Signed-off-by: Joseph Smith <joe@smittys.pointclark.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3129 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
No functional changes, only cosmetics. This is compile-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3128 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
board.
This is done via the ec_init routine in a source file in the
mainboard/gigabyte/m57sli directory. A Config variable 'HAVE_FANCTL' has been
added to notify superio.c to get the ec_init externally.
I (Ward) have tested this on the PLCC and the SOIC/SPI version of this board.
It works.
Signed-off-by: Ronald Hoogenboom <hoogenboom30@zonnet.nl>
Acked-by: Ward Vandewege <ward@gnu.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3116 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Don't enable pin0 for ioapic of io-4.
1. apic error in kernel for MB with mcp55+io55
2. some pcie-cards could have pci bridge there, so need to put entries
for device under them in mptable.
Signed-off-by: Yinghai Lu <yinghailu@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3112 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Jonathan A. Kollasch <jakllsch@kollasch.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3111 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
device) and sets the chipset voltage from 1.6V to 1.5V.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3107 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
have GAME and MIDI portsenabled.
It has been tested with my board. It produces same results.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3105 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
following mainboard files had identical Geode LX specific print_conf()
implementations:
mainboard/amd/db800/mainboard.c
mainboard/amd/norwich/mainboard.c
mainboard/digitallogic/msm800sev/mainboard.c
mainboard/pcengines/alix1c/mainboard.c
Move print_conf() to northbridge/amd/lx/northbridge.c where it belongs.
Add a copyright notice to mainboard/digitallogic/msm800sev/mainboard.c.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Marc Jones <marc.jones@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3089 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
LPC device of the MCP55 southbridge, thus enabling flashrom access to the SPI
interface of the IT8716 SIO chip.
Changes :
1) - increase MAX_RESOURCES to 24 in device.h -> this was needed because some
functions of a PNP device can have more than 12 resources (ex the GPIO function
of IT8716f), in which case one could have an "array overflow" inside the device
structure (yes gcc is stupid!..) and ultimately a disaster (fool pointer at
device init time..)
2) - define resource masks for the GPIO function in
src/superio/ite/it8716f/superio.c -> this is needed because otherwise the IO
ranges which are set into the LPC bridge of the SB are very strange (f.ex.:
0x800->0x7ff and so on..). Problem: the PNP_IO0 resource is not defined for the
GPIO function, thus we have to define a "fake" mask "{0,0}" to avoid mismatching
by the init code
3) - enable the flash SPI interface into
src/mainboard/gigabyte/m57sli/Config.lb (by enabling the corresponding resource
into the GPIO function). I know that this is problematic because not all m57sli
boards are SPI, but .. do anyone have a better idea how to handle this?..
Signed-off-by: Florentin Demetrescu <echelon@free.fr>
I (Ward) have verified your patch on a rev2 of this board (it works!) as well
as on a rev1 (plcc). It does not affect flashing on rev1 nor have any averse
side effects that I noticed, so I think this patch should go in.
Acked-by: Ward Vandewege <ward@gnu.org>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3088 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
flashrom on the plcc-based rev 1 and 1.1 of the Gigabyte m57sli-s4 board.
Signed-off-by: Ward Vandewege <ward@gnu.org>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3087 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3085 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Tested on actual hardware by Sergei Antonov <saproj@gmail.com>.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Sergei Antonov <saproj@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3083 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
included on the CC line for cache_as_ram_auto.c
Tested on ubuntu, where formerly it failed.
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Ward Vandewege <ward@gnu.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3079 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Due to the automatic nature of this update, I am self-acking. It worked in
abuild.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3053 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
code is changed.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3052 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
suspend clock (undocumented in datasheet, documented in 'W83627HG-AW').
Introduce sio_init function for all this.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3049 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
similar smp_write_intsrc calls in preprocessor macros.
Also add some comments about the actual devices the INTs
belong to.
Signed-off-by: Torsten Duwe <duwe@lst.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3035 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
mainboard directories, but the code was not referenced anywhere.
intel/jarrell
dell/s1850
supermicro/x6dhr_ig2
supermicro/x6dhr_ig
supermicro/x6dhe_g2
supermicro/x6dhe_g
Besides that, the contents of these files were either duplicates of
src/cpu/intel/model_f3x/microcode_M1DF340E.h or
src/cpu/intel/model_f3x/microcode_M1DF3413.h.
svn remove the following files:
src/mainboard/supermicro/x6dhe_g/microcode_updates.c
src/mainboard/supermicro/x6dhe_g2/microcode_updates.c
src/mainboard/supermicro/x6dhr_ig/microcode_updates.c
src/mainboard/supermicro/x6dhr_ig2/microcode_updates.c
src/mainboard/dell/s1850/microcode_updates.c
src/mainboard/intel/jarrell/microcode_updates.c
Abuild tested, as expected no failures.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3028 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Bus 1, device 10 (function 0 only), routed to IO-APIC pin 18
(verified on an v1.0 board).
Signed-off-by: Torsten Duwe <duwe@lst.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3023 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Marc Jones <marc.jones@amd.com>
Reviewed-by: Jordan Crouse <jordan.crouse@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3016 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
this is needed (at the very least) to make FILO work on these boards.
Disable UDMA/33 per default, which is slower but the safe choice, as we
don't know which IDE devices a user has attached, and some don't support
UDMA/33 very well or at all.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3010 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Options.lb file that already had a "uses CONFIG_COMPRESSED_PAYLOAD_LZMA"
line in it.
I figure that only adding it to the files that already have support
for LZMA payloads makes sure I don't break anything.
Signed-off-by: Myles Watson <myles@pel.cs.byu.edu>
Acked-by: Ward Vandewege <ward@gnu.org>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3002 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
coherent_ht.c (save one empty line removed) so there's no use
to keep it around.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Marc Jones <marc.jones@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2998 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
according to mcqmcqmcq@fastmail.fm. Fix it.
Signed-off-by: Mondrian Nuessle <nuessle@uni-mannheim.de>
Acked-by: mcq <mcqmcqmcq@fastmail.fm>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2991 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
It never worked in v2 (the v1 port did work AFAIK, though), and it's
not really useful as reference for other boards anymore (as we now
have a dozen or so 440BX boards which work in v2).
This is a specialized, custom board (not sold on the "public market"),
so it's probably not useful for pretty much everyone out there anyway.
We can easily re-add it later (based on one of the other 440BX boards)
should there be interest and/or someone with the hardware to test.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2988 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2987 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
You cannot set 'default ROM_SIZE = 0' in Options.lb (and override it in
targets/*/Config.lb). While it'll work for manual builds, abuild doesn't
cope with that very well. So set a valid value in Options.lb, too.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2981 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
make it clearer why they are disabled (trivial).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2978 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Reason: The existing code does not tell us why it sets the watchdog
clock at all, but since it appears in cache_as_ram_auto.c instead of
the usual place (Config.lb) there has to be some meaning to it.
Simply do what the proprietary bios does: Use the external clock source.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Ward Vandewege <ward@gnu.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2973 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This enables us to have only one configuration and one set of code for
all revisions of the Gigabyte GA-M57SLI-S4.
Flash is now setup correctly for both SPI and LPC flash.
Detection of SPI flash in flashrom on rev. 2.x boards now hangs
instead of failing. However, that is just an effect of the combination
of incomplete initialization of the SPI controller and paranoid checks
in the flashrom SPI code.
If anyone wants to work on that, he needs a logic analyzer or creative
imagination. Hint: LPC-to-SPI read passthrough, clock signal.
Remaining issues for the M57SLI: Fan/environment control.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Harald Gutmann <harald.gutmann@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2972 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Upon incoming SMAF message from CPU (C3 or FID/VID change), the SB will
assert SLP# which is connected to LDTSTOP_L on K8 CPUs. Question is for how
long. Imho for 100us. Which is more than plenty (2us required) I will try
to justify this once I know what bios to set in SB.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2965 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
the other supported 440BX boards.
Fix up totally b0rked static device tree in Config.lb.
Drop useless and duplicated failover.c, use global one.
Make CPU init actually work (result: massive speed-up).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2960 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
With this patch, flashing the parallel EEPROM on board revisions 1.x
finally works. Flashing the serial EEPROM of board revisions 2.x is just
one patch away.
Torsten Duwe says:
Flash erase on my board was failing reliably. Now it works!
Andreas B. Mundt says:
For the first time I was able to write with flashrom and LB.
$flashrom -Vv --write linuxbios.rom
[...]
Vendor ID: GIGABYTE, part ID: m57sli
Found chipset "NVIDIA MCP55", enabling flash write... OK.
[...]
SST49LF040B found at physical address 0xfff80000.
Flash part is SST49LF040B (512 KB).
LinuxBIOS last image size (not ROM size) is 4096 bytes.
Manufacturer: GIGABYTE
Mainboard ID: m57sli
This firmware image matches this motherboard.
Programming page: 0007 at address: 0x00070000
Verifying flash... VERIFIED.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Torsten Duwe <duwe@lst.de>
Tested-by: Andreas B. Mundt <andi.mundt@web.de>
Tested-by: Torsten Duwe <duwe@lst.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2955 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
PIRQ table to make most devices work. Random small fixes (trivial).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2953 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Fix IRQ tables (Thanks to Marc Jones)
Fix IRQ SLOT #
Comment out ram test in early startup.
make the debug print in lx/raminit.c a debug print, not emerg print
Set the default console log level to 3, but leave in the possibility of
running with more info (leave maximum at 11)
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Marc Jones <marc.jones@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2952 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
(ICH/ICH0 up to the ICH9 family) in preparation for further
code improvements for the i82801xx southbridge code.
Small fixes in the 6300ESB PCI IDs.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2947 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
that board. Shift PCIe pin numbers downwards, and PCI int pins upwards.
This puts both PCI slots' int A and PCIe 16x int A into the right
position.
Signed-off-by: Torsten Duwe <duwe@lst.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2946 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Rudolf's suggestion making the symbol weak is elegant, but let's allow
some more discussion.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2944 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
have PCIe MMCONFIG.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2941 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
ICH5/ICH5R (more to follow) in preparation of further 82801xx improvements.
Use human-readable names for the PCI ID #defines.
Rename *_ISA to *_LPC as per datasheet.
The 82801DBM only has 3 (not 4) USB devices, looks like a copy-paste error.
The fixes in southbridge code are only to keep the build working for now,
any real improvements will only go into the 82801xx code in future.
This is abuild-tested so it shouldn't break anything.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2938 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2934 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2. Rename sisnb.c to sis761.c
3. Delete many mis-definition for sis device in
src/include/device/pci_ids.h
4. Trim trailing spaces for all files
Signed-off-by: Morgan Tsai <my_tsai@sis.com>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2931 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
> superiotool r2922
> Found Winbond W83627HF/F/HG/G (id=0x52, rev=0x0d) at 0x2e
Don't use the non-working trident driver for the blade3d (onboard vga
in the rom emulator has not been tested either)
It also adds some preliminary CAR support to the board, so it has a chance to
build again.
This board was broken since a couple of months, and the changes are minimal, so
I consider this a trivial change -- It doesn't change anything that was used,
obviously
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2926 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
self-acking before it gets lost.
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2924 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
http://www.linuxbios.org/pipermail/linuxbios/2007-October/025385.html ,
but change all apparantly related values that differ on my board with
legacy BIOS.
This makes both PCI cards appear, as well as the firewire device
TSB43AB23.
* PCI 01:07.0 appears fully functional
* PCI 01:08.0 (closer to the board edge) appears, but no interrupts
* PCI 01:0a.0 (FireWire) untested
Since none of these was even present without the patch I suggest to
apply it.
Signed-off-by: Torsten Duwe <duwe@lst.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Tested-by: Harald Gutmann <harald.gutmann@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2921 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
of all the other boards in this patch series.
Add missing PIRQ table to make most devices work.
Enable VGA support. Add flashrom flashing protection code.
Make CPU init actually work (result: massive speed-up).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2913 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
buildROM passes build flags through the CPU_OPT environment variable -
especially -fno-stack-protector for those of us lucky enough to have
Debian/Ubuntu. This adds to the cache_as_ram_auto.inc target
for the GA-2761GXDK so that the resulting cpu0.S is clean.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2911 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
southbridge now:
From: Morgan Tsai <my_tsai@sis.com>
It supports SiS761GX / SiS966 chipset, only for AMD K8 platform so far.
Due to integrated VGA sharing system memory, some code in southbridge
folder have to init northbridge.
Copyright (C) 2007 Morgan Tsai <my_tsai@sis.com>
Copyright (C) 2007 Silicon Integrated Systems Corp. (SiS)
Change Log:
Newly support GIGABYTE GA-2761GXDK
CPU type: AMD AM2 socket
Northbridge: SiS 761GX
Southbridge: SiS 966
SuperIO: ITE8716F
Signed-off-by: Morgan Tsai <my_tsai@sis.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2902 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Ethernet yet. The fixes are a board-specific fake spd_read_byte, cleaning up
comments, and just in general customizing for the 1c.
The lxraminit
change fixes a bug (&& used instead of ||), adds some debug prints which were
VERY useful debugging the alix1c, changes fatal error messages from print_debug
to print_emerg, and adds two functions:
banner, which just prints out a string with a banner, and
hcf, which print an emergency message and then pushes null bytes
into the uart forever, just to make sure that no bytes get lost
for any reason.
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2899 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This board uses nearly the same devices as the BCOM Winnet100, so most of
the new code here is from the BCOM Winnet100. They differ in the IRQ routing
table only.
BTW: The AXUS board uses standard DIMM memory and can be run at 100MHz SDRAM
clock speed (it runs reliably here since month).
Signed-off-by: Juergen Beisert <juergen@kreuzholzen.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2898 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Add missing entry for the NIC:
device pci 0f.0 on end # Ethernet (onboard)
- Drop the following lines:
register "com1" = "{115200}"
register "com2" = "{38400}"
Those entries hardcode the BAUD rate (as far as I can tell, please
correct me if I'm wrong). We don't want that -- instead the config option
TTYS0_BAUD in Options.lb should be used(?) I verified that dropping those
lines will not break serial output (COM1, 115200, 8n1).
- Enable IDE (PCI device 00:12.2) and add the following register lines
to tell the CS5530 code to actually enable IDE channel 0:
register "ide0_enable" = "1"
register "ide1_enable" = "0" # Not available/needed on this board
Tested with a 2.5" hard drive and FILO, works fine.
- Enable USB (PCI device 00:13.0), not sure why it was commented.
- Enable COM2 as it's used by the smartcard reader.
- Add CONFIG_COMPRESSED_PAYLOAD_LZMA to Options.lb, in order to fix
abuild for this board.
- Add some more comments.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2896 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
rodata.pci_driver" warnings are coming from? We were packing those
structures into a read-only segment, but forgot to mark them const.
Despite its size, this is a fairly trivial patch created by a simple
search/replace
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2891 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
assumes a 1MB rom chip.
Hence the default position for the VGA bios should also assume a 1MB rom chip,
not a 512KB chip.
Signed-off-by: Ward Vandewege <ward@gnu.org>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2887 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
since it is still our most wide-spread codebase.
The patch is pretty trivial, and nobody except Torsten even looked at
it in a week, so....
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2880 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This has not been working at all until now. With this fix, keyboard,
mouse, parallel port, and the Super I/O sensors work fine (tested
on actual hardware).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2867 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
replacing it with a minimal, but working, framework which will be expanded.
Drop a bunch of useless and duplicated files, add missing license headers.
I'm self-acking it this time, the diff is a huge unreadable mess and the old
code is broken anyway...
This code is tested to build fine, and can boot a Linux kernel up to a
login-prompt via FILO (IDE). This is verified on actual hardware.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2859 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
use that feature in order to not waste RAM.
Also, add missing CONFIG_VIDEO_MB for the eaglelion/5bcm, which should
fix the build for that board.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2848 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
currently don't have it but need it to compile with the new Geode GX1
VGA support. This sets the size at 4MB, which was the size previously
defined in the VGA code.
Signed-off-by: Corey Osgood <corey.osgod@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2845 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
See http://www.linuxbios.org/BCOM_WINNET100_Build_Tutorial for hardware
description and build tutorials.
Signed-off-by: Juergen Beisert <juergen@kreuzholzen.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2843 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
while I'm at it (trivial).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2839 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Hence the default position for the VGA bios should also assume a 1MB rom chip, instead of a 512KB chip.
Signed-off-by: Ward Vandewege <ward@gnu.org>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2792 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
(or at least most) mainboards. This should put and end to
copy-paste'ing the same file again and again for every mainboard.
Fix the build for the MSI MS-6178 target (wrong location of the common
failover.c file).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2772 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Removed reset.c and added copyright headers.
Remove debug.c. It is not used and should not be here.
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2766 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This is a geode LX board. There are timing settings that are not right
yet, we are still trying to get our board to boot Linux :-)
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2765 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Now uses CAR.
New code for SPD-less memory implementation.
Updated IRQ routing.
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2728 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
the system boot to a command line.
This patch comments out the code to set up the vga framebuffer to allow
the system to boot, without this fix the system hangs during elfboot.
The only line that is absolutely necessary to change is the SMRAM setup,
however I've commented out all vga setup to make it very obvious to both
the kernel/payload and anyone looking at the code that vga isn't
currently working. This setup might also be better handled in
northbridge.c, if it doesn't need to be done before ram init, yet
another reason to comment it all. In the future, LinuxBIOS needs to be
told that the graphics memory area, 1mb or 512kb (at the user or
developer's option), is reserved for the onchip vga, but I'm not sure if
it's taken at the top or bottom of the memory, yet. LB may also need to
set a base address for the AGP aperture and/or be told that range is
reserved as well, whether this was originally the job of the system bios
or vga bios is still a mystery. It also corrects the number of entries
in irq_tables.c, without this fix the kernel would probably complain and
hang due to unmapped IRQs.
Signed-off-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2725 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
more than just one way. This version should be (more) correct.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2723 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
southbridges, along with the Asus MEW-VM. With this, my machine attempts to
boot linux, but does so very slowly and fails during the boot process, probably
because of the irq tables.
Signed-off-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Joseph Smith <joe@smittys.pointclark.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2719 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The DB800 is the AMD LX Reference Design Kit platform.
For details see: http://www.amd.com/geodelxdb800
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2718 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Both are very similar, thus both use the JUKI-511P target.
Linux with patches from Juergen Beisert
(http://www.linuxbios.org/pipermail/linuxbios/2007-May/020932.html)
boots and work fine (ide, usb, ethernet, serial, keyboard and sound
work normally).
Problems:
- Filo loads a bzImage only from ide0 (ide1 doesn't work yet).
- Video doesn't work, yet.
Signed-off-by: Nikolay Petukhov <nikolay.petukhov@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2716 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Linux booted with the proprietary BIOS reports 2e.f as PS/2 mouse
in the output of 'lspnp -v'.
- The floppy on 2e.f was a typo, should have been 2e.e from the beginning.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2709 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Super I/O part was incorrect.
Also, add ide0_enable/ide1_enable variables, and enable both the
primary and secondary IDE interface per default.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2708 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Only check the RAM from 0 - 640 KB and 768 KB - 1 MB now. That's
available on all boards, regardless of what DIMMs you use.
Tested on the Tyan S1846, works fine.
- Properly set the PAM registers to allow the region from 768 KB - 1 MB
to be used as normal RAM (required for the above).
- Document all of this properly. Add/improve other documentation, too.
- Simplify and document code in northbridge.c.
- Cosmetics and coding style.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2701 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Marc Jones <marc.jones@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2687 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- the Transmeta TM5800 northbridge
- the Densitron DPX114 mainboard (the only one using the TM5800)
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2685 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
hardware, rather than always on at full speed. Set temperature treshold values
to safe defaults, rather than the not-so-safe power-on defaults.
Signed-off-by: Ward Vandewege <ward@gnu.org>
Acked-by: Yinghai Lu <yinghailu@gmail.com>
Acked-by: Ward Vandewege <ward@gnu.org>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2674 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
With CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2=0, 1 million outb():s are used
for timer calibration, which takes about one second.
All EPIA-M boards have timer2 so we use it to boot faster.
Only some EPIA boards have the Nehemiah CPU with timer2 so we default to IO
calibration but add the TSC options so that they can be set in Config.lb.
src/mainboard/via/epia*/reset.c is dead code (entire file within #if 0) so we
set HAVE_HARD_RESET=0 for both boards.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2659 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Acked-by: Stefan Reinauer <stepan@coresystems.de>
Signed-off-by: Marc Jones <marc.jones@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2652 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
problems with the asi/mb_5bmlp (trivial).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2644 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
minor changes, to bring them up to par. It also should remove (but might
just clean out) the irq_tables.c from both boards, because they were
just copied from Via Epia to begin with, and weren't usable. As far as I
can tell, these are the only changes needed to the targets for now,
aside from fixups to reset.c when the time comes. Both have been build
tested, but not checked on hardware since I don't have it. I have left
Uwe as the copyright holder since the only changes I've made are trivial.
Signed-off-by: Corey Osgood <corey_osgood@verizon.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2642 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
the IGEL Winnet III thin client.
It boots a Linux kernel, but there are some problems. The login
prompt is never reached, it simply hangs at some point.
One possible reason is the IRQ table, which needs fixing.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2641 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
the 5c register in the southbridge so that interrupts are routed
correctly.
With this patch, ethernet works quite well.
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2640 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
adds a symbol to the model_lx/cache_as_ram.inc, and modifies some
files in the mainboard directory. This patch has been tested but there
is a remaining problem which I am tracking down. Expect one more patch
to "get it all working".
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2638 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2636 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
I'm self-acking as this is pretty trivial. I tested both a normal build
and an abuild-run, and nothing breaks.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2635 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
broke and stopped FILO
from being able to boot.
The fix is a simple one line change plus a comment to
src/mainboard/via/epia/auto.c to write to the IDE
configuration register 0x42 . This has always been done here, however
at some point
something broke it.
The same register was also being set correctly in ide_init(), however
for some reason
this does not work. Possibly the register needs to be set before the IDE
peripheral is enabled
or maybe it is a timing issue.
The section of code in ide_init() (
src/southbridge/via/vt8231/vt8231_ide.c ) that does
write to register 0x42 has been commented out as it is superfluous
and I have added a comment to indicate the reason, should someone at a
future date wonder
why.
I have also changed the default COM speed from 19200 to 115200 in
src/mainboard/via/epia/Options.lb
There has been mention before about the EPIA board not being able to use
115200 but I have seen
no such problems with my board.
Signed-off-by: Ben Hewson <ben@hewson-venieri.com>
This patch worked for me and allowed me to boot Debian kernel
2.5.16-4-486 on an epia 800 mhz system. It is able to consistently get
through the initialization and start init now.
However, after that it crashes at various points in the boot process.
Acked-by: Alex Mauer <hawke@hawkesnest.net>
Note from comitter: I am commiting this, although:
1. it's not the exact right way to fix it up, the chip.h for the sb
should change
2. Alex reports problems, which are almost certainly memory issues.
But it is as close as we've gotten. I can't test it.
Ron Minnich
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2633 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Geode changes.
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2632 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
based on the Geode LX processor. The Norwich is the canonical
Geode reference, and will server as a good basis for other
Geode based platforms.
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2629 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
as that is not RAM but used for other stuff.
First try at PCI init added to src/mainboard/tyan/s1846/Config.lb.
Use a real payload (FILO) per default now.
Note: this cannot boot a payload, yet, but it gets a lot further now.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2623 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Comment out code which currently doesn't compile. Needs fixing later.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2614 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Drop AMD prototype mainboards that were for internal testing &
validation use only.
Note: These boards could never be purchased. No reasons to worry.
Questions welcome via private mail.
Signed-off-by: Yinghai Lu <yinghai.lu@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2609 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
abuild with a payload. Trivial
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2608 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
artecgroup/dbe61
Add CONFIG_COMPRESSED_PAYLOAD_NRV2B to Options.lb since it's used in
Config.lb.
Change default for CONFIG_PCI_ROM_RUN to 1 so VGA ROM can run.
technologic/ts5300
Removed CONFIG_CONSOLE_VGA, the embedded board has no VGA without the
development addon card anyways.
Changes to target Config.lb so it actually builds.
Signed-off-by: Peter Stuge <peter@stuge.se>
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2607 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
* going back to old board specific dsdt for agami aruma.
This is hopefully dropped again some day, but until then
here's a working solution.
* Some minor Agami specific changes.
* drop obsolete bringup workaround hyperclocking.diff
* increase image size again, x86emu wants it.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2606 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
* Drop empty file (0 bytes) northbridge/amd/amdk8/cpu_rev.c
and references to it.
* move config option decision to preprocessor instead of code
since config options can not change during runtime
* slightly more verbose output in built_opt_tbl.c
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2586 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
It's not fully working, among other things because the Intel
440BX northbridge isn't working, yet.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2580 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This is pretty trivial, as it was correct in the original non-CAR code.
Suddently, CAR works nicely.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2572 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
It does the ROM_STREAM -> PAYLOAD rename that afaik was done after
Yinghai sent his work to legal, so it is required to get that code
building.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Peter Stuge <peter@stuge.se>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2561 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2557 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
* Nvidia l1_2pvv
* Gigabyte m57sli
* Supermicro h8dmr
* Tyan s2912 -- with HTX
The boards will currently _not_ compile, two further patches
from Yinghai Lu are still missing. Please be patient :)
Signed-off-by: Yinghai Lu <yinghai.lu@amd.com>
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2554 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
most people.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2545 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Luis Correia <luis.f.correia@gmail.com>). The code is loosely based on
the Eaglelion 5bcm mainboard.
Warning: this is work in progress!
As of now, it does boot with serial console only (no vga), and two ethernet
cards work sometimes. This has to do with the IRQ assignments, which are a
complete mess. USB is now apparently working, but I can't make any device
to be recognized.
The PCI slot is still unusable due to the IRQ thing.
Audio, other serial ports, irda, floppy and paralell port support is
unknown aka untested yet.
(closes#32)
Signed-off-by: Luis Correia <luis.f.correia@gmail.com>
Acked-by: Acked-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2508 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
pmtools packages of upcoming SUSE 10.2, too, so the problem will
go away. (new package installed on linuxbios.org, too)
See also
http://www.linuxbios.org/pipermail/linuxbios/2006-September/015968.html
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2498 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
and leaving enough room for a real payload (not /dev/null)
This is a wonderful example why "uses" sucks.
* add Config-abuild.lb for those boards that dont build with
the default settings and a real payload:
arima/hdama, amd/quartet, amd/serengeti_cheetah, ibm/e326
* if lzma is installed and a real payload is used, try compressing
it.
* fix a small bug in "abuild --help"
This patch is acked by me because its due to infrastructural changes only.
Flames welcome.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2496 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
same format for all CHIP_NAME() entries in LinuxBIOS (Closes#20).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@linuxbios.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2490 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
long time and I could not get into the tracker.
These are patches to enable ms9185 support. Abuild passes.
Signed-off-by: bxshi <bxshi@msik.com.cn>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2486 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Richard Smith <smithbone@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2483 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
will then rename the E7520 and E7525 directories respectively.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2477 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
and (hopefully) the correct canonical name of the vendor and board.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2476 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
will then rename the src/superio/NSC directory to src/superio/nsc.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2472 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
me fix this before committing first.
Signed-off-by: Yinghai Lu <yinghailu@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2469 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
another commit is following
Signed-off-by: Yinghai Lu <yinghailu@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2468 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
add devices for the lx and artecgroup/dbe61
point artecgroup at cs5536_lx as it is so different.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2420 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Carl-Daniel Hailfinger
Signed-off-by: Ronald G. Minnich
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2413 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
USB P4 is disabled by default and we need to setup the mux bits proper
to make it work. This is the frame work for that. All thats needed
is the right address values
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2387 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
amd gx2 north -- don't set anything in the north, it conflicts with vsa
settings. So we have our own pci_set_resources that is essentially a
no-op -- just calls the kids.
olpc rev_a config -- DISABLE the compressed rom stream. This SHOULD NOT
have been set -- it is untested and caused real trouble.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2369 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
* src/cpu/amd/model_lx/model_lx_init.c
L2 cache initialization removed (moved to northbridge.c)
* src/include/cpu/amd/lxdef.h
more checked values
* src/northbridge/amd/lx/northbridge.c
L2 cache initialization added
cpubug() commented out
* src/northbridge/amd/lx/raminit.c
empty function sdram_set_registers() is in use, don't remove
* src/mainboard/artecgroup/dbe61/Config.lb
irqmap changes
* src/mainboard/artecgroup/dbe61/irq_tables.c
tentative changes to irq table (currently not in use)
* src/mainboard/artecgroup/dbe61/mainboard.c
irq assigned manually to NIC
* src/mainboard/artecgroup/dbe61/Options.lb
gcc 4.0 is OK
* targets/artecgroup/dbe61/Config.lb
64K for VSA is OK at moment
Signed-off-by: Indrek Kruusa <indrek.kruusa@artecdesign.ee>
Signed-off-by: Andrei Birjukov <andrei.birjukov@artecdesign.ee>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2360 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
read code. SBbus reads to RAM now work. Yah!
- Rename the register constants to something I can look at
more easily.
- Make the logic flow match the flow from V1 assembly
- #if 0 out other SMbus functions that are still broken.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2353 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Re-enable the SPD dump routine in this Bitworks/IMS code and make
it work like the Asus/p2b. This avoids having to hack the
sdram/generic_dump_spd.c for a single mem controller.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2352 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- New superIO winbond/w83977tf
- Add single memory controller SBbus debug routine
into a file private to the i440bx
This adds support the start of support for an Asus p2b
mainboard. Current limitations are the same as for the
Bitworks IMS board. Reads from the SMbus don't work.
Moving dump_spd_registers() into its own private copy
solves the problem of having to go hack on the version that
included in src/sdram to only do one memory controller.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2351 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
There is one global change to pci_ids.h. The rest are changes for LX. I
ran abuild and it is ok. Not all artec design changes are included as
some of them would adversely affect other mainboards. Indrek will need
to test.
Signed-off-by: Ron Minnich
Signed-off-by: Indrek Kruusa, indrek.kruusa@artecdesign.ee, artec
design.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2350 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
add support for NSC pc87351 SuperIO
add Bitworks/IMS manboard config
This is a very basic framework for the i440bx chipset and the
Bitworks IMS board that uses it. Most things are
structure only.
Known issues:
- SMbus reads to the RAM SPD come back
all zero.
- dump_spd_registers() is commented out since it breaks with
the default setting of generic_dump_spd.c where it wants
2 memory controllers.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2347 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
disabled.
cs5536: add new entires for SB control etc.
cs5536.c: chip_enabled function moved to chip_init, so it only gets run
once.
IRQ setup improved
gx2def.h: new defines added
vr.h: new file, with new def's for virtual register control.
mainboard config.lb: new entries added for nb and sb control.
chipsetinit.c: new controls added -- I forget all the details :-)
grphinit.c: new function added
northbridge.c: new IRQ control added. FlashChipSetup added, controlled
by chip info setupflash struct member. Currently, if enabled, this hangs
OLPC in linux PCI scan.
chip.h: new struct members added for unwanted device enable, flash setup
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2345 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
breaking a build is intentional. It will be fixed in a bit.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2338 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
manage them. Make pci_level_irq global. Add value settings for OLPC
rev_a board. Comment out no-longer-needed code in olpc mainboard.c
-- it is replaced by the settings in Config.lb, and the support
in cs5536.c
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2328 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
olpc and rumba can now boot linux out of flash. vsa was resized to 64K.
olpc and rumba now used compressed payload -- thanks stefan!
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2307 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Default is 255.
This allows mainboard configs for working across various groups
of boards that differ a device that may not loaded.
If you search for a device that is not loaded and max buses is 255
then there can be up to a 8 second delay to search the entire PCI space.
Board configs that know thier max bus can limit this search space.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2273 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
on a SOM-DB2301 baseboard with a SOM-2354 cpu module.
- Also does a slight tweak to the ram test code to make it more
obvious when it fails.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2231 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- some ts5300 code. Let's push this upstream for now.
- fix a typo in device.c
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2211 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
vsa on geode GX.
There was some bug in setting up stack, what was that?
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2208 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
other fixes for gx2 ram init.
support for sharplfg00l04 -- not working yet.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2197 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This is just a skeleton, basically, and will most likely not even
compile yet.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2164 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
disable agp slot in config.lb
fix error in setting up com1 == should be TTYS0_BAUD
note that the uart8250 struct is a bad design, but so is the
uart8250 code.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2161 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
store every HT device unit id base and pass those info to acpi
https://openbios.org/roundup/linuxbios/issue46
Note: This version drops the two scripts a and c and creates the dsdt on
the fly from Config.lb using makerule
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2134 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
to fail later than before.
dos2unix'ed the xe7501devkit files, that might have caused some problems
before.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2127 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Joseph Smith