Fix the ctrl_devport_conf_clear to clear the enable bit.
A simplification:
Dynamically enable ck804s that are found instead of relying on #defines.
Removing an Opteron changes the number of ck804s that are present.
Simple changes to make it easier to compare the factory BIOS with Coreboot when
using SerialICE for boards with the Nvidia ck804 chipset:
If the mask is zero, don't read the value, just write the new value over it.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5652 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Joseph Smith <joe@settoplinux.org>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5637 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
there is no free list.
Converting resource arrays to lists reduced the size of each device
struct from 1092 to 228 bytes.
Converting link arrays to lists reduced the size of each device struct
from 228 to 68 bytes.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5626 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
However on these platforms we were causing a resource conflict by
letting the resource allocator start allocations at 0x400.
Change the constraints to start at 0x1000 so we avoid allocating over
LPT ports (0x778-0x77f), PCI (0xcf8-0xcff) and some other fixed
resources that might live down there (smbus base, acpi base,...)
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5624 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
range as detailed on p104 of the cs5536 Device Data Book.
Extended to 0x1000. Same change for cs5535.
Signed-off by: Edwin Beasant edwin_beasant@virtensys.com
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5618 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
108 src/arch/i386/include/arch/acpi.h:402:5: warning: "CONFIG_HAVE_ACPI_SLIC" is not defined
1 src/mainboard/getac/p470/mainboard.c:83: warning: assignment discards qualifiers from pointer target type
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5614 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
src/cpu/amd/model_fxx/model_fxx_update_microcode.c
src/northbridge/amd/amdk8/amdk8_acpi.c
src/southbridge/amd/amd8132/amd8132_bridge.c
Signed-off-by: Frank Vibrans <frank.vibrans@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
http://www.coreboot.org/pipermail/coreboot/2010-June/058668.html
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5607 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
To apply this patch you need to
cp src/northbridge/amd/gx2/chipsetinit.c src/southbridge/amd/cs5535/
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Nils Jacobs <njacobs8@hetnet.nl>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5589 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
coreboot is direct. This patch does it.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5586 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
cs5536.c:chipsetinit() is called during northbridge pci_domain_enable()
which happens before scan_bus() so the device tree does not have PCI
vendor/device ids yet. Let's use dev_find_slot() for now. This works
only as long as the CS5536 has PCI device id 0xf in all mainboards,
and a better solution is needed in case that ever changes!
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Nathan Williams <nathan@traverse.com.au>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5581 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
In the bootblock, 4MB of ROM are mapped instead of the
default 1MB
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5580 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
while others dislike them being extra commits, let's clean them up once and
for all for the existing code. If it's ugly, let it only be ugly once :-)
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5507 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
were not treated separately until now. Fix it. Hope self ack is OK,
compiled tested locally.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5497 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
to option based (similar what Uwe did) and also it uses GFXUMA to handle the
high_tables_start offset from memory top.
To satisfy the CMOS option users (Hi, libv! ;) I added also a possibility to do
that through CMOS.
Fixed printks to match the new style.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5494 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
independent of strapping, making larger flashes work. We cannot walk anything
else than PCI bus 0 because HT is not setup yet.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5485 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
* integrate vsm init into normal x86.c code (so it can run above 1M)
* call void main(unsigned long bist) except void cache_as_ram_main(void)
on Geode LX (as we do on almost all other platforms now)
* Unify Geode LX MSR setup (will bring most non-working LX targets back
to life)
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5471 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
only. Keeping them as #warnings will not likely that they're fixed.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5459 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
remove more warnings.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5397 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The tyan s2895 is down to 3 warnings, 2 of which are caused by #warning.
The 1000 ways of how the AMD code waits for the cores to be started up
are a real pain for the brain.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5396 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2. Add support for Micro-FCBGA 479 Celeron and PIII's
3. Add support for model_6bx and microcode updates
4. Add support for CAR and Tinybootblock on RCA RM4100 and Thomson
IP1000
Build and boot tested.
Signed-off-by: Joseph Smith <joe@settoplinux.org>
The change to CAR reveiled a few more warnings in the ICH4 and i830 code,
I fixed them on the fly.
Checking this in because my last two commits broke Joseph's CAR patch. This
version fixes the issues.
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5388 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
last round for today. still warnings - help appreciated.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5363 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- cleanup reset
- some minor warning fixes.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5361 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5356 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Only some assembler files still have \r\n ... Can we move that part to C
completely?
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5342 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Interesting enough, console_printk was only used in a single place and
duplicated a large part of console.h which is included in the same place.
Thus, just drop console_printk.c and we're one down with console complexity
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5274 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Joseph Smith <joe@settoplinux.org>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5270 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Some other random warnings.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5268 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5266 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CONFIG_CAR_FAM10 was renamed some time ago to
CONFIG_NORTHBRIDGE_AMD_AMDFAM10, and l3Cache() is actually defined as
l3_cache().
Signed-off-by: Ed Swierk <eswierk@aristanetworks.com>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5262 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Boot Tested (bootlog attached)
Signed-off-by: Joseph Smith <joe@settoplinux.org>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5244 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
otherwise it will keeps reboot. The comment was also added in
detail to make less confusing when we debug SB600/SB700.
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5240 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5223 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Makefile and Kconfig.
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5222 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
* PCIe initialization.
* Internal Graphics initialization.
* HT Link initialization. It works in HT1 or HT3 mode.
Note:
1. I tried to add the description of every step to the code. For example,
if it is made based on rpr, section 2.4.5, I will pasted the words
from 2.4.5 to the c code. But the document I worked with might be
different with the most updated one. A new section has been added and
the 2.4.5 might be changed to 2.5.5. That migh lead to confusing. I
correct every comment if I met one. But I have to confess that I am so
reluctant to find out everyone. I believe it will be correct in the long
run.
2. The interanl graphics part is done by Libo Feng <libo.feng@amd.com>.
3. There is a conflict between RPR and our CIM code. Please see the comment in
switching_gppsb_configurations in rs780_pcie.c.
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5219 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
* SATA initialization.
* USB initialization.
* HDA initialization.
* LPC initialization.
* IDE initialization.
* SMBUS initialization.
Note:
1. I tried to add the description of every step to the code. For example,
if it is made based on rpr, section 2.4.5, I will pasted the words
from 2.4.5 to the c code. But the document I worked with might be
different with the most updated one. A new section has been added and
the 2.4.5 might be changed to 2.5.5. That migh lead to confusing. I
correct every comment if I met one. But I have to confess that I am so
reluctant to find out everyone. I believe it will be correct in the long
run.
2. I only test the SATA port 0-3. The ports 4, 5 are "PATA emulations".
I am confused about it.
3. This patch is not only about SB700. Actually it should be
SB7x0. But I dont think it is nice to change everything to
SB7x0. It is ugly, isn't it. As far as I know, they all use the
same code with revision checking. If you guys think it is
appropriate, please modify it to sb7x0.
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5218 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
fix some PCI IDs, enable USB bus mastering, add some license headers, ...
LPC code needs another look, but I think we're getting there.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Joseph Smith <joe@settoplinux.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5207 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Previously the sb600 setup was equivalent to clear_ioapic(), so that is what we will do for now.
Signed-off-by: Marc Jones <marcj303@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5199 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Convert all DEBUG_SMBUS, DEBUG_SMI, and DEBUG_RAM_SETUP custom and
local #defines into globally configurable kconfig options (and Options.lb
options for as long as newconfig still exists) which can be enabled
by the user in the "Debugging" menu.
The respective menu items only appear if a board is selected where the
chipset code actually provides such additional DEBUG output.
All three variables default to 0 / off for now.
Also, drop a small chunk of dead/useless code in the
src/northbridge/via/cn700/raminit.c file, which would otherwise break
compilation.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Reworked to still apply to trunk, added X86EMU_DEBUG (and make the x86emu/yabel
code only work printf instead of a redefined version of printk and
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5185 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This is needed on the IP1000T to get VGA output. The VGA option rom will ask
through an SMI for hardware specifics (in form of a VBT, video bios table)
which the SMI handler copies into the VGA option rom.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5177 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
(chipset_bootblock_inc and chipset_bootblock_lds) instead of using
chipset specific rules for "bigbootblock" in the generic i386 Makefile.
It also adds rules for the romstraps of
* southbridge/nvidia/ck804
* southbridge/sis/sis966
* northbridge/via/vx800
for the benefit of both image layouts.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5175 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
cd coreboot/src/southbridge
svn mv i82801ca i82801cx
svn mv i82801dbm i82801dx
svn mv i82801er i82801ex
svn copy i82801xx i82801bx
svn mv i82801xx i82801ax
Plus, fixing up the filenames in these directories and the romstage.c and
Kconfig files of the mainboards using those drivers.
Plus, switching the thomson ip1000 and rca rm4100 to the i82801dx driver.
There's a lot more to be done, like
- adding device IDs for the ICH3 and newer drivers that have been kept in
i82801xx so far
- drop the additional parts support from the ax and bx drivers.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Joseph Smith <joe@settoplinux.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5167 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
PS/2 keyboard API.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5152 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- drop include/part and move files to include/
- get rid lots of warnings
- make resource allocator happy with w83627thg
- trivial cbmem resume fix
- fix payload and log level settings in abuild
- fix kontron mptable for virtual wire mode
- drop some dead includes and dead code.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5136 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Consistently use the same wording and formatting for all license headers.
- Remove useless whitespace, add missing whitespace, fix indentation.
- Add missing "This file is part of the coreboot project." where needed.
- Change "(C) Copyright John Doe" to "Copyright (C) John Doe" for consistency.
- Add some missing "(C)" strings and copyright years where needed.
- Move random comments and file descriptions out of the license header.
- Drop incorrect file descriptions completely (e.g. lpc47m10x/Makefile.inc).
There should be no changes in _content_ of the license headers, if you spot
such changes that's a bug, please report!
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5127 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Permit early setup of COM2
Signed-off-by: Edwin Beasant <edwin_beasant@virtensys.com>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5097 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
cache_as_ram_auto.c and auto.c are both called "romstage.c" now.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5092 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5089 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
GPIO lines 4 and 3 are swapped and also incorrectly put in IR mode receive (compound fault).
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Edwin Beasant <edwin_beasant@virtensys.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5074 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5060 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Add appropriate Kconfig defines to provide 8mb of VGA ram allocation
Add the Kconfig defines to cover TSC calibration from TIMER2 and UDELAY setup
Two small warning removals about excessive prototyping.
Signed-off-by: Edwin Beasant <edwin_beasant@virtensys.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5059 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
from mainboards.
Some adaptations were necessary after the IOAPIC cleanup,
so this should fix the build.
Fix intel/d945gclf build, which was missing some ACPI component.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5039 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5029 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
* change the code to use macros names instead of constants in many places
* SMI/ACPI: rework power-off code to work with old Linux kernels (2.6.12.x)
* SMI: Add support for mainboard GPI handler
* SMI: immediate power-off on power button press, if OSPM is not active
* Add fix for some USB errata
* Some register tweaks for mobile systems
* Enable configure SCI on interrupt 9 correctly.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5026 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
of components. This patch is a rewrite of the generic IOAPIC setup code.
Additionally it drops the other 12 instances of IOAPIC setup code and
makes the components use the generic code.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5023 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
read32(unsigned long addr) vs readl(void *addr)
and
write32(unsigned long addr, uint32_t value) vs writel(uint32_t value, void *addr)
read32 was only available in __PRE_RAM__ stage, while readl was used in stage2.
Some unclean implementations then made readl available to __PRE_RAM__ too which
results in really messy includes and code.
This patch fixes all code to use the read32/write32 variant, so that we can
remove readl/writel in another patch.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5022 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
* drop debug.c files from 945 mainboards (and share it in the northbridge code)
* adapt the mainboard and auto.c files for above changes.
Rather trivial
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5016 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This patch also aligns the configuration of a couple of
boards more closely to what newconfig does.
Also, the romstrap inc/lds files are declared in the
Makefiles of the southbridges they belong to, instead of
some global file.
AMD CPUs have their own timer functions, so disable UDELAY_IO
for them and set HAVE_INIT_TIMER as appropriate, same for
emulation/qemu-x86.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5000 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Set __PRE_RAM__ define per default
- Properly handle ignored (#ifdef'd out) #include lines
amd/serengeti_cheetah_fam10:
- write ACPI files to $(obj) instead of the top dir (alias $(CURDIR))
tinybootblock:
- provide a way to define code that should be added to the bootblock,
to map the entire ROM for use by CBFS
amd/model_fxx, amd/model_10xxx:
- add CONFIG_SSE
walkcbfs.S:
- eliminate the use of two registers, to make space for romcc to wiggle
amd/serengeti_cheetah_fam10:
- use the enable_rom framework. not entirely functional yet
Boot-tested on emulation/qemu-x86
Build-tested on amd/serengeti_cheetah_fam10
amd/serengeti_cheetah_fam10 fails in amdht/ somewhere, but builds
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4994 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
which is normally set to 0x10 (the current default) and set to 0x80 (the current alternative)
where necessary (if romstraps get in the way).
For Kconfig, the special case is set per southbridge (as these define the necessity for this
workaround), for newconfig it's added to each single board.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4962 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
now handled more generically using CBFS.
Simplify the option ROM code in device/pci_rom.c, since there are only two ways
to get a ROM address now (CBFS and the device) and add an exception for qemu.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4925 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Since we have CBFS setting rom_address in board files is no longer
necessary.
Also, drop vga_rom_address from RS690 completely, it was never used
in the code.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4923 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
__ROMCC__ now means "Don't use prototypes, since romcc doesn't support them."
__PRE_RAM__ means "Use simpler versions of functions, and no device tree."
There are probably some places where both are tested, but only one is needed.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4921 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Declare superio functions to be static and remove duplicates.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4890 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Add static and const where possible.
- Turn some #warning entries into TODO comments.
- Add missing prototypes.
- Remove unused variables.
- Fix printf arguments or cast them as needed.
- Make sconfig output look better. Drop useless "PARSED THE TREE" output.
- Print "(this may take a while)" while building romcc. Add missing "\n".
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Myles Watosn <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4874 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
TODO
- x86emu need (imo) some common header with prototypes at least
- clog2, ulzma, hardwaremain prototypes added by this patch probably should
be moved to some header too.
- in src/devices/device_util.c prototype is before function because seems,
it is used only within same file, if not it should be moved to debug
section of prototypes in include/device/device.h
Signed-off-by: Maciej Pijanka <maciej.pijanka@gmail.com>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4871 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- run ACPI code through preprocessor so we get the same values
as the C code
- fix PCIe x16 slot
- fix ICH7 Azalia/HDA driver
- SMI/GNVS update security fix (only allow struct pointer update once)
- ACPI updates
- IDE driver fixes
- add cmos options for disabling onboard ethernet and controlling system fan
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4861 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
ppc port, some ambiguous use of CONFIG_IDE and an unused ide driver (we dropped
the filesystems already to be used with it) (somewhat trivial)
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4828 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Change HAVE_FAN_CTL to be specific to the SuperIO that supports it.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4809 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
VGA ROM can not run. After make, run
> ./cbfs/cbfstool ./coreboot.rom add ../vga_bios.rom pci1002,791f.rom optionrom
to make the final image with vga bios.
The macro vga_rom_address is out-of-date when CBFS starts play its role. it also should
be eliminated from rs690/chip.h as below. But it will cause building error on other board, which I
cant make test on.
## Index: src/southbridge/amd/rs690/chip.h
## ===================================================================
## --- src/southbridge/amd/rs690/chip.h (revision 4782)
## +++ src/southbridge/amd/rs690/chip.h (working copy)
## @@ -23,7 +23,6 @@
## /* Member variables are defined in Config.lb. */
## struct southbridge_amd_rs690_config
## {
## - u32 vga_rom_address; /* The location that the VGA rom has been appened. */
## u8 gpp_configuration; /* The configuration of General Purpose Port, A/B/C/D/E. */
## u8 port_enable; /* Which port is enabled? GFX(2,3), GPP(4,5,6,7) */
## u8 gfx_dev2_dev3; /* for GFX Core initialization REFCLK_SEL */
##
Don't apply above patch about rs690/chip.h before every board has been fixed.
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4783 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
to build, but by default all the tables that are available are built.
Make PIRQ table build for qemu.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4778 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Reset the s2891 so the HT speed gets updated.
Remove some PANTA comments.
Add SATA init from non-CAR version.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4771 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
There is an i2c mux out there. We found it using a user level program
that, as usual, began by inverting all gpios until we found out
what we needed to know. In the end, we just set up the GPIOs as
the factory bios does.
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4755 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Use "default n" for all components that shall be "select"ed.
- Use "0x0" instead of "0" for hex variables for clarity and to reduce
the risk of people passing integer instead of hex values to such variables.
- Add TODO comments for boards that have irq_tables.c but don' set
CONFIG_HAVE_PIRQ_TABLE = 1. Someone with the hardware should test enabling.
- ASUS M2V-MX SE doesn't have irq_tables.c so don't define
IRQ_SLOT_COUNT in its Kconfig file.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4749 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4748 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
their own vgabios.c
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4744 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4731 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
in very early stages, otherwise the boot may hang like this because
the CBFS headers cannot be found/accessed:
Uncompressing coreboot to RAM.
Jumping to image.
Check CBFS header at fffedfe0
magic is ffffffff
ERROR: No valid CBFS header found!
CBFS: Could not find file fallback/coreboot_ram
Jumping to image.
This patch enables full ROM access on all 440BX boards right after the
serial init (and before CBFS headers are parsed).
Build-tested and runtime-tested on ASUS P2B-F.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4721 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Both were only really used in pre-cbfs, as the payload's size isn't
relevant for the build process anymore.
Various calculations in {no,}failovercalculation.lb are adapted
accordingly.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4720 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4719 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- northbridges are done
- southbridges are done
- Intel CPUs are done, with a design that the board only has to specify
the socket it has, and the CPUs are pulled in automatically. There is
some more cleanup possible in that area, but I'll do that later
- a couple more mainboards compile:
- intel/eagleheights
- intel/jarrell
- intel/mtarvon
- intel/truxton
- intel/xe7501devkit
- sunw/ultra40
- supermicro/h8dme
- tyan/s2850
- tyan/s2875
- via/epia
- via/epia-cn
- via/epia-m
- via/epia-m700
- via/epia-n
- via/pc2500e
(PPC not considered, probably overlooked something)
All of them only _build_, but some options are probably completely
wrong. To be fixed later
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4673 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
src/cpu/amd/socket_F/Kconfig: Remove second occurrence of CPU_SOCKET_TYPE.
src/mainboard/amd/serengeti_cheetah/Kconfig: Add HT_CHAIN_UNITID_BASE here, since it is board specific.
src/mainboard/tyan/s289X/Kconfig: Fix typo and change APIC_ID_OFFSET to match old config.
src/devices/Kconfig: Change default value of *_PLUGIN_SUPPORT to match old config.
src/southbridge/amd/amd8131/Makefile.inc: Remove check since it was a typo, and the correct variable is checked in the parent directory.
src/Makefile:Use devicetree.cb instead of Config.lb to generate static.c.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4657 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
kconfig_s2892.dif: Add support for Tyan s2891, s2892, and s2895 to Kconfig.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4656 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
write. It boots the SB/NB V-link performance to full duplex 533MB/s. (in fact x2
for FDX)
The default was 266MB/s but half duplex only. If you encourage any stability
issues we need to look into fine tuning the bus. The values are VIA recommended.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4625 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
tested. I also addressed questions raised by Uwe:
TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
UDELAY_TSC
Are now defined as booleans in src/cpu/x86/Kconfig and can be selected in
the mainboard Kconfig. The remaining question of Uwe's is a deeper
problem:
---
We'll have to check if this works. From a quick glance
the Rumba does not have the mmx related lines (which _are_ in
Makefile.romccboard.inc, though):
crt0-y += ../../../../src/cpu/x86/fpu/enable_fpu.inc
crt0-y += ../../../../src/cpu/x86/mmx/enable_mmx.inc
crt0-y += auto.inc
crt0-y += ../../../../src/cpu/x86/mmx/disable_mmx.inc
---
We're going to need a whole variant of this standard mainboard OR
we're going to have to make (some) of the unconditional includes above
conditional.
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4618 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This patch tries to improve the pcie portA configuration.
The Matrox G550e PCIe gfx card shipped along with the dev board is supported.
Signed-off-by: Arnaud Maye <arnaud.maye@4dsp.com>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4615 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4613 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
It also brings in the vsm from v3, which was a much cleaner cut.
Over time, I hope to bring all the code back from v3. I have
some rumbas at home and want to use them.
I have a patch which comes in next that makes the rumba build.
Note that I am holding the src/*/amd/Kconfig patch until these get merged.
These have no impact on the current system.
Note that this is not complete but I want to fill in the blanks bit
by bit.
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4611 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The SB600 SATA code printed that two BARs had the same address because
it didn't mask the correct number of bits in the BAR.
Functionality was not affected, but the debug output was incorrect.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Zheng Bao <zheng.bao@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4591 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
monitors.
Signed-off-by: Libra Li <libra.li@technexion.com>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4585 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Whitespace fixes, remove trailing whitespace, use TABs for identation
(except in Kconfig "help" lines, which start with one TAB and two spaces
as per Linux kernel style)
- Kconfig: Standardize on 'bool' (not 'boolean').
- s/lar/cbfs/ in one Kconfig help string.
- Reword various Kconfig menu entries for a more usable and consistent menu.
- Fix incorrect comment of NO_RUN in devices/Kconfig.
- superio/serverengines/Kconfig: Incorrect config name.
- superio/Makefile.inc: s/serverengine/serverengines/.
- superio/intel/Kconfig: s/SUPERIO_FINTEK_I3100/SUPERIO_INTEL_I3100/.
- mainboard/via/vt8454c/Kconfig: Fix copy-paste error in help string.
- mainboard/via/epia-n/Kconfig: Fix "bool" menu text.
- console/Kconfig: Don't mention defaults in the menu string, kconfig
already displays them anyway.
- Kill "Drivers" menu for now, it only confuses users as long as it's emtpy.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4567 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Note the makefile.inc may be out of date given the new commits of code
today, but this is what was signed off ...
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4551 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Tested on Via EPIA-NL8000EG with FILO payload booting FC9 (2.6.25
kernel) from SATA HDD.
ACPI is working for PCI interrupt routing, some memory stuff and
Soft-Off.
USB/SATA Working
VGA Console Working
X Working via Onboard AGP
Removed dsdt.c, fixed some whitespace.
Signed-off-by: Jon Harrison <bothlyn@blueyonder.co.uk>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4549 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4537 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4535 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Works on Kontron, qemu, and serengeti.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
tested on abuild only.
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4534 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Add initialisation for the VIA Chrome 9 IGP on the k8m890 through native code
and through the general vga infrastructure i committed a month or two ago.
Add videoram_size option for k8m890 and the Asus M2V-MX SE.
Now the Asus M2V-MX SE will magically come up with a working standard VGA
80x25 textmode.
Many thanks to the people who worked hard on the Asus M2V-MX SE, and all
of its components; this vga bringup was a breeze thanks to your hard work
for this excellently supported board. And separate thanks to Rudolf Marek
for spurring me on and for providing a register dump.
Signed-off-by: Luc Verhaegen <libv@skynet.be>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4465 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- code restructuring (move ich7 out of i945)
- ACPI fixes
- major SMI handler updates
- make sure SMBus lives where we expect it
- try to get usb debug working
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4456 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- drop duplicate udelay function
- simplify code flow
- some cosmetics on comments
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4445 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
those symbols were left alone before, after this, they're
somewhat more in line with the rest of the tree.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4442 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
single core.
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4415 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Major changes:
1. Separate resource allocation into:
A. Read Resources
B. Avoid fixed resources (constrain limits)
C. Allocate resources
D. Set resources
Usage notes:
Resources which have IORESOURCE_FIXED set in the flags constrain the placement
of other resources. All fixed resources will end up outside (above or below)
the allocated resources.
Domains usually start with base = 0 and limit = 2^address_bits - 1.
I've added an IOAPIC to all platforms so that the old limit of 0xfec00000 is
still there for resources. Some platforms may want to change that, but I didn't
want to break anyone's board.
Resources are allocated in a single block for memory and another for I/O.
Currently the resource allocator doesn't support holes.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4394 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Jon Harrison <bothlyn@blueyonder.co.uk>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4389 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
It's basically done with the following script and some manual fixup:
VARS=`grep ^define src/config/Options.lb | cut -f2 -d\ | grep -v ^CONFIG | grep -v ^COREBOOT |grep -v ^CC`
for VAR in $VARS; do
find . -name .svn -prune -o -type f -exec perl -pi -e "s/(^|[^0-9a-zA-Z_]+)$VAR($|[^0-9a-zA-Z_]+)/\1CONFIG_$VAR\2/g" {} \;
done
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4381 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Add initial ACPI support for M57SLI.
Activates/Enables:
* native Coreboot ACPI for M57SLI
* Soft-Power-Off
* PowerNow!
* High Precision Event Timer
* Windows booting with ACPI support
Signed-off-by: Harald Gutmann <harald.gutmann@gmx.net>
Acked-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4364 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Any endless loop after die() can be eliminated.
Dereferencing a NULL pointer is bad. die() instead.
Replace endless loops with die().
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4340 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
starts to play its role. Then the system hangs at HDA init. I dont know what the
VC1 is. The RPR says "Optional Features (only needed if CMOS option is enabled)"
in 5.10.2. Before I know what it is, I think it is better to skip it.
Tested on dbm690t.
Add comment from Rudolf,
"
VC is virtual channel. Its used for isochronous transfer of data to sound card.
The virtual channel guarantee "on time" delivery. In other words it sets up a
channel for data to sound card, which means that that arrivs in time and there will
be no interuptions in audio stream.
http://www.microsoft.com/whdc/connect/pci/wlp_interrupt.mspx
"
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4339 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
1. In rs690_cmn.c, mask the lower 4 bits of the BAR3. No doubt, right?
2. In rs690_pcie.c,
(1) Obviously, the mask should be 0xF, and bit 19 should be set to 1 (in comment).
In rpr 5.10.2, step 2, step 2.1 & step 2.6
(2) The dynamic buffer allocation is enabled by setting bit 11 of PCIEIND: 0x20,
instead of PCIEIND_P: 0x20.
In rpr 5.10.2, step 5. Dynamic Slave CPL Buffer Allocation
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4336 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This reverts commit eb7bb49eb5b48c39baf7a256b7c74e23e3da5660.
Stepan pointed out that "s" means string, which makes the following statement
in this commit message invalid: "Since we either have reserved space (which
we shouldn't do anything with in these two functions), an enum or a
hexadecimal value, unsigned int seemed like the way to go."
Signed-off-by: Luc Verhaegen <libv@skynet.be>
Acked-by: Luc Verhaegen <libv@skynet.be>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4335 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
To ease some of my debugging pain on the unichrome, i decided i needed to
move FB size selection into cmos, so i could test a size and then reset it
to the default after loading this value so that the next reboot uses the
(working) default again. This meant implementing set_option in parallel to
get_option.
get_option was then found to have inversed argument ordering (like outb) and
passing char * and then depending on the cmos layout length, which made me
feel quite uncomfortable. Since we either have reserved space (which we
shouldn't do anything with in these two functions), an enum or a
hexadecimal value, unsigned int seemed like the way to go. So all users of
get_option now have their arguments inversed and switched from using ints
to unsigned ints now.
The way get_cmos_value was implemented forced us to not overlap byte and to
have multibyte values be byte aligned. This logic is now adapted to do a
full uint32_t read (when needed) at any offset and any length up to 32, and
the shifting all happens inside an uint32_t as well. set_cmos_value was
implemented similarly. Both routines have been extensively tested in a
quick separate little program as it is not easy to get this stuff right.
build_opt_tbl.c was altered to function correctly within these new
parameters. The enum value retrieval has been changed strol(..., NULL, 10)
to stroul(..., NULL, 0), so that we not only are able to use unsigned ints
now but so that we also interprete hex values correctly. The 32bit limit
gets imposed on all entries not marked reserved, an unused "user_data" field
that appeared in a lot of cmos.layouts has been changed to reserved as well.
Signed-off-by: Luc Verhaegen <libv@skynet.be>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4332 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
directory just with one common file.
Changes to FADT: move to rev4, fix the generic register descriptors, detect additional VT8237S features.
Change the compiler to CORE , its revision to 42.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4327 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Joseph Smith <joe@settoplinux.org>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4324 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
patch, just removes the warnings like
coreboot-v2/src/southbridge/intel/i82801xx/i82801xx_ac97.c:73: warning: initialization discards qualifiers from pointer target type
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4302 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
src/northbridge/intel/i440bx/ but not to
src/cpu/emulation/qemu-x86/northbridge.c
It also adds a driver for the ISA device that is found when using
0.9.1 If you look in a log without this patch you won't find the RTC
init lines.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4269 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Joseph Smith <joe@settoplinux.org>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4251 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Joseph Smith <joe@settoplinux.org>
Acked-by: Joseph Smith <joe@settoplinux.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4249 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
I didn't try to remove "defined but not used" warnings because there are too
many ifdefs to be sure I wouldn't break something.
For shadowed variable declarations I renamed the inner-most variable.
The one in src/pc80/keyboard.c might need help. I didn't change the
functionality but it looks like a bug.
I boot tested it on s2892 and abuild tested it.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4240 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4108 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
part of this patch adds support for resume well NVRAM. In which DQS values are
stored.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4100 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
coreboot to 1MB and tries to cache whole range for XIP. The UMA part colide a
bit with the HAVE_HIGH_TABLES region. I solved that by relocation of the region.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4024 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Use the (almost) same strict CFLAGS in v2 that we use on v3. And fix a few
include files and missing prototypes. Also, fix up the Config-abuild.lb files
to properly work for cross compiling.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4000 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3999 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
be required for a series of later patches. Roughly it contains:
* fixed SMBus driver (was not compiled in before)
* fixed S-ATA/P-ATA combination
* Added warnings to drivers being called with a NULL dev->chip_info
* Set subsystem ids for those boards that have none specified in Options.lb
* Fix license headers. The code was originally released under GPL v2 but
some files sneaked in with a v2 or later header.
* some attempts to fix azalia/Intel HDA.. not working yet
* clean up and fix pci bridge handling code
* Add Config based GPI handling to LPC driver
* Add HPET enable function
* Enable clock gating where appropriate
* first attempt at USB debug console support (not working yet)
* Add required options to kontron board
* many other minor changes
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3991 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
changes by file:
src/northbridge/amd/amdk8/northbridge.c:
Add high tables code ala Stefan's code for the i945.
src/southbridge/nvidia/ck804/ck804_lpc.c:
Enable High Precision Event Timers.
Add pm_base for ACPI.
src/southbridge/nvidia/ck804/ck804_fadt.c:
Since fadt is only dependent on the Southbridge, add it here.
src/southbridge/nvidia/ck804/Config.lb:
Compile in ck804_fadt.c
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3988 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
a long time ago. This will make it easier to port v2 boards forward to v3 at
some point (and other things)
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3964 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- make uma_memory_base and uma_memory_size uint64_t as they may be 64bit BARs
on some platforms.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3949 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Reorder HDA (HD Audio) init:
The reordering was based on what order things happen in the BIOS
Developers guide, RPR, and SATA driver. I fixed the order of the devices
that didn't matter to clean up the change log.
1. Enable the Chip
2. Setup the SMBus registers
3. Setup the Device Registers
4. Look for Codec
5. Init Codec
The codec init was changed to match the description in the RRG pg 235.
Mem Reg: Base + 08h Bit 0. There were unneeded things happening.
Added 1ms delay to match the BKDG while waiting for BAR+0xe to set its
bits.
Signed-off-by: Dan Lykowski <lykowdk@gmail.com>
Tested on AMD DBM690T and AMD Pistachio by Maggie Li. Works.
Tested on Asus M2A-VM by Carl-Daniel Hailfinger. Improves the situation,
but some warnings remain.
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3930 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Maggie Li <maggie.li@amd.com>
Reviewed-by: Zheng Bao <Zheng.bao@amd.com>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3891 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3887 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- use new features of the ich7 update
- move rambase above 1M to avoid memory trashing through SMM relocation
- enable superio HWM
Update ICH7 driver
- minor smi cosmetics (in progress)
- add real ac97 driver
- add real azalia driver
- fix some interrupt issues
- fix some sata issues
- include Patrick's fix for _lpc.c
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3886 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
parts.
This should help to reduce the code duplication for Rudolf's K8/VIA SMM
implementation...
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Joseph Smith <joe@settoplinux.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3870 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
SATA port status kept returning 0x1: BAR5+po+28h
1h = Device presence detected but Phy communication not established
This patch adds logic to force 1.5g if the drive fails to communicate at 3.0g.
Signed-off-by: Dan Lykowski <lykowdk@gmail.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3864 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
is no longer 0xA0 or 0xB0. It simply assumes that will never happen.
My 500 GB Seagate Barracuda ST3500820AS triggers that corner case on the
first init after poweron.
The current code hangs forever with my drive. Fix this by rerunning the
init sequence after SATA_BAR0+6 is no longer 0xA0 or 0xB0.
Add support for SATA port 2-4 (Primary Slave, Secondary Master,
Secondary Slave).
If only the 2nd SATA port is connected and the hardware acts strangely
(contrary to documentation), it will print the error message below and
continue anyway. The official AMD asm code behaves the same way.
SATA port 0 status = 0
No Primary Master SATA drive on Slot0
SATA port 1 status = 23
0x6=7f, 0x7=7f
drive no longer selected after 0 ms, retrying init
[8 repetitions]
0x6=7f, 0x7=7f
drive no longer selected after 0 ms, retrying init
Primary Slave device is not ready after 10 tries
Activate and improve debug messages for SPEW log level.
Fix some comments.
New log messages look like this:
PCI: 00:12.0 init
sata_bar0=3020
sata_bar1=3060
sata_bar2=3030
sata_bar3=3070
sata_bar4=3000
sata_bar5=fc309000
SATA port 0 status = 23
0x6=a0, 0x7=80
drive detection not yet completed, waiting...
0x6=a0, 0x7=80
drive detection not yet completed, waiting...
[... 281 repetitions ...]
0x6=0, 0x7=50
drive no longer selected after 2820 ms, retrying init
drive detection done after 0 ms
Primary Master device is ready after 2 tries
SATA port 1 status = 23
drive detection done after 0 ms
Primary Slave device is ready after 1 tries
SATA port 2 status = 0
No Secondary Master SATA drive on Slot2
SATA port 3 status = 0
No Secondary Slave SATA drive on Slot3
With this patch, my Asus M2A-VM boots into Linux without problems.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Zheng Bao <zheng.bao@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3845 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The RS690 chipset has a problem where it will not work with 1 GHz HT
speed unless NB_CFG_Q_F1000_800 bit 0 is set.
Tested, works on my Asus M2A-VM with an 1 GHz HT capable processor.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Bao, Zheng says:
As a matter of fact, both 600Mhz and 1Ghz have their own specific
setting.
This patch has been tested on dbm690t which HT link works on 800Mhz.
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3839 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The device ID of 690G is 0x791E, while the ID of 690M and 690T is 0x791F
This fixes booting on 690G.
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3816 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
mainboard specific code. (And add a hook to allow other mainboards do
a similar thing if required)
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Ronald G Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3812 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
document verification against the data sheets.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Maggie Li <maggie.li@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3811 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
0xe4 and 0xe5 registers. I'm suspecting that the documentation may be wrong.
Furthermore this fix for powernow may not work on CPUs hit by errata #181.
Workaround should be implemented. The powernow may not work on pre-A2 revisions
of VT8237S silicon, revision reg is unknown.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3795 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Joe Bao <zheng.bao@amd.com>
Reviewed-by: Maggie Li <maggie.li@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3786 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Joe Bao <zheng.bao@amd.com>
Reviewed-by: Maggie Li <maggie.li@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3785 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also, fix BIOS_CNTL, which is 0xdc on ICH7.
Build-tested with kontron/986lcd-m.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3733 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
ICH7 southbridge (but it might work with ICH4/ICH5 or so).
The ICH7 needs a different init code. Drop the non-working code for now.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3732 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
to only a set of reasonably similar ones, namely (for now) ICH0* - ICH6*,
and C-ICH.
All later ICH* southbridges (ICH7-ICH10) are _very_ different and were surely
not working with this driver anyway (and there's no chance to support
them reasonably with this driver without ending up in #ifdef hell).
ICH7 now has an extra driver in svn, whether ICH8-ICH10 are similar
enough to be supported by that ICH7 driver remains to be seen.
This patch was informally acked by Stefan Reinauer
<stepan@coresystems.de> on IRC.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3718 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Build-tested with the kontron/986lcd-m target.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3705 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This includes an early SMI handler.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3701 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also, use more readable #defines instead of hardcoded config ports for
PM/PM2 related functions, and simplify them a bit.
Build-tested with the AMD dbm690t target.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Marc Jones <marc.jones@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3680 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
build. As far as I know, no C7 boards currently in the tree use SPI
flash.
Signed-off-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3665 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
called from one target and that target is compiled with GCC, make the
function dependent on GCC.
ROMCC also chokes on the ULL suffix for integer constants. Change the
affected ones to UL for ROMCC compiled code.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3664 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
is also visible to ROMCC and ROMCC doesn't understand that.
The fix is to use __attribute__((packed)) only for gcc compiled code.
This has been unfixed for too long. There are more problems remaining,
but at least this one is solvable easily.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3660 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Build-tested with the AMD dbm690t board.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Marc Jones <marc.jones@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3655 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Marc Jones <marcj.jones@amd.com>
Acked-by: Marc Jones <marcj.jones@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3643 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
We shouldn't assume the presence of a working HDA codec, so put in
a reasonable timeout of 50usecs (timeout value borrowed from the kernel).
This makes SimNow work, since apparently though the codec is
present in Simnow, it is non functional.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3640 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Marc Jones <marc.jones@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3636 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
certainly won't build -- that comes later. I am hoping to get some
eyeballs on it for simple errors.
rs690 is next.
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3630 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
code to use it. That makes the code more readable and also less
error-prone.
Abuild tested.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3624 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Most of the functions in SB600 are enabled except power management.
Signed-off-by: Michael Xie <Michael.Xie@amd.com>
Reviewed-by: Marc Jones <marc.jones@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3589 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
All the PCIe slots are enabled in this patch except power management.
Signed-off-by: Michael Xie <Michael.Xie@amd.com>
Reviewed-by: Marc Jones <marc.jones@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3588 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
D1F0 bridge without activated I/O and MEM resources, otherwise it will hang
whole PCI bus.
U-boot is also disabling the IO/MEM decode when sizing the BARs, dont know why
does we not.
Second small change just changes a bit which controls the PSTATECTL logic.
Third change deals with the integrated VGA, which needs to be enabled early,
so the VGA_EN is set along the bridges, and PCI K8 resource maps are set
correctly. Finally the CPU accessible framebuffer is now disabled as it is not
needed.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3587 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
on mine desktop) except of reverting the small change introduced by Bari
(gpio/inta setup reg 0x5b). This should go for some board specific file. The
change would broke at least mine board. But seems to be needed for jakllsch.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Bari Ari <bari@onelabs.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3567 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
All devices work, no irq storms. Enjoy.
Signed-off-by: Bari Ari <bari@onelabs.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3556 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
and renames some existing macros for clarity.
Signed-off-by: Ed Swierk <eswierk@arastra.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3536 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
integrated LPC, SMBus, USB and SATA devices of the Intel EP80579
Integrated Processor.
Signed-off-by: Ed Swierk <eswierk@arastra.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3535 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Bari Ari <bari@onelabs.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3369 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
pci_write_config8.
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3282 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
for both serial ports, making it challenging to use COM2 for the early
console.
Enable the traditional I/O ranges 0x3f8 for COM1 and 0x2f8 for COM2.
Signed-off-by: Ed Swierk <eswierk@arastra.com>
Acked-by: Joseph Smith <joe@settoplinux.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3276 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
secondary controller was ok). There were two problems: the master sata
controller was not being initialized, and the irqs for the secondary ports on
both controllers were not being set in the mptable.
Thanks for Jonathan Kollasch for all the help figuring out the IRQ problem.
While all ports work reliably under a recent kernel (2.6.24), sata is about
half as fast as under the proprietary bios, according to bonnie++. That still
needs fixing...
Signed-off-by: Ward Vandewege <ward@gnu.org>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3253 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
It also keeps the boot processes from rebooting through out the coreboot process.
Signed-off-by: Joseph Smith <joe@smittys.pointclark.net>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3218 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
"off" in Config.lb should cause the PCI device not to respond to
configuration requests.
Replace the existing code that I naively copied from esb6300 with
something that actually works on the 3100.
Signed-off-by: Ed Swierk <eswierk@arastra.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3209 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Joseph Smith <joe@smittys.pointclark.net>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Ed Swierk <eswierk@arastra.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3208 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
There are no boards that use the i82801DB (ICH4). The code does NOT work.
Signed-off-by: Joseph Smith <joe@smittys.pointclark.net>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Ed Swierk <eswierk@arastra.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3206 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
pci_locate_device() to locate the SMBus controller and LPC bridge
devices on the PCI bus. Since these devices are always located at a
fixed PCI bus:device:function, the code can be simplified by
hardcoding the devices.
Signed-off-by: Ed Swierk <eswierk@arastra.com>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3205 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
the system automatically unless software resets the timer
periodically. The extra reboot extends boot time by several seconds.
The attached patch adds a function to the Intel 3100 southbridge code
that halts the TCO timer, thus preventing this extra reboot, and calls
the function early in the boot process on the Mt. Arvon board.
It also fixes a bug in the LPC device initialization -- the ACPI BAR
enable flag is bit 7, not bit 4.
Signed-off-by: Ed Swierk <eswierk@arastra.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3198 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
You can see this by executing commands like this:
grep -r pci_assign_irqs coreboot/src/*
This basically AMD/LX based boards: pcengines/alix1c,
digitallogic/msm800sev, artecgroup/dbe61, amd/norwich, amd/db800.
Also for AMD/GX1 based boards need a patch
[http://www.pengutronix.de/software/ptxdist/temporary-src/references/geode-5530.patch]
for the right IRQ setup.
AMD/GX1 based boards is: advantech/pcm-5820, asi/mb_5blmp, axus/tc320,
bcom/winnet100, eaglelion/5bcm, iei/nova4899r, iei/juki-511p.
I have two ideas.
1. Delete duplicate code from AMD/LX based boards.
2. Add IRQ routing for AMD/GX1 boards in coreboot.
The pirq.patch for IRQ routing logically consist from of two parts:
First part of pirq.patch independent from type chipsets and assign IRQ for
ever PCI device. It part based on AMD/LX write_pirq_routing_table() function.
Second part of pirq.patch depends of type chipset and set PIRQx lines
in interrupt router. This part supports only CS5530/5536 interrupt routers.
IRQ routing functionality is included through PIRQ_ROUTE in Config.lb.
Tested on iei/juki-511p(cs5530a), iei/pcisa-lx(cs5536) and also on
TeleVideo TC7020, see
http://www.coreboot.org/pipermail/coreboot/2007-December/027973.html.
Signed-off-by: Nikolay Petukhov <nikolay.petukhov@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3196 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The V-link setup and HT bridge is redone, because VT8237A has it in another
device. So far following combination of chipsets should now work:
K8T890CE + VT8237R
K8M890(CE) + VT8237R
VIA PC1 brige moved to NB code (vt8237r_bridge.c -> k8t890_bridge.c) and
notes about K8M890 support were added.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3183 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
max width of the link and also it will take the frequency of K8 HT
already done coreboot (and checks if t can run on it).
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3169 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
comments. Ripping out the ehci/uhci_init() code doesn't seem to have
done any harm, and I got rid of a bunch of unused junk in
i3100_smbus.h
I left the *_set_subsystem() arguments unsigned, as that's how the
function is declared in include/device/pci.h.
Signed-off-by: Ed Swierk <eswierk@arastra.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3157 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
flashes such as SST49LF080A: 1024K x8 (8 Mbit)
Tested on my system, the flash is found and if I use coreboot in second half it
works too.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3148 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
nVidia cards. The enable link should be enough, retrain is done there.
Tested on my system.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3147 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
a compiler warning.
Signed-off-by: Ronald Hoogenboom <hoogenboom30@zonnet.nl>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3115 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Don't enable pin0 for ioapic of io-4.
1. apic error in kernel for MB with mcp55+io55
2. some pcie-cards could have pci bridge there, so need to put entries
for device under them in mptable.
Signed-off-by: Yinghai Lu <yinghailu@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3112 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Due to the automatic nature of this update, I am self-acking. It worked in
abuild.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3053 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
code is changed.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3052 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Check that the SMBus controller is found and stop on an error.
Clean up and add additional path through the 8111 reset functions.
Signed-off-by: Marc Jones <marc.jones@amd.com>
Reviewed-by: Jordan Crouse <jordan.crouse@amd.com>
Acked-by: Myles Watson <myles@pel.cs.byu.edu>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3015 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Implement ISA related support:
- Initialize the RTC
- Enable access to all BIOS regions (but _not_ write access to ROM)
- Enable ISA (not EIO) support
- Without the *_isa.c file, the Super I/O init is never performed
- Improve IDE support:
- Add config option to enable Ultra DMA/33 for each disk
- Add config option to enable legacy IDE port access
- Implement hard reset support
- Implement USB controller support
- Various code cleanups and improvements
The code partially supports southbridges other than the 82371EB (but
which are very similar), more complete support will follow.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2994 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Use 'static' where appropriate.
- Use 'const' where appropriate.
- Indentation fixes.
- Add comment wrt init code which is only valid for VT8237R.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2974 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Upon incoming SMAF message from CPU (C3 or FID/VID change), the SB will
assert SLP# which is connected to LDTSTOP_L on K8 CPUs. Question is for how
long. Imho for 100us. Which is more than plenty (2us required) I will try
to justify this once I know what bios to set in SB.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2965 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
it to 8X transfer rate (up to 1066 MB/s) similar code placed here would be
needed for VT8237A/S etc. Using VIA recommended values despite they are for
K8T890CF, this is K8T890CE (still dont know what is exactly different).
This patch enables the parity error reporting on V-Link, so it enables NMI
generation for the SERR# errors. The NMI may not be generated, maybe port
61h needs some tuning too.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2958 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
i82801xx code for the following parts:
- AC97 audio/modem
- Onboard network interface cards (NICs)
- USB 1.1 controllers
- SMBus controllers
Some other parts are still missing and will be added later.
Use PCI ID #defines from pci_ids.h everywhere. Constify various structs.
Also, fix some random cosmetic issues in the code.
All of this is relatively trivial and tested by manually building
all boards which currently use the i82801xx code.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2951 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
ARRAY_SIZE() can be used on ROMCC-dependent systems. Also adds stdlib.h
to vt8237r_early_smbus.c, so it'll build on those systems.
Signed-off-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2949 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
(ICH/ICH0 up to the ICH9 family) in preparation for further
code improvements for the i82801xx southbridge code.
Small fixes in the 6300ESB PCI IDs.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2947 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
* Remove dead code
* Remove unused variables
* Fix bug where array was one element too small
* Fix error value truncation, the old code never entered the error path
* Remove warnings
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2945 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
ICH5/ICH5R (more to follow) in preparation of further 82801xx improvements.
Use human-readable names for the PCI ID #defines.
Rename *_ISA to *_LPC as per datasheet.
The 82801DBM only has 3 (not 4) USB devices, looks like a copy-paste error.
The fixes in southbridge code are only to keep the build working for now,
any real improvements will only go into the 82801xx code in future.
This is abuild-tested so it shouldn't break anything.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2938 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
the Jetway J7F2 patch that should be coming soon, and also moves most
defines into vt8237r.h. I've changed some of the values from u32 to u8,
because that's all they should ever need to be. Also includes
doxygenized comments!
Signed-off-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2937 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
No functional code changes.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2932 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2. Rename sisnb.c to sis761.c
3. Delete many mis-definition for sis device in
src/include/device/pci_ids.h
4. Trim trailing spaces for all files
Signed-off-by: Morgan Tsai <my_tsai@sis.com>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2931 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Joseph Smith <joe@smittys.pointclark.net>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2912 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: <corey.osgood@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2907 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
code. This is trivial, I did it for the other components before.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2905 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
southbridge now:
From: Morgan Tsai <my_tsai@sis.com>
It supports SiS761GX / SiS966 chipset, only for AMD K8 platform so far.
Due to integrated VGA sharing system memory, some code in southbridge
folder have to init northbridge.
Copyright (C) 2007 Morgan Tsai <my_tsai@sis.com>
Copyright (C) 2007 Silicon Integrated Systems Corp. (SiS)
Change Log:
Newly support GIGABYTE GA-2761GXDK
CPU type: AMD AM2 socket
Northbridge: SiS 761GX
Southbridge: SiS 966
SuperIO: ITE8716F
Signed-off-by: Morgan Tsai <my_tsai@sis.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2902 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
rodata.pci_driver" warnings are coming from? We were packing those
structures into a read-only segment, but forgot to mark them const.
Despite its size, this is a fairly trivial patch created by a simple
search/replace
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2891 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2883 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Painting the splash graphic is now ifdef'ed.
Signed-off-by: Juergen Beisert <juergen127@kreuzholzen.de>
Acked-by: Peter Stuge <peter@stuge.se>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2836 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
to set up one of five screen resolutions (sorry no autodetection at runtime,
resolution is selected at buildtime) and displays a graphic in the right
bottom corner (splash screen).
Signed-off-by: Juergen Beisert <juergen127@kreuzholzen.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2827 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
i82801DB to reset. See this thread for more info:
http://article.gmane.org/gmane.linux.bios/26791
Signed-off-by: Joseph Smith <joe@smittys.pointclark.net>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2816 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
fixes the problems with PCI add-on cards not being detected or
initialized on MCP55-based systems (PCI bridge decoding change).
I have tested this on the MSI MS-7260 (K9N Neo) with a PCI VGA card,
which worked fine in any of the three PCI slots.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2807 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Reported by Robert Millan.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2801 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This is tested with abuild so shouldn't break anything.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2800 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
For example: in C51/MCP55 or C51/MCP51
Will allow
1. C51 at 0x10 to 0x14, and MCP at 0 to 4
2. C51 at 1 to 4, and MCP at 7 to 0x0a
The reason is c51/mcp51/mcp55 reported unitid is 0x0f (far beyond it
needed), and will prevent us from putting them on bus 0.
Typical values for c51/mcp55 or c51/mcp51:
HT_CHAIN_UNITID_BASE = 0x10 # for C51
HT_CHAIN_END_UNITID_BASE = 0 # for mcp
If only have mcp with c51,
HT_CHAIN_UNITID_BASE = 0 # for MCP
#HT_CHAIN_END_UNITID_BASE = 0 # default value 0x20
Signed-off-by: Yinghai Lu <yinghai.lu@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2776 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
mostly undocumented, had a broken coding style, contained lots of dead
code and had several other problems, e.g. it enabled write access to the
ROM (why?), it unconditionally enabled primary/secondary IDE (which should
have a config option) and that even _twice_ (which is um... wrong).
The new code
- has 'ide0_enable' and 'ide1_enable' config options (which actually
work) to enable/disable the primary/secondary IDE interface in
Config.lb.
- Does _not_ enable write access to the ROM (or is there some good
reason to do that? If so, it should at least have a config option).
- Contains a bit more documentation.
- Uses readable (and documented) #defines instead of hardcoded magic values.
- aaand... it actually compiles ;-) Yep, that's right. The previous code
wouldn't even build, as it hadn't been fully ported from v1 (still used
v1 functions which are simply not available in v2).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2775 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2726 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
southbridges, along with the Asus MEW-VM. With this, my machine attempts to
boot linux, but does so very slowly and fails during the boot process, probably
because of the irq tables.
Signed-off-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Joseph Smith <joe@smittys.pointclark.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2719 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
return that skipped the disable code. This patch removes the return and
fixes the UART disable code.
The problem was that the disable code was ORing bits into the Legacy_IO
MSR causing issues with the LPC SIOs init code that would manifest as a
hang because the IO would not be decoded correctly. ANDing to clear the
bits fixes the issue.
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2706 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
In a mainboard's Config.lb file you can configure whether the primary
and/or secondary IDE interfaces shall be enabled.
Also, various fixups in the rest of the southbridge code, most notably
the early SMBus code, plus some documentation improvements.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Corey Osgood <corey_osgood@verizon.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2703 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
accessible (but not writable), so that reading/loading a payload
from that area can work (for instance).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2700 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
the new src/southbridge/amd/cs5536 code completely replaces it.
The Artecgroup dbe61 board currently uses it, but that is broken anyway
at the moment. A fix to use the new CS5536 code for it is being worked on.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2697 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Marc Jones <marc.jones@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2687 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Stefan Reinauer