It's shut down, but UMA memory is not reclaimed. A later extension
could optionally do the magic register dance that allows initialization
of IGD as secondary graphics device.
Change-Id: I2a92bb71755005b886a8e1825325c678a9991bf2
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1252
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Set the default location of hudson firmware to 3rdparty.
Move UMA code from mainboard to northbridge.
Change-Id: I11afea0c7fd04aa84a629dc762704c42baf002df
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1241
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
It defaults to true, and isn't disabled anywhere in the tree.
I also couldn't think of a case where it's actually useful.
Change-Id: I126a47625d5294f3cfff225629f2a948a83c9b7e
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1250
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
One could not pass a device of type APIC to PCI resource functions.
The correct CPU model specific cpu->ops is set at later time in
cpu_initialize().
Change-Id: Ifa274185e4db3080433c1f07e3a48f2b55c0514f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1180
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Northbridge code incorrectly adjusted the last cacheable memory
resource to accomodate room for UMA framebuffer. If system had
4GB or more memory that last resource is not below 4GB and not
the one where UMA is located.
There are three consequences:
The last entry in coreboot memory table is reduced by uma_memory_size.
Due the incorrect code in northbridge code state.tomk,
end of last resource below 4GB, had not been adjusted.
Incrementing that by uma_memory_size diverts a region
possibly claimed for MMIO to RAM, as TOP_MEM is written.
Since the UMA framebuffer did not have IORESOURCE_CACHEABLE,
it was ignored from the MTRR setup and not set uncacheable.
The setting of TOP_MEM and TOP_MEM2, as well as all the MTRRs,
should be copied from BSP to all APs instead of deriving the data
separately for each Logical CPU.
Change-Id: I8e69fc8854b776fe9e4fe6ddfb101eba14888939
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1217
Tested-by: build bot (Jenkins)
Reviewed-by: Denis Carikli <GNUtoo@no-log.org>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
These boards had identical UMA code:
amd/dbm690t
amd/pistachio
technexion/tim5690
technexion/tim8690
The ones below had whitespace or debug level change
compared to the one above:
kontron/kt690
siemens/sitemp_g1p1
These boards use AMDFAM10 guidelines in code:
asrock/939a785gmh
amd/mahogany
Change-Id: Id7c3f48035727f5847f2d7c3a6e87a3d15582003
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1210
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Following boards had identical code:
advansus/a785e-i
amd/bimini_fam10
amd/mahogany_fam10
asus/m5a88-v
avalue/eax-785e
gigabyte/ma78gm
iei/kino-780am2-fam10
jetway/pa78vm5
Following boards had identical code:
amd/tilapia_fam10
asus/m4a78-em
asus/m4a785-m
gigabyte/ma785gm
gigabyte/ma785gmt
In between the two, only whitespace difference.
Change-Id: Iaa48cc7b0038ebcc81be49219b4fc87670aa9941
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1209
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Following boards had identical code:
amd/inagua
amd/persimmon
The following had only whitespace or debug level changes
compared to ones above.
amd/union_station
amd/south_station
asrock/e350m1
Change-Id: I11ee46e06e1dd510cba551166189ebcaa144464b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1208
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Use of the uma_memory_base and _size variables is very scattered.
Implementation of setup_uma_memory() will appear in each northbridge.
It should be possible to do this setup entirely in northbridge
code and get rid of the globals in a follow-up.
Change-Id: I07ccd98c55a6bcaa8294ad9704b88d7afb341456
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1204
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Like ram_resource(), but reserved and not cacheable.
Switch all AMD northbridges to use this one.
Change-Id: I88515c6a0f59f80fd8607c390d0d4a2a35d805f2
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1203
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The current code didn't reserve static resource the right way.
Also reduce TOLM to 0xd0000000, because those boards have so many PCI
devices that 0xe0000000 isn't sufficient.
Change-Id: Ia75a81905eea1a096aed464b63ac154e044bc99c
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1220
Tested-by: build bot (Jenkins)
Don't stop if RAM init fails at first try. It's better to restart
and try again instead of failing on the first try if the second
try would have worked.
Change-Id: Ib5660265d5b10a01588f2e4022dac2ee34f2c6d0
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1191
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: build bot (Jenkins)
This is mostly necessary for reboot, but it doesn't hurt the boot process.
On reboot explicitely reset the integrated graphics, otherwise the VGABIOS
might not be able to reinitialize it properly, and you either have a still
of the last pre-reboot image, garbage or an empty screen, but no text-mode.
Change-Id: Ic3d6932fbaf720d88daaac7e4b09c3c0b9f0b0e2
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1178
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
The wrapper for Trinity. Support S3. Parme is a example board.
Change-Id: Ib4f653b7562694177683e1e1ffdb27ea176aeaab
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1156
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The constant value 0x100000000 is used in linker scripts to calculate
offsets from the end of 32-bit-addressed memory. There is nothing
wrong with it, but 32-bit versions of ld do the calculation wrong.
Change-Id: I4e27c6fd0c864b4d98f686588bf78c7aa48bcba8
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1129
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
As Mathias Krause pointed out, using movw/outw on %al is clearly invalid.
Let's do another typo fix...
Change-Id: Ib95832a11097f599a236ab30c64c26ef429a1699
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1119
Tested-by: build bot (Jenkins)
Reviewed-by: Mathias Krause <minipli@googlemail.com>
Peter and Ron pointed out two typos. They have no side effects, but
it's still worth to fix them.
Change-Id: I9aecccdbc72beb2623fbe558a06e4f1b050f6e74
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1117
Tested-by: build bot (Jenkins)
Not doing a hard reset leaves the BOFL0 register cleared, which
prevents the BSP selection from working. To make sure we start
with known values, use the SPAD0 register for soft reset detection.
If there's a value other than 0, do a hard reset.
Change-Id: I390e3208084cfd32d73cce439ddf2bc9d4436a62
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1103
Tested-by: build bot (Jenkins)
Originally, ChromeBooks would get the offset of the MRC cache
from an entry in the u-boot device tree. Not everyone wants to
use u-boot on Sandybridge systems, however.
Since the new code (based on Kconfig) is now fully working, we
can drop the u-boot device tree remnants.
Change-Id: I4e012ea981f16dce9a4d155254facd29874b28ef
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1051
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The MRC region is described by Kconfig variables, no further math
or parsing is required at this point.
Change-Id: I290d8788b69ef007e9ea2317ce55aefa2d791883
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1046
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Remove all the repeated sections of code in cbtypes.h and place it
in a common location. Add include dir in vendor code's Makefile.
Change-Id: Ida92c2a7a88e9520b84b0dcbbf37cd5c9f63f798
Signed-off-by: Vikram Narayanan <vikram186@gmail.com>
Reviewed-on: http://review.coreboot.org/912
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
Requirements:
- must be in ramstage (locking flash while executing code from there
might not work)
- must be after cbmem is reinitialized (so the mrc cache copy of the
current run can be found)
Change-Id: I8028fb073349ce2b027ef5f8397dc1a1b8b31c02
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/1002
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
- Separate Sandybridge from ChromeOS a bit
The Sandybridge code depends on chromeos features a whole lot.
As a first step, provide a code path to look up the MRC cache
without depending on u-boot.
- Move mrc cache handling to separate file
This enables us to handle the MRC cache from ramstage,
where we can write the flash safely (eg. to update the
cache).
Also teach it to lookup the current MRC cache from CBMEM,
as the original data block isn't available anymore.
After all the preparations, finally write to the SPI
as necessary. It's a simple round robin wear levelling
that erases the entire MRC cache region when it's full
and starts from the beginning.
Change-Id: I4751385574cf709b03d5c9d153b7481ffc90ce12
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/1001
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Replace #elif (CONFIG_FOO==1) with #elif CONFIG_FOO
find src -type f -exec sed -i "s,\(#.*\)(\(CONFIG_[A-Z0-9_]*\)[[:space:]]*==[[:space:]]1),\1\2,g" {} +
(manual tweak since it hit a false positive)
Replace #elif (CONFIG_FOO==0) with #elif !CONFIG_FOO
find src -type f -exec sed -i "s,\(#.*\)(\(CONFIG_[A-Z0-9_]*\)[[:space:]]*==[[:space:]]0),\1\!\2,g" {} +
Change-Id: I8f4ebf609740dfc53e79d5f1e60f9446364bb07d
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/1006
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Martin Roth <martin@se-eng.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This fixes my build when specifying an absolute path to the binary.
Change-Id: I95fb3960be70f78146c6afeb9cc777dccdca6b5b
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/987
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
It is important to have the system configuration reported as early as
possible to have a better idea what exact chipset the platform is
running with.
This change adds code to have an early coreboot module report the CPU
and PCH information. CPU info includes the 32 bit feature information
word, the symbolic processor brand string, and information about some
features support, as obtained through CPUID instructions.
The PCH information includes the symbolic device name and PCI device
version.
Change-Id: If6c21ad5ffb76d7d57d89f4f87d04bdd7192480a
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/975
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
- New table for GT1
- Updates to GT2 17W table
- New table for GT2 35W SKU
- New table for GT2 Other
This also includes a workaround to poll on a different register
when deasserting force wake. On some SKUs the kernel is hanging
when bringing up graphics unless this register is also polled.
Change-Id: I2badf62b464e901cfb0eaf4fc196f59111c71564
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/974
Tested-by: build bot (Jenkins)
- Add config options to set backlight registers
- Update powermeter weight tables for IvyBridge GT1 and
add a new table for GT2 SKU
- Fix a few registers used during GPU PM init sequence
Change-Id: I1500bc07e3ba1bc10c77e7856089e716489dc07a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/973
Tested-by: build bot (Jenkins)
This is done inside the SystemAgent binary on Ivybridge.
Change-Id: I8fb0f593a65a4803e160b284c21b9d5021e2e4a0
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/970
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The ASPM setting for the Direct Media Interface should no longer be done on
Ivybridge/PantherPoint based systems.
Change-Id: Id30de1beb1b162564048e76712736ccf7049dc7c
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-on: http://review.coreboot.org/969
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This fixes a few cosmetics with the following three boards:
- Intel Emerald Lake 2
- Samsung ChromeBook
- Samsung ChromeBox
The following issues were fixed:
- rely on include path in ASL code instead of specifying relative
paths
- use updated ALIGN_CURRENT in acpi_tables.c
- use preprocessor defines instead of hard coded values where possible
Change-Id: Ia5941be3873aa84c30c13ff2f0428d1c52daa563
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/963
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins)
This code is still using libfdt which was denied for inclusion
in coreboot, so it won't compile as is.
Without MRC cache, waking from suspend won't work, and cold boots are
significantly slower (adds around 300-400ms per channel IIRC).
A rework of this code is currently in the works, but will take a little bit
more time (and should not hold back the mainboards being merged)
Change-Id: Ifb9e7d7b86c1f52378803a748810da0d51b58384
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/948
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
AMD supplies their video bios for the Family 14h processor line
with Vendor ID: 1002, Device ID: 9802. This rom should work for
Device IDs 9802-9809. This patch maps all those device IDs to
0x9802 so coreboot will be able to load the vbios. If a vbios
rom using the ACTUAL Device ID is loaded, this function will not
be called.
This file should contain of all Family 14h Graphics PCI IDs so
that they don't need to be overridden on a per mainboard basis.
Change-Id: If3d4a744b3c400dea9444a61f05382af2b2d0237
Signed-off-by: Martin L Roth <martin@se-eng.com>
Reviewed-on: http://review.coreboot.org/955
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
- When calling map_oprom_vendev() the vendor ID and device ID
are joined into a 32 bit value. They were reversed from the
order that I would have expected - Device ID as the high 16 bits
and the Vendor ID as the low 16. This patch reverses them so
so that the the dword comparison in map_oprom_vendev() matches
what's entered into Kconfig for vendor,device.
- Change files calling map_oprom_vendev()
Change-Id: I5b84db3cb1a359a7533409fde7d05fbc6ba3fcc4
Signed-off-by: Martin L Roth <martin@se-eng.com>
Reviewed-on: http://review.coreboot.org/938
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Cougar Point southbridge does udelay in SMM, hence add it on Sandybridge
systems.
Change-Id: I6e5520ca27e7c6eaae632992fb68612067bc1e30
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/937
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
No longer include northbridge files directly in the source for
mainboard romstage.c and fix includes.
Also make required adjustments to function declarations.
Change-Id: Iafdcc0766ed44c64cc628e5935eef2c6372f5f22
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/906
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
It takes about 3 seconds to scrub 8GiB DDR266 RAM.
After ECC scrub XIP cache is disabled for system stability. There is
very little to do in romstage after ECC scrub, especially when RAM
debug messages are turned off. So the delay caused by this is hardly
noticeable.
Cache for complete ROM is re-enabled before ramstage is decompressed,
and it has no unstability issues. So the code required to re-enable
cache for ROM currently already exists in cache-as-ram_ht.inc.
A Kconfig option HW_SCRUBBER enables the scrub to be run on hard
reboots and power-ons.
Change-Id: Icf27acf73240c06b58091f1229efc0f01cca3f85
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/905
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Drop comments (from e7501 era) which no longer seem to apply with
e7505. Write the semi-constant D0:F0 table as code. Some register
settings seem to be in different order compared with vendor BIOS,
and will be handled by follow-up patches.
Split RCOMP register copy function in two parts.
Drop some uses of inline and local_mdelay().
Change-Id: I8739d3b2bbad5861118e8b16ccea1dd86991204f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/896
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
Makes the code a bit more readable, IMO. There is no clean way
to implement this as the affected registers are undocumented.
Seems ROMCC cannot handle the enum. Also any of my future changes
would not be even abuild tested as there is no longer a board with
ROMCC and this chipset. E7505 chipset is CAR only from now on.
Change-Id: I0e2d8ba0c7ed7cce46d9eafb8d8badf04cf75f7a
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/895
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
1. Move the Stack to high memory.
2. Restore the MTRR before Coreboot jump to the wakeup vector.
Change-Id: I9872e02fcd7eed98e7f630aa29ece810ac32d55a
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/623
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
Some places still hardcoded the address instead of using IO_APIC_ADDR.
Change-Id: I3941c1ff62972ce56a5bc466eab7134f901773d3
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/677
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Fix delay loop comments. Time waited and the comments did not match
in the origin (e7501), so delays currently "just work".
Move reset detection to main raminit and don't use generic
sdram_initialize for now, as there are local debug
functions I need to use. Fix AOpen respectively.
Disable ecc scrub, until I have it fixed for cache-as-ram use.
Change-Id: I0529297f43c565d30b5fb7d1836700278ac029c4
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/883
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Drop maybe-prefix in registers and tables.
Have a name in place of PCI_DEV(x,y,z) to avoid confusion.
Change-Id: I88f51b50d7fd83294aa14455a83418630e1bab85
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/882
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
So far the it just setups the internal resource management for coreboot and
detects the memory size.
Change-Id: I8506390fa6656abfa40d92b8f6ede9b91fe98680
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Reviewed-on: http://review.coreboot.org/807
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The Fam15 northbridge.c had hardcoded the CBMEM size. It should use
the one in cbmem.h instead.
Change-Id: I8a00e05884bdb1d1a4a012433b0adfbb9eb22983
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/796
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
The Fam12 northbridge.c had hardcoded the CBMEM size. It should use
the one in cbmem.h instead.
Change-Id: I1eca18e21fa59ae32e802d8452e42e8b7a3575cf
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/795
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
The Fam10 northbridge.c had hardcoded the CBMEM size. It should use
the one in cbmem.h instead.
Change-Id: Id6c4128d8f5f6a417f83daa3a39b2bfc8e810f8a
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/794
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
Also any CPU_AMD_AGESA_FAMILYxx selects CPU_AMD_AGESA, so remove
the explicit selects from the mainboards.
Change-Id: I4d71726bccd446b0f4db4e26448b5c91e406a641
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/792
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Kconfig leaked XIP_ROM_SIZE to other platforms and also
defined obsolete option XIP_ROM_BASE.
Alias AMD_AGESA as NORTHBRIDGE_AMD_AGESA.
Break the circular dependency with family15 Kconfig.
Change-Id: Ic7891012220e1bef758a5a39002b66971d5206e3
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/773
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Use NORTHBRIDGE_INTEL_I945 to select the driver directory for build.
Use _SUBTYPE_945GC and _SUBTYPE_945GM to define at compile-time
which model of I945 the driver is built for.
Change-Id: I11b1e0998d0fc28f8946bad4f0989036a9b18af4
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/684
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Use separate Kconfig option to select a driver directory for
build and the specific type of southbridge to support.
Change-Id: I9482d4ea0f0234b9b7ff38144e45022ab95cf3f3
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/685
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The Fam14 northbridge.c had hardcoded the cbmem size. It should use
in cbmem.h instead.
Change-Id: I910329fc98a4cf04dc81ef66f3aa05a1916f5b1d
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/790
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
Also mark the corresponding lint test stable.
Change-Id: Ib7c9ed88c5254bf56e68c01cdbd5ab91cd7bfc2f
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/772
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The logic was backwards on the ECC enable/disable option. Also added better
debug output when the debug RAM init feature is enabled.
Change-Id: I60bffb6149d96cac65011247ef51cd06ed2210c6
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/670
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The current directory is always part of the search path of cpp when
using #include "..."
Change-Id: I74fe39e0c79835e4b9a927afcbeab21040d8ae52
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/648
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
In the spirit of the earlier renames.
Change-Id: I458a42c79a164483120169d1822ffa6861cc3aff
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/647
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Fix issues reported by new lint test.
Change-Id: I077a829cb4a855cbb3b71b6eb5c66b2068be6def
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/646
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
If both FSBs on i5000 are equipped with CPU packages, one CPU
from each package is elected as BSP. To prevent races between
both BSPs, hlt the second BSP.
Change-Id: I6bfcb17d34e9f028280acff1694309e37307ec21
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/615
Tested-by: build bot (Jenkins)
Originally brought up by Sven Schnelle in March 2011
http://patchwork.coreboot.org/patch/2801/http://www.coreboot.org/pipermail/coreboot/2011-March/064277.html
On some mainboards it may be neccessary to reset early during resume
from S3 if the SLFRCS register indicates that a memory channel is not
guaranteed to be in self-refresh.
On other mainboards, such as Lenovo X60 and T60, the check always
creates false positives, effectively making it impossible to resume.
The SLFRCS register is documented on page 197 of
Mobile Intel® 945 Express Chipset Family Datasheet
Document Number: 309219-006
which is publically available, and the register indicates if a memory
channel is guaranteed to be in self-refresh mode (if bit = 1), or that
a memory channel *may or may not be* in self-refresh mode (if bit = 0).
The register can thus only be used to positively learn that memory is
in self-refresh. It is not known for sure that memory is *not* in
self-refresh. The register is reset by the PWROK signal, which *should*
go low during S3, and go high again when resuming, so it is unsurprising
that SLFRCS has already been cleared when we read the register.
Sven's measurements of the CKE signal on a ThinkPad shows that memory
remains in self-refresh indefinitely, until coreboot re-initializes the
memory controller, even when SLFRCS bits were = 0.
Boards which require a warm reset when SLFRCS bits are cleared must now
explicitly enable the check in the mainboard Kconfig file.
This commit selects the new option in all existing i945 mainboards.
A follow-up commit will remove the option for ThinkPads.
Change-Id: I02320675efb8fde05c371ef243ba5093a4da6d11
Signed-off-by: Peter Stuge <peter@stuge.se>
Reviewed-on: http://review.coreboot.org/590
Tested-by: build bot (Jenkins)
Reviewed-by: Sven Schnelle <svens@stackframe.org>
The comparision is the wrong way round: as long as tsc
is below tsc1, the timeout is not reached
Change-Id: I75de74ef750b5a45be0156efaf10d7239a0b1136
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/530
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The old SSDT ACPI code would only include the AGESA or the coreboot SSDT. Now
include both. AGESA generates the Pstate SSDT and the second coreboot SSDT is
for TOM and TOM2. Now, generate the coreboot SSDT instead of patching it. This
fixes some ACPI errors in Linux and Windows bluescreens.
The Persimmon acpi_tables.c is where the main changes were made and then
replicated in the other Fam14 boards. Please test the other mainbords if you
have one.
Change-Id: I808c863597e024e3e8aeec0821e8618d96cc96a6
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: http://review.coreboot.org/516
Tested-by: build bot (Jenkins)
Reviewed-by: Kerry Sheh <shekairui@gmail.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Apply the normal method of recursively including subdirectories
for src/vendorcode. Remove redundant references under
mainboard and northbridge.
Change-Id: I914a6e262ed2abe83f407df36fe5c1af5eb4bcb0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/468
Tested-by: build bot (Jenkins)
Reviewed-by: Kerry Sheh <shekairui@gmail.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Adapted from northbridge/intel/e7501 with only minor changes.
This commit provides minimal patch from e7501 and I prefer any
cosmetic clean-up to be done after initial merge.
Due the incomplete register specifications, it is safer to have
e7505 as a separate directory in case I improve it to support
wider range of memory configurations. I have no e7501 to test with.
Change-Id: Iba3bf9d69ff5e9d9ef3a6ebf8259f048c55d637d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/295
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Choice between printk/print_ is related to CAR, but really
depends whether we compiled with GCC or ROMCC.
Change-Id: I9fe831a215736462e8b3f4b96ffe231133ecf79b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/347
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
config.h defines also unset config options (as "0") so #ifdef
matches both settings, which isn't what we want.
Change-Id: I694e1b8a8ec4c20225d7af1a13a2a336f900e643
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/293
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Add a ACPI Source Language snippet which if included as
shown in the comments in the file, exposes the 4 possible
temperature sensors in the CPU as ACPI thermal zones.
Change-Id: I94dd773108e348a0fdb9d2f8d6cfe415d5fa0339
Signed-off-by: Christoph Grenz <christophg+cb@grenz-bonn.de>
Reviewed-on: http://review.coreboot.org/222
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
The hp/dl145_g1 motherboard did not work since commit
1f7d3c5672 (svn 6124). That commit added
TINY_BOOTBLOCK for amd8111 southbridge. The result was that the boot process
stopped very early (no console output whatsoever). The same symptom was
reported on other AMDK8 based boards with amd8111 southbridge chips. This
commit seems to fix the bug. It adds a bootblock.c under
src/northbridge/amd/amdk8 that calls enumerate_ht_chains. Probably the
problem was that enum_ht_chains needs to be called before the southbridge
bootblock.c function, not after.
Change-Id: I74fb892aa39048e2d0e76c081b713f825d67f2d4
Signed-off-by: Oskar Enoksson <enok@lysator.liu.se>
Reviewed-on: http://review.coreboot.org/235
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Marc Jones <marcj303@gmail.com>
the patch file comes from
src/vendorcode/amd/agesa/f12/Proc/CPU/Family/0x10/RevE
/F10MicrocodePatch010000bf.c
Change-Id: If701c8a908edf1c486665d3ce4df65da0f65c802
Signed-off-by: QingPei Wang <wangqingpei@gmail.com>
Reviewed-on: http://review.coreboot.org/202
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
This change is warning and whitespace fixes in the
northbridge code for AMD Family 14 rev C0 cpu update.
This does not address warnings in the mainboard,
Agesa, Cimx, or southbridge code.
Change-Id: I7ee7018a292ebb2343c9b7986dd21227185879dc
Signed-off-by: Frank Vibrans <frank.vibrans@amd.com>
Signed-off-by: efdesign98 <efdesign98@gmail.com>
Reviewed-on: http://review.coreboot.org/134
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
Cosmetic only; replaces some 'while' loops with 'do; while' loops to
avoid repetition.
Replacement performed by the Ruby expression:
t.gsub!(/^(\s*)([^\n\{]+)\n\1(while[^\n\{;]+)\n\s*\2/,
"\\1do \\2\n\\1\\3;")
Change-Id: Ie0a4fa622df881edeaab08f59bb888a903b864fd
Signed-off-by: Noe Rubinstein <nrubinstein@proformatique.com>
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/183
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
It would be nicer to unify the code so that it does all detection at runtime
instead of compile time (but that would also significantly increase code size)
so if someone else wants to give it a shot...
Change-Id: Idc67bdf7a6ff2b78dc8fc67a0da5ae7a4c0a3bf0
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/184
Tested-by: build bot (Jenkins)
This change adds the southbridge related code to support
the update of the AMD Family14 cpus to the rec C0 level.
Some of the changes reside in mainboard folders but they
reference changed files in the southbridge folder so they
are included herein.
Change-Id: Ib7786f9f697eaf0bf8abd9140c4dd0c42927ec7e
Signed-off-by: Frank Vibrans <frank.vibrans@amd.com>
Signed-off-by: efdesign98 <efdesign98@gmail.com>
Signed-off-by: Kerry She <kerry.she@amd.com>
Signed-off-by: Kerry She <shekairui@gmail.com>
Reviewed-on: http://review.coreboot.org/135
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Adds support for initializing registered SDRAM modules on
Intel 440BX northbridge.
Drops unneeded romcc-inspired programming tricks.
Only set nbxecc flags (see 440BX datasheet, page 3-16) when
a non-ECC module has been detected in a row via SPD; also
drops an unneeded intermediate variable used in setting them.
Boot tested on ASUS P2B-LS with regular and registered ECC
SDRAM under Linux and memtest86+.
Change-Id: Idc99d49567cca55f819d6b0e98952b1c3256498a
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: http://review.coreboot.org/128
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This updates the code for the AMD SR5650 and SB700 southbridges.
Among other things, it changes the romstage.c files by replacing a
.C file include with a pair of .H file includes. The .C file is
now added to the romstage in the SB700 or SR5650 Makefile.inc.
file to the romstage and ramstage elements. This particular change
affects all mainboards that use the SB700, and their changes are
include herein. These mainboards are:
Advansus a785e,
AMD Mahogany, Mahogany-fam10, Tilapia-fam10,
Asrock 939a785gmh,
Asus m4a78-em, m4a785-m,
Gigabyte ma785gm,
Iei Kino-780am2-fam10
Jetway pa78vm5
Supermicro h8scm_fam10
The nuvoton/wpcm450 earlysetup interface is changed because the file
is no longer included in the mainboard romstage.c files.
Change-Id: I502c0b95a7b9e7bb5dd81d03902bbc2143257e33
Signed-off-by: Frank Vibrans <frank.vibrans@amd.com>
Signed-off-by: efdesign98 <efdesign98@gmail.com>
Reviewed-on: http://review.coreboot.org/107
Tested-by: build bot (Jenkins)
Reviewed-by: Kerry She <shekairui@gmail.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
This change adds the AMD Family 10 cpu support to the northbridge
folder. The northbridge/amd/agesa Kconfig and Makefile.inc are
changed as well.
Change-Id: Id76e9fa388c79ac469a673aaedaa4f1bfd7619d9
Signed-off-by: Frank Vibrans <frank.vibrans@amd.com>
Signed-off-by: efdesign98 <efdesign98@gmail.com>
Reviewed-on: http://review.coreboot.org/98
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
On installing/starting Windows (tested with Win7 Ultimate)
the system crashes with a Blue Screen of Death, reporting an ACPI BIOS error.
From Scott Duplichan:
To avoid the Windows BSOD, the uninitialized value TOM1 in the SSDT
must be corrected. The attached patch does this. It uses the older
patching method, and not the (possibly preferred) AML generation
method. To simplify the patching operation, I moved the AML item
'TOM1' to the start of the SSDT. The patch also includes code to
confirm the AML variable TOM1 is at the expected offset before patching.
Also tested & working with Linux.
Change-Id: I59cedc366e09d98f690b093d6a21fc0c864559c3
Signed-off-by: Scott Duplichan <scott@notabs.org>
Acked-by: Marshall Buschman <mbuschman@lucidmachines.com>
Reviewed-on: http://review.coreboot.org/91
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
Applying Scott Duplichan's fix for memory >=4GB
Adjusted it to the new directory structure (agesa_wrapper was renamed to
just agesa).
Boot-tested and confirmed to work, on my board Linux can now access the
whole RAM.
Change-Id: I31d66a488a7811d214d84653860b3e0116f67d19
Signed-off-by: Scott Duplichan <scott@notabs.org>
Acked-by: Marshall Buschman <mbuschman@lucidmachines.com>
Signed-off-by: Cristian Măgherușan-Stanciu <cristi.magherusan@gmail.com>
Reviewed-on: http://review.coreboot.org/48
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
for the transmit clock driving control. Unfortunately this is not enough
to make the HT1000 work reliably, therefore blacklist this for now in CPU
HT code. If ever anyone figure out what is wrong, it could be removed. The
downgrading now makes the board work on HT800, which is certainly better than
not at all with a HT1000 CPU.
Change-Id: I949bfd9b0b48ee12bd0234c2fb1deaaa773bd235
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Reviewed-on: http://review.coreboot.org/68
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This change adds the wrapper code for the AMD Family12
cpus and the AMD Hudson-2 (SB900) southbridge to the cpu,
northbridge and southbridge folders respectively.
Change-Id: I22b6efe0017d0af03eaa36a1db1615e5f38da06c
Signed-off-by: Frank Vibrans <frank.vibrans@amd.com>
Signed-off-by: efdesign98 <efdesign98@gmail.com>
Reviewed-on: http://review.coreboot.org/53
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This change moves the AMD Family14 cpu Agesa code to
the vendorcode/amd/agesa/f14 folder to complete the
transition to the family oriented folder structure.
Change-Id: I211e80ee04574cc713f38b4cc1b767dbb2bfaa59
Signed-off-by: Frank Vibrans <frank.vibrans@amd.com>
Signed-off-by: efdesign98 <efdesign98@gmail.com>
Reviewed-on: http://review.coreboot.org/52
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
This change renames the cpu/amd/agesa_wrapper, northbridge/
amd/agesa_wrapper, and southbridge/amd/cimx_wrapper folders
to {cpu|NB}/amd/agesa and {SB}/amd/agesa to shorten and
simplify the folder names.
There is also a fix to vendorcode/amd/agesa/lib/amdlib.c to
append "ull" to a trio of 64-bit hexadecimal constants to
allow abuild to run successfully.
Change-Id: I2455e0afb0361ad2e11da2b869ffacbd552cb715
Signed-off-by: Frank Vibrans <frank.vibrans@amd.com>
Signed-off-by: efdesign98 <efdesign98@gmail.com>
Reviewed-on: http://review.coreboot.org/51
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
We're using '0xcafed00d' all over the code as magic for ACPI S3
resume. Let's add a define for that. Also replace 0xcafebabe by
a define.
Change-Id: I5f5dc09561679d19f98771c4f81830a50202c69f
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/33
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Signed-off-by: Marc Jones <marcj303@gmail.com>
Acked-by: Scott Duplichan <scott@notabs.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6619 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Scott Duplichan <scott@notabs.org>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6594 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2) Correct UMA graphics PCI device ID.
Signed-off-by: Scott Duplichan <scott@notabs.org>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6593 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Scott Duplichan <scott@notabs.org>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6581 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Scott Duplichan <scott@notabs.org>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6578 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Stefan switched away from #ifdef across the tree (and is absolutely right with that), but
unfortunately there are some special cases that trigger in even more special situations.
Revert one such change selectively. It's destined to go once CMOS is reworked.
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6566 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Simplify
read_option(CMOS_VSTART_foo, CMOS_VLEN_foo, somedefault)
to
read_option(foo, somedefault)
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6565 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Comment by Peter,
The variable name "temp" unfortunately does not explain what the value
is. The commit message also does not have hints. Hopefully in the
future it's possible to also use a brief moment to improve the clarity
of the code, while it is already being fixed for some other
reason. Ie. fixing up variable names, writing particularly informative
commit messages, or of course both at the same time! :)
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6517 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The current version doesn't honor TSEG, and fails to
report the correct top of RAM if IGD is disabled. This
is because it uses the BSM (base of stolen RAM) register.
In that case, we should use the TOLUD register.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Acked-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6483 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
It is based on other existing Fam10 code.
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6464 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The patch makes these changes:
1) Remove the BUID swap list from ht_wrapper.c and put it in each of 15
romstage.c files where it is used (AMD family 10h projects).
2) Add a prototype to amdfam10.h.
3) Modify the swap list and test in real hardware for mahogany_fam10 and
kino family 10h and confirm HT3 operation for the SB link.
Abuild tested.
Signed-off-by: Scott Duplichan <sc...@notabs.org>
Acked-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6439 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Acked-by: Patrick Georgi <patrick.georgi@secunet.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6418 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode.
I don't understand what this was doing nor find docs for these regs
Maybe it was left over from some copy & paste ?
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6410 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode.
In fact I changed coreDelay before deleting
the code in fidvid that called it. But there're
still a couple of calls from src/northbridge/amd/amdmct/wrappers/mcti_d.c
Since the comment encouraged fixing something, I
parametrized it with the delay time in microseconds
and paranoically tried to avoid an overflow at pathological
moments.
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6408 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode.
bits 13 - 15 of F3xd4 (StutterScrubEn, CacheFlushImmOnAllHalt and MTC1eEn
are reserved for revisions D0 and earlier, so whe should not set them
to 0 in fidvid.c config_clk_power_ctrl_reg0(...), called from prep_fid_change.
For revisions > D0 (when we support them) it is ok not ot clear them,
because they are documented as 0 on reset. bit 12 should be left alone
according to BKDG. Should I set 11:8 ClkRampHystSel to 0 in the mask
too, just to indicate we're touching them ? We'll OR them to 1111 anyway...
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6407 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode.
Well, I understand it better like this, but maybe
it's only me, part of the changes are paranoic, and
the only effective change is for a factor depending on
mobile or not that I can't test.
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6406 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode.
Add an untested step in BKDG 2.4.2.8. I don't
have the hardware with Core Performance Boost and
I think it's only available in revision E that does
not even have a constant yet.
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6405 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode.
Add to init_fidvid_stage2 some step
mentioned in BKDG 2.4.2.7 that was missing . Some lines
are dead code now, but may handy if one day we support
revison E CPUs.
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6404 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode.
Add to init_fidvid_stage2 some step for my CPU (rev C3)
mentioned in BKDG 2.4.2.6 (5) that was missing
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6403 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode.
Looking at BKDG the process for updating
Pstate Nb vid after warn reset seemed
more similar to the codethat was there fo
pvi than the one for svi, so I called the
pvi function passing a pvi/svi flag. I don't
find documentation on why should UpdateSinglePlaneNbVid()
be called in PVI, but since I can't test it,
I leave it as it was.
This patch showed some progress beyond fidvid in my
boar,d but only sometimes, most times it just didn't
work.
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6402 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode.
Factor out some common expressions.
Add an error message when coreboots hangs waiting for a pstate
that never comes (it happened to me), and throw some
paranoia at it for good mesure.
If I understood BKDG fam10 CPUs never need a software initiated vid transition,
because the hardware knows what to do when you just request
a Pstate change if the cpu is properly configured. In fact
unifying a little what PVI and SVI do was better for my board (SVI).
So I drop transitionVid, which I didn't understand either (why
did it have a case for PVI if it is never called for PVI ?
Why did the PVI case distinguigh cpu or nb when PVI is
theoretically single voltage plane ? ).
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6401 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode.
Contemplate the possibility of nbCofVidUpdate not being
defined, trying to get closer to BKDG
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6399 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode.
BKDG says nbSynPtrAdj may also be 6 sometimes.
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6397 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode.
I didn't understand quite why it did that iwth F3xA0 (Power
Control Misc Register) so I moved Pll Lock time to rules in defaults.h
and reimplemented F3xA0 programming. A later patch will remove
a part I don't know what's mean to do.
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6396 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CPU and northbridge frequency and voltage
handling for Fam 10 in SVI mode.
Bring F3xD4 (Clock/Power Control Register 0) more in line
with BKDG i more cases. It requires looking at the CPU package type
so I add a function for that (in the wrong place?) and some
new constants
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6395 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This affects the CMOS options iommu, ECC_memory, max_mem_clock,
hw_scrubber, interleave_chip_selects.
If they're absent in cmos.layout, a Kconfig value is used if it exists,
or a hardcoded default otherwise.
[Patrick: I changed the ramstage CMOS handling a bit, and dropped the
reliance of hw_scrubber on ECC RAM, as it has nothing to do with it -
it's the cache that's being scrubbed here.]
Signed-off-by: Josef Kellermann <seppk@arcor.de>
Acked-by: Patrick Georgi <patrick.georgi@secunet.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6380 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The current code works only with dual channel if Channel 0 uses SPD address
0x50/0x51, while the second channel has to use 0x52/0x53.
For hardware that uses other addresses (like the ThinkPad X60) this means we
get only one module running instead of both.
This patch adds a second parameter to sdram_initialize, which is an array with
2 * DIMM_SOCKETS members. It should contain the SPD addresses for every single
DIMM socket. If NULL is given as the second parameter, the code uses the old
addressing scheme.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6374 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Frank Vibrans <frank.vibrans@amd.com>
Acked-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6345 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Workaround for 131 removed.
Changed workaround for erratum 110 to only include pre-revision-F
processors.
For details, check AMD publications:
#25759 (Errata for Fam F pre-revision F processors)
#33610 (Errata for Fam F revision F and later processor)
Based on work and previous patches by:
Rudolf Marek <r.marek@assembler.cz>
Josef Kellermann <seppk@arcor.de>
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Acked-by: Patrick Georgi <patrick.georgi@secunet.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6340 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
smm-y wasn't required before, because udelay.c used to be #included from
various files in src/mainboard.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Patrick Georgi <patrick.georgi@secunet.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6303 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
After this patch, tilapia can run in higher memory frequency.
To test the high frequency, dont forget to change the freq limit in
mcti_d.c:
static void mctGet_MaxLoadFreq(struct DCTStatStruc *pDCTstat)
{
pDCTstat->PresetmaxFreq = 800;
}
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6276 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
done. Please send the testing report.
Note: The pDCTstat->PresetmaxFreq in mctGet_MaxLoadFreq() should be set
to a higher limit, otherwise the frequnce will be set as 400MHz.
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Acked-by: Scott Duplichan <scott@notabs.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6258 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
to FG (FooGlue). As the GX2 has no VIP port.
-Change the Memmory setup MSR register names so they correspond better to the
databook. (Part1)
This is less confusing for beginners.
-Add a MSR printing function to northbridge.c like in the Geode LX code.
-Remove the AES register names.(GX2 has no AES registers)
-Delete some unused code.
-Clean up GX2 northbridge code to match Geode LX code.
-Add missing copyright header to northbridge.c.
-Move hardcoded IRQ defining from northbridge.c to irq_tables.c .
Signed-off-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6221 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
and drop some romcc relics in 440bx code too
Signed-off-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6218 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Most boards unconditionally call this. Fix it in header file instead of each single romstage.c
Signed-off-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6216 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The intel/xe7501devkit is still broken, I think the (romcc) image is too big to
fit in the bootblock if CONFIG_DEBUG_RAM_SETUP is enabled. It would make sense
to convert all CPU_INTEL_SOCKET_MPGA604 to CAR, but I have no hardware to test.
Signed-off-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6215 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6211 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6210 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6209 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6208 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
It's a good thing to use printk() instead of print_*() anyway
on 440BX (and other chipsets which have been converted to CAR).
Build tested and boot-tested on ASUS P2B-LS.
Signed-off-by: Keith Hui <buurin@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6206 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Hence drop the FALLBACK_ prefix
Signed-off-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6204 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Don't include cmc.bin to the build. It's required, but we don't ship it
- mptable's API changes a bit. Adapt.
- Fix ACPI for new iasl versions with improved code validation
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6199 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
which uses it.
Compiles, but not boot tested lately.
Many things missing (eg. SMM support, proper ACPI, ...)
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6198 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
coreboot made it kind of complicated to print a character on serial. Not quite
as complicated as UEFI, but too much for a good design. Fix it.
Signed-off-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6191 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The patch looks at certain DDR configurations (dual rank/single rank) and lowers the clocks to 2T or frequency as guide suggest. It sets the DualDIMMen bit which I believe should be set for non-dual channel configs.
The patch does not implement support for three dimm configurations supported from revE.
On the other hand it should improve greatly memory stability across the 939 platform.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6176 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The writes to NVRAM are not used in asrock board (k8 pre rev f) but they should work when used with am2 boards. In fact maybe the suspend will work on mahogany or others ;) - with some simple patch which follows for asrock.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6173 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
The patch is based on my 2008 patch.
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6172 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Abuild tested. Please check all changes if I did not make any wrong while converting this to bytes.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6171 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
src/arch/x86.
Signed-off-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6161 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
the prefix was introduced in the early v2 tree many years ago
because our old build system "newconfig" could not handle two files with
the same name in different paths like /path/to/usb.c and
/another/path/to/usb.c correctly. Only one of the files would end up
being compiled into the final image.
Since Kconfig (actually since shortly before we switched to Kconfig) we
don't suffer from that problem anymore. So we could drop the sb700_
prefix from all those filenames (or, the <componentname>_ prefix in general)
- makes it easier to fork off a new chipset
- makes it easier to diff against other chipsets
- storing redundant information in filenames seems wrong
Signed-off-by: <stepan@coresystems.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6150 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The read-modify-write wasn't needed. This is easier to understand.
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6136 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
I cleaned up the patch and moved most of the dsdt.dsl and
acpi_tables.c into the southbrige/northbridge directory.
Updated patch should fix abuild error and incorporates suggestions
on irc by uwe (thanks for the comments).
Thanks to Idwer Vollering <vidwer@gmail.com> for the original patch.
Tested:
Linux (poweroff, powerbutton event)
XP (poweroff, powerbutton event)
Abuild-tested
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6127 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2) the patch implements get_cbmem_toc in chipset specific way if defined.
On Intel targets it should be unchanged. On K8T890 the the cbmem_toc is read from NVRAM. Why you ask? Because we cannot do it as on intel, because the framebuffer might be there making it hard to look for it in memory (and remember we need it so early that everying is uncached)
3) The patch removes hardcoded limits for suspend/resume save area (it was 1MB) on intel. Now it computes right numbers itself.
4) it impelements saving the memory during CAR to reserved range in sane way. First the sysinfo area (CAR data) is copied, then the rest after car is disabled (cached copy is used). I changed bit also the the copy of CAR area is now done uncached for target which I feel is more right.
I think I did not change the Intel suspend/resume behaviour but best would be if someone can test it. Please note this patch was unfinished on my drive since ages and it would be very nice to get it in to prevent bit rotten it again.
Now I feel it is done good way and should not break anything. I did a test with abuild and it seems fine.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6117 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This needlessly complicates the code and increases register pressure on romcc
chipsets. We did the same conversion on i440BX, i830, and others.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6112 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
initializing VGA happens pretty much as the last thing before starting the
payload. Hence, drop VGA console support, as we did in coreboot v3.
- Drop VGA and BTEXT console support.
Console is meant to be debugging only, and by the time graphics comes up
99% of the risky stuff has already happened. Note: This patch does not remove
hardware init but only the actual output functionality.
The ragexl driver needs some extra love, but that's for another day
- factor out die() and post()
- drop some leftover RAMBASE < 0x100000 checks.
Signed-off-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: QingPei Wang<wangqingpei@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6111 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also, remove some less useful comments, some dead code / unused functions.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6108 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also drop some dead or useless code snippets.
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6107 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- VIA VT8235: Do the shift in smbus_read_byte() as all other chipsets do.
- spd.h: Move RC00-RC63 #defines here, they were duplicated in lots of
romstage.c files and lots of spd_addr.h files. Don't even bother for
those spd_addr.h which aren't even actually used, drop them right away.
- Replace various 0x50 hardcoded numbers with DIMM0, 0x51 with DIMM1,
and 0xa0 with (DIMM0 << 1) where appropriate.
- Various debug.c files: Replace SMBUS_MEM_DEVICE_START with DIMM0,
SMBUS_MEM_DEVICE_END with DIMM7, and drop useless SMBUS_MEM_DEVICE_INC.
- VIA VX800: Drop unused SMBUS_ADDR_CH* #defines.
- VIA VT8623: Do the shift in smbus_read_byte() as all other chipsets do.
Then, replace 0xa0 (which now becomes 0x50) with DIMM0.
- alix1c/romstage.c, alix2d/romstage.c: Adapt to recent bit shift changes.
- Various files: Drop DIMM_SPD_BASE and/or replace it with DIMM0.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6100 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
addressing scheme to match the rest of the tree
(0x50 instead of 0xa0).
abuild tested.
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6099 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- s/Options.lb/devicetree.cb/
- s/Config.lb/devicetree.cb/
- s/cache_as_ram_auto.c/romstage.c/
- h8dmr_fam10/README: Drop obsolete comment, we have mc_patch_01000086.h in
the tree now.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6095 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6089 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
http://tracker.coreboot.org/trac/coreboot/changeset/3953
Note that all corresponding DSDTs only ever check TOM2 against 0.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6082 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6074 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
-- When building for UMA, reduce the limit for DRAM below 4GB
from E0000000 to C0000000. This is needed to accomodate the
UMA frame buffer.
-- Correct problem where msr C0010010 bits 21 and 22 (MtrrTom2En
and Tom2ForceMemTypeWB) are not set consistently across cores.
-- Enable TOM2 only if DRAM is present above 4GB.
-- Use AMD Tom2ForceMemTypeWB feature to avoid the need for
variable MTRR ranges above 4GB.
-- Add above4gb flag argument to function x86_setup_var_mtrrs. Clearing
this flag causes x86_setup_var_mtrrs() to omit MTRR ranges for
DRAM above 4GB. AMD systems use this option to conserve MTRRs.
-- Northbridge.c change to deduct UMA memory from DRAM size reported
by ram_resource. This corrects a problem where mtrr.c generates an
unexpected variable MTRR range.
-- Correct problem causing build failure when CONFIG_GFXUMA=1 and
CONFIG_VAR_MTRR_HOLE=0.
-- Reserve the UMA DRAM range for AMD K8 as is already done for AMD
family 10h.
Tested with mahogany on ECS A780G-GM with 2GB and 4GB.
Tested with mahogany_fam10 on ECS A780G-GM with 2GB and 4GB.
Signed-off-by: Scott Duplichan <scott@notabs.org>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6067 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The function is called with no format specifiers in the first parameter
throughout the code, so it needs to work also with just one parameter.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6056 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6036 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This is Abuild and boot tested.
Signed-off-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6023 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Drop banner(), use printk()s instead.
- Uncomment a few printk()s, if a users doesn't want to see them he/she
can lower the debug level.
- Replace print_emerg() with printk(BIOS_EMERG) etc.
Also change 'Assymetirc' into 'Asymmetric', thanks to Idwer for spotting.
This is Abuild and boot tested.
Signed-off-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6021 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This is Abuild and boot tested.
Signed-off-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6016 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
and gx2/raminit.c.
This is Abuild and boot tested.
Signed-off-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6014 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also, change the GX2 boards to use it.
Add a processor speed setting function in human readable MHz and remove
the useless and broken PLLMSR settings (the processor speed was hardcoded
to 366MHz in pll_reset.c).
Signed-off-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6011 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also, add a copyright header to pll_reset.c.
Signed-off-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6009 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also, make them all fit in 80chars/column, fix some whitespace issues
and also some typos I noticed.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5993 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
is sometimes logged. The reason is that the AP first sets a completion value
such as 0x13, which is what function wait_cpu_state() is waiting for. Then a
short time later, the AP calls function init_fidvid_ap(). This function sets
a completion value of 01. When logging is off, wait_cpu_state is fast enough
to see the initial completion value for each of the APs. But with logging
enabled, one or more APs may go on to complete function init_fidvid_ap, which
sets the completion value to 01. While mostly harmless, the timeout does
increase boot time. This patch eliminates the timeout by making function
wait_cpu_state recognize 01 as an additional valid AP completion value.
Signed-off-by: Scott Duplichan <scott@notabs.org>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5966 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This is pretty much the same mechanism as in r5929.
- Use 'romstage-y' to turn i82801ax_early_smbus.c and i82801bx_early_smbus.c
into distinct compilation units, and don't #include the files anymore
in romstage.c files.
- Ditto for northbridge/intel/i82810/raminit.c, and
northbridge/intel/i82810/debug.c.
- Add various header files which are now needed, drop unused includes.
- Make functions that need to be visible non-static.
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5951 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Drop "select ROMCC" from the boards, as well as early_mtrr stuff.
- Add "select CACHE_AS_RAM" to socket_PGA370/Kconfig, as well as the
usual DCACHE_RAM_BASE and DCACHE_RAM_SIZE variables.
- In socket_PGA370/Makefile.inc add:
cpu_incs += $(src)/cpu/intel/car/cache_as_ram.inc
- Other smaller related fixes.
Abuild-tested and boot-tested on MSI MS-6178.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5949 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This is in preparation of further i810 fixes and switching it to CAR.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5944 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
As both ioapic.h and acpi.h define a macro named "NMI", rename one
of them (NMI -> NMIType in acpi.h).
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5943 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The following functions are moved to devices/device_util.c:
- ram_resource()
- tolm_test()
- find_pci_tolm()
There are only two tolm_test() / find_pci_tolm() which differ from the
defaults, one of them can easily be eliminated in a follow-up patch,
maybe even both, but for now keep it simple and only eliminate the majority.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5937 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Use 'romstage-y' to turn i82371eb_early_pm.c and i82371eb_early_smbus.c
into distinct compilation units, and don't #include the files anymore
in romstage.c files.
- Ditto for lib/debug.c, northbridge/intel/i440bx/raminit.c, and
northbridge/intel/i440bx/debug.c.
- Add various header files which are now needed.
- Make functions that need to be visible non-static.
- Drop a remaining "select ROMCC" from a 4440BX board.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Idwer Vollering <vidwer@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5929 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Add "select CACHE_AS_RAM" in src/cpu/intel/slot_1/Kconfig.
- Add the following in src/cpu/intel/slot_1/Makefile.inc:
cpu_incs += $(src)/cpu/intel/car/cache_as_ram.inc
- Remove "select ROMCC" from all 440BX board Kconfig files.
- Drop all early_mtrr_init() calls, that's done by CAR code now.
Various small fixes were needed to make it build:
- Drop do_smbus_recv_byte(), do_smbus_send_byte(), do_smbus_write_byte(),
those were never called anyways.
- Remove the "static" from the main() functions in romstage.c files.
- Always call dump_spd_registers() from the 440BX debug.c, but use
"#if CONFIG_DEBUG_RAM_SETUP" to only have that code if RAM debugging
is enabled in menuconfig.
- Drop all "lib/ramtest.c" #includes and ram_check() calls (even if
commented out) from romstage.c's, as we've done for most other boards.
- Add missing #includes or prototypes. Some of the prototypes will be
removed later when we get rid of the #include'd .c files.
Abuild-tested for all boards, and boot-tested on A-Trend ATC-6220.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5917 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Remove many more .c-includes from i945 based boards.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5910 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
rename it slightly, make it visible only on relevant northbridges,
drop it entirely from via boards (as they seem to have picked it
up from AMD code without using it themselves), and make it
default to false for all boards.
Some romstages used to set this to "true" (ie. "print debug output"),
but I didn't follow up on it in Kconfig - if you need it to debug CAR,
enable it yourself.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5898 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This is needed for Gentoo gcc-4.1.2 to build the i945 code. A warning is
thrown because the comparison in the last hunk is between u16 and -1 and
can never be true.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5895 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Both chipsets use the src/northbridge/intel/i945 code but that code
needs to know which chipset is actually used. Having separate
NORTHBRIDGE_ options allows the I945GC/I945GM choice to be removed
since code can test the NORTHBRIDGE_ option directly.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5893 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5891 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
at the same time let the user specify sources instead
of object files:
- objs becomes ramstage-srcs
- initobjs becomes romstage-srcs
- driver becomes driver-srcs
- smmobj becomes smm-srcs
The user servicable parts are named accordingly:
ramstage-y, romstage-y, driver-y, smm-y
Also, the object file names are properly renamed now, using
.ramstage.o, .romstage.o, .driver.o, .smm.o suffixes consistently.
Remove stubbed out via/epia-m700 dsdt/ssdt files - they didn't
easily fit in the build system and aren't useful anyway.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coreystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5886 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5846 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Some boards still used the old DEBUG_RAM_SETUP (without _CONFIG prefix).
Also, consistently use "#if CONFIG_DEBUG_RAM_SETUP" (not #ifdef) as we do
elsewhere.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5843 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
statement to those files that actually need it. This significantly
reduces the number of dependencies, so it's no longer extremely ugly to
specify them manually (see the src/pc80/Makefile.inc portion)
- Add double include guards around option_table.h defines
- Also, drop the AMD DBM690T work around for the issue
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5838 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5821 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Resolves a number of TODOs items within, and clarified a number of other TODOs.
Change register_values[] from long to u8 (byte). For what we are doing
this is sufficient and makes it only 1/4 the size.
Remove a hard-coding of SDRAMC register that is redundant and now
incorrect, now that SDRAMC is conditioned on SDRAMPWR_4DIMM Kconfig
and set through register_values[].
This fixes all boards with 3 DIMM slots (e.g. ASUS P2B, A-Trend ATC-6220).
RPS registers are now set in runtime code; remove it from
register_values[] table.
Bring DUMPNORTH() back. The code it refers to is still there.
Move #define of NB up so the DUMPNORTH() macro can use it.
Signed-off-by: Keith Hui <buurin@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5820 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
fixes a few alignment wrinkles and sets up and registers the MMCONF area
for AMD Fam10h CPUs (where selected by mainboard configuration). It
removes a bit of code that proved troublesome in MMCONF setups from
mcp55_early_setup_car.c, as per earlier discussion.
Signed-off-by: Arne Georg Gleditsch <arne.gleditsch@numascale.com>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5796 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Fix a typo, too.
Signed-off-by: Arne Georg Gleditsch <arne.gleditsch@numscale.com>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5792 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
to using ram, so something like the appended is perhaps more
appropriate. Confirmed to work on hw.
Signed-off-by: Arne Georg Gleditsch <arne.gleditsch@numscale.com>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5791 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
platform specific value. Before that, we can set it manually if the boards
need to run in a higher frequency, which has been tested on Tilapia.
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Acked-by: Zheng Bao <zheng.bao@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5777 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Kerry She <Kerry.she@amd.com>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5776 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
be used in write levelization training.
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5758 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- HAVE_HIGH_TABLES
- HAVE_LOW_TABLES
- FALLBACK_SIZE
Jens Rottmann sent an almost identical patch at the same time, so
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTEmbedded.de>
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5745 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
chipset support it. But this involves a long list of 'depends', which you have
to remember updating manually. Converted this into HAVE_... properties, which
will be inherited automatically if someone copies a chipset to create a new
one.
Signed-off-by: Jens Rottmann <JRottmann@LiPPERTEmbedded.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5743 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Odd. The others don't.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5742 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- prevent GCC from inlining do_ram_command - it will break RAM initialization.
- fix the PCIRST# mechanism in those boards that do it, it requires 200ms, not
200us
- move PCIRST# as early as possible (before ich7_enable_lpc)
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5740 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
* DRAM initialization done message is now printed in debug-mode only, rather than everytime.
Signed-off-by: Aurelien Guillaume <aurelien@iwi.me>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5739 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Revision Guide for AMD Family10h processors (#41322) rev 3.74 June 2010
with patch.erratum414 it stops here (next patches don't make it get further,
but they're needed according to documentation, don't break anything for me and
I still don't have a solution for booting, so I'm keeping them there in case
they fix something.
testx = 5a5a5a5a
Copying data from cache to RAM -- switching to use RAM as stack... Done
testx = 5a5a5a5a
Disabling cache as ram now
Clearing initial memory region: Done
Loading stage image.
Check CBFS header at fffffd2e
magic is 4f524243
Found CBFS header at fffffd2e
Check fallback/romstage
CBFS: follow chain: fff00000 + 38 + 15b41 + align -> fff15b80
Check fallback/coreboot_ram
Stage: loading fallback/coreboot_ram @ 0x200000 (1114112 bytes), entry @
0x20000
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5733 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Revision Guide for AMD Family10h processors (#41322) rev 3.74 June 2010
with this one it stops here or earlier (as soon as before the patch,
sometimes):
*** Yes, the copy/decompress is taking a while, FIXME!
v_esp=000cbf48
testx = 5a5a5a5a
Copying data from cache to RAM -- switching to use RAM as stack... Done
testx = 5a5a5a5a
Disabling cache as ram now
Clearing initial memory region:
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5732 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
While reviewing impact of this change it seems code for erratum 531 was not in
sync with current docs. I have checked uses of AMD_FAM10_ALL, but I
haven't looked up the docs for all of them, at first sight it seems ok
to include all FAM10 revisions in this mask.
Apply errata 531 only to revisions listed in Revision Guide for AMD Family10h
processors (#41322) rev 3.74 June 2010. Before it was applied also to
DR-B0, DA-C3 or HY-D0 which are not affected according to current docs.
Signed-off-by: Xavi Drudis Ferran <xdrudis@tinet.cat>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5729 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The bit 15 seems to be a new feature when CPU started to have more than 4
cores.
Zheng
Yes, this was add for revD.
Marc Jones
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5684 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
board porter: printk should always be available in CAR mode.
Also drop CONFIG_USE_INIT, it's only been selected on one ASROCK board
but it's not been used there. Very odd.
There is one usage of CONFIG_USE_INIT which was always off in
src/cpu/intel/car/cache_as_ram.inc and we have to figure out what to do with
those few lines.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5682 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Revert until someone with the boards refactors it.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5681 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
that causes CAR to hang, provide more debugging output wrt memory size,
and correct the numbering on the ram init sequence.
Signed-off-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5677 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Joseph Smith <joe@settoplinux.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5669 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Fix the ctrl_devport_conf_clear to clear the enable bit.
A simplification:
Dynamically enable ck804s that are found instead of relying on #defines.
Removing an Opteron changes the number of ck804s that are present.
Simple changes to make it easier to compare the factory BIOS with Coreboot when
using SerialICE for boards with the Nvidia ck804 chipset:
If the mask is zero, don't read the value, just write the new value over it.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5652 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Joseph Smith <joe@settoplinux.org>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5635 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
there is no free list.
Converting resource arrays to lists reduced the size of each device
struct from 1092 to 228 bytes.
Converting link arrays to lists reduced the size of each device struct
from 228 to 68 bytes.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5626 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5622 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
src/cpu/amd/model_fxx/model_fxx_update_microcode.c
src/northbridge/amd/amdk8/amdk8_acpi.c
src/southbridge/amd/amd8132/amd8132_bridge.c
Signed-off-by: Frank Vibrans <frank.vibrans@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
http://www.coreboot.org/pipermail/coreboot/2010-June/058668.html
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5607 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Joseph Smith <joe@settoplinux.org>
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Joseph Smith <joe@settoplinux.org>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5595 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
To apply this patch you need to
cp src/northbridge/amd/gx2/chipsetinit.c src/southbridge/amd/cs5535/
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Nils Jacobs <njacobs8@hetnet.nl>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5589 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Patrick Georgi