all boards to the new config scheme.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6421 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
actual SIO. This fixes the serial device being disabled during PNP
init.
Signed-off-by: Marc Jones <marcj303@gmail.com>
Acked-by: Scott Duplichan <scott@notabs.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6400 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6384 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
A video option rom must be added for UMA graphics support. It can
be extracted from the supplied UEFI BIOS.
ASRock E350M1 support is based on the AMD persimmon project. The
major differences are SIO model and DIMM SDP addressing. With this
coreboot and seabios, the board can boot DOS from a SATA drive and
can boot WinPE from a USB flash drive. I was unable to get
Windows setup to run.
The board has a socketed SPI flash BIOS chip and a serial port
header. The SIO is Nuvoton NCT5572D. Using coreboot's existing
Winbond w83627hf is a good enough match to get the serial port
and keyboard working.
Signed-off-by: Scott Duplichan <scott@notabs.org>
Acked-by: Peter Stuge <peter@stuge.se>
Acked-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6382 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The southbridge already provides hard_reset.
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Acked-by: Patrick Georgi <patrick.georgi@secunet.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6378 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The current code works only with dual channel if Channel 0 uses SPD address
0x50/0x51, while the second channel has to use 0x52/0x53.
For hardware that uses other addresses (like the ThinkPad X60) this means we
get only one module running instead of both.
This patch adds a second parameter to sdram_initialize, which is an array with
2 * DIMM_SOCKETS members. It should contain the SPD addresses for every single
DIMM socket. If NULL is given as the second parameter, the code uses the old
addressing scheme.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6374 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
It currently supports:
- Sleepbutton
- AC state
- Battery state
- Interrupt routing
- Display Brightness control
- Hotkeys
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6368 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
It is incorrect, and will be replaced with proper ACPI for X60.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6364 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Fixes abuild issues.
Signed-off-by: Marc Jones <marcj303@gmail.com>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6363 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Adds support for Lenovo X60 series ThinkPads. So far, only X60s
(Model 1703) has been tested.
It's a basic patch without SMI and ACPI, as this makes it easier to
review. SMI and ACPI patches will follow.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6360 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6353 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This code provides support for IBASE Technology DB-FT1 (AMD code name Persimmon) and AMD Inagua platforms. It is dependent on all other patches in this set.
Signed-off-by: Frank Vibrans <frank.vibrans@amd.com>
Acked-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6352 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Adds a new src/ec subdir for embedded controllers (mostly found in laptops)
and converts Getac P470 and Roda RK886EX to use the new ACPI EC instead
of having their own copies of those functions.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6304 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
smm-y wasn't required before, because udelay.c used to be #included from
various files in src/mainboard.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Patrick Georgi <patrick.georgi@secunet.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6303 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
LPT port. With the CMOS variable set, LPT is found by SeaBIOS,
with the variable reset, it's not.
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Acked-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6302 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
the board. I thought we did this ages ago.
Also push CAR BASE further down so it won't conflict with a 32mbit flash part.
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Acked-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6299 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Note:
1. bimini_fam10/Kconfig: Set GENERATE_MP_TABLE in Kconfig. This will make sure the
smp_write_config_table will run. Then intr_data will be written
into 0xC00/0xC01.
2. bootblock: Use PCI_DEV(0, 0x14, 3) instead of
pci_locate_device(PCI_ID(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_SB800_LPC), 0).
The pci_locate_device will cause the system crash.
3. fadt.c: Change fadt revision to 1. 3 will cause the linux hang. Why?
4. early_setup.c: pmio 0x65 has change its meaning.
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Acked-by: Zheng Bao <zheng.bao@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6288 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
board is 2MB and the entry point is somewhere in the middle. quite weird setup
http://www.embeddedarm.com/products/board-detail.php?product=TS-5300
We should probably wipe the board from the tree. It will not work anyways with
current coreboot and the architecture is kind of obscure.
Signed-off-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6287 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6257 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6256 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
on what the GPIOs are used for.
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6254 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
If a file "cmos.default", type "cmos default"(0xaa) is in CBFS,
a wrong checksum leads to coreboot rewriting the first 128 bytes
(except for clock data) with the data in cmos.default, then
reboots the system so every component of coreboot works with the
same set of values.
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6253 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
select the right output device.
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Acked-by: Joseph Smith <joe@settoplinux.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6252 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Correct default ROM image size for this board (512KB is correct).
- devicetree.cb: Add AUX I/O config (mainly GPIO settings).
This allows you to control the LEDs in the front panel and JP900/JP901
can be read.
- irq_tables.c: Rework PIRQ table to make more onboard devices work.
Also, avoid IRQ9.
- mainboard.c: Drop unneeded functions, everything is done in devicetree.cb.
Signed-off-by: Marc Bertens <mbertens@xs4all.nl>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6247 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
We did the same with other chipsets in r6150.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6236 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Move CACHE_AS_RAM_ADDRESS_DEBUG #define to Kconfig, where it was renamed
to HAVE_DEBUG_CAR in r5898.
- Move QRANK_DIMM_SUPPORT to Kconfig, see r6028.
- Drop obsolete/unused COMPRESS, see r6145.
- Drop obsolete SET_NB_CFG_54, see r6086.
- Move SET_FIDVID/SET_FIDVID_CORE_RANGE to Kconfig, see r6077.
Actually, the default for SET_FIDVID_CORE_RANGE is 0, so drop it.
- Rename some GENERATE_* options to HAVE_*, see r6027.
- Drop "select CACHE_AS_RAM", this is now set in the socket, see r6151.
- Drop ACPI_SSDTX_NUM, the global default is 0 already.
- Random whitespace and coding style fixes.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6233 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Kerry She <Kerry.she@amd.com>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6231 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
to FG (FooGlue). As the GX2 has no VIP port.
-Change the Memmory setup MSR register names so they correspond better to the
databook. (Part1)
This is less confusing for beginners.
-Add a MSR printing function to northbridge.c like in the Geode LX code.
-Remove the AES register names.(GX2 has no AES registers)
-Delete some unused code.
-Clean up GX2 northbridge code to match Geode LX code.
-Add missing copyright header to northbridge.c.
-Move hardcoded IRQ defining from northbridge.c to irq_tables.c .
Signed-off-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6221 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The intel/xe7501devkit is still broken, I think the (romcc) image is too big to
fit in the bootblock if CONFIG_DEBUG_RAM_SETUP is enabled. It would make sense
to convert all CPU_INTEL_SOCKET_MPGA604 to CAR, but I have no hardware to test.
Signed-off-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6215 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
allocator. If that does not work out, they should be set in the code. Setting
them in Kconfig is the worst possible thing to do.
Signed-off-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6213 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- nokia/ip530/devicetree.cb, southbridge/ti/pci1x2x/pci1x2x.c:
- Fix SMSC FDC37B787 name (was a typo).
- Disable PS/2 keyboard/mouse LDN, the IP530 doesn't have either.
- Fix typo: s/PCI_DEVICE_ID_TI_1420/PCI_DEVICE_ID_TI_1520/.
- All of these are confirmed by Marc Bertens on IRC.
- Fix a few CHIP_NAME HP board names.
- Random whitespace and coding-style fixes.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6212 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This is needed for all Intel 440BX boards with 4 DIMM slots (such as this one).
Thanks Marc Bertens <mbertens@xs4all.nl> for bringing up the issue and
for the success report for this fix on IRC.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6207 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Hence drop the FALLBACK_ prefix
Signed-off-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6204 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Simple devicetree.cb fix, tested on hardware using a PCI-E x16 graphics card.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6203 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Don't include cmc.bin to the build. It's required, but we don't ship it
- mptable's API changes a bit. Adapt.
- Fix ACPI for new iasl versions with improved code validation
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6199 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
which uses it.
Compiles, but not boot tested lately.
Many things missing (eg. SMM support, proper ACPI, ...)
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6198 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
coreboot made it kind of complicated to print a character on serial. Not quite
as complicated as UEFI, but too much for a good design. Fix it.
Signed-off-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6191 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
We currently use "COREBOOT" unconditionally as the "OEM ID" in our
mptable.c files, and hardcode the mainboard name in mptable.c like this:
mptable_init(mc, "DK8-HTX ", LAPIC_ADDR);
However, the spec says
"OEM ID: A string that identifies the manufacturer of the system hardware."
(Table 4-2, page 42)
so "COREBOOT" doesn't match the spec, we should use the hardware vendor name.
Thus, use CONFIG_MAINBOARD_VENDOR which we have already as the "OEM ID"
(truncate/fill it to 8 characters as per spec).
Also, use CONFIG_MAINBOARD_PART_NUMBER (the board name) as "product ID",
and truncate/fill it to 12 characters as per spec, if needed.
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6183 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Most of the current hda_verb.h files are identical (same MD5 sum) and are
intended for a specific MCP55 board with the Realtek ALC880 audio codec,
which has the vendor/device ID of 0x10ec0880. They were splitted out from the
MCP55 southbridge code and put into board dirs a long time ago (which is
correct, as those settings are indeed board-specific), but they were never
adapted to those boards.
Here's the table of which codec is soldered onto which board, based on
checking the vendor website board spec pages, and the board manuals:
- GIGABYTE GA-M57SLI-S4: Realtek ALC883
- MSI MS-7260: Realtek ALC883
- MSI MS-9652: Realtek ALC888
- MSI MS-9282: Server board, doesn't have audio at all
- Tyan S2912: Server board, doesn't have audio at all
- All Supermicro boards: Server boards, don't have audio at all
- NVIDIA l1_2pvv: No public info to be found, but I assume this was the
original MCP55 eval board for the port and it's probably has the Realtek
ALC880 codec used in the original hda_verb.h.
These are the codec vendor device/IDs involved:
Realtek ALC880: 0x10ec0880
Realtek ALC883: 0x10ec0883
Realtek ALC888: 0x10ec0888
The following files are marked as incorrect / TODO, as the ID of the codec
doesn't match and thus will never get actually used (you'll see
"HDA: no verb!" or similar in the coreboot logs). Even if the ID matched,
the rest of the table would be incorrect anyway because the values are
highly board-specific.
./src/mainboard/gigabyte/m57sli/hda_verb.h
./src/mainboard/msi/ms9652_fam10/hda_verb.h
./src/mainboard/msi/ms9282/hda_verb.h
The following files can be safely dropped as these are server boards and
don't have HD audio (or other audio) at all:
./src/mainboard/supermicro/h8dmr/hda_verb.h
./src/mainboard/supermicro/h8qme_fam10/hda_verb.h
./src/mainboard/supermicro/h8dme/hda_verb.h
./src/mainboard/supermicro/h8dmr_fam10/hda_verb.h
./src/mainboard/tyan/s2912/hda_verb.h
./src/mainboard/tyan/s2912_fam10/hda_verb.h
The following two are correct and can stay:
./src/mainboard/nvidia/l1_2pvv/hda_verb.h
./src/mainboard/getac/p470/hda_verb.h
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6180 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6175 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
and do that only if resume is done.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6174 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Abuild tested. Please check all changes if I did not make any wrong while converting this to bytes.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6171 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This is an AMD K8 + NVIDIA MCP55 + ITE IT8716F mainboard.
It has a working hda_verb.h file for HD audio, and a fanctl.c file is
used to enable the CPU fan (among others) so that we don't kill the
CPU due to excessive heat.
Even though some TODOs remain of course, it works good enough to
successfully boot Linux (e.g. via SeaBIOS).
The full status report is available at:
http://www.coreboot.org/ASUS_M2N-E
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6170 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
[PATCH] SB700 common FADT was not applied to this board because it was in the meanwhile added.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6167 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6165 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
src/arch/x86.
Signed-off-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6161 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Factor out the ROM decode enable functionality into bootblock.c and
handle it via the usual TINY_BOOTBLOCK mechanism.
Use "select TINY_BOOTBLOCK" in the southbridge, not individual boards.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6159 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The files debug.asl, globutil.asl, and statdef.asl are duplicated in
many K8/Fam10h boards. However, they're neither board-specific nor
K8/Fam10h-specific nor AMD-specific, so move them to src/arch/i386/acpi.
debug.asl contains generic chunks for I/O port 0x80 handling, and debug
output over serial port (init COM port, send byte, send string, etc).
globutil.asl contains utility methods for string comparison, string length
and similar stuff.
statdef.asl contains generic ACPI bit definitions / status codes from
the ACPI spec (not board- or chipset-specific).
This patch was mostly generated by:
mkdir src/arch/i386/acpi
svn add src/arch/i386/acpi
svn cp src/mainboard/amd/dbm690t/acpi/debug.asl src/arch/i386/acpi/
svn cp src/mainboard/amd/dbm690t/acpi/globutil.asl src/arch/i386/acpi/
svn cp src/mainboard/amd/dbm690t/acpi/statdef.asl src/arch/i386/acpi/
cd src/mainboard
find . -name debug.asl -exec svn rm {} \;
find . -name globutil.asl -exec svn rm {} \;
find . -name statdef.asl -exec svn rm {} \;
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6156 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
> Definitively a iasl problem, it can't even disassemble it's own
> output back to something equivalent to the input file.
> It seems to be generating Bytecode for the Add where it shouldn't.
Here is a solution using the SSDT.
Unfortunately iasl does not resolve simple arithmetic at compile
time, so we can not use Add(DEFAULT_PMBASE, PCNTRL) in the
Processor statement.
This patch instead dynamically generates the processor statement.
I can't use the speedstep generate_cpu_entries() directly since the
cpu doesn't support speedstep.
For now the code is in the southbridge directory, but maybe it
should go into cpu/intel/ somewhere.
IIRC notebook cpus of the era can already have speedstep, so it
would probably be possible to pair the i82371eb with a
speedstep-capable cpu...
Also, I don't know if multiprocessor boards (abit bp6?) would need
to be handled differently.
Abuild-tested.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6153 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
All K8/Fam10h boards use CAR, so move the "select CACHE_AS_RAM"
into the socket directories, and remove it from the individual boards.
Do the same for Intel CPUs/sockets where all boards use CAR.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6151 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
the prefix was introduced in the early v2 tree many years ago
because our old build system "newconfig" could not handle two files with
the same name in different paths like /path/to/usb.c and
/another/path/to/usb.c correctly. Only one of the files would end up
being compiled into the final image.
Since Kconfig (actually since shortly before we switched to Kconfig) we
don't suffer from that problem anymore. So we could drop the sb700_
prefix from all those filenames (or, the <componentname>_ prefix in general)
- makes it easier to fork off a new chipset
- makes it easier to diff against other chipsets
- storing redundant information in filenames seems wrong
Signed-off-by: <stepan@coresystems.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6150 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
the prefix was introduced in the early v2 tree many years ago
because our old build system "newconfig" could not handle two files with
the same name in different paths like /path/to/usb.c and
/another/path/to/usb.c correctly. Only one of the files would end up
being compiled into the final image.
Since Kconfig (actually since shortly before we switched to Kconfig) we
don't suffer from that problem anymore. So we could drop the sb700_
prefix from all those filenames (or, the <componentname>_ prefix in general)
- makes it easier to fork off a new chipset
- makes it easier to diff against other chipsets
- storing redundant information in filenames seems wrong
Signed-off-by: <stepan@coresystems.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6149 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Use w83627hf_set_clksel_48() where needed instead or open-coding the same
functionality, and also use w83627hf_enable_serial() instead of
w83627hf_enable_dev() (which does exactly the same, but isn't wrapped in the
enter/exit config mode functions).
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6143 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
W83627DHG:
- Add proper "virtual LDN" handling for the LDNs that need it (i.e., those
that don't have their "enable" bit in bit 0 of the 0x30 register).
- Fix various I/O masks in the pnp_dev_info[] array as per
datasheet. Add missing PNP_IRQ0 to the W83627DHG_ACPI LDN.
W83627EHG:
- Similar to W83627DHG, improve the "virtual LDN" setup a bit (it was
mostly implemented already, though).
- Add missing PNP_IRQ0 to the W83627EHG_ACPI LDN.
Also: Fix up devicetree.cb of all boards using W83627DHG/W83627EHG to adapt
for the virtual LDNs.
include/device/pnp.h: Add comment that 'function' (which refers to the
LDN and should probably be renamed later) has to be at least 16 bits
wide. In theory LDNs could use u8, but due to the virtual LDN info being
encoded in the "high byte" of 'function' it must be at least u16.
asrock/939a785gmh/romstage.c: Drop unused GPIO6_DEV.
ibase/mb899/romstage.c: Use DUMMY_DEV instead of a specific LDN (serial
port 1 in this case) to avoid confusion. The global registers
manipulated there are accessible from any LDN.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6140 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6138 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6135 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Single channel (in slot DDR1 and DDR3) produces strange artefacts on screen (and hang)
Dual Channel (in DDR1 and DDR2 aka blue slot) - works nice
All slots populated - same case as Single channel - must be something wrong with UMA.
Tested with 2x 512MB CAS 2.5 DDR400
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6134 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
> Stefan Reinauer wrote:
> > The specified IO port is most likely wrong. As the comment mentions, the
> > SSDT is a good place for that. A preprocessor define used both in the
> > CPU init code and in the asl would solve the problem without an SSDT.
> > For some info on CPU SSDT creation on intel check out
> > src/cpu/intel/speedstep/acpi.c
>
> The IO port is ok (and I wrote the comment myself ;)):
> DEFAULT_PMBASE is 0xe400
> PCNTRL reg offset is 0x10
>
> Using the preprocessor will probably work too if iasl can do simple
> arithmetic (likely yes), I'll look into that.
BTW, my first idea was to use an acpi method that looks up pmbase in
the pci cfg space, but when I define a method like this:
Method(TEST, 2)
{
Return (Add(Arg0, Arg1))
}
I get:
|build/mainboard/asus/p2b/dsdt.ramstage.asl 9: Processor (CPU0,
|0x01, TEST(0xe400, 0x10), 0x06) {}
|Error 4096 - syntax error, unexpected PARSEOP_NAMESEG,
|expecting ')' ^
While using the builtin Add() directly works.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6132 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
I cleaned up the patch and moved most of the dsdt.dsl and
acpi_tables.c into the southbrige/northbridge directory.
Updated patch should fix abuild error and incorporates suggestions
on irc by uwe (thanks for the comments).
Thanks to Idwer Vollering <vidwer@gmail.com> for the original patch.
Tested:
Linux (poweroff, powerbutton event)
XP (poweroff, powerbutton event)
Abuild-tested
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6127 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
In bcm5785_enable_rom(): Use PCI IDs from pci_ids.h instead of hardcoding,
and use 'dev' instead of 'addr' as device_t variable name.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6126 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also, add missing license header to amd8111_enable_rom.c, add some more code
comments and use PCI IDs from pci_ids.h instead of hardcoding.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6124 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also, move CONFIG_HT_CHAIN_END_UNITID_BASE #ifdef block to mcp55.h to make
the build work (but this is a good idea anyway, as it's used in
multiple files).
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6123 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This adds the board-specific parts for S3 support on the M2V board.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6122 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2) the patch implements get_cbmem_toc in chipset specific way if defined.
On Intel targets it should be unchanged. On K8T890 the the cbmem_toc is read from NVRAM. Why you ask? Because we cannot do it as on intel, because the framebuffer might be there making it hard to look for it in memory (and remember we need it so early that everying is uncached)
3) The patch removes hardcoded limits for suspend/resume save area (it was 1MB) on intel. Now it computes right numbers itself.
4) it impelements saving the memory during CAR to reserved range in sane way. First the sysinfo area (CAR data) is copied, then the rest after car is disabled (cached copy is used). I changed bit also the the copy of CAR area is now done uncached for target which I feel is more right.
I think I did not change the Intel suspend/resume behaviour but best would be if someone can test it. Please note this patch was unfinished on my drive since ages and it would be very nice to get it in to prevent bit rotten it again.
Now I feel it is done good way and should not break anything. I did a test with abuild and it seems fine.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6117 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Every board had a slightly different invokation, very often commented out
anyway. We could either decide that this is only to be used by developers
during bringup (and thus added manually to romstage.c and removed before
the board gets committed). This method seems to be preferred from what I
have heard on IRC / mailing list in the past.
Or, we add the ram_check() somewhere globally and allow the user to enable
it via menuconfig (possibly only if EXPERT is selected).
Either way, the current method of spreading the calls all over the place is
not really the way to go.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6115 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6114 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This needlessly complicates the code and increases register pressure on romcc
chipsets. We did the same conversion on i440BX, i830, and others.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6112 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
initializing VGA happens pretty much as the last thing before starting the
payload. Hence, drop VGA console support, as we did in coreboot v3.
- Drop VGA and BTEXT console support.
Console is meant to be debugging only, and by the time graphics comes up
99% of the risky stuff has already happened. Note: This patch does not remove
hardware init but only the actual output functionality.
The ragexl driver needs some extra love, but that's for another day
- factor out die() and post()
- drop some leftover RAMBASE < 0x100000 checks.
Signed-off-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: QingPei Wang<wangqingpei@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6111 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also, remove some less useful comments, some dead code / unused functions.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6108 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also drop some dead or useless code snippets.
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6107 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6106 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6105 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
not brought over to Kconfig (this applies to all #defines to 4, as
that's the default anyway)
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6104 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The (0xa << 3) expression equals 0x50, i.e. DIMM0.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6103 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Except for one instance the spd_addr.h were now very tiny, there's not
much point in keeping that stuff in an extra file. The only user of those
files is the romstage.c file anyway.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6101 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- VIA VT8235: Do the shift in smbus_read_byte() as all other chipsets do.
- spd.h: Move RC00-RC63 #defines here, they were duplicated in lots of
romstage.c files and lots of spd_addr.h files. Don't even bother for
those spd_addr.h which aren't even actually used, drop them right away.
- Replace various 0x50 hardcoded numbers with DIMM0, 0x51 with DIMM1,
and 0xa0 with (DIMM0 << 1) where appropriate.
- Various debug.c files: Replace SMBUS_MEM_DEVICE_START with DIMM0,
SMBUS_MEM_DEVICE_END with DIMM7, and drop useless SMBUS_MEM_DEVICE_INC.
- VIA VX800: Drop unused SMBUS_ADDR_CH* #defines.
- VIA VT8623: Do the shift in smbus_read_byte() as all other chipsets do.
Then, replace 0xa0 (which now becomes 0x50) with DIMM0.
- alix1c/romstage.c, alix2d/romstage.c: Adapt to recent bit shift changes.
- Various files: Drop DIMM_SPD_BASE and/or replace it with DIMM0.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6100 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
addressing scheme to match the rest of the tree
(0x50 instead of 0xa0).
abuild tested.
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6099 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- s/Options.lb/devicetree.cb/
- s/Config.lb/devicetree.cb/
- s/cache_as_ram_auto.c/romstage.c/
- h8dmr_fam10/README: Drop obsolete comment, we have mc_patch_01000086.h in
the tree now.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6095 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6089 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
chipset code (where it belongs)
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6088 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
deselected it, and very likely there won't ever be any
hardware that requires it deselected.
Keep the "selected" code path around, leading to no
functional change.
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Scott Duplichan <scott@notabs.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6086 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6085 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Updated patch with improved comments and small bugfix (use same
value for min and max on io resource).
While adding the area between TOM1 and 4GB to \SB.PCI0._CRS seems to be the
easiest way to get both Linux and Windows happy, it is not quite correct
because reserved areas like APIC, MMCONF etc. ranges need to be excluded.
This is a proof of concept patch for the M2V board that dynamically creates a
ResourceTemplate() containing these in the SSDT and adds a corresponding
PNP0C02 device to the DSDT.
All resources that have IORESOURCE_RESERVE and (IORESOURCE_MEM or IORESOURCE_IO) set
are added.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Added M2V-MX SE too.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6084 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
as an ACPI motherboard resource or it will not enable MMCONFIG
and the extended pcie configuration area will be unaccessible:
This patch adds the IORESOURCE_RESERVE flag to the APIC and MMCONF
resource flags to do this.
I also added a new resource for the mapped bios rom area just below 4GB.
I'm not sure if the choice for the index parameter of new_resource()
is correct though.
Note that the bios rom decode is enabled in
src/southbridge/via/vt8237r/vt8237r_early_smbus.c
for the whole 4MB area (even though the comment says 1MB).
Ruik: I extended the flash range to 16MB (This is what VT8237S can decode)
Remove the MMCONFIG region reserve in the mainboard file (this patch makes it obsolete)
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6083 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
http://tracker.coreboot.org/trac/coreboot/changeset/3953
Note that all corresponding DSDTs only ever check TOM2 against 0.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6082 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CONFIG_PIRQ_ROUTE) so far is the amd cs5530.
Add one for vt8237 too.
Setting up the pci routing is important in case you want to boot DOS,
OSes that don't support ACPI or MP tables and ROMs for add-in storage
controllers may depend on this too.
TODO: Fix the 4 routing links limitation in
src/arch/i386/boot/pirq_routing.c
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6081 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The only difference is that the "G" version is in a Pb-free package, which
is not relevant from a programmer's view.
We keep W83627THG (and drop W83627THF) because:
- The W83627THF had a CIR device / LDN which doesn't actually exist.
- The W83627THF had no GPIO2, GPIO3 LDNs (were commented out).
- The W83627THF didn't use the PNP_MSC0/1 which is needed/used by boards.
This also fixes an issue on MSI MS7135's devicetree.cb:
device pnp 4e.6 off end # XXX keep allocator happy
The line above can be (and is) removed, as it was only needed due to the
incorrect CIR LDN in the W83627THF.
In the iwill/dk8x target: Drop incorrect LDNs 4 and 6, add 0xb.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6080 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6079 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6078 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
make their defaults more obvious.
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6077 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6074 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
For now this is a plain copy of the ASUS A8V-E SE target, I reported
that most of the code also works (sort of) for the ASUS A8V-E Deluxe
a long while ago, see
http://www.coreboot.org/pipermail/coreboot/2008-March/031866.htmlhttp://www.coreboot.org/ASUS_A8V-E_Deluxe
There will be a bunch of changes necessary though (devicetree.cb, mptable.c,
ACPI, etc) which do not apply to the A8V-E SE, so we need an extra target.
Also: Increase ID_SECTION_OFFSET on the VIA K8T890/K8M890 southbridge, as
otherwise there will be build errors if the MAINBOARD_PART_NUMBER string
gets too long (as is the case for "A8V-E Deluxe"). The error is:
ld: section .id loaded at [00000000ffffffd2,00000000ffffffef] overlaps
section .romstrap loaded at [00000000ffffff80,00000000ffffffd3]
(both with stock Debian gcc and with xgcc)
Increase ID_SECTION_OFFSET (default 0x10) to 0x80 as other southbridges do.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6072 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Add a few more comments for the entries, and also change the devicetree.cb
files to the more compact and better readable variant with indentation level
of 2 spaces (instead of random mix of tabs and spaces).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6071 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6070 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
an override function in m2v/mainboard.c
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6069 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The power-on default is 1.95V, set the DDR2 voltage to
standards-conforming 1.8V.
I also measured with a multimeter to confirm this.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6066 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- i3100_early_serial.c:
- Split out enter/exit functions as the other Super I/Os do.
- Make i3100_enable_serial() take a device_t as usual, and convert
it to use the standard pnp_* function instead of open-coding
the same functionality by hand.
- Factor out i3100_configure_uart_clk() from i3100_enable_serial(),
we do the same in various other Super I/Os, e.g. ITE ones.
- Add some #defines for register / bit values and some comments.
- Only functional change: Don't set bit 1 of SIW_CONFIGURATION, it's
marked as "READ ONLY, WRITES IGNORED" in the datasheet.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6058 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
compatible. The extended cmos is accessed differently for AMD
and Intel RTCs. Not sure what if any OS cares about this distinction,
but non-Intel compatible seems like a safer way to report the AMD RTC.
Tested with Win7 on Mahogany_fam10 and kino-780am2-fam10.
Signed-off-by: Scott Duplichan <scott@notabs.org>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6046 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This adds the m2v directory and necessary files to src/mainboards/asus and
adjusts the Kconfig.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6045 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
adjusts the Kconfig.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6044 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Rudolf
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6037 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6036 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
other place, and that defines these symbols itself (and
identical, too). Drop them.
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6034 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
All other uses of these symbols have their own (identical)
definitions.
abuild-tested and trivial
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6031 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Use HAVE_ACPI_TABLES, HAVE_MP_TABLE, and HAVE_PIRQ_TABLE (instead of
GENERATE_*) in the board's Kconfig file, as all other boards do.
- Add missing HAVE_ACPI_TABLES/HAVE_MP_TABLE/HAVE_PIRQ_TABLE to boards
which have the respective files. The only exception: EPIA-M700 doesn't
select ACPI, as it doesn't have dsdt.asl. Added a comment that the user
is supposed to run the 'get_dsdt' script and edit Kconfig afterwards.
- Fix minor warning/error in
src/mainboard/msi/ms9652_fam10/acpi_tables.c,
now that the file is actually used.
- msi/ms9652_fam10: use #include instead of Include() as we usually do
now.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6027 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This is Abuild and boot tested.
Signed-off-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6023 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This is Abuild and boot tested.
Signed-off-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6022 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also, change the GX2 boards to use it.
Add a processor speed setting function in human readable MHz and remove
the useless and broken PLLMSR settings (the processor speed was hardcoded
to 366MHz in pll_reset.c).
Signed-off-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6011 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- via/epia-n/mptable.c
- intel/eagleheights/mptable.c (commented out anyway)
- asus/p2b-d/mptable.c
- asus/p2b-ds/mptable.c
Some files still incorrectly contain some smp_write_ioapic() lines from
the original mptable utility target (Supermicro P4DPE), which has one
IOAPIC in the southbridge (Intel ICH3-S), two IOAPICs contained in
the first P64H2, and two more in the second P64H2, i.e. 5 IOAPICs in total.
However, none of the boards where this chunk of code is present has
multiple IOAPICs (and even if they had, the PCI devices where those are
located would probably be different anyway), so drop the incorrect
mptable.c contents.
Also drop the lines from the mptable utility, so that future mptable.c files
don't incorrectly inherit any of this stuff.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Jonathan Kollasch <jakllsch@kollasch.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6006 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Add "select IOAPIC" in the board's Kconfig file.
- Set CONFIG_MAX_PHYSICAL_CPUS to 2 on the board. There are two
CPU sockets (Slot 1) and each CPU can only have one core, multi-core CPUs
didn't exist in that era (CONFIG_MAX_CPUS was set to 2 already).
- Drop useless/duplicated enable_lapic() call from ASUS P2B-DS's romstage.c,
that function is always called if either CONFIG_SMP and/or CONFIG_IOAPIC
are set.
- Rework ASUS P2B-DS mptable.c to fix a number of things:
- Convert it to use mptable_write_buses() as all mptable.c files should do.
- Fix incorrect IOAPICID (it's 0x11 for the external 82093AA IOAPIC).
- Fix a bunch of hardcoded bus IDs, remove incorrect entries, etc.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6004 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Add enable_intel_82093aa_ioapic() which enables IOAPIC usage in the
Intel 82371EB southbridge (sets the proper chip-select) and sets an
IOAPIC ID.
- We only call enable_intel_82093aa_ioapic() if a board does "select IOAPIC"
as on 82371EB-based boards the IOAPIC is an external chip (not integrated
in the southbridge) and it's only populated on multi-CPU boards.
That is, we cannot unconditionally enable it, only on SMP-capable boards.
- Due to the reason explained above, remove "select IOAPIC" from
src/southbridge/intel/i82371eb/Kconfig, and add it to
src/mainboard/asus/p2b-d/Kconfig.
- Also set CONFIG_MAX_PHYSICAL_CPUS to 2 on ASUS P2B-D. There are two
CPU sockets (Slot 1) and each CPU can only have one core, multi-core CPUs
didn't exist in that era (CONFIG_MAX_CPUS was set to 2 already).
- Drop useless/duplicated enable_lapic() call from ASUS P2B-D's romstage.c,
that function is always called if either CONFIG_SMP and/or CONFIG_IOAPIC
are set.
- Rework ASUS P2B-D mptable.c to fix a number of things:
- Convert it to use mptable_write_buses() as all mptable.c files should do.
- Fix incorrect IOAPICID (it's 0x11 for the external 82093AA IOAPIC).
- Fix a bunch of hardcoded bus IDs, remove incorrect entries, etc.
This is build-tested on ASUS P2B-D, and also boot-tested successfully there.
On Linux I now get two entries in /proc/cpuinfo (where only one appeared
before this patch), i.e. both populated CPUs are found.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5998 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Additionally, make the second SMBus more accessible in romstage.
Signed-off-by: Jonathan Kollasch <jakllsch@kollasch.net>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5994 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
local ints. This is wrong in most coreboot mptables, probably all
generated by util/mptable/mptable.c.
After fixing this now XP can boot in MPS mode on my M2V.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5992 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Jonathan Kollasch <jakllsch@kollasch.net>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5991 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Right now, it breaks the build of bootblock enabled boards
with that chipset.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5990 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Drop sig[], oem[], and productid[] fields in all mptable.c files, no
longer needed. The sig[] is always the same ("PCMP"), the oem[] is
currently also always the same ("COREBOOT"), and productid is being
passed into mptable_init() directly as string now.
- LAPIC_ADDR is passed in as parameter, too. While at the moment it's
always the same value that is passed in, the LAPIC base address could
also be relocated theoretically, so keep it as parameter for now.
- Fix a few productid entries, they were (partially) incorrect:
- DK8S2 (was "DK8X", copypaste)
- 939A785GMH (was "MAHOGANY", copypaste)
- X6DHE-G (was "X6DHE", incomplete board name)
- H8DME-2 (was "H8DMR", copypaste)
- H8QME-2+ (was "H8QME", incomplete board name)
- X6DHE-G2 (was "X6DHE", incomplete board name)
- X6DHR-iG2 (was "X6DHR-iG", incomplete board name)
- GA-M57SLI-S4 (was "M57SLI", incomplete board name)
- KINO-780AM2 (was "KINO", incomplete board name)
- DL145 G1 (was "DL145G1", small fix as per vendor website)
- DL145 G3 (was "TREX", wrong board name)
- DL165 G6 (was "HP DL165 G6", drop vendor)
- S2912 (was "S2895", copypaste)
- VT8454c (was "VIA VT8454C", drop vendor, lower-case "c")
- EPIA-N (was "P4DPE", copypaste)
- pc2500e (was "PC2500", incorrect name)
- S1850 (was "S2850", copy-paste)
- MS-7135 (was "MS7135")
- MS-9282 (was "MS9282")
- MS-9185 (was "MS9185")
- MS-9652 (was "K9ND MS-9652")
- Ultra 40 (was "ultra40")
- E326 (was "E325", copypaste)
- M4A785-M (was "TILAPIA", copypaste)
- P2B-D (was "ASUS P2B-D", drop vendor)
- P2B-DS (was "ASUS P2B-DS", drop vendor)
- Adapt the mptable utility to use mptable_init() too.
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5987 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
FADT revision inconsistent with length.
Revision: 0x1
Length: 0xf4
Expected Length: 0x74
Change the FADT revision from 1 to 3 to match its length and prevent the Windows checked build assert.
Signed-off-by: Scott Duplichan <scott@notabs.org>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5985 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This is consistent with the device tree and the chip actually on the board.
Trivial.
Signed-off-by: Jonathan Kollasch <jakllsch@kollasch.net>
Acked-by: Jonathan Kollasch <jakllsch@kollasch.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5974 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also, update the board that uses this socket to match.
Signed-off-by: Jonathan Kollasch <jakllsch@kollasch.net>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5969 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This is pretty much the same mechanism as in r5929.
- Use 'romstage-y' to turn i82801ax_early_smbus.c and i82801bx_early_smbus.c
into distinct compilation units, and don't #include the files anymore
in romstage.c files.
- Ditto for northbridge/intel/i82810/raminit.c, and
northbridge/intel/i82810/debug.c.
- Add various header files which are now needed, drop unused includes.
- Make functions that need to be visible non-static.
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5951 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Drop "select ROMCC" from the boards, as well as early_mtrr stuff.
- Add "select CACHE_AS_RAM" to socket_PGA370/Kconfig, as well as the
usual DCACHE_RAM_BASE and DCACHE_RAM_SIZE variables.
- In socket_PGA370/Makefile.inc add:
cpu_incs += $(src)/cpu/intel/car/cache_as_ram.inc
- Other smaller related fixes.
Abuild-tested and boot-tested on MSI MS-6178.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5949 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Some mainboards need to disable the power button to avoid turning off
right after being turned on, while other boards ship with a jumper over
the power button and should allow the user to configure the behavior.
This adds infrastructure in the form of four mutually exclusive options
which can be selected in a mainboard Kconfig (power button forced on/off,
and user-controllable with default on/off) and one result bool which
source code can test. (Enable the button or not.)
The options have been implemented in CS5536 code and for all mainboards
which select SOUTHBRIDGE_AMD_CS5536, but should be used also by other
chipsets where applicable. Note that if chipset code uses the result
bool ENABLE_POWER_BUTTON, then every board using that chipset must
select one out of the four control options in order to build.
All touched boards should have unchanged behavior, except
pcengines/alix1c, traverse/geos and lippert/hurricane-lx where the
power button can now be configured by the user.
Build tested for alix1c, alix2d, hurricane-lx and wyse-s50. Confirmed
to work as advertised on alix1c both with button enabled and disabled.
Includes additional traverse/geos changes from Nathan and
lippert/hurricane-lx changes from Jens to correctly use the new
feature on those boards.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Aurelien Guillaume <aurelien@iwi.me>
Acked-by: Nils Jacobs <njacobs8@hetnet.nl>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5948 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
As both ioapic.h and acpi.h define a macro named "NMI", rename one
of them (NMI -> NMIType in acpi.h).
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5943 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The following functions are moved to devices/device_util.c:
- ram_resource()
- tolm_test()
- find_pci_tolm()
There are only two tolm_test() / find_pci_tolm() which differ from the
defaults, one of them can easily be eliminated in a follow-up patch,
maybe even both, but for now keep it simple and only eliminate the majority.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5937 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Use 'romstage-y' to turn i82371eb_early_pm.c and i82371eb_early_smbus.c
into distinct compilation units, and don't #include the files anymore
in romstage.c files.
- Ditto for lib/debug.c, northbridge/intel/i440bx/raminit.c, and
northbridge/intel/i440bx/debug.c.
- Add various header files which are now needed.
- Make functions that need to be visible non-static.
- Drop a remaining "select ROMCC" from a 4440BX board.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Idwer Vollering <vidwer@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5929 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also:
Unfortunately Intel 440BX + 82371AB/EB/MB boards can have their ISA device
on various PCI bus:device.function locations.
Examples we encountered: 00:07.0, 00:04.0, or 00:14.0.
Thus, instead of hardcoding PCI bus:device.function numbers such as
PCI_DEV(0, 7, 0), we now simply find the ISA device via PCI IDs, which
works the same on all boards.
As an additional benefit this patch also gets rid of one .c file include
in romstage.c.
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5918 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Add "select CACHE_AS_RAM" in src/cpu/intel/slot_1/Kconfig.
- Add the following in src/cpu/intel/slot_1/Makefile.inc:
cpu_incs += $(src)/cpu/intel/car/cache_as_ram.inc
- Remove "select ROMCC" from all 440BX board Kconfig files.
- Drop all early_mtrr_init() calls, that's done by CAR code now.
Various small fixes were needed to make it build:
- Drop do_smbus_recv_byte(), do_smbus_send_byte(), do_smbus_write_byte(),
those were never called anyways.
- Remove the "static" from the main() functions in romstage.c files.
- Always call dump_spd_registers() from the 440BX debug.c, but use
"#if CONFIG_DEBUG_RAM_SETUP" to only have that code if RAM debugging
is enabled in menuconfig.
- Drop all "lib/ramtest.c" #includes and ram_check() calls (even if
commented out) from romstage.c's, as we've done for most other boards.
- Add missing #includes or prototypes. Some of the prototypes will be
removed later when we get rid of the #include'd .c files.
Abuild-tested for all boards, and boot-tested on A-Trend ATC-6220.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5917 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- move EHCI_BAR and EHCI_DEBUG_OFFSET to Kconfig to be set by USB debug port enabled southbridges
- drop USB debug code includes from romstage.cs and use romstage-srcs in the build system instead
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5911 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Remove many more .c-includes from i945 based boards.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5910 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The AMD SB700 allows changing the physical USB port to be used as
USB Debug Port, implement support for this.
Also, fix incorrect PCI device of the SB700 EHCI device. Actually, the
SB700 has _two_ EHCI devices (D18:F2 and D19:F2), but for now we only use
D18:F2. Our generic USBDEBUG code cannot handle multiple EHCI PCI devices
currently, AFAICS.
Hook up all SB700 boards to the CONFIG_USBDEBUG_DEFAULT_PORT facility.
Untested, but should work.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5907 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
All these boards define QRANK_DIMM_SUPPORT anyway,
which is probably what was meant.
Signed-off-by: Jonathan Kollasch <jakllsch@kollasch.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5905 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
rename it slightly, make it visible only on relevant northbridges,
drop it entirely from via boards (as they seem to have picked it
up from AMD code without using it themselves), and make it
default to false for all boards.
Some romstages used to set this to "true" (ie. "print debug output"),
but I didn't follow up on it in Kconfig - if you need it to debug CAR,
enable it yourself.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5898 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5896 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
copy&paste, without actually being used.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5894 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Both chipsets use the src/northbridge/intel/i945 code but that code
needs to know which chipset is actually used. Having separate
NORTHBRIDGE_ options allows the I945GC/I945GM choice to be removed
since code can test the NORTHBRIDGE_ option directly.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5893 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5891 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
at the same time let the user specify sources instead
of object files:
- objs becomes ramstage-srcs
- initobjs becomes romstage-srcs
- driver becomes driver-srcs
- smmobj becomes smm-srcs
The user servicable parts are named accordingly:
ramstage-y, romstage-y, driver-y, smm-y
Also, the object file names are properly renamed now, using
.ramstage.o, .romstage.o, .driver.o, .smm.o suffixes consistently.
Remove stubbed out via/epia-m700 dsdt/ssdt files - they didn't
easily fit in the build system and aren't useful anyway.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coreystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5886 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
For the a number of the socket 940 based machines, I collapsed their CAR
configurations into the socket config.
However, I have kept a number of overrides in place for the following
machines:
* broadcom/blast
* ibm/e32{5,6}
* newisys/khepri
* sunw/ultra40
* tyan/s488{0,2}
These machines used different setting than the defaults for socket 940
systems.
Signed-off-by: Warren Turkal <wt@penguintechs.org>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5883 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This change is somewhat dangerous as it enables CAR for some boards that
it was not enabled for before.
Signed-off-by: Warren Turkal <wt@penguintechs.org>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5882 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
configs. I just moved it the the CPU that they all use.
Signed-off-by: Warren Turkal <wt@penguintechs.org>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5871 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
mainboard that uses it.
Signed-off-by: Warren Turkal <wt@penguintechs.org>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5868 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Now we only need to clean out the FAM10 stack mess and we're good to go with a
uniform RAMBASE.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5864 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
USB port for use as Debug Port (on chipsets which support that).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5860 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
that component rather than the mainboard.
The intel/d810e2cb is the only board using the i82801bx southbridge.
Signed-off-by: Warren Turkal <wt@penguintechs.org>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5856 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Most of the mainboards with i82801gx SBs seem to use the
HAVE_HARD_RESET, which is already selected in the i82801gx SB config.
Removing it from some of those boards should be a functional no-op.
Signed-off-by: Warren Turkal <wt@penguintechs.org>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5855 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
All Intel CPU models appear to be identified with the form
INTEL_CPU_MODEL_xxxxx. I haved changed the Atom to fit this normal form.
A side effect is that the CPU doesn't need to be listed on the boards
that support it since the socket identifies the CPUs it supports.
Signed-off-by: Warren Turkal <wt@penguintechs.org>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5853 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Build-tested using abuild.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5844 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Some boards still used the old DEBUG_RAM_SETUP (without _CONFIG prefix).
Also, consistently use "#if CONFIG_DEBUG_RAM_SETUP" (not #ifdef) as we do
elsewhere.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5843 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Drop unused DBGP_DEFAULT #defines on boards with chipsets where no
USB Debug Port support is implemented anyway (at the moment, at least):
- hp/dl145_g3
- hp/dl165_g6_fam10
- ICH7: Move unrelated code out of set_debug_port(). All ICH southbridges
with Debug Port hardcode the physical USB port used as Debug Port to 1.
In other words, this port is not user-configurable (as seems to be
the case on NVIDIA MCP55). For now we keep the 'port' parameter in order
to not change the API, this might be fixed differently later.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5842 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
statement to those files that actually need it. This significantly
reduces the number of dependencies, so it's no longer extremely ugly to
specify them manually (see the src/pc80/Makefile.inc portion)
- Add double include guards around option_table.h defines
- Also, drop the AMD DBM690T work around for the issue
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5838 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
the device tree, instead of using hardcoded values.
If this changes behaviour, this is either
- a bug in mptable_write_buses(), or
- a bug in the old mptable or device config, that is
they were inconsistent.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5835 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5834 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Without a (currently) dummy set_debug_port() function the build fails,
this may or may not be fixed differently in the future.
Manually build-tested on all SB600/SB700 boards, and tested on hardware on
one SB600 board I own, works fine.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5833 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
another recent change into account.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5832 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Original patch was
Signed-off-by: Arne Georg Gleditsch <arne.gleditsch@numascale.com>
Updates to accomodate changes in coreboot are
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5831 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
consits of weak function which always exists (with defaults) and a possibility to
override this with normal function in main.c. This is the other way of
doing that and not using the devictree.cb.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5825 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
On this board all reads from SPD return 0xff by default, there's a custom
GPIO fiddling needed to enable access to the SPD SMBus offsets at
0x50-0x53. While coreboot actually sort of booted sometimes before r5193,
that was just sheer luck as the RAM init was hardcoded in certain ways.
Since the proper, more heavily SPD-based RAM init the brokenness of the
ASUS P3B-F RAM init was becoming visible.
This patch uses GPIOs to enable access to the SPD SMBus offsets,
and resets the GPIOs again after RAM init (this is needed to allow for
lm-sensors to work, for example).
Tested successfully on hardware.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Idwer Vollering <vidwer@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5819 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Marc Jones <marcj303@gmail.com>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5813 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
svn copy amd/mahogany iei/kino-780am2-fam10; then apply the patch.
Signed-off-by: Marc Jones <marcj303@gmail.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5812 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CS5536, ITE IT8712F). Board support is based on the SpaceRunner-LX
(with tiny bits from the RoadRunner-LX) even though the hardware really
was the ancestor of our three other -LX boards and in fact among the
earliest Geode-LX boards on the market. (Might even have been the first
Geode-LX EPIC?)
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTEmbedded.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5801 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
fixes a few alignment wrinkles and sets up and registers the MMCONF area
for AMD Fam10h CPUs (where selected by mainboard configuration). It
removes a bit of code that proved troublesome in MMCONF setups from
mcp55_early_setup_car.c, as per earlier discussion.
Signed-off-by: Arne Georg Gleditsch <arne.gleditsch@numascale.com>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5796 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Geode-LX, CS5536, ITE IT8712F), based on very similar SpaceRunner-LX.
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTEmbedded.de>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5782 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
and SB600.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5781 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
coreboot_ram can be unpacked to 1MB. The value is quickly
replaced with the real value later, thus causing no harm.
Move RAMBASE to the default of 1MB for the affected boards
Signed-off-by: Aurelien Guillaume <aurelien@iwi.me>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5779 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
0xc0000-0xfffff, have coreboot qemu support enable the memory range at
startup.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Acked-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5778 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
standard BIOSes RRLX0013 and SRLX0013. Specifically move SPI and PME
I/Os to 0x1228 and 0x298 and switch SIO watchdog to ext. 48 MHz CLKIN.
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTEmbedded.de>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5775 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
to those files that actually need it. This significantly reduces the number of
dependencies, so it's no longer extremely ugly to specify them manually (see
the src/pc80/Makefile.inc portion)
Also, drop the AMD DBM690T work around for the issue.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5762 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
would rather not have mainboard settings like sio_gp1x_config in the
device tree anyway. So found a nice united home for both in Kconfig,
where users can change them without having to mess around in the C code.
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTEmbedded.de>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5760 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This should be unproblematic, as there are other boards with the same "socket"
that work with CAR already. Tests are highly appreciated though!
Acked-by: Stefan Reinauer <stepan@coresystems.de>
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5755 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Kconfigs from within the choice/endchoice block. This makes it possible to
define user visible board specific options. Moved all vendor names and PCI
ids to the vendors' Kconfigs. Now all options in each file depend on the same
symbol, so replaced all "depends on"s with a single "if". Sorted boards
(sort -d), cleaned whitespace.
This patch also introduces a dummy option BOARD_SPECIFIC_OPTIONS, which is
always "y" and never used. It it simply needed to have something to attach
the boards' "select" statements to.
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTEmbedded.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5754 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- HAVE_HIGH_TABLES
- HAVE_LOW_TABLES
- FALLBACK_SIZE
Jens Rottmann sent an almost identical patch at the same time, so
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTEmbedded.de>
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5745 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
chipset support it. But this involves a long list of 'depends', which you have
to remember updating manually. Converted this into HAVE_... properties, which
will be inherited automatically if someone copies a chipset to create a new
one.
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTEmbedded.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5743 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- prevent GCC from inlining do_ram_command - it will break RAM initialization.
- fix the PCIRST# mechanism in those boards that do it, it requires 200ms, not
200us
- move PCIRST# as early as possible (before ich7_enable_lpc)
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5740 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
* DRAM initialization done message is now printed in debug-mode only, rather than everytime.
Signed-off-by: Aurelien Guillaume <aurelien@iwi.me>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5739 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
I removed the gpio asserts - I think those are not used here.
The pcie 1x slot works, the x1 card I have does not work in 16x slot, but in orig bios I cannot see it any slot, so it is kind of better.
The classic PCI slot works fine too. However it seems SATA has some issues.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5720 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
http://www.gigabyte.cn/products/product-page.aspx?pid=3118#ov
the simple config is
AM2+DDR2+SB700+RS780, the superIO is IT8718F
The patch has been tested with SeaBIOS + SUSE11.2
Signed-off-by: Wang Qing Pei <wangqingpei@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5715 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
