Use w83627hf_set_clksel_48() where needed instead or open-coding the same
functionality, and also use w83627hf_enable_serial() instead of
w83627hf_enable_dev() (which does exactly the same, but isn't wrapped in the
enter/exit config mode functions).
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6143 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
De-asserts STRAP_BIF_all_valid for
PCIE-GFX core.
After lane reversal,
Asserts STRAP_BIF_all_valid for
PCIE-GFX core.
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Acked-by: QingPei Wang <wangqingpei@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6142 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
W83627DHG:
- Add proper "virtual LDN" handling for the LDNs that need it (i.e., those
that don't have their "enable" bit in bit 0 of the 0x30 register).
- Fix various I/O masks in the pnp_dev_info[] array as per
datasheet. Add missing PNP_IRQ0 to the W83627DHG_ACPI LDN.
W83627EHG:
- Similar to W83627DHG, improve the "virtual LDN" setup a bit (it was
mostly implemented already, though).
- Add missing PNP_IRQ0 to the W83627EHG_ACPI LDN.
Also: Fix up devicetree.cb of all boards using W83627DHG/W83627EHG to adapt
for the virtual LDNs.
include/device/pnp.h: Add comment that 'function' (which refers to the
LDN and should probably be renamed later) has to be at least 16 bits
wide. In theory LDNs could use u8, but due to the virtual LDN info being
encoded in the "high byte" of 'function' it must be at least u16.
asrock/939a785gmh/romstage.c: Drop unused GPIO6_DEV.
ibase/mb899/romstage.c: Use DUMMY_DEV instead of a specific LDN (serial
port 1 in this case) to avoid confusion. The global registers
manipulated there are accessible from any LDN.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6140 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6138 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The read-modify-write wasn't needed. This is easier to understand.
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6136 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6135 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Single channel (in slot DDR1 and DDR3) produces strange artefacts on screen (and hang)
Dual Channel (in DDR1 and DDR2 aka blue slot) - works nice
All slots populated - same case as Single channel - must be something wrong with UMA.
Tested with 2x 512MB CAS 2.5 DDR400
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6134 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
> Stefan Reinauer wrote:
> > The specified IO port is most likely wrong. As the comment mentions, the
> > SSDT is a good place for that. A preprocessor define used both in the
> > CPU init code and in the asl would solve the problem without an SSDT.
> > For some info on CPU SSDT creation on intel check out
> > src/cpu/intel/speedstep/acpi.c
>
> The IO port is ok (and I wrote the comment myself ;)):
> DEFAULT_PMBASE is 0xe400
> PCNTRL reg offset is 0x10
>
> Using the preprocessor will probably work too if iasl can do simple
> arithmetic (likely yes), I'll look into that.
BTW, my first idea was to use an acpi method that looks up pmbase in
the pci cfg space, but when I define a method like this:
Method(TEST, 2)
{
Return (Add(Arg0, Arg1))
}
I get:
|build/mainboard/asus/p2b/dsdt.ramstage.asl 9: Processor (CPU0,
|0x01, TEST(0xe400, 0x10), 0x06) {}
|Error 4096 - syntax error, unexpected PARSEOP_NAMESEG,
|expecting ')' ^
While using the builtin Add() directly works.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6132 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
I cleaned up the patch and moved most of the dsdt.dsl and
acpi_tables.c into the southbrige/northbridge directory.
Updated patch should fix abuild error and incorporates suggestions
on irc by uwe (thanks for the comments).
Thanks to Idwer Vollering <vidwer@gmail.com> for the original patch.
Tested:
Linux (poweroff, powerbutton event)
XP (poweroff, powerbutton event)
Abuild-tested
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6127 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
In bcm5785_enable_rom(): Use PCI IDs from pci_ids.h instead of hardcoding,
and use 'dev' instead of 'addr' as device_t variable name.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6126 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6125 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also, add missing license header to amd8111_enable_rom.c, add some more code
comments and use PCI IDs from pci_ids.h instead of hardcoding.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6124 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also, move CONFIG_HT_CHAIN_END_UNITID_BASE #ifdef block to mcp55.h to make
the build work (but this is a good idea anyway, as it's used in
multiple files).
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6123 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This adds the board-specific parts for S3 support on the M2V board.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6122 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
initialized properly because the pcie link takes some time to come
up.
I set the timeout rather arbitrary to 100ms, this is what a BIOS_ERR
and higher only boot looks like on my system (with pcie printks set
to BIOS_ERR so they show up):
|Device error
|Device error
|PCI: 00:02.0 PCIe link up after 35800 us
|PCI: 00:03.0 PCIe link up after 12900 us
|PCI: 00:03.1 PCIe link timeout
|PCI: 00:03.2 PCIe link up after 32000 us
|APIC: 00 missing read_resources
|I2C: 01:50 missing read_resources
|I2C: 01:51 missing read_resources
|I2C: 01:52 missing read_resources
|I2C: 01:53 missing read_resources
|Start bios (version pre-0.6.2-20101025_023503-nukunuku)
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6121 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
AMD RS780 uma graphics. Tested with frame buffer sizes 64m through 1GB
by running dxdiag and Windows media player at 1600x1200 true color.
Additional changes needed to boot Win7 on Mahogany_fam10 will follow.
-- Enable and program the debug bar as required by the ATI graphics driver.
First, make the debug bar writable and allow resource allocation code
to program it. Once programmed, enable its operation.
-- Disable the family 10h processor mmconf while the RS780 mmconf is in use.
-- Make strap programming more closely follow the reference BIOS.
-- Disable PCIe bar 3 after using it.
-- UMA size is no longer hardcoded.
-- Disable write combining for all steppings to eliminate stability problem.
-- Correct task file data.
-- Improve the accuracy of the Atom table that passes information to the driver.
Signed-off-by: Scott Duplichan <scott@notabs.org>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6120 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
using it directly again.
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6118 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2) the patch implements get_cbmem_toc in chipset specific way if defined.
On Intel targets it should be unchanged. On K8T890 the the cbmem_toc is read from NVRAM. Why you ask? Because we cannot do it as on intel, because the framebuffer might be there making it hard to look for it in memory (and remember we need it so early that everying is uncached)
3) The patch removes hardcoded limits for suspend/resume save area (it was 1MB) on intel. Now it computes right numbers itself.
4) it impelements saving the memory during CAR to reserved range in sane way. First the sysinfo area (CAR data) is copied, then the rest after car is disabled (cached copy is used). I changed bit also the the copy of CAR area is now done uncached for target which I feel is more right.
I think I did not change the Intel suspend/resume behaviour but best would be if someone can test it. Please note this patch was unfinished on my drive since ages and it would be very nice to get it in to prevent bit rotten it again.
Now I feel it is done good way and should not break anything. I did a test with abuild and it seems fine.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6117 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This should probably be C code in some .c file anyway.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6116 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Every board had a slightly different invokation, very often commented out
anyway. We could either decide that this is only to be used by developers
during bringup (and thus added manually to romstage.c and removed before
the board gets committed). This method seems to be preferred from what I
have heard on IRC / mailing list in the past.
Or, we add the ram_check() somewhere globally and allow the user to enable
it via menuconfig (possibly only if EXPERT is selected).
Either way, the current method of spreading the calls all over the place is
not really the way to go.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6115 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6114 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6113 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This needlessly complicates the code and increases register pressure on romcc
chipsets. We did the same conversion on i440BX, i830, and others.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6112 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
initializing VGA happens pretty much as the last thing before starting the
payload. Hence, drop VGA console support, as we did in coreboot v3.
- Drop VGA and BTEXT console support.
Console is meant to be debugging only, and by the time graphics comes up
99% of the risky stuff has already happened. Note: This patch does not remove
hardware init but only the actual output functionality.
The ragexl driver needs some extra love, but that's for another day
- factor out die() and post()
- drop some leftover RAMBASE < 0x100000 checks.
Signed-off-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: QingPei Wang<wangqingpei@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6111 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Mention full name of all the tables (SSDT, FADT, etc).
- Drop obsolete / incorrect "LXBIOS" reference.
- Add missing ACPI address space type #defines specified in newer versions:
ACPI_ADDRESS_SPACE_EC, ACPI_ADDRESS_SPACE_SMBUS.
- Add missing "enum acpi_apic_types" entries: Localx2Apic, Localx2ApicNMI.
- Add ACPI_FACS_64BIT_WAKE_F #define.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6110 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
default on all boards) into Kconfig.
Signed-off-by: Jonathan Kollasch <jakllsch@kollasch.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6109 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also, remove some less useful comments, some dead code / unused functions.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6108 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also drop some dead or useless code snippets.
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6107 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6106 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6105 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
not brought over to Kconfig (this applies to all #defines to 4, as
that's the default anyway)
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6104 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The (0xa << 3) expression equals 0x50, i.e. DIMM0.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6103 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Except for one instance the spd_addr.h were now very tiny, there's not
much point in keeping that stuff in an extra file. The only user of those
files is the romstage.c file anyway.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6101 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- VIA VT8235: Do the shift in smbus_read_byte() as all other chipsets do.
- spd.h: Move RC00-RC63 #defines here, they were duplicated in lots of
romstage.c files and lots of spd_addr.h files. Don't even bother for
those spd_addr.h which aren't even actually used, drop them right away.
- Replace various 0x50 hardcoded numbers with DIMM0, 0x51 with DIMM1,
and 0xa0 with (DIMM0 << 1) where appropriate.
- Various debug.c files: Replace SMBUS_MEM_DEVICE_START with DIMM0,
SMBUS_MEM_DEVICE_END with DIMM7, and drop useless SMBUS_MEM_DEVICE_INC.
- VIA VX800: Drop unused SMBUS_ADDR_CH* #defines.
- VIA VT8623: Do the shift in smbus_read_byte() as all other chipsets do.
Then, replace 0xa0 (which now becomes 0x50) with DIMM0.
- alix1c/romstage.c, alix2d/romstage.c: Adapt to recent bit shift changes.
- Various files: Drop DIMM_SPD_BASE and/or replace it with DIMM0.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6100 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
addressing scheme to match the rest of the tree
(0x50 instead of 0xa0).
abuild tested.
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6099 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Fix whitespace, coding style, and indentation in some places.
- Add comments for less obvious entries and hardcoded numbers (e.g. 'type').
- Add comments for all/most 'revision' fields, mention in which version
of the ACPI spec which revision number is to be used.
- Add URLs to a few external documents which describe tables that are
not mentioned in the ACPI spec (or where the external document may
provide further info), e.g. SRAT, SLIT, HPET, MCFG, etc.
- Use the ASLC #define instead of hardcoding "CORE" in one instance
(ASLC is already used everywhere else).
- Add some TODOs for additional stuff which is in the spec but not yet
handled by our code / #defines.
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6098 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- s/Options.lb/devicetree.cb/
- s/Config.lb/devicetree.cb/
- s/cache_as_ram_auto.c/romstage.c/
- h8dmr_fam10/README: Drop obsolete comment, we have mc_patch_01000086.h in
the tree now.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6095 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6089 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
chipset code (where it belongs)
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6088 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6087 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
deselected it, and very likely there won't ever be any
hardware that requires it deselected.
Keep the "selected" code path around, leading to no
functional change.
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Scott Duplichan <scott@notabs.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6086 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6085 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Updated patch with improved comments and small bugfix (use same
value for min and max on io resource).
While adding the area between TOM1 and 4GB to \SB.PCI0._CRS seems to be the
easiest way to get both Linux and Windows happy, it is not quite correct
because reserved areas like APIC, MMCONF etc. ranges need to be excluded.
This is a proof of concept patch for the M2V board that dynamically creates a
ResourceTemplate() containing these in the SSDT and adds a corresponding
PNP0C02 device to the DSDT.
All resources that have IORESOURCE_RESERVE and (IORESOURCE_MEM or IORESOURCE_IO) set
are added.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Added M2V-MX SE too.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6084 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
as an ACPI motherboard resource or it will not enable MMCONFIG
and the extended pcie configuration area will be unaccessible:
This patch adds the IORESOURCE_RESERVE flag to the APIC and MMCONF
resource flags to do this.
I also added a new resource for the mapped bios rom area just below 4GB.
I'm not sure if the choice for the index parameter of new_resource()
is correct though.
Note that the bios rom decode is enabled in
src/southbridge/via/vt8237r/vt8237r_early_smbus.c
for the whole 4MB area (even though the comment says 1MB).
Ruik: I extended the flash range to 16MB (This is what VT8237S can decode)
Remove the MMCONFIG region reserve in the mainboard file (this patch makes it obsolete)
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6083 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
http://tracker.coreboot.org/trac/coreboot/changeset/3953
Note that all corresponding DSDTs only ever check TOM2 against 0.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6082 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CONFIG_PIRQ_ROUTE) so far is the amd cs5530.
Add one for vt8237 too.
Setting up the pci routing is important in case you want to boot DOS,
OSes that don't support ACPI or MP tables and ROMs for add-in storage
controllers may depend on this too.
TODO: Fix the 4 routing links limitation in
src/arch/i386/boot/pirq_routing.c
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6081 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The only difference is that the "G" version is in a Pb-free package, which
is not relevant from a programmer's view.
We keep W83627THG (and drop W83627THF) because:
- The W83627THF had a CIR device / LDN which doesn't actually exist.
- The W83627THF had no GPIO2, GPIO3 LDNs (were commented out).
- The W83627THF didn't use the PNP_MSC0/1 which is needed/used by boards.
This also fixes an issue on MSI MS7135's devicetree.cb:
device pnp 4e.6 off end # XXX keep allocator happy
The line above can be (and is) removed, as it was only needed due to the
incorrect CIR LDN in the W83627THF.
In the iwill/dk8x target: Drop incorrect LDNs 4 and 6, add 0xb.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6080 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6079 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6078 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
make their defaults more obvious.
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6077 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6074 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Random coding style, whitespace and cosmetic fixes.
- Consistently use the same spacing and 4-hexdigit port number format
in the pnp_dev_info[] arrays.
- Drop dead/unused code and less useful comments.
- Add missing "(C)" characters and copyright years.
- Shorten and simplify some code snippets.
- Use u8/u16/etc. everywhere.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6073 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
For now this is a plain copy of the ASUS A8V-E SE target, I reported
that most of the code also works (sort of) for the ASUS A8V-E Deluxe
a long while ago, see
http://www.coreboot.org/pipermail/coreboot/2008-March/031866.htmlhttp://www.coreboot.org/ASUS_A8V-E_Deluxe
There will be a bunch of changes necessary though (devicetree.cb, mptable.c,
ACPI, etc) which do not apply to the A8V-E SE, so we need an extra target.
Also: Increase ID_SECTION_OFFSET on the VIA K8T890/K8M890 southbridge, as
otherwise there will be build errors if the MAINBOARD_PART_NUMBER string
gets too long (as is the case for "A8V-E Deluxe"). The error is:
ld: section .id loaded at [00000000ffffffd2,00000000ffffffef] overlaps
section .romstrap loaded at [00000000ffffff80,00000000ffffffd3]
(both with stock Debian gcc and with xgcc)
Increase ID_SECTION_OFFSET (default 0x10) to 0x80 as other southbridges do.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6072 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Add a few more comments for the entries, and also change the devicetree.cb
files to the more compact and better readable variant with indentation level
of 2 spaces (instead of random mix of tabs and spaces).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6071 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6070 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
an override function in m2v/mainboard.c
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6069 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
cablesel |= (sb->ide0_80pin_cable << 28) |
(sb->ide0_80pin_cable << 20) |
(sb->ide1_80pin_cable << 12) |
(sb->ide1_80pin_cable << 4);
in vt8237r_ide.c ends up doing
cablesel |= 0xfffffff0;
(with both bits set to 1) which is probably not the intended result. ;)
After a short discussion on irc the consensus was to change the
bitfields to u8 as it's probably not worth it using bitfields here.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6068 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
-- When building for UMA, reduce the limit for DRAM below 4GB
from E0000000 to C0000000. This is needed to accomodate the
UMA frame buffer.
-- Correct problem where msr C0010010 bits 21 and 22 (MtrrTom2En
and Tom2ForceMemTypeWB) are not set consistently across cores.
-- Enable TOM2 only if DRAM is present above 4GB.
-- Use AMD Tom2ForceMemTypeWB feature to avoid the need for
variable MTRR ranges above 4GB.
-- Add above4gb flag argument to function x86_setup_var_mtrrs. Clearing
this flag causes x86_setup_var_mtrrs() to omit MTRR ranges for
DRAM above 4GB. AMD systems use this option to conserve MTRRs.
-- Northbridge.c change to deduct UMA memory from DRAM size reported
by ram_resource. This corrects a problem where mtrr.c generates an
unexpected variable MTRR range.
-- Correct problem causing build failure when CONFIG_GFXUMA=1 and
CONFIG_VAR_MTRR_HOLE=0.
-- Reserve the UMA DRAM range for AMD K8 as is already done for AMD
family 10h.
Tested with mahogany on ECS A780G-GM with 2GB and 4GB.
Tested with mahogany_fam10 on ECS A780G-GM with 2GB and 4GB.
Signed-off-by: Scott Duplichan <scott@notabs.org>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6067 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The power-on default is 1.95V, set the DDR2 voltage to
standards-conforming 1.8V.
I also measured with a multimeter to confirm this.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6066 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The pc_keyboard_init() function no longer takes any base addresses
since r5152 (passed in via res0/res1 variables previously), so drop them.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6063 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
I missed this one since it was working anyway, since
"The LPC BIOS ROM is always accessed when ISA addresses
FFF80000-FFFFFFFF and 000F0000-000FFFFF are decoded" (VT8237R datasheet)
And the rom I use for testing is smaller than this 512KB default range.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6062 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Needed to change class from raid to ide so seabios can boot from it.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6061 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- i3100_early_serial.c:
- Split out enter/exit functions as the other Super I/Os do.
- Make i3100_enable_serial() take a device_t as usual, and convert
it to use the standard pnp_* function instead of open-coding
the same functionality by hand.
- Factor out i3100_configure_uart_clk() from i3100_enable_serial(),
we do the same in various other Super I/Os, e.g. ITE ones.
- Add some #defines for register / bit values and some comments.
- Only functional change: Don't set bit 1 of SIW_CONFIGURATION, it's
marked as "READ ONLY, WRITES IGNORED" in the datasheet.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6058 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Whitespace, coding style, and typo fixes.
- Drop unused/obsolete "#config chip.h".
- Use u8/u16/etc. everywhere.
- Use pnp_read_config()/pnp_write_config() instead of open-coding them.
- Use pnp_set_logical_device() instead of open-coding it.
- W83627EHG: Fix incorrect enable_hwm_smbus() code comment.
- Use ARRAY_SIZE.
- w83627hf/superio.c: w83627hf_16_bit_addr_qual(): Bugfix, the code was using
'dev->path.pnp.port >> 8' as config port, which is incorrect in superio.c
(which has a "real" device_t struct, in contrast to *_early_serial.c which
uses "unsigned" as device_t where 'dev >> 8' is required).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6057 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The function is called with no format specifiers in the first parameter
throughout the code, so it needs to work also with just one parameter.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6056 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Hook up malloc() debug code via CONFIG_DEBUG_MALLOC. Only show it in
menuconfig if at least DEBUG or SPEW are selected as loglevel, as this
code does additional printk(BIOS_DEBUG, ...) calls which would otherwise
not be visible anyway.
- Similarly, make DEBUG_CAR and REALMODE_DEBUG only visible if thr DEBUG or
SPEW loglevel is selected.
- Get rid of a custom "debug" macro, use printk() as usual.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6054 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- it8661f_enable_serial() is now in the usual format, using pnp_* functions.
- Factor out pnp_enter_ext_func_mode()/pnp_exit_ext_func_mode().
- Factor out it8661f_set_clkin() to set the CLKIN to 24/48MHz.
- Factor out it8661f_enable_logical_devices(), might not be needed though.
We leave it here until it's confirmed on hardware that it's not needed.
- Move some #defines to it8661f.h.
- Drop no longer used it8661f_sio_write().
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6053 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Linux kernel, which was previously complaining that the MTRR setup
is wrong, if the cpu supports more than CONFIG_CPU_ADDR_BITS bits of
address space.
Shamelessly copied from Linux arch/x86/kernel/cpu/mtrr/main.c
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Scott Duplichan <scott@notabs.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6052 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This patch fixes a hang on
supermicro/h8dme
supermicro/h8dmr
supermicro/h8dmr_fam10
and possibly on other mcp55-based boards.
Signed-off-by: Ward Vandewege <ward@gnu.org>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6048 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Drop some of the less useful / outdated / duplicated comments.
- Simplify and streamline some code to look like the other Super I/Os.
- Use u8/16/etc. everywhere.
- ITE IT8718F: Add missing GPIO LDN.
- Add missing braces around SIO_DATA #defines, potential bug even.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6047 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
compatible. The extended cmos is accessed differently for AMD
and Intel RTCs. Not sure what if any OS cares about this distinction,
but non-Intel compatible seems like a safer way to report the AMD RTC.
Tested with Win7 on Mahogany_fam10 and kino-780am2-fam10.
Signed-off-by: Scott Duplichan <scott@notabs.org>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6046 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This adds the m2v directory and necessary files to src/mainboards/asus and
adjusts the Kconfig.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6045 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
adjusts the Kconfig.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6044 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
"Use get_vt8237_lpc() in vt8237_sb_enable_fid_vid()" patches.
This adds VT8237A specific VLINK/LPC init in vt8237r_early_smbus.c
I ran some tests and apparently both the
| /* So the chip knows we are on AMD. */
| pci_write_config8(devctl, 0x7c, 0x7f);
and
| /*
| * Allow SLP# signal to assert LDTSTOP_L.
| * Will work for C3 and for FID/VID change.
| */
| outb(0x1, VT8237R_ACPI_IO_BASE + 0x11);
in vt8237r_early_smbus.c are needed on VT8237A, otherwise I get a (non-fatal)
fid/vid change error on boot.
While vt8237a_vlink_init() in vt8237_ctrl.c is a modified vt8237r_vlink_init(),
vt8237a_init() in vt8237r_lpc.c is a modified vt8237s_init().
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6043 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Depends on the "Introduce get_vt8237_lpc() function" patch.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6042 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
I broke this out into a seperate part to keep the other half as
straight-forward as possible.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6041 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
add a get_vt8237_lpc() function.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6040 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
http://linux.via.com.tw/ as VX800 seems to be compatible.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6039 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
and vt8237r_lpc.c.
While vt8237a_vlink_init() in vt8237_ctrl.c is a modified vt8237r_vlink_init(),
vt8237a_init() in vt8237r_lpc.c is a modified vt8237s_init().
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6038 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Rudolf
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6037 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6036 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
other place, and that defines these symbols itself (and
identical, too). Drop them.
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6034 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
All other uses of these symbols have their own (identical)
definitions.
abuild-tested and trivial
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6031 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- VIA VT1211:
- Add missing LDNs and respective code to handle them.
- Add some TODOs for other stuff that needs fixing.
- Use VT1211_SP1 instead of hardcoding the LDN number (2).
- Fixup pnp_dev_info[] as per datasheet, but some TODOs remain.
- Various coding style fixes and changes to u8/u16/etc.
- Serverengines Pilot: Various coding style fixes and changes to u8/u16/etc.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6030 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Use HAVE_ACPI_TABLES, HAVE_MP_TABLE, and HAVE_PIRQ_TABLE (instead of
GENERATE_*) in the board's Kconfig file, as all other boards do.
- Add missing HAVE_ACPI_TABLES/HAVE_MP_TABLE/HAVE_PIRQ_TABLE to boards
which have the respective files. The only exception: EPIA-M700 doesn't
select ACPI, as it doesn't have dsdt.asl. Added a comment that the user
is supposed to run the 'get_dsdt' script and edit Kconfig afterwards.
- Fix minor warning/error in
src/mainboard/msi/ms9652_fam10/acpi_tables.c,
now that the file is actually used.
- msi/ms9652_fam10: use #include instead of Include() as we usually do
now.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6027 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
"To enable configuration, the entry key 0x87 must be written to
the index port"
"
-o 4e 87
-o 4e 87 (enable configuration)
-o 4e aa (disable configuration)
"
This piece of text appears in most of the datasheet of fintek superio.
It doesnt say it quite clear, but it seems that the 0x87 should
be written twice. I tried on f81865, which is not in the coreboot tree
yet. If the 0x87 is only written once, you can only R/W the index/data
port once. All the subsequent RW will fail. Writing twice will be ok.
Plus, in the superiotool, the function enter_conf_mode_winbond_fintek_ite_8787
also write 8787.
The fintek superio chips seem to enable the UART automatically when the
power is on. So I didnt find it failed to access.
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6025 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This is Abuild and boot tested.
Signed-off-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6023 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This is Abuild and boot tested.
Signed-off-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6022 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Drop banner(), use printk()s instead.
- Uncomment a few printk()s, if a users doesn't want to see them he/she
can lower the debug level.
- Replace print_emerg() with printk(BIOS_EMERG) etc.
Also change 'Assymetirc' into 'Asymmetric', thanks to Idwer for spotting.
This is Abuild and boot tested.
Signed-off-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6021 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Drop commented out "config chip.h" and a duplicate link to a datasheet.
- F71805F -> F71805F/FG, to mention all variants.
- Use u8/u16/ etc. everywhere.
- Add a missing (C) line.
- Fix up a bunch of pnp_dev_info[] structs according to the datasheets.
- Fintek F71889: Drop res1/PNP_IO1 from KBC, there's no 0x62/0x63 register
pair on this Super I/O.
- Fintek F71863FG: This Super I/O _does_ have a keyboard/mouse LDN, add the
respective code in superio.c. Also: Add missing LDNs to f71863fg.h.
- i3100: Add some more comments and datasheet infos.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6020 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also:
- Improve a few code comments, fix typos, etc.
- Change a few more variable types to u8/u16/u32 etc.
- Make some very long lines fit into 80chars/line.
- Drop a huge duplicated comment, use "@see" to refer to the other one.
- Reduce nesting level a bit by restructuring some code chunks.
- s/Config.lb/devicetree.cb/ in a few places.
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6019 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Untested, but should work mostly (even though some TODOs remain).
Signed-off-by: Alec Ari <neotheuser@ymail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6017 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This is Abuild and boot tested.
Signed-off-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6016 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This is Abuild and boot tested.
Signed-off-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6015 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
and gx2/raminit.c.
This is Abuild and boot tested.
Signed-off-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6014 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
hang. Also need to set lane config to 0x00 for autonegotiation.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6013 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
variant. It also adds additional dev_find_device calls in k8t890_ctrl.c for
subfunctions 3 and 7.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6012 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also, change the GX2 boards to use it.
Add a processor speed setting function in human readable MHz and remove
the useless and broken PLLMSR settings (the processor speed was hardcoded
to 366MHz in pll_reset.c).
Signed-off-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6011 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also, add a copyright header to pll_reset.c.
Signed-off-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6009 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- via/epia-n/mptable.c
- intel/eagleheights/mptable.c (commented out anyway)
- asus/p2b-d/mptable.c
- asus/p2b-ds/mptable.c
Some files still incorrectly contain some smp_write_ioapic() lines from
the original mptable utility target (Supermicro P4DPE), which has one
IOAPIC in the southbridge (Intel ICH3-S), two IOAPICs contained in
the first P64H2, and two more in the second P64H2, i.e. 5 IOAPICs in total.
However, none of the boards where this chunk of code is present has
multiple IOAPICs (and even if they had, the PCI devices where those are
located would probably be different anyway), so drop the incorrect
mptable.c contents.
Also drop the lines from the mptable utility, so that future mptable.c files
don't incorrectly inherit any of this stuff.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Jonathan Kollasch <jakllsch@kollasch.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6006 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Add "select IOAPIC" in the board's Kconfig file.
- Set CONFIG_MAX_PHYSICAL_CPUS to 2 on the board. There are two
CPU sockets (Slot 1) and each CPU can only have one core, multi-core CPUs
didn't exist in that era (CONFIG_MAX_CPUS was set to 2 already).
- Drop useless/duplicated enable_lapic() call from ASUS P2B-DS's romstage.c,
that function is always called if either CONFIG_SMP and/or CONFIG_IOAPIC
are set.
- Rework ASUS P2B-DS mptable.c to fix a number of things:
- Convert it to use mptable_write_buses() as all mptable.c files should do.
- Fix incorrect IOAPICID (it's 0x11 for the external 82093AA IOAPIC).
- Fix a bunch of hardcoded bus IDs, remove incorrect entries, etc.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6004 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Add enable_intel_82093aa_ioapic() which enables IOAPIC usage in the
Intel 82371EB southbridge (sets the proper chip-select) and sets an
IOAPIC ID.
- We only call enable_intel_82093aa_ioapic() if a board does "select IOAPIC"
as on 82371EB-based boards the IOAPIC is an external chip (not integrated
in the southbridge) and it's only populated on multi-CPU boards.
That is, we cannot unconditionally enable it, only on SMP-capable boards.
- Due to the reason explained above, remove "select IOAPIC" from
src/southbridge/intel/i82371eb/Kconfig, and add it to
src/mainboard/asus/p2b-d/Kconfig.
- Also set CONFIG_MAX_PHYSICAL_CPUS to 2 on ASUS P2B-D. There are two
CPU sockets (Slot 1) and each CPU can only have one core, multi-core CPUs
didn't exist in that era (CONFIG_MAX_CPUS was set to 2 already).
- Drop useless/duplicated enable_lapic() call from ASUS P2B-D's romstage.c,
that function is always called if either CONFIG_SMP and/or CONFIG_IOAPIC
are set.
- Rework ASUS P2B-D mptable.c to fix a number of things:
- Convert it to use mptable_write_buses() as all mptable.c files should do.
- Fix incorrect IOAPICID (it's 0x11 for the external 82093AA IOAPIC).
- Fix a bunch of hardcoded bus IDs, remove incorrect entries, etc.
This is build-tested on ASUS P2B-D, and also boot-tested successfully there.
On Linux I now get two entries in /proc/cpuinfo (where only one appeared
before this patch), i.e. both populated CPUs are found.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5998 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
boards using ck804_early_setup.c that select CK804_USE_NIC.
Signed-off-by: Jonathan Kollasch <jakllsch@kollasch.net>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5996 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Additionally, make the second SMBus more accessible in romstage.
Signed-off-by: Jonathan Kollasch <jakllsch@kollasch.net>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5994 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also, make them all fit in 80chars/column, fix some whitespace issues
and also some typos I noticed.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5993 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
local ints. This is wrong in most coreboot mptables, probably all
generated by util/mptable/mptable.c.
After fixing this now XP can boot in MPS mode on my M2V.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5992 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Jonathan Kollasch <jakllsch@kollasch.net>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5991 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Right now, it breaks the build of bootblock enabled boards
with that chipset.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5990 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5989 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Drop sig[], oem[], and productid[] fields in all mptable.c files, no
longer needed. The sig[] is always the same ("PCMP"), the oem[] is
currently also always the same ("COREBOOT"), and productid is being
passed into mptable_init() directly as string now.
- LAPIC_ADDR is passed in as parameter, too. While at the moment it's
always the same value that is passed in, the LAPIC base address could
also be relocated theoretically, so keep it as parameter for now.
- Fix a few productid entries, they were (partially) incorrect:
- DK8S2 (was "DK8X", copypaste)
- 939A785GMH (was "MAHOGANY", copypaste)
- X6DHE-G (was "X6DHE", incomplete board name)
- H8DME-2 (was "H8DMR", copypaste)
- H8QME-2+ (was "H8QME", incomplete board name)
- X6DHE-G2 (was "X6DHE", incomplete board name)
- X6DHR-iG2 (was "X6DHR-iG", incomplete board name)
- GA-M57SLI-S4 (was "M57SLI", incomplete board name)
- KINO-780AM2 (was "KINO", incomplete board name)
- DL145 G1 (was "DL145G1", small fix as per vendor website)
- DL145 G3 (was "TREX", wrong board name)
- DL165 G6 (was "HP DL165 G6", drop vendor)
- S2912 (was "S2895", copypaste)
- VT8454c (was "VIA VT8454C", drop vendor, lower-case "c")
- EPIA-N (was "P4DPE", copypaste)
- pc2500e (was "PC2500", incorrect name)
- S1850 (was "S2850", copy-paste)
- MS-7135 (was "MS7135")
- MS-9282 (was "MS9282")
- MS-9185 (was "MS9185")
- MS-9652 (was "K9ND MS-9652")
- Ultra 40 (was "ultra40")
- E326 (was "E325", copypaste)
- M4A785-M (was "TILAPIA", copypaste)
- P2B-D (was "ASUS P2B-D", drop vendor)
- P2B-DS (was "ASUS P2B-DS", drop vendor)
- Adapt the mptable utility to use mptable_init() too.
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5987 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
FADT revision inconsistent with length.
Revision: 0x1
Length: 0xf4
Expected Length: 0x74
Change the FADT revision from 1 to 3 to match its length and prevent the Windows checked build assert.
Signed-off-by: Scott Duplichan <scott@notabs.org>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5985 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
for 256 buses, even if fewer are configured. This patch lets msr
c0010058 programming use the configured bus count, CONFIG_MMCONF_BUS_NUMBER.
Signed-off-by: Scott Duplichan <scott@notabs.org>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5976 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This is consistent with the device tree and the chip actually on the board.
Trivial.
Signed-off-by: Jonathan Kollasch <jakllsch@kollasch.net>
Acked-by: Jonathan Kollasch <jakllsch@kollasch.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5974 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
#ifdef DEADCODE out smbus_write_byte() and smbus_write_block() as
they are static and nothing uses them or are incompletely implemented.
Signed-off-by: Jonathan Kollasch <jakllsch@kollasch.net>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5972 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also, update the board that uses this socket to match.
Signed-off-by: Jonathan Kollasch <jakllsch@kollasch.net>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5969 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
currently restricted to recent model AMD processors, though it could be applied to others after successful testing.
Signed-off-by: Scott Duplichan <scott@notabs.org>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5967 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
is sometimes logged. The reason is that the AP first sets a completion value
such as 0x13, which is what function wait_cpu_state() is waiting for. Then a
short time later, the AP calls function init_fidvid_ap(). This function sets
a completion value of 01. When logging is off, wait_cpu_state is fast enough
to see the initial completion value for each of the APs. But with logging
enabled, one or more APs may go on to complete function init_fidvid_ap, which
sets the completion value to 01. While mostly harmless, the timeout does
increase boot time. This patch eliminates the timeout by making function
wait_cpu_state recognize 01 as an additional valid AP completion value.
Signed-off-by: Scott Duplichan <scott@notabs.org>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5966 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
It affects only systems booting from SPI flash, not those booting from
LPC flash. By default, the SB700 reads dwords from the SPI flash chip.
Setting PrefetchEnSPIFromHost causes the SB700 to read entire cache
lines from the flash chip.
Signed-off-by: Scott Duplichan <scott@notabs.org>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5965 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This also has an additional benefit:
I was running "sh update-microcodes.sh" previously which broke with
update-microcodes.sh: 102: Bad substitution
due to the script requiring /bin/bash instead of /bin/sh (uses bash-specific
stuff). Running "bash update-microcodes.sh" works fine.
Making the script executable in svn reduces the likelyhood of people
running the script with differing shells that may not work.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5963 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Whitespace and indentation fixes in various places.
- Fix various typos.
- Use u8, u16 etc. everywhere.
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5962 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
They now have their own home at cpu/intel/model_65x.
Signed-off-by: Keith Hui <buurin@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5960 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
to zero, so for boards with RS780 not on CPU's HT chain 0, the function will
mis-configure the MMIO dst-link routing, and the following enable_pcie_bar3()
function will hang when it visits the MMIO.
The following patch fixes the problem, and is tested on a K8 board with RS780
on HT chain 1.
Signed-off-by: Liu Tao <liutao1980@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5959 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Fix that to read the register from the chain where the SB chip is on.
Signed-off-by: Liu Tao <liutao1980@gmail.com>
Acked-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5958 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Fix incorrect argument names for @param entries.
- Add missing @param and @return entries, partly as TODOs.
- s/@returns/@return/, that's a typo.
- Small whitespace fixes while I'm at it.
- Drop useless @brief commands, they just clutter the comments and make them
harder to read. Doxygen has an option to always use the first sentence
of a Doxygen-comment as @brief automatically (should be on per default).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5955 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
abuild-tested. I have no Deschutes CPUs to boot test this with.
Signed-off-by: Keith Hui <buurin@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5954 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This CAR implementation hardcodes the Cache-as-RAM base address to:
0xd0000 - CacheSize
so the DCACHE_RAM_BASE is never actually used for this implementation
and these sockets.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5953 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This is pretty much the same mechanism as in r5929.
- Use 'romstage-y' to turn i82801ax_early_smbus.c and i82801bx_early_smbus.c
into distinct compilation units, and don't #include the files anymore
in romstage.c files.
- Ditto for northbridge/intel/i82810/raminit.c, and
northbridge/intel/i82810/debug.c.
- Add various header files which are now needed, drop unused includes.
- Make functions that need to be visible non-static.
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5951 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Drop "select ROMCC" from the boards, as well as early_mtrr stuff.
- Add "select CACHE_AS_RAM" to socket_PGA370/Kconfig, as well as the
usual DCACHE_RAM_BASE and DCACHE_RAM_SIZE variables.
- In socket_PGA370/Makefile.inc add:
cpu_incs += $(src)/cpu/intel/car/cache_as_ram.inc
- Other smaller related fixes.
Abuild-tested and boot-tested on MSI MS-6178.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5949 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Some mainboards need to disable the power button to avoid turning off
right after being turned on, while other boards ship with a jumper over
the power button and should allow the user to configure the behavior.
This adds infrastructure in the form of four mutually exclusive options
which can be selected in a mainboard Kconfig (power button forced on/off,
and user-controllable with default on/off) and one result bool which
source code can test. (Enable the button or not.)
The options have been implemented in CS5536 code and for all mainboards
which select SOUTHBRIDGE_AMD_CS5536, but should be used also by other
chipsets where applicable. Note that if chipset code uses the result
bool ENABLE_POWER_BUTTON, then every board using that chipset must
select one out of the four control options in order to build.
All touched boards should have unchanged behavior, except
pcengines/alix1c, traverse/geos and lippert/hurricane-lx where the
power button can now be configured by the user.
Build tested for alix1c, alix2d, hurricane-lx and wyse-s50. Confirmed
to work as advertised on alix1c both with button enabled and disabled.
Includes additional traverse/geos changes from Nathan and
lippert/hurricane-lx changes from Jens to correctly use the new
feature on those boards.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Aurelien Guillaume <aurelien@iwi.me>
Acked-by: Nils Jacobs <njacobs8@hetnet.nl>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5948 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
I could no longer boot my P3B-F with my Tualeron and r5938. Dies with
"unknown CPU". I believe it will happen with any Slot 1 440BX boards
that supports model_6bx CPUs.
I need to make the change below to make it work. abuild tested. Boot
tested on P2B-LS and P3B-F.
Signed-off-by: Keith Hui <buurin@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5945 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This is in preparation of further i810 fixes and switching it to CAR.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5944 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
As both ioapic.h and acpi.h define a macro named "NMI", rename one
of them (NMI -> NMIType in acpi.h).
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5943 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Macros for the register addresses for the MTRR MSRs are already defined
in include/cpu/x86/car.h. This patch uses those macros instead of
creating a second instance of that same data.
I also added a few macros to the amd mtrr.h to make the MSR naming more
consistent.
Signed-off-by: Warren Turkal <wt@penguintechs.org>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5942 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The file is actually just including a bunch of assembly. The build rule
for bootblock.c even states that the file will be "assembler-with-cpp."
Signed-off-by: Warren Turkal <wt@penguintechs.org>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5941 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
BTW, embed the always-the-same string instead of referencing it through "%s".
Do the same for i82371EB while we're at it.
Signed-off-by: Sylvain Hitier <sylvain.hitier@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5940 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Drop all non-ICH2 "struct pci_driver" entries from all files.
- Kconfig: Add missing USE_WATCHDOG_ON_BOOT.
- Drop i82801bx_sata.c and i82801bx_usb_ehci.c, ICH2 doesn't have SATA/EHCI.
- Simplify lots of code, getting rid of i82801xx remainders.
- Use u8 et al (instead of uint8_t) in a few more places.
- Use #defines from header files where possible.
- Various other fixes and updates.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5938 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The following functions are moved to devices/device_util.c:
- ram_resource()
- tolm_test()
- find_pci_tolm()
There are only two tolm_test() / find_pci_tolm() which differ from the
defaults, one of them can easily be eliminated in a follow-up patch,
maybe even both, but for now keep it simple and only eliminate the majority.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5937 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Following patch enables UDMA on ALL IDE devices. The current code enables it only for primary master, which causes my DVD drive to fail under windows install
and even after hard reset in linux (DMA seems lockup).
The fix should not have any influence for Linux because the IDE driver will
correctly reprogram this bit.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5933 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
primary / secondary IDE channel with SATA (in IDE mode).
The bug was that setup was done in wrong device.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5932 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
and even after hard reset in linux (DMA seems lockup).
The fix should not have any influence for Linux because the IDE driver will
correctly reprogram this bit.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5931 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Use 'romstage-y' to turn i82371eb_early_pm.c and i82371eb_early_smbus.c
into distinct compilation units, and don't #include the files anymore
in romstage.c files.
- Ditto for lib/debug.c, northbridge/intel/i440bx/raminit.c, and
northbridge/intel/i440bx/debug.c.
- Add various header files which are now needed.
- Make functions that need to be visible non-static.
- Drop a remaining "select ROMCC" from a 4440BX board.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Idwer Vollering <vidwer@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5929 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Nothing ever calls the functions in these files, and we already have
i82801ax_watchdog.c and i82801bx_watchdog.c which basically do the same
_and_ are hooked up correctly in the Makefile.inc and via the
USE_WATCHDOG_ON_BOOT mechanism.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5926 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Remove left-overs from more generic code in i82801xx times, and fix
register names as needed.
- Simplify IDE init code (and save some ROM space too).
- Simplify PIRQ code.
- Use u8 et al instead of uint8_t everywhere.
- Random other fixes.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5925 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Fix incorrect #includes, add missing ones.
- Drop unused do_smbus_write_block() and smbus_wait_until_blk_done().
- Pass smbus_io_base to all functions as the other ICH implementations do.
- Random other fixes which are required to make it build.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5924 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
bit in the AMD processor 'MMIO Limit Address Register'.
I suspect it is because of a typo where 0x80 was entered
as 0x8. If 0x80 is used, then the strap configuration
register accesses become non-posted, which is how the
Shiner reference BIOS does it.
Signed-off-by: Scott Duplichan <scott@notabs.org>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5919 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also:
Unfortunately Intel 440BX + 82371AB/EB/MB boards can have their ISA device
on various PCI bus:device.function locations.
Examples we encountered: 00:07.0, 00:04.0, or 00:14.0.
Thus, instead of hardcoding PCI bus:device.function numbers such as
PCI_DEV(0, 7, 0), we now simply find the ISA device via PCI IDs, which
works the same on all boards.
As an additional benefit this patch also gets rid of one .c file include
in romstage.c.
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5918 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Add "select CACHE_AS_RAM" in src/cpu/intel/slot_1/Kconfig.
- Add the following in src/cpu/intel/slot_1/Makefile.inc:
cpu_incs += $(src)/cpu/intel/car/cache_as_ram.inc
- Remove "select ROMCC" from all 440BX board Kconfig files.
- Drop all early_mtrr_init() calls, that's done by CAR code now.
Various small fixes were needed to make it build:
- Drop do_smbus_recv_byte(), do_smbus_send_byte(), do_smbus_write_byte(),
those were never called anyways.
- Remove the "static" from the main() functions in romstage.c files.
- Always call dump_spd_registers() from the 440BX debug.c, but use
"#if CONFIG_DEBUG_RAM_SETUP" to only have that code if RAM debugging
is enabled in menuconfig.
- Drop all "lib/ramtest.c" #includes and ram_check() calls (even if
commented out) from romstage.c's, as we've done for most other boards.
- Add missing #includes or prototypes. Some of the prototypes will be
removed later when we get rid of the #include'd .c files.
Abuild-tested for all boards, and boot-tested on A-Trend ATC-6220.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5917 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- move EHCI_BAR and EHCI_DEBUG_OFFSET to Kconfig to be set by USB debug port enabled southbridges
- drop USB debug code includes from romstage.cs and use romstage-srcs in the build system instead
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5911 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Remove many more .c-includes from i945 based boards.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5910 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Add links to the respective Intel specification updates or manuals where
the IDs are listed. Mention the possible core steppings of each CPU ID.
There are duplicate IDs in model_6xx and model_68x for now, not sure if
those should be eliminated, but there were already duplicates before this
patch, so that's probably an extra issue to look into.
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5909 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The AMD SB700 allows changing the physical USB port to be used as
USB Debug Port, implement support for this.
Also, fix incorrect PCI device of the SB700 EHCI device. Actually, the
SB700 has _two_ EHCI devices (D18:F2 and D19:F2), but for now we only use
D18:F2. Our generic USBDEBUG code cannot handle multiple EHCI PCI devices
currently, AFAICS.
Hook up all SB700 boards to the CONFIG_USBDEBUG_DEFAULT_PORT facility.
Untested, but should work.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5907 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
It cannot be changed via software according to the datasheet, whereas
this is indeed possible on AMD SB700. I tested using the SB700 mechanism
on SB600 but it didn't work, so I suspect the datasheet is indeed correct.
Thus, don't show the kconfig option for selecting the physical USB port
on the AMD SB600 southbridge.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5906 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
All these boards define QRANK_DIMM_SUPPORT anyway,
which is probably what was meant.
Signed-off-by: Jonathan Kollasch <jakllsch@kollasch.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5905 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This makes the CAR implementations a lot more readable, shorter and
easier to follow, and also reduces the amount of uselessly duplicated code.
For example there are more than 12 open-coded "enable cache" instances
spread all over the place (and 12 "disable cache" ones), multiple
"enable mtrr", "save BIST", "restore BIST", etc. etc.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5902 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This is abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5901 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Makefile:261: warning: overriding commands for target `coreboot-builds/a-trend_atc-6220/lib/lzma.ramstage.o'
Makefile:261: warning: ignoring old commands for target `coreboot-builds/a-trend_atc-6220/lib/lzma.ramstage.o'
lzma.c is already included unconditionally in the same file.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5900 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
rename it slightly, make it visible only on relevant northbridges,
drop it entirely from via boards (as they seem to have picked it
up from AMD code without using it themselves), and make it
default to false for all boards.
Some romstages used to set this to "true" (ie. "print debug output"),
but I didn't follow up on it in Kconfig - if you need it to debug CAR,
enable it yourself.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5898 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5896 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This is needed for Gentoo gcc-4.1.2 to build the i945 code. A warning is
thrown because the comparison in the last hunk is between u16 and -1 and
can never be true.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5895 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
copy&paste, without actually being used.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5894 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Both chipsets use the src/northbridge/intel/i945 code but that code
needs to know which chipset is actually used. Having separate
NORTHBRIDGE_ options allows the I945GC/I945GM choice to be removed
since code can test the NORTHBRIDGE_ option directly.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5893 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5891 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Use some more #defines instead of hard-coding values.
- Merge multiple movl/orl or movl/andl lines into one where possible.
- Add some TODOs in places which seem to have either an incorrect
code or incorrect comment.
- Fix typos: s/for/from/, s/BSC/BSP/, s/size/carsize/.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5890 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also, whitespace fixes, consistency fixes, and drop some of the less
useful comments.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5888 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Replace $0x200 with $MTRRphysBase_MSR(0) etc. Also, move some #ifdef stuff
a little bit around (should not affect any functionality) to make the
Intel/AMD/VIA CAR implementations more similar and easier to compare.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5887 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
at the same time let the user specify sources instead
of object files:
- objs becomes ramstage-srcs
- initobjs becomes romstage-srcs
- driver becomes driver-srcs
- smmobj becomes smm-srcs
The user servicable parts are named accordingly:
ramstage-y, romstage-y, driver-y, smm-y
Also, the object file names are properly renamed now, using
.ramstage.o, .romstage.o, .driver.o, .smm.o suffixes consistently.
Remove stubbed out via/epia-m700 dsdt/ssdt files - they didn't
easily fit in the build system and aren't useful anyway.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coreystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5886 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
For the a number of the socket 940 based machines, I collapsed their CAR
configurations into the socket config.
However, I have kept a number of overrides in place for the following
machines:
* broadcom/blast
* ibm/e32{5,6}
* newisys/khepri
* sunw/ultra40
* tyan/s488{0,2}
These machines used different setting than the defaults for socket 940
systems.
Signed-off-by: Warren Turkal <wt@penguintechs.org>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5883 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This change is somewhat dangerous as it enables CAR for some boards that
it was not enabled for before.
Signed-off-by: Warren Turkal <wt@penguintechs.org>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5882 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The fill_processor_name() function was duplicated in multiple
model_*_init.c files, move it into a new src/cpu/x86/name
directory.
The strcpy() function was also duplicated multiple times, move it
to <string.h> where we already have similar functions.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5879 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
We don't surround the <usbdebug.h> #include with those checks in other
places either. Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5876 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
configs. I just moved it the the CPU that they all use.
Signed-off-by: Warren Turkal <wt@penguintechs.org>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5871 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
mainboard that uses it.
Signed-off-by: Warren Turkal <wt@penguintechs.org>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5868 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Now we only need to clean out the FAM10 stack mess and we're good to go with a
uniform RAMBASE.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5864 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
USB port for use as Debug Port (on chipsets which support that).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5860 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
few more code comments to src/cpu/x86/*.inc files.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5859 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
that component rather than the mainboard.
The intel/d810e2cb is the only board using the i82801bx southbridge.
Signed-off-by: Warren Turkal <wt@penguintechs.org>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5856 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Most of the mainboards with i82801gx SBs seem to use the
HAVE_HARD_RESET, which is already selected in the i82801gx SB config.
Removing it from some of those boards should be a functional no-op.
Signed-off-by: Warren Turkal <wt@penguintechs.org>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5855 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
All Intel CPU models appear to be identified with the form
INTEL_CPU_MODEL_xxxxx. I haved changed the Atom to fit this normal form.
A side effect is that the CPU doesn't need to be listed on the boards
that support it since the socket identifies the CPUs it supports.
Signed-off-by: Warren Turkal <wt@penguintechs.org>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5853 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
is selected that uses a chipset which actually has that functionality _and_
we have code to initialize the Debug Port in coreboot (for that chipset).
Also, remove the duplicate list of PCI IDs and just link to the wiki page at:
http://www.coreboot.org/EHCI_Debug_Port
The list is now less useful in the kconfig help as this option will only
appear for those boards where it's actually supported.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5848 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Use PCI_COMMAND and PCI_COMMAND_MEMORY from pci_def.h instead of
hardcoding their values.
- SB600/SB700: Drop useless/unused SB600_DEVN_BASE and SB700_DEVN_BASE.
- ICH7: Drop unused EHCI_CONFIG_FLAG and EHCI_PORTSC.
- s/uint32_t/u32/.
- Cosmetics, whitespace, coding style fixes and added code comments.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5847 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5846 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Build-tested using abuild.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5844 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Some boards still used the old DEBUG_RAM_SETUP (without _CONFIG prefix).
Also, consistently use "#if CONFIG_DEBUG_RAM_SETUP" (not #ifdef) as we do
elsewhere.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5843 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Drop unused DBGP_DEFAULT #defines on boards with chipsets where no
USB Debug Port support is implemented anyway (at the moment, at least):
- hp/dl145_g3
- hp/dl165_g6_fam10
- ICH7: Move unrelated code out of set_debug_port(). All ICH southbridges
with Debug Port hardcode the physical USB port used as Debug Port to 1.
In other words, this port is not user-configurable (as seems to be
the case on NVIDIA MCP55). For now we keep the 'port' parameter in order
to not change the API, this might be fixed differently later.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5842 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
wonder why variables in .data or .bss (both somewhere in ROM space)
are wrong.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5841 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Three CAR implementations on Intel CPUs include <cpu/amd/mtrr.h>, which
is obviously wrong, so drop the #includes. None of their #defines are used
in the Intel code.
Build-tested with two of the affected boards.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5840 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
statement to those files that actually need it. This significantly
reduces the number of dependencies, so it's no longer extremely ugly to
specify them manually (see the src/pc80/Makefile.inc portion)
- Add double include guards around option_table.h defines
- Also, drop the AMD DBM690T work around for the issue
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5838 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also fixes random whitespace issues, typos, etc.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5837 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
the device tree, instead of using hardcoded values.
If this changes behaviour, this is either
- a bug in mptable_write_buses(), or
- a bug in the old mptable or device config, that is
they were inconsistent.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5835 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5834 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Without a (currently) dummy set_debug_port() function the build fails,
this may or may not be fixed differently in the future.
Manually build-tested on all SB600/SB700 boards, and tested on hardware on
one SB600 board I own, works fine.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5833 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
another recent change into account.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5832 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Original patch was
Signed-off-by: Arne Georg Gleditsch <arne.gleditsch@numascale.com>
Updates to accomodate changes in coreboot are
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5831 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Add missing license headers, or missing (C) lines to various files.
(most are from AMD / Yinghai Lu, based on svn logs)
- src/include/ehci.h was taken from the Linux kernel. Updating it to
the latest version from git HEAD while I'm at it (build-tested with
one board). It also sports some new EHCI 1.1 addendum #defines which
we may or may not need.
This new file also already has a proper GPL header.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5828 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
used for source level debug.
Signed-off-by: Marc Jones <marcj303@gmail.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5827 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The 'delay' variable shadows the global 'delay()' function, yielding
this compiler warning/error:
src/pc80/../lib/usbdebug.c: In function `ehci_reset_port':
src/pc80/../lib/usbdebug.c:281: error: declaration of `delay' shadows a global declaration
src/lib/delay.c:9: error: shadowed declaration is here
This fixes the issue by renaming the 'delay' variable to 'delay_ms'.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5826 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
consits of weak function which always exists (with defaults) and a possibility to
override this with normal function in main.c. This is the other way of
doing that and not using the devictree.cb.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5825 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
After we splitted up the old i82801xx driver which was supposed to support
multiple generations of ICH* chipsets, some of the generified code
is now obsolete in i82801ax which should only cover ICH/ICH0 and none of
the later ICH* generations.
Hence:
- Drop "struct pci_driver" entries for chipsets other than ICH/ICH0.
- Drop drivers for hardware that is not present on ICH/ICH0: NIC, SATA, EHCI.
- Drop PIRQE-PIRQH #defines and code, not available on this chipset.
- Simplify some parts of the code (more will follow).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5824 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5821 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Resolves a number of TODOs items within, and clarified a number of other TODOs.
Change register_values[] from long to u8 (byte). For what we are doing
this is sufficient and makes it only 1/4 the size.
Remove a hard-coding of SDRAMC register that is redundant and now
incorrect, now that SDRAMC is conditioned on SDRAMPWR_4DIMM Kconfig
and set through register_values[].
This fixes all boards with 3 DIMM slots (e.g. ASUS P2B, A-Trend ATC-6220).
RPS registers are now set in runtime code; remove it from
register_values[] table.
Bring DUMPNORTH() back. The code it refers to is still there.
Move #define of NB up so the DUMPNORTH() macro can use it.
Signed-off-by: Keith Hui <buurin@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5820 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
On this board all reads from SPD return 0xff by default, there's a custom
GPIO fiddling needed to enable access to the SPD SMBus offsets at
0x50-0x53. While coreboot actually sort of booted sometimes before r5193,
that was just sheer luck as the RAM init was hardcoded in certain ways.
Since the proper, more heavily SPD-based RAM init the brokenness of the
ASUS P3B-F RAM init was becoming visible.
This patch uses GPIOs to enable access to the SPD SMBus offsets,
and resets the GPIOs again after RAM init (this is needed to allow for
lm-sensors to work, for example).
Tested successfully on hardware.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Idwer Vollering <vidwer@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5819 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Root cause: After function STOP_CAR_AND_CPU disables cache as
ram, the cache as ram stack can no longer be used. Called
functions must be inlined to avoid stack usage. Also, the
compiler must keep local variables register based and not
allocated them from the stack. With gcc 4.5.0, some functions
declared as inline are not being inlined. This patch forces
these functions to always be inlined by adding the qualifier
__attribute__((always_inline)) to their declaration.
Signed-off-by: Scott Duplichan <scott@notabs.org>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5818 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Arne Georg Gleditsch <arne.gleditsch@numascale.com>
Acked-by: Scott Duplichan <scott@notabs.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5817 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
newer Phenom II.
Signed-off-by: Marc Jones <marcj303@gmail.com>
Acked-by: Paul Menzel <paulepanter@users.sourceforge.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5815 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
of 'Erratum 343 for AMD Fam10h CPUs' (rev 4345). The original code
sets msr c001_102a bit 3 when bit 35 was intended.
Signed-off-by: Scott Duplichan <scott@notabs.org>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5814 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Zheng Bao