All current implementations of ramstage_cache_invalid() were just
resetting the system based on the RESET_ON_INVALID_RAMSTAGE_CACHE
Kconfig option. Move that behavior to a single implementation
within prog_loaders.c which removes duplication.
Change-Id: I67aae73f9e1305732f90d947fe57c5aaf66ada9e
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/17184
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
ramstage_cache_invalid which was added in
I83fe76957c061f20e9afb308e55923806fda4f93 (review.coreboot.org/#/c/17112)
requires hard_reset to be defined in postcar stage.
BUG=None
BRANCH=None
TEST=Compiles successfully for reef.
Change-Id: I283277c373259e0e2dfe72e3c889ceea012544f2
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17182
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
While using '3' is fine for the standard gpe0 for skylake, I want
to make sure anyone that copies this code doesn't tweak GPE0_REG_MAX
without the hard coded index. If that does happen now things will
still work, but it may just not match the hardware proper.
BUG=chrome-os-partner:58666
Change-Id: I434b9a765a0a2f263490bb2b4ecb3635292d46c9
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/17160
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Add a GPIO macro that allows a pin to be routed to the APIC with
the input inverted. This allows a normal interrupt to get used as
a GPE during firmware and still be used as a perhiperal interrupt
in the kernel.
BUG=chrome-os-partner:58666
TEST=boot en eve and use TPM IRQ in firmware and OS
Change-Id: I77f727f749fdd5281ff595a9237fe1e634daba96
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/17176
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Add the necessary infrastructure to support eSPI SMI events,
and a mainboard handler to pass control to the EC.
BUG=chrome-os-partner:58666
TEST=tested on eve board with eSPI enabled, verified that lid
close event from the EC during firmware will result in an SMI
and shut down the system.
Change-Id: I6367e233e070a8fca053a7bdd2534c0578d15d12
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/17134
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Export the pmc_gpe_init() function from pmc.c to pmutil.c
so it can be used in bootblock, and then call it from there
to initialize any GPEs for use in firmware.
BUG=chrome-os-partner:58666
TEST=test working GPE as TPM interrupt on skylake board
Change-Id: I6b4f7d0aa689db42dc455075f84ab5694e8c9661
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/17135
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Add the SOC definition for acpi_get_gpe() so it can be used
by the I2C TPM driver. Also add the I2C support code to
verstage so it can get used by vboot.
BUG=chrome-os-partner:58666
TEST=boot with I2C TPM on skylake board
Change-Id: I553f00a6ec25955ecc18a7616d9c3e1e7cbbb8ca
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/17136
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
The Deep S3 state will lose a lot of register contents that we
used to rely on for determining wake source.
In order to make use of this override the enable bit for wake
sources that are enabled for Deep S3 in devicetree.cb.
BUG=chrome-os-partner:58666
TEST=check for _SWS reporting wake source on S3 resume on skylake
Change-Id: If5113d6890f6cbecc32f92af67a29952266fe0ac
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/17137
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Remove the FADT from the individual mainboards and select and
use COMMON_FADT in the SOC instead. Set the ACPI revision to 5.
Change-Id: Ieb87c467c71bc125f80c7d941486c2fbc9cd4020
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/17138
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Three things are required to enable wake-on-usb:
1. 5V to USB ports should be enabled in S3.
2. ASL file needs to have appropriate wake bit set.
3. XHCI controller should have the wake on attach/detach bit set for the
corresponding port in PORTSCN register.
Only part missing was #3.
This CL adds support to allow mainboard to define a bitmap in
devicetree corresponding to the ports that it wants to enable
wake-on-usb feature. Based on the bitmap, wake on attach/detach bits in
PORTSCN would be set by xhci.asl for the appropriate ports.
BUG=chrome-os-partner:58734
BRANCH=None
TEST=Verified that with port 5 enabled, chell wakes up from S3 on usb
attach/detach.
Change-Id: I40a22a450e52f74a0ab93ebb8170555d834ebdaf
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17056
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Use intel common infrastructure to enable support for write-protecting
SPI flash range. Also, enable this protection for RW_MRC_CACHE.
BUG=chrome-os-partner:58896
TEST=Verified that write to RW_MRC_CACHE fails in OS using
"flashrom -p host -i RW_MRC_CACHE -w /tmp/test.bin"
Change-Id: I35df12bc295d141e314ec2cb092d904842432394
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17117
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Write-protect SPI flash range provided by caller by using a free Flash
Protected Range (FPR) register. This expects SoC to define a callback
for providing information about the first FPR register address and
maximum number of FPRs supported.
BUG=chrome-os-partner:58896
Change-Id: I4e34ede8784e5587a5e08ffa10e20d2d14e20add
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17115
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
We found sdram may fail in pctl_cfg(), so we check the status in this
function. If it exceeds 100ms still in this function, we will restart
the system. We also found there are rare chances DDR training fails,
so also restart system in that case.
BUG=chrome-os-partner:57988
BRANCH=None
TEST=coreboot resets on failure and eventually the system comes up
Change-Id: Icc0688da028a8f4f81eafe36bbaa79fdf2bcea74
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 89e45f8352f62e19a203316330aba14ccc5c8b11
Original-Change-Id: If4e78983abcfdfe1e0e26847448d86169e598700
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/397439
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/17045
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Implement GPIO ACPI AML generating functions that can be called by
coreboot drivers to generate GPIO manipulation code in AML. Following
functions are implemented:
1. acpigen_soc_read_rx_gpio
2. acpigen_soc_get_tx_gpio
3. acpigen_soc_set_tx_gpio
4. acpigen_soc_clear_tx_gpio
BUG=chrome-os-partner:55988
Change-Id: I3d8695d73a1c43555032de90f14ee47ccee45559
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17082
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
This patch adds a Makefile rule for mvmap2315 to install a BDB and
bootblock code in the BOOTBLOCK region. The resulting BDB has a
header and data both signed by a RSA-4096 key.
BUG=chrome-os-partner:57889
BRANCH=none
TEST=emerge-rotor coreboot and examined the output binary. Booted
coreboot.rom.
Change-Id: I1e20a09b12f8f8ed4d095aa588e3eb930f359fc5
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://review.coreboot.org/16747
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
While we stub out free(), tools like coverity scan have no idea, and it
might change in the future. So free it.
Change-Id: I1d93a6f45b64445662daa95b51128140ad0a87e2
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Found-by: Coverity Scan #1260716
Reviewed-on: https://review.coreboot.org/17055
Tested-by: build bot (Jenkins)
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
This refactoring was already carried into RK3288 with commit 6911219
(edid: Add helper function to calculate bits-per-pixel dependent values)
but it seems that the code for RK3399 was copy&pasted from it too early
to pick this up. Fix that so that future Rockchip SoCs can copy&paste
the right thing.
Change-Id: I5050c58d18db38fffabc7666e67a622d4a828590
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/17050
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Skip FSP initiated core/MP init as it is implemented and initiated
in coreboot.
Add soc core init to set up the following feature MSRs:
1. C-states
2. IO/Mwait redirection
BUG=chrome-os-partner:56922
BRANCH=None
TEST= Check C-state functioning using 'powertop'. Check 0xE2 and
0xE4 MSR to verify IO/Mwait redirection.
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com>
Change-Id: I97c3d82f654be30a0d2d88cb68c8212af3d6f767
Reviewed-on: https://review.coreboot.org/16587
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch sets the package power limit (PL1) value in RAPL MSR
and disables MMIO register. Added configurable PL1 override
parameter to leverage full TDP capacity.
BUG=chrome-os-partner:56922
TEST=webGL performance(fps) not impacted before and after S3.
Change-Id: I34208048a6d4a127e9b1267d2df043cb2c46cf77
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Signed-off-by: Venkateswarlu Vinjamuri <venkateswarlu.v.vinjamuri@intel.com>
Reviewed-on: https://review.coreboot.org/16884
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
In FSP1.1 all the platform resets including global was handled
on its own without any intervention from coreboot.
In FSP2.0, any reset required will be notified to coreboot
and it is expected that coreboot will perform platform reset.
Hence, implement platform global reset hooks in coreboot. If Intel
ME is in non ERROR state then MEI message will able to perform
global reset else force global reset by writing 0x6 or 0xE to
0xCF9 port with PCH ETR3 register bit [20] set.
BUG=none
BRANCH=none
TEST=Verified platform global reset is working with MEI
message or writing to PCH ETR3.
Change-Id: I57e55caa6d20b15644bac686be8734d9652f21e5
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/16903
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
As per ME BWG, there are two mechanism to generate a Global
Reset (resets both host and Intel ME), one is through CF9h
IO write of 6h or Eh with "CF9h Global Reset" (CF9GR) bit set,
PMC PCI offset ACh[20]. Another is to issue the Global Reset
MEI message. Because any attempts to cause global reset without
synchronizing the two sides might cause unwanted side effects,
such as unwritten flash data that will get destroyed if the
host were to cause a global reset without informing Intel ME
firmware, the recommended method is to send a Global Reset MEI
message when the following conditions are met:
The PCH chipset firmware just needs to complete the Intel ME
Interface #1 initialization and check the Intel ME HFSTS state
if Intel ME is not in ERROR state and is accepting MEI commands
then firmware should be able to use Global Reset MEI message to
trigger global reset.
Furthermore, if Intel ME is in ERROR state, BIOS can use I/O 0xCF9
write of 0x06 or 0x0E command with PCH ETR3 register bit [20]
to perform the global reset.
BUG=none
BRANCH=none
TEST=Verified Global Reset MEI message is able to perform platform
global issue in ME good state.
Change-Id: If326a137eeadaa695668b76b84c510e12c546024
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/16902
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch programs and enables BAR for ME (bus:0/
device:0x16/function:0) device to have early ME communication.
BUG=none
BRANCH=none
TEST=Verified Global Reset MEI message can able to perform platform
global reset during romstage.
Change-Id: I99ce0ccd42610112a361a48ba31168c9feaa0332
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/17016
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
VBOOT_EC_SLOW_UPDATE should be selected if EC_GOOGLE_CHROMEEC is used as
building coreboot with Chrome OS support & without Chrome EC gives a
build error in coreboot.
Change-Id: I77eed0e1bdc1ba49381b72e21b0e18f573cadff0
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/17020
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The clearing of the PMC registers was not being called resulting
in state persisting across reboots. This state is queried and
events are added to the eventlog like 'RTC reset' events. However,
the RTC reset event is a one time thing so it should only be logged
once. Without the clearing of the state the event was logged on
every boot.
BUG=chrome-os-partner:58496
Change-Id: I60aa7102977c2b1775ab8c54d1c147737d2af5e2
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/17027
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
When timestamp is enabled, the system hangs because the timestamp data
is not yet available. Add a temporary work around that starts the
timestamp after the FspInit() making this data available.
Verified on Intel Camelback Mountain CRB and ensured that system can
boot to payload with timpstamp feature enabled.
Change-Id: I59c4bb83ae7e166cceca34988d5a392e5a831afa
Signed-off-by: York Yang <york.yang@intel.com>
Reviewed-on: https://review.coreboot.org/16894
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
The enforced FSP 1.0 APIs call was used to work around an fsp1.0 driver
issue. As the issue has been addressed in fsp1.0 driver (Change 9780),
remove the enforced workaround. Otherwise will see error message
'FSP API NotifyPhase failed' in serial log.
Verified on Intel Camelback Mountain CRB and confirmed that the serial
log error message regarding the 'FSP API NotifyPhase failed' is gone.
Change-Id: Iafa1d22e2476769fd841a3ebaa1ab4f9713c6c39
Signed-off-by: York Yang <york.yang@intel.com>
Reviewed-on: https://review.coreboot.org/16892
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Though we don't use Type-C PHY to support USB3 in firmware,
we still need to initialize the Type-C PHY, and make sure
the power state of pipe is always fixed to U2/P2. After
this, we can force USB3 controller to work in USB2 only
mode.
BRANCH=none
BUG=chrome-os-partner:56425
TEST=Go to recovery mode, plug a Type-C USB drive containing
chrome OS image into both ports in all orientations, check if
system can boot from USB.
Change-Id: I95bb96ff27d4fecafb7b2b9e9dc2839b5c132654
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 8ec98507845276119d8a9d5626934dedcb35f2dd
Original-Change-Id: Ie3654cd1c1cb76b62aa9b247879b60cbecee0155
Original-Signed-off-by: William wu <wulf@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/391412
Original-Commit-Ready: Julius Werner <jwerner@chromium.org>
Original-Tested-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16910
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Converged Security Engine (CSE) has a secure variable storage feature.
However, this storage is expected to be reset during S3 resume flow.
Since coreboot does not use secure storage feature, disable HECI2 reset
request. This saves appr. 130ms of resume time.
BUG=chrome-os-partner:56941
BRANCH=none
TEST=powerd_dbus_suspend; resume; check time with cbmem -t. Note
FspMemoryInit time is not significantly different from normal boot
time case.
Change-Id: I485a980369c6bd97c43b9e554d65ee89e84d8233
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/16870
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This patch enables stage cache to save ~40ms during S3 resume.
It saves ramstage in the stage cache and restores it on resume
so that ramstage does not have to reinitialize during the
resume flow. Stage cache functionality is added to postcar stage
since ramstage is called from postcar.
BUG=chrome-os-partner:56941
BRANCH=none
TEST=built for Reef and tested ramstage being cached
Change-Id: I1551fd0faca536bd8c8656f0a8ec7f900aae1f72
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/16833
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This reverts commit 28821dbb22.
(https://review.coreboot.org/16649)
This change causes the kernel to boot really slow. Maybe there is an
interrupt storm that prevents the kernel from making any
progress. Reverting until the proper kernel dependency is met.
BUG=chrome-os-partner:57364
BRANCH=None
TEST=Kernels boots to prompt fine on DVT.
Change-Id: I1c9913b4476a08303f9dd887b8631601c847dcf7
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: d7014ee1bb88df7a2d7f6b3dced797fef75b252d
Original-Change-Id: I061c0b03b43b516a190b370c04888e73a410fcf1
Original-Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/391233
Original-Reviewed-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/16881
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
CL:377541 was supposed to remove the big CPU cluster initialization from
rkclk_init() in the bootblock and move it to a more suitable place in
ramstage. Except that next to all the code cleanup I did in that patch,
I seem to have forgotten to actually remove that old code.
Big thanks to Nico for spotting that in the upstream coreboot review.
BRANCH=gru
BUG=chrome-os-partner:54906
TEST=Booted Kevin.
Change-Id: I09fe948b4587536802b42329b813177439e0804f
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 77f9eaf0446b22adfca79d0adf8a0ecfd93c0040
Original-Change-Id: I13dab208225b7e43ad864f2f3cf51b3c104acd4b
Original-Reported-by: Nico Huber <nico.h@gmx.de>
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/389236
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-on: https://review.coreboot.org/16769
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
This selects the rank to train before training is triggered. This is
to prevent any race conditions with the hardware.
BRANCH=none
BUG=chrome-os-partner:56940
TEST=stressapptest -M 1536 -s 1000
Change-Id: I892bace414cf4495619d41bdaea0c4e91c1e29b3
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 8f2dd6f52978a9e54ddd2688eb68fd237aabfe2d
Original-Change-Id: I4e7118d8509b59e391d0a254477b5390dfdd43a5
Original-Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/387907
Original-Commit-Ready: Douglas Anderson <dianders@chromium.org>
Original-Tested-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-by: 云平 汤 <typ@rock-chips.com>
Reviewed-on: https://review.coreboot.org/16768
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
There are two modifications in the driver:
1. Correctly set speeds based on DDR frequency.
Control the speeds in the predriver circuits to reduce power.
SPEED[1:0]
2'b00:less than 800Mbps(400MHz)
2b01 : 800Mbps(400MHz) to 1600Mbps(800MHz)
2b10 : 1600Mbsp(800MHz) to 2400Mbps(1200MHz)
2b11 : 3200Mbps and greater
2. Configure the number of cycles for the phy clock pll wait time after
locking, based on the DDR config file.
BRANCH=none
BUG=chrome-os-partner:56940
TEST=do memtester on kevin board, and pass
Change-Id: Iaf6da59c6c5c290867e0922a2a99de272f4c7bde
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 125cf8afac3a682d33896fe74a20ba1d498a3bd2
Original-Change-Id: Iabc17df37a701c4f052540c3c259f209a1db3c59
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/387428
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16722
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins)
In USB2 only mode, the Type-C PHY will be held in reset and
only the USB2 logic of the USB3 OTG controller and PHY will be
used over the USB2 pins on the Type-C connector to support Low,
Full and High-speed USB operation.
BRANCH=none
BUG=chrome-os-partner:56425
TEST=Go to recovery mode, plug a Type-C USB drive containing
chrome OS image into both ports in all orientations, check if
system can boot from USB.
Change-Id: Ic265c0c91c24f63b2f9c3106eb2bb277a589233b
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: a37ccc5b6019967483eac6b5a360d67bc3326e93
Original-Change-Id: I582f04f84eef447ff0ba691ce60e9461ed31cfad
Original-Signed-off-by: Liangfeng Wu <wulf@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/385837
Original-Commit-Ready: Julius Werner <jwerner@chromium.org>
Original-Tested-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16717
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
To improve sdram 800MHz and 933MHz stability, we
need to modify write leveling flow to get the
proper write leveling value.
BUG=chrome-os-partner:56940
BRANCH=none
TEST=Boot from kevin on 933MHz, and do stressapptest
Change-Id: I5b24c93d4a57917fb9af7e5e2a95d8423ccbaa7e
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: d84bf25b3e5de373c7913e6d534a810cb984b3fd
Original-Change-Id: I87efddf628c3683fcb85d6875e029cf3cbc482be
Original-Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Original-Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/384292
Original-Commit-Ready: Julius Werner <jwerner@chromium.org>
Original-Tested-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16716
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
We found that we may want to load some components of BL31 on the RK3399
into SRAM. As usual, these components may not overlap any coreboot
regions still in use at that time, as is already statically checked by
the check-ramstage-overlaps rule in Makefile.inc.
On RK3399, the only such regions are TTB and STACK. This patch moves the
TTB region back to the end of SRAM (right before STACK), so that a large
contiguous region of SRAM before that remains usable for BL31.
BRANCH=gru
BUG=None
TEST=Booted Kevin.
Change-Id: I1689d0280d79bad805fea5fc3759c2ae3ba24915
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 1d4c6c6f6cc0efe97d6962a81e309a1c040d1def
Original-Change-Id: I37c94f2460ef63aec4526caabe58f35ae851bab0
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/384635
Original-Reviewed-by: Simon Glass <sjg@google.com>
Reviewed-on: https://review.coreboot.org/16714
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
With a SPI clock above about 24MHz the APB cannot keep up when doing
individual byte transfers. Adjust the driver to use 16-bit reads when
it can, to remove this bottleneck.
Any transaction which involves writing bytes still uses 8-bit transfers,
to simplify the code. These are the transfers that are not time-critical
since they tend to be small. The case that really matters is reading from
SPI flash.
In general we can use 16-bit reads anytime we are transferring an even
number of bytes. If the code detects an odd number of bytes, it tries to
perform the operation in two steps: once in 16-bit mode with an even
number of bytes, and once in 8-bit mode for the final byte. This allow
us to use 16-bit reads even if asked to transfer (for example) 0xf423
bytes.
The limit on in_now and out_now is adjusted to 0xfffe to avoid an extra
transfer when transferring ~>=64KB.
CQ-DEPEND=CL:383232
BUG=chrome-os-partner:56556
BRANCH=none
TEST=boot on gru and see that things still work correctly. I tested (with
extra debugging) that the 16-bit case is being picked when it should be.
Change-Id: If5effae9a84e4de06537fd594bedf7f01d6a9c88
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: ec250b4931c7d99cc014e32ab597fca948299d08
Original-Change-Id: Idc5b7e5d82cdbdc1e8fe8b2d6da819edf2d5570c
Original-Signed-off-by: Simon Glass <sjg@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/381312
Original-Commit-Ready: Julius Werner <jwerner@chromium.org>
Original-Tested-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16712
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Some of the asserts for valid clock divisor ranges were off by one. This
patch corrects them and writes them all in a consistent way.
BRANCH=None
BUG=None
TEST=Booted Kevin.
Change-Id: I81749408a40822100797f1734f3b88987d12d8d5
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: e09cdfde26700496aaa1fc41489f63a355e8a89d
Original-Change-Id: I429edb99e2d5ff2302d9750e6569b3d21f5686fa
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/381574
Original-Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-on: https://review.coreboot.org/16704
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
This patch moves the big CPU cluster initialization on the RK3399 from
the clock init bootblock function into ramstage. We're only really doing
this to put the cluster into a sane state for the OS, we're never
actually taking it out of reset ourselves... so there's no reason to do
this so early.
Also cleaned up the interface for rkclk_configure_cpu() a bit to make it
more readable.
BRANCH=None
BUG=chrome-os-partner:54906
TEST=Booted Kevin.
Change-Id: I568b891da0abb404760d120cef847737c1f9e3ec
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: bd7aa7ec3e6d211b17ed61419f80a818cee78919
Original-Change-Id: Ic3d01a51531683b53e17addf1942441663a8ea40
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/377541
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-on: https://review.coreboot.org/16698
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
At higher SPI bus speeds the SPI RX value is not available in time for
sampling at the normal time. Add a delay to ensure that we read the
correct data.
The value of 40ns is chosen arbitrarily. In my testing I can use a sample
delay of 1 even at 24MHz. But since it is not necessary, I have left that
case alone. It kicks in at 25MHz and up.
BUG=chrome-os-partner:56556
BRANCH=none
TEST=boot on gru and see no change at current speed
Change-Id: I3ef335d9a532eaef1e76034bd02e185acf11176a
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: e9b620c47fc3e39211487507fadb8657afdebee7
Original-Change-Id: I65d66d752cbbbee4d02f475de23a52069a0e9782
Original-Signed-off-by: Simon Glass <sjg@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/381311
Original-Commit-Ready: Julius Werner <jwerner@chromium.org>
Original-Tested-by: Simon Glass <sjg@google.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16707
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This patch fixes a typo in the clock initialization code that caused the
PERILP1_PCLK_HZ constant to be ignored and the clock to always run at
the same speed as its parent (PERILP1_HCLK_HZ). Since we've done all our
previous tests and validation with this bug, we should probably increase
the value of the constant (that had not actually been used) to the value
that we had been incorrectly using instead (which also makes effective
SPI read times faster).
BRANCH=None
BUG=chrome-os-partner:56556
TEST=Booted Kevin.
Change-Id: Ibeb08f5fe5e984a74e3f57e60c62d4bfb644b6ca
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 06e605a5fcb9bdf13a3d301112380633b892fd4e
Original-Change-Id: Icb5e079f53eb22b0dbf0ea4d1c2ff08688e3fa8e
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/381031
Original-Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-on: https://review.coreboot.org/16703
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Output GPIOs should never have a pull-up or pull-down resistor attached
since they're actively driven. Since some GPIOs get initialized with a
pull at power-on reset, we should explicitly overwrite that setting.
Most other platforms do this on gpio_output, but Rockchip hadn't yet.
Also, shuffle some code around to make things cleaner and allow for
easier code reuse.
BRANCH=None
BUG=chrome-os-partner:52526
TEST=Booted Kevin.
Change-Id: I1425d074ea1e90f4484e1e84a8002b057192c5f7
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: df5b236bfd58b172435043c1cb792b917a4ec4ab
Original-Change-Id: I044266d71ef8bd0518316ff72d829d1ca1e30f35
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/382531
Original-Reviewed-by: Simon Glass <sjg@google.com>
Reviewed-on: https://review.coreboot.org/16710
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
As far as I know, the Cortex-A53 cores in RK3399 are of a newer revision
that is not affected by ARM erratum 843419. If it was, the workaround
would also need to be enabled in libpayload and Chrome OS userspace,
which it currently isn't. I assume this was just incorrectly copied over
from another SoC and we can safely remove it.
BRANCH=None
BUG=chrome-os-partner:56700
TEST=Booted Kevin.
Change-Id: I5b1534c954a6d985499b481738723cabbdc07253
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 4891cc866583532ee3dcb1a5ad5b81670eb0743d
Original-Change-Id: Iadb57428f8727ce0e563204723644e2c79e3007c
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/376363
Original-Commit-Queue: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-on: https://review.coreboot.org/16702
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Kconfig hex values don't need to be in quotes, and should start with
'0x'. If the default value isn't set this way, Kconfig will add the
0x to the start, and the entry can be added unnecessarily to the
defconfig since it's "different" than what was set by the default.
A check for this has been added to the Kconfig lint tool.
Change-Id: I86f37340682771700011b6285e4b4af41b7e9968
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16834
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
The microcode for the BSP gets loaded early from the fit table, but in
case we have newer microcode in cbfs, try to load it again from cbfs.
BUG=chrome-os-partner:53013
TEST=Boot and verify that microcode tries to load into the BSP.
Change-Id: Ifd6c78d7b0eec333b79e0fe5cb6a81981b078f5d
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16829
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
A copy of our uart8250io driver sneaked in with Broadwell-DE support.
The only difference is the lack of initialization (due to FSP handling
that).
TEST=manually compared resulting object files
Change-Id: I09be10b76c76c1306ad2c8db8fb07794dde1b0f2
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/16786
Tested-by: build bot (Jenkins)
Reviewed-by: York Yang <york.yang@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Fix the build issues with FSP 2.0:
* Remove struct from the various data structures.
* Properly display the serial port UPDs.
* Change chipset_handle_reset parameter type
BRANCH=none
BUG=None
TEST=Build FSP 2.0 (SEC/PEI core with all FSP debug off) and run on
Galileo Gen2
Change-Id: Icae578855006f18e7e5aa18d2fd196d300d0c658
Signed-off-by: Lee Leahy <Leroy.P.Leahy@intel.com>
Reviewed-on: https://review.coreboot.org/16808
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Add support for multiple versions of FSP.
BRANCH=none
BUG=None
TEST=Build FSP 1.1 (SEC/PEI core, with all FSP debug off) and run on
Galileo Gen2
Change-Id: Ie7e7f0f883c4d3bfcb18fa25571e505cdde00b2d
Signed-off-by: Lee Leahy <Leroy.P.Leahy@intel.com>
Reviewed-on: https://review.coreboot.org/16807
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Add Kconfig values to select the FSP setup:
* FSP version: 1.1 or 2.0
* Implementation: Subroutine or SEC/PEI core based
* Build type: DEBUG or RELEASE
* Enable all debugging for FSP
* Remove USE_FSP1_1 and USE_FSP2_0
Look for include files in vendorcode/intel/fsp/fsp???/quark
BRANCH=none
BUG=None
TEST=Build FSP 1.1 (subroutine) and run on Galileo Gen2
Change-Id: I3a6cb571021611820263a8cbfe83e69278f50a21
Signed-off-by: Lee Leahy <Leroy.P.Leahy@intel.com>
Reviewed-on: https://review.coreboot.org/16806
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
A dedicated pmc_ipc DSDT entry is required for pmc_ipc kernel driver.
The ACPI mode entry includes resources for PMC_IPC1, SRAM, ACPI IO and
Punit Mailbox.
BRANCH=None
BUG=chrome-os-partner:57364
TEST=Boot up into OS successfully and check with dmesg to see the
driver has been loaded successfully without errors.
Change-Id: I3f60999ab90962c4ea0a444812e4a7dcce1da5b6
Signed-off-by: Zhao, Lijian <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/16649
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Intel telemetry support will require PMC IPC1 and SRAM devices to be
operated in ACPI mode. Then using fixed resources on BAR0, BAR1
and BAR2 (PMC only) for those two devices will help
the resource assignment in DSDT stage.
BUG=chrome-os-partner:57364
BRANCH=None
TEST=Boot up into Chrome OS successfully and check with dmesg to see
the driver has been loaded successfully without errors.
Change-Id: I8f0983a90728b9148a124ae3443ec29cd7b344ce
Signed-off-by: Zhao, Lijian <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/16648
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Instead of having each mainboard provide the power button,
uncondtionally provide the power button ACPI device on behalf
of each mainboard.
BUG=chrome-os-partner:56677
Change-Id: I94c9e0353c8d829136f0d52a356286c6bedcddd5
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16731
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Initialize the PCNT variable in GNVS so it is available to ACPI code
that expects to know the number of CPUs.
Change-Id: I7a6e003ac94218061bf98e8883ed2c62d856af8d
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/16693
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Implement the generic acpi_get_gpe() function to read and clear
the GPE status for a specific GPE.
Tested by watching GPE status in a loop while generating interrupts
manually from the EC console.
BUG=chrome-os-partner:53336
Change-Id: I482ff52051a48441333b573f1cd0fa7f7579a6ab
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/16671
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Initialize the GPEs from mainboard config in bootblock, so they
can be used in verstage to query latched interrupt status.
I still left it called in ramstage just to be sure that the
configuration was not overwritten in FSP stages.
Tested by reading and reporting GPE status in a loop in verstage
and manually triggering an interrupt on EC console.
BUG=chrome-os-partner:53336
Change-Id: Iacd0483e4b3229aca602bb5bb40586eedf35a6ea
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/16670
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
These values are found in util/cbfstool/cbfs.h.
Change-Id: Iea4807b272c0309ac3283e5a3f5e135da6c5eb66
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16646
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
The SPI driver is quite slow at reading data. For example, with a 24MHz
clock on gru it achieves a read speed of only 13.9Mbps.
We can correct this by reading the status registers once, then reading as
many bytes as are available before checking the status registers again. It
seems likely that a status register read requires synchronizing with the
SPI FIFO clock domain, which takes a while.
BUG=chrome-os-partner:56556
BRANCH=none
TEST=run on gru and see the speed increase from 13.920 Mbps to 24.712 Mbps
Change-Id: I24aed0c9c6c5445634c4e056922afaee4e9a7b33
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 49c2fc20d7d7d703763e9b0a6f68313a349a84b9
Original-Change-Id: I42745f01f0fe069f6ae26d866004d36bb257e6b2
Original-Signed-off-by: Simon Glass <sjg@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/376945
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16582
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This patch adds support to reboot the whole board after a hardware
watchdog reset, to avoid the usual TPM issues. Work 100% equivalent to
Veyron.
From my tests it looks like both SRAM and PMUSRAM get preserved across
warm reboots. I'm putting the WATCHDOG_TOMBSTONE into PMUSRAM since that
makes it easier to deal with in coreboot (PMUSRAM is currently not
mapped as cached, so we don't need to worry about flushing the results
back before reboot).
BRANCH=None
BUG=chrome-os-partner:56600
TEST='stop daisydog; cat > /dev/watchdog', press CTRL+D, wait 30
seconds. Confirm that system reboots correctly without entering recovery
and we get a HW watchdog event in the eventlog.
Change-Id: I317266df40bbb221910017d1a6bdec6a1660a511
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 3b8f3d064ad56d181191c1e1c98a73196cb8d098
Original-Change-Id: I17c5a801bef200d7592a315a955234bca11cf7a3
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/375562
Original-Commit-Queue: Douglas Anderson <dianders@chromium.org>
Reviewed-on: https://review.coreboot.org/16578
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Implement the generic acpi_get_gpe() function to read and clear
the GPE status for a specific GPE.
Tested by watching GPE status in a loop while generating interrupts
manually from the EC console.
BUG=chrome-os-partner:53336
Change-Id: Id885e98d48c2133a868da19eca3360e2dfb82e84
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Initialize the GPEs from mainboard config in bootblock, so they
can be used in verstage to query latched interrupt status.
I still left it called in ramstage just to be sure that the
configuration was not overwritten in FSP stages.
Tested by reading and reporting GPE status in a loop in verstage
and manually triggering an interrupt on EC console.
BUG=chrome-os-partner:53336
Change-Id: I1af3e9ac1e5c59b9ebb5c6dd1599309c1f036581
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
This patch sets some magic number in magic undocumented registers that
are rumored to make USB 2.0 signal integrity better on Kevin. I don't
see any difference (unfortunately it doesn't solve the problems with
long cables on my board), but I guess it doesn't hurt either way.
BRANCH=None
BUG=chrome-os-partner:56108,chrome-os-partner:54788
TEST=Booted Kevin with USB connected through Servo. Seems to have
roughly the same failure rate as before.
Change-Id: If31fb49f1ed7218b50f24e251e54c9400db72720
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 0c5c8f0f80ea1ebb042bcb91506a6100833e7e84
Original-Change-Id: Ifbd47bf6adb63a2ca5371c0b05c5ec27a0fe3195
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/370900
Original-Reviewed-by: Guenter Roeck <groeck@chromium.org>
Original-Reviewed-by: David Schneider <dnschneid@chromium.org>
Reviewed-on: https://review.coreboot.org/16265
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Add FSP 2.0 support in ramstage.
Populate required Fsp Silicon Init params and configure mainboard
specific GPIOs.
Define function fsp_soc_get_igd_bar needed by fsp2.0 driver for
pre OS screens.
Change-Id: Ib38ca7547b5d5ec2b268698b8886d5caa28d6497
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/16592
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
When the boot media is memory mapped mark it as cacheable
after romstage. Otherwise the boot media is uncacheable and
all loads from it take longer. Loading FSP-S alone in ramstage
went down to 17.5ms from 54ms.
BUG=chrome-os-partner:56656
Change-Id: I6703334ba8fe98aca26ba1c995d6d3abb0ddef33
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16613
Reviewed-by: Andrey Petrov <andrey.petrov@intel.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Currently we are setting the gpio_tier1_sci in smihandler before
going to S3. But this won't work for S0iX as it happens from Linux
kernel and SMI handler is not involved in that flow. We need to
set this bit i.e. bit 15 in ACPI gpe0a register at 0x430h. The Linux
kernel before going to sleep checks what values are passed through
ASL as wake events (through _PRW), keeps those enabled only and
clears other bits in gpe0 enable registers. So we need to inform
the kernel to keep gpio_tier_sci also set as these are needed for
any wake event. This patch adds ASL code for sleep button device with
HID id PNP0C0E. We are adding _PRW method for sleep button device
with this patch.
BUG=chrome-os-partner:56483
TEST=System resumes from S3 on lidopen, powerbutton and USB wake.
Also from S0iX system is resuming for WIFI wake.
Change-Id: Ie8517cad9cd37c25788c22250894d4f9db344ff9
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/16564
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
move lb_framebuffer function in soc/intel/apollolake
to driver/intel/fsp20 so that fsp 2.0 bases soc's can
use common lb_framebuffer function.
Change-Id: If11bc7faa378a39cf7d4487f9095465a4df84853
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/16549
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Populate SoC related Memory initialization params.
Post memory init, set DISB, setup stack and MTRRs using the postcar
funtions provided in postcar_loader.c.
TEST=Build and boot kunimitsu, dram initialization done.
ramstage is loaded.
Change-Id: I8d943e29b6e118986189166d92c7891ab6642193
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/16315
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
It is very useful to have the ability to see I2C transactions
performed by the host firmware. This patch adds a simple
Kconfig option that will enable debug output.
Change-Id: I55f1ff273290e2f4fbfaea56091b2df3fc49fe61
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/16590
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
This change modifies the lpss_i2c driver to behave more like
the Linux kernel driver. In particular the controller is only
enabled when processing a transaction, and is disabled after.
This means that errors in one transaction will not affect later
transactions.
Also when disabling the controller the code is supposed to wait
on the enable bit in the "enable status" register and not in
the enable control register. In order to get access to this
register the reg map was expanded to include all registers.
This was tested with the cr50 TPM driver to ensure that if a
transaction does fail that it can be successfully retried instead
of the bus being unusable.
Change-Id: I43a546d54996ba0f08550a801927b8f7a6690cda
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/16589
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Due to an incorrect value set for the power limit PL1, the
system is not able to leverage full TDP capacity. FSP code
sets the PL1 value as 6W in RAPL MMIO register based on
fused soc tdp value. This RAPL MMIO register is a physically
separate instance from RAPL MSR register. This patch sets
PL1 value to 15W in RAPL MMIO register.
BUG=chrome-os-partner:56524
TEST=Built, booted on reef and verifed the package power
with heavy workload.
Change-Id: Ib344247cd8d98ccce7c403e778cd87c13f168ce0
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/16595
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This implements GNVS variable to store the address of PERST_0,
_ON/_OFF methods to power gate PCIe during S0ix entry, and
PERST_0 assertion/de-assertion methods.
BUG=chrome-os-partner:55877
TEST=Suspend and resume using 'echo freeze > /sys/power/state'.
System should resume with PCIE and wifi functional.
Change-Id: I9f63ca0b8a6565b6d21deaa6d3dfa34678714c19
Signed-off-by: Vaibhav Shankar <vaibhav.shankar@intel.com>
Reviewed-on: https://review.coreboot.org/16351
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The code was not previously initializing the GNVS structure
to all 0's in the ACPI write tables path. Fix this and also
rearrange the ordering of updating the fields to only handle
the chip_info specific bits till last such that most of the
structure is filled in prior to bailing out in the case of a
bad devicetree.
Change-Id: I7bdb305c6b87dac96af35b0c3b7524a17ce53962
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16597
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This driver is only a prototype driver, real driver
will be integrated at a later time.
Testing: booted successfully.
Change-Id: I372764962e96e5c9c827d524bc369978c5c1fda8
Signed-off-by: Hakim Giydan <hgiydan@marvell.com>
Reviewed-on: https://review.coreboot.org/16554
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
This driver uses BootROM callback to read and write
to the nvm using I2C.
Testing: booted successfully.
Change-Id: I8639af3e004f6631d7e596507c106159835f979f
Signed-off-by: Hakim Giydan <hgiydan@marvell.com>
Reviewed-on: https://review.coreboot.org/16161
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
APMU is the AP power management unit.
It is a separate processor that handles enabling
individual power rails.
This driver handles sending and receiving commands
from/to APMU.
Testing: booted successfully.
Change-Id: I5ae07849f8432bece8a0ae9066a3f786e6e8d2fe
Signed-off-by: Hakim Giydan <hgiydan@marvell.com>
Reviewed-on: https://review.coreboot.org/15518
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Load_validate: it loads and validates images from
flash using hash values stored in the BDB.
Testing: booted successfully.
Change-Id: I0b00e8c60ed76622d03cb232d5c4273b4077aae7
Signed-off-by: Hakim Giydan <hgiydan@marvell.com>
Reviewed-on: https://review.coreboot.org/16148
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Most things still need to be filled in, but this will allow
us to build boards which use this SOC.
Nvidia Tegra210 SOC and Rochchip Rk3399 SOC has been used
as templates to create this directory.
Change-Id: I8cc3e99df915bb289a2f3539db103cd6be90a0b2
Signed-off-by: Hakim Giydan <hgiydan@marvell.com>
Reviewed-on: https://review.coreboot.org/15506
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
The serial IRQ (SERIRQ) used by the LPC interface can operate either in
continuous or in quiet mode. Add a Kconfig switch to select the desired
mode. This switch can now be used on mainboard level to enable the
needed mode per mainboard.
Change-Id: Ibe246b88164a622f9c71ebe7bab752a083a49a62
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/16575
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Since this mainboard provides 4 COM ports on LPC, enable decoding of
the corresponding addresses using the generic LPC decode registers.
Change-Id: I0e93d40dca01d55f3567a18c7ec02269e3bec466
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/16535
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The serial IRQ configuration register is only 8 bit wide so switch the
PCI access from 16 bits to 8 bits.
Change-Id: Ia9fbc02251e00b31440bf103e2afc2ff285b7f2e
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/16534
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
For an unknown reason the printed address in the SPI debug messages is
modified before it is printed by subtracting the constant 0xf020 from
the passed in address.
What I suppose this debug code should do is to print the used register
address within the SPI controller while any parts of this address that
belongs to the SPI base address should be omitted. To fix that remove
the subtraction of 0xf020 and adjust the address mask to 0x3ff so that
only the offset to the registers inside the SPI controller will be
visible in the debug messages.
In addition switch to uint8_t and friends over u8 to sync up with used
types in this file.
Change-Id: I93ba7119873115c7abc80a214cc30363a6930b3b
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/16500
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: York Yang <york.yang@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
DIV_ROUND_CLOSEST and DIV_ROUND_UP are useful macros for other
architectures. This patch moves them from soc/nvidia/tegra/types.h
to commonlib/include/commonlib/helpers.h .
Change-Id: I54521d9b197934cef8e352f9a5c4823015d85f01
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/16415
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Use the config switch CONFIG_DEBUG_SPI_FLASH on compiler level rather
then on preprocessor level to ensure that the code is compiled even if
the switch is not selected. In addition the following two changes are
introduced:
1. Prepend the debug messages with 'SPI:' to make the output more
meaningful.
2. Change the address mask from 0xffff to 0x3ff and remove the subtraction
of the constant value 0xf020 in order to print only the register
offset within the SPI controller and avoid the visibility of any
fragments from SPI base address.
3. Switch to uint8_t and friends instead of u8 to sync up with other
code in the same file.
Change-Id: Iaf46f29a775039007a402fe862839df06a4cbfaa
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/16499
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The pull up for CLKRUN is required to resolve keyboard slowness
and malfunctioning observed on some reef systems. The CLKRUN
signal was probed and found to be floating when the pull up
was not enabled. Also Added pull ups for the LPC Multiplexed
command, address and data lines LAD0:3 because the LPC
Interface specification requires them.
BUG=chrome-os-partner:55586
BRANCH=none
TEST=When a key is pressed, the character is immediately visible
on the screen. Also the interrupt count for i8042 increments
immediately in /proc/interrupts.
Change-Id: I16df1a0301a3994c926a609f61291761219f9e01
Signed-off-by: Shamile Khan <shamile.khan@intel.com>
Reviewed-on: https://review.coreboot.org/16426
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Commit 93ef3ff makes the following only print the part number when
the ROM is built. In Makefile.inc, $(MAINBOARDDIR) is the variable
that has the quotes stripped off from $(CONFIG_MAINBOARD_DIR), so
use it instead of $(MAINBOARD_DIR).
build_complete:: coreboot
printf "\nBuilt %s (%s)\n" $(MAINBOARD_DIR) \
$(CONFIG_MAINBOARD_PART_NUMBER)
Change-Id: I729a583182937db7a926eb75aa28dfb53360046c
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/16410
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Increase the default timeout in the LPSS I2C driver to 4ms
from 2ms. During testing with some slower devices I found
that the existing timeout could be too short leading to
transaction failures.
Change-Id: Ied86c7a0aa26d55b31f447c5938803c194d0045e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/16392
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
FSP header files should be located in vendorcode, not soc directory.
This patch includes changes any references to the old location to
the new location.
Change-Id: I44270392617418ec1b9dec15ee187863f2503341
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/16310
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The following patch is based off of the UEFI 2.6 patch. The FSP header files
are temporarily staying in soc/intel/apollolake and FspUpd.h has been relocated
since the other headers expect it to be in the root of an includable directory.
Any struct defines were removed since they are defined in the headers and no
longer need to be explicity declared as struct with the UEFI 2.6 includes.
BUG=chrome-os-partner:54100
BRANCH=none
TEST=confirmed coreboot builds successfully
Change-Id: I10739dca1b6da3f15bd850adf06238f7c51508f7
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>#
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/16308
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
All but ga-g41m-es2l/cmos.default had multiple final newlines.
ga-g41m-es2l/cmos.default had no final newline.
Change-Id: Id350b513d5833bb14a2564eb789ab23b6278dcb5
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/16361
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Antonello Dettori <dev@dettori.io>
Instead of using a mix of _N and _NORTH, _NW and _NORTHWEST for GPIO
community names, follow one single convention. This allows for re-using
macros easily.
Change-Id: Icd9cf9ef70d03576d864688cf5d6946124c259c3
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/16353
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Before, we calculate the pwm duties for cpu cores and centerlogic by
hand, adding pwm_regulator.c to handle this. The default pwm design
min/max voltage may be different between revs.
With the pwm regulator, this patch changes the little cpu frequency from
600M to 1512M, and raises CPU voltage to 1.2V correspondingly.
This also means we decide to drop the ES1 because it may fail to
bootup with 1.5G ~ 1.2v.
BRANCH=none
BUG=chrome-os-partner:54376,chrome-os-partner:54862
TEST=Bootup on kevin board
Change-Id: Id04c176bddfb9cdf3d25b65736e40249a85f6aa1
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: ee4365c787ec523b7ee1028ea100dcfbb331b3a9
Original-Change-Id: Ide75bbd92d1cbb14f934baeec0e38862bc08402b
Original-Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Original-Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/364410
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16368
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Add Initial pieces of code to support fsp2.0 in skylake keeping
the fsp1.1 flow intact.
The soc/romstage.h and soc/ramstage.h have a reference to
fsp driver includes, so split these header files for
each version of FSP driver.
Add the below files,
car_stage.S:
Add romstage entry point (car_stage_entry).
This calls into romstage_fsp20.c and aslo handles
the car teardown.
romstage_fsp20.c:
Call fsp_memory_init() and also has the callback
for filling memory init parameters.
Also add monotonic_timer.c to verstage.
With this patchset and relevant change in kunimitsu mainboard,
we are able to boot to romstage.
TEST= Build and Boot Kunimitsu with PLATFORM_USES_FSP1_1
Build and Boot Kunimitsu to romstage with PLATFORM_USES_FSP2_0
Change-Id: I4309c8d4369c84d2bd1b13e8ab7bfeaaec645520
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/16267
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
The romstage.c is more board related than soc specific, like
setting the pwm regulators, so moving it to mainboard/gru.
BRANCH=none
BUG=chrome-os-partner:54819
TEST=Bootup on kevin board
Change-Id: I83c6cde9f451480e47e2b4b549cedf65b345134c
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 35feeb07131a6a9de4adde035236987391833474
Original-Change-Id: If2bf245302eb4fb20bb089c1b3ffa03909722443
Original-Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/375398
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16367
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Certain LPDDR4 models have some HW issues that can be worked around
by turning off Periodic Retraining feature in the memory controller.
Add option to disable PR per SKU.
BUG=chrome-os-partner:55466
TEST=run RMT test, pass
Change-Id: Ie7aa79586665f6d3a7edd854a9eef07e6a1b2ab8
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/16320
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Update FSP Header files to provide UPD for periodic training
disable. This is for the SIC 1.1.3/150_11 FSP release.
BUG=chrome-os-partner:54100
BRANCH=none
TEST=built coreboot image with new headers for reef
Change-Id: I2ba11aa3d2d664c1d34e39c4c8144fb1c4f2149a
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/16352
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Currently boards based on fsp_broadwell_de fail to compile if the config
switch CONFIG_DEBUG_SPI_FLASH is selected. The error is caused by the
usage of const for the address pointer in the functions writeb_, writew_
and writel_. The reason why it stayed hidden for so long is the fact that
the switch is used with the preprocessor and nobody really selects it
until there is a bug one want to find in this area.
This patch fixes the parameter type definition which solves the error.
In addition the config switch is not used on preprocessor level anymore
but instead on compiler level. This ensures that at least the code
syntax is checked on build time even if the config option is not
selected. Also prefix the messages with "SPI:" to make them more
meaningful in a full log.
Change-Id: I3514b0d4c08bf5a4740f2632641e09af1b3aaf3a
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/16347
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
In order to provide time for the S0 rails to discharge one needs
to be able to set the SLP_S3_L assertion width. The hardware default
is 60 microcseconds which is not slow enough on most boards. Therefore
provide a devicetree option for the mainboard to set accordingly
for its needs. An unset value in devicetree results in a conservative
2 second SLP_S3_L duration.
BUG=chrome-os-partner:56581
Change-Id: I6c6df2f7a181746708ab7897249ae82109c55f50
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16326
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Andrey Petrov <andrey.petrov@intel.com>
Add new option to set up Cache-As-RAM by using CQOS, Cache Quality of
Service. CQOS allows setting ways of cache in no-fill mode, while keeping
other ways in regular evicting mode. This effectively allows using CAR
and cache simultaneously.
BUG=chrome-os-partner:51959
TEST=switch from NEM to CQOS and back, boot
Change-Id: Ic7f9899918f94a5788b02a4fbd2f5d5ba9aaf91d
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/15455
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Since whole L2 (1MiB) is not used, it is possible to shrink CAR size
to 768 KiB. Since 768 KiB is not power of two, 2 MTRRs are used to
set it up. This is a part of CQOS enabling.
BUG=chrome-os-partner:51959
Change-Id: I56326a1790df202a0e428e092dd90286c58763c5
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/15453
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Since we now have so much more room for activities in our romstage SRAM
section, we can easily fit the LZMA decompressor to enable ramstage
compression. Also shuffle around memlayout sections a little more to
make use of unused space, and balance out leftover memory so that all
sections that might need future expansion have a reasonable amount.
Change-Id: I47f2d03e520fc3103ef04257b4ba7e93874b8956
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16334
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch changes Gru SDRAM parameters from structures that just get
compiled into the romstage to individual CBFS files. This allows us to
only load the parameter set we need for the board we're booting from
flash, which reduces our boot time and the SRAM memory footprint
required to hold the romstage.
TEST=Booted Kevin.
Change-Id: Ie88a515cbdb19a794ca0a230a56bcc82bed1e550
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16274
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Add in the base for ELOG for APL. Some PM events still need to be
added but the basic events are logged here. This enables the
basic functionality of ELOG for Apollolake.
BUG=chrome-os-partner:55473
BRANCH=none
TEST=Verified image boots on Amenia
Change-Id: I8682293e5a55b3efb5fdd9f1be1f3e4bf8d0757c
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/15937
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Call power management utility function clear_wake_sts
from southbridge_smi_sleep before going to sleep.
This is needed to clear the wake status bits in ACPI
registers GPE0.
BUG=chrome-os-partner:55583
BRANCH=None
TEST=Verified that system goes to sleep on lidclose and
powerd_dbus_suspend command issued from built-in
keyboard.
Change-Id: I204a59f8a19137d6a192ea2d89939eefcd5d41ce
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/16299
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch adds a power management utility function to
clear wake status bits in ACPI GPE0 registers. We need
to call this function before going to sleep from
common smi handler function.
BUG=chrome-os-partner:55583
BRANCH=None
TEST=Verified that system goes to sleep on lidclose and
powerd_dbus_suspend command issued from built-in
keyboard.
Change-Id: Icd095d377c82f2e154f2e2db773f737aa49cda64
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/16298
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
When UART_DEBUG is enabled bootblock size grows more than the current
32K. Bump this up to 48K.
Change-Id: I580137dfdc9b4ad226c866f2b23b159bd820c62c
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/16317
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The chromium tree is currently using a different config for
Chrome OS than what is being built in coreboot.org. Align those
settings to reflect how skylake Chrome OS boards are actually
shipped to provide proper parity between coreboot.org and chromium.
Change-Id: I7ab9c1dfa8c6be03ac2125fb06cb7022f3befa97
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16313
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Implement PS0 and PS3 methods to support eMMC power gate
in S0ix suspend and resume.
BUG=chrome-os-partner:53876
TEST=Suspend and Resume using 'echo freeze > /sys/power/state'.
System should resume from S0ix.
Change-Id: Ia974e9ed67ee520d16f6d6a60294bc62a120fd76
Signed-off-by: Vaibhav Shankar <vaibhav.shankar@intel.com>
Reviewed-on: https://review.coreboot.org/16233
Tested-by: build bot (Jenkins)
Reviewed-by: Venkateswarlu V Vinjamuri <venkateswarlu.v.vinjamuri@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Update the config variable that gets set to use DMIC 2 channel blob for
intel/apollolake platforms. This flag is set in mainboard.
Change-Id: Ic6deb9f08d345cc45351d61a7597bc7075ee20f9
Signed-off-by: Saurabh Satija <saurabh.satija@intel.com>
Reviewed-on: https://review.coreboot.org/16251
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Calling halt in poweroff when in SMM prevents SLP_SMI to be triggered
preventing the system from entering sleep state. Fix this by calling
halt only if ENV_SMM is not true.
BUG=chrome-os-partner:56395
Change-Id: I3addc1ea065346fbc5dbec9d1ad49bbd0ae05696
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/16259
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Calling halt in poweroff when in SMM prevents SLP_SMI to be triggered
preventing the system from entering sleep state. Fix this by calling
halt only if ENV_SMM is not true.
BUG=chrome-os-partner:56395
BRANCH=None
TEST=Verified lidclose behavior on reef.
Change-Id: If116c8f4e867543abdc2ff235457c167b5073767
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/16257
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
sts_index is calculated incorrectly because of wrong use of
parenthesis. This lead to wrong bit being checked for EC_SMI_GPI on reef
and lidclose event was missed.
BUG=chrome-os-partner:56395
BRANCH=None
TEST=Verified that lidclose event is seen and handled by SMM in
coreboot on reef.
Change-Id: I56be4aaf30e2d6712fc597b941206ca59ffaa915
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/16256
Tested-by: build bot (Jenkins)
Reviewed-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Read FSP produced memory HOB and use it to populate DIMM info.
DIMM 'part_num' info is stored statically based on memory/SKU id.
BUG=chrome-os-partner:55505
TEST='dmidecode -t 17' and 'mosys -k memory spd print all'
Change-Id: Ifcbb3329fd4414bba90eb584e065b1cb7f120e73
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com>
Reviewed-on: https://review.coreboot.org/16246
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
If the boot device is SPI flash use the common one in the
early stages. While tweaking the config don't auto select
SPI_FLASH as that is handled automatically by the rest of the
build system.
BUG=chrome-os-partner:56151
Change-Id: Ifd51a80fd008c336233d6e460c354190fcc0ef22
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16202
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
If the boot device is SPI flash use the common one in the
early stages. While tweaking the config don't auto select
SPI_FLASH as that is handled automatically by the rest of the
build system.
BUG=chrome-os-partner:56151
Change-Id: If5e3d06008d5529dd6d7c05d374a81ba172d58fd
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16201
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Using malloc() in SPI code is unnecessary as there's only
one SPI device that the SoC support code handles: boot
device. Therefore, use CAR to for the storage to work around
the current limiations of the SPI API which expects one to
return pointers to objects that are writable. Additionally,
include the SPI support code as well as its dependencies in
all the stages.
BUG=chrome-os-partner:56151
Change-Id: I0192ab59f3555deaf6a6878cc31c059c5c2b7d3f
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16196
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Lee Leahy <leroy.p.leahy@intel.com>
Using malloc() in SPI code is unnecessary as there's only
one SPI device that the SoC support code handles: boot
device. Therefore, use CAR to for the storage to work around
the current limiations of the SPI API which expects one to
return pointers to objects that are writable.
BUG=chrome-os-partner:56151
Change-Id: If4f5484e27d68b2dd1b17a281cf0b760086850a7
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16195
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Indicate to the build system that a platform provides support
for a writable boot device. The following will provide the
necessary support:
COMMON_CBFS_SPI_WRAPPER users
soc/intel/apollolake
soc/intel/baytrail
soc/intel/braswell
soc/intel/broadwell
soc/intel/skylake
The SPI_FLASH option is auto-selected if the platform provides
write supoprt for the boot device and SPI flash is the boot
device.
Other platforms may provide similar support, but they do that
in a device specific manner such as selecting SPI_FLASH
explicitly. This provides clearance against build failures
where chipsets don't provide SPI API implementations even
though the platform may use a SPI flash to boot.
BUG=chrome-os-partner:56151
Change-Id: If78160f231c8312a313f9b9753607d044345d274
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16211
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Make the indication of the boot device being memory mapped
separate from SPI. However, retain the same defaults that
previously existed.
BUG=chrome-os-partner:56151
Change-Id: I06f138078c47a1e4b4b3edbdbf662f171e11c9d4
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16228
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
In SMM, gpio configuration could be done to avoid leakage. ITSS
configuration is not required when entering sleep. Thus, bail out early
from itss configuration if in SMM.
BUG=chrome-os-partner:56281
Change-Id: I4d8be0513aa202f001f980bb91986b50b8ed2a5b
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/16242
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Provide a default value of 0 in drivers/spi as there weren't
default values aside from specific mainboards and arch/x86.
Remove any default 0 values while noting to keep the option's
default to 0.
BUG=chrome-os-partner:56151
Change-Id: If9ef585e011a46b5cd152a03e41d545b36355a61
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16192
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
DCACHE_RAM_SIZE_TOTAL is set to 0x40000 and is being used to
set up CAR. Whereas DCACHE_RAM_SIZE which is set to 0x10000
is used to calculate the _car_region_end in car.ld. If the FSP CAR
requirement is greater than or even close to DCACHE_RAM_SIZE then,
the CAR region for FSP will be determined to be below the overall
CAR region boundary i.e, out of CAR memory range.
This is working with FSP 1.1 because we provide the FspCarSize
and FspCarBase explicitly in a UPD. Hence, FSP is still able to
use the upper region of CAR memory for its purpose.
However, it will be a problem in case of FSP2.0 where FSP usable CAR
is calculated using _car_region_end.
So, Remove the the use of DCACHE_RAM_SIZE_TOTAL and set
DCACHE_RAM_SIZE to correct value i.e, 0x40000(256KB)
Change-Id: Ie2cb8bb0705a37edb3414850d7659f8a3dd6958b
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/16236
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins)
There is a lot of code that is being referred to in bootblock but
resides under skylake/romstage folder. Hence move this code
into skylake/bootblock, and update the relevant header files
and Makefiles.
TEST=Build and Boot kunimitsu.
Change-Id: If94e16fe54ccb7ced9c6b480a661609bdd2dfa41
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/16225
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Prepare Skylake for FSP2.0 support.
We do not use FSP-T in FSP2.0 driver, hence guard the
FspTempRamInit call under a switch.
In addition to the current early PCH configuration
program few more register, so all in all we do the following,
* Program and enable ACPI Base.
* Program and enable PWRM Base.
* Program TCO Base.
* Program Interrupt configuration registers.
* Program LPC IO decode range.
* Program SMBUS Base address and enable it.
* Enable upper 128 bytes of CMOS.
And split the above programming into into smaller functions.
Also, as part of bootblock_pch_early_init we enable decoding
for HPET range. This is needed for FspMemoryInit to store and
retrieve a global data pointer.
And also move P2SB related definitions to a new header file.
TEST=Build and boot Kunimitsu
Change-Id: Ia201e03b745836ebb43b8d7cfc77550105c71d16
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/16113
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
pmc_gpe_route_to_gpio returns -1 on error. However, the value was being
stored in unsigned int and compared against -1. Fix this by using local
variable ret.
Change-Id: I5ec824949d4ee0fbdbb2ffdc9fc9d4762455b27b
Reported-by: Coverity ID 1357443, 1357442, 1357441
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/16218
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
We're changing the PWM regulator bounds on Kevin from rev6 onwards, so
we'll need to use different duty cycle values for them. We really want a
proper PWM regulator driver that can calculate these values
automatically from voltages, but until we have that this patch just
hardcodes the new numbers in.
(Yes, this is a patch for the mainboard/google/gru board family that only
touches a file from the rockchip/rk3399 SoC. That too is something
that'll be fixed up in a later CL.)
BRANCH=None
BUG=chrome-os-partner:54888
TEST=Booted Kevin rev4 (for whatever that's worth...).
Change-Id: Ibb6ab5c6517d83ffb5e32cb17d0de33e8ec10293
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 4cb2a939295e2b6443c5dbd3374982224322304b
Original-Change-Id: I8757cc54f2478d20bb948a1a0a7398b0404a7b1f
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/368410
Original-Commit-Ready: Dan Shi <dshi@chromium.org>
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-on: https://review.coreboot.org/16235
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Program MCHBAR, DMIBAR, EPBAR, EDRAMBAR and GDXCBAR.
Also program the PAM registers. The system agent was being
programmed in romstage during pre-console initialization, after
moving to C_ENVIRONMENT bootblock this was missing, restoring
the same.
TEST=Build and Boot Kunimitsu
Change-Id: Iaf310cfb83e58eb8d5affb481dfc343f5d45961b
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/16224
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This reverts commit 462e1413 ("rockchip: rk3399: enable sdhci clk
for emmc")
Enabling this clock in coreboot is no longer needed as it's handled
in the kernel driver now.
BUG=chrome-os-partner:52873
TEST=boot from usb/sdcard and check there is /dev/mmcblk0
BRANCH=none
Change-Id: I92cf51f175fe56a09ab9329b29a27c77ef4328e1
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 5707d1269a253dabf825be120d1f9348ffaab6d0
Original-Change-Id: I8bca870c663d8ce8fac5daaaaf8225489f22ed13
Original-Signed-off-by: Shunqian Zheng <zhengsq@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/367421
Original-Commit-Ready: Brian Norris <briannorris@chromium.org>
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16152
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This reverts commit a83bbf5854.
This was submitted out of order.
Change-Id: Ic5a28faf94c1f1901a72e46343722eb4224c5086
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16226
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
The SPI host controller for the SPI boot device doesn't allow
normal probing because it uses the hardware sequencer all
the time. Therefore, it's pointless to include unnecessary
SPI flash drivers.
BUG=chrome-os-partner:56151
Change-Id: Ifcc6492b4bccf7d01b121d908976c9087d12deb0
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16189
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
The SPI host controller for the SPI boot device doesn't allow
normal probing because it uses the hardware sequencer all
the time. Therefore, it's pointless to include unnecessary
SPI flash drivers.
BUG=chrome-os-partner:56151
Change-Id: I04551fdb0b207c7ec2f1f171cff62ed7334a5ad5
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16188
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Make the indication of the boot device being memory mapped
separate from SPI. However, retain the same defaults that
previously existed.
BUG=chrome-os-partner:56151
Change-Id: Ibdd7c8754f9bf560a878136b1f55238e2c2549d3
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16193
Reviewed-by: Andrey Petrov <andrey.petrov@intel.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Having an assignment in assert does not make sense. This seems like it
was intended to check if chip is always same as segments->chip.
Change-Id: I297d9e76a0404a1f510d43f8b9c39e96b557689f
Reported-by: Coverity ID 1357439
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/16219
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Lee Leahy <leroy.p.leahy@intel.com>
The function name "pmc_tco_regs" is changed to "smbus_tco_regs"
since TCO offsets belongs to SMBUS PCI device.
BUG=none
BRANCH=none
TEST=Built and booted kunimitsu
Change-Id: I4ac26df81a8221329f2b45053dd5243cd02f8ad7
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/16155
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
This patch enables the CHROMEOS_RAMOOPS_NON_APCI Kconfig option as a
default across all non-x86 Chrome OS boards.
CQ-DEPEND=CL:367905
BRANCH=None
BUG=None
TEST=See depthcharge CL.
Change-Id: If14ef4f9b1bd480f2d52df3892c73059bb9b07d5
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 8c3b74fb21aadd6de7af62f32fa98fc211d75085
Original-Change-Id: I16ff7f68762a995cd38e5fddaf6971d4b9f07e21
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/368010
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16154
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
FSP unconditionally locks parts of the NVRAM in the RTC.
This change will enable coreboot to update the locking policy
and be able to unlock the region
BUG=chrome-os-partner:55944
TEST=Check 'crossystem dev_boot_usb=1'
Change-Id: I70fd2bafa6ff9eb9cdf284b9780e4b90dee0f4ce
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com>
Reviewed-on: https://review.coreboot.org/16144
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Giri P Mudusuru <giri.p.mudusuru@intel.com>
3ms delay was found in testing to be sufficient for
qup_i2c_write_fifo_flush(), but 1 additional ms was added to give
additional headroom.
Change the Delay from 10ms to 4ms.
BUG=b:28942403
TEST=Boot up Gale board and the TPM functions normally.
BRANCH=None
Change-Id: I6821e2a101cc44e11d74eb6a6215aa9b848ae8c6
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: d93520fab15c5695ea18db21d0f3b24a108f204d
Original-Change-Id: I202f5b8a1ef62bb039c56ba5a25b48b205cf4a67
Original-Signed-off-by: Kan Yan <kyan@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/357961
Original-Reviewed-by: Suresh Rajashekara <sureshraj@chromium.org>
Original-Reviewed-by: SARAVANAKUMAR SUDALAI <ssudalai@qti.qualcomm.com>
Reviewed-on: https://review.coreboot.org/16126
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
The Rockchip RK3399 integrates a USB Type-C PHY in charge of things like
SuperSpeed line muxing for rotated cable orientations in the SoC. While
fancy, this is very complicated and we don't want to implement support
for the whole thing in firmware. The USB Type-C standard has
intentionally been designed in a way that the USB 2.0 (HighSpeed) lines
always "just work" in any orientation (by just shorting different pins
in the connector together) so that simple use cases like ours can get
basic USB functionality without much hassle.
However, a semi-configured Type-C PHY can confuse USB 3.0 capable
devices into thinking we're actually supporting SuperSpeed, and fail at
that rather than establishing a reliable HighSpeed connection. This
patch sets enough bits in the Type-C PHY to electrically isolate the
SuperSpeed lines from the connector so that the connected device isn't
going to get any fancy ideas and reliably falls back to USB 2.0.
Also clean up the rest of the USB code while we're at it: avoid writing
a few bits that are already in the right state from their reset values
anyway, or reading values whose content we already know for this SoC.
Rename the USB controllers to the name actually used in the Rockchip
documentation (USB OTGx) rather than the name blindly copied from
Exynos code (USB DRDx).
BRANCH=None
BUG=chrome-os-partner:54621
TEST=Plug a USB 3.0 Patriot Memory stick into both ports in all
orientations, observe how it gets reliably detected now (safe for some
known hardware issues on my board).
Change-Id: Ifce6bcddd69f2e8f2e2a2f48faf65551e084da1e
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: c526906f998bf66067d3addb8b3d3a126c188b1e
Original-Change-Id: Ie80a201a58764c4d851fe4a5098a5acfc4bcebdf
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/366160
Original-Reviewed-by: liangfeng wu <wulf@rock-chips.com>
Original-Reviewed-by: Shelley Chen <shchen@chromium.org>
Original-Reviewed-by: <515506667@qq.com>
Reviewed-on: https://review.coreboot.org/16125
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This patch enables serial debug functionality for ASL code based on
UART type(legacy/LPSS).
From Skylake onwards all Intel platform uses LPSS based UART for serial
console hence provide option to redirect ASL log over LPSS UART.
Example:
Name (OBJ, 0x12)
APRT (OBJ)
APRT ("CORE BOOT")
Output:
0x12
CORE BOOT
BUG=none
BRANCH=none
TEST=Built and boot kunimitsu to ensure to be able to get ASL console log.
Change-Id: I18c65654b8eb1ac27af1f283d413376fd79d47db
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/16070
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
When booting Linux as a coreboot payload, serial access does not work
properly. This is because the setup code erroneously sets IRQ3 and
IRQ4 to level. The UART on Broadwell is 8250/16550 compatible, thus
ISA and edge-triggered.
This change is not necessary on the non-FSP version of Broadwell support.
The non-FSP version does not set these IRQ overrides.
Fix verified booting Linux 4.6.0-rc2 on Intel Camelback Mountain CRB,
using Intel FSP 1.0.
Change-Id: I17b466676e7f4891c3e75ce6208e1580c9eaf742
Signed-off-by: Kevin Paul Herbert <kevin@trippers.org>
Reviewed-on: https://review.coreboot.org/16065
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Prior to this patch, time->wday was not being initialized in rtc_get(),
but was still being used by rtc_display() to print a day.
Set to -1 which gets printed as "unknown ".
Fixes coverity issue 1357459 - Uninitialized scalar variable
Change-Id: Idecb7968f854df997b58a342e1a06a879f299394
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/15899
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Switch from passing FSP the serial port address to passing FSP the
serial port output routine. This enables coreboot to use any UART in
the system and also log the FSP output.
TEST=Build and run on Galileo Gen2
Change-Id: I67d820ea0360a3188480455dd2595be7f2debd5c
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/16105
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
The variable MAINBOARD_DIR already has the quotes stripped off.
Change-Id: Ib434ce92bdbc49180fb3f713b26d65ba4cf8c441
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/16117
Tested-by: build bot (Jenkins)
Reviewed-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
GPIOs which trigger SMIs set the GPIO_SMI_STS status bits in SMI_STS
register. This patch also sets the SMI_EN bit in enable register for
each community based on GPIOROUTSMI bit in gpio pad. When SMI on a
gpio happens status needs to be gathered on gpio number which is done
by reading the GPI_SMI_STS and GPI_SMI_EN registers.
BUG=chrome-os-partner:54977
TEST=When system is in firmware mode executing the command
lidclose from ec console shuts down the system.
Change-Id: Id89a526106d1989c2bd3416ab81913e6cf743d17
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/15833
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
As no more mainboards are utilizing this SoC support code remove
it. It can be resurrected if ever needed.
BUG=chrome-os-partner:55932
Change-Id: Ic3caf6e6c9b62d012679b996abaa525c8bf679a9
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16108
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
We were using the wrong register when reading the obs value and setting
the DQS driver. This did not affect LPDDR3 performance, but still needs
to be fixed.
BUG=none
BRANCH=none
TEST=boot from kevin
Change-Id: I144f575e27fba11872a8c5463ab1e2986f385ede
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 98221e6b03fc09cbf62af29a270e7a8aa8dfb986
Original-Change-Id: Ie179f9a2955c5712951d40b3ada9c14a51c09c8d
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/363170
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/16052
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
In FIFO mode, the I2C driver was not able to fetch
more than 32 bytes of data from the TPM device. Switch to
block mode to be able to read more data.
BUG=chrome-os-partner:51096
TEST=TPM commands succeed
BRANCH=None
Change-Id: Ib52a1b03667f61a08ce048d38407a5b60abf660d
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: fbcd40dc67d796d3e31675bd35321282667fe9fa
Original-Change-Id: I765b76f9d7743f6d387470de594fb6eee99e08ca
Original-Signed-off-by: Varadarajan Narayanan <varada@codeaurora.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/357960
Original-Commit-Ready: Kan Yan <kyan@google.com>
Original-Tested-by: Kan Yan <kyan@google.com>
Original-Reviewed-by: Kan Yan <kyan@google.com>
Reviewed-on: https://review.coreboot.org/16051
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
The gsmi_exec() expects the parameter to be a pointer
to the 32-bit register storage of the SMI save state.
The previous code was passing a pointer with the value
obtained from the saved-state -- not a pointer to the
storage of the register value. This bug causes gsmi
to not log events because it's interrogating the
parameter buffer itself as if it were a pointer.
BUG=chrome-os-partner:55932
Change-Id: I37981424f1414edad1456b31cad1b99020d57db6
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16087
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Since RTC is now a Kconfig ensure RTC is selected on the
x86 chipsets which are in Chrome OS devices. This allows
the eventlog to have proper timestamps instead of all
zeros.
BUG=chrome-os-partner:55993
Change-Id: I24ae7d9b3bf43a5791d4dc04aae018ce17fda72b
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/16086
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
List of changes done here in this patch
1. Remove CARD definition from EMMC and SD Card Controller in scs.asl
since _RMV method does not get evaluated while setting up removable
attribute in sysfs in kernel.
"cat /sys/block/mmcblk1/removable" this command always returns 0.
This CARD Device includes _ADR which follows SDIO Bus format. But,
SD/EMMC sits on PCI Bus.
Hence this CARD Device specific _ADR code is also not needed.
2. Remove Base Address for ACPI debug output memory buffer in
systemagent.asl as it is not getting used throughout the code.
BUG=none
BRANCH=none
TEST=Build and boot kunimitsu
Change-Id: I29effaffdafcc21e26445ec3c54aedecdbc50274
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/16068
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Program PIRQ Routing with correct values, as done by FSP, and also in
'soc/intel/skylake/romstage/pch.c' file. If not done, these values get
overridden by "0" during PxRC -> PIRQ programming in ramstage, in
'soc/intel/skylake/lpc.c' file pch_pirq_init()function.
BUG=none
BRANCH=none
TEST=Build and boot kunimitsu
Change-Id: Ibeb9a64824a71c253e45d6a1c6088abd737cf046
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/16044
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Here is the list of items of code cleanup
1. Define TCO registers in smbus.h and not in pmc.h (as per EDS).
2. Include smbus.h wherever these TCO register defines were used.
3. Remove duplication of define in gpio_defs.h.
4. Remove unnecessary console.h include from memmap.h as no prints done.
5. Remove unnecessary comment from pch.c.
BUG=none
BRANCH=none
TEST=Built and boot kunimitsu.
Change-Id: Ibe6d2537ddde3c1c7f8ea5ada1bfaa9be79c0e3b
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/16027
Tested-by: build bot (Jenkins)
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Adding kabylake device ids for chip inits.
Skylake and Kabylak do not differ much, the intention
is to support both SoCs in the same code base.
Change-Id: I9ff4c6ca08fe681798001ce81cca2c085ce32325
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/16049
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Add missing breaks in reg_access.c.
TEST=Build and run on Galileo Gen2
Found-by: Converity Scan #1361261
Change-Id: I8be57f0758e5918a605e20ab9002747e0cc958e0
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/16069
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Add the bootblock_c_entry routine to make it more explicit where the
code transitions from assembler to C.
TEST=Build and run on Galileo Gen2
Change-Id: Ib5f580c30b58d3c82fedddf63c368e617d401515
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/16064
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Change the debug output levels for quark:
* Remove excess debug output
* Change BIOS_DEBUG to BIOS_SPEW - exception in report_platform.c
TEST=Build and run on Galileo Gen2
Change-Id: I37d7ed21a7fc4c92efeb5b71dd01922d7d4b9192
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/16006
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Disable FSP output when CONFIG_DEFAULT_CONSOLE_LOGLEVEL is not set to 8
(BIOS_SPEW). Use the console log level to choose between the serial
port address and NULL and pass it to FSP for the serial port address.
TEST=Build and run on Galileo Gen2.
Change-Id: I5498aad218524c211082d85d0ae9aacaf08a80f6
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/16005
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Add the pieces necessary to successfully build and run romstage using
the FSP 2.0 build. Because romstage is using postcar, add the postcar
pieces so that romstage can attempt to load postcar.
TEST=Build and run on Galileo Gen2
Change-Id: I66b3437e3c7840223535f6ab643599c9e4924968
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/15866
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Add the pieces necessary to successfully build and run bootblock using
the FSP 2.0 build.
TEST=Build and run bootblock on Galileo Gen2
Change-Id: I2377f0b0147196f100396b8cd7eaca8f92d6932f
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/15865
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Wake status is calculated from the four pairs of gpe0 in
cbmem CBMEM_ID_POWER_STATE which is filled very early
in romstage and depends on the routing information in
PMC GPE_CFG register. Coreboot sets the proper value
of routing based on devicetree from pmc_init. But when
system goes to S3 on waking up PMC is writing default
values again in GPE_CFG which results in returning
wrong wake status in _SWS. This patch corrects that
behaviour by correcting the gpe0 pairs in cbmem after
PMC sets the routing table in resume path.
BUG=chrome-os-partner:54876
TEST=On resume through powerbtn, lidopen, keyboard press, etc.
we are getting proper wake status.
Change-Id: I5942d5c20d8c6aef73468dc611190bb7c49c7c7a
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/16040
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
For the gpio based irq to work, the ownership of the pad
should be changed to GPIO_DRIVER.
Provide an option in the gpio defs to configure the PAD onwership.
BUG=chrome-os-partner:54371
TEST=none
Change-Id: I26d242d25d2034049340adf526045308fcdebbc0
Signed-off-by: Jagadish Krishnamoorthy <jagadish.krishnamoorthy@intel.com>
Reviewed-on: https://review.coreboot.org/15871
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
This corrects the address of the I2C5 Device. The I2C
Controller #5 is on PCI Bus 0: Device 25: Function 1. The ACPI
Address Encoding Logic is - High word = Device #.
Low word = Function #.
So, I2C5 (_ADR) = 0x0019 0001.
BUG=none
BRANCH=none
TEST=Build and boot kunimitsu
Change-Id: I4719a843260ef58cc2307e909e9ccbffea519177
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/16048
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
EVT1 has two board IDs.
Use binary first mode of base3 encoding for board ID.
BUG=chrome-os-partner:55320
TEST=None.
BRANCH=None
Change-Id: I1cac1f74207f42616111d39db5c0494b7d1a0fb2
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 2b16cc74c4c147315b7db345678bbaf536ab4a7b
Original-Change-Id: I6e95c7be4a6d28a0aae38b0838bd2ab71d288ba1
Original-Signed-off-by: Kan Yan <kyan@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/364623
Original-Reviewed-by: David Hendricks <dhendrix@chromium.org>
Original-Reviewed-by: Suresh Rajashekara <sureshraj@chromium.org>
Reviewed-on: https://review.coreboot.org/16030
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins)
Coming Kevin revisions will switch back to an I2C TPM. This patch adds
the required configuration options and code to support that. Since the
TPM type can currently only be changed at compile time, we can no longer
support older Kevins with the same image. In order to build for Kevin
revisions < 5, you have to explicitly override the CONFIG_GRU_HAS_TPM2.
BRANCH=None
BUG=chrome-os-partner:55523
TEST=Compiled both Kevin and Gru, confirmed that bootblock and verstage
binary had the appropriate code differences.
Change-Id: I1b2abe0f331eb103eb0a84f773ee7521d31ae5d8
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 3245bff937154f0f9f39894de9c98a75631d59d9
Original-Change-Id: I81a15c9fb037a7ca2d69818e46cbb4f9a5ae1989
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/364222
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-on: https://review.coreboot.org/16029
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins)
Add support to access CR0 and CR4.
TEST=Build and run on Galileo Gen2.
Change-Id: I8084b7824ae9fbcd55e11a7b5eec142591a7e279
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/16004
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Add the FSP 2.0 header files for Quark. These files were run through
the drivers/intel/fsp2_0/header_util to convert the data types so that
they are compatible with the coreboot build system.
TEST=Build and run on Galileo Gen2.
Change-Id: I15548888215cc811fa753d30b65e3a19e3f8ff8d
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/15863
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Split the original contents of romstage.c into car.c, romstage.c and
fsp1_1.c.
TEST=Build and run on Galileo Gen2
Change-Id: I6392d7382e383ea2087afa6bf45b1f087ba78d79
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/15862
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Initialize the MTRRs for use by bootblock and romstage.
Display the MTRRs.
TEST=Build and run on Galileo Gen2.
Change-Id: Ib1d422c738820163f54771c65034ae77301237ec
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/15861
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Include assert.h to use coreboot's ASSERT macro.
Replace the use of UINT32 data type with uint32_t.
Replace the use of UINT8 data type with uint8_t.
TEST=Build and run on Galileo Gen2
Change-Id: I0bb7e43ea570f7b20355c5d05675ebf593942e83
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/15858
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Create DMAR table for Broadwell-DE SoC.
TEST=Booted MC BDX1 into lubuntu15, dumped ACPI tables with acpidump and
disassembled DMAR table using iasl. The table contents are as
expected and the kernel loads DMAR table without errors.
Change-Id: I7933ba4f5f0539a50f2ab9a5571e502c84873ec6
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/15913
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Relocate ramstage into CBMEM.
TEST=Build and run on Galileo Gen2
Change-Id: I38861f2af4b7b976c7ebb7226d81242f950981e3
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/15994
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Other SOC platforms need to handle the FspNotify calls in the same way
as Apollo Lake. Migrate the FspNotify calls into the FSP 2.0 driver.
Provide a platform callback to handle anything else that needs to be
done after the FspNotify call.
Display the MTRRs before the first call to fsp_notify.
TEST=Build and run on Galileo Gen2
Change-Id: I1ff327d77516d4ea212740c16c2514c2908758a2
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/15855
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Move all FSP error handling into the FSP 2.0 driver. This removes the
need to implement error handling within the SOC code.
TEST=Build and run on Galileo Gen2
Change-Id: I4d548b4c90d369d3857c24f50f93e7db7e9d3028
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/15853
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
per hw team's check and info from EDS, this pin needs to be pu 20K.
Otherwise SoC may not notice interrupt request from
EC over LPC because SERIRQ line is floating.
BUG=chrome-os-partner:55586
BRANCH=none
TEST=boot ok and Quanta factory verified the keyboard issue is gone
Signed-off-by: Kane Chen <kane.chen@intel.com>
Change-Id: I5b0213514ce152d4e2cecdda8786925495a0f24a
Reviewed-on: https://review.coreboot.org/15951
Tested-by: build bot (Jenkins)
Reviewed-by: Freddy Paul <freddy.paul@intel.com>
Reviewed-by: Andrey Petrov <andrey.petrov@intel.com>
IO Standby State (IOSSTATE): The I/O Standby State defines
which state the pad should be parked in when the I/O is in a
standby state. Iosstate set to 15 means IO-Standby is ignored
for this pin (same as functional mode), So that pin keeps on
functioning in S3/S0iX.
Change-Id: Ie51ff86a2ea63fa6535407fcc2df7a137ee43e8b
Signed-off-by: Venkateswarlu Vinjamuri <venkateswarlu.v.vinjamuri@intel.com>
Signed-off-by: Shankar, Vaibhav <vaibhav.shankar@intel.com>
Reviewed-on: https://review.coreboot.org/15776
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Upper CMOS bank is used to store the boot count. It is important to
enable it as soon as possible in bootblock.
BUG=chrome-os-partner:55473
Change-Id: I7c4f49c337c2e24a93c1e71466e2f66db04be562
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/15998
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
1. skylake does not support UART over I/O. So, NO_UART_ON_SUPERIO needs
to be selected by default.
2. Move BOOTBLOCK_CONSOLE under UART_DEBUG.
3. Include bootblock/uart.c only if UART_DEBUG is selected.
Change-Id: I4e996bea2a25b3b1dfb9625d97985a9d3473561b
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/16025
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Without this patch, eDP output is non-functional pre-graphics driver
regardless of payload (SeaBIOS, Tianocore) or video init method
(VBIOS, GOP driver) and once the standard Windows Intel HD graphics
driver is loaded.
Test: Boot Windows on peppy and auron_paine, install Intel HD
Graphics driver, observe functional eDP output with full video
acceleration.
Debugging method: adjust location of call to run VBIOS within
coreboot, observed that eDP output functional if the VBIOS is run
before the power optimizer lines, broken if run afterwards.
Change-Id: I6d8252e3de396887c84533e355f41693b9ea7514
Signed-off-by: Prabal Saha <coolstarorganization@gmail.com>
Reviewed-on: https://review.coreboot.org/15261
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Select HAVE_HARD_RESET in the KCONFIG file to enable use of the
hard_reset routine.
TEST=Build and run on Galileo Gen2
Change-Id: Ib11a80b64cf1c55aec24f2576d197da9017b9751
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/15992
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Fix build error caused by macro substitution in the function definition
when the Kconfig value HAVE_HARD_RESET is not selected.
src/soc/intel/common/reset.c:36:21: error: macro "hard_reset" passed 1 arguments, but takes just 0
void hard_reset(void)
^
src/soc/intel/common/reset.c:37:1: error: expected '=', ',', ';', 'asm' or '__attribute__' before '{' token
{
^
make: *** [build/bootblock/soc/intel/common/reset.o] Error 1
TEST=Build and run on Galileo Gen2
Change-Id: I793570e62a0e46cca86cc540c243e363896ceac7
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/15988
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Update Makefile.inc to allow MTRR display during bootblock and postcar.
TEST=Build and run on Galileo Gen2
Change-Id: If12896df46b9edfc9fff3fab3a12d2dae23517a3
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/15990
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Change routine name from car_state_entry to car_stage_entry.
TEST=Build and run on Galileo Gen2
Change-Id: Ifd11db3fa711f2fe52ade1c6cde94f9be1f3a652
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/15857
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Testing for "devfn < 0" on an unsigned doesn't work, and i2c_bus_to_devfn
returns an int (with -1 for "error"), so use int for devfn.
Change-Id: I7d1cdb6af4140f7dc322141c0c018d8418627434
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Found-by: Coverity Scan #1357450, #1357449
Reviewed-on: https://review.coreboot.org/15964
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The bootblock gets slightly too big, so adjust the space assigned to
it.
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
BUG=none
BRANCH=none
TEST=emerge-nyan coreboot works again.
Change-Id: Ib44d98692ae88c7cd3610c8e643d7d48ac858161
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 4b9038b018ed7a26fbce01d982b22166b328de37
Original-Change-Id: If494e49fb60c11e01ca780c84036ebf24459628c
Original-Reviewed-on: https://chromium-review.googlesource.com/346492
Original-Reviewed-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Queue: Stefan Reinauer <reinauer@google.com>
Original-Tested-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: https://review.coreboot.org/15950
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This removes the newlines from all files found by the new
int-015-final-newlines script.
Change-Id: I65b6d5b403fe3fa30b7ac11958cc0f9880704ed7
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/15975
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Use the ACPI generator for creating the Chrome OS gpio
package. Each mainboard has its own list of Chrome OS
gpios that are fed into a helper to generate the ACPI
external OIPG package. Additionally, the common
chromeos.asl is now conditionally included based on
CONFIG_CHROMEOS.
Change-Id: I1d3d951964374a9d43521879d4c265fa513920d2
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/15909
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
1. Enable SoC SD_CMD/D* signals pull-down of 20k when SD-card
is removed. When SD-card is disconnected, the pull-down is
disabled.
2. Provide path for weak leakage from buffers of SD_CMD/D* signal
to be grounded. Thus dropping voltage on the SD_CMD/D* signals to ~0V.
BUG=chrome-os-partner:54421
TEST=no power leakage when SDCard isn't inserted on skylake platform
Change-Id: I567199b172841125f8916a61a76005cfdaa62eb8
Signed-off-by: Zhuo-hao.Lee <zhuo-hao.lee@intel.com>
Reviewed-on: https://review.coreboot.org/15910
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Do not pass VBT table to fsp in normal mode and S3 resume so that
PEIM GFX will not get initialized.
Change-Id: Iab7be3cceb0f80ae0273940b36fdd9c41bdb121e
Signed-off-by: Abhay Kumar <abhay.kumar@intel.com>
Reviewed-on: https://review.coreboot.org/14575
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
When enabling the controller ODT, the controller vref needs to
correspond with the ODT value and DQ drive strength.
BRANCH=none
BUG=chrome-os-partner:54871
TEST=run "stressapptest -M 1024 -s 1000" on kevin board and pass
Original-Commit-Id: a7251c72b87d9f149b68d086c3252f1c668e0e80
Original-Change-Id: I7e54b3473f68a382208a0fb0b0600552fe6390ad
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/358762
Original-Commit-Ready: Dan Shi <dshi@chromium.org>
Original-Tested-by: Caesar Wang <wxt@rock-chips.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Squashed with:
rockchip/rk3399: Halt if we get an invalid odt or drv value
When we were pushing the updated sdram.c to coreboot.org, the compiler
there found that we were not initializing vref_value_dq in all code
possible code paths.
This patch updates those code paths to halt the system.
Branch=none
Bug=none
Test=Built with coreboot.org toolchain and verified that the compile
errors were gone.
Change-Id: I0ad4207dc976236d64b6cdda58d10bcfbe1fde11
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/362726
Reviewed-by: Julius Werner <jwerner@chromium.org>
Change-Id: I22a0cef6f12d9aae2ea4dcb99e7ebdd788f2cdd1
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/15812
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Add new UPDs for Fspm and Fsps. Update headers to make new UPDs
available for use. New UPDs enable various memory and trace funtionality
options as well as support for zero sized IBB region.
BUG=chrome-os-partner:55513
BRANCH=none
TEST=built and tested with no regressions
Change-Id: Id1573baaa306ed4fe4353df5f27e5963cb1a76e6
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/15815
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This patch updates dptf variable in gnvs based on device
configuration by reading the device tree structure.
BUG=chrome-os-partner:53096
TEST=Verify that the thermal zones are enumerated
under /sys/class/thermal in Amenia and Reef board.
Navigate to /sys/class/thermal, and verify that a
thermal zone of type TCPU exists there.
Change-Id: I8ab34cdc94d8cdc840b02347569a9f07688e92cd
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/15620
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch adds apollolake soc specific change. DPTF
ASL files are now in src/soc/intel/common so that
they can be reused but different soc can have different values
e.g., for skylake cpu soc thermal reporting device is at
Bus 0, Device 4, Function 0 while for apollolake it is Bus 0, Device 0,
Function 1. This patch adds a dptf asl file in soc directory where we
can define all values which can change across soc's and can be
included in mainboard dptf asl.
BUG=chrome-os-partner:53096
TEST=In Amenia and Reef board verify that the thermal zones are
enumerated under /sys/class/thermal in Amenia and Reef board.
Navigate to /sys/class/thermal, and verify that a thermal
zone of type TCPU exists there.
Change-Id: I888260a9c799d36512411a769f26dd30cf8d5788
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/15619
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
This patch adds the common ASL code for Intel
platforms. This is the basic ASL needed to add support
for DPTF controlled devices. We are moving
these commmon ASL files to src/soc/intel/common/acpi as
these are same codes used in all Intel platforms and
hence no need to duplicate.
BUG=chrome-os-partner:53096
TEST=Verify that the thermal zones are enumerated
under /sys/class/thermal. Navigate to
/sys/class/thermal, and verify that a thermal
zone of type TCPU exists there.
Change-Id: I01078382a9008263c6ad99f6bf07558885af6a63
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/15093
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Including the terminating null, 17 characters were being written to the
field, overwriting the a byte of the size field.
Fortunately, the size was updated soon after this.
Fixes coverity warning 1229570 - Destination buffer too small.
Change-Id: I39285a9283dd9a17d638afe5b2755c7e420d7698
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/15889
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
List of activity performing in this patch
- early PCH programming
- early SA programming
- early CPU programming
- mainborad early gpio programming for UART and SPI
- car setup
- move chipset programming from verstage to post console
BUG=chrome-os-partner:55357
BRANCH=none
TEST=Built and booted kunimitsu till POST code 0x34
Change-Id: If20ab869de62cd4439f3f014f9362ccbec38e143
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Signed-off-by: Naveen Krishna Chatradhi <naveenkrishna.ch@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/15785
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
With VBOOT_VERIFY_FIRMWARE separated from CHROMEOS, move recovery and
developer mode check functions to vboot. Thus, get rid of the
BOOTMODE_STRAPS option which controlled these functions under src/lib.
BUG=chrome-os-partner:55639
Change-Id: Ia2571026ce8976856add01095cc6be415d2be22e
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/15868
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
VBOOT_VERIFY_FIRMWARE should be independent of CHROMEOS. This allows use
of verified boot library without having to stick to CHROMEOS.
BUG=chrome-os-partner:55639
Change-Id: Ia2c328712caedd230ab295b8a613e3c1ed1532d9
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/15867
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Currently, coreboot performs an erase of the entire MRC cache region on
flash if there is a version mismatch for the MRC data. Instead of doing
that, store the new MRC data in the next available slot, if there is
enough space available in the cache region.
BUG=chrome-os-partner:55699
Change-Id: Ib24a94f0a47c79941ed9f60095360ae3aad5540b
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/15915
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The monitor/mwait is broken on Apollolake. So use ACPI legacy
mwait IO redirection as a work around
BUG=chrome-os-partner:55110
Change-Id: I2e1834130d9586b4310466d3549d19bf427ffe24
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/15890
Tested-by: build bot (Jenkins)
Reviewed-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Quark does not support the rdmsr and wrmsr instructions. In this case
use a SOC specific routine to support the setting of the MTRRs. Migrate
the code from FSP 1.1 to be x86 CPU common.
Since all rdmsr/wrmsr accesses are being converted, fix the build
failure for quark in lib/reg_script.c. Move the soc_msr_x routines and
their depencies from romstage/mtrr.c to reg_access.c.
TEST=Build and run on Galileo Gen2
Change-Id: Ibc68e696d8066fbe2322f446d8c983d3f86052ea
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/15839
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
All mainboards (nyans) utilizing the cache_policy option
has it set to DCACHE_WRITETHROUGH. This option is for setting
the framebuffer's cache attribute. However, this option is
reliant on an architecture-specific enumeration. Just remove
the option and use DCACHE_WRITETHROUGH across the board. If
someone wants to reconfigure it at a later date one can
introduce a non-architecture specific option.
Change-Id: I6a0848231f5e28d36ec2d56b239bed67619fe5a7
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/15838
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
We set this driving control to prevent signal attenuation caused by
LVDS DRV termination.
When DA_LVDSTX_PWR_ON is not set, LVSH has no power and LVDS DRV
termination status is unknown (floating). This creates a chance that
MIPI output would be influenced. The DSI's LP signal will be half
voltage attenuation. There will be no display on panel.
When DA_LVDSTX_PWR_ON is set, LVSH and LVDS DRV termination are
effective and termination is fixed OFF. The DSI won't be influenced.
We only need to set this register once, so we set it here to prevent
repeatedly setting in the kernel when the system goes to recovery mode.
BUG=chrome-os-partner:55296
BRANCH=none
TEST=build pass elm and show ui
Change-Id: Ie3ccf6fb611dd5a1e2c02b7825d42a92e61268c0
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 0d25a27f300acc4b65a894110d3ee0cc9676cd12
Original-Change-Id: Ie71f9cc41924787be8539c576392034320b57a49
Original-Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/360850
Original-Commit-Ready: jitao shi <jitao.shi@mediatek.com>
Original-Tested-by: jitao shi <jitao.shi@mediatek.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/15807
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This allows the board to save the recovery request in case of unexpected
reboots caused by FSP.
With recovery module in vboot handling the saving of recovery reason
across reboots, there is no need to have special fsp reset handling
under soc.
BUG=chrome-os-partner:55431
Change-Id: I0b7ce14868a322072d3e60c1dae43f211b43fdbf
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/15804
Tested-by: build bot (Jenkins)
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This allows the board to save the recovery request in case of unexpected
reboots caused by FSP.
BUG=chrome-os-partner:55431
Change-Id: If71802d2cba52a426f4c2db90d6c5384ed03ce68
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/15803
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
As shown in testing, if CA use 34.3ohms drive strength, it leads
to an overshoot. To fix this, change the drive strength to 48 ohms.
BRANCH=none
BUG=chrome-os-partner:54871
TEST=run "stressapptest -M 1024 -s 1000" on kevin board and pass
Change-Id: I8666474fc18391da14a3338611f962f2f08f36d0
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: fbc1c13f9ab808fc907b2e3f9bde1d09f92980f1
Original-Change-Id: I231f5b1bd45ff262686fbacbaf119a8a57fad27b
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/358761
Original-Commit-Ready: Dan Shi <dshi@chromium.org>
Original-Tested-by: Caesar Wang <wxt@rock-chips.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/15811
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Fix the board ID handling.
Recovery switch and WP status GPIO has been reassigned in board rev3.
Configure related GPIOs based on Board ID.
BUG=chrome-os-partner:55320
TEST=Verified GPIO assignment for Rev.1 board.
BRANCH=None
Change-Id: Id8e1ba1c039f8b5b503f0da038e5cfc84b72678f
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: d295ab514e31d9ebd1b77e0af9b769e64cbf567e
Original-Change-Id: I6d3d5df2e9017f7845edc3cd0b2c19ad7c58a97c
Original-Signed-off-by: Kan Yan <kyan@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/361393
Original-Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: https://review.coreboot.org/15809
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
1. Remove unused functions/structures.
2. Add checks for NULL return values.
3. Change prefixes to vb2 instead of vboot for functions used internally
within vboot2/
4. Get rid of vboot_handoff.h file and move the structure definition to
vboot_common.h
5. Rename all functions using handoff structure to have prefix
vboot_handoff_*. All the handoff functions can be run _only_ after cbmem
is online.
6. Organize vboot_common.h content according to different
functionalities.
BUG=chrome-os-partner:55431
Change-Id: I4c07d50327d88cddbdfbb0b6f82c264e2b8620eb
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/15799
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
All the mainboards share the same config options for CHROMEOS. Instead
of duplicating those in every mainboard, move the CHROMEOS config to SoC
and make it dependent on MAINBOARD_HAS_CHROMEOS.
BUG=chrome-os-partner:55431
Change-Id: Iafabb6373dfe16aaf0fe2cbc4e978952adeb403e
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/15822
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
All the mainboards share the same config options for CHROMEOS. Instead
of duplicating those in every mainboard, move the CHROMEOS config to SoC
and make it dependent on MAINBOARD_HAS_CHROMEOS.
BUG=chrome-os-partner:55431
Change-Id: I2d54ff6beac9fca7596a8f104e3c1447cada5c05
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/15821
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
The controller for device mode USB is not plan of record
on apollolake. However, one still needs to configure the
one port to be host mode by default such that the devices
work as expected when plugged into the board.
BUG=chrome-os-partner:54581,chrome-os-partner:54656
TEST=Enabled xdci controller. Used USB type C->A dongle to
check that a mass storage device worked on port 0 on
reef.
Change-Id: Ia9ec5076491f31bc5dc3d534e235fb49f7b2efac
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/15781
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
The gpio bank irq is not correct and hence gpio
bank handler is never called in case of gpio based irq.
Correct the gpio bank irq to enable gpio based irq.
BUG=chrome-os-partner:55433
TEST=cat /proc/interrupts | grep INT3452 should
output 14.
Change-Id: I54253786425b7d4c2007043d49a91dfa6db0397b
Signed-off-by: Jagadish Krishnamoorthy <jagadish.krishnamoorthy@intel.com>
Reviewed-on: https://review.coreboot.org/15756
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The 'dram density' is a misnomer because the memory initialization
code treats that input parameter as a per rank density. Therefore,
update the variables to further clarify how it's actually being
used.
BUG=chrome-os-partner:55446
Change-Id: Ie4c944f35b531812205ac0bb1c70f39ac401495e
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/15773
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Despite the UPD comments the Chx_RankEnable fields are a bit
mask which indicates which ranks are enabled for physical
channel. Add the ability to set the rank mask correctly for
dual rank LPDDR4 modules.
BUG=chrome-os-partner:55446
Change-Id: I9dbed7bb6a4b512e57f6b4481180932a7cce91ff
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/15771
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
The reset requests are handled in the FSP 2.0 wrapper, but
the current code doesn't check any non-successful return
values. Provide parity with the memory init path which die()s
under those circumstances.
Change-Id: I9df61323f742b4e94294321e3ca3ab58a68ca4dd
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/15766
Tested-by: build bot (Jenkins)
Reviewed-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Add missing break to LEG_GPIO_REGS case to return the correct value for
legacy GPIO reads. Fixes coverity issue CID 1357460.
Found by Coverity, Fixes:
* CID 1357460 (#1 of 1): Unused value (UNUSED_VALUE)
returned_value: Assigning value from reg_legacy_gpio_read(step->reg)
to value here, but that stored value is overwritten before it can be
used.
value_overwrite: Overwriting previous write to value with value from
reg_pcie_afe_read(step->reg).
TEST=Build and run on Galileo Gen2.
Change-Id: I6c52e8801a32f510ac94276fe0c097850cbfde57
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/15732
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
The 'speed' variable isn't being used after refactoring.
Change-Id: Id27a920c61b2bba18d391a7bfefe570235402dec
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/15749
Tested-by: build bot (Jenkins)
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
FSP 2.0 spec only defines 2 reset request (COLD, WARM) exit codes. The
rest 6 codes are platform-specific and may vary. Modify helper function
so that only basic resets are handled and let SoC deal with the rest.
Change-Id: Ib2f446e0449301407b135933a2088bcffc3ac32a
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/15730
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
At first boot CSE spends long time preparing media for use. As result
it may not be able to deal with a CPU reset. Add reset_prepare()
callback that polls CSE readiness.
BUG=chrome-os-partner:55055
TEST=build with release version of fsp, reboot, observe polling for
CSE, then proper reboot happening
Change-Id: I639ef900b97132f1a7f269bb864d70009df9fdfe
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/15721
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Some Intel SoC may need preparation before reset can be properly
handled. Add callback that chip/soc code can implement.
BUG=chrome-os-partner:55055
Change-Id: I45857838e1a306dbcb9ed262b55e7db88a8944e5
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/15720
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Add functions to read Host Firmware Status register and a helper
function to determine if CSE is ready.
BUG=chrome-os-partner:55055
TEST=none
Change-Id: If511a51c04f7e59427d7952fa67b61060e2be404
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/15713
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The FSPS component loading was just loading to any memory address
listed in the header. That could be anywhere in the address space
including ramstage itself -- let alone corrupting the OS memory on
S3 resume. Remedy this by loading and relocating FSPS into cbmem.
The UEFI 2.4 header files include path are selected to provide the
types necessary for FSP relocation.
BUG=chrome-os-partner:52679
Change-Id: Iaba103190731fc229566a3b0231cf967522040db
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/15742
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-by: John Zhao <john.zhao@intel.com>
The previously implementation for loading the FSPM component didn't
handle platforms which expects FSPM to be XIP. For the non-XIP case,
romstage's address space wasn't fully being checked for overlaps.
Lastly, fixup the API as the range_entry isn't needed any longer.
This API change requires a apollolake to be updated as well.
BUG=chrome-os-partner:52679
Change-Id: I24d0c7d123d12f15a8477e1025bf0901e2d702e7
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/15741
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Instead of performing the same tasks in the chipset code move
the common sequences into the FSP 2.0 driver. This handles the
S3 paths as well as saving and restoring the memory data. The
chipset code can always override the settings if needed.
BUG=chrome-os-partner:52679
Change-Id: I098bf95139a0360f028a50aa50d16d264bede386
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/15739
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
The amount of reserved memory just below the DRAM limit in
32-bit space is defined in the FSP 2.0 specification within
the FSPM_ARCH_UPD structure. There's no need to make the
chipset code set the same value as needed for coreboot.
The chipset code can always change the value if it needs
after the common setting being applied.
Remove the call in soc/intel/apollolake as it's no longer
needed.
BUG=chrome-os-partner:52679
Change-Id: I69a1fee7a7b53c109afd8ee0f03cb8506584d571
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/15738
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Andrey Petrov <andrey.petrov@intel.com>
Fix issue where zero-sized BIOS region could cause bitshift
for '-1' which is an unspecified behavior.
Change-Id: Icb62bf413a1a0d293657503ef21fe97b5f9a5484
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/15727
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Asserting this GPIO will send a signal to the EC to trigger a reset
for the AP and the CR50.
BRANCH=none
BUG=chrome-os-partner:55252
TEST=the device now reboots when it needs to switch between different
boot modes instead of hanging with "failed to reboot" message.
Change-Id: I8d168e313b6983c96c80f7ad6d70bb84c1ec1d9c
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 83a4c8ff68ab24a103f2166e948eb23624ea97f7
Original-Change-Id: Idfd20977cf3682bd8933f89e8eec53005e55864e
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/360238
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/15718
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
Since the Integrated Sensor Hub can be disabled through devicetree.cb
as a PCI device, there is no need for a separate register variable.
Remove handling the register and update mainboards' devicetrees. Also
keep ISH disabled on both Reef and Amenia.
Change-Id: I90dbf57b353ae1b80295ecf39877b10ed21de146
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/15710
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
1. The hotplug feature needs to be disabled
so that pcie root ports will be disabled by fsp
2. Correct PcieRootPortEn mapping.
The correct mapping should be like below
PcieRootPortEn[0] ==> 00:14.0
PcieRootPortEn[1] ==> 00:14.1
PcieRootPortEn[2] ==> 00:13.0
PcieRootPortEn[3] ==> 00:13.1
PcieRootPortEn[4] ==> 00:13.2
PcieRootPortEn[5] ==> 00:13.3
BUG=chrome-os-partner:54288
BRANCH=None
TEST=Checked pcie root port is disabled properly
and make sure pcie ports are coalesced.
Also make sure the device will still be enabled after coalescence
when pcie on function 0 is disabled devicetree
Change-Id: I39c482a0c068ddc2cc573499480c3fe6a52dd5eb
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/15595
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The ramstage main() in lib/hardwaremain.c has the logic
to set the ACPI sleep state based on romstage_handoff. Thus,
there's no need to do it a second time.
Change-Id: I75172083587c8d4457c1466edb88d400f7ef2dd0
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/15662
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
The ramstage main() in lib/hardwaremain.c has the logic
to set the ACPI sleep state based on romstage_handoff. Thus,
there's no need to do it a second time.
Change-Id: I88af301024fd6f868f494a737d2cce14d85f8241
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/15661
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Lee Leahy <leroy.p.leahy@intel.com>
CBMEM should be placed at the top of RAM, which can be found by parsing
the configuration string. Configuration string parsing isn't yet
implemented, so I'll hard-code the CBMEM location for now.
Change-Id: If4092d094a856f6783887c062d6682dd13a73b8f
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/15284
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
rk3399 sdram size is 192K, and there still some unused space.
We need more romstage space to include the sdram config, so extend
the romstage range.
BRANCH=none
BUG=chrome-os-partner:54871
TEST=run "stressapptest -M 1024 -s 1000" on kevin board and pass
Change-Id: Ib827345fe646e985773e6ce3e98ac3f64317fffb
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 626ab15bb4ebb004d5294b948bbdecc77a72a484
Original-Change-Id: Ib5aa1e1b942cde8d9476773f5a84ac70bb830c80
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/359092
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/15660
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
kevin rev3 pwm regulator ripple is still not great, especially for
center logic. To make sdram at 800MHz stable, raise it to 0.95v.
BRANCH=none
BUG=chrome-os-partner:54871
TEST=run "stressapptest -M 1024 -s 1000" on kevin board and pass
Change-Id: If4a15eb7398eea8214cb58422bca7cfb5f4a051a
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: d29bc581effb0008eb196685aa22dd65b5d478a5
Original-Change-Id: Ideec9c3ab2f919af732719ed2f6a702068d99c8f
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/359130
Original-Commit-Ready: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/15659
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
This removes an empty function for sdram training. If it's needed
later, we can always add it back.
BRANCH=none
BUG=none
TEST=build and boot firmware for kevin/gru
Change-Id: Id526ef86cf5044894a1a736cc39f10d32f49c072
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 3e93461b96bfadc08bf0b46cf99052d9cdffa422
Original-Change-Id: I6bf77d2f81719c68cd78722c3fe9ae547ea1e79c
Original-Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/354164
Original-Reviewed-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/15657
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
This simplifies some of the code with better variable declaractions
which removes a lot of line continuations. Instead of declaring a
pointer to the container of the needed struct or array, this retrieves
a pointer to the struct or array instead.
BRANCH=none
BUG=none
TEST=check that gru and kevin still build and boot properly followed
by running "stressapptest -M 1024 -s 1000" and making sure it passes
Change-Id: I34a9be0f35981c03a6b0c27a870981a5f69cecc0
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: 5c17449fcdfbe83ec75a3a006aaf7393c66006b7
Original-Change-Id: If4e386d4029f17d811fa3ce83e5be89e661a7b11
Original-Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/354162
Original-Reviewed-by: Martin Roth <martinroth@chromium.org>
Original-Reviewed-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: https://review.coreboot.org/15655
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
This removes a variable that was only used once and makes variable
declarations consistent by moving those only used in one block of code
into that block.
BRANCH=none
BUG=none
TEST=on kevin/gru, run "stressapptest -M 1024 -s 3600"
Change-Id: Iacfc0ffef34a4953cfb304b8cb4975b045aea585
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: a79bbbc83d0f5cccf6bb4ad44ae2239c7f4b45e3
Original-Change-Id: Id0ff0c45189c292ab40e1c4aa27929fb7780e864
Original-Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/355667
Original-Reviewed-by: Martin Roth <martinroth@chromium.org>
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/15654
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
This adds two local variables for dramtype and ddr_freq to sdram_init
since those two values are commonly used in the function. It also
removes a variable that is just used once and directly uses the value
for a function call instead.
BRANCH=none
BUG=none
TEST=on kevin/gru, run "stressapptest -M 1024 -s 3600" and check that
it passes
Change-Id: I4e9dbc97803ff3300b52a5e1672e7e060af2cc85
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: b7d1135c65298a73e6bf2a4a34b7c9b84f249ea8
Original-Change-Id: I4e1a1a4a8848d0eab07475a336c24bda90b2c9f8
Original-Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/355666
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/15653
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
It is not used in this file.
Change-Id: I59bb41370b97b79073c0fd82b1dbcae9fd8a62d0
Reported-by: GCC 6.1.0
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/15552
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
There is currently a SMBus driver implemented for soc/intel/broadwell
which nearly matches Broadwell-DE as well. Use this driver as template
and add minor modifications to make it work for Broadwell-DE. Support in
romstage is not available and can be added with a different patch.
Change-Id: I64649ceaa298994ee36018f5b2b0f5d49cf7ffd0
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/15617
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
With recent bootblock code additions the CBMEM console buffer is not
large enough to store the entire log accumulated before DRAM is
initialized, spilling 700 bytes or so on the floor.
This patch adds 1 KB to the CBMEM console buffer, at the expense of the
bootblock area in SRAM. The bootblock is taking less then 26K out of
31K allocated for it after this change.
Placing CBMEM console area right after the bootblock makes sure other
memory regions are not going to be affected should memory distribution
between bootblock and CBMEM console need to change again.
BRANCH=none
BUG=none
TEST=examining /sys/firmware/log after device boots up into Chrome OS
does not report truncated console buffer any more.
Change-Id: I016460f57c70dab4d603d4c5dbfc5ffbc6c3554f
Signed-off-by: Martin Roth <martinroth@chromium.org>
Original-Commit-Id: bfa31684a1a9be87f39143cb6c07885a7b2e4843
Original-Change-Id: I2c3d198803e6f083ddd1d8447aa377ebf85484ce
Original-Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/358125
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/15607
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This patch adds the support for gpio_tier1_sci_en bit which
needs to be set before going to sleep so that when
gpio_tier1_sci_sts bit gets set platform can wake
from S3.
BUG = chrome-os-partner:53992
TEST = Platform wakes from S3 on lidopen,key press.
Tested on Amenia and Reef boards.
Change-Id: I3ba79fa53ca8817149d585fa795a8f427c128dcb
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/15612
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
FSP is currently setting a hard-coded policy for the interrupt
polarity settings. When the mainboard has already set the GPIO
settings up prior to SiliconInit being called that results
in the previous settings being dropped. Work around FSP's
default policy until FSP is fixed.
BUG=chrome-os-partner:54955
Change-Id: Ibbd8c4894d8fbce479aeb73aa775b67df15dae85
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/15649
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
For APIC routed gpios, set the corresponding interrupt polarity
for the associated IRQ based on the gpio pad's invert setting.
This allows for the APIC redirection entries to match the hardware
active polarity once the double inversion takes place to meet
apollolake interrupt triggering constraints.
BUG=chrome-os-partner:54955
Change-Id: I69c395b6f861946d4774a4206cf8f5f721c6f5f4
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/15648
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The interrupt and timer subsystem (ITSS) sits between the APIC
and the other logic blocks. It only supports positive polarity
events, but there's a polarity inversion setting for each IRQ such
that it can pass the signal on to the APIC according to the
expected APIC redirection entry values. This support is needed
in order for the platform/board to set the expected interrupt
polarity into the APIC for gpio signals.
BUG=chrome-os-partner:54955
Change-Id: I50ea1b7c4a7601e760878af515518cc0e808c0d1
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/15647
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Internally, apollolake routes its interrupts as active high.
This includes SCI, SMI, and ACPI. Therefore, provide helper
macros such that the user can describe an interrupt's active
high/low polarity more easily. It helps for readability when
one is comparing gpio configuration next to APIC configuration
in different files. Additionally, the gpio APIC macros always
use a LEVEL trigger in order to let the APIC handle the
filtering of the IRQ on its own end.
BUG=chrome-os-partner:54977
Change-Id: Id8fdcd98f0920936cd2b1a687fd8fa07bce9a614
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/15644
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Andrey Petrov <andrey.petrov@intel.com>
Aaron Durbin