Some of the Lynx Point ids were off. Correct those and make
the pei data BAR fields consistent with the others.
Change-Id: I4102439588362cdb94643bd1ce69c9fa4278329e
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2622
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The CS5536 companion device has three different power domains.
* working domain
* standby domain
* RTC domain
When the system is "off" only the standby domain is powered.
MFGPT[7:6] are member of the standby power domain.
MFGPT7 is used to control the backlight of the device and so the
timer gets used and configured during system boot. If the system
does a reboot the timer stays configured and the Linux driver
can not use it:
"ot200-backlight: ot200-backlight.0: MFGPT 7 not availale"
The cs5535-mfgpt has a function to hard-reset all MFGPTs but the
system hangs after the first access to a MFGPT register - cause
unknown.
/*
* This is a sledgehammer that resets all MFGPT timers. This is required by
* some broken BIOSes which leave the system in an unstable state
* (TinyBIOS 0.98, for example; fixed in 0.99). It's uncertain as to
* whether or not this secret MSR can be used to release individual timers.
* Jordan tells me that he and Mitch once played w/ it, but it's unclear
* what the results of that were (and they experienced some instability).
*/
static void reset_all_timers(void)
{
uint32_t val, dummy;
/* The following undocumented bit resets the MFGPT timers */
val = 0xFF; dummy = 0;
wrmsr(MSR_MFGPT_SETUP, val, dummy);
}
After playing around with this undocumented MSR it looks like I only
need to set bit 7 to free the MFGPT7.
BTW, all MFGPT[0:5] will be reset during pll_reset().
Change-Id: I54a8d479ce495b0fc2f54db766a8d793bbb5d704
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-on: http://review.coreboot.org/2527
Tested-by: build bot (Jenkins)
Reviewed-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
This is no longer tied to a GPIO but has a proper chipset pin.
Change-Id: Iba70338e8c67e3c3c1cb32e69bfea1282fda8cb5
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2643
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Now that MMCONF_SUPPORT_DEFAULT is enabled by default remove
the pcie explicit accesses. The default config accesses use
MMIO.
Change-Id: I8406cec16c1ee1bc205b657a0c90beb2252df061
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2618
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The register that controls global reset is named the Power
Mangement Initialization Regiser (PMIR). Update the defines
to reflect the documentation.
Additionally, there is no core well reset control according to the
EDS. There is, however, a CF9 lock field to lock this register down.
Change-Id: I773c33bec63a06cdb869eb9f94553d476e492798
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2619
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The ME9 requirements have added some registers and changed some
of the MBP state machine. Implement the changes found so far in
the ME9 BWG. There were a couple of reigster renames, but the
majority of th churn in the me.h header file is just introducing
the data structures in the same order as the ME9 BWG.
Change-Id: I51b0bb6620eff4979674ea99992ddab65a8abc18
Signed-Off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2620
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The IA32_ENERGY_PERFORMANCE_BIAS MSR can only be read or written
to if the CPU supports it. The support is indicated by ECX[3] for
cpuid(6). Without this guard, some Haswell parts would GP# fault
in this routine.
No more GP# while running on haswell CRBs.
Change-Id: If41e1e133e5faebb3ed578cba60743ce7e1c196f
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2639
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
In order for coreboot to assign resources properly the pci
drivers need to have th proper device ids. Add the host controller
and the LPC device ids for Lynx Point.
Resource assignment works correctly now w/o odd behavior because
of conflicts.
Change-Id: Id33b3676616fb0c428d84e5fe5c6b8a7cc5fbb62
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2638
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
The reference code sends the dram init done command to the ME.
Therefore, there is no need for coreboot to do this.
Change-Id: I6837d6c50bbb7db991f9d21fc9cdba76252c1b7b
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2633
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Even though this is under the graysreef board it really
applies to the Basking Ridge board. A subsequent patch will
rename graysreef to baskingridge.
The GPIO pins were updated to reflect the Basking Ridge schematics
as well as the DIMM spd addresses and USB over current pins.
Change-Id: Ice4e05f5203de3024cd463dfccf0bcfec1e247c1
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2632
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Add a FIXME about checking a MCHBAR register that isn't setup yet.
Also, remove revision updating because I can't find anything in the
docs that suggest this is required for haswell.
Change-Id: Ia8a6e08f82e18789e31c6c2ec2c1d63740c18dc4
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2631
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The intel-framework code has an updated pei_data structure.
Use the new structure and revision. Also, remove the scrambler
seed saving in CMOS since that appears to be handled in the saved
data from the reference code.
Change-Id: Ie09a0a00646ab040e8ceff922048981d055d5cd2
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2630
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Change the hard coded values in udelay.c to use the #defines
for MSRs and BCLK.
Change-Id: I2bbeb0b478d2e3ca155e8f82006df86c29a4f018
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2629
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Grays Reef is one of Intel's CRBs for the Haswell processor. The
platform is named Shark Bay.
GPIOs were the main focus so IRQ routing and ACPI still needs to be
further looked at.
Change-Id: Ie94b7af66f772714992a92612c76ca93b9b27088
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2621
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This is the steps outlined in the BWG.
It seems this is a lot simpler now (so far) which is good.
To test, boot to chromeos with 3.7 kernel + i915.preliminary_hw_support=1 and
see that the i915 driver complains a lot less than before and that a
splashscreen is displayed.
Change-Id: I722c90ecd351860949cedab24533f6c10e5b90e5
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2696
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This follows the new method outlined in the LPT BWG.
It is also very pedantic about its operation so it
is easier to read and compare against the docs and
the reference code implementation.
Change-Id: I235d634cded0c75ec0e9f53488f5b366107a18fa
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/2694
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Add support for SMM modules by leveraging the RMODULE lib. This allows
for easier dynamic SMM handler placement. The SMM module support
consists of a common stub which puts the executing CPU into protected
mode and calls into a pre-defined handler. This stub can then be used
for SMM relocation as well as the real SMM handler. For the relocation
one can call back into coreboot ramstage code to perform relocation in
C code.
The handler is essentially a copy of smihandler.c, but it drops the TSEG
differences. It also doesn't rely on the SMM revision as the cpu code
should know what processor it is supported.
Ideally the CONFIG_SMM_TSEG option could be removed once the existing
users of that option transitioned away from tseg_relocate() and
smi_get_tseg_base().
The generic SMI callbacks are now not marked as weak in the
declaration so that there aren't unlinked references. The handler
has default implementations of the generic SMI callbacks which are
marked as weak. If an external compilation module has a strong symbol
the linker will use that instead of the link one.
Additionally, the parameters to the generic callbacks are dropped as
they don't seem to be used directly. The SMM runtime can provide the
necessary support if needed.
Change-Id: I1e2fed71a40b2eb03197697d29e9c4b246e3b25e
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2693
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Add a bootblock.c file for the northbridge and setup the
PCIEXBAR as the first thing using IO PCI config acceses.
After that all PCI config accesses can use MMIO.
Change-Id: I51d229c626c45705dda1757c2f14265cbc0e6183
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2617
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The Haswell parts use a PCH code named Lynx Point (Series 8). Therefore,
the southbridge support is included as well. The basis for this code is
the Sandybridge code. Management Engine, IRQ routing, and ACPI still requires
more attention, but this is a good starting point.
This code partially gets up through the romstage just before training
memory on a Haswell reference board.
Change-Id: If572d6c21ca051b486b82a924ca0ffe05c4d0ad4
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2616
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The original code attempted to reserve a space in RAM for coreboot to
remain resident. This turns out not to be needed, and breaks things
for the kernel since the exynos5250-smdk5250 kernel device tree starts
RAM at 0x40000000.
(This patch was originally by Gabe, I'm just uploading it)
Change-Id: I4536edaf8785d81a3ea008216a2d57549ce5edfb
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2698
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
Change the OSC method to actually grant control of
PCIe capabilities to the OS instead of granting no
control. I believe the logic was backwards in the
original commit. Bits should be set when granting
control and cleared when not granting control. By
setting the return value to 0x00, we effectively
tell the OS that it cannot control any PCIe
capability. See section 6.2.9 of the ACPI spec
version 3.0 for more information.
This edit is a duplication of the OSC method that
is in the src/southbridge/intel/bd82x6x/pch.asl
file.
Change-Id: Id2462ab12203afceb9033f24d06b4dfbf2236d2e
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2714
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This enables branch prediction. We can probably find a better place
to do this, but for now we'll do it in snow's romstage main().
Change-Id: I86c7b6bc9e897a7a432c490fb96a126e81b8ce72
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2701
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Since commit »Drop redundant CHIP_NAME in mainboard.c« (a93c3fe7) [1]
`CHIP_NAME` is unneeded for mainboards as the name is composed
automatically in `src/devices/root_device.c` from the strings in
Kconfig.
Unfortunately the ports for Google Butterfly, Link and Parrot as
as well as IEI PM-LX2-800-R10 introduced CHIP_NAME again. So drop
it again too.
[1] http://review.coreboot.org/1635
Change-Id: Ice7577a2a5c6070e196f2647c440b7a8e140e27e
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2708
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
PS_HOLD gets set in exynos' power_init().
Change-Id: Ib08e0afcad23cbd07dc7e3727fd958a1bc868b5a
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2700
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Call the power_init() function. We appear to have forgotten about it
when deprecating lowlevel_init_subsystems(), but it didn't seem to
cause problems until we got to doing more interesting stuff recently.
There are some clean-ups to do from the original code, such as not
attempting to configure I2C from PMIC code, which we'll get around
to in follow-up patches.
(Credit to Gabe for spotting this)
Change-Id: I6a59379e9323277d0b61469de9abe6d651ac5bfb
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2699
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The current default is IDE mode which is slower compared to AHCI
mode. Therefore use AHCI mode by default.
A similar change was made for AMD Persimmon in commit
»Enable SATA AHCI for faster boot with SeaBIOS.« (96be74c7) [1]
but was indirectly reverted by »sb800: Add sata ahci/raid mode
kconfig option« (d4a0e7d0) [2].
[1] http://review.coreboot.org/220
[2] http://review.coreboot.org/225
Change-Id: I4fa31b0a3280891e7a3f37675ae8415205818947
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2661
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
There's a compile time error that we didn't catch since the
board defaults as used by the build bot won't expose it.
Just make watchdog_off() a no-op statement so there aren't any
stray semicolons in the preprocessor output.
Change-Id: Ib5595e7e8aa91ca54bc8ca30a39b72875c961464
Reported-by: 'lautriv' on irc.freenode.net/#coreboot
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/2627
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
We used to allow mainboards to override subsystems using
mainboard_pci_subsystem_vendor_id and mainboard_pci_subsystem_device_id.
Mechanisms have changed and the only occurrence of these names is in
the header.
Change-Id: Ic2ab13201a2740c98868fdf580140b7758b62263
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/2625
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Despite everywhere the model name M5A88-V is used, in Kconfig the
string M5A88PM-V is used. Searching for that model string on the
WWW does not return anything which is unrelated to coreboot, so
change that string to M5A88-V.
Change-Id: I25cf9d4a5fc3f9b9356e8616452066ebf873f44c
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2613
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: QingPei Wang <wangqingpei@gmail.com>
Add PEI updates and ACPI updates for supporting EHCI to XHCI
USB port support.
Change-Id: I9ace68a1b3950771aefb96c1319b8899291edd9a
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/2519
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Adding the 'WordBusNumber' macro to the PCI0
CRES ResourceTemplate in the Persimmon DSDT.
This sets up the bus number for the PCI0 device
and the secondary bus number in the CRS method.
This change came in response to a 'dmesg' error
which states:
'[FIRMWARE BUG]: ACPI: no secondary bus range in _CRS'
By adding the 'WordBusNumber' macro, ACPI can set
up a valid range for the PCIe downstream busses,
thereby relieving the Linux kernel from "guessing"
the valid range based off _BBN or assuming [0-0xFF].
The Linux kernel code that checks this bus range is
in `drivers/acpi/pci_root.c`. PCI busses can have
up to 256 secondary busses connected to them via
a PCI-PCI bridge. However, these busses do not
have to be sequentially numbered, so leaving out a
section of the range (eg. allowing [0-0x7F]) will
unnecessarily restrict the downstream busses.
This change will apply to other AMD mainboards and
will be in a different commit.
Change-Id: I44f22bc03a0dcbcd2594d4291508826cc2146860
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2592
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
This eliminates the use of do_div() in favor of using libgcc
functions.
This was tested by building and booting on Google Snow (ARMv7)
and Qemu (x86). printk()s which use division in vtxprintf() look good.
Change-Id: Icad001d84a3c05bfbf77098f3d644816280b4a4d
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2606
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Changes:
- Get rid of the inagua mainboard specific code and use the
platform generic function wrapper that was added in change
http://review.coreboot.org/#/c/2497/
AMD f14: Add SPD read functions to wrapper code
- Move DIMM addresses into devicetree.cb
- Add the ASF init that used to be in the SPD read code into
mainboard_enable()
Notes:
- The DIMM reads only happen in romstage, so the function is not
available in ramstage. Point the read-SPD callback to a generic
function in ramstage.
Change-Id: Id05227fcf18c6ab94ffe1beb50b533ab7b0535db
Signed-off-by: Kimarie Hoot <kimarie.hoot@se-eng.com>
Reviewed-on: http://review.coreboot.org/2607
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Currently for Advansus A785E-I, ASRock E350M1 and ASUS M5A88-V
despite what is chosen in Kconfig »Chipset« menu item,
$ more .config
[…]
# CONFIG_ENABLE_IDE_COMBINED_MODE is not set
CONFIG_IDE_COMBINED_MODE=0x1
# CONFIG_SB800_SATA_IDE is not set
CONFIG_SB800_SATA_AHCI=y
# CONFIG_SB800_SATA_RAID is not set
CONFIG_SB800_SATA_MODE=0x2
[…]
the SATA controller is put into IDE mode.
$ lspci -nn | grep SATA
00:11.0 SATA controller [0106]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 SATA Controller [IDE mode] [1002:4390] (rev 40)
Commit »sb800: Add sata ahci/raid mode kconfig option«
(d4a0e7d0) [1] added the options above to configure the mode
using Kconfig and some SB800 boards were adapted already. For
example commit »persimmon: sb800 sata mode configure update«
(1386fa74) [2] did so for AMD Persimmon.
Doing the same by assigning the Kconfig variable to the value in
`platform_cfg.h` integrates this with the three remaining boards
listed above.
The patch is successfully tested with the ASRock E350M1.
$ lspci -nn | grep SATA
00:11.0 SATA controller [0106]: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 SATA Controller [AHCI mode] [1002:4391] (rev 40)
[1] http://review.coreboot.org/225
[2] http://review.coreboot.org/227
Change-Id: I227257e2c8f04f18c27ff00fe62d42e372de67e4
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2610
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Replace »persimmon« by »board« in comment to keep `diff` output
between boards small.
Change-Id: Ieae2a63782c488ae35f22eb30f5b1049200d12c8
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2611
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Changes:
- Get rid of the union_station mainboard specific code and
use the platform generic function wrapper that was added
in change http://review.coreboot.org/#/c/2497/
AMD f14: Add SPD read functions to wrapper code
- Move DIMM addresses into devicetree.cb
- Add the ASF init that used to be in the SPD read code into
mainboard_enable()
Notes:
- The DIMM reads only happen in romstage, so the function is not
available in ramstage. Point the read-SPD callback to a generic
function in ramstage.
Change-Id: I19d6b0d674b67294519383f80928471b37da1e14
Signed-off-by: Kimarie Hoot <kimarie.hoot@se-eng.com>
Reviewed-on: http://review.coreboot.org/2609
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Changes:
- Get rid of the south_station mainboard specific code and
use the platform generic function wrapper that was added
in change http://review.coreboot.org/#/c/2497/
AMD f14: Add SPD read functions to wrapper code
- Move DIMM addresses into devicetree.cb
- Add the ASF init that used to be in the SPD read code into
mainboard_enable()
Notes:
- The DIMM reads only happen in romstage, so the function is not
available in ramstage. Point the read-SPD callback to a generic
function in ramstage.
Change-Id: If4291d25ea81bf375f55b64c07c223a847a211d0
Signed-off-by: Kimarie Hoot <kimarie.hoot@se-eng.com>
Reviewed-on: http://review.coreboot.org/2608
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This is previously used exception code from libpayload.
On startup it installs and then tests an exception handler.
The test is an unaligned memory operation.
Yes, we've seen what might be exceptions in the ramstage, and
it makes sense to handle them. This code is identical in structure
and operation to the previously committed payload exception handler,
though we reserve the right to change it as circumstances require.
The remaining question is whether we need it in romstage.
Change-Id: I24484686c33c9757af8ba171ebae9773828fb69d
Signed-off-by: Gabe Black <gabeblack@google.com>
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2614
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
AGESA code has wrong definition of CR0_PE bit (1 instead of 0).
PE [Protected Mode Enable] is 0 bit in CR0 register
(If PE=1, system is in protected mode, else system is in real mode)
Bit 1 is MP [Monitor co-processor]
(Controls interaction of WAIT/FWAIT instructions with TS flag in CR0)
System uses CR0_PE define, but I didn't expect any consequences because of this bug.
Change-Id: I54d9a8c0ee3af0a2e0267777036f227a9e05f3e1
Signed-off-by: Konstantin Aladyshev <aladyshev@nicevt.ru>
Reviewed-on: http://review.coreboot.org/2591
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
According to BKDG:
"Memory controller (MCT) and DRAM controllers (DCTs) additions:
• Support for 933 MHz (1866 MT/s) MEMCLK frequency."
Change-Id: I6f307ce3fcb355d5445f1ea86def73a41b928a57
Signed-off-by: Konstantin Aladyshev <aladyshev@nicevt.ru>
Reviewed-on: http://review.coreboot.org/2589
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
_RDMSR instruction loads the contents of a 64-bit model specific register (MSR)
specified in the ECX register into registers EDX:EAX.
The EDX register is loaded with the high-order 32 bits of the MSR
and the EAX register is loaded with the low-order 32 bits.
EDX:EAX = MSR[ECX]
So bit 49 will be contained in EDX register.
Buggy code instead of bit 49 (CombineCr0Cd) sets bit [49-32=17] (PfcStrideDis).
PfcStrideDis bit disables stride prefetch generation. This leads to memory
bandwidth loss.
_________
Supermicro H8QGI board
After applying this change i observed huge memory bandwidth increase in tests
that runs on small amount of cores. But unfortunately it doesn't affect
overall bandwidth results on 4P system with 48 cores.
So i think that in this system leading limiting factor is
AMD HT-ASSIST feature (Probe filter).
But right now it is not working. System stucks in Linux boot. I have done
some experiments and figured out that stuck happens when system have cores in
compute unit (CU) other than CU with BSC (boot strap core).
CU is two cores (primary and seconary) that shares some things (L2 cache, FPU ...)
So with probe filter i can boot Linux with one (BSC)
or two (BSC + secondary core in its CU) cores.
And with this configuration i can see memory bandwidth on 1 core (or two cores)
close to original bios.
Change-Id: I5a95f5b753d600c70d3c93d36fecc687610c61cd
Signed-off-by: Konstantin Aladyshev <aladyshev@nicevt.ru>
Reviewed-on: http://review.coreboot.org/2588
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
The Hudson-E1's default SPI speed for normal i.e. non-fast reads is 66 MHz,
but the SST 25VF032B datasheet allows max. 25. Lower the speed to 22 MHz,
otherwise BIOS flashing fails.
Change-Id: I22e87d833a3ebd316b6e873595a2480831533ab1
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-on: http://review.coreboot.org/2605
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Changes:
- Get rid of the persimmon mainboard specific code which has been
moved into the wrapper as a platform generic function in change
http://review.coreboot.org/#/c/2497/
AMD f14: Add SPD read functions to wrapper code
- Move DIMM addresses into devicetree.cb
- Add the ASF init that used to be in the SPD read code into
mainboard_enable()
Notes:
- The DIMM reads only happen in romstage, so the function is not
available in ramstage. Point the read-SPD callback to a generic
function in ramstage.
Change-Id: I5f017dbb8dee5a09ec19734a6069ff9b71a6ab50
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2500
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Change:
This is the initial step for moving the AMD F14 & HUDSON1,2,3
SPD-read callout out of the mainboard directories and into
the wrapper. The next step is to update the platforms to use
this routine in BiosCallouts.c and to delete the code from the
mainboard directories. The DIMM addresses should be moved into
devicetree.cb.
If there are significant differences or reasons that the mainboard
needs to override this code, it's perfectly reasonable to keep using
the version in the mainboard, but this allows us to remove duplicated
code and simplify the mainboard directories.
Notes:
This started by duplicating what was in Persimmon, and was changed to
use the devicetree.cb structures. The ASF setup was also removed from
the persimmon copy (PMIO writes to 0x28 & 0x29) as that's not needed
for the SPD access and doesn't make sense to initialize here.
Significant cleanup and magic number reduction was done as well.
It is intended that this file will not be included in ramstage as
the DIMM init is all done in romstage.
This is similar to what was done for Parmer/Thatcher in commit
7fb692bd - http://review.coreboot.org/#/c/2190/
Fam15tn: Move SPD read from mainboards into wrapper
Yes, it would make sense to split this into two separate files
and move the SMBUS initialization and access into the southbridge
wrapper. Maybe that can come next.
Change-Id: I1e106d3912c160b0015bf02158d9faba4f578ee3
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2497
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
I've used an operating system for over 10 years now that makes
UTF-8 easy. It's not called Linux or OSX.
When UTF-8 is needed, of course, then we can look again.
I can't think of a single redeeming feature of placing
it in the comment in this manner. It's certainy not
needed.
The inclusion of UTF-8 characters is inconvenient,
especially from a text terminal.
I don't really want to start using compose in
CROSH shell terminals on chromeos.
We might want to incorporate "no UTF-8" as a
commit filter. For now, get rid of these
characters.
Change-Id: If94cc657bae1dbd282bec8de6c5309b1f8da5659
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2604
Reviewed-by: Bernhard Urban <lewurm@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This reverts commit 1cd6160821
Division bites us again. I don't know how or why, but printk() seems to break (again) with this patch. I'm surprised we didn't encounter problems earlier on...
Change-Id: I81cb9f20879f5eb73a76e1af47b96a68d1e81dc8
TODO: Find a better solution for div64. This one is too painful, but seems necessary for now (and sort-of works with our vtxprintf hack).
Reviewed-on: http://review.coreboot.org/2600
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This adds some real GPIO mappings where virtual GPIOs were used before.
Change-Id: I25d4be45f986c8d622b97151f8bdae2651baf3e6
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2603
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This adds an enum for GPIO ports on the Exynos5. To make them
useful, they are assigned the absolute MMIO address where a
s5p_gpio_bank struct can point to.
Change-Id: Ia539ba52d7393501d434ba8fecde01da37b0d8aa
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2602
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
While reading through the file fix some spotted errors like
indentation, locution(?), capitalization and missing full stops.
Change-Id: Id435b4750e329b06a9b36c1df2c39d2038a09b18
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2484
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
A board without HAVE_ACPI_RESUME did not build with
COLLECT_TIMESTAMPS enabled as `cbmem.c` was not built.
Change-Id: I9c8b575d445ac566a2ec533d73080bcccc3dfbca
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/2549
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Quoting Jens Rottmann [1]:
Nevertheless I still think this whole function is bogus for the E350M1. The
function assumes GPIO21 is wired to reset APU PCIe lane 0+1 (PCIe x8, port 4+5
as Coreboot/AGESA calls it), GPIO25 resets lane 2 (PCIe x4) and GPIO02 lane 3.
But the E350M1 has PCIe x16 i.e. probably APU lanes 0-3 bundled, completely
different layout. They could have chosen GPIO21 to force resets, or 25 - or
maybe 50 like on the Persimmon or any other they fancied or - and this is the
most probable - none at all. Having BiosGnbPcieSlotReset() toggle some GPIOs
without knowing what they do on the E350M1 (if anything at all) is nonsense.
In my opinion this whole function should just "return AGESA_UNSUPPORTED" and
good riddance.
[1] http://review.coreboot.org/#/c/2445/
Change-Id: Iac66da41182e838c7e6925250cc3982adbb3e4ec
Reported-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2489
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
These are essential functions for setting up the display port and
framebuffer, and also enable such things as aux channel
communications. We do some very simple initialization in romstage,
mainly set a GPIO so that the graphics is powering up, but the complex
parts are done in the ramstage. This mirrors the way in which graphics
is done in the x86 size.
I've added a first pass at a real device, and put it in the mainboard
Kconfig, hoping for corrections. Because startup is so complex,
depending on device type, I've created a 'displayport' device that
removes some of the complexity and makes the flow *much* clearer. You
can actually follow the flow by looking at the code, which is not true
on other implementations. Since display port is perhaps the main port
used on these chips, that's a reasonable compromise. All parameters of
importance are now in the device tree.
Change-Id: I56400ec9016ecb8716ec5a5dae41fdfbfff4817a
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2570
Tested-by: build bot (Jenkins)
Since the merg of the ASRock E350M1 port (a649a96e) the compiler
warns about the following [1].
mainboard.c:35, GNU Compiler 4 (gcc), Priorität: Normal
no previous prototype for 'set_pcie_reset' [-Wmissing-prototypes]
mainboard.c:43, GNU Compiler 4 (gcc), Priorität: Normal
no previous prototype for 'set_pcie_dereset' [-Wmissing-prototypes]
Adding the function prototypes to the beginning of the file as
done in commit »Persimmon updates for AMD F14 rev C0« (d7a696d0)
addresses the warning.
[1] http://qa.coreboot.org/job/coreboot-gerrit/4975/warnings13Result/package.-139448264/file.-1544928473/
[2] http://review.coreboot.org/137
Change-Id: Iad2e62ec37c3a2f749a264974b61ac7c226e9b83
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2590
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Set up the clocks used for sound and turn on the sound clock.
Change-Id: Ic59bfa9ae87116299503e6d25aeefba98c842fb8
Signed-off-by: Gabe Black <gabeblack@google.com>
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2587
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
The MMC0 on google/snow can run in 8 bit mode. To simplify driver development,
we thought disabling it (using zero, which runs in 1-bit / 4-bit mode) may help.
However, after some experiments in payload drivers, setting pinmux to 8 bit mode
can still allow MMC to run in 1-bit / 4-bit mode, so it's pretty safe to enable
8 bit mode by default for better performance.
Verified to boot on google/snow, and got MMC0 working.
Change-Id: Ic0acc723fe6a8aecf373429d3801beadd70815d9
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2585
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
The power up default for the 14M_25M_48M_OSC switchable clock output ball of
the SB800 chipset is 14 MHz. sb800/bootblock.c changes this to 48 MHz,
which is the correct value for almost all SIOs. However, not for
'smscsuperio' (SMSC SCH311x), which needs the original 14 MHz and is not
configurable for other clock speeds. A wrong SIO clock supply results in
funny RS232 output (wrong bit speed) and non-working PS/2.
We could switch back to 14 MHz in the mainboard's romstage.c, but then the
clock frequency would change twice. The resulting short 48 MHz burst causes
a handful of rubbish characters on RS232 on every boot until the SIO clock
has stabilized again.
This patch skips the SB800 clock switch if the SIO Kconfig requests 14 MHz.
This does not affect any boards currently in the repository (yet).
Change-Id: Icff41fd88dc41c08f3700ab4f786852f04eff2a4
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-on: http://review.coreboot.org/2454
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
The first reason for selecting the CPU model at compile time was a
multi-second pause if booting a single core Fusion T40R with MAX_CPUS=2.
Recent tests show the pause has disappeared, someone must have fixed it.
The second reason was me not knowing how to make a single vgabios image
work with two different PCI IDs. Many thanks to Martin Roth for educating
me! Quote:
"The way to make coreboot use the same vbios for different video device IDs
is through the map_oprom_vendev function. In family 14 it's in
northbridge/amd/agesa/family14/amdfam14_conf.c You would name your video
bios 1002,9802 in the config and all the other device/vendor IDs for the
family 14h processors will fall through the initial check for the video
bios and will get remapped to use that vbios. This only works if you're
initializing the vbios inside coreboot. I don't know if you're using
SeaBios as a payload, but if you are you can add the vbios to cbfs as
vgaroms/vbios.rom and the rom will always be initialized."
I'd like to add the vgabios is added as type 'optionrom' when Coreboot make
adds it, however to work with SeaBios it has to be added manually with
cbfstool and with type 'raw', or it will hang.
Change-Id: I8190d0c3202a60dfccb77dde232f9ba7ce5ce318
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-on: http://review.coreboot.org/2584
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
OK, this is tl;dr. But I need to write this in hopes we make
sure we don't put code like this into coreboot. Ever.
Our excuse in this case is that it was imported, not obviously wrong,
and easily changed. It made sense to get it in, make it work, then
do a cleanup pass, because changing everything up front is almost
impossible to debug.
The exynos code has bunch of base register values, e.g.
These are base addresses of things that look like a memory-mapped
struct. To get these to a pointer, they created the following macro,
which creates an inline function.
static inline unsigned int samsung_get_base_##device(void) \
{ \
return cpu_is_exynos5() ? EXYNOS5_##base : 0; \
}
And then invoke it 31 times in a .h file, e.g.:
SAMSUNG_BASE(clock, CLOCK_BASE)
to create 31 functions.
And then use it:
struct exynos5_clock *clk =
(struct exynos5_clock *)samsung_get_base_clock();
OK, what's wrong with this? It's easier to ask what's right with it. Answer: nothing.
I have a long list of what's wrong, and I may leave some things out,
but here goes:
1. the "function" can return a NULL if we're not on exynos5. Most uses of the code
don't check the return value.
2. And why would this function be running, if we're not on an exynos5? Why compile it in?
3. Note the cast everywhere a samsung_get_base_xxx is used.
The function returns an untyped variable, requiring the *user* to get two
things right: the cast, and the function invocation. One can replace that _clock(); with
_power(); in the code above, and they will be referencing the wrong registers, and
they'll never get an error!
We have a C compiler; use it to type data.
4. You're generating 31 functions using cpp each and every time the file is included.
The C compiler has to parse these each time. It's not at all like a simple cpp
macro which is only generated on use.
5. You can't tags or etags this code
6. In fact, any kind of analysis tool will be unable to do anything with this cpp magic.
That's only a partial list.
So what's the right way to do it? Just make typed constants, viz:
Or, since I expect people will want the lower case function syntax, I've left
it that way:
Now we've got something that is efficient, and we don't even need to protect with
any more.
Hence this change. We've got something that is type checked, does not require users to
cast on each use, will catch simple programming errors, can be analyzed with standard tools,
and builds faster.
So if we make a mistake:
struct exynos5_clock *clk =
samsung_get_base_adc();
We'll see it:
src/cpu/samsung/exynos5250/clock.c: In function 'get_pll_clk':
src/cpu/samsung/exynos5250/clock.c:183:3: error: initialization from incompatible pointer type [-Werror]
which we would not have seen before.
As a minor benefit, it shaves most of a second off the compilation.
Change-Id: Ie67bc4bc038a8dd1837b977d07332d7d7fd6be1f
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2582
Tested-by: build bot (Jenkins)
Update coreboot to use SeaBIOS' tag rel-1.7.2.1
Change-Id: I01969407964a7cf64f7c4800b59c6aed845b24f9
Signed-off-by: Idwer Vollering <vidwer@gmail.com>
Reviewed-on: http://review.coreboot.org/2575
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Commit f154c018
Author: Marc Jones <marcj303@gmail.com>
Date: Wed Dec 14 11:24:00 2011 -0700
Persimmon audio codec verb patch.
Reviewed-on: http://review.coreboot.org/490
has a typo code*c* in the comments for `AZALIA_OEM_VERB_TABLE`. As
this was copied over to the LiPPERT Fam14 boards, use the following
command to fix the typo.
$ git grep -l cocec | xargs sed -i s,cocec,codec,
Change-Id: I1525b0445edab81ab136b3adece52b78ba7abc71
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2576
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
If you try to reset the system with outb(3,0x92), outb(4,0xcf9) or a
triple-fault it will instead crash with a messy screen. As the more common
outb(0xFE, 0x64) doesn't work with our setup, Linux will crash whenever you
ask it to reboot. Closer inspection shows that on a warm boot of Coreboot
agesawrapper_amdinitpost() always fails with error code 7. Looks like DDR3
re-init goes wrong somehow. I tried find the reason for this but was
unable to. I am convinced this is not board specific but a bug in AGESA.
In the end I had to settle for a workaround: if amdinitpost returns 7 this
patch resets the system harder with outb(0x06, 0x0cf9), after that RAM init
will succeed. As amdinitpost is early in POST this automatic reset is
quick enough not to be noticable.
I'd perfer a real fix, but that's all I have.
Change-Id: I4763254b489f42a135232e45328ecf0d5c4d961a
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-on: http://review.coreboot.org/2573
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Step 2: change the Persimmon code to adapt it to the new board's hardware.
The Toucan-AF is a COM Express Compact Type 6 form factor embedded board:
- AMD Fusion G-T56N (1.65 GHz dual core) or T40R (1 GHz single core) APU
- 1-4 GB DDR3 memory down
- 1x VGA, 2x DisplayPort (1 switchable to LVDS)
- AMD A55E (Hudson-E1) southbridge
- 8x USB 2.0
- 4x SATA
- HD Audio (with codec on baseboard)
- NEC uPD78F0532 microcontroller on I2C ("SEMA")
- 7x PCIe2.0 x1 (1 on PEG)
- Intel I210 GbE (on APU PCIe x1, can be disabled for additional PCIe)
- 2x SST 25VF032B (SO8, soldered) 4 MB SPI flash (BIOS and failsafe BIOS)
The Toucan-AF has no SIO on board. This patch includes basic support for a
Winbond W83627DHG (PS/2, 2x RS232), because the ADLINK ExpressBase-6 used
for evaluation happens to have one. The code may have to be adapted to the
actual baseboard of the application.
http://www.adlinktech.com/PD/web/PD_detail.php?pid=1132
Change-Id: I9041b905bad45852ac9b402fcbd5decbc98b377b
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-on: http://review.coreboot.org/2572
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Step 1: copy all files unmodified from Persimmon. This makes it much
easier later to see how the two boards actually and deliberately differ
when porting bugfixes from one to the other. Git's copy detection is
imperfect (and slow).
Change-Id: I1ff02913479c07679f8c3ae5e6dd7876e6000b55
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-on: http://review.coreboot.org/2571
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Step 1: copy all files unmodified from Persimmon. This makes it much
easier later to see how the two boards actually and deliberately differ
when porting bugfixes from one to the other. Git's copy detection is
imperfect (and slow).
Change-Id: I2fd1bf8428fc8a1e7becee888b6182b9bd8166a0
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-on: http://review.coreboot.org/2552
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
In the file `COPYING` in the coreboot repository and upstream [1]
just one space is used.
The following command was used to convert all files.
$ git grep -l 'MA 02' | xargs sed -i 's/MA 02/MA 02/'
[1] http://www.gnu.org/licenses/gpl-2.0.txt
Change-Id: Ic956dab2820a9e2ccb7841cab66966ba168f305f
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2490
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
The SD/MMC interface on Exynos 5250 must be first configured with, GPIO, and
pinmux settings before it can be detected and used in ramstage / payload.
Verified on armv7/snow and successfully boot into ramstage.
Change-Id: I26669eaaa212ab51ca72e8b7712970639a24e5c5
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2561
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This breaks booting, and in fact stages.c is always going to be special: for it to work it has to be compiled for arm only, no thumb allowed. It's probably better to leave the stages.o target in explicitly so it's clear that it has to be compiled with a particular set of flags, rather than try to remember that we must always have the default rules no break stages.c compilation. That would be a mess. I will be pushing a CL to get rid of the assembly dump, but will be a trivial fix.
This reverts commit 8f4647a24b
Change-Id: I5e3d8e5b991f6ccf4d49078378cd4615fb230ca0
Reviewed-on: http://review.coreboot.org/2554
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This allows to drop some special cases in romstage.c
Change-Id: I53fdfcd1bb6ec21a5280afa07a40e3f0cba11c5d
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2551
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
It's not used, and not needed.
Change-Id: Ifca92f3606ac58fc26e09676488c3add5d84ae79
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2548
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This is a leftover from when we were debugging
this code. Let's make it easier to understand.
Change-Id: Ia3d0ab1504ff9dd9634d5f393d3c59fe1e43a0c0
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2543
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
It's been on for all boards per default since several years now
and the old code path probably doesn't even work anymore. Let's
just have one consistent way of doing things.
Change-Id: I58da7fe9b89a648d9a7165d37e0e35c88c06ac7e
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2547
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The ARM CPUs we know of don't have CPU microcode updates,
so don't show the selection in Kconfig.
Also simplify (and fix) the microcode selection in the Makefile
that would try to include microcode even though none is available.
Change-Id: I502d9b48d4449c1a759b5e90478ad37eef866406
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2540
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
Add two more GPIOs (total 6) as needed by the Google Snow laptop.
These are faking out settings for now. This code is tested and working.
Change-Id: I2077ffb8b85958eefdf54e19763d57cc1178ce89
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2538
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: build bot (Jenkins)
Commit 8487229b (Persimmon doesn't have HDMI so the GNB HD Audio should be
disabled.) turned off the device in AGESA. Now remove it from
devicetree.cb, too. This prevents the following boot message:
PCI: Left over static devices:
PCI: 00:01.1
PCI: Check your devicetree.cb.
Also clarify the line's comment a bit for the Fam14 boards which still
retain this device (to counter the loss of information ;-).
Change-Id: Ib671ed2e0d04bdef2869e8d70208d6e55cdea3fd
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-on: http://review.coreboot.org/2537
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
Entry point in payload segment header is a 64 bit integer (ntohll). The debug
message is currently reading that as a 32 bit integer (which will produce
00000000 for most platforms).
Change-Id: I931072bbb82c099ce7fae04f15c8a35afa02e510
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2535
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
According to both Haswell and the SandyBridge/Ivybridge
BWGs the save state area actually starts at 0x7c00 offset
from 0x8000. Update the em64t101_smm_state_save_area_t
structure and introduce a define for the offset.
Note: I have no idea what eptp is. It's just listed in the
haswell BWG. The offsets should not be changed.
Change-Id: I38d1d1469e30628a83f10b188ab2fe53d5a50e5a
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2515
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The PCH register bit definition for sleep type is a little confusing.
For example, 7 is S5. To make this simpler for the mainbaord developer,
the mainboard smi sleep hander is called as mainboard_sleep(slp_typ-2).
A couple mainboard SMI handlers were using the PCH define for slp_ty,
so S3 code would be run for S5 and S5 code would never be run.
Change-Id: Iaecf96bfd48cf00153600cd119760364fbdfc29e
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/2514
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Currently some southbridge codes implement the set_ioapic_id() part
locally and do not implement the load_vectors() part at all.
This change allows clean-up of those southbridges without introducing
changed behaviour.
Change-Id: Ic5e860b9b669ecd1e9ddac4bbb92d80bdb9c2fca
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/300
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Mainly replace spaces by tabs and format comments correctly.
Commit »Inagua: Indent and wihtespace cleanup« (f03360f3) [1] was
unfortunately incomplete and also used spaces instead of tabs in
some cases.
Hopefully fix this once and for all to have a template for the
other boards.
[1] http://review.coreboot.org/547
Change-Id: If15c797581dfefe2a57cd6f26e5bdac4cdd014dd
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2526
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Commit »AMD S3: Introduce Kconfig variable 'S3_DATA_SIZE'« (22ec9f9a) [1]
introduced a check throwing an error if S3_DATA_SIZE isn't big enough.
However without CONFIG_HAVE_ACPI_RESUME the variable S3_DATA_SIZE
isn't defined at all and compilation will fail if s3_resume.h is
included.
This patch makes it again possible turn off HAVE_ACPI_RESUME relatively
easily in Parmer/Thatcher/Persimmon's Kconfig if you don't care about S3
and don't want flash writes on every boot.
[1] http://review.coreboot.org/2383
Change-Id: I999e4b7634bf172d8380fd14cba6f7f03468fee3
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: http://review.coreboot.org/2528
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
This patch reduces unnecessary differences between AMD Inagua, Persimmon,
Union Station, South Station and Asrock E350M1. It's only cosmetical, but
makes them a little bit easier to compare.
This is the remainder of the original http://review.coreboot.org/2464,
parts of which somehow got lost in a flurry of refactoring and splitting
patches.
Change-Id: I034228be9edaaa4122506763d7bb4158f8e0ec53
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-on: http://review.coreboot.org/2529
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
This reverts commit ca6e1f6c04.
The packet size changes ends up corrupting the flash when booting
Persimmon. I did figure out that the maximum number of bytes that
can be sent is actually 8 bytes according to the sb800 spec. There
must be additional problems beyond that since setting the packet
size to 8 still causes problems.
Change-Id: Ieb24247cf79e95bb0e548c83601dfddffbf6be59
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/2509
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
Adding RTC init code to the Southbridge initialization
code in 'lpc_init'. This initializes the RTC so that the
Date Alarm register is set to a valid value (0x00) at
startup. By setting the Date Alarm register to 0x00,
it does not get evaluated along with the seconds,
minutes, and hours when running 'fwts s3'.
Information about fwts (Firmware Test Suite) can be
found here:
https://wiki.ubuntu.com/Kernel/Reference/fwts
This is the same edit made to the CIMX SB800 titled
'AMD/Persimmon: Add RTC init to CIMX SB800' with commit
ID: c4d3d which can be viewed here:
http://review.coreboot.org/#/c/2488/
Change-Id: Iddb7a3cbabe736b511cde03d7dc0a4a0b1c7fd90
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2510
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Changes:
- Fix printk warnings for these two platforms by getting rid of the
l length specifier and casting to unsigned int.
This gets rid of a bunch of warnings like this one:
agesawrapper.c:279, GNU Compiler 4 (gcc), Priority: Normal
format '%lu' expects argument of type 'long unsigned int',
but argument 3 has type 'UINT32' [-Wformat]
Notes:
- This is the same change that was done for Tyan s8226 in change:
ddff32eb - http://review.coreboot.org/#/c/2451/
Tyan S8226: Fix printk warnings
- I have not tested this change on either of these platforms, I have
just compiled it.
Change-Id: I46b4c13fde7473cd2a084c7c7cb5c893f1731b02
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2502
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Changes:
- Add #include of delay.h in mainboard.c to pick up declaration of
mdelay function.
Notes:
- This fixes this warning:
mainboard.c:69, GNU Compiler 4 (gcc), Priority: Normal
implicit declaration of function 'mdelay' [-Wimplicit-function-declaration]
Change-Id: I72f333cd87215a7fc1e62d1d7ee4b2395444b03e
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2501
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Currently on for example on AMD Persimmon and ASRock E350M1 Linux
complains, that the PBLK length is invalid [1].
ACPI: Invalid PBLK length [0]
Consequently, frequency scaling might not work correctly, though for
these two boards it seems to work according to PowerTOP.
Indeed, according to the ACPI specification [2], setting PBlockLength
to 0 is only allowed if there is no PBlockAddress. Otherwise it has to
be set to 6.
18.5.93 Processor (Declare Processor)
[…]
PBlockAddress provides the system I/O address for the processors
register block. Each processor can supply a different such
address. PBlockLength is the length of the processor register
block, in bytes and is either 0 (for no P_BLK) or 6. With one
exception, all processors are required to have the same
PBlockLength. The exception is that the boot processor can have
a non-zero PBlockLength when all other processors have a zero
PBlockLength. It is valid for every processor to have a
PBlockLength of 0.
And that is exactly what Linux is checking in
`drivers/acpi/processor_driver.c` [3].
static int acpi_processor_get_info(struct acpi_device *device)
{
[…]
/*
* On some boxes several processors use the same processor bus id.
* But they are located in different scope. For example:
* \_SB.SCK0.CPU0
* \_SB.SCK1.CPU0
* Rename the processor device bus id. And the new bus id will be
* generated as the following format:
* CPU+CPU ID.
*/
sprintf(acpi_device_bid(device), "CPU%X", pr->id);
ACPI_DEBUG_PRINT((ACPI_DB_INFO, "Processor [%d:%d]\n", pr->id,
pr->acpi_id));
if (!object.processor.pblk_address)
ACPI_DEBUG_PRINT((ACPI_DB_INFO, "No PBLK (NULL address)\n"));
else if (object.processor.pblk_length != 6)
printk(KERN_ERR PREFIX "Invalid PBLK length [%d]\n",
object.processor.pblk_length);
else {
pr->throttling.address = object.processor.pblk_address;
pr->throttling.duty_offset = acpi_gbl_FADT.duty_offset;
pr->throttling.duty_width = acpi_gbl_FADT.duty_width;
pr->pblk = object.processor.pblk_address;
/*
* We don't care about error returns - we just try to mark
* these reserved so that nobody else is confused into thinking
* that this region might be unused..
*
* (In particular, allocating the IO range for Cardbus)
*/
request_region(pr->throttling.address, 6, "ACPI CPU throttle");
}
[…]
}
This issue has proliferated to all AMD based boards so fix it for
all of them by setting P_BLK length to 6.
The DSDT of for example AMD Parmer and AMD Thatcher also set it
to 6 everywhere so this solution is taken instead of setting the
P_BLK system I/O base to 0 for all but the first processor which
is how it is done for earlier AMD based boards.
As note having to set this manually should not be needed and
this should be autogenerated as done for most of the Intel boards
and the AMD K8 based boards (`src/cpu/amd/model_fxx/powernow_acpi.c`).
[1] http://www.coreboot.org/pipermail/coreboot/2013-January/073636.html
[2] http://acpi.info/DOWNLOADS/ACPIspec40a.pdf
[3] http://git.kernel.org/?p=linux/kernel/git/torvalds/linux.git;a=blob;f=drivers/acpi/processor_driver.c;h=e83311bf1ebdaaaea1adbf2de1351cca907d3465;hb=5da1f88b8b727dc3a66c52d4513e871be6d43d19#l351
Tested-by: Paul Menzel <paulepanter@users.sourceforge.net>
• ASRock E350M1:
Tested-by: Paul Menzel <paulepanter@users.sourceforge.net>
• AMD Persimmon:
Tested-by: Martin Roth <martin.roth@se-eng.com>
Change-Id: Ie79fe4812532d124cc81747c75a4f3d88d00531c
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2189
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
USB ports 0-4 are handled by PCI devices 12.0 (OHCI) and 12.2 (EHCI). 12.1
simply does not exist, so remove it from devicetree.cb. While at it make the
comment more detailed. Likewise for all USB ports.
USB device 14.6 is the Broadcom GbE MAC integrated in the Hudson-E1. Add it
to devicetree.cb. It's used on Inagua (on), but not on Persimmon (off).
Change-Id: Idea27b3390fa4470f2592e79fdd633d5a218b97b
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-on: http://review.coreboot.org/2463
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
The DSDT header contains the fields OEMID and OEM Table ID. See
for example ACPI specification 4.0a [1]
5.2.11.1 Differentiated System Description Table (DSDT)
on page 135. There Table 5-16 contains the descriptions.
Field Byte Length Byte Offset Description
===================================================
OEMID 6 10 OEM ID
OEM Table ID 8 16 The manufacture model ID.
Currently in coreboot there is no common method what to put in
these fields.
Mostly Intel based boards populate it with "CORE " ore "COREv4"
and AMD based boards populate it with the board vendor and
model number, abbreviated appropriately to fit into these fields.
On most boards the proprietary vendor BIOS seems to leave these
fields – displayed with `sudo dmidecode` under System Information –
blank
To Be Filled By O.E.M.
and fill out the Base Board Information with the board vendor and
model name.
In [2] Jens Rottmann argues that the this is really just the table
ID used for naming it and that »99% of the DSDT code is not board
specific«.
Both approaches seem to have their advantages, but using the
second one, developers often seem to forget to update them (for
example AMD Thather).
The current situation is at least not optimal. and therefore at
least unify the string in the OEM Table ID. If unifying the
OEM ID is also a good idea this should be done too.
If later on it should be decided that the board vendor and model
should be used again, this should be somehow derived from
Kconfig.
The following command was used for the change [3].
$ git grep -l '\/\* TABLE ID \*\/' | xargs sed -i '/TABLE ID/s/"\([^"]*\)"/"COREBOOT"/'
This patch is split out from [2].
[1] http://www.acpi.info/spec40a.htm
[2] http://review.coreboot.org/#/c/2464/
[3] http://stackoverflow.com/questions/5207838/sed-regex-matching-text-between-to-double-quotes-when-a-certain-text-appears-i
Change-Id: Iec98c615ce37f928abc1b500eff5aa865d772cb2
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2472
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
These were not separable or it would have been two CLs.
Enable CHROMEOS configure option on snow. Write gpio support code for
the mainboard. Right now the GPIO just returns hard-wired values for
"virtual" GPIOs.
Add a chromeos.c file for snow, needed to build.
This is tested and creates gpio table entries that our hardware can use.
Lots still missing but we can now start to fill in the blanks, since
we have enabled CHROMEOS for this board. We are getting further into
the process of actually booting a real kernel.
Change-Id: I5fdc68b0b76f9b2172271e991e11bef16f5adb27
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2467
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Similar to the discussion on the coreboot list [1]
Am Freitag, den 22.02.2013, 02:17 +0100 schrieb Peter Stuge:
[…]
> Function names should try to be descriptive. "enable_dev" is not very
> descriptive. I like "mainboard_enable" because it makes output such
> as
>
> printk("%s: foo", __func__);
>
> useful.
rename the function for the northbridge to `northbridge_enable`.
[1] http://www.coreboot.org/pipermail/coreboot/2013-February/074549.html
Change-Id: I262311ec511e394550330214621b8c37780c1d4e
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2496
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
- Fix redefinition warning for SB_GPIO_REG50 introduced in commit
fa8702cf - http://review.coreboot.org/#/c/2446/
Persimmon: adapt PCIe reset code copied from Inagua to actually
match Persimmon
The warning being fixed is:
SB800.h:1491, GNU Compiler 4 (gcc), Priority: Normal
"SB_GPIO_REG50" redefined [enabled by default]
- Enable warnings as errors so no more warnings will be accidentally
committed.
Change-Id: Ib443b2bd2067f0b7d5f93f79170899a0f8f61060
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2494
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
To reduce the differences between these file name the enabling
device function in the directory `src/mainboard` uniformly
`mainboard_enable` [1].
Thanks to the awesome help of gnomon and BlastHardcheese in the
IRC channel #sed on <irc.freenode.net>. gnomon came up with the
following command to do the actual work.
$ cd src/mainboard
$ for f in */*/mainboard.c ; \
> do src="$(awk '/\.enable_dev = /{v=$NF; sub(/,$/,"",v); print v}' "$f")" ; \
> [[ -z $src ]] && continue ; \
> printf '%s\n' "g/${src}/s/${src}\([,(]\)/mainboard_enable\1/p" w | ed -s "$f" ; \
> done
`src/mainboard/digitallogic/msm586seg/mainboard.c` and
`src/mainboard/technologic/ts5300/mainboard.c` had to be adapted
manually as no comma was used separating the struct members.
And with the following statement, gnomon is even more likable!
My pleasure entirely. Good luck with coreboot; I'm a big fan of the project.
[1] http://www.coreboot.org/pipermail/coreboot/2013-February/074548.html
Change-Id: Ife9cd0c2d9cc1ed14afc6d40063450553f06a6c6
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2493
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This is coreboot’s coding style.
Change-Id: I7441f2c1927a49a3b7171112b7798dae6b56cfb5
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2492
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Bernhard Urban <lewurm@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
We don't need the overly complex optimized version, since
we're only doing this in very few non-critical places.
Also, add the div* files to the bootblock, they're needed
if we do printk.
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Change-Id: I83bd766d4b03b488326ade1c13b7c364a7119e7b
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2508
Tested-by: build bot (Jenkins)
This is the common way to name that function, so unify that.
Change-Id: I8a01051bd304039662894b89eed53ce14dde98b6
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2491
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Add brackets around initializer in #define for
PCIE_DDI_DATA_INITIALIZER to fix the warning:
PlatformGnbPcie.c:89, GNU Compiler 4 (gcc), Priority: Normal
missing braces around initializer [-Wmissing-braces]
This warning happens for Inagua and South Station
Change-Id: I7d8f742dd8335b704b0493aa6e9eaebc3cc50b1e
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2495
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Ladies and gentlemen, I'm very happy to announce coreboot support for
the latest and greatest Google Chromebook: The Chromebook Pixel.
See the link below for more information on the Chromebook Pixel, and
its exciting specs:
http://www.google.com/intl/en/chrome/devices/chromebooks.html#pixel
The device is running coreboot and open source firmware on the EC
(see ChromeEC commit for more information on that exciting topic)
Change-Id: I03d00cf391bbb1a32f330793fe9058493e088571
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2482
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reduce unnecessary differences between AMD based boards only
using the file `platform_cfg.h` for configuration making them
a little bit easier to compare.
Inagua & co. mention the board name in several places which are really not
that board specific. Sometimes people even forget to change it:
Union Station’s platform_cfg.h starts with "#ifndef _PERSIMMON_CFG_H_".
Funny. Change that to "_PLATFORM_CFG_H_" everywhere.
The following command was used.
$ find . -name platform_cfg.h | xargs sed -i '/_CFG_H_/s/_.*_/_PLATFORM_CFG_H_/'
More boards seem to use that kind of naming (`git grep _CFG_H_`)
but it is not certain that this will not break anything as for
example the board AMD Dinar also has header files for
configuration stuff for the north- and southbridge.
$ git grep _CFG_H_
[…]
src/mainboard/amd/dinar/platform_cfg.h:#ifndef _PLATFORM_CFG_H_
src/mainboard/amd/dinar/platform_cfg.h:#define _PLATFORM_CFG_H_
src/mainboard/amd/dinar/platform_cfg.h:#endif //_PLATFORM_CFG_H_
src/mainboard/amd/dinar/rd890_cfg.h:#ifndef _RD890_CFG_H_
src/mainboard/amd/dinar/rd890_cfg.h:#define _RD890_CFG_H_
src/mainboard/amd/dinar/rd890_cfg.h:#endif //_RD890_CFG_H_
src/mainboard/amd/dinar/sb700_cfg.h:#ifndef _SB700_CFG_H_
src/mainboard/amd/dinar/sb700_cfg.h:#define _SB700_CFG_H_
src/mainboard/amd/dinar/sb700_cfg.h:#endif //_SB700_CFG_H
[…]
Change-Id: Ida15fa6a7adfc770240ac30e795946000dae3f16
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2464
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Adding RTC init code to the Southbridge initialization
code in 'late.c'. This initializes the RTC so that the
Date Alarm register is set to a valid value (0x00) at
startup. By setting the Date Alarm register to 0x00,
it does not get evaluated along with the seconds,
minutes, and hours when running 'fwts s3'.
Information about fwts (Firmware Test Suite) can be
found here:
https://wiki.ubuntu.com/Kernel/Reference/fwts
This was tested on a Persimmon but will apply to
other mainboards as well.
Change-Id: I9a11bc3f9e3f53c46e7a4d72e62ebb0a4ba1bfe4
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2488
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Google ChromeEC is an EC with completely open source firmware.
See https://gerrit.chromium.org/gerrit/gitweb?p=chromiumos/platform/ec.git;a=summary
for the EC firmware source code (aka more information about the ChromeEC)
This patch adds support for the ChromeEC on coreboot's side.
Great thanks to the ChromeEC team for this amazing work. It's another
important milestone towards a free and open firmware stack on modern
hardware.
Change-Id: Iace78af9d291791d2f5f80ccca1587b418738cec
Signed-off-by: Stefan Reinauer <reinauer@coreboot.org>
Reviewed-on: http://review.coreboot.org/2481
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
At the request of Paul Menzel, I reran an
old classic of a coccinelle script:
@@
expression E;
@@
-(E + 7) & -8
+ALIGN(E, 8)
@@
expression E;
@@
-(E + 15) & -16
+ALIGN(E, 16)
Change-Id: I01da31b241585e361380f75aacf3deddb13d11c3
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/2487
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
There were just whitespace differences and three boards did not
contain
printk(BIOS_DEBUG, "alib\n");
dump_mem(ssdt, ((void *)alib) + alib->length);
which is enclosed `#if DUMP_ACPI_TABLES == 1` to dump the ACPI
tables.
Basically the whitespace in the license header in Inagua’s file
was fixed and then the file copied over to the other directories.
Change-Id: I23f73acad427b5ec14cf51651af67240871f7488
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2470
Tested-by: build bot (Jenkins)
Reviewed-by: Alvaro G. <andor@pierdelacabeza.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The following command was used to correct the typo.
$ git grep -l @breif | xargs sed -i 's/@breif/@brief/'
Change-Id: If0b579279de3c41571b9cda643836f5748a752a2
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2473
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
From ISO C99 standard: »The placement of a storage-class specifier
other than at the beginning of the declaration specifiers in a
declaration is an obsolescent feature.«
Found at <http://www.approxion.com/?p=41>.
Change-Id: Iee7878affb2a5d157a94763083689d75e8218b2f
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2474
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The relational operators in the if-predicate are aligned in all
`dimmSpd.c` files so revert part of the change in
commit 36abff1dc8
Author: Marc Jones <marcj303@gmail.com>
Date: Mon Nov 7 23:26:14 2011 -0700
Cleanup Persimmon mainboard whitespace.
Reviewed-on: http://review.coreboot.org/427
to remove the incorrectly introduced tabs and to unify that. It
might contradict the current coding style but it is even used in
the latest code as seen in the following file.
src/northbridge/amd/agesa/family15tn/dimmSpd.c
Change-Id: Ib611267f99090d0830bdc2319527389f193ea1eb
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2471
Reviewed-by: Alvaro G. <andor@pierdelacabeza.com>
Tested-by: build bot (Jenkins)
This was overlooked in the following commit.
commit 36abff1dc8
Author: Marc Jones <marcj303@gmail.com>
Date: Mon Nov 7 23:26:14 2011 -0700
Cleanup Persimmon mainboard whitespace.
Reviewed-on: http://review.coreboot.org/427
Change-Id: If6bf4836b46077614a04c1e106c241a4f97da166
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2468
Tested-by: build bot (Jenkins)
Reviewed-by: Alvaro G. <andor@pierdelacabeza.com>
For AMD Inagua, the following two commits
commit 01f7ab9335
Author: Kerry Sheh <shekairui@gmail.com>
Date: Thu Jan 19 13:18:36 2012 +0800
Inagua: Synchronize AMD/inagua mainboard.
Reviewed-on: http://review.coreboot.org/542
and
commit d91c9b7e3c
Author: efdesign98 <efdesign98@gmail.com>
Date: Thu Sep 15 10:59:55 2011 -0600
AMD Inagua platform updates
Reviewed-on: http://review.coreboot.org/136
replaced the constant `iobase` is set to by the define `SMBUS0_BASE_ADDRESS` from `OEM.h`.
Do the same for AMD Persimmon, South Station, Union station and ASRock E350M1.
Change-Id: If095cd9d9b28b118b4072c7c9d345bf620b774c9
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2453
Tested-by: build bot (Jenkins)
Currently the size of the volatile storage for S3 reserved in the
image is hardcoded to 32768 bytes. Make that configurable by
introducing the Kconfig 'S3_DATA_SIZE'.
As the storage space is needed for storing non-volatile, volatile and
MTRR data, add a check if the size is big enough.
Change-Id: I9152797cf0045c8da48109a9d760e417717686db
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/2383
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
If CONFIG_CONSOLE_SERIAL is set, and we can call the standard function
and get a non-zero uart address, then we create an lb table entry.
The code was mostly right, just needed a tweak.
Change-Id: I5b36c7b4e580a23319b7ba92cc8ad61592b1757a
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2466
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
For whatever reason tabs got inserted in the license header text.
Remove one occurrence of that with the following command [1].
$ git grep -l 'MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.'$'\t' | xargs sed -i 's,MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.[ ]*,MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.\ \ ,'
[1] http://sed.sourceforge.net/grabbag/tutorials/sedfaq.txt
Change-Id: Iaf4ed32c32600c3b23c08f8754815b959b304882
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2460
Tested-by: build bot (Jenkins)
Reviewed-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-by: Cristian Măgherușan-Stanciu <cristi.magherusan@gmail.com>
The following commit was too eager replacing spaces with tabs.
commit 36abff1dc8
Author: Marc Jones <marcj303@gmail.com>
Date: Mon Nov 7 23:26:14 2011 -0700
Cleanup Persimmon mainboard whitespace.
Reviewed-on: http://review.coreboot.org/427
Fix that with the following command.
$ git grep -l 'Floor, Boston, MA'$'\t''02110-1301 USA' | xargs sed -i 's/Boston, MA[ ]*02110-1301 USA/Boston, MA 02110-1301 USA/'
Change-Id: Ia118a8c19d94ce1f1048280a0f1d49d447cfa2a7
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2461
Tested-by: build bot (Jenkins)
Reviewed-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-by: Cristian Măgherușan-Stanciu <cristi.magherusan@gmail.com>
The SDRAM base is fixed in hardware. It makes no sense to make it configurable.
The TEXT start is a magic number that should also be fixed, not settable.
Change-Id: Ie44cc5c8da1dc38fc00eb602c4a295b045ca5364
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2465
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Payloads, by design, can return. There's lots of mechanism in the payload code
to support it, and the chooser payload relies on it. Hence, we should not mark
the function call in exit_stage as noreturn.
Not all ARM have unified caches, and it's not always easy to tell what
to do. So we are very paranoid. Before we call between stages, we
should carefully flush the dcache to memory and invalidate the icache.
This may be more than is necessary on all architectures but it
doesn't really hurt for the most part.
So compile cache management code into all stages, and call the
flush dcache/invalidate icache from all stages.
Change-Id: Ib9cc625c4dfd2d7d4b3c69a74686cc655a9d6484
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2462
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Fix warning:
mptable.c:52, GNU Compiler 4 (gcc), Priority: Normal
passing argument 3 of 'mptable_write_buses' from incompatible pointer type [enabled by default]
mptable_write_buses is expecting a pointer to an int, so I changed the
U8 isa_bus to an int to match. A U8 doesn't make sense if the value could
be greater than 255 - certainly unlikely, but possible since the value
of isa_bus gets set to the maximum PCI bus number + 1.
Change-Id: I7ea416f48285922d6cf341382109993fd3f6405c
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2450
Tested-by: build bot (Jenkins)
Reviewed-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
Fix Warning:
sb700_cfg.c:129, GNU Compiler 4 (gcc), Priority: Normal
large integer implicitly truncated to unsigned type [-Woverflow]
The issue here was that an 8 bit value was being placed into a 2-bit
bitfield.
$ more src/vendorcode/amd/cimx/sb700/SBTYPE.h
[…]
UINT32 AzaliaSdin0 :2; //6
UINT32 AzaliaSdin1 :2; //8
UINT32 AzaliaSdin2 :2; //10
UINT32 AzaliaSdin3 :2; //12
$ more src/mainboard/tyan/s8226/sb700_cfg.h
[…]
* SDIN0 is define at BIT0 & BIT1
* 00 - GPIO PIN
* 01 - Reserved
* 10 - As a Azalia SDIN pin
* SDIN1 is define at BIT2 & BIT3
* SDIN2 is define at BIT4 & BIT5
* SDIN3 is define at BIT6 & BIT7
*/
#ifndef AZALIA_SDIN_PIN
#define AZALIA_SDIN_PIN 0x2A
#endif
[…]
$ more src/mainboard/tyan/s8226/sb700_cfg.c
[…]
sb_config->AzaliaSdin0 = AZALIA_SDIN_PIN;
[…]
The 8 bit value 0x2A (binary 00 10 10 10), was being used incorrectly
– I believe the original intent of this value was to enable the SDIN
pins 0, 1, & 2. Because it was getting truncated as it was put into
AzaliaSdin0, this wasn't happening and only SDIN0 was being enabled.
I am leaving only SDIN0 enabled at this point to as not change the
actual behavior on the platform.
Change-Id: Icaeb956926309dbfb5af25a36ccb842877e17a34
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2452
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Fix 84 warnings all like this one:
agesawrapper.c:289, GNU Compiler 4 (gcc), Priority: Normal
format '%lu' expects argument of type 'long unsigned int', but argument 3 has type 'UINT32' [-Wformat]
Fixed by getting rid of the l length specifier and casting to unsigned int.
Change-Id: Ic143c1034f760fa5efb2220aa33861e399ddd708
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2451
Tested-by: build bot (Jenkins)
Reviewed-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Looking at AssertSlotReset, the comments and all other case's it's
obvious this is a simple copy & paste error where someone just forgot
to change one occurrance of the GPIO nr. Also the AMD Inagua
schematics show that GPIO02 is what they really meant.
Also forward the fix to boards copied from Inagua (AMD South
Station, Union Station, Asrock E350M1).
Change-Id: I6b9a3d473245fa27604b2f148a730290277a88ed
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-on: http://review.coreboot.org/2445
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
This moves uartmem_getbaseaddr() from an 8250-specific header to the
generic uart header. This is to accomodate non-8250 memory-mapped
UARTs.
Change-Id: Id25e7dab12b33bdd928f2aa4611d720aa79f3dee
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2422
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This adds necessary device operations to add CPU and RAM resources.
Change-Id: Ief8f66627ef37f4fa786bfc3f7899529d3e5b037
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2419
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This patch will cause the resource allocator to actually set aside
the memory resources using methods in the previous patch. The coreboot
table output will include "RAM" entries (there were none before):
coreboot memory table:
0. 0000000040400000-00000000bff001ff: RAM
1. 00000000bff00200-00000000bff00fff: CONFIGURATION TABLES
2. 00000000bff01000-00000000bfffffff: RAM
Change-Id: I5cd76e93fc232fdae1754253efb4e9269b3a20c0
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2420
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
REQUIRES_BLOB assumes that all blob files come from the 3rdparty directory,
builds failed when all files were configured to point to other sources.
This change modifies the blob mechanism so that cbfs-files can be tagged as
"required" with some specification what is missing.
If the configured files can't be found (wrong path, missing file), the build
system returns a list of descriptions, then aborts.
Change-Id: Icc128e3afcee8acf49bff9409b93af7769db3517
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/2418
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marcj303@gmail.com>
S3_DATA_POS defines address where the whole S3 data is stored.
Change-Id: I4155a0821e74a3653caaead890e5fec5677637aa
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/2438
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
This adds a simple loop which initializes the stack to 0xdeadbeef
which is used by checkstack().
Change-Id: I8aecf7bfb1067de68c4080c1fcb7eefa28fd04a7
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2421
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Inagua can use GPIOs 178,179 to switch VMEM to 1.5, 1.35 or 1.25 V,
which it does according to data read from the SO-DIMM's SPD EEPROM.
On Persimmon (according to DB-FT1 rev. D schematics) both GPIOs are
unconnected, there is no way to change the 1.5 V DDR3 voltage (save
unsoldering a resistor). The whole code copied over from Inagua is
useless.
Removed the code, instead a comment hints at Inagua, for people who do designs
based on Persimmon but do have a way to change VMEM.
The line ...->DDR3Voltage = VOLT1_5; is supposed to make the AGESA DDR3 code
select the RAM timings for the actually supplied voltage instead of the
hoped-for but unavailable lower voltage. I have no idea how to test this, but
in any case it can't hurt.
Change-Id: Id098e09418b665645814a6ee2d41a3bff72238ba
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-on: http://review.coreboot.org/2448
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
According to DB-FT1 rev. D schematics the APU PCIe lane 3 is unconnected.
Reflect this fact in the mainboard code.
Change-Id: Ic98f4a63ef971628df7fbf97f56b80ebe7cb8517
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-on: http://review.coreboot.org/2447
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
Comparing Persimmon and Inagua schematics and Coreboot code show the PCIe reset
code has been blindly copied even though it doesn't suit the Persimmon at all.
The Inagua can employ GPIOs 21, 25, 02 to manually reset devices on APU PCIe
lanes 0/1, 2, 3 respectively. (Appearently the motivation for this is to revive
buggy PCIe gen1 devices which got confused by PCIe gen2 signal training.)
However the Persimmon not only doesn't support this, it even needs these 3 pins
for the PCI interface! Instead it uses GPIO50 to reset devices on lanes 0-2 all
at once. Lane 3 is unconnected anyway.
This patch adapts the Persimmon mainboard code according to the DB-FT1 rev. D
schematics.
Change-Id: I05a657d9bf8cc59acc4f5174eb20375165c860c7
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-on: http://review.coreboot.org/2446
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
At least not in menuconfig. Move it after the endchoice.
Change-Id: I87d2f70e7c1fbe539cd78cb602a39335b2886d8d
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-on: http://review.coreboot.org/2443
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
According to spi.c in src/southbridge/amd/agesa/hudson
readwrite = (bytesin + readoffby1) << 4 | bytesout;
We can see that Hudson limits the SPI programming data
packet size as 15.
We used to write data to SPI in dword mode. It didn't
take full advantage of the data packet size. We need to
leverage that to speed up programming time.
Change-Id: I615e3c8e754e58702247bc26cfffbedaf5827ea8
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: Zheng Bao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/2306
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Add needed prototypes to .h files.
Remove unused variables and fix types in printk statements.
Add #IFNDEFs around #DEFINEs to keep them from being defined twice.
Fix a whole bunch of casts.
Fix undefined pre-increment behaviour in a couple of macros. These now
match the macros in the F14 tree.
Change a value of 0xFF that was getting truncated when being assigned
to a 4-bit bitfield to a value of 0x0f.
This was tested with the torpedo build.
This fixes roughly 132 of the 561 warnings in the coreboot build
so I'm not going to list them all.
Here is a sample of the warnings fixed:
In file included from src/cpu/amd/agesa/family12/model_12_init.c:35:0:
src/include/cpu/amd/amdfam12.h:52:5: warning: redundant redeclaration of 'get_initial_apicid' [-Wredundant-decls]
In file included from src/cpu/amd/agesa/family12/model_12_init.c:34:0:
src/include/cpu/amd/multicore.h:48:5: note: previous declaration of 'get_initial_apicid' was here
src/northbridge/amd/agesa/family12/northbridge.c:50:10: warning: no previous prototype for 'get_node_pci' [-Wmissing-prototypes]
src/northbridge/amd/agesa/family12/northbridge.c: In function 'get_hw_mem_hole_info':
src/northbridge/amd/agesa/family12/northbridge.c:302:13: warning: unused variable 'i' [-Wunused-variable]
src/northbridge/amd/agesa/family12/northbridge.c: In function 'domain_set_resources':
src/northbridge/amd/agesa/family12/northbridge.c:587:5: warning: format '%lx' expects argument of type 'long unsigned int', but argument 3 has type 'device_t' [-Wformat]
src/northbridge/amd/agesa/family12/northbridge.c:587:5: warning: format '%lx' expects argument of type 'long unsigned int', but argument 3 has type 'device_t' [-Wformat]
src/northbridge/amd/agesa/family12/northbridge.c:716:1: warning: format '%x' expects argument of type 'unsigned int', but argument 3 has type 'long unsigned int' [-Wformat]
In file included from src/mainboard/amd/torpedo/agesawrapper.h:31:0,
from src/northbridge/amd/agesa/family12/northbridge.c:38:
src/vendorcode/amd/agesa/f12/AGESA.h:1282:0: warning: "TOP_MEM" redefined [enabled by default]
In file included from src/northbridge/amd/agesa/family12/northbridge.c:34:0:
src/include/cpu/amd/mtrr.h:31:0: note: this is the location of the previous definition
In file included from src/mainboard/amd/torpedo/agesawrapper.h:31:0,
from src/northbridge/amd/agesa/family12/northbridge.c:38:
src/vendorcode/amd/agesa/f12/AGESA.h:1283:0: warning: "TOP_MEM2" redefined [enabled by default]
src/vendorcode/amd/agesa/f12/Proc/GNB/Modules/GnbPcieConfig/PcieInputParser.c: In function 'PcieInputParserGetNumberOfComplexes':
src/vendorcode/amd/agesa/f12/Proc/GNB/Modules/GnbPcieConfig/PcieInputParser.c:99:19: warning: operation on 'ComplexList' may be undefined [-Wsequence-point]
src/vendorcode/amd/agesa/f12/Proc/GNB/Modules/GnbPcieConfig/PcieInputParser.c: In function 'PcieInputParserGetLengthOfPcieEnginesList':
src/vendorcode/amd/agesa/f12/Proc/GNB/Modules/GnbPcieConfig/PcieInputParser.c:126:20: warning: operation on 'PciePortList' may be undefined [-Wsequence-point]
src/vendorcode/amd/agesa/f12/Proc/GNB/Modules/GnbPcieConfig/PcieInputParser.c: In function 'PcieInputParserGetLengthOfDdiEnginesList':
src/vendorcode/amd/agesa/f12/Proc/GNB/Modules/GnbPcieConfig/PcieInputParser.c:153:19: warning: operation on 'DdiLinkList' may be undefined [-Wsequence-point]
src/vendorcode/amd/agesa/f12/Proc/GNB/Modules/GnbPcieConfig/PcieInputParser.c: In function 'PcieInputParserGetComplexDescriptorOfSocket':
src/vendorcode/amd/agesa/f12/Proc/GNB/Modules/GnbPcieConfig/PcieInputParser.c:225:17: warning: operation on 'ComplexList' may be undefined [-Wsequence-point]
src/vendorcode/amd/agesa/f12/Proc/GNB/PCIe/Family/LN/F12PciePhyServices.c:246:1: warning: no previous prototype for 'PcieFmForceDccRecalibrationCallback' [-Wmissing-prototypes]
In file included from src/vendorcode/amd/agesa/f12/Proc/GNB/PCIe/Family/LN/F12PcieComplexConfig.c:58:0:
src/vendorcode/amd/agesa/f12/Proc/GNB/PCIe/Family/LN/LlanoComplexData.h:120:5: warning: large integer implicitly truncated to unsigned type [-Woverflow]
And fixed a boatload of these types of warning:
src/vendorcode/amd/agesa/f12/Proc/CPU/heapManager.c: In function 'HeapGetBaseAddress':
src/vendorcode/amd/agesa/f12/Proc/CPU/heapManager.c:687:17: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
src/vendorcode/amd/agesa/f12/Proc/CPU/heapManager.c:694:19: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
src/vendorcode/amd/agesa/f12/Proc/CPU/heapManager.c:701:23: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
src/vendorcode/amd/agesa/f12/Proc/CPU/heapManager.c:702:23: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
src/vendorcode/amd/agesa/f12/Proc/CPU/heapManager.c:705:23: warning: assignment makes integer from pointer without a cast [enabled by default]
src/vendorcode/amd/agesa/f12/Proc/CPU/heapManager.c:709:21: warning: assignment makes integer from pointer without a cast [enabled by default]
Change-Id: I97fa0b8edb453eb582e4402c66482ae9f0a8f764
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2348
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
This cleans out some obsolete Kconfig variables pertaining to IRAM
usage.
Change-Id: Ie53f5f7204eadc3a3dddc739d2b4b6237242b198
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2417
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
This patch fixes up the usage of stack pointer and regions.
The current approach only works by coincidence, so this fixes a few
things at once to get it into a working state and allow us to use
checkstack() again:
- Add a STACK_SIZE Kconfig variable. Earlier on it was evaluated to 0.
- Assign _stack and _estack using CPU-specific Kconfig variables since
it may reside elsewhere in memory (not necessarily DRAM).
- Make the existing IRAM stack variables more useful in this context.
Change-Id: I4ca5b5680c9ea7e26b1b2b6b3890e028188b51c2
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2416
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
Just a mechanical cleanup.
Change-Id: I0815625e629ab0b7ae6c948144085f1bd8cabfb5
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2408
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
We don't need three different implementations.
Change-Id: Ie7b5fa90794676ea38838454a33e8e9188428eb7
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2406
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
s5p-common mostly contained duplicate files, drop the whole directory
and merge the few pieces that we are using into exynos5-common.
Change-Id: I5f18e8a6d2379d719ab6bbbf817fe15bda70d17f
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2405
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
They're unused. Also drop some unused defines in system.h
Change-Id: Ia5afc3a676a4a94787041430f05d08f333033c73
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2404
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Tested-by: build bot (Jenkins)
We don't have asm/
Change-Id: I7f80f47e9d7f457b7a5a64603c59b14d3b536a8c
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2403
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Multiboot is an x86 only thing. Drop support on ARM.
Change-Id: I13fafa464a794206d5450b4a1f23a187967a8338
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2392
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
We don't need SHA in coreboot.
Change-Id: I1985d5e2c74fac39ff9dcdba4c23bb34fa857ec7
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2390
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Tested-by: build bot (Jenkins)
»Chromebook« is the official spelling [1]. So correct that with
the following command.
$ git grep -l ChromeBook | xargs sed -i s,ChromeBook,Chromebook,
The incorrect spelling was only used for the chip name.
[1] http://www.google.com/intl/en/chrome/devices/hp-pavilion-chromebook.html#hp-pav
Change-Id: I9c19f399a3e3d36bd644ec375822daa384a14961
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2370
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Marc Jones <marcj303@gmail.com>
The name lapic_cluster is a bit misleading, since the construct is not local
APIC specific by concept. As implementations and hardware change, be more
generic about our naming. This will allow us to support non-x86 systems without
adding new keywords.
Change-Id: Icd7f5fcf6f54d242eabb5e14ee151eec8d6cceb1
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2377
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
We don't seem to need it, and it currently confuses the payload.
(credit to Gabe Black for this, I'm just uploading it)
Change-Id: I4e3a60eceb9b24e3bc8e50db431c1a731d1cdbae
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/2385
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This was omitted earlier while we were debugging DRAM code (0a5bc7f).
It was likely broken due to inconsistent units earlier on. Now that
things are cleaned up and working, let's add it back in.
Change-Id: I2f356355c98b2896e2371fa63b9c9f20ae76d634
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2379
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
These were left over from earlier debugging and are no longer
needed. They don't indicate any status or useful info (other
than which line of code has been executed). Error messages are
available in case something needs attention.
Change-Id: Ie09fac29c42908cb8924169e56d8927fb76f02da
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2386
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The name pci_domain was a bit misleading, since the construct is only
PCI specific in a particular (northbridge/cpu) implementation, but not
by concept. As implementations and hardware change, be more generic
about our naming. This will allow us to support non-PCI systems without
adding new keywords.
Change-Id: Ide885a1d5e15d37560c79b936a39252150560e85
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2376
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This removes some files leftover from the initial port. Some are
leftover from U-Boot and some were leftover from the skeleton code
derived from x86.
There's a bit more that we'll get in another sweep.
Change-Id: I325793ecb902b3b9430dcf531714ce025d201de6
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2380
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
mmu_setup() was originally written in U-Boot to utilize board-specific
global data. Since we're trying to avoid that, we added start and size
parameters so that board-specific info can be passed in via mainboard
code. Let's start using it that way.
Change-Id: I7d7de0e42bd918c9f9f0c177acaf56c110bf8353
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2378
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
The comment introduced in
commit 50c0a50ac6
Author: David Hendricks <dhendrix@chromium.org>
Date: Thu Jan 31 17:05:50 2013 -0800
armv7: unify stage hand-off routines
Reviewed-on: http://review.coreboot.org/2254
contained a typo, which is corrected now.
Change-Id: I87f7cfa82fcd12b6961d3329e634b4c201cc047e
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2372
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The commit introducing support for the Google Butterfly Chromebook
commit d7bd4eb003
Author: Stefan Reinauer <reinauer@chromium.org>
Date: Mon Feb 11 11:11:36 2013 -0800
Add support for "Butterfly" Chromebook
Reviewed-on: http://review.coreboot.org/2359
contains the typo, which is corrected now.
Change-Id: I932f4cd248cac71c3ede39a7da97162e791827cb
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2373
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Peter Stuge <peter@stuge.se>
Correct some whitespace inconsistencies introduced in the
following commit.
commit d7bd4eb003
Author: Stefan Reinauer <reinauer@chromium.org>
Date: Mon Feb 11 11:11:36 2013 -0800
Add support for "Butterfly" Chromebook
Reviewed-on: http://review.coreboot.org/2359
Change-Id: Ifeda7eb29ddf855cdfea41ddbd685441ede55756
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2374
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
The commits adding support for the Google Parrot Chromebook
commit a7198b34cc
Author: Stefan Reinauer <reinauer@chromium.org>
Date: Tue Dec 11 16:00:47 2012 -0800
Add support for Google Parrot Chromebook
Reviewed-on: http://review.coreboot.org/2026
and the Google Butterfly Chromebook
commit d7bd4eb003
Author: Stefan Reinauer <reinauer@chromium.org>
Date: Mon Feb 11 11:11:36 2013 -0800
Add support for "Butterfly" Chromebook
Reviewed-on: http://review.coreboot.org/2359
had macros in `fadt.c` which were not aligned correctly and did
not adhere to the coding style which uses just one space after
`#define`. Fix this and use tabs instead of spaces everywhere.
Change-Id: I1422c57a3bdc2faa29d2a6e2064e4d3aeed0f1cb
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2375
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
The order of some printk arguments were reversed.
Change-Id: I5e8f70b79050b92ebe8cfa5aae94b6cd1a5fd547
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2364
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This is just to get us to the payload.
TODO: Do we want to implement any of the stuff from the x86 version,
such as copying coreboot to a new location?
Change-Id: Ia0544f111d7a1189ebd92d0ba3e11448eabd6252
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2363
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
To simplify testing ARM implementation, we need a QEMU configuration for
ARM. The qemu-armv7 provides serial output, CBFS simulation, and full
boot path (bootblock, romstage, ramstage) to verify the boot loader
functionality.
To run with QEMU:
export QEMU_AUDIO_DRV=none
qemu-system-arm -M vexpress-a9 -m 1024M -nographic -kernel build/coreboot.rom
Verified to boot until ramstage loaded successfully by QEMU v1.0.50.
Change-Id: I1f23ffaf408199811a0756236821c7e0f2a85004
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2354
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Rename _SPI_H_ to _SPI_GENERIC_H_ to match recent file rename.
Change-Id: I8b75e2e0a515fb540587630163ad289d0a6a0b22
Reported-by: Peter Stuge <peter@stuge.se>
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/2360
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
We're happy to announce coreboot support for the "Butterfly"
Chromebook, a.k.a HP Pavilion Chromebook.
More information at:
http://www.google.com/intl/en/chrome/devices/hp-pavilion-chromebook.html
This commit also includes support for the ENE KB3940Q embedded controller
running on Quanta's firmware.
Change-Id: I194f847a94005218ec04eeba091c3257ac459510
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2359
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins)
It was off by a few orders of magnitude. D'oh.
Change-Id: I9c8a3d5bd9ce261f914cfc7d05d86a1c61519b81
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2355
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Since there are and will be other files in nb/sb folders, we change
the general spi.h to a file name which is not easy to be duplicated.
Change-Id: I6548a81206caa608369be044747bde31e2b08d1a
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/2309
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
And move the corresponding #define to speedstep.h
Change-Id: I8c884b8ab9ba54e01cfed7647a59deafeac94f2d
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/2339
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The hardware is there, so turn it on.
Change-Id: I40aff1e84a22a05599c62b9f0b20397df0a40b15
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/2353
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
MMCONF space is defined by two config parameters:
MMCONF_BASE_ADDRESS (0xF800 0000)
MMCONF_BUS_NUMBER (64)
Coreboot allocates 1MB per bus, so MMCONF limit should be:
0xF800 0000 + 64*(0x0010 0000) - 1 = 0xFBFF FFFF
Current code does not have (-1) component, this makes MMCONF limit
equal 0xFC00 FFFF. Not 0xFC00 0000, because according to BKDG
lower two bytes of MMIO limit always equal 0xFFFF:
MMIOLimit = {MMIOLimitRegister[47:16], FFFFh}.
Add (-1) to correct this issue.
No functionality change has been experienced. The five times
slower RAM speed compared to the proprietary vendor BIOS still
remains.
Change-Id: I2c6494c28bb8d36e54ceb2aa7d8d965b0103cbe9
Signed-off-by: Konstantin Aladyshev <aladyshev@nicevt.ru>
Reviewed-on: http://review.coreboot.org/2193
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Add a prototype to a .h file
Remove an unused file (GppHp.c) from the build by deleting it from the
makefile. I left the file since this is vendorcode. This is the code
for PCIe hotplug.
Inside GppHp.c, make functions not called from outside static.
This obviously isn't important since the file isn't used, but for
the sake of the cleanup I thought I'd go ahead with it...
This was tested with the torpedo build.
This fixes these warnings:
src/vendorcode/amd/cimx/sb900/Dispatcher.c: In function 'LocateImage':
src/vendorcode/amd/cimx/sb900/Dispatcher.c:193:38: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
src/vendorcode/amd/cimx/sb900/Usb.c:740:1: warning: no previous prototype for 'XhciA12Fix' [-Wmissing-prototypes]
src/vendorcode/amd/cimx/sb900/GppHp.c:65:1: warning: no previous prototype for 'sbGppHotPlugSmiProcess' [-Wmissing-prototypes]
src/vendorcode/amd/cimx/sb900/GppHp.c: In function 'sbGppHotPlugSmiProcess':
src/vendorcode/amd/cimx/sb900/GppHp.c:76:5: warning: implicit declaration of function 'SbStall' [-Wimplicit-function-declaration]
src/vendorcode/amd/cimx/sb900/GppHp.c: At top level:
src/vendorcode/amd/cimx/sb900/GppHp.c:101:1: warning: no previous prototype for 'sbGppHotUnplugSmiProcess' [-Wmissing-prototypes]
src/vendorcode/amd/cimx/sb900/GppHp.c:134:1: warning: no previous prototype for 'sbGppHotplugSmiCallback' [-Wmissing-prototypes]
src/vendorcode/amd/cimx/sb900/GppHp.c: In function 'sbGppHotplugSmiCallback':
src/vendorcode/amd/cimx/sb900/GppHp.c:158:5: warning: implicit declaration of function 'outPort80' [-Wimplicit-function-declaration]
Change-Id: I5a1a20eeb81e1f4d59e3e3192f081e11d8506f56
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2349
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
It has worked up to now because the region is already erased
the first time the board boots, and every additional boot the
same data is being written over the old data.(by Dave Frodin)
Change-Id: Id334c60668e31d23c1d552d0ace8eb6ae5513e6b
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/2304
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This will make the build script wipe out more flash memory content.
Our image is a bit bigger now that we're testing with payloads, so
this is just added paranoia to prevent weird surprises caused by not
flashing the full image.
Change-Id: I31969922079e96886573d9d802266eb0052277cd
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2352
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
RAMBASE and RAMTOP are leftovers from the x86 port and do not apply
the same way on ARM platforms. On x86 they refer to the low memory
region where coreboot tables reside.
However on ARM we don't have such a region which is architecturally
defined. So instead we'll use the CPU-defined DRAM base address and
the mainboard-defined DRAM size.
This also has the pleasant side-effect of fixing the coreboot tables
to not clobber ramstage code...
Change-Id: I5548ecf05e82f9d9ecec8548fabdd99cc1e39c3b
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2351
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
For Exynos/snow, cpu_info and power modules and also some parts of
the GPIO API (which require timer and pwm modules) are not used in the
current bootblock. Clock init only needs to be used if early console
is enabled.
Now our bootblock is 22420 bytes with early serial console and 11192
bytes without. Those include the 8KB BL1 region.
Change-Id: I9c958dafb9cf522df0dcfbef373ce741aa162544
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2322
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This moves GPIO setup from chip-specific SPI code to mainboard-
specific bootblock code. This makes exynos_spi_open a bit more
generic so it can eventually be used for any SPI channel. This
also benefits CBFS since the user can set media->context to
to any set of SPI registers.
Change-Id: I2bcb9de370df0a79353c14b4d021b471ddebfacd
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2347
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This moves the setting of SPI clock rate into romstage's main,
which allows us to eliminate a bunch of dependencies from the
bootblock (about 7KB worth).
Change-Id: I371499bb4af6a6aa838294bc56f9dbc21864957a
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2346
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This places the .id section toward the lower region of the coreboot
image, before the bootblock. It's easier for humans to find by dumping
the image and it also eliminates ID_SECTION_OFFSET which is currently
the upper bound on our image size.
Change-Id: I7d737b901dac659ddf9aa437cee5dc32f1080546
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2345
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This adds a .bl1 and .start symbol that is placed at the beginning
of the .rom section.
The goal is to move the .id section in between the reset vector and
bootblock_main.
Change-Id: Ie732ce656d697c059cc0fa40c844b39f53fc214c
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2344
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The Kconfig variable indicates KB, but the number used was bytes.
Let's just assume KB is correct for now.
Change-Id: I910c126104f0222fc48b70a18df943f2afddeca3
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2341
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Except for one board, the flags can be derived from CONFIG_MMX
and CONFIG_SSE.
Change-Id: I64a11135ee7ce8676f3422b2377069a3fa78e24d
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/2336
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The bootblock is typically run before fpu/mmx/sse setup, so
we can't rely on -mcpu=p4 and the like to increase the
register space.
bootblock_romccflags does that for SSE, but they're controlled
separately.
Change-Id: I2b0609ac18b2394a319bf9bbbee1f77d2e758127
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/2335
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This is a first-pass attempt at cleaning up the coreboot tables
for ARM. The most noticable difference is that there is no longer
both a high and a low table.
Change-Id: I5ba87ad57bf9a697b733511182c0326825071617
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2329
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This cleans up Snow's trivial ramstage, gives it a coreboot table
address and calls hardwaremain().
Change-Id: I84c904bcfd57a5f9eb3969de8a496f01e43bc2f6
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2328
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This adds a BL1_SIZE_KB config variable so that we can get rid of
some magic constants.
Change-Id: I9dbcfb407d3f8e367be5d943e95b032ce88b0ad0
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2332
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Explicitly including it allows us to get rid of some magic constants
in the bootblock linker script.
Change-Id: I095899babc997addce6b383f00e5ebf135e99d5e
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2331
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This seemed to have been introduced in fe422184.
Change-Id: I4f9ecfbec42aa8c0bb8887675a3add8951645b98
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2327
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Add a comment explaining that the existing lock bit logic is correct
and "as designed" even though the manual states otherwise. This way
people don't have to "just know" what is going on.
Change-Id: I14e6763abfe339e034037b73db01d4ee634bb34d
Signed-off-by: Mike Frysinger <vapier@chromium.org>
Reviewed-on: http://review.coreboot.org/2326
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
This hit me when running the latest Qemu with coreboot:
First the graphics OPROM is running, then an iPXE OPROM.
The iPXE OPROM has no int10 support (obviously) so calling
vbe_set_graphics() wipes the framebuffer information from
the coreboot table.
Change-Id: Ie0453c4a908ea4a6216158f663407a3e72ce4d34
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2325
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Just a tiny mistake, but it made the console driver assume that
CMOS data isn't available.
Change-Id: I4e6f53e9ed59024de7b09333f82f0ce3235ef8f6
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/2323
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
Not sure why this didn't bite us earlier..
src/device/oprom/realmode/x86.c: In function 'fill_lb_framebuffer':
src/device/oprom/realmode/x86.c:272:13: error: dereferencing pointer to incomplete type
src/device/oprom/realmode/x86.c:274:13: error: dereferencing pointer to incomplete type
src/device/oprom/realmode/x86.c:275:13: error: dereferencing pointer to incomplete type
src/device/oprom/realmode/x86.c:276:13: error: dereferencing pointer to incomplete type
src/device/oprom/realmode/x86.c:278:13: error: dereferencing pointer to incomplete type
src/device/oprom/realmode/x86.c:280:13: error: dereferencing pointer to incomplete type
src/device/oprom/realmode/x86.c:281:13: error: dereferencing pointer to incomplete type
src/device/oprom/realmode/x86.c:283:13: error: dereferencing pointer to incomplete type
src/device/oprom/realmode/x86.c:284:13: error: dereferencing pointer to incomplete type
src/device/oprom/realmode/x86.c:286:13: error: dereferencing pointer to incomplete type
src/device/oprom/realmode/x86.c:287:13: error: dereferencing pointer to incomplete type
src/device/oprom/realmode/x86.c:289:13: error: dereferencing pointer to incomplete type
src/device/oprom/realmode/x86.c:290:13: error: dereferencing pointer to incomplete type
Change-Id: Ie3b0f731a7b995e954a26e745b07fc122088ca9f
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2321
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Exynos system clock can be initialized before RAM init, not necessary to be in
the very beginning (boot block). This helps reducing bootblock dependency.
Verified to boot on armv7/snow.
Note: this patch was originally introduced in 2308, but there were
some ordering issues so it was reverted.
Change-Id: Ibc91c0e26ea8881751fc088754f5c6161d011b68
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2320
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Use same console initialization procedure for all ARM stages (bootblock,
romstage, and ramstage):
#include <console/console.h>
...
console_init()
...
printk(level, format, ...)
Verified to boot on armv7/snow with console messages in all stages.
Change-Id: Idd689219035e67450ea133838a2ca02f8d74557e
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2301
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Revise console source file dependency (especially for EARLY_CONSOLE) and
interpret printk/console_init according to EARLY_CONSOLE setting (no-ops if
EARLY_CONSOLE is not defined).
Verified to boot on x86/qemu and armv7/snow. Disabling EARLY_CONSOLE correctly
stops romstage messages on x86/qemu (armv7/snow needs more changes to work).
Change-Id: Idbbd3a26bc1135c9d3ae282aad486961fb60e0ea
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2300
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Early console should always be allowed to be turned on / off (for generating
production and debug versions), and should not be enforced by "select" Kconfig
rule.
A new "DEFAULT_EARLY_CONSOLE" is introduced for devices to select if they
prefer early console output by default.
Verified Kconfig value on qemu/x86 (default y by CACHE_AS_RAM), snow/x86
(default y by EXYNOS5 config), and intel/jarrell (default n).
Change-Id: Ib1cc76d4ec115a302b95e7317224f1a40d1ab035
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2307
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: David Hendricks <dhendrix@chromium.org>
For Exynos platforms, the UART component on pinmux must be first selected and
configured. This should be done as part of UART console initialization.
Note, that the current implementation hard-codes the device index as UART3,
while the base port can be assigned to different device in Kconfig. This will be
fixed later.
Verified to work on armv7/snow.
Change-Id: Ie63e76e2dac09fec1132573d1b0027fce55333a1
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2315
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: David Hendricks <dhendrix@chromium.org>
The console drivers (especially serial drivers) in Kconfig were named in
different styles. This change will rename configuration names to a better naming
style.
- EARLY_CONSOLE:
Enable output in pre-ram stage. (Renamed from EARLY_SERIAL_CONSOLE
because it also supports non-serial)
- CONSOLE_SERIAL:
Enable serial output console, from one of the serial drivers. (Renamed
from SERIAL_CONSOLE because other non-serial drivers are named as
CONSOLE_XXX like CONSOLE_CBMEM)
- CONSOLE_SERIAL_UART:
Device-specific UART driver. (Renamed from
CONSOLE_SERIAL_NONSTANDARD_MEM because it may be not memory-mapped)
- HAVE_UART_SPECIAL:
A dependency for CONSOLE_SERIAL_UART.
Verified to boot on x86/qemu and armv7/snow, and still seeing console
messages in romstage for both platforms.
Change-Id: I4bea3c8fea05bbb7d78df6bc22f82414ac66f973
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2299
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
This reverts commit 9029f4b63f
This patch needs to go at the end of the UART patch set. Sorry 'bout the confusion!
Change-Id: I5702c7d6130daf95776f2c15d24e5d253691cefd
Reviewed-on: http://review.coreboot.org/2319
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Exynos system clock can be initialized before RAM init, not necessary to be in
the very beginning (boot block). This helps reducing bootblock dependency.
Verified to boot on armv7/snow.
Change-Id: Ic863e222871a157ba4279a673775b1e18c6eac0d
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2308
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
The prototypes that were recently defined only work for the
internal implementations.
Change-Id: Ib34bb75a0b882533da550b9cd17cd777c2463e02
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/2318
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The power_init is not required on Exynos 5250 (snow) in bootblock stage. To get
a cleaner and faster bootblock, we can remove it.
Note, power_init internally calls max77686 and s3c24x0_i2c, so both files are
also removed.
Verified to boot on armv7/snow.
Change-Id: I5b15dfe5ac7bf4650565fea0afefc94a228ece29
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2317
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The I2C initialization (on component MAX77688) is already done in power_init, so
we should not need an explicit call inside bootblock.
Verified to boot on armv7/snow.
Change-Id: I68c248a8b5fee4ab838b2fb708649e112559cc41
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2316
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Remove duplicated / testing code and share more driver for bootblock, romstage
and ramstage.
The __PRE_RAM__ is now also defined in bootblock build stage, since bootblock is
executed before RAM is initialized.
Change-Id: I4f5469b1545631eee1cf9f2f5df93cbe3a58268b
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2282
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
For x86, the old CBFS search behavior was to bypass bootblock and we should keep
that. This will speed up searching if a file does not exist in CBFS.
For arm, the size in header is correct now so we can remove the hack by
CONFIG_ROM_SIZE.
Change-Id: I541961bc4dd083a583f8a80b69e293694fb055ef
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2292
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
"SPL" from U-Boot is deprecated by bootblock in coreboot/arm, so we don't need
it anymore.
Change-Id: Id16877075d0b870839a10160073ad70777a2af0a
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2297
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This attempts to clean out some dead code which was copy + pasted
into Snow's bootblock.c file, along with some unnecessary headers.
Change-Id: If9f157a52395a047c249a2a6385e0e8ddf310e59
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2291
Tested-by: build bot (Jenkins)
hang() is the legacy function from U-boot and should be replaced by hlt() in
coreboot.
Change-Id: I0f390b1b6f9ff71487ea36cf16c462724b66d8ca
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2298
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Added casts and a couple of #ifdefs to fix the warnings in the
vendorcode/amd/agesa/f14 codebase. This will allow us to re-enable
'all warnings being treated as errors' in boards such as Persimmon
that are using this code. That change will follow.
These are the warnings that are fixed by this patch:
src/vendorcode/amd/agesa/f14/Legacy/Proc/hobTransfer.c: In function 'CopyHeapToTempRamAtPost':
src/vendorcode/amd/agesa/f14/Legacy/Proc/hobTransfer.c:219:28: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
src/vendorcode/amd/agesa/f14/Legacy/Proc/hobTransfer.c: In function 'CopyHeapToMainRamAtPost':
src/vendorcode/amd/agesa/f14/Legacy/Proc/hobTransfer.c:372:30: warning: comparison between pointer and integer [enabled by default]
src/vendorcode/amd/agesa/f14/Legacy/Proc/hobTransfer.c:381:33: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
src/vendorcode/amd/agesa/f14/Proc/CPU/cpuApicUtilities.c: In function 'ApUtilSetupIdtForHlt':
src/vendorcode/amd/agesa/f14/Proc/CPU/cpuApicUtilities.c:863:19: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
src/vendorcode/amd/agesa/f14/Proc/CPU/cpuApicUtilities.c:872:18: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
src/vendorcode/amd/agesa/f14/Proc/CPU/cpuMicrocodePatch.c: In function 'LoadMicrocode':
src/vendorcode/amd/agesa/f14/Proc/CPU/cpuMicrocodePatch.c:211:28: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
src/vendorcode/amd/agesa/f14/Proc/CPU/heapManager.c: In function 'HeapManagerInit':
src/vendorcode/amd/agesa/f14/Proc/CPU/heapManager.c:167:52: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
src/vendorcode/amd/agesa/f14/Proc/CPU/heapManager.c:183:14: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
src/vendorcode/amd/agesa/f14/Proc/CPU/heapManager.c: In function 'HeapGetBaseAddress':
src/vendorcode/amd/agesa/f14/Proc/CPU/heapManager.c:669:17: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
src/vendorcode/amd/agesa/f14/Proc/CPU/heapManager.c:676:19: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
src/vendorcode/amd/agesa/f14/Proc/CPU/heapManager.c:683:23: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
src/vendorcode/amd/agesa/f14/Proc/CPU/heapManager.c:684:23: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
src/vendorcode/amd/agesa/f14/Proc/CPU/heapManager.c:687:23: warning: assignment makes integer from pointer without a cast [enabled by default]
src/vendorcode/amd/agesa/f14/Proc/CPU/heapManager.c:691:21: warning: assignment makes integer from pointer without a cast [enabled by default]
src/vendorcode/amd/agesa/f14/Proc/CPU/heapManager.c:696:3: warning: return makes pointer from integer without a cast [enabled by default]
In file included from src/mainboard/amd/persimmon/agesawrapper.h:30:0,
from src/northbridge/amd/agesa/family14/northbridge.c:36:
src/vendorcode/amd/agesa/f14/AGESA.h:1132:0: warning: "TOP_MEM" redefined [enabled by default]
In file included from src/northbridge/amd/agesa/family14/northbridge.c:34:0:
src/include/cpu/amd/mtrr.h:31:0: note: this is the location of the previous definition
In file included from src/mainboard/amd/persimmon/agesawrapper.h:30:0,
from src/northbridge/amd/agesa/family14/northbridge.c:36:
src/vendorcode/amd/agesa/f14/AGESA.h:1133:0: warning: "TOP_MEM2" redefined [enabled by default]
In file included from src/northbridge/amd/agesa/family14/northbridge.c:34:0:
src/include/cpu/amd/mtrr.h:34:0: note: this is the location of the previous definition
Verified on persimmon.
Change-Id: I1671b191c72dfc1d63ada41126ae3418bc8f86ae
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2293
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Steven Sherk <steven.sherk@se-eng.com>
The common part of the bootblock resets the nvram data if it's found
to be invalid. Since that code is compiled with romcc in i386 mode,
there's a shortage on registers.
Try to reduce the strain by doing things smarter: cmos_write_inner
is the same as cmos_write, just that it doesn't check if the RTC is
disabled. Since we just disabled it before, we can assume that it is so.
Change-Id: Ic85eb2a5df949d1c1aff654bc1b40d6f2ff71756
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/2296
Tested-by: build bot (Jenkins)
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
For arm/snow, current bootblock is larger than previously assigned CBFS offset
and will fail to boot. To prevent this happening again in future, cbfstool now
checks if CBFS will overlap bootblock.
A sample error message:
E: Bootblock (0x0+0x71d4) overlap CBFS data (0x5000)
E: Failed to create build/coreboot.pre1.tmp.
arm/snow offset is also enlarged and moved to Kconfig variable.
Change-Id: I4556aef27ff716556040312ae8ccb78078abc82d
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2295
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Some variables are using incorrect data type in debug messages.
Also corrects a typo (extra 'x').
Change-Id: Ia3014ea018f8c1e4733c54a7d9ee196d0437cfbb
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2294
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
This patch moves ARM core and DRAM timing functions around to simplify
the dependencies for system_clock_init().
The original code was architected such that the system_clock_init()
function called other functions to obtain core and memory timings.
Due to the way memory timing information must be obtained on Snow,
which entails decoding platform-specific board straps, the bottom-
up approach resulted in having the low-level clock init code
implicitly depend on board and vendor-specific info:
main()
->system_clock_init()
-> get_arm_ratios()
-> CPU-specific code
-> clock_get_mem_timings()
-> board_get_revision()
-> read GPIOs (3-state logic)
-> Decode GPIOs in a vendor-specific manner
-> Choose memory timings from module-specific look-up table
...then proceed to init clocks
...come back to main()
The new approach gathers all board and vendor-specific info in a
more appropriate location and passes it into system_clock_init():
main()
-> get_arm_ratios()
-> CPU-specific code
-> get_mem_timings()
-> board_get_config()
-> read GPIOs (3-state logic)
-> Decode GPIOs in a vendor-specific manner
-> Choose memory timings from module-specific look-up table
-> system_clock_init()
...back to main()
Change-Id: Ie237ebff76fc2d8a4d2f4577a226ac3909e4d4e8
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2271
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This gets rid of a bunch of duplicate I2C code in the bootblock.
Change-Id: I51f625a0f738cca4ed2453fbcb78092e4110bc7e
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2289
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This gets rid of a bunch of copy + pasted GPIO code.
Change-Id: I548b2b5d63642a9da185eb7b34f80cbebf9b124f
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2288
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Move the ID section again due to bootblock bloat. So long
as it's within the first 32K of our address space, we're good.
TODO:
1. Place ID section near start of ROM to avoid this issue.
2. Reduce bootblock bloat.
3. Make bootblock debugging a Kconfig option.
Change-Id: I3f0764a3345a8cbbafcc15e4d06c38cd6327758c
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2287
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
We don't need a special Kconfig variable anymore
because the FV _is_ the payload, unlike with the
old tianocoreboot implementation.
Change-Id: I349b5a95783e4146e3ab7f926871188cf2021935
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2284
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
This gets rid of a bunch of copy + pasted code from Exynos UART
files.
Change-Id: I9fbb6d79a40a338c9fdecd495544ff207909fd37
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2286
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
Some header content got duplicated during the initial porting
effort. This moves generic UART header stuff to exynos5-common
and leaves exynos5250 #defines in the AP-specific UART header.
Change-Id: Ifb6289d7b9dc26c76ae4dfcf511590b3885715a3
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2285
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This removes the hack implemented in http://review.coreboot.org/#/c/2280
(and should make using 64bit Tiano easier, but that's not yet supported)
Change-Id: Ie30129c4102dfbd41584177f39057b31f5a937fd
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2281
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Usage Changes: To support platforms with different memory layout, "create" takes
two extra optional parameters:
"-b": base address (or offset) for bootblock. When omitted, put bootblock in
end of ROM (x86 style).
"-H": header offset. When omitted, put header right before bootblock,
and update a top-aligned virtual address reference in end of ROM.
Example: (can be found in ARM MAkefile):
cbfstool coreboot.rom create -m armv7 -s 4096K -B bootblock.bin \
-a 64 -b 0x0000 -H 0x2040 -o 0x5000
Verified to boot on ARM (Snow) and X86 (QEMU).
Change-Id: Ida2a9e32f9a459787b577db5e6581550d9d7017b
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2214
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
To support platforms without top-aligned address mapping like ARM, "locate"
command now outputs platform independent ROM offset by default. To retrieve x86
style top-aligned virtual address, add "-T".
To test:
cbfstool coreboot.rom locate -f stage -n stage -a 0x100000 -T
# Example output: 0xffffdc10
Change-Id: I474703c4197b36524b75407a91faab1194edc64d
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2213
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This is a port of the following:
commit d5c998be99
The coreboot resource allocator doesn't respect resources
claimed in the APIC_CLUSTER. Move the MMCONF resource to the
PCI_DOMAIN to prevent overlap with PCI devices.
original-Change-Id: I8541795f69bbdd9041b390103fb901d37e07eeb9
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
URL - http://review.coreboot.org/#/c/2167/
Change-Id: I6e585d5cf0d46bd58337a6801fb0690ab2dd000c
Signed-off-by: Steven Sherk <steven.sherk@se-eng.com>
Reviewed-on: http://review.coreboot.org/2248
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
This unplugs Stefan's PIANO project.
Change Tianocore payload configuration to use corebootPkg.
As argument you have to give it the COREBOOT.FD generated by
the Tianocore build system.
It automatically determines base address and entry point.
Compression setting is honored (ie. no compression if you don't
want), but corebootPkg currently assumes that coreboot is doing
it. Loading a 6MB payload into CBFS without compression will fail
more often than not.
Change-Id: If9c64c9adb4a846a677c8af40f149ce697059ee6
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/2280
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The following command was used to correct the grammatical mistake.
$ git grep -l 'This is the stub function will call' | xargs sed -i s,This is the stub function will call,This stub function will call, '{}'
sed: -e Ausdruck #1, Zeichen 6: Nicht beendeter `s'-Befehl
As this file seems to have been copied around a lot, it originally
seems to have come with the following commit for AMD Persimmon and
AMD Inagua.
commit 69da1b676c
Author: Frank Vibrans <frank.vibrans@amd.com>
Date: Mon Feb 14 19:04:45 2011 +0000
Add IBASE DB-FT1 and AMD Inagua motherboards. Patch 8 of 8.
Change-Id: I2e6630a5172738b01e6def7062284f167e5508b1
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2268
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
If somebody makes use of CONFIG_LOCALVERSION show this
user provided config string for DMI bios_version.
As requested I have attached example output.
CONFIG_LOCALVERSION=""
CONFIG_CBFS_PREFIX="fallback"
CONFIG_COMPILER_GCC=y
...
root@OT:~# cat /sys/class/dmi/id/bios_version
4.0-3360-g5be6673-dirty
CONFIG_LOCALVERSION="V1.01.02 Beta"
CONFIG_CBFS_PREFIX="fallback"
CONFIG_COMPILER_GCC=y
...
root@OT:~# cat /sys/class/dmi/id/bios_version
V1.01.02 Beta
Change-Id: I5640b72b56887ddf85113efa9ff23df9d4c7eb86
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-on: http://review.coreboot.org/2279
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Marc Jones <marcj303@gmail.com>
Update function messages to be more portable by using
the __func__ compiler command instead of hard coded
function names.
Change-Id: I3368a831770df1b8449eb0c97ae4bb24f6678efd
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2250
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
Update function messages to be more portable by using
the __func__ compiler command instead of hard coded
function names.
Change-Id: Ib8ab97666340a9481f3ab71f0f347382e964994f
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2251
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
Update function messages to be more portable by using
the __func__ compiler command instead of hard coded
function names.
Change-Id: Idf479980e427bbf0399bdbc15045d80f402f6dbe
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2249
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
Update function messages to be more portable by using
the __func__ compiler command instead of hard coded
function names.
Change-Id: Ie71fec39df5e7703d35d6505dc7d5b55179e2c7e
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2234
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
In the process of verifying change it was discovered the MMCONF
default base address 0xA0000000 was set below mem_top 0xE0000000
and bus number 256 wasn't a relistic number. The Kconfig defaults were
changed to mirror fam15 defaults base address 0xF8000000 and bus
number 64. Verified changes with boot to OS.
This is a port of the following:
commit d5c998be99
The coreboot resource allocator doesn't respect resources
claimed in the APIC_CLUSTER. Move the MMCONF resource to the
PCI_DOMAIN to prevent overlap with PCI devices.
original-Change-Id: I8541795f69bbdd9041b390103fb901d37e07eeb9
Signed-off-by: Marc Jones <marc.jones@se-eng.com
URL - http://review.coreboot.org/#/c/2167/
Change-Id: I47660061538f8889f528b9b880a82645074886a7
Signed-off-by: Steven Sherk <steven.sherk@se-eng.com>
Reviewed-on: http://review.coreboot.org/2260
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
AOpen DXPL Plus-U and Intel XE7501devkit use »COREBOOT« as
OEM Table ID.
Unify the DSDT by aligning the comments in the DSDT header with
tabs in accordance with the coding style [1].
[1] http://www.coreboot.org/Development_Guidelines#Coding_Style
Change-Id: I78e6aa8d0318b519b1df5e2178d387dc58e48323
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2278
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Mainboards using `COREBOOT` as their OEM Table ID in their DSDT
header were copied from the same source and therefore had spaces
instead of a tab to align that comment for that header field. These
are mostly Intel based boards.
Fix that in accordance with the coding style [1].
[1] http://www.coreboot.org/Development_Guidelines#Coding_Style
Change-Id: I299b955930dbd50b9717e8ff141ce8f3fd534e5f
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2277
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
This file has mostly (but not entirely) been replaced by coreboot
stage files. We'll keep it around for a bit longer as a reference,
but in the meantime we'll stop compiling it as to avoid comptilation
issues as we change other parts of the code.
Change-Id: I669fb1e5a1517f35979590957d581bd33df53d29
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2269
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Snow's AP, EC, PMU, and smarty battery share a bus. Both the AP and
EC can act as a master, so to avoid conflicts an arbitration
mechanism consisting of two GPIOs is used.
By default, the AP "owns" the bus unless it is off (in which case
the EC doesn't monitor the arbitration pins). This means the boot
firmware does not need to worry about these lines. The payload may
if it needs to communicate with the EC, though.
In any case, board-specific bus arbitration logic does not belong
in a low-level driver that is supposed to be generic for an entire
CPU family. If the payload needs to talk to the EC, we'll deal with
it there.
Change-Id: I0774d4592af2b21b6ad668441532c5ceab988404
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2272
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This removes some duplicate code from Snow's mainboard bootblock
by utilizing the bootblock build class.
Change-Id: I153247370a8c5127260082dcdca3ebdc5e104fb8
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2270
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This adds a helper function to read only a single GPIO which uses
3-state logic. Examples of this typically include board straps which
are used to provide mainboard-specific information at the hardware-
level, such as board revision or configuration options.
This is part of a larger clean-up effort for Snow. We may want to
genericise this for other CPUs in the future.
Change-Id: Ic44f5e589cda89b419a07eca246847e9ce7dcd8d
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2266
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This adds /src/include/gpio.h which currently contains generic GPIO
enums for type (in/out/alt) and 3-state logic.
The header was originally written for another FOSS project
(code.google.com/p/mosys) and thus the BSD license.
Change-Id: Id1dff69169e8b1ec372107737d356b0fa0d80498
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2265
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The cpu_is_exynos5() macro seems broken at the moment, so skip it.
The macro is superfluous and will probably be replaced eventually,
but at least this will un-break usage sites.
Change-Id: Ibd360cbfa18047ad8a3488d4f24c3fc4d7415eba
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2264
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
For ARM platform, the bootblock may need more C source files to initialize
UART / SPI for loading romstage. To preventing making complex and implicit
dependency by using #include inside bootblock.c, we should add a new build class
"bootblock".
Also #ifdef __BOOT_BLOCK__ can be used to detect if the source is being compiled
for boot block.
For x86, the bootblock is limited to fewer assembly files so it's not using this
class. (Some files shared by x86 and arm in top level or lib are also changed
but nothing should be changed in x86 build process.)
Change-Id: Ia81bccc366d2082397d133d9245f7ecb33b8bc8b
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2252
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
The LVDS is on DP0, not DP1.
Change-Id: I724764d0f013e7a10d974a8716e075139982ded2
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/2259
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Mike Loptien <mike.loptien@se-eng.com>
Eliminate the warning message:
ld: warning: cannot find entry symbol _start; defaulting to 040000000
The "_start" from c_start.S is deprecated so we need to define entry
point again in link description file.
Change-Id: I174428faa2e7f08cd91fe96a53e6efea9dc3634e
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2258
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
This removes a few lines which are obsolete or unneeded.
We may want to do something with SMP eventually (can we use it for
decompression?) but for now we'll assume non-bootstrap cores are idle
until the OS does something with them.
Change-Id: Iff6b196e008e803bcfd00e5de07cf471bd2357ea
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2257
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This is a first cut at a romstage. It sets up memory, although that
needs some work; and finds and loads a ramstage.
Change-Id: I02a0eb48828500bf83c3c57d4bacb396e58bf9a5
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2245
Tested-by: build bot (Jenkins)
Discovering memory timings is a bit complicated due to the need
to obtain and decode board config. To make things worse, the imported
code makes a mess of dependencies. Hard-code the memory timings
for now to get us further along (the instability won't really matter
until we're loading depthcharge anyway).
Change-Id: I1f341ad597db0c31ed4ae6bc703fc22b6596a803
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2256
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
LZMA decode library used to retrieve output size by:
outSize = *(UInt32 *)(src + LZMA_PROPERTIES_SIZE);
'src' is aligned but LZMA_PROPERTIES_SIZE may refer to an unaligned address like
src+5, and using that as integer pointer may fail on platforms like ARM. Also
this will fail on systems using big-endian (outSize was encoded in
little-endian).
To fix this, reconstruct outSize in little-endian way.
Change-Id: If678e735cb270c3e5e29f36f1fad318096bf7d59
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2246
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Continuing with the mainboard cleanup for F15tn, move the functions
to read the SPD from the mainboards for Thatcher and Parmer into the
wrapper for the northbridge/amd/agesa/family15tn.
Move the SPD address customization for the mainboard into the
devicetree.cb file.
Unrelated side note - Porting.h has an un-closed #pragma pack(1)
that can cause confusing side-effects. AGESA's structures all
use this, but coreboot's don't. Be sure to include the coreboot
.h files BEFORE Porting.h is included, not after.
This fix has been tested.
Change-Id: I89cdd225be61f60c6b8e7020e6f8b879983bbd96
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2190
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
This replaces the current stage-specific exit/entry functions with
generic versions. Now all stages compile with stage_entry(), which
is placed at .text.stage_entry.armv7, and stage_exit().
Snow's ramstage files are also updated to avoid build breakage.
Change-Id: I953a2c4b8121bd4b66c3362557997a9ca3aa53b0
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2254
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
The do_div code has a nice optimization in it when it is called with
constants. The current highly generalized use of it defeats those
optimizations and causes trouble on ARM, resulting in a complex and
buggy code path.
Since we only need to print in bases 8, 10, and 16, do a minor
restructuring of the code so that we call do_div with constants.
If you need base 2, print in base 16 and do it in your head. :-)
This fixes an ongoing problem with ARM, will not harm X86, and will
help PPC should we ever want to support it again.
Plus, I don't have to ever try to understand the div64 assembly and where
it's going wrong :-)
Change-Id: I6a480011916eb0834e05c5bb10909d83330fe797
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2235
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
People make mistakes. Hanging the box is not a good reason to kill the firmware,
esp. since this is probably happening in a printk.
The only issue with the recursive call to printk is that we may
deadlock if we have locked something. But we can at least try.
Hanging is certainly not what we want ...
Change-Id: Ib3bc87bc395ae89e115cf6d042f4167856422ca1
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2233
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
This is a minor set of changes to get DDR3 going.
Move compilation of DDR3 startup to the romstage. Fix a prototype that
was missing a void. Remove a function that is overly flexible, and
even though it is overly flexible only actually can handle one type of
RAM. Mainboards only support one type of DRAM, so create a function
to explicitly initialize the type of DDR we have -- DDR3.
With these changes, and the previous changes, google snow is ready to run
the ramstage.
Change-Id: I37e0ab0d2dbc1dd121fb175386a46bc2fb1285e5
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2224
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: David Hendricks <dhendrix@chromium.org>
The SPI flash driver for Exynos chipset.
Verified to boot on snow/armv7.
Change-Id: I7eef67a9c57f825d09f13ea44c2b59b54345fa7b
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2229
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Summary:
Isolate CBFS underlying I/O to board/arch-specific implementations as
"media stream", to allow loading and booting romstage on non-x86.
CBFS functions now all take a new "media source" parameter; use
CBFS_DEFAULT_MEDIA if you simply want to load from main firmware.
API Changes:
cbfs_find => cbfs_get_file.
cbfs_find_file => cbfs_get_file_content.
cbfs_get_file => cbfs_get_file_content with correct type.
CBFS used to work only on memory-mapped ROM (all x86). For platforms like ARM,
the ROM may come from USB, UART, or SPI -- any serial devices and not available
for memory mapping.
To support these devices (and allowing CBFS to read from multiple source
at the same time), CBFS operations are now virtual-ized into "cbfs_media". To
simplify porting existing code, every media source must support both "reading
into pre-allocated memory (read)" and "read and return an allocated buffer
(map)". For devices without native memory-mapped ROM, "cbfs_simple_buffer*"
provides simple memory mapping simulation.
Every CBFS function now takes a cbfs_media* as parameter. CBFS_DEFAULT_MEDIA
is defined for CBFS functions to automatically initialize a per-board default
media (CBFS will internally calls init_default_cbfs_media). Also revised CBFS
function names relying on memory mapped backend (ex, "cbfs_find" => actually
loads files). Now we only have two getters:
struct cbfs_file *entry = cbfs_get_file(media, name);
void *data = cbfs_get_file_content(CBFS_DEFAULT_MEDIA, name, type);
Test results:
- Verified to work on x86/qemu.
- Compiles on ARM, and follow up commit will provide working SPI driver.
Change-Id: Iac911ded25a6f2feffbf3101a81364625bb07746
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2182
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This is a port of the following
commit 8a49ac7f80
Rename fam14 pci northbridge ops functions.
Clarify the northbridge ops function names.
original-Change-Id: If7d89de761c1e22f9ae39d36f5cf334cc2910e1d
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Change-Id: Id7889bf02e2696220081251acdf695327267c796
Signed-off-by: Steven Sherk <steven.sherk@se-eng.com>
Reviewed-on: http://review.coreboot.org/2225
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
This is a port of the following
commit 8a49ac7f80
Rename fam14 pci northbridge ops functions.
Clarify the northbridge ops function names.
original-Change-Id: If7d89de761c1e22f9ae39d36f5cf334cc2910e1d
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Change-Id: Icda3ec58219baa177af3b1dce729c6ad1f744be8
Signed-off-by: Steven Sherk <steven.sherk@se-eng.com>
Reviewed-on: http://review.coreboot.org/2226
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
Update function messages to be more portable by using
the __func__ compiler command instead of hard coded
function names.
Change-Id: I6327c9769c2544bbc56155a2f89afd767487faf6
Signed-off-by: Mike Loptien <mike.loptien@se-eng.com>
Reviewed-on: http://review.coreboot.org/2227
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This is a Tiano Core loader payload based on libpayload. It
will load a Tiano Core DXE core from an UEFI firmware volume
stored in CBFS.
Currently Tiano Core dies because it does not find all the UEFI services it needs:
coreboot-4.0-3316-gc5c9ff8-dirty Mon Jan 28 15:37:12 PST 2013 starting...
[..]
Tiano Core Loader v1.0
Copyright (C) 2013 Google Inc. All rights reserved.
Memory Map (5 entries):
1. 0000000000000000 - 0000000000000fff [10]
2. 0000000000001000 - 000000000009ffff [01]
3. 00000000000c0000 - 0000000003ebffff [01]
4. 0000000003ec0000 - 0000000003ffffff [10]
5. 00000000ff800000 - 00000000ffffffff [02]
DXE code: 03e80000
DXE stack: 03e60000
HOB list: 03d5c000
Found UEFI firmware volume.
GUID: 8c8ce578-8a3d-4f1c-9935-896185c32dd3
length: 0x0000000000260000
Found DXE core at 0xffc14e0c
Section 0: .text size=000158a0 rva=00000240 in file=000158a0/00000240 flags=60000020
Section 1: .data size=00006820 rva=00015ae0 in file=00006820/00015ae0 flags=c0000040
Section 2: .reloc size=000010a0 rva=0001c300 in file=000010a0/0001c300 flags=42000040
Jumping to DXE core at 0x3e80000
InstallProtocolInterface: 5B1B31A1-9562-11D2-8E3F-00A0C969723B 3E96708
HOBLIST address in DXE = 0x3E56010
Memory Allocation 0x00000003 0x3E80000 - 0x3EBFFFF
FV Hob 0xFFC14D78 - 0xFFE74D77
InstallProtocolInterface: D8117CFE-94A6-11D4-9A3A-0090273FC14D 3E95EA0
InstallProtocolInterface: EE4E5898-3914-4259-9D6E-DC7BD79403CF 3E9630C
Security Arch Protocol not present!!
CPU Arch Protocol not present!!
Metronome Arch Protocol not present!!
Timer Arch Protocol not present!!
Bds Arch Protocol not present!!
Watchdog Timer Arch Protocol not present!!
Runtime Arch Protocol not present!!
Variable Arch Protocol not present!!
Variable Write Arch Protocol not present!!
Capsule Arch Protocol not present!!
Monotonic Counter Arch Protocol not present!!
Reset Arch Protocol not present!!
Real Time Clock Arch Protocol not present!!
ASSERT_EFI_ERROR (Status = Not Found)
ASSERT /home/reinauer/svn/Tiano/edk2/MdeModulePkg/Core/Dxe/DxeMain/DxeMain.c(461): !EFI_ERROR (Status)
Change-Id: I14068e9a28ff67ab1bf03105d56dab2e8be7b230
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2154
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
[…]
CC romstage.inc
src/mainboard/asrock/e350m1/romstage.c: In function 'cache_as_ram_main':
src/mainboard/asrock/e350m1/romstage.c:48:5: warning: unused variable 'reg8' [-Wunused-variable]
This change was already done for AMD Persimmon in the following
commit.
commit d7a696d0f2
Author: efdesign98 <efdesign98@gmail.com>
Date: Thu Sep 15 15:24:26 2011 -0600
Persimmon updates for AMD F14 rev C0
Change-Id: I8f1ae1a609b87b197583934f0556f66b64e6994d
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2230
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
At some point we did a lot of cleanup to replace bare 'unsigned'
with 'unsigned int'. Do that work for this imported code as well.
At some point, we may find we can shrink these 'int's to something
smaller, thought I very much doubt it's worth the trouble.
Change-Id: Ic3da491c0188c56c836f8b9c4c8f26a31b4b3573
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2223
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
It can be handy to have debug prints as DRAM is started up, so that
in the case of failure (does that ever happen?) you've got some
idea where it failed.
This patch adds some DEBUG_SPEW prints to the DDR3 code. I am doing this
as its own CL because we may find we want to revert it. That's unlikely
but it is not impossible if we skew the timing in some way.
This code works for some trivial DRAM tests.
Change-Id: I57e8d2a2d8df6b8ec8cd0d414681fc513e9999e3
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2222
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
The timing array is crucial to proper operation of DRAM.
Getting a valid pointer to it is hence very important. Unfortunately,
the constants chosen for the vendor were '1', and '2', (this in a
32-bit word) which in a debug print makes it almost impossible to tell
if you've got a misaligned pointer. Note: coreboot people did not
choose them :-)
So, give them values which are extremely unlikely to occur elsewhere
in the array (or in memory, for that matter).
Given the frequency with which this check occurs, i.e. once, I would
much prefer strings but I expect I'd get shouted down on that
one. Constants in this case are an almost useless optimization but
we'll go with them for now. Note no space is saved by not using
strings: there's an entire function somewhere devoted to mapping the
enum to a string!
Debug prints of pointers to structs in this array are now far more
useful than they were.
See snarky comment in the code (left there to make sure nobody gets
tempted to get fancy again). Comment now less snarky.
This is tested on google snow to the point that the DRAM works.
Change-Id: I30bc44719f321f791fd82ded60e29393399d9e3d
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2221
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Tested-by: build bot (Jenkins)
Currently "cbfstool locate" outputs a hex number without "0x" prefix.
This makes extra step (prefix 0x, and then generate another temp file) in build
process, and may be a problem when we want to allow changing its output format
(ex, using decimal). Adding the "0x" in cbfstool itself should be better.
Change-Id: I639bb8f192a756883c9c4b2d11af6bc166c7811d
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2201
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
The previous incarnation did not use all of mmu_setup, which meant
we did not carefully disable things before (possibly) changing them.
This code is tested and works, and it's a bit of a simplification.
Change-Id: I0560f9b8e25f31cd90e34304d6ec987fc5c87699
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2204
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: build bot (Jenkins)
This begins to remove references to global data which u-boot used.
There are still many commented out references to gd-> and bd-> which
we'll fix once we're happy with the replacements.
Change-Id: Ie1b40a997e28a118f8f3ad96a2f9a2462d32fbe3
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2210
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This just removes unused code. If for some reason we don't want to
initialize cache, then the CPU or mainboard specific init routines
don't need to call these.
Change-Id: Ieb7393b6cbc103e490753da4ed27114156466ded
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2209
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
This change is required in order to use a LVDS panel
attached to the LVDS connector.
Change-Id: Id97c233f964151b6515bd46c797425d0e6690cbd
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/2188
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
No need to keep duplicate variants of counting ioapic interrupts.
Change-Id: I512860297309c46e05cc5379bf61479878817b1e
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/2185
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
commit 585a400697
Author: zbao <fishbaozi@gmail.com>
Date: Thu Apr 12 11:27:26 2012 +0800
Leverage the Pstate table created by AGESA.
… introduced unneeded whitespace in front of a comma.
Revert that part of the above commit. In the file for AMD Dinar
tabs and spaces are mixed, but leave that alone for the beginning.
Change-Id: I279cd0cb0be8c79258034733773f2ae1c2207cce
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2187
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
`depends on FOO` in
if FOO
... depends on FOO
endif
is useless.
Introduced in
commit 4b508341bc
Author: efdesign98 <efdesign98@gmail.com>
Date: Wed Jul 13 17:16:13 2011 -0700
Add AMD Family 10 support to cpu folder
and probably copied later on in the following commit.
commit d3e990c6e5
Author: Kerry Sheh <shekairui@gmail.com>
Date: Tue Feb 7 20:31:35 2012 +0800
AGESA F15: AGESA family15 model 00-0fh cpu wrapper
Change-Id: I67cf231e3047a07cb6f0eeb5f77be368674a0603
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2186
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Hengelein <ilendir@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Apply the same fix for `setup_ioapic` as done in the following commit.
commit 23c046b6f1 Author: Nico Huber <nico.huber@secunet.com> Date: Mon Sep 24 10:48:43 2012 +0200
Fix reading of number of interrupts for IO-APICs
The number read from the io-apic register represents the index of the
highest interrupt redirection entry, i.e. the number of interrupts
minus one.
Change-Id: I54c992e4ff400de24bb9fef5d82251078f92c588
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1624
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Change-Id: I7b730d016a514c95c3b32aee6f31bd3d7b2c08cb
Signed-off-by: Aladyshev Konstantin <aladyshev@nicevt.ru>
Reviewed-on: http://review.coreboot.org/2043
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The coreboot resource allocator doesn't respect resources
claimed in the APIC_CLUSTER. Move the MMCONF resource to the
PCI_DOMAIN to prevent overlap with PCI devices.
Change-Id: I8541795f69bbdd9041b390103fb901d37e07eeb9
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/2167
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-by: Steve Goodrich <steve.goodrich@se-eng.com>
Clarify the northbridge ops function names.
Change-Id: If7d89de761c1e22f9ae39d36f5cf334cc2910e1d
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/2166
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Enable 'all warnings being treated as errors' in thatcher and parmer.
Fixed the following warnings on parmer / thatcher:
src/vendorcode/amd/agesa/f15tn/Proc/CPU/Feature/cpuFeatureLeveling.c:
In function 'GetGlobalCpuFeatureListAddress':
src/vendorcode/amd/agesa/f15tn/Proc/CPU/Feature/cpuFeatureLeveling.c:291:14:
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
src/vendorcode/amd/agesa/f15tn/Proc/CPU/S3.c:
In function 'SaveDeviceContext':
src/vendorcode/amd/agesa/f15tn/Proc/CPU/S3.c:245:18:
warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
src/vendorcode/amd/agesa/f15tn/Proc/CPU/S3.c:309:16:
warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
src/vendorcode/amd/agesa/f15tn/Proc/CPU/cpuPostInit.c:
In function 'GetPstateGatherDataAddressAtPost':
src/vendorcode/amd/agesa/f15tn/Proc/CPU/cpuPostInit.c:235:10:
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
src/vendorcode/amd/agesa/f15tn/Proc/Mem/NB/TN/mntn.c:
In function 'MemNInitNBDataTN':
src/vendorcode/amd/agesa/f15tn/Proc/Mem/NB/TN/mntn.c:353:32:
warning: assignment from incompatible pointer type [enabled by default]
src/vendorcode/amd/agesa/f15tn/Proc/Mem/NB/TN/mntn.c:363:23:
warning: assignment from incompatible pointer type [enabled by default]
src/vendorcode/amd/agesa/f15tn/Proc/CPU/Feature/cpuFeatureLeveling.c:
In function 'GetGlobalCpuFeatureListAddress':
src/vendorcode/amd/agesa/f15tn/Proc/CPU/Feature/cpuFeatureLeveling.c:291:14:
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
src/vendorcode/amd/agesa/f15tn/Proc/CPU/S3.c:
In function 'SaveDeviceContext':
src/vendorcode/amd/agesa/f15tn/Proc/CPU/S3.c:245:18:
warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
src/vendorcode/amd/agesa/f15tn/Proc/CPU/S3.c:309:16:
warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
In file included from src/northbridge/amd/agesa/family15tn/northbridge.c:37:0:
src/vendorcode/amd/agesa/f15tn/AGESA.h:1547:0:
warning: "TOP_MEM" redefined [enabled by default]
src/include/cpu/amd/mtrr.h:31:0:
note: this is the location of the previous definition
src/vendorcode/amd/agesa/f15tn/AGESA.h:1548:0:
warning: "TOP_MEM2" redefined [enabled by default]
src/include/cpu/amd/mtrr.h:34:0:
note: this is the location of the previous definition
In file included from src/northbridge/amd/agesa/family15tn/northbridge.c:41:0:
src/vendorcode/amd/agesa/f15tn/Proc/CPU/cpuRegisters.h:378:0:
warning: "LOCAL_APIC_ADDR" redefined [enabled by default]
src/include/cpu/x86/lapic_def.h:9:0: note:
this is the location of the previous definition
In file included from src/mainboard/amd/parmer/BiosCallOuts.h:24:0,
from src/mainboard/amd/parmer/mainboard.c:28:
src/vendorcode/amd/agesa/f15tn/AGESA.h:1547:0:
warning: "TOP_MEM" redefined [enabled by default]
src/include/cpu/amd/mtrr.h:31:0:
note: this is the location of the previous definition
src/vendorcode/amd/agesa/f15tn/AGESA.h:1548:0:
warning: "TOP_MEM2" redefined [enabled by default]
src/include/cpu/amd/mtrr.h:34:0: note:
this is the location of the previous definition
Change-Id: Iecea28232f1761401cf09f7d2a77d3fbac2f5801
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2171
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The "system is legacy free" question accidentally escaped
from the hudson Kconfig where it was intended to stay and
went coreboot-wide. This puts it back inside the boundries
of the hudson southbridge where it belongs.
I also commented the endif statements to make it easier to
tell where things belong.
Change-Id: I49f7a5eadb96d40c6101a93bc390e644617a5654
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2179
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This replaces the call() function with a stub which is compiled
separately using -marm. See http://review.coreboot.org/#/c/2175/
for details.
Change-Id: I7f8c45b5e63ec97b0a82294488129d1c97ec0cbf
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2180
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Go through southbridge/amd/agesa/hudson, thatcher and parmer
mainboard directories and change all references to sb800 to
reference hudson instead.
This is just cleanup and should make no functional difference.
Change-Id: Icd6a9a08c4bbf5e1aed394362d24c05811ed1fba
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2177
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
There are currently too many things in the mainboard directories that
are really more suited to being in the northbridge / southbridge
wrappers. This is a start at moving some of those functions down
into the wrappers.
Move the bios callback functions into the northbridge/amd/agesa/family15tn
directory from the mainboard directories. These can still be overridden
by any mainboard just by updating the pointer in the callback table to
point to a customized version of the function.
Change-Id: Icefaa014f4a4abbe51870aee7aa2fa1164e324c1
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2169
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
In the AGESA routine GfxInitSview() called in the S3save path,
the IO Space bit was getting cleared from the command register.
This kept seabios from initializing the video bios. If the vbios
was loaded by coreboot, this routine was skipped, allowing seabios
to initialize vbios as well. I have modified the routine to save
and restore the command register instead of clearing the IO Space
bit.
Change-Id: I756b0606adbc47da96780308c911852e39f547c7
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2172
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
Add Kconfig option for Legacy free and hook it into the parmer
AGESA initialization as well as the FADT code. This should really
be done inside the southbridge wrapper and not in the mainboard,
but for now the code to attach it to is inside the mainboard.
Update Kconfig for parmer and thatcher to default to legacy free.
Change-Id: Ib899bd02ddc5506caae4aca2c589cc2526638cb8
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2157
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
Update the southbridge/amd/agesa/hudson FADT generation for ACPI
3.0 compliance similar to what was done for cimx/SB800/fadt.c in
commit 9aa4389.
commit 9aa43892e6
Author: Martin Roth <martin@se-eng.com>
Date: Fri May 25 12:23:32 2012 -0600
Update SB800 CIMX FADT
According to the datasheet, PMA_CNT_BLK is no longer available
and PM2_CNT_BLK should not be used. Setup for these has been
removed from the table and .h file.
Change-Id: Ied8eb1f26b4aa364d051ec5f7ed6f482bb440957
Signed-off-by: Martin Roth <martin@se-eng.com>
Reviewed-on: http://review.coreboot.org/2140
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
The Number of Ports register says that it should be set to the maximum
number of ports supported by the silicon. AGESA was setting this to be
the number of enabled ports. If port 1 was the only port with a drive,
this value got set to 0, indicating 1 port. This causes SeaBIOS to only
look at port 0 and quit, never finding the drive on port 1.
Dave Frodin: I also verified that this patch allows a SATA drive plugged
into port 2 to be detected without a device in port 1.
Change-Id: I5d49e351864449520e3957bbb07edf0f3ec2fd47
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2165
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
Re-formatting and cleaning up the devicetree.cb files for
parmer and thatcher.
Change-Id: Ic458e59701c1f2593b0a035b96cac60df476ee82
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2164
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
The way that devicetree.cb was configured for the family 15tn boards
was doing... interesting things to the video device initialization.
This was causing S3 resume to fail.
There is a disconnect between how the devicetree should be configured
if there are multiple HT links on the CPU and how it's configured if
there's only one HT link. These platforms were set up as if they
had multiple HT links, which was causing duplicate instances of
devices in the device list.
The scan for the IO Hub was removed from the northbridge code which
isn't a problem for F15tn devices.
Change-Id: I3556b43027746e36b07de7cb1bece4d1b37a3c34
Signed-off-by: Martin Roth <martin@se-eng.com>
Reviewed-on: http://review.coreboot.org/2160
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
This patch does a few things to get us into romstage:
- Add romstage as a stage (a later patch adds it as a binary, which
is probably wrong). The Makefile magic is complex enough that we
let it build the XIP file for now, but we no longer use it.
- Replace findstage with loadstage. Loadstage will find a stage,
load the code to memory, and zero the remaining part of memory.
Now we can link the romstage to go anywhere!
- Eliminate magic offsets from code/ldscripts and centralize Kconfig
variables in src/cpu/samsung/exynos5250/Kconfig.
- Tidy up code and serial output
Change-Id: Iae4d2f9e7f429cb1df15d49daf9a08b88d75d79d
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2174
Tested-by: build bot (Jenkins)
.. to reflect the recent changes w.r.t avoiding
trouble with the coreboot pre-commit hooks.
and fix two whitespace errors.
Change-Id: I6c94e95dd439940cf3b44231c8aab5126e9d45c7
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2158
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
This adds a wrapper around main() in romstage which is compiled using
-marm. This assumes that the bootblock branches to romstage in ARM
mode.
The long-term idea is to enforce ABI compatibility when handing off to
the next stage by using shims which are which are compiled in a pre-
determiend manner and leave the main portions of each stage up to
whatever the compiler wants. So it will eventually look like this:
1. bootblock_main (ARM/Thumb)
2. bootblock_exit (ARM)
3. romstage_entry (ARM)
4. romstage_main (ARM/Thumb)
(credit to Gabe Black for writing the patch, I'm just uploading it)
Change-Id: I4fdb8d2c6c2c0a7178bcb9154c378ddce0567309
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Reviewed-on: http://review.coreboot.org/2175
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This is the bloated Snow bootblock which includes:
- SPI driver
- UART, including requisite I2C, Maxim PMIC, and clock config code.
- Adjustments for magic offsets (id section, stack pointer address)
This is just a temporary solution until we have romstage loading.
Once that happens, we'll rip out all but the code necessary for
copying SPI ROM content into SRAM.
Change-Id: I2a11e272eb9b6f626b5d9783eabb4a720a1d06be
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2170
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
We've had obscure errors as the size of the bootblock changes.
This fix allows us to use a 32-bit constant. Please test on
real hardware before you ack.
Change-Id: Ic3d9f4763554bd6104ae9c4ce5bbacd17b40872c
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2168
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Tested-by: build bot (Jenkins)
Our earlier attempt was jumping straight from asm to the old u-boot
board_init_f in lowlevel_init_c.c. We are getting ready to transition
to using a real bootblock for ARM, so add romstage.c to the files
compiled and we'll make main() our entry point.
This also updates romstage.ld to place main() (*(.text.startup)) at
the beginning of romstage.
Change-Id: Ifc77a6bfba27d915c4cad62c6c8040665294628a
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2163
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
We don't pass any arguments into romstage on ARM.
Change-Id: I018f28a57fc486c9240345cf0f4043b79027d864
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2162
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This adds a stub for bootblock_cpu_init() for exynos5250. It will
eventually contain code to copy ROM content from SPI to SRAM.
Change-Id: I26ee62a1e701013f38f76f200579faa680530860
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2138
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This replaces hard-coded bootblock offsets using the new scheme.
The assembler will place the initial branch instruction after BL1,
skip 2 aligned chunks, and place the remaining bootblock code after.
It will also leave an anchor string, currently 0xdeadbeef which
cbfstool will find. Once found, cbfstool will place the master CBFS
header at the next aligned offset.
Here is how it looks:
0x0000 |--------------|
| BL1 |
0x2000 |--------------|
| branch |
0x2000 + align |--------------|
| CBFS header |
0x2000 + align * 2 |--------------|
| bootblock |
|--------------|
TODO: The option for alignment passed into cbfstool has always been
64. Can we set it to 16 instead?
Change-Id: Icbe817cbd8a37f11990aaf060aab77d2dc113cb1
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2148
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This lays out the groundwork for using a proper bootblock on ARM.
Currently we bypass the bootblock entirely and go straight to
romstage. However we want to utilize CBFS to maximize flexibility
of placing code without relying on a lot of magic numbers which
will break depending on the SoC in use.
Change-Id: I9cc2a8191d2db38b27b6363ba673e5a360de9684
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2118
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Bits were being shifted off the end of the mask accidentally.
This results in all masks being 32 bits wide instead of 48.
Change-Id: I5f4d1b6a323df1aa4568ff4491f82447b8a2f839
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2146
Tested-by: build bot (Jenkins)
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
... and delete traces in source files.
Change-Id: Ie0f70a479f1eadadc654a41fa3c426d1d4ac2f2b
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2152
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Make the comments match what pre-commit-hook wants.
Change-Id: Ib99a6583f97221df3638bd3b7723f51d5f9c223c
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2143
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
In order to provide some insight on what code is executed during
coreboot's run time and how well our test scenarios work, this
adds code coverage support to coreboot's ram stage. This should
be easily adaptable for payloads, and maybe even romstage.
See http://gcc.gnu.org/onlinedocs/gcc/Gcov.html for
more information.
To instrument coreboot, select CONFIG_COVERAGE ("Code coverage
support") in Kconfig, and recompile coreboot. coreboot will then
store its code coverage information into CBMEM, if possible.
Then, run "cbmem -CV" as root on the target system running the
instrumented coreboot binary. This will create a whole bunch of
.gcda files that contain coverage information. Tar them up, copy
them to your build system machine, and untar them. Then you can
use your favorite coverage utility (gcov, lcov, ...) to visualize
code coverage.
For a sneak peak of what will expect you, please take a look
at http://www.coreboot.org/~stepan/coreboot-coverage/
Change-Id: Ib287d8309878a1f5c4be770c38b1bc0bb3aa6ec7
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2052
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-by: Martin Roth <martin@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Please, don't just add random directories for a single file because
it seems convenient. There already is a chromeos directory, that should
be used.
Change-Id: I625292cac4cbffe31ff3e3d952b11cd82e4b151e
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2137
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
During the ARM port, disabling serial console became broken.
This patch fixes it.
Change-Id: I40460596073918a08c19bb9c991cada341cca940
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2136
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Since coreboot is compiled into 32bit code, and userspace
might be 32 or 64bit, putting a pointer into the coreboot
table is not viable. Instead, use a uint64_t, which is always
big enough for a pointer, even if we decide to move to a 64bit
coreboot at some point.
Change-Id: Ic974cdcbc9b95126dd1e07125f3e9dce104545f5
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2135
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This is the first lowlevel init routine that gets called in romstage.
It's fugly and needs a lot of clean-up, but does the job for now.
Change-Id: Id54bf4f1c3753bcbed5f6b5eeb4b48bc3b41ce93
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2133
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This cannot be used until we get the BL1 mess sorted out.
Change-Id: I2490addb31256e27caa89ebb5b1501296e6903bd
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2132
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The high bits of mtrr mask are MBZ (Must be zero). Writing 1 to these
bits will cause exception. So be carefull when spread this change.
The supermicro/h8scm needs more work. Currently it is set as it was.
We need to check if the F10 and F15 have different value.
Change-Id: I2dd8bf07ecee2fe4d1721cec6b21623556e68947
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1661
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
This replaces 0x02023400 with an SoC-specific Kconfig variable.
Change-Id: I21482d54a1e1fa6c4437c030ddae2b0bb3331551
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2130
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This doesn't seem to be strictly required (so far), but makes sense.
Change-Id: I18416c427ff886507ae09c7fc1a018baf94af24a
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2131
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
We don't pass arguments when we jump out of assembly code.
Change-Id: Iccf3a6f713e260b08f9ff47e8b542b9e96369166
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2122
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This does some clean-up for the exynos5250 clock_init.c:
- No global data.
- Remove some unused #includes
- Hard-code the memory type for Elpida DRAM. This will need to be
fixed eventually (or the system will be unstable), but is good
enough for early bring-up and until we finish other re-factoring.
Change-Id: Icd2cf8ba35058cbd1131666db311dfb77ef1a160
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2127
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Turns out initializing power rails is necessary, even for getting
serial output.
Change-Id: I3042c1001ae43b1e793ee6cb90bb79b8db0f8fd1
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2126
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This contains some size optimizations for the Maxim MAX77686 driver:
- change max77686_para.vol_{min,div} from u32 to u16 (currently their
max value is 50000 so it should be fine)
- remove max77686_para.regnum which takes 4 bytes for each and is not
used
(Patch was originally written by Hung-Te Lin, I'm just uploading it)
Change-Id: I24044427c49467e99380d1f60ebc59e69c285b22
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2124
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
ACPI code:
The ACPI code is not currently being compiled in by default, but
assuming that it will be at some point, I'm fixing the loop that
waits for the IMC to respond after sending it a command. The
loop now exits after 500ms, similar to the function in agesa.
Agesa Code:
a 16 bit variable will always be less than 100000. Change to
be a 32 bit variable.
Change-Id: I9430ef900a22d056871b744f3b1511abdfea516e
Signed-off-by: Martin Roth <martin@se-eng.com>
Reviewed-on: http://review.coreboot.org/2119
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The cimx/sb800 IMC Firmware location Kconfig option has
a typo which would could set it to the wrong location.
Change-Id: I38016bebd1bfe6ad6d3f1c02cb1960712fbf4ab2
Signed-off-by: Martin Roth <martin@se-eng.com>
Reviewed-on: http://review.coreboot.org/2120
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This patch switches the Qemu target to use (pseudo) Cache As RAM
and enables some ACPI code. This allows to use the CBMEM console
and timestamp code with coreboot in Qemu. Right now, the ACPI code
is commented out because leaving it in breaks IDE.
Change-Id: Ie20f3ecc194004f354ae3437b9cf9175382cadf8
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2113
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
We moved to using __ASSEMBLER__ years ago since it is set by as.
Change-Id: I60103ba23ebe87be1d0bc63beed0ef5b05eed4f2
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2111
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
It's a bad Linux heritage.. We have no userland in firmware.
Change-Id: Ib19e5ba713078ca37514571213d19f418417b964
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2108
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
It makes no sense to have directories with one file.
Change-Id: I65ba93dda5e6a4bcc5a7cc049c1378ebf5d6abcd
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2105
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
This reverts commit ec8d35fe91
We are almost certain that this is not necessary.
Change-Id: I70e94f883be95655da00a0b127ed9ffd7c81c63b
Reviewed-on: http://review.coreboot.org/2104
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Tested-by: build bot (Jenkins)
Our reference toolchain uses -mabi=aapcs whereas we started
forcing -mabi=aapcs-linux. Drop this to prevent ABI incompatibility.
Also drop -fno-common since that's set in the top level Makefile.inc
already.
Change-Id: I4afdcf5da9a5d86c2f9e5de5c7d523ccd2f5f1e0
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2103
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
We accidently checked in some files from libgcc as well as
a Makefile from u-boot and a duplicate implementation of div0.
Drop all those files to reduce the confusion.
Change-Id: I8ff6eabbced6f663813f8cc55f19c81839d03477
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2102
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
There was a misuse of bool that would cause the dcache policy to not be
set up correctly, but instead present options "y" and "n" in the Kconfig
menu.
Also, TINY_BOOTBLOCK was removed a while ago, everything is
TINY_BOOTBLOCK now. Hence remove the option.
Change-Id: I5c28ac828955c69614c7bdaf106f79db51e68723
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2101
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Add function "clear_ioapic" before "setup_ioapic" for RD890 northbridge
like it is done for SB700 and SB800 chipsets ("amd/cimx/sb{7,8}00").
No functionality change is noticed.
Change-Id: I1fd87692d8bf35c166141c9b7a6a1e748c19a636
Signed-off-by: Aladyshev Konstantin <aladyshev@nicevt.ru>
Reviewed-on: http://review.coreboot.org/2045
Tested-by: build bot (Jenkins)
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
There are two CPUs on s8226 and each CPU has 8 cores.
CPU 0 takes lapic from 0x10 to 0x17 and CPU 1 takes from 0x20 to 0x27.
So the first core's lapic is 0x10 rather than 0x20.
Change-Id: I925114d44f2f4974eb62c3832d8c9139a2a06c96
Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com>
Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/2099
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The 'VERSION' in CBFS header file is confusing and may conflict when being used
in libpayload.
Change-Id: I24cce0cd73540e38d96f222df0a65414b16f6260
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2098
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
This just cleans out some unused headers and tidies up the early
serial code.
TODO: Clean-up or replace FDT code, make "base_port" easier to
configure.
A bit of cleanup based on earlier patches.
Change-Id: Ie77ee6d4935346e0053c09252055662f1a45d5f5
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2084
Tested-by: build bot (Jenkins)
This patch makes pre-RAM serial init more generic, particularly for
platforms which do not necessarily need cache-as-RAM in order to use
the serial console and do not have a standard 8250 serial port.
This adds a Kconfig variable to set romstage-* for very early serial
console init. The current method assumes that cache-as-RAM should
enable this, so to maintain compatibility selecting CACHE_AS_RAM will
also select EARLY_SERIAL_CONSOLE.
The UART code structure needs some rework, but the use of ROMCC,
romstage, and then ramstage makes things complex.
uart.h now includes all .h files for all uarts. All 2 of them.
This is actually a simplifying change.
Change-Id: I089e7af633c227baf3c06c685f005e9d0e4b38ce
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2086
Tested-by: build bot (Jenkins)
This updates $CFLAGS used for armv7. Most of them were just added
to be consistent with what u-boot does. The important ones here
are -march=armv7-a and -mthumb (to allow 16-bit Thumb instructions).
I removed the hard float support because it got errors and
coreboot should never use floats anyway. We're still having trouble
with enums but I want to see how far it gets with this patch.
Also, put the flags in a form that makes diffs easier to read. It's
almost impossible otherwise.
Finally, move some flags to the architecture Makefile, and
rely on the fact that some are set for all architectures.
Depends-On: I6f730d017391f9ec4401cdfd34931c869df10a9e
Change-Id: Ia8a1ae22959933e06f7b996d1832cea40819f1ff
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2075
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This mirrors the naming convention of handlers in
northbridge and southbridge.
Change-Id: I45d97c569991c955f0ae54ce909d8c267e9a5173
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/2058
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This replaces a somewhat useless calculation used earlier (which
always evaluated to 0) with an offset to specify the location
of the Coreboot bootblock.
Change-Id: Ib85aaccf138cebeb6bf8aedf82308861206dff48
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2094
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This patch does two things which will take effect in follow-up
patches:
1. Add an intermediate Makefile rule for dd'ing BL1 into the
coreboot.rom pre-image. This is modeled after a similar hack
for the bd82x6x southbridge.
2. Add a Kconfig variable, BOOTBLOCK_OFFSET, which will be used to
pass the bootblock offset into cbfstool.
Change-Id: I89da255dc903c387b754b06a11bb3439035ead87
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2093
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
These are needed for communicating with the PMIC on Snow. We'll
tidy them up as we go along...
Change-Id: I197f59927eae0ad66191862d052de2a8873fb22f
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2078
Tested-by: build bot (Jenkins)
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
This imports SPL (second phase loader) files from U-Boot. Most of the
content of these files will eventually go away since they're fairly
U-Boot specific. For now they are here to make Jenkins happy.
Change-Id: Ib3a365ecb9dc304b20f7c1c06665aad2c0c53e69
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2081
Tested-by: build bot (Jenkins)
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
The old start.S file did a lot of work and had AP-specific #ifndef's.
The new init.S will eventually contain only bare minimum generic ARM
code for use by the bootblock. Processor-specific stuff and things
that take place later in the boot process should go elsewhere.
Change-Id: I7db0a77ee4bbad1ddecb193ea125d8941a50532b
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2083
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
'nough said. It was broken since 2006.
Change-Id: I312ac07eee65d6bb8567851dd38064c7f51b3bd2
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2062
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Success return value in DMI functions GetDmiInfoMain(..) and GetType4Type7Info(...) of AGESA vendorcode is "Flag = TRUE".
This results in a failure of init late function:
"agesawrapper_amdinitlate failed: 1"
It happens because TRUE = 1 = AGESA_UNSUPPORTED.
Replacing TRUE with AGESA_SUCCESS (= 0) fixes this problem.
Only family f15tn does not have such bug.
This patch just replaces TRUE with AGESA_SUCCESS, but maybe all DMI functions should be copied from Trinity family?
Tested on Supermicro H8QGI board with 4 AMD Opteron 6234 processors (f15).
Change-Id: I51bf91333c088a825b92d4a44d1ebe4380c8026c
Signed-off-by: Aladyshev Konstantin <aladyshev@nicevt.ru>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2070
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
I have issues when AmdReadEventLog function tries to use BiosCallouts interface.
So it is necessary to provide callout pointer to this function.
Change-Id: I4080e5f07d5d28c41688b2a7deff944b7a0f7bf7
Signed-off-by: Aladyshev Konstantin <aladyshev@nicevt.ru>
Reviewed-on: http://review.coreboot.org/2064
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
That code will be used to disable the internal GFX card and enable the
external PCIe card.
The following lines from function `rs780_internal_gfx_enable()` are
taken and reversed.
/* Disable external GFX and enable internal GFX. */
l_dword = pci_read_config32(nb_dev, 0x8c);
l_dword &= ~(1<<0);
l_dword |= 1<<1;
pci_write_config32(nb_dev, 0x8c, l_dword);
It has been tested on the M4A785T-M with the following card inside the
PCIe 16x slot:
02:00.0 VGA compatible controller: nVidia Corporation GT218 [GeForce 210] (rev a2)
Change-Id: I7bd412b987fde98c97464175e2c7a384a8f0fb84
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2065
Tested-by: build bot (Jenkins)
This commit enables the external graphics card.
In order to work, the internal graphic card has to be
disabled, that is done in src/device/device.c through:
vga_onboard->ops->disable(vga_onboard);
which calls the RS780 disable operation introduced in the following
commit: "rs780: add .disable pcie_ops"
This commit was tested with and without the following card:
02:00.0 VGA compatible controller: nVidia Corporation GT218 [GeForce 210] (rev a2)
Thanks Aladyshev for the pointer(in the #coreboot IRC channel on Freenode servers):
Dec 20 19:43:32 <Aladyshev> If you list your internal card in devicetree.cb,
coreboot will distinguish external and internal VGA and choose external one
Change-Id: I92e59dffd158db096a6e99d1ef6e2e248fef933c
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Reviewed-on: http://review.coreboot.org/2067
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
If a 3rd party blob option is selected, make sure that it makes the
user select CONFIG_USE_BLOBS as otherwise the build will fail.
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Change-Id: I04429f23137946525c8577dd9c979bd4a0d17cdc
Reviewed-on: http://review.coreboot.org/2080
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This just imports a header. We may wish to modify the i2c interface
and/or unify it with the smbus interface we currently have.
Change-Id: I314f3aef62be936456c6c3e164a3db2c473b8792
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2079
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Fix some minor discrepancies which prevented the MAX77676 from
getting compiled in properly.
Change-Id: Ib29136da6c15a4bdb24926a91729431c507cd209
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2076
Tested-by: build bot (Jenkins)
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Since these don't seem very generic and depend on the BL1, let's
move them to the CPU-specific Kconfig.
Change-Id: I33059b7db30d35a1853918a580f312e50a3499fa
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2077
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This is still a work-in-progress, but it seems to work better than
before and is less complicated...
Change-Id: I6f730d017391f9ec4401cdfd34931c869df10a9e
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2041
Tested-by: build bot (Jenkins)
Supermicro H8QGI has integrated Matrox G200 16MB DDR2 graphics.
List it in devicetree.cb to mark it as onboard VGA to coreboot.
This change makes menuconfig option "Use onboard VGA as primary video device" work.
Change-Id: Ia6b9f60e3ae705689f22babd544ad6e628a85df1
Signed-off-by: Aladyshev Konstantin <aladyshev@nicevt.ru>
Reviewed-on: http://review.coreboot.org/2042
Tested-by: build bot (Jenkins)
Reviewed-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
Fix little mistake in get_bus_conf code
Change-Id: I8c09e501082caa0a20266b007c0744630a356de0
Signed-off-by: Aladyshev Konstantin <aladyshev@nicevt.ru>
Reviewed-on: http://review.coreboot.org/2046
Tested-by: build bot (Jenkins)
Reviewed-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
Size of BiosCallouts[] struct can be calculated as:
CallOutCount = sizeof (BiosCallouts) / sizeof (BiosCallouts [0]);
There is no longer need for REQUIRED_CALLOUTS define.
Originally that change was done for AMD Persimmon in
commit d7a696d0f2
Author: efdesign98 <efdesign98@gmail.com>
Date: Thu Sep 15 15:24:26 2011 -0600
Persimmon updates for AMD F14 rev C0
without deleting the define. This was ported to some of the other
boards and for some the define was not removed.
The AMD Inagua, Parmer and Thatcher boards were already adapted but
the define was left in. So just remove it for those.
Tested on Supermicro H8QGI.
Change-Id: Ia09795579a1170fa20ab94a30feb1af6821153d2
Signed-off-by: Aladyshev Konstantin <aladyshev@nicevt.ru>
Reviewed-on: http://review.coreboot.org/2049
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin@se-eng.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
Since SB800, USB2.0 debug port is dev 0x12, func 2.
Change-Id: Ie0e33cb2f0833b0baeef81323e1a0634242fbe55
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1880
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
H8QGI board has 2 IO-APICS with 56 IRQ’s:
IOAPIC[0]: GSI 0-23 - SB700 southbridge
IOAPIC[1]: GSI 24-55 - RD890 northbridge
`gDefaultApicDeviceInfoTable[]` structure in northbridge code
vendorcode/amd/cimx/rd890/nbIoApic.c
has IO-APIC interrupt mapping for HT and IOMMU set to last 31
IRQ pin (24+31=55).
CONST APIC_DEVICE_INFO gDefaultApicDeviceInfoTable[] = {
// Group Swizzling Port Int Pin
{0, 0, 31}, //HT
{0, 0, 31}, //IOMMU
[…]
Also the same value (55) can be found in original Supermicro BIOS ACPI DSDT.
Change-Id: Ie26da1f773716d1b7f5f5f884050ae799afc0b7e
Signed-off-by: Aladyshev Konstantin <aladyshev@nicevt.ru>
Reviewed-on: http://review.coreboot.org/2047
Tested-by: build bot (Jenkins)
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
GNU CC coverage needs free() and it's highly desirable to leave
the code as genuine as possible.
Change-Id: I4c821b9d211ef7a8e7168dc5e3116730693999c6
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2051
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
We ship it in the 3rdparty repository.
Change-Id: Ida52bc7e813f8468910c4ea7838ebb863c52b88a
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/2060
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
While "payload none" is undesirable for instant flashing,
assume that it was a conscious user choice.
(more immediate: jenkins isn't happy with escape sequences)
Change-Id: I9958b34a037b4d10bb7dba893335a63917623a70
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/2055
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Initialize the pointer fadt to NULL to prevent a later comparison
(if (fadt == NULL)) when the pointer had the *possibility* of never
having been initialized.
Change-Id: Ib2a544c190b609ab8c23147dc69dca5f4ac7f38c
Signed-off-by: Martin Roth <martin@se-eng.com>
Reviewed-on: http://review.coreboot.org/2037
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: build bot (Jenkins)
Add prefix coreboot_ to let make clean find it and delete it.
Change-Id: Ieba9c0e7ca3d2afec311d64159b22746ba5825c4
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/2029
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Add configuration for AMD's IMC ROM and fan registers for cimx/sb800
platforms.
- Allows user to add the IMC rom to the build and to configure the
location of the "signature" between the allowed positions.
- Allows for no fan control, manual setup of SB800 Fan registers, or
setup of the IMC fan configuration registers.
- Register configuration is done through devicetree.cb. No files need
to be added for new platform configuration.
- Initial setup is for Persimmon, but may be extended to any cimx/sb800
platform.
Change-Id: Ib06408d794988cbb29eed6adbeeadea8b2629bae
Signed-off-by: Martin Roth <martin@se-eng.com>
Reviewed-on: http://review.coreboot.org/1977
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Marc Jones <marcj303@gmail.com>
The file generated when the IMC or XHCI binaries are included in the rom
was named $(obj)/hudson_romsig.bin. The problem with this is that it
doesn't get deleted when the user does a make clean.
changing the name to coreboot_hudson_romsig.bin makes this happen.
Change-Id: I19a40042fbf0f7b5633d7b35339c05ed90d3243b
Signed-off-by: Martin Roth <martin@se-eng.com>
Reviewed-on: http://review.coreboot.org/1978
Tested-by: build bot (Jenkins)
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
There was already a special case for the SPI base address in
lpc_set_resources for southbridge/amd/cimx/sb800 and
southbridge/amd/agesa/hudson, but it needed to be modified
to keep from killing the IMC rom during initialization. As
soon as the BAR is disabled by setting the new base address,
the IMC dies. The fix is to make sure it's still enabled
when setting the new base address instead of setting the new
address then re-enabling it.
Change the name SPIROM_BASE_ADDRESS to SPIROM_BASE_ADDRESS_REGISTER
to more accurately describe what we're using.
Change-Id: I216d75b722c4332c239d487111a9880eabf59e91
Signed-off-by: Martin Roth <martin@se-eng.com>
Reviewed-on: http://review.coreboot.org/1975
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
The SB800 and Hudson now support adding the IMC ROM which runs from the same
chip as coreboot. When the IMC is running, write or erase commands sent to
the spi bus will fail, and the IMC will die. To fix this, we send a request
to the IMC to stop fetching from the SPI rom while we write to it. This
process (in one form or another) is required for writes to the SPI bus while
the IMC is running.
Because the IMC can take up to 500ms to respond every time we claim the
bus, this patch tries to keep the number of times we need to do that to a
minimum. We only need to claim the bus on writes, and using a counter for
the semaphore allows us to call in once to claim the bus at the beginning
of a number of transactions and it will stay claimed until we release it
at the end of the transactions.
Claim() - takes up to 500ms hit
claim() - no delay
erase()
release()
claim() - no delay
write()
release()
Release()
Change-Id: I4e003c5122a2ed47abce57ab8b92dee6aa4713ed
Signed-off-by: Martin Roth <martin@se-eng.com>
Reviewed-on: http://review.coreboot.org/1976
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
cbfstool was called with the wrong parameters
Change-Id: I405d0fd7c84b46da3c98a36fd19ef0034dc175cf
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2022
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
With driver-y going away, the current driver code didn't get
compiled in with upstream.
Change-Id: I9bff45a35c995888a482bdc22a1573f6bfb88211
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2027
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This is the minimal set of sources that allow the board to build.
These need to be filled in with actual code. But if we get these in upstream
we can stop working against a WIP patch.
Change-Id: I9347a573bb40761f6a12be3ee8febe3ca4be55a3
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2018
Tested-by: build bot (Jenkins)
and disable IO mapped UARTs on ARMV7 per default
Change-Id: I712c4677cbc8519323970556718f9bb6327d83c8
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2021
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
... to fit into the naming convention
Change-Id: I4a7d81c4d6674d001fc831df863bd2343f6c636f
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2020
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
When we need i2c for this cpu we will use the coreboot
smbus code.
Change-Id: I4ba4cc9ae10e5ca830d621ee9c8d9f7bd2129e2f
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2019
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The max include file is in src/drivers/power.
Change-Id: I2e663b472cade17fc50edbb449c0e54fd4a991eb
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2017
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
This file builds fine without including arch/types.h
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Change-Id: Icd38cf429576a2a1a33ebca84389526feddfc169
Reviewed-on: http://review.coreboot.org/2015
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
stddef.h should be fairly generic across all platforms we'd want to
support, so let's move it to generic code.
Change-Id: I580c9c9b54f62fadd9ea97115933e16ea0b13ada
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2007
Tested-by: build bot (Jenkins)
The first ARMv7 CPU we're going to support is the Exynos 5250
used in the Google Snow ChromeBook.
Change-Id: I4de8433bbc6202eb8fef2556a11186a3376d411b
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2004
Tested-by: build bot (Jenkins)
Samsung SoC files, including Exynos5 (a Cortex-A15
implementation). Since this is an SoC we'll forego the x86-style
{north,south}bridge and cpu distinction. We may try to split some
stuff out before the final version if prudent.
Change-Id: Ie068e9dc3dd836c83d90e282b10d5202e7a4ba9b
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2005
Tested-by: build bot (Jenkins)
Fix debug printks which were not using CONFIG_DEBUG_SPI_FLASH,
which would cause long delays durring boot when SPI devices
were written.
Change-Id: I99fc3d5f847fdf4bb98e2a0342ea418ab7d5fc54
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/1965
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Mostly preventing inb/outb being used on non-x86
Change-Id: I0434df4ce477c262337672867dc6ce398ff95279
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2002
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
ARM does not need them, and they're causing trouble
Change-Id: I6c70a52c68fdcdbf211217d30c96e1c2877c7f90
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2009
Tested-by: build bot (Jenkins)
... on all other systems it will fail terribly ;-)
Change-Id: I7f8d10b71b2dbc798b28aee7c36872685c793fd8
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2001
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Because they use outb instructions, they are bound to fail
on non-PC80 systems like ARM.
Change-Id: I679ac6c0964c06c369cc90556529bb6f629d56f9
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1974
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Tested-by: build bot (Jenkins)
Instead of adding regparm(0) to each assembler function called
by coreboot, add an asmlinkage macro (like the Linux kernel does)
that can be different per architecture (and that is empty on ARM
right now)
Change-Id: I7ad10c463f6c552f1201f77ae24ed354ac48e2d9
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1973
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The ARM architecture is really many architectures, and most
of them need their own toolchain. After discussing with Ron
and David, we decided that we're going to call the architecture
of our ARM board armv7.. This patch cleans out the remainders
of ARCH_ARM in the tree and moves on to consistent ARMv7 naming.
As of now, we only support little endian ARMv7 CPUs. We can
fix that for big endian if/when it comes our way.
Change-Id: Id70c7ef615f600e4d09961d811e7ac974fce4811
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1968
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
get_option() is used to get a config option (debug loglevel) from
CMOS. However, not all machines have CMOS, so define a dummy inline
function that will return an error code so the caller (console_init())
will use the default loglevel.
Change-Id: I6adf371d79164178f40a83f7608289a6a7673357
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/1962
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
These are from u-boot but have been cleaned up somewhat to remove
references to linux include files.
Change-Id: I5fe3954a11d8c4aa792620ef5e1a5ee8932b8578
Signed-off-by: Hung-Ti Lin <hungte@chromium.org>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/1930
Tested-by: build bot (Jenkins)
to match src/include/device
Change-Id: I5d0e5b4361c34881a3b81347aac48738cb5b9af0
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1960
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
It only has two files, move them to src/lib
Change-Id: I17943db4c455aa3a934db1cf56e56e89c009679f
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1959
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
Set_boot_successful depends on CMOS parts that non-PC80
platforms do not have. For now, make the current path
depend on CONFIG_PC80_SYSTEM, and make the alternative
empty.
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Change-Id: I68cf63367c8054d09a7a22303e7c04fb35ad0153
Reviewed-on: http://review.coreboot.org/1954
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
It's a more easily maintainable format than a 128 byte binary blob
Change-Id: Ic9b9f53cd025b5f89a21971930fabf6592f95d67
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1867
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Supermicro h8scm has a C32 CPU socket, the details of this board is:
http://www.supermicro.com/Aplus/motherboard/Opteron4100/SR56x0/H8SCM-F.cfm
We are planning to replace legacy C32 code with agesa and the h8scm_fam10 do not support
family 15 CPU, so we update this mainboard with this patch.
This code supports memory at 800M Hz of f10 CPU, bu f15 CPU does not has this limitation.
If you want to change the frequency of memory, please edit the macros
"BLDCFG_MEMORY_BUS_FREQUENCY_LIMIT" and "BLDCFG_MEMORY_CLOCK_SELECT"
in src/mainboard/supermicro/h8scm/buildOpts.c
Change-Id: I9ca9e70d7f3e82c07e7d36695bf31008db152afb
Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com>
Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/1510
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
Change-Id: I4b735fe4e6441f99236e43b34695fdac95b8888a
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/1875
Tested-by: build bot (Jenkins)
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
Remove the old, unflexible code for storing S3 data in SPI flash.
Refer to flashrom. Tested on Parmer.
Change-Id: I60a10476befb4afab2b4241f01a988f4a8bb22cd
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1920
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Marc Jones <marcj303@gmail.com>
Not all architectures have PCI. This new config variable allows control
of whether PCI support is configued in. It is selected for ARCH_X86.
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Change-Id: Ic5fe777b14fd6a16ba605ada1e22acf3e8a2c783
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/1947
Tested-by: build bot (Jenkins)
Change allows to override default bootblock_mainboard_init() with
mainboard-specific code.
If the default bootblock_mainboard_init() handler is replaced, with
one from file BOOTBLOCK_MAINBOARD_INIT, one needs to take care the
replacement calls all the necessary bootblock_x_init() functions.
Change-Id: Ie8c667cdba7cafe9ed2d4b19ab2bd21d941ad4ca
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1845
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Makes it a bit easier to implement mainboard-specific behaviour
while executing the bootblock.
Change-Id: I04e87f89efb4fad1c0e20b62ea6a50329a286205
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1844
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This is an initial re-factoring of CBFS code to enable multiple
architectures. To achieve a clean solution, an additional field
describing the architecture has to be added to the master header.
Hence we also increase the version number in the master header.
Change-Id: Icda681673221f8c27efbc46f16c2c5682b16a265
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/1944
Tested-by: build bot (Jenkins)
Not sure why this never triggered an error before.
Change-Id: I85d8b3b862492df04163a5f751c7ea4288406860
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1946
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
This adds a dummy config for ARMV7 for developing various
follow-up patches which rely on ARCH_ARMV7.
Change-Id: Id913054d916f41607d10ebc02aaf74082e14b554
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/1939
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
Create a new directory in drivers for power controllers.
Add the MAXIM MAX77686 power control support.
Accessing this controller requires I2C support.
Note that this will not build until the I2C usage is changed for
coreboot. I'm putting it in mainly because we need it soon
and I want to see if the new directory is acceptable.
Change-Id: I6c2a6d2165f33b41d2c8e4813222b21d2385e879
Signed-off-by: David Hendricks <dhendrix@chromium.org>
SIgned-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/1938
Tested-by: build bot (Jenkins)
This provides weak empty declaration for mainboard_ops.
The struct chip_operations is not defined for __PRE_RAM__ so
the declaration is also moved upwards in the output.
Change-Id: I101f0b8b9f0a55fb51a7c6475d53cc588c84026d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1931
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
With these changes we have a mostly compiling target.
I'm still removing and pruning .h files, but hopefully later today I'll do
the last few .h commits and move on to .c
Change-Id: Ia82d787496184e028f37d7b67336d61fda75aa94
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/1937
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
As we move to supporting other systems we need to get rid of assembly
where we can. The log2 function in src/lib is identical to the assembly
one (tested for all 32-bit signed integers :-) and takes about 10 ns
to run as opposed to 5ns for the non-portable assembly version. While speed
is good, I think we can spare the 15 ns or so we add to boot time
by using the C version only.
Change-Id: Icafa565eae282c85fa5fc01b3bd1f110cd9aaa91
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/1928
Tested-by: build bot (Jenkins)
Change-Id: I48497adc29a1b8ca11d1e0a5d879cab5b6b55dcd
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/1926
Tested-by: build bot (Jenkins)
Per a conversation with Stefan, these chip-dependent files are moved
to the src tree, in the manner of other chips (north and southbridge).
Change-Id: I12645ba05eb241eda200ed06cb633541a6a98119
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Reviewed-on: http://review.coreboot.org/1925
Tested-by: build bot (Jenkins)
This gets rid of the somewhat unstructured placement of AMD's
sysinfo structure in CAR.
We used to carve out some CAR space using a Kconfig variable,
and then put sysinfo there manually (by "virtue" of pointer magic).
Now it's a variable with the CAR_GLOBAL qualifier, and build
system magic.
For this, the following steps were done (but must happen together
since the intermediates won't build):
- Add new CAR_GLOBAL sysinfo_car
- point all sysinfo pointers to sysinfo_car instead of GLOBAL_VAR
- remove DCACHE_RAM_GLOBAL_VAR_SIZE
- from CAR setup (no need to reserve the space)
- commented out code (that was commented out for years)
- only copy sizeof(sysinfo) into RAM after ram init, where
before it copied the whole GLOBAL_VAR area.
- from Kconfig
Change-Id: I3cbcccd883ca6751326c8e32afde2eb0c91229ed
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/1887
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Marc Jones <marcj303@gmail.com>
This broke because those components were not yet
committed when the patch to drop the driver class
was made.
Change-Id: I29948223503a6c4b196eafa169c064cd26da1be1
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1934
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
- Optionally override FSB clock detection in generic
LAPIC code with constant value.
- Override on AMD Model fxx, 10xxx, agesa CPUs with 200MHz
- compile LAPIC code for romstage, too
- Remove #include ".../apic_timer.c" in AMD based mainboards
- Remove custom udelay implementation from intel northbridges' romstages
Future work:
- remove the compile time special case
(requires some cpuid based switching)
- drop northbridge udelay implementations (i945, i5000) if
not required anymore (eg. can SMM use the LAPIC timer?)
Change-Id: I25bacaa2163f5e96ab7f3eaf1994ab6899eff054
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1618
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
When dropping ramstage.a, unused functions with unresolved
symbols are not silently dropped anymore. This makes the
tim5690 compilation fail.
This fix makes sure we don't compile in the int15 handler code
when we don't set CONFIG_VGA_ROM_RUN
Change-Id: If6872c983d9fd811eb33259421f94b551f3b9b34
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1929
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
Change-Id: Ib4401897570f9e4d31c18d05144b5deb6f4523bc
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/1873
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Marc Jones <marcj303@gmail.com>
When dropping ramstage.a duplicate symbols in ramstage
will start breaking the build. Hence drop all the duplicate
functions implemented by mainboards that have those functions
in generic or component code already.
Change-Id: I5cf8245c67b6f0f348388db54256d28f47017a61
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1865
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
c_start.o has a special case in the build system, which we can
eliminate, somewhat simplifying the build.
To ensure that the entry point is at the beginning, introduce a
new section .textfirst that is placed appropriately. In principle
the ENTRY() definition in the linker script should be enough, but
better be safe.
Change-Id: I9737f7f5731e12ceb2119eb432b0e09832bc53fa
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/1909
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The use of ramstage.a required the build system to handle some
object files in a special way, which were put in the drivers
class.
These object files didn't provide any symbols that were used
directly (but only via linker magic), and so the linker never
considered them for inclusion.
With ramstage.a gone, we can drop this special class, too.
Change-Id: I6f1369e08d7d12266b506a5597c3a139c5c41a55
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1872
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
ramstage.a has two issues:
1. duplicate source filenames don't survive the ar(1)
treatment properly (so files aren't considered)
2. ld doesn't resolve symbols if it isn't forced to, in
particular no overrides of weak symbols
Downside: The resulting binaries get slightly larger.
Link time optimizations should fix that, as would tighter
rules in the build system (to not compile unused code in
the first place).
Change-Id: Iaae771ec8f92b42069237acd3b79c14e5bf9c03d
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/1566
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
sconfig creates empty defaults for all chip_ops, which can be overridden
by drivers simply by providing a concrete implementation.
Change-Id: Ib37515f0b0747bdbf4da780d28690a1e719944b2
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/1567
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The calculation of COMB's irq reading was wrong by the 4-bit shift.
Also, the asl compiler warned about the splitting in lo/hi bytes which
seems unnecessary.
Change-Id: Ia5101d5a19f68c2da827d7e37a18922f959604c7
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1923
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Forgot to update the rk9 for the unified VGABIOS handling.
This applies to rk9 what is done for other boards in commits
3c84261e84d5d340695b
Change-Id: I892b7d81927e277778c1c5251d27416fa79c9868
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1924
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
For SST chips, the Write-Status-Register instruction must be
executed immediately after the execution of the
Enable-Write-Status-Register instruction, instead of Write-Enable.
Change-Id: I4b3473cd671829def3bd1641ececcf8d9dad4a56
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1919
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Roda RK9 is a notebook based on the GM45/ICH9 platform using DDR3 memory.
http://roda-computer.com/products/notebooks/rk9/
Tested with various Linux versions, known to work:
- 2x4GB RAM
- IGD
- HD Audio
- UHCI, EHCI
- AHCI
- NIC
- PCI
- PS/2 keyboard
- serial console
- ACPI lid switch
- ACPI battery/AC events
- power off, reboot
Change-Id: I7299dccbff2eea3544363fdd4f49f05aa3dae7bc
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1691
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Add support for ICH9 southbridge
Change-Id: I70612431101bf48d9dcc96ee1b37d257c9ad2ee2
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1690
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The code supports DDR3 boards only. RAM init for DDR2 is sufficiently
different that it requires separate code, and we have no boards to
test that.
Change-Id: I9076546faf8a2033c89eb95f5eec524439ab9fe1
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1689
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Add an init() function to the chip_operations which will be called
before bus enumeration. This allows to disable unused devices before
they get enumerated.
Change-Id: I63dd9cbfc7b5995ccafb7bf7a81dc71fc67906a0
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1623
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This will omit the mc1468181rtc header if it is not needed. Currently
it contains a lot of inlined functions which depend on architecture-
specific IO.
Change-Id: I4ef1bc1362c159e0c780c3eade01af04f029f949
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/1916
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
This adds more configurability to POST codes. The current assumption
is that POST codes should be written to an IO port (e.g. LPC) if POST
codes are enabled. This changes the assumption so that POST codes can
be written to the serial console without being written to an IO port.
This enables POST codes by default using "default y" to avoid
changing current behavior.
Change-Id: I3db91c358ccb1557096983c4d07f70b2e872c4b3
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/1685
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Some boards have two instances of the int15 handler that supports
the onboard VGA BIOS, for YABEL and realmode.
These are now similar enough that they can be deduplicated.
Due to minor differences this requires manual effort.
Change-Id: I03ae314cb90dd65d96591ce448504aa961cbeb88
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1893
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Makes it more similar to what realmode looks like.
Change-Id: I4407431f2d979c43dd186114d67ed11845907afe
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1892
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
By using the (global) register file as defined by x86emu,
we can use the same register access for YABEL and realmode
interrupt handlers.
- the x86 realmode interrupt handlers changed in signature
- to access registers, use X86_$REGNAME now (eg. X86_EAX)
- x86_exception_handler still uses struct eregs *regs to
avoid spilling the x86emu register file stuff everywhere
Coccinelle script that handled most of this commit:
@ inthandler @
identifier FUNC, regs;
@@
int FUNC(
-struct eregs *regs
+void
)
{ ... }
@ depends on inthandler @
identifier regs;
@@
-regs->eax
+X86_EAX
@ depends on inthandler @
identifier regs;
@@
-regs->ebx
+X86_EBX
@ depends on inthandler @
identifier regs;
@@
-regs->ecx
+X86_ECX
@ depends on inthandler @
identifier regs;
@@
-regs->edx
+X86_EDX
@ depends on inthandler @
identifier regs;
@@
-regs->esi
+X86_ESI
@ depends on inthandler @
identifier regs;
@@
-regs->edi
+X86_EDI
@ depends on inthandler @
identifier regs;
@@
-regs->eflags
+X86_EFLAGS
@ depends on inthandler @
identifier regs;
@@
-regs->vector
+M.x86.intno
Change-Id: I60cc2c36646fe4b7f97457b1e297e3df086daa36
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1891
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
realmode int handlers must return the same codes as the YABEL
int handlers now: 1 for "interrupt handled", 0 for "not handled"
(ie. error).
Change-Id: Idc01cf64e2c97150fc4643671a0bc4cca2ae6668
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1890
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
It's really a feature in parallel to YABEL/x86emu. Reflect this in
the directory structure.
Change-Id: Ie88e4fa6bfef13d23c55b2db3faacbd90f8cc30b
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1889
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Change-Id: I4128af7912bec090bbd48acc1b20d0452e7a4a28
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/1876
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
e.g.
-#if CONFIG_LOGICAL_CPUS == 1
+#if CONFIG_LOGICAL_CPUS
This will make it easier to switch over to use the config_enabled()
macro later on.
Change-Id: I0bcf223669318a7b1105534087c7675a74c1dd8a
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1874
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This unused code was not silently dropped as before.
Change-Id: Ic76c58e233869a60c3a8a27c2efc2182b3a4442d
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1863
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The Agesa wrapper and UDELAY_TIMER2 define their own timer functions,
so don't shove in UDELAY_IO
Change-Id: Ibe3345e825e0c074d5f531dba1198cd6e7b0a42d
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1864
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This code used a special case for checksum calculation to
prevent the century byte from messing things up, since
writes "sometimes" didn't happen.
That should be stable now, so the special case isn't necessary.
Downside: On century rollovers (ie. 1999-12-31, 2099-12-31)
CMOS will be reset to the defaults.
Change-Id: Ibe589a1ec953b7b3ba39be30cebd9fc2b27326ae
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1870
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This ensures that there's only one disable/enable cycle for
the entire rewrite instead for every single byte.
Change-Id: Ic06e6dcb08976d158ff784660838c0fbad875176
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1869
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
In principle this isn't necessary. However there's a byte (or several)
outside the first 14 bytes that are part of the RTC, and require
locking (century/altCentury).
Since their location is mostly unknown, guard writes properly.
Change-Id: I847cd4efa92722e8504d29feaf7dbfa5c5244b4e
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1868
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
intel_irq_routing_table is a local structure that should not be used
globally, because it might not be there on all mainboards.
Instead, the API has to be corrected to allow passing a PIRQ table in
where needed.
Change-Id: Icf08928b67727a366639b648bf6aac8e1a87e765
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1862
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Some boards selected GENERATE_ instead of HAVE_
Change-Id: I450c22d7b044f0c88c21692246d452d516a68a83
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1841
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
- move VGA handling options into devices/Kconfig
- make Devices a top level menu
- move some options "closer" to the code they control
Change-Id: Ia79541d18b2b0d9b89a8b154255e312060627c48
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1840
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Both remaining options, DRIVERS_PS2_KEYBOARD and ID_SECTION_OFFSET
are not likely to go away any time soon, so let's not keep them
in Kconfig.deprecated_options but move them close to the code they
control.
Change-Id: I310b877c5b3d5a3444056641c4aee07a48c4c4be
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1839
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
It's only mentioned in Kconfig and never set nor used.
Change-Id: Icc0ac56ae7b325a9e93ed5cdce9dc4b7bab43140
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1838
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
hard_reset was indeed consolidated and moved into the southbridge
code a while ago, but the config variable was still kept alife, with
some duplicate code.
Change-Id: I60d4a87de916667f6e89353dfbe1a7b9eca380f7
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1837
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
- Add mainboard_smi.c from arch/x86/Makefile if it's there
- Add mainboard's chromeos.c from the chromeos Makefile
Change-Id: I3f80e2cb368f88d2a38036895a19f3576dd9553b
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1835
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This patch is the beginning of a Kconfig cleanup series
- drop CONFIG_HAVE_BUS_CONFIG and add get_bus_conf.c if it
exists in the mainboard directory
- drop duplicate ACPI_SSDTX_NUM from mainboard Kconfig
if it only defines the defaul value of 0
- Add mptable.c, fadt.c, reset.c and ssdtX.asl when they
exist, not based on some Kconfig magic
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Change-Id: Ia14a7116dad6a724af7e531920fee9a51fd0b200
Reviewed-on: http://review.coreboot.org/1832
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The board incorrectly overrides the southbridge hook, so use the
new mainboard hook instead. This change also activates the actual
southbridge hook to enable decode of complete 4 MB flash memory region.
Change-Id: I02c6fe89ae9ad4a7403f024fac875ebd88a8e142
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1831
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
It's a bool, not a number
Change-Id: I70d52c6af6703101dbd534970ec65275902a283d
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1842
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The board was broken for use with CONFIG_PCI_OPTION_ROM_RUN_YABEL.
Change-Id: Ia57d630143386fe637af83b9e7345d0d3750b089
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1854
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
YABEL's version of mainboard_interrupt_handlers() was hidden behind an
inline stub. This fixes it.
Change-Id: Ie53424a8ce074e93a720c0ef94cb39994cacd023
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1853
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Some time ago our CMOS checksum algorithm was changed under the topic:
Fix our CMOS checksum algorithm so it matches what /dev/nvram expects
Here is another copy of the algorithm that had to be updated.
Change-Id: I58659c7b8a89c89c76efdff405ee0620e7302277
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1852
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The VIA chipsets CX700, VT8623 and VX800 required to be
configured with real mode option rom code enabled. This
patch fixes the issue and drops some unneeded header files.
Change-Id: I0d8a3f8f99c2eacec7666f08f85b99f09c06af84
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1833
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
We moved GNVS to it's own section, but forgot to tell the cbmem code
about it. This is purely cosmetical, but add it anyways.
Change-Id: Icb3788c0325ea79cc1efff4a876412d07da7936e
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1782
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The search for save state was comparing the entire RAX
value when it needs to just operate on the bottom byte
so it can find the GSMI command in bits 7:0 but not the
extended command code in bits 15:8.
Change-Id: I526c60e6b3732fa3680a17a4bed2a2ef23ccf94f
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1774
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
At boot time when the ACPI tables are created and the location
of GNVS is determined then save that address for resume time.
This also sets the values of USB charging in S3/S5 to the expected
default values for Stout/Butterfly that were not set correctly.
Change-Id: I9b94b868aa6e81aced06c0262cc2697ad4faf1e6
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1768
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Instead of hijacking some random memory addresses to
relay the GNVS pointer to SMM we can use EBX register
during the write to APM_CNT register when the SMI is
triggered.
Change-Id: I79a89512c40353d72ad058cbf2e6a23a696945da
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1766
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Using global variables with the TSEG is a bad idea because
they are not relocated properly right now. Instead make
the variables static and add accessor functions for the
rest of SMM to use.
At the same time drop the tcg/smi1 pointers as they are
not setup or ever used. (the debug output is added back
in a subsequent commit)
Change-Id: If0b2d47df4e482ead71bf713c1ef748da840073b
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1764
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This is currently used by the ELOG GSMI interface but is a
good way to pass data to SMM so move the current searching code
to a separate function and make it a bit more versatile with the
checks it does to find a match so it can be used in other
situations.
Change-Id: I5b6f92169f77c7707448ec38684cdd53c02fe0a5
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1763
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The SMM GNVS pointer is normally updated only when the
ACPI tables are created, which does not happen in the
resume path.
In order to restore this pointer it needs to be available
at resume time. The method used to locate it at creation
time cannot be used again as that magic signature is
overwritten with the address itself. So a new CBMEM ID
is added to store the 32bit address so it can be found
again easily.
A new function is defined to save this pointer in CBMEM
which needs to be called when the ACPI tables are created
in each mainboard when write_acpi_tables() is called.
The cpu_index variable had to be renamed due to a conflict
when cpu/cpu.h is added for the smm_setup_structures()
prototype.
Change-Id: Ic764ff54525e12b617c1dd8d6a3e5c4f547c3e6b
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1765
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
If the PEI System Agent doesn't run PCIe initialization, the PEG
clock gating will not be setup. Add the PEG clock gating when
pei_data->pcie_init is 0.
Change-Id: I7e31bcebd11feb4807aa29b528adf09fb013c3ce
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/1827
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The IvyBridge reference code does some slow and
extensive PCIe init that we do not need on Link.
Hence, add a flag to disable/enable running that
init code from coreboot.
NMode was used during bringup. We'll switch
the setting back to auto, to let MRC decide the right thing.
Change-Id: Ia989bb9ea079aadfeb41dc3029b7c2c623e84760
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1826
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This will enable DDR3 1.35V support for memory training in
the reference code. It requires the board to be setup for
1.35V with whatever board-specific GPIOs are available.
Change-Id: I14e4686c20f9610f90678e6e3bece8ba80d8621a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1825
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
I added a comment to the pei_data.h to remind users about
how the OC pins are mapped.
Change-Id: I4d74eb69fc78816a69e61260c2c9b2b3e58cafec
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/1824
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Let memory initialization code use the coreboot romstage console. This
simplifies the code and makes sure that all output is available in
/sys/firmware/log.
The pei_data structure is modified to allow passing the console output
function pointer. Romstage console_tx_byte() is used for this purpose.
Change-Id: I722cfcb9ff0cf527c12cb6cac09d77ef17b588e0
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/1823
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Updating microcode on several threads in a core at once
can be harmful. Hence add a spinlock to make sure that
does not happen.
Change-Id: I0c9526b6194202ae7ab5c66361fe04ce137372cc
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1778
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This prepares the way for vboot to inform coreboot when it needs the VGA
Option ROM loaded. Coreboot can't always know when it's needed (with
keyboard-based dev-mode, coreboot can't tell if we're in dev-mode or not).
By the time we get to U-Boot, it's too late, so we need two extra bits - one
for vboot to tell coreboot to load the Option ROM and another for coreboot
to let vboot know it's been done.
This change sets up the communication, but doesn't act on it just yet.
Even with this CL we always load the VGA Option ROM, so there's nothing to
test. There should be no user-visible change.
Change-Id: Ic4e9673a3707b6605064f4879bb3e74d4412322f
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Reviewed-on: http://review.coreboot.org/1822
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
ChromeOS' top of the tree u-boot expects coreboot to export information
about option ROM status (started/not started). Stumpy and Lumpy were
left behind and are not exporting this information. This CL fixes the
problem.
Change-Id: Id90035bd76ab177e4fc269efc2b74f15f641c77d
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/1713
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Fix GPIO exporting for new Vboot for oprom-matters GPIO
and to make the power button static.
Change-Id: Ic042c428a1d43512228c686121fa057d876606e1
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1761
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Several small improvements of the stack checking code:
- move the CPU0 stack check right before jumping to the payload
and out of hardwaremain (that file is too crowded anyways)
- fix prototype in lib.h
- print size of used stack
- use checkstack function both on CPU0 and CPU1-x
- print amount of stack used per core
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Test: Boot coreboot on Link, see the following output:
...
CPU1: stack: 00156000 - 00157000, lowest used address 00156c68,
stack used: 920 bytes
CPU2: stack: 00155000 - 00156000, lowest used address 00155c68,
stack used: 920 bytes
CPU3: stack: 00154000 - 00155000, lowest used address 00154c68,
stack used: 920 bytes
...
Jumping to boot code at 1110008
CPU0: stack: 00157000 - 00158000, lowest used address 00157af8,
stack used: 1288 bytes
Change-Id: I7b83eeee0186559a0a62daa12e3f7782990fd2df
Reviewed-on: http://review.coreboot.org/1787
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
In hardwaremain() we can't add timestamps before we actually
reinitialized the cbmem area. Hence we kept the timestamps in
an array and added them later. This is ugly and intrusive and
helped hiding a bug that prevented any timestamps to be logged
in hardwaremain() when coming out of an S3 resume.
The problem is solved by moving the logic to keep a few timestamps
around into the timestamp code. This also gets rid of a lot of ugly
ifdefs in hardwaremain.c
Change-Id: I945fc4c77e990f620c18cbd054ccd87e746706ef
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1785
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
For reasons of security and testing we want to be able to
enable/disable ME section locking through a config option.
Change-Id: I341c577cdae86be62c0e3d32bbd6b3333c004a5f
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1798
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
- drop changelog and add license header instead
- 80+ character fixes
- make stacks array static because it's not used externally
- rename copy_secondary_start_to_1m_below()
Change-Id: I8b461bea21ee0ddd85ea3a3a923d1e15167f54f0
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1821
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This addition is in support of future multicore support in
coreboot. It also will allow us to remove some asssembly code.
The CPU "index" -- i.e., its order in the sequence in which
cores are brought up, NOT its APIC id -- is passed into the
secondary start. We modify the function to specify regparm(0).
We also take this opportunity to do some cleanup:
indexes become unsigned ints, not unsigned longs, for example.
Build and boot on a multicore system, with pcserial enabled.
Capture the output. Observe that the messages
Initializing CPU #0
Initializing CPU #1
Initializing CPU #2
Initializing CPU #3
appear exactly as they do prior to this change.
Change-Id: I5854d8d957c414f75fdd63fb017d2249330f955d
Signed-off-by: Ronald G. Minnich <rminnich@chromium.org>
Reviewed-on: http://review.coreboot.org/1820
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
There are some function dependancies that didn't work
when MAX_CPU was set to 1 and the build would fail.
Change-Id: I033a42056f7b48a40316e03772ed89ad9cb013fe
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/1819
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
This change allows us to figure out how much of the AP stacks we are
using, as well as to catch any case of an AP overrunning its stack.
Also, the stack is poisoned, which is a good way to catch programming
errors -- code should never count on auto variables being zerod.
The stack bases are recorded in a new array, stacks. At the end,
when all APs are initialized, the stacks are walked and the
lowest level of the stack that is reached is printed.
Build and boot and look for output like this:
CPU1: stack allocated from 00148000 to 00148ff4:\
lowest stack address was 00148c4c
CPU2: stack allocated from 00147000 to 00147ff4:\
lowest stack address was 00147c4c
CPU3: stack allocated from 00146000 to 00146ff4:\
lowest stack address was 00146c4c
Note that we used only about 1K of stack, even though in this
case we allocated 4K (and in the main branch, we allocate 32K!)
Change-Id: I99b7b9086848496feb3ecd207f64203fa69fadf5
Signed-off-by: Ronald G. Minnich <rminnich@chromium.org>
Reviewed-on: http://review.coreboot.org/1818
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
Right now coreboot's build process produces images that are
not booting on actual hardware because they are smaller than
the actual flash device and also don't have an IFD nor an ME
firmware in them. In order to produce bootable images, you
needed a wrapper script / extra step until now. With this
change, the resulting coreboot.rom is actually bootable.
Change-Id: I82714069fb004d4badc41698747a704bd9fed4da
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1771
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The currently encoded register constraints fails compilation
for SMM code or any code that compiles with -fPIC. The reason
is that the ebx register is used for GOT base register.
I don't believe the comment eluding to register constraints for AMD
processors still applies. Therefore remove mmio_conf.h, and use the
mmio methods in io.h.
Change-Id: I391e5c2088ebc760b3a6ed6c37b65bbecab40a5c
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/1801
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
- Adding more and more optional and non-optional parameters
bloated cbfstool and made the code hard to read with a lot
of parsing in the actual cbfs handling functions. This change
switches over to use getopt style options for everything but
command and cbfs file name.
- This allows us to simplify the coreboot Makefiles a bit
- Also, add guards to include files
- Fix some 80+ character lines
- Add more detailed error reporting
- Free memory we're allocating
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Change-Id: Ia9137942deb8d26bbb30068e6de72466afe9b0a7
Reviewed-on: http://review.coreboot.org/1800
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Some of the modules use their own rolled pci_or_configX functions.
Therefore, make them first class so everyone can use them without
copying them.
Change-Id: I9a4d3364c832548dbfe18139c27cce2d60c3316d
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/1797
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Double equal sign like "test a == b" works. It really does, except NetBSD.
But I haven't found any clue in the manual for the command test about "==".
Change-Id: I37254cfeb688fd1092f2e549d24f8eb270f02fd8
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1817
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
If cmos is invalid for any reason, always set the date and time
before marking RTC valid.
Change-Id: Ib9d154802f75221d58bf28ba9c813f2529904596
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/1790
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Remove the duplicate #defines and use what is set in mc146818rtc.h.
Change-Id: Ic471e03c68b591d19c0646fdbea78374af11c8b8
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/1789
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The MRC cache code, as implemented, in some cases uses configuration
settings for MRC cache region, and in some cases - the values read
from FMAP. These do not necessarily match, the code should use FMAP
across the board.
This change also refactors mrccache.c to limit number of iterations
through the cache area and number of fmap area searches.
Change-Id: Idb9cb70ead4baa3601aa244afc326d5be0d06446
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/1788
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Adding an entry for 0x306a0 will make sure that all
CPUs with CPUIDs 0x306aX will execute the driver (analog to
Sandybridge behavior)
Change-Id: I0353f3a48ecfd41274fdf6ee302c7d34482f1b5b
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1783
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
in the resume case, timestamps were collected in RAM stage
but not stored in CBMEM. This leads to only a single time stamp
covering 200ms being available for all of ram stage.
Change-Id: Ibf0bb92caf5e032c12fe4e1b9b84b3624d499511
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1781
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
coreboot uses about 2K of stack on the BSP, and about 1K of stack on the
APs. No reason to use an overdimensonal stack of 32k per core/thread.
Change-Id: I734c240b992d40e1e35db3df5437c36da0a755cf
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1780
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This is a basic romstage driver that can be used for the
MRC cache code on systems where we do not have the MRC cache
stored in a flash region that is memory mapped.
It uses the hardware sequencing interface to avoid having
to know anything about the flash chip itself.
BUG=chrome-os-partner:15031
BRANCH=stout
TEST=manual: this was tested with debug code added to romstage
that attempted to read the MRC cache at offset 0x3e0000.
SPI READ offset=003e0000 size=64 buffer=ff7fba00
SPI ADDR 0x003e0000
SPI HSFC 0x3f00
SPI READ: 0=4443524d
SPI READ: 1=00000bb0
SPI READ: 2=00008e24
SPI READ: 3=00000000
SPI READ: 4=001c8bbb
SPI READ: 5=0c206466
SPI READ: 6=0a043220
SPI READ: 7=000058b4
SPI READ: 8=00000000
SPI READ: 9=00000000
SPI READ: 10=00100000
SPI READ: 11=00100005
SPI READ: 12=20202025
SPI READ: 13=000e0001
SPI READ: 14=00000000
SPI READ: 15=00000000
Change-Id: I5f78f53111f912ff5dda52bbf90fdc1824b82681
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1777
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
If the event log is stored in flash that is not memory
mapped then it must use the SPI controller to read from
the flash device instead of relying on memory accesses.
In addition a new CBMEM ID is added to keep an resident
copy of the ELOG around if needed. The use of CBMEM for
this is guarded by a new CONFIG_ELOG_CBMEM config option.
This CBMEM buffer is created and filled late in the process
when the SMBIOS table is being created because CBMEM is
not functional when ELOG is first initialized.
The downside to using CBMEM is that events added via the
SMI handler at runtime are not reflected in the CBMEM copy
because I don't want to let the SMM handler write to memory
outside the TSEG region.
In reality the only time we add runtime events is at kernel
shutdown so the impact is limited.
Test:
1) Test with CONFIG_ELOG_CBMEM enabled to ensure the event
log is operational and SMBIOS points to address in CBMEM.
The test should involve at least on reboot to ensure that the
kernel is able to write events as well.
> mosys -l smbios info log | grep ^address
address | 0xacedd000
> mosys eventlog list
0 | 2012-10-10 14:02:46 | Log area cleared | 4096
1 | 2012-10-10 14:02:46 | System boot | 478
2 | 2012-10-10 14:02:46 | System Reset
3 | 2012-10-10 14:03:33 | Kernel Event | Clean Shutdown
4 | 2012-10-10 14:03:34 | System boot | 479
5 | 2012-10-10 14:03:34 | System Reset
2) Test with CONFIG_ELOG_CBMEM disabled to ensure the event
log is operational and SMBIOS points to memory mapped flash.
The test should involve at least on reboot to ensure that the
kernel is able to write events as well.
> mosys -l smbios info log | grep ^address
address | 0xffbf0000
> mosys eventlog list
0 | 2012-10-10 14:33:17 | Log area cleared | 4096
1 | 2012-10-10 14:33:18 | System boot | 480
2 | 2012-10-10 14:33:18 | System Reset
3 | 2012-10-10 14:33:35 | Kernel Event | Clean Shutdown
4 | 2012-10-10 14:33:36 | System boot | 481
5 | 2012-10-10 14:33:36 | System Reset
Change-Id: I87755d5291ce209c1e647792227c433dc966615d
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1776
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
- Fix handling of 5-byte Fast Read command in the ICH SPI
driver. This fix is ported from the U-boot driver.
- Allow CONFIG_SPI_FLASH_NO_FAST_READ to be overridden by
defining a name for the bool in Kconfig and removing the
forced select in southbridge config
- Fix use of CONFIG_SPI_FLASH_NO_FAST_READ in SPI drivers
to use #if instead of #ifdef
- Relocate flash functions in SMM so they are usable.
This really only needs to happen for read function pointer
since it uses a global function rather than a static one from
the chip, but it is good to ensure the rest are set up
correctly as well.
Change-Id: Ic1bb0764cb111f96dd8a389d83b39fe8f5e72fbd
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1775
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Applied function attribute to function definition to avoid 'conflicting type' warning.
Function declaration is in src/include/cpu.h
void secondary_cpu_init(unsigned int cpu_index)__attribute__((regparm(0)));
But function definition in lapic_cpu_init.c is missing the "__attribute__" part.
Change-Id: Idb7cd00fda5a2d486893f9866920929c685d266e
Signed-off-by: Han Shen <shenhan@google.com>
Reviewed-on: http://review.coreboot.org/1784
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
The Intel PCH can override the ASPM settings via the MPC2 register.
Add a chip override for F0-F7. Mainboards may implement this as
needed.
This also fixes the final PM setup being done too early. It was
being done prior to the PCIe ASPM setup, which happens in the
bridge scan.
Change-Id: Idf2d2374899873fc6b1a2b00abdb683ea9f5bd6b
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/1796
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Right now the SPI bus is getting set to 20mhz for transactions
initiated with the software sequence interface.
In order to be able to do reasonable fastread/write/erase we
can bump this up to a higher value at boot before it gets
locked at 20mhz.
To do this read out the speed set in the SPI descriptor for
hardware sequencing and apply it to software sequencing.
Change-Id: I79aa2fe7f30f734785d61955ed81329fc654f4a4
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: http://review.coreboot.org/1773
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The chips we are using do not use BE52 (block erase 0x52)
so we can use that opcode menu location to enable fast read.
Change-Id: I18f3e0e5e462b052358654faa0c82103b23a9f61
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: http://review.coreboot.org/1772
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
At least when CONFIG_CHROMEOS is turned on, it's possible for
CONFIG_FRAMEBUFFER_KEEP_VESA_MODE to be set but for there not to be any valid
information to put into the framebuffer coreboot table. That means that what's
put in there is junk, probably all zeroes from the uninitialized global
variable the mode information is stored in (mode_info).
When a payload uses libpayload and turns on the coreboot framebuffer console,
that console will attempt to scroll at some point and decrease the cursor's y
coordinate until it is less than the number of rows claimed by the console.
The number of rows is computed by taking the vertical resolution of the
framebuffer and dividing it by the height of the font. Because the mode
information was all zeroes, the coreboot table info is all zeroes, and that
means that the number of rows the console claims is zero. You can't get the
unsigned y coordinate of the cursor to be less than zero, so libpayload gets
stuck in an infinite loop.
The solution this change implements is to add a new function,
vbe_mode_info_valid, which simply returns whether or not mode_info has anything
in it. If not, the framebuffer coreboot table is not created, and libpayload
doesn't get stuck.
Change-Id: I08f3ec628e4453f0cfe9e15c4d8dfd40327f91c9
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/1758
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
And move the pre-hardwaremain post code to 0x79
so it comes before hardwaremain at 0x80.
Emit these codes from ACPI OS resume vector as well
as the finalize step in bd82x6x southbridge.
Change-Id: I7f258998a2f6549016e99b67bc21f7c59d2bcf9e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1702
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The sleep type is 5 for S3 and 7 for S5.
Change-Id: I7ffdb3d27b6994ac4a12a343caf4d7abb82fe6ca
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1760
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
If these values are non-zero then the kernel will issue
an SMI for each core (cstate) and package (pstate).
Since we don't do anything with these SMI callbacks we
can avoid taking the extra SMIs at boot time by zeroing
these fields.
Change-Id: I3bc5fe0a9f45141d46884cb77ecdfaeaa45d2439
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1769
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The VMX MSR may come up with random values and needs to be
initialized to zero. This was done incorrectly in finalize_smm.
It must be done on a per core basis in the general CPU init.
This touches all Sandybridge and Ivybridge configs.
Change-Id: I015352d0f8e2ebe55ac0a5e9c5bbff83bd2ff86b
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/1794
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The MSR for VMX can start with a random value and needs to be
cleared by coreboot. I am reverting this change, as
it handles almost everything and doing a follow-on change to fix
the improper clearing of the MSR.
Change-Id: Ibad7a27b03f199241c52c1ebdd2b6d4e81a18a4e
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/1793
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The reporting of cores and threads in the system was a bit
ambiguous. This patch makes it clearer.
Change-Id: Ia05838a53f696fbaf78a1762fc6f4bf348d4ff0e
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1786
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
On Sandybridge and Ivybridge systems the firmware image has to
store a lot more than just coreboot, including:
- a firmware descriptor
- Intel Management Engine firmware
- MRC cache information
This option allows to limit the size of the CBFS portion in
the firmware image.
Change-Id: Ib87fd16fff2a6811cf898d611c966b90c939c50f
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1770
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
src/include/timestamp.h is an interface describing timestamp storage
in coreboot. Exporting this interface is complicated by inclusion of
tsc.h which is needed only for the API and is not used in structure
definitions. Including this dependency only when needed fixes the
problem.
Change-Id: Ie6b1460b1dab0f5b5781cb5a9fa89a1a52aa9f17
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/1753
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
These bits are used by the IGD OpRegion code
Change-Id: I89a11fc5021d51e0c1675ba56f6a3bc3b79bb8aa
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1751
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
In order to support Intel's IGD Opregion standard, we need
an additional set of flags shared between firmware, ACPI, SMM, and the
graphics driver.
Change-Id: I1a9b8dff5e5ee8d501b6672bc3bcca39ea65572e
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1750
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
These can be stored in the code segment, since it's never changed.
Change-Id: I8b3827838e08e6cc30678aad36c39249fbca0c38
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1749
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Add support for GigaDevice SPI ROMS.
The GD25Q64B device has been tested, the other rom devices added to the
file have not.
Change-Id: If35676ca6b90329f15667ebb32efa0d1a159ae91
Signed-off-by: Martin Roth <martin@se-eng.com>
Reviewed-on: http://review.coreboot.org/1747
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
These events were initially for Chrome EC but they can be
applied to any EC.
Change-Id: I0eba9dbe8bde506e7f9ce18c7793399d40e6ab3b
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1746
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
If the driver is initialized before the lockdown then it will
fail to work after the lockdown bit is set.
Change-Id: Idc05d33d8d726bf29cb3c9b1b4604522bd64170a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1745
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The RO_FMAP base moved from 0x5f0000 to 0x610000.
Also update Kconfig default and add a descripton so
the default can be changed by boards.
Change-Id: I0caad0ce6e6f19750dbbf042a5a489b558f62b96
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1705
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
http://netbsd.gw.com/cgi-bin/man-cgi?date++NetBSD-current
The NetBSD manual tells us the date in NetBSD doesn't take any flags
to enable or disable padding in the format.
By default, date pads numeric fields with zeroes. This will convert the
number to octal one. So add "0x" to convert it to BCD directly.
Change-Id: Icd44312acf01b8232f1da1fbaa70630d09007b40
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1804
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
The range of weekday in CMOS is 01-07, while the Sunday is 1, and
Saturday is 7. The comand date in coreutils defines
%u day of week (1..7); 1 is Monday
%w day of week (0..6); 0 is Sunday
There are 1 day offset for each week day. So we use "%w" and plus 1
before we update the weekday in CMOS.
Change-Id: I3fab4e95f04924ff0ba10a7012b57da1d3f0d1a5
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1802
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
This makes resume from S3 work again. The check is new and fails on
other boards, too.
Change-Id: I0ada569e4ba649b9ac82768b0888e16104c621e8
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1809
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Read out the post code from the previous boot and
log it if the code is not one of the expected values.
Test:
1) interrupt the boot of the system, this is easiest
with warm reset button when servo is attached
2) check the event log with mosys
65 | 2012-09-09 12:32:11 | Last post code in previous boot | 0x9d
Change-Id: Id418f4c0cf005a3e97b8c63de67cb9a09bc57384
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1744
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This will use 3 bytes of CMOS to keep track of the POST
code for the current boot while also leaving a record of
the previous boot.
The active bank is switched early in the bootblock.
Test:
1) clear cmos
2) reboot
3) use "mosys nvram dump" to verify that the first byte
contains 0x80 and the second byte contains 0xF8
4) powerd_suspend and then resume
5) use "mosys nvram dump" to verify that the first byte
contains 0x81 and the second byte contains 0xFD
Change-Id: I1ee6bb2dac053018f3042ab5a0b26c435dbfd151
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1743
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This is a slight improvement over the rep movsb loop
Change-Id: Id71d9bfe5330b154a5c62fac85ce3955ae89b057
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1742
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The linux kernel relies on the RTC reporting pending interrupts if
the RTC alarm was used to wake the system. If we clear these flags
here then the rtc-cmos driver in the kernel will think that no
interrupts are pending and will not re-start the timerqueue to
handle the alarm timerqueue node.
This flag doesn't exist in SMM but the rtc code is compiled there.
Since rtc_init() is not called by SMM it is guarded with an ifdef.
I performed several thousand suspend/resume cycles without seeing
an issue where hwclock was unable to read from /dev/rtc. There
still is a potential kernel issue where the timerqueue can stall
but this makes that much less likely to happen on resume.
Change-Id: I5a343da4ce5c4c8ec4783b4e503869ccfa5077f0
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1741
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
In case tseg_relocate() is called again on a pointer we should not
relocate it again.
Change-Id: Ida1f9c20dc94b448c773b14d8864afe585369119
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1740
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
We are seeing ME disabled and ME error events on some devices
and this extended info can help with debug.
Also fix a potential issue where if the log does manage to get
completely full it will never try to shrink it because the only
call to shrink the log happens after a successful event write.
Add a check at elog init time to shrink the log size.
Change-Id: Ib81dc231f6a004b341900374e6c07962cc292031
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1739
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The handling of write enable was not entirely correct,
the opcode needs to be skipped when the controller is
locked down.
Addresses were not getting set properly for erase commands
which seemed to mostly work when the previous command had
set an address.
Tested by adding events to the event log at runtime on a
freslhy flashed device (with locked down SPI controller)
until the log log shrink happens to ensure it does not hang:
hexdump -C elog.event.kernel_clean
00000000 01 00 00 00 ad de 00 00 00 00
for x in $(seq 1 232); do
cat elog.event.kernel_clean > /sys/firmware/gsmi/append_to_eventlog
done
mosys eventlog list | tail -6
154 | 2012-09-01 13:54:43 | Kernel Event | Clean Shutdown
155 | 2012-09-01 13:54:43 | Kernel Event | Clean Shutdown
156 | 2012-09-01 13:54:43 | Kernel Event | Clean Shutdown
157 | 2012-09-01 13:54:43 | Kernel Event | Clean Shutdown
158 | 2012-09-01 13:54:43 | Log area cleared | 1030
159 | 2012-09-01 13:54:43 | Kernel Event | Clean Shutdown
Change-Id: I3a50dae54422a9ff37daefce3632f8bcbe4eb89f
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1717
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
When bringing up VGA by running the option rom it's sometimes
useful to get more information about the mode that gets set,
or the reason why the mode could not be set or a picture could
not be displayed. Also prefix the output from VBE mode setting
with VBE:
Copying VGA ROM Image from fff0fd78 to 0xc0000, 0x10000 bytes
Real mode stub @00000600: 867 bytes
Calling Option ROM...
int15_handler: INT15 function 5fac!
... Option ROM returned.
VBE: Getting information about VESA mode 4161
VBE: resolution: 1280x1024@16
VBE: framebuffer: d0000000
VBE: Setting VESA mode 4161
VGA Option ROM has been loaded
Change-Id: I2be11f095dc62ed3c99e0d4272ad9d6521608a44
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1714
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Now that we have FMAP support in coreboot use it to find the
offset in flash for ELOG to use.
If coreboot has elog configured with a smaller size then use
that over the FMAP size. This is because I set aside a 16KB
region in the FMAP but we only use 4KB of it to keep the impact
to boot/resume speed to a minimum.
FMAP: Found "FMAP" version 1.0 at ffe10000.
FMAP: base = 0 size = 800000 #areas = 32
FMAP: area RW_ELOG found
FMAP: offset: 3f0000
FMAP: size: 16384 bytes
FMAP: No valid base address, using 0xff800000
ELOG: base=0x003f0000 base_ptr=0xffbf0000
ELOG: MEM @0x00190ad8 FLASH @0xffbf0000
ELOG: areas are 4096 bytes, full threshold 3072, shrink size 1024
Change-Id: I3d826812c0f259d61f41b42797c58dd179f9f1c8
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1706
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Now that WREN prefix is handled properly ELOG is able to write
when the SPI controller is locked down.
To test, ensure that runtime SPI write via ELOG is successful by
checking the event log for a kernel shutdown reason code:
5 | 2012-08-27 11:09:48 | Kernel Event | Clean Shutdown
6 | 2012-08-27 11:09:50 | System boot | 26
7 | 2012-08-27 11:09:50 | System Reset
Change-Id: If6d0dced7cb0f5ca7038b3d758f31b856826d30b
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1712
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
The code that attempts to use the opmenu needs to have a special
case for write enable now that it is handled as an atomic prefix
and not as a standalone opcode.
To test, ensure that runtime SPI write via ELOG is successful by
checking the event log for a kernel shutdown reason code:
5 | 2012-08-27 11:09:48 | Kernel Event | Clean Shutdown
6 | 2012-08-27 11:09:50 | System boot | 26
7 | 2012-08-27 11:09:50 | System Reset
Change-Id: I527638ef3e2a5ab100192c5be6e6b3b40916295a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1710
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
Check the RTC on boot after RTC battery failure and ensure
that the reported build date matches what is reported:
> grep ^rtc /proc/driver/rtc
rtc_time : 01:00:21
rtc_date : 2012-08-16
Change-Id: If23f436796754c68ae6244ef7633ff4fa0a93603
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1709
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
This appears to fix an infrequent resume hang on Ivybridge.
Tested on 2 devices with 15k suspend/resume cycles each
Change-Id: I53618bc7966824413f1720a2be3cbd2550e29473
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1704
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
(elog portion, support in EC code pending)
- Use a new EC command to read the last post code
from the previous boot
- If the post code is not well-known final boot
or resume code then log it
Change-Id: Id6249e9a182243eb87c777edd56f48de72125e77
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1703
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
Until now, the MRC cache position and size was hard coded in Kconfig.
However, on ChromeOS devices, it should be determined by reading the
FMAP.
This patch provides a minimalistic FMAP parser (libflashmap was too
complex and OS centered) to allow reading the in-ROM flash map and
look for sections.
This will also be needed on some partner devices where coreboot will
have to find the VPD in order to set up the device's mac address
correctly.
The MRC cache implementation demonstrates how to use the FMAP parser.
Change-Id: I34964b72587443a6ca4f27407d778af8728565f8
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1701
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
This is purely cosmetic. All error messages in the Sandybridge raminit
code printed a newline at the end.
Change-Id: I880d291928291d487039850a2a3d53a1101124ba
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1699
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
build.h is generated at build time,
with highly parallel builds, we might try to compile the rtc driver too
early.
Change-Id: I9a2681484d58b67ed3061669fbdf52ac5ad14dab
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-on: http://review.coreboot.org/1698
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
When a power failure happens on the RTC rail, the CMOS memory (including
the RTC registers) is filled with garbage.
So, we erase the full first bank (112 bytes) and we reset the RTC date
to the build date.
To test, disconnect the CMOS battery to produce an RTC power
failure, then boot the machine and observe the RTC date is the build
date using "cat /sys/class/rtc/rtc0/date"
Change-Id: I684bb3ad5079f96825555d4ed84dc0f7914e9884
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-on: http://review.coreboot.org/1697
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
Each G34 socket has two node. Previous lapic algorithm is written for
the CPU which has one node per socket. I test the code on h8qgi with
4 family 15 CPUs(8 cores per CPU). The topology is:
socket 0 --> Node 0, Node 1
socket 2 --> Node 2, Node 3
socket 1 --> Node 4, Node 5
socket 3 --> Node 6, Node 7
Each node has 4 cores.
I change the code according to this topology.
Change-Id: I45f242e0dfc61bd9b18afc952d7a0ad6a0fc3855
Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com>
Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/1659
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
This will allow the lower bank to be cleared without impacting the
ability to suspend/resume.
Change-Id: Iaec3c9e7e40c334053c814eaddd1f614df245a73
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1696
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
On Panther Point PCH (and maybe cougar point), when some of the register
D reserved bits are set, the RTC starts misbehaving (e.g. incrementing
the year byte every second).
There are probably undocumented features implemented behind those bits.
Let's reset register D to a known state to ensure we get the expected
RTC behavior.
Change-Id: I7e2c2a2c6130a974bccb3d760b41eaa579a58b67
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-on: http://review.coreboot.org/1695
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
We always define CONFIG_ variables, even if they're not set.
Hence, remove the check whether CONFIG_UDELAY_TIMER2 is defined
Change-Id: Iefdf2389941f2cc63ae4f13ac6b213da4c96b201
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1694
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
Right now we only had a post code for "All devices enabled" which
was emitted at the wrong time (after the device initialize stage
rather than the device enable stage)
Change-Id: Iee82bff020de844c7095703f8d6521953003032c
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1693
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
Our linker script for romstage checks for global variables and
makes the build fail if there are any (on non-AMD systems).
This is great, but having the build fail without any indication
which variables are global is not very useful.
Moving the check to the Makefile allows us to let the linking stage
succeed and reveil which variable names end up in the data and bss
sections of the binary.
To test, add "int foo;" as the first line in src/mainboard/samsung/lumpy/romstage.c
and build coreboot for Lumpy. See the build break the following
way:
LINK cbfs/fallback/romstage_null.debug
Forbidden global variables in romstage:
00006a84 B foo
Change-Id: I3c8780888f46a6577ffd36bcea317997b4f84f6f
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1692
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
To allow easy experimentation with thermals, leave power control
registers unlocked.
Change-Id: Ia53065f3f220c2faed58e7d53e60c3f169ae58ec
Signed-off-by: Sameer Nanda <snanda@chromium.org>
Reviewed-on: http://review.coreboot.org/1688
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
Every line of text after a 'help' label in a Kconfig
file must have the same whitespace preceding it, otherwise
it's no longer considered help text.
Change-Id: I97093bee72b295b315d78d4c26d7186bf1017fda
Signed-off-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-on: http://review.coreboot.org/1687
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
PCIE devices are detected and initialized by the AMD PCIe init functions,
which is in cimx rd890. The parameters are read from devicetree.cb before PCIe init.
Now, all bridges and devices are trained on the device 0.0 enable.
After PCIe init, the PCIe ports with devices are on and the PCIe ports
without devices are off. so resources may be allocated correctly
during the rest of the PCI scan.
But if the devicetree was being used to enable/disable devices after initialization,
the problems would arise. Take a look at the serial log:
do_pci_scan_bridge for PCI: 00:02.0
PCI: pci_scan_bus for bus 01
PCI: pci_scan_bus returning with max=001
do_pci_scan_bridge returns max 1
do_pci_scan_bridge for PCI: 00:03.0
PCI: pci_scan_bus for bus 02
PCI: pci_scan_bus returning with max=002
do_pci_scan_bridge returns max 2
do_pci_scan_bridge for PCI: 00:04.0
PCI: pci_scan_bus for bus 03
PCI: pci_scan_bus returning with max=003
do_pci_scan_bridge returns max 3
PCI bridge 02.0, 03.0 and 04.0 are not inserted devices, but these bridges
are still scanned. This is not correct.
Change-Id: I87dac5f062c6926081970ed0c5f26a7e3f447395
Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com>
Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/1640
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
There are four mainboards using agesa family15 code:
Supermicro h8scm and h8qgi, Tyan s8226 and AMD dinar.
All of these boards' PCI domain starts from 0x18.0. Take h8scm as
an example, PCI devices from 0.0 to 0x14.5 is under 0x18.0.
Now, the PCI domain's scan bus function stats from 0.0. This would
result to the PCI devices be scanned twice. Because when the function
run to device 18.0, it would scan from 0.0 again.
This issue would result to 2 problems:
1) PCI device may be assigned two different PCI address.
If this happenned on VGA device, coreboot maybe not load
vga bios correctly.
2) coreboot initializes rd890's IO APIC twice.
So this patch scans from 0x18.0 and could resolve the problems above.
Change-Id: I90fbdf695413fd24c7a5e3e9b426dc7ca6e128b1
Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com>
Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/1639
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
Adds lowlevel handling of DMAR tables for use by mainboards'
ACPI code. Not much automagic (yet).
Change-Id: Ia86e950dfcc5b9994202ec0e2f6d9a2912c74ad8
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1654
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Compose the name from Kconfig strings instead.
As the field is for debug print use only, a minor change in the output
should do no harm. The strings no longer include word "Mainboard".
Change-Id: Ifd24f408271eb5a5d1a08a317512ef00cb537ee2
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1635
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This is the smallest possible change to make early_serial.c
compile when included from romstage.c.
early_serial could be reworked to be built as separate unit
(romstage-y), but that should be done for all SuperIOs,
not some individual outlier.
Change-Id: I90ee66b43c9677b86b1b5d6fcc8febfbe58d80dd
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1686
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
All of these capabilities exist on all CPUs supported on
this socket.
Change-Id: I54f34e48e34bb6ab5b9954ab7ece8c2c3a1a8e67
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1664
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The constant field "name" in chip_operations is common to multiple
different devices within a chip and cannot reflect the actual device
as found on the platform.
The intention is that a driver sets dev->name as part of the device
enumeration sequence with the detected hardware type and revision.
The field is for debug print use only.
Change-Id: Ib7bf90ba3c618ad0cb715d80d6a937ceaae0adcf
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1634
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This adds proper support for turbo and super-low-frequency modes.
Calculation of the p-states has been rewritten and moved into an
extra file speedstep.c so it can be used for non-acpi stuff like
EMTTM table generation.
It has been tested with a Core2Duo T9400 (Penryn) and a Core Duo T2300
(Yonah) processor.
Change-Id: I5f7104fc921ba67d85794254f11d486b6688ecec
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1658
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Because enable cache is added at the end of disable_cache_as_ram,
( http://review.coreboot.org/#/c/1662/2/src/cpu/amd/agesa/cache_as_ram.inc )
enable_cache() should be removed. The 3 mainboards are: amd parmer,
amd thatcher and tyan s8226
Change-Id: If870ca07d2e97b9e860a2e2315f551251c7a4ed2
Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com>
Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/1669
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
add this code according to src/include/cpu/x86/cache.h ,line 92,
functin enable_cache()
Change-Id: Ida96a98397eeed98dd61ca979e8c5a33bf00f9e5
Signed-off-by: Siyuan Wang <SiYuan.Wang@amd.com>
Signed-off-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-on: http://review.coreboot.org/1662
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
We parsed the MSR the wrong way, and didn't support some valid values.
Change-Id: Ia42e3de05dd76b6830aaa310ec82031d36def3a0
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1656
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Unfortunately the reference tool chain was updated
without ever even testing it on an abuild run. This
broke a number of ports.
This change gets coreboot at least compiling again
for all supported systems.
Change-Id: I92c7cbc834de6d792fdab86b75df339e2874c52e
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1670
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
We had only some MSR definitions in there, which are used in speedstep
related code. I think speedstep.h is the better and less confusing place
for these.
Change-Id: I1eddea72c1e2d3b2f651468b08b3c6f88b713149
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1655
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Current ExecuteFinalHltInstruction function doesn't work well.
(at least in configuration
Supermicro board with Orochi AMD Opteron processors (model OS6234WKTCGGU))
System reboots when trying to halt core 2,4,6,8 or 10
(OS6234WKTCGGU is 12 core processor)
Based on this information, i think that code doesn't really work with
f15 compute unit (CU) system.
Replacing ExecuteFinalHltInstruction function with
analogous function from f15tn family code fix this problem.
Both functions written from the same cahalt.asm file, but f15tn version
seems more completed
Change-Id: I3942abcdf21f1b86a44c01cc477714e44a40b9cf
Signed-off-by: Kostr <aladyshev@nicevt.ru>
Reviewed-on: http://review.coreboot.org/1569
Tested-by: build bot (Jenkins)
Reviewed-by: Siyuan Wang <wangsiyuanbuaa@gmail.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
Enable the PCIE bridge which is connected to the PCIE slot.
Change-Id: I1b3fb59990e06d7bc7cf19639f2b93dbb7bf9b3e
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1098
Tested-by: build bot (Jenkins)
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
We only want to add data once per device. Using the one in
chip_operations is not very usable anyway, as different
devices under the same chip directory would need to output
entirely different sets of data.
Change-Id: I96690c4c699667343ebef44a7f3de1f974cf6d6d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1492
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins)
The number read from the io-apic register represents the index of the
highest interrupt redirection entry, i.e. the number of interrupts
minus one.
Change-Id: I54c992e4ff400de24bb9fef5d82251078f92c588
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1624
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The options are shown regardless of payload if CONFIG_EXPERT is set.
Change-Id: I12c81ce41a0e300e852481424eadc83f281863bf
Signed-off-by: Peter Stuge <peter@stuge.se>
Reviewed-on: http://review.coreboot.org/1638
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Also clarify that enabling these options is generally not desirable if
using SeaBIOS as payload since the option ROMs are run by SeaBIOS with
more complete BIOS interrupt services available than coreboot.
Change-Id: Ic4a45c351a4933aedad08d70a088eab04ca35b05
Signed-off-by: Peter Stuge <peter@stuge.se>
Reviewed-on: http://review.coreboot.org/1636
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The PCI registers should be accessed aligned and 0x62 is not 32bit
aligned therefore this patch changes it to a 16bit access.
Change-Id: I00725a4569f471eedb061834f626911b42e734fb
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-on: http://review.coreboot.org/1631
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
Aaron Durbin