REQUIRED_CALLOUTS define.
Originally that change was done for AMD Persimmon in
commit d7a696d0f2
Author: efdesign98 <efdesign98@gmail.com>
Date: Thu Sep 15 15:24:26 2011 -0600
Persimmon updates for AMD F14 rev C0
without deleting the define. This was ported to some of the other
boards and for some the define was not removed.
The AMD Inagua, Parmer and Thatcher boards were already adapted but
the define was left in. So just remove it for those.
Tested on Supermicro H8QGI.
Change-Id: Ia09795579a1170fa20ab94a30feb1af6821153d2
Signed-off-by: Aladyshev Konstantin <aladyshev@nicevt.ru>
Reviewed-on: http://review.coreboot.org/2049
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin@se-eng.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
H8QGI board has 2 IO-APICS with 56 IRQ’s:
IOAPIC[0]: GSI 0-23 - SB700 southbridge
IOAPIC[1]: GSI 24-55 - RD890 northbridge
`gDefaultApicDeviceInfoTable[]` structure in northbridge code
vendorcode/amd/cimx/rd890/nbIoApic.c
has IO-APIC interrupt mapping for HT and IOMMU set to last 31
IRQ pin (24+31=55).
CONST APIC_DEVICE_INFO gDefaultApicDeviceInfoTable[] = {
// Group Swizzling Port Int Pin
{0, 0, 31}, //HT
{0, 0, 31}, //IOMMU
[…]
Also the same value (55) can be found in original Supermicro BIOS ACPI DSDT.
Change-Id: Ie26da1f773716d1b7f5f5f884050ae799afc0b7e
Signed-off-by: Aladyshev Konstantin <aladyshev@nicevt.ru>
Reviewed-on: http://review.coreboot.org/2047
Tested-by: build bot (Jenkins)
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Add configuration for AMD's IMC ROM and fan registers for cimx/sb800
platforms.
- Allows user to add the IMC rom to the build and to configure the
location of the "signature" between the allowed positions.
- Allows for no fan control, manual setup of SB800 Fan registers, or
setup of the IMC fan configuration registers.
- Register configuration is done through devicetree.cb. No files need
to be added for new platform configuration.
- Initial setup is for Persimmon, but may be extended to any cimx/sb800
platform.
Change-Id: Ib06408d794988cbb29eed6adbeeadea8b2629bae
Signed-off-by: Martin Roth <martin@se-eng.com>
Reviewed-on: http://review.coreboot.org/1977
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Marc Jones <marcj303@gmail.com>
This is the minimal set of sources that allow the board to build.
These need to be filled in with actual code. But if we get these in upstream
we can stop working against a WIP patch.
Change-Id: I9347a573bb40761f6a12be3ee8febe3ca4be55a3
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2018
Tested-by: build bot (Jenkins)
Supermicro h8scm has a C32 CPU socket, the details of this board is:
http://www.supermicro.com/Aplus/motherboard/Opteron4100/SR56x0/H8SCM-F.cfm
We are planning to replace legacy C32 code with agesa and the h8scm_fam10 do not support
family 15 CPU, so we update this mainboard with this patch.
This code supports memory at 800M Hz of f10 CPU, bu f15 CPU does not has this limitation.
If you want to change the frequency of memory, please edit the macros
"BLDCFG_MEMORY_BUS_FREQUENCY_LIMIT" and "BLDCFG_MEMORY_CLOCK_SELECT"
in src/mainboard/supermicro/h8scm/buildOpts.c
Change-Id: I9ca9e70d7f3e82c07e7d36695bf31008db152afb
Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com>
Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/1510
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
Change-Id: I4b735fe4e6441f99236e43b34695fdac95b8888a
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/1875
Tested-by: build bot (Jenkins)
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
Not sure why this never triggered an error before.
Change-Id: I85d8b3b862492df04163a5f751c7ea4288406860
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1946
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
As we move to supporting other systems we need to get rid of assembly
where we can. The log2 function in src/lib is identical to the assembly
one (tested for all 32-bit signed integers :-) and takes about 10 ns
to run as opposed to 5ns for the non-portable assembly version. While speed
is good, I think we can spare the 15 ns or so we add to boot time
by using the C version only.
Change-Id: Icafa565eae282c85fa5fc01b3bd1f110cd9aaa91
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/1928
Tested-by: build bot (Jenkins)
This gets rid of the somewhat unstructured placement of AMD's
sysinfo structure in CAR.
We used to carve out some CAR space using a Kconfig variable,
and then put sysinfo there manually (by "virtue" of pointer magic).
Now it's a variable with the CAR_GLOBAL qualifier, and build
system magic.
For this, the following steps were done (but must happen together
since the intermediates won't build):
- Add new CAR_GLOBAL sysinfo_car
- point all sysinfo pointers to sysinfo_car instead of GLOBAL_VAR
- remove DCACHE_RAM_GLOBAL_VAR_SIZE
- from CAR setup (no need to reserve the space)
- commented out code (that was commented out for years)
- only copy sizeof(sysinfo) into RAM after ram init, where
before it copied the whole GLOBAL_VAR area.
- from Kconfig
Change-Id: I3cbcccd883ca6751326c8e32afde2eb0c91229ed
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/1887
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Marc Jones <marcj303@gmail.com>
This broke because those components were not yet
committed when the patch to drop the driver class
was made.
Change-Id: I29948223503a6c4b196eafa169c064cd26da1be1
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1934
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
- Optionally override FSB clock detection in generic
LAPIC code with constant value.
- Override on AMD Model fxx, 10xxx, agesa CPUs with 200MHz
- compile LAPIC code for romstage, too
- Remove #include ".../apic_timer.c" in AMD based mainboards
- Remove custom udelay implementation from intel northbridges' romstages
Future work:
- remove the compile time special case
(requires some cpuid based switching)
- drop northbridge udelay implementations (i945, i5000) if
not required anymore (eg. can SMM use the LAPIC timer?)
Change-Id: I25bacaa2163f5e96ab7f3eaf1994ab6899eff054
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1618
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
When dropping ramstage.a, unused functions with unresolved
symbols are not silently dropped anymore. This makes the
tim5690 compilation fail.
This fix makes sure we don't compile in the int15 handler code
when we don't set CONFIG_VGA_ROM_RUN
Change-Id: If6872c983d9fd811eb33259421f94b551f3b9b34
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1929
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
When dropping ramstage.a duplicate symbols in ramstage
will start breaking the build. Hence drop all the duplicate
functions implemented by mainboards that have those functions
in generic or component code already.
Change-Id: I5cf8245c67b6f0f348388db54256d28f47017a61
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1865
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
The use of ramstage.a required the build system to handle some
object files in a special way, which were put in the drivers
class.
These object files didn't provide any symbols that were used
directly (but only via linker magic), and so the linker never
considered them for inclusion.
With ramstage.a gone, we can drop this special class, too.
Change-Id: I6f1369e08d7d12266b506a5597c3a139c5c41a55
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1872
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The calculation of COMB's irq reading was wrong by the 4-bit shift.
Also, the asl compiler warned about the splitting in lo/hi bytes which
seems unnecessary.
Change-Id: Ia5101d5a19f68c2da827d7e37a18922f959604c7
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1923
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Forgot to update the rk9 for the unified VGABIOS handling.
This applies to rk9 what is done for other boards in commits
3c84261e84d5d340695b
Change-Id: I892b7d81927e277778c1c5251d27416fa79c9868
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1924
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Roda RK9 is a notebook based on the GM45/ICH9 platform using DDR3 memory.
http://roda-computer.com/products/notebooks/rk9/
Tested with various Linux versions, known to work:
- 2x4GB RAM
- IGD
- HD Audio
- UHCI, EHCI
- AHCI
- NIC
- PCI
- PS/2 keyboard
- serial console
- ACPI lid switch
- ACPI battery/AC events
- power off, reboot
Change-Id: I7299dccbff2eea3544363fdd4f49f05aa3dae7bc
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1691
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Some boards have two instances of the int15 handler that supports
the onboard VGA BIOS, for YABEL and realmode.
These are now similar enough that they can be deduplicated.
Due to minor differences this requires manual effort.
Change-Id: I03ae314cb90dd65d96591ce448504aa961cbeb88
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1893
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Makes it more similar to what realmode looks like.
Change-Id: I4407431f2d979c43dd186114d67ed11845907afe
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1892
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
By using the (global) register file as defined by x86emu,
we can use the same register access for YABEL and realmode
interrupt handlers.
- the x86 realmode interrupt handlers changed in signature
- to access registers, use X86_$REGNAME now (eg. X86_EAX)
- x86_exception_handler still uses struct eregs *regs to
avoid spilling the x86emu register file stuff everywhere
Coccinelle script that handled most of this commit:
@ inthandler @
identifier FUNC, regs;
@@
int FUNC(
-struct eregs *regs
+void
)
{ ... }
@ depends on inthandler @
identifier regs;
@@
-regs->eax
+X86_EAX
@ depends on inthandler @
identifier regs;
@@
-regs->ebx
+X86_EBX
@ depends on inthandler @
identifier regs;
@@
-regs->ecx
+X86_ECX
@ depends on inthandler @
identifier regs;
@@
-regs->edx
+X86_EDX
@ depends on inthandler @
identifier regs;
@@
-regs->esi
+X86_ESI
@ depends on inthandler @
identifier regs;
@@
-regs->edi
+X86_EDI
@ depends on inthandler @
identifier regs;
@@
-regs->eflags
+X86_EFLAGS
@ depends on inthandler @
identifier regs;
@@
-regs->vector
+M.x86.intno
Change-Id: I60cc2c36646fe4b7f97457b1e297e3df086daa36
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1891
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
realmode int handlers must return the same codes as the YABEL
int handlers now: 1 for "interrupt handled", 0 for "not handled"
(ie. error).
Change-Id: Idc01cf64e2c97150fc4643671a0bc4cca2ae6668
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1890
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Change-Id: I4128af7912bec090bbd48acc1b20d0452e7a4a28
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/1876
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
e.g.
-#if CONFIG_LOGICAL_CPUS == 1
+#if CONFIG_LOGICAL_CPUS
This will make it easier to switch over to use the config_enabled()
macro later on.
Change-Id: I0bcf223669318a7b1105534087c7675a74c1dd8a
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1874
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This code used a special case for checksum calculation to
prevent the century byte from messing things up, since
writes "sometimes" didn't happen.
That should be stable now, so the special case isn't necessary.
Downside: On century rollovers (ie. 1999-12-31, 2099-12-31)
CMOS will be reset to the defaults.
Change-Id: Ibe589a1ec953b7b3ba39be30cebd9fc2b27326ae
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1870
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
intel_irq_routing_table is a local structure that should not be used
globally, because it might not be there on all mainboards.
Instead, the API has to be corrected to allow passing a PIRQ table in
where needed.
Change-Id: Icf08928b67727a366639b648bf6aac8e1a87e765
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1862
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Some boards selected GENERATE_ instead of HAVE_
Change-Id: I450c22d7b044f0c88c21692246d452d516a68a83
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1841
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
hard_reset was indeed consolidated and moved into the southbridge
code a while ago, but the config variable was still kept alife, with
some duplicate code.
Change-Id: I60d4a87de916667f6e89353dfbe1a7b9eca380f7
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1837
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
- Add mainboard_smi.c from arch/x86/Makefile if it's there
- Add mainboard's chromeos.c from the chromeos Makefile
Change-Id: I3f80e2cb368f88d2a38036895a19f3576dd9553b
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1835
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This patch is the beginning of a Kconfig cleanup series
- drop CONFIG_HAVE_BUS_CONFIG and add get_bus_conf.c if it
exists in the mainboard directory
- drop duplicate ACPI_SSDTX_NUM from mainboard Kconfig
if it only defines the defaul value of 0
- Add mptable.c, fadt.c, reset.c and ssdtX.asl when they
exist, not based on some Kconfig magic
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Change-Id: Ia14a7116dad6a724af7e531920fee9a51fd0b200
Reviewed-on: http://review.coreboot.org/1832
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The board incorrectly overrides the southbridge hook, so use the
new mainboard hook instead. This change also activates the actual
southbridge hook to enable decode of complete 4 MB flash memory region.
Change-Id: I02c6fe89ae9ad4a7403f024fac875ebd88a8e142
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1831
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
It's a bool, not a number
Change-Id: I70d52c6af6703101dbd534970ec65275902a283d
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1842
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The board was broken for use with CONFIG_PCI_OPTION_ROM_RUN_YABEL.
Change-Id: Ia57d630143386fe637af83b9e7345d0d3750b089
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1854
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Some time ago our CMOS checksum algorithm was changed under the topic:
Fix our CMOS checksum algorithm so it matches what /dev/nvram expects
Here is another copy of the algorithm that had to be updated.
Change-Id: I58659c7b8a89c89c76efdff405ee0620e7302277
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1852
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
At boot time when the ACPI tables are created and the location
of GNVS is determined then save that address for resume time.
This also sets the values of USB charging in S3/S5 to the expected
default values for Stout/Butterfly that were not set correctly.
Change-Id: I9b94b868aa6e81aced06c0262cc2697ad4faf1e6
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1768
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Using global variables with the TSEG is a bad idea because
they are not relocated properly right now. Instead make
the variables static and add accessor functions for the
rest of SMM to use.
At the same time drop the tcg/smi1 pointers as they are
not setup or ever used. (the debug output is added back
in a subsequent commit)
Change-Id: If0b2d47df4e482ead71bf713c1ef748da840073b
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1764
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
ChromeOS' top of the tree u-boot expects coreboot to export information
about option ROM status (started/not started). Stumpy and Lumpy were
left behind and are not exporting this information. This CL fixes the
problem.
Change-Id: Id90035bd76ab177e4fc269efc2b74f15f641c77d
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/1713
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Fix GPIO exporting for new Vboot for oprom-matters GPIO
and to make the power button static.
Change-Id: Ic042c428a1d43512228c686121fa057d876606e1
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1761
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Right now coreboot's build process produces images that are
not booting on actual hardware because they are smaller than
the actual flash device and also don't have an IFD nor an ME
firmware in them. In order to produce bootable images, you
needed a wrapper script / extra step until now. With this
change, the resulting coreboot.rom is actually bootable.
Change-Id: I82714069fb004d4badc41698747a704bd9fed4da
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1771
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
If these values are non-zero then the kernel will issue
an SMI for each core (cstate) and package (pstate).
Since we don't do anything with these SMI callbacks we
can avoid taking the extra SMIs at boot time by zeroing
these fields.
Change-Id: I3bc5fe0a9f45141d46884cb77ecdfaeaa45d2439
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1769
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
On Sandybridge and Ivybridge systems the firmware image has to
store a lot more than just coreboot, including:
- a firmware descriptor
- Intel Management Engine firmware
- MRC cache information
This option allows to limit the size of the CBFS portion in
the firmware image.
Change-Id: Ib87fd16fff2a6811cf898d611c966b90c939c50f
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1770
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This makes resume from S3 work again. The check is new and fails on
other boards, too.
Change-Id: I0ada569e4ba649b9ac82768b0888e16104c621e8
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1809
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Compose the name from Kconfig strings instead.
As the field is for debug print use only, a minor change in the output
should do no harm. The strings no longer include word "Mainboard".
Change-Id: Ifd24f408271eb5a5d1a08a317512ef00cb537ee2
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1635
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
All of these capabilities exist on all CPUs supported on
this socket.
Change-Id: I54f34e48e34bb6ab5b9954ab7ece8c2c3a1a8e67
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1664
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Because enable cache is added at the end of disable_cache_as_ram,
( http://review.coreboot.org/#/c/1662/2/src/cpu/amd/agesa/cache_as_ram.inc )
enable_cache() should be removed. The 3 mainboards are: amd parmer,
amd thatcher and tyan s8226
Change-Id: If870ca07d2e97b9e860a2e2315f551251c7a4ed2
Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com>
Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/1669
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
We had only some MSR definitions in there, which are used in speedstep
related code. I think speedstep.h is the better and less confusing place
for these.
Change-Id: I1eddea72c1e2d3b2f651468b08b3c6f88b713149
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1655
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Enable the PCIE bridge which is connected to the PCIE slot.
Change-Id: I1b3fb59990e06d7bc7cf19639f2b93dbb7bf9b3e
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1098
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
We only want to add data once per device. Using the one in
chip_operations is not very usable anyway, as different
devices under the same chip directory would need to output
entirely different sets of data.
Change-Id: I96690c4c699667343ebef44a7f3de1f974cf6d6d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1492
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins)
The PCI registers should be accessed aligned and 0x62 is not 32bit
aligned therefore this patch changes it to a 16bit access.
Change-Id: I00725a4569f471eedb061834f626911b42e734fb
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-on: http://review.coreboot.org/1631
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
This is not available as a config option anymore.
Change-Id: Icac173d62928423a08671321ec21d4af82c5cded
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-on: http://review.coreboot.org/1630
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
Change-Id: I2f10909a626fb64c7f95663ddd79a3b899f73bc4
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1606
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
The used FPGA on the device triggers PIRQD for the membrane
keyboard. The used linux driver for the keyboard uses the fixed
IRQ number of 7. In order not to touch the linux driver and be
compatible with proprietary BIOS change the irq_table in
coreboot.
Change-Id: If5bc929eb48bb1eafd401941ebb7d34cf5862c35
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-on: http://review.coreboot.org/1571
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
HPET's min ticks (minimum time between events to avoid
losing interrupts) is chipset specific, so move it to
Kconfig.
Via also has a special base address, so move it as well.
Apart from these (and the base address was already #defined),
the table is very uniform.
Change-Id: I848a2e2b0b16021c7ee5ba99097fa6a5886c3286
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/1562
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Also deletes files not included in build:
src/southbridge/amd/cimx/sb700/chip_name.c
src/southbridge/amd/cimx/sb800/chip_name.c
src/southbridge/amd/cimx/sb900/chip_name.c
Change-Id: I2068e3859157b758ccea0ca91fa47d09a8639361
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1473
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
According to file "northbridge.c" in family 15h code
IO-HUB should be placed on link_lsit[0] in devicetree.cb.
This hack in "northbridge.c" was made to satisfy both f10 and f15 cpu's.
Change-Id: I4754235bd38239460347b0dc4a82cd4e58ae7cd0
Signed-off-by: Kostr <aladyshev@nicevt.ru>
Reviewed-on: http://review.coreboot.org/1540
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
The previous commit provides a mainboard_interrupt_handlers
implementation YABEL with identical semantics to the
x86emu one, so let's use it in both cases.
This eliminates the need for the int15_install()
indirection, so let's drop that, too.
Generated using the following coccinelle patch and
manual cleanups (empty #if/#endif):
@@
type T;
identifier FUNCARR;
expression INT, HANDLER;
@@
-typedef T yabel_handleIntFunc;
-extern yabel_handleIntFunc FUNCARR[256];
-FUNCARR[INT] = HANDLER;
+mainboard_interrupt_handlers(INT, &HANDLER);
@@
@@
-void int15_install(void)
-{
-mainboard_interrupt_handlers(0x15, &int15_handler);
-}
@@
@@
-void int15_install(void)
-{
-mainboard_interrupt_handlers(0x15, &int15_handler); ... mainboard_interrupt_handlers(0x15, &int15_handler);
-}
@@
@@
-int15_install();
+mainboard_interrupt_handlers(0x15, &int15_handler);
Change-Id: I70fd780d7ebf1564a2ff7d7148411673f6de113c
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/1559
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
our code supports tyan s8226 now, which has two cpus on the board
the cpu socket is C32. The details of tyan s8226 is:
http://www.tyan.com/product_SKU_spec.aspx?ProductType=MB&pid=679&SKU=600000190
the test result of this mainboard is:
1) boot Ubunbu 11.10, kernel 3.0.9. there is no err and warnings in
dmesg.
2) boot windows7 x64 successfully.
3) use fwts to test the bios, there are 268 pass and 14 failed
4) pcie and usb slots are ok.
5) all network interfaces are ok.
Change-Id: I7d8534f20b4f3c16322a5c5ba2e3fba4b4f3e608
Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com>
Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/1495
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
Currently the C32 has some legacy boards which use the old C32 code. We need to seperate them.
CONFIG_CPU_AMD_SOCKET_C32 was used in legacy code before.
But it is not a good idea, so we change the code as follows:
So we use CONFIG_CPU_AMD_SOCKET_C32 to identify mainboard which uses agesa code,
and use CONFIG_CPU_AMD_SOCKET_C32_NON_AGESA to identify mainboard which uses legacy code.
Change-Id: If6114bf8912e78b7732f25a1adfb2e4d8eb10ee4
Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com>
Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/1497
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
In the field there are different hardware revisions and some
of them have problems with UDMA as a resistor is missing. We can
detect this situation in coreboot and e.g. the linux kernel
can take this knowledge and disable UDMA.
Change-Id: Ib75cad7acedbc1dc65378bb9bfc3f353cbe21427
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-on: http://review.coreboot.org/1512
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This eeprom is used to store some device relevant informations
like hardware revision.
Change-Id: I32bda9d5412bc5a96da0edb5ef0b6d1ba4caa2d8
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-on: http://review.coreboot.org/1511
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Without this change 64 bit versions of Windows will BSOD.
Change-Id: If39627a179c24184b6c956b3a50f692f8a034d2f
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/1476
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
The M2V-MX SE DSDT has been a copy from Asus A8V-E SE, which has VT8237R.
But the stuble change in USB interrupt routing went undetected, although
I had some USB troubles on the FOSDEM with low speed devices.
Change-Id: Ie724df440e0963f6955b3de57e4687f3ddc7f6ef
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Reviewed-on: http://review.coreboot.org/1505
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
Without this change 64 bit versions of Windows will BSOD.
Change-Id: Ica4b79d798a269399341868b1c793ce745aa93fc
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/1480
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The name is derived directly from the device path.
Change-Id: If2053d14f0e38a5ee0159b47a66d45ff3dff649a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1471
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
The includes removed here were previously required for
struct lb_memory and lb_add_memory_range().
Change-Id: Ie6c0d4ef55c2225aa709cf3fbad30ff1080e3610
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1391
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
Stefan Reinauer