Remove struct skylake_i2c_config from chip.h since it is not used
anymore.
Change-Id: Icde4b7af5b9c31020099c1a6372a6867827f61ae
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19520
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Board Scarlet doesn't use usbphy1.
BUG=b:37685249
TEST=boot Scarlet, check the firmware log, and confirm
no errors about USB1
Change-Id: I66e0d8a235cc9057964f7abca32bc692d41e88fd
Signed-off-by: Philip Chen <philipchen@google.com>
Reviewed-on: https://review.coreboot.org/19489
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
This patch currently contains the following -
1. Use SOC_INTEL_COMMON_BLOCK_FAST_SPI kconfig for common FAST_SPI code.
2. Perform FAST_SPI programming by calling APIs from common FAST_SPI library.
3. Use common FAST_SPI header file.
Change-Id: Ifd72734dadda541fe4c828e4f1716e532ec69c27
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/19080
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This patch currently contains the following -
1. Use SOC_INTEL_COMMON_BLOCK_FAST_SPI kconfig for common FAST_SPI code.
2. Perform FAST_SPI programming by calling APIs from common FAST_SPI library.
3. Use common FAST_SPI header file.
Change-Id: I4fc90504d322db70ed4ea644b1593cc0605b5fe8
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/19055
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
When using Wake On Voice &/or DCI, it requires xtal to be active during
low power idle.
With xtal being active in S0ix state power impact is 1-2 mW.
Hence set xtal bypass bit in CIR31C for low power idle entry.
TEST= Build with s0ix enable for Poppy. Boot to OS & verify that
bit 22 of CIR31C register is set. s0ix works.
Change-Id: Ide2d01536f652cd1b0ac32eede89ec410c5101cf
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/19442
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Create Intel Common FAST_SPI Controller code.
This code contains the code for SPI initialization which has
the following programming -
* Get BIOS Rom Region Size
* Enable SPIBAR
* Disable the BIOS write protect so write commands are allowed
* Enable SPI Prefetching and Caching.
* SPI Controller register offsets in the common header fast_spi.h
* Implement FAST_SPI read, write, erase APIs.
Change-Id: I046e3b30c8efb172851dd17f49565c9ec4cb38cb
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/18557
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Create Intel Common ITSS code. This code currently only contains
the code for Interrupt initialization required in Bootblock phase.
More code will get added up in the subsequent phases.
Change-Id: I133294188eb5d1312caeafcb621fb650a7fab371
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/19125
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The SRS bit which is supposed to indicate reset button press
is non-functional. If it did work the system reset event it
was associated with is overly specific. Therefore, use the
warm reset status bit.
BUG=b:37687843
Change-Id: I34dd09c03d2bca72da9a5cdf23121e0d0e621fa6
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/19484
Tested-by: build bot (Jenkins)
Reviewed-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
It's come to attention that apollolake doesn't support a full retrain
on warm reset. Therefore force a cold reset when a full retrain is
requested in the non-S5 path.
BUG=b:37687843
Change-Id: If9a3de1fa8760e7bb2f06eef93a0deb9dbd3f047
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/19483
Tested-by: build bot (Jenkins)
Reviewed-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Update default ODT config to have correct CA ODT settings as the
current defaults are incorrect for all the current apollolake designs.
All the current designs pull both A and B channels' LPDDR4 modules' ODT
pins to 1.1V. Therefore, the correct impedance setting needs to be
applied.
In order for the settings to take effect one needs to clear the
memory training cache in deployed systems. Trigger this by bumping
the memory setting version for the SoC.
If needed in the future support for allowing the override of this
setting from the mainboard should be straight forward. It's just not
necessary at this time.
BUG=b:37687843
TEST=BAT test, warm, reboot, S3 cycle test
Change-Id: I9a2f7636b46492a9d08472a0752cdf1f86a72e15
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/19397
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
BUG=b:35647967
TEST=boot from bob
Change-Id: I5de902ab26fe768b641f69d85a5294baf6d916e3
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 223257d486b026c06a1f3a7a830b829efb9932dc
Original-Change-Id: I055ad5f59285cee3110d1e7cb1a53a60144712e4
Original-Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/452285
Original-Commit-Ready: Caesar Wang <wxt@rock-chips.com>
Original-Tested-by: Caesar Wang <wxt@rock-chips.com>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/19433
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Add basic SMM support for Broadwell-DE SoC.
The code is mainly based on the SMM implementation of Broadwell with a
few differences:
- EMRR is now called PRMRR and the UNCORE part of it is not available
- SMM_FEATURE_CONTROL is no longer a MSR but is now located in PCI space
- currently only SERIRQ-SMI has a handler
Change-Id: I461a14d411aedefdb0cb54ae43b91103a80a4f6a
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/19145
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
On Apollo Lake it was discovered that our current FADT implementation is
valid for ACPI version 3.0 but misses fields for ACPI version 5.0. We
run into booting issues with Windows 10 using version 5 in the FADT
header. In commit 2b8552f49bc3a7d0290f96a84b573669de396011
(intel/apollolake: Switch FADT to ACPI version 3.0) we go back to
version 3 for Apollo Lake. Skylake is now the last platform that uses
version 5 in FADT header.
Change-Id: I2d0367fae5321dee4ccac417b7f99466f8973577
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/19453
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The current implementation of the FADT structure is only ACPI 3.0 compliant.
Setting the version to ACPI 5.0 results in a corrupt FADT. Linux seems
to be able to deal with it but Windows 10 hangs in a really early stage
without any notification to the user.
If ACPI 5.0 is mandatory, the FADT structure needs to be adjusted to
match the specification. Therefore the members sleep_ctl and sleep_stat
needs to be added to FADT structure.
Change-Id: I51c7a7a84d10283f5c2a8a2c57257d53bbdee7ed
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/19146
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
MMA blobs are SOC specific (not board). So far MMA
is supported by big cores (SKL and KBL).
Change-Id: I922789a2a12d55360624dd6de15ab9f0bb5f0acf
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/19260
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
These files are actually indentical, but unfortunately, the formatting
was changed without caring for the already present files. Fix that. Use
the license formatting where less lines are used.
The next step is to put that in a common location.
Change-Id: Iecb263b9d321a33e64988b315220893df2e0045c
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: https://review.coreboot.org/19423
Tested-by: build bot (Jenkins)
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Utilize the postcar stage for tearing down CAR and initializing
the MTRRs once ram is up. This flow is consistent with apollolake
and allows CAR_GLOBAL variables to be directly accessed and no
need for migrating CAR_GLOBAL variables as romstage doesn't
run with and without CAR being available.
Change-Id: I76de447710ae1d405886eb9420dc4064aa26eccc
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/19335
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
The devicetree data structures have been available in more than just
ramstage and romstage. In order to provide clearer and consistent
semantics two new macros are provided:
1. DEVTREE_EARLY which is true when !ENV_RAMSTAGE
2. DEVTREE_CONST as a replacment for ROMSTAGE_CONST
The ROMSTAGE_CONST attribute is used in the source code to mark
the devicetree data structures as const in early stages even though
it's not just romstage. Therefore, rename the attribute to
DEVTREE_CONST as that's the actual usage. The only place where the
usage was not devicetree related is console_loglevel, but the same
name was used for consistency. Any stage that is not ramstage has
the const C attribute applied when DEVTREE_CONST is used.
Change-Id: Ibd51c2628dc8f68e0896974f7e4e7c8588d333ed
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/19333
Tested-by: build bot (Jenkins)
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The MT817x display output pipeline can be configured to drive an 8-lane
MIPI/DSI panel using "dual DSI" mode. For the "dual DSI" video data path,
the UFO block is configured to reorder the data stream into left and right
halves which are then sent by the SPLIT1 block to the DSI0 and DSI1
respectively. The DSI0 and DSI1 outputs are then synchronously clocked at
half the nominal data rate by their respective MIPI_TX0/MIPI_TX1 phys.
Also, update the call sites in oak mainboard to avoid build breakage.
BRANCH=none
BUG=b:35774871
TEST=Boot Rowan in developer mode and see output on the panel
Change-Id: Id47dfd7d9e98689b54398fc8d9142336b41dc29f
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19361
Tested-by: build bot (Jenkins)
Reviewed-by: Julius Werner <jwerner@chromium.org>
This patch enables TPM2 using cr50 over I2C for the Rowan board, and
adds an mt8173 specific TPM IRQ polling function. The function relies on
the appropriate EINT input configured to trigger the ready status on
the rising edge.
The cr50 TPM is on I2C address 0x50.
The cr50 interrupt GPIO is also made available for use by depthcharge
via the coreboot tables.
BRANCH=none
BUG=b:36786804
TEST=Boot rowan w/ serial enabled, verify coreboot and depthcharge are
configured to use IRQ flow control when talking to the Cr50 TPM.
Change-Id: If6cdd0e39e4ac86538f27f322c55c329179ee084
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19364
Tested-by: build bot (Jenkins)
Reviewed-by: Julius Werner <jwerner@chromium.org>
Add basic support to configure GPIOs to poll for external interrupts
(EINT).
BRANCH=none
BUG=b:36786804
TEST=Boot rowan w/ serial enabled, verify coreboot and depthcharge are
configured to use IRQ flow control when talking to the Cr50 TPM.
Change-Id: I9d52591661a5a74ec1fd9a081f606f0a08a3a6ab
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-on: https://review.coreboot.org/19362
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins)
On Intel platforms utilizing the CR50 TPM the interrupts are routed
to GPIOs connected to the GPE blocks. Therefore, provide a common
implementation for tis_plat_irq_status() to reduce code duplication.
This code could be further extended to not be added based on
MAINBOARD_HAS_TPM_CR50, but that's all that's using it for now.
Change-Id: I955df0a536408b2ccd07146893337c53799e243f
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/19369
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins)
Move include of reg_access.h from pci_devs.h to reg_access.c.
TEST=Build and run on Galileo Gen2
Change-Id: I0d2de96f51c56001cdd06c7974cbc649fde1e89c
Signed-off-by: Lee Leahy <Leroy.P.Leahy@intel.com>
Reviewed-on: https://review.coreboot.org/19355
Tested-by: build bot (Jenkins)
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Add ASL entries for IMGU and CIO2 devices
* _CCA ACPI object to report that there is no Cache Coherent DMA support.
* CAMD ACPI object to specify the device type.
These ACPI objects are used by Intel kernel drivers.
BUG=b:36580624
BRANCH=none
TEST=Build and boot poppy. Dump and verify that DSDT table
has the entries for IMGU and CIO2 devices.
Change-Id: I13050253e18408cdb1e196f8003b3f43299aa5a5
Signed-off-by: Sowmya V <v.sowmya@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/18968
Tested-by: build bot (Jenkins)
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
With recent change to use common block PCR (ccd8700c),
IOSF_BASE_ADDRESS was renamed to PCR_BASE_ADDRESS. However, SD card
change (99ce8a9b) was not rebased on top of it, so IOSF_BASE_ADDRESS
slipped into the tree. Fix this by replacing all occurrences of
IOSF_BASE_ADDRESS by PCR_BASE_ADDRESS.
Change-Id: I40eb07be306035c940fc960896e0807d6c73bafa
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19277
Tested-by: build bot (Jenkins)
Reviewed-by: Venkateswarlu V Vinjamuri <venkateswarlu.v.vinjamuri@intel.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Currently sdcard CD host ownership is always owned by the GPIO driver.
Due to this sdcard detection fails during initial boot process and OS
fails to boot from sdcard.
This implements change in host ownership from acpi to GPIO driver when
kernel starts booting.
BUG=b:35648535
TEST=Check OS boot from sdcard.
Change-Id: I042a8762dc1f9cb73e6a24c1e7169c9746b2ee14
Signed-off-by: Venkateswarlu Vinjamuri <venkateswarlu.v.vinjamuri@intel.com>
Reviewed-on: https://review.coreboot.org/18947
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Vaibhav Shankar <vaibhav.shankar@intel.com>
Currently when enabling Deep S3 or Deep S5 it unconditionally gets enabled
in both DC and AC states. However since using Deep S3 disables some
expected features like wake-on-USB it is not always desired to enable the
same state in both modes.
To address this split the setting and add a separate config for Deep Sx in
AC and DC states.
All motherboards that set this config were updated, but there is no actual
change in behavior in this commit.
BUG=b:36723679
BRANCH=none
TEST=This commit has no runtime visible changes, I verified on Eve that the
Deep SX config registers are unchanged, and it compiles for all affected boards.
Change-Id: I590f145847785b5a7687f235304e988888fcea8a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/19239
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Use lpss common library to program reset and
clock register for lpss modules
Change-Id: I75f9aebd60290fbf22684f8cc2ce8e8a4a4304b0
Signed-off-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-on: https://review.coreboot.org/19154
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Create Intel Common RTC code. This code currently only
contains the code for configuring RTC required in Bootblock phase
which has the following programming -
* Enable upper 128 bytes of CMOS.
Change-Id: Id9dfcdbc300c25f43936d1efb5d6f9d81d3c8453
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/18558
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Tested-by: build bot (Jenkins)
This patch use common PCR library to perform CRRd and CRWr operation
using Port Ids, define inside soc/pcr_ids.h
Change-Id: Iacbf58dbd55bf3915676d875fcb484362d357a44
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/18673
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch use common PCR library to perform CRRd and CRWr operation
using Port Ids, define inside soc/pcr_ids.h
Change-Id: Id9336883514298e7f93fbc95aef8228202aa6fb9
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/18674
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
IOSF_SB message space is used to access registers mapped
on IOSF-SB. These registers include uncore CRs (configuration
registers) and chipset specific registers. The Private
Configuration Register (PCR) space is accessed on IOSF-SB
using destination ID also known as Port ID.
Access to IOSF-SB by the Host or System Agent is possible
over PSF via the Primary to Sideband Bridge (P2SB). P2SB will
forward properly formatted register access requests as CRRd and
CRWr request via IOSF-SB.
Change-Id: I78526a86b6d10f226570c08050327557e0bb2c78
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/18669
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
There is only one user for spi_get_config i.e. SPI ACPI. Also, the
values provided by spi_get_config are constant for now. Thus, get rid
of the spi_get_config call and fill in these constant values in SPI
ACPI code itself. If there is a need in the future to change these,
appropriate device-tree configs can be added.
BUG=b:36873582
Change-Id: Ied38e2670784ee3317bb12e542666c224bd9e819
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19203
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Enable SS link trunk clock gating & D3hot when device enters
D3 state.
Similarly disable SS link trunk clock gating & D3hot when device enters
D0 state
TEST=Build & boot Poppy board. Check working for XHCI wake when DUT
is in S3.
Change-Id: Ida2afa2e5f9404c0c15d7027480a28a003ad9a40
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/18879
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Sky Lake PCH contains two GSPI controllers. Using the common GSPI
controller driver implementation for Intel PCH, add support for GSPI
controller buses on Sky Lake/Kaby Lake.
BUG=b:35583330
Change-Id: I29b1d4d5a6ee4093f2596065ac375c06f17d33ac
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19099
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Add support for GSPI controller in Intel PCH. This controller is
compliant with PXA2xx SPI controller with some additional registers to
provide more fine-grained control of the SPI bus. Currently, DMA is
not enabled as this driver might be used before memory is up (e.g. TPM
on SPI).
Also, provide common GSPI config structure that can be included by
SoCs in chip config to allow mainboards to configure GSPI
bus. Additionally, provide an option for SoCs to configure BAR for
GSPI controllers before memory is up.
BUG=b:35583330
Change-Id: I0eb91eba2c523be457fee8922c44fb500a9fa140
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19098
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Since there are multiple controllers in the LPSS and all use the same
frequency, provide a single Kconfig option for LPSS_CLOCK_MHZ.
BUG=b:35583330
Change-Id: I3c0cb62d56916e6e5f671fb5f40210f4cb33316f
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19115
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
This is required to provide tsc freq required by timer library.
BUG=b:35583330
TEST=Verified that delay(5) in verstage adds a delay of 5 seconds.
Change-Id: I03edebe394522516b46125fae1a17e9a06fd5f45
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/19094
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
When using rise_time_ns and fall_time_ns there's currently not
a way to specify a target data hold time. The internal 300ns
value is used. However, that isn't always sufficient depending on
bus topology. Therefore, provide the ability to specify data
hold time in ns from devicetree, defaulting to default value if
none are specified.
BUG=b:36469182
Change-Id: I86de095186ee396099709cc8a97240bd2f9722c9
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/19064
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
In builds without CONFIG_VBOOT_SEPARATE_VERSTAGE, verstage files are
linked directly into the bootblock or the romstage. However, they're
still compiled with a separate "libverstage" source file class, linked
into an intermediate library and then linked into the final destination
stage.
There is no obvious benefit to doing it this way and it's unclear why it
was chosen in the first place... there are, however, obvious
disadvantages: it can result in code that is used by both libverstage
and the host stage to occur twice in the output binary. It also means
that libverstage files have their separate compiler flags that are not
necessarily aligned with the host stage, which can lead to weird effects
like <rules.h> macros not being set the way you would expect. In fact,
VBOOT_STARTS_IN_ROMSTAGE configurations are currently broken on x86
because their libverstage code that gets compiled into the romstage sets
ENV_VERSTAGE, but CAR migration code expects all ENV_VERSTAGE code to
run pre-migration.
This patch resolves these problems by removing the separate library.
There is no more difference between the 'verstage' and 'libverstage'
classes, and the source files added to them are just treated the same
way a bootblock or romstage source files in configurations where the
verstage is linked into either of these respective stages (allowing for
the normal object code deduplication and causing those files to be
compiled with the same flags as the host stage's files).
Tested this whole series by booting a Kevin, an Elm (both with and
without SEPARATE_VERSTAGE) and a Falco in normal and recovery mode.
Change-Id: I6bb84a9bf1cd54f2e02ca1f665740a9c88d88df4
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/18302
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch attempts to finish the separation between CONFIG_VBOOT and
CONFIG_CHROMEOS by moving the remaining options and code (including
image generation code for things like FWID and GBB flags, which are
intrinsic to vboot itself) from src/vendorcode/google/chromeos to
src/vboot. Also taking this opportunity to namespace all VBOOT Kconfig
options, and clean up menuconfig visibility for them (i.e. some options
were visible even though they were tied to the hardware while others
were invisible even though it might make sense to change them).
CQ-DEPEND=CL:459088
Change-Id: I3e2e31150ebf5a96b6fe507ebeb53a41ecf88122
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/18984
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This callback was only required for a single mainboard, and it can
easily be moved to mainboard-specific code. This patch removes it from
the global namespace and isolates it to the Jecht board. (This makes
it easier to separate vboot and chromeos code in a later patch.)
Change-Id: I9cf67a75a052d1c86eda0393b6a9fbbe255fedf8
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/18981
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
The virtualized developer switch was invented five years ago and has
been used on every vboot system ever since. We shouldn't need to specify
it again and again for every new board. This patch flips the Kconfig
logic around and replaces CONFIG_VIRTUAL_DEV_SWITCH with
CONFIG_PHYSICAL_DEV_SWITCH, so that only a few ancient boards need to
set it and it fits better with CONFIG_PHYSICAL_REC_SWITCH. (Also set the
latter for Lumpy which seems to have been omitted incorrectly, and hide
it from menuconfig since it's a hardware parameter that shouldn't be
configurable.)
Since almost all our developer switches are virtual, it doesn't make
sense for every board to pass a non-existent or non-functional developer
mode switch in the coreboot tables, so let's get rid of that. It's also
dangerously confusing for many boards to define a get_developer_mode()
function that reads an actual pin (often from a debug header) which will
not be honored by coreboot because CONFIG_PHYSICAL_DEV_SWITCH isn't set.
Therefore, this patch removes all those non-functional instances of that
function. In the future, either the board has a physical dev switch and
must define it, or it doesn't and must not.
In a similar sense (and since I'm touching so many board configs
anyway), it's annoying that we have to keep selecting EC_SOFTWARE_SYNC.
Instead, it should just be assumed by default whenever a Chrome EC is
present in the system. This way, it can also still be overridden by
menuconfig.
CQ-DEPEND=CL:459701
Change-Id: If9cbaa7df530580a97f00ef238e3d9a8a86a4a7f
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/18980
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
VBOOT_DYNAMIC_WORK_BUFFER and VBOOT_STARTS_IN_ROMSTAGE are equivalent in
practice. We can't have a dynamic work buffer unless we start in/after
romstage, and there'd be no reason to go with a static buffer if we do.
Let's get rid of one extra option and merge the two.
Change-Id: I3f953c8d2a8dcb3f65b07f548184d6dd0eb688fe
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/18979
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
CHIPSET_PROVIDES_VERSTAGE_MAIN_SYMBOL allows the SoC directory to
provide its own main() symbol that can execute code before the generic
verstage code runs. We have now established in other places (e.g. T210
ramstage) a sort of convention that SoCs which need to run code in any
stage before main() should just override stage_entry() instead. This
patch aligns the verstage with that model and gets rid of the extra
Kconfig option. This also removes the need for aliasing between main()
and verstage(). Like other stages the main verstage code is now just in
main() and can be called from stage_entry().
Change-Id: If42c9c4fbab51fbd474e1530023a30b69495d1d6
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/18978
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Some Chrome OS boards previously didn't have a hardcoded vboot
configuration (e.g. STARTS_IN_BOOTBLOCK/_ROMSTAGE, SEPARATE_VERSTAGE,
etc.) selected from their SoC and mainboard Kconfig files, and instead
relied on the Chrome OS build system to pass in those options
separately. Since there is usually only one "best" vboot configuration
for a certain board and there is often board or SoC code specifically
written with that configuration in mind (e.g. memlayout), these options
should not be adjustable in menuconfig and instead always get selected
by board and SoC Makefiles (as opposed to some external build system).
(Removing MAINBOARD_HAS_CHROMEOS from Urara because vboot support for
Pistachio/MIPS was never finished. Trying to enable even post-romstage
vboot leads to weird compiler errors that I don't want to track down
now. Let's stop pretending this board has working Chrome OS support
because it never did.)
Change-Id: Ibddf413568630f2e5d6e286b9eca6378d7170104
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/19022
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch currently contains the SA initialization
required for bootblock phase -
1. Use SOC_INTEL_COMMON_BLOCK_SA kconfig for common SA code.
2. Perform PCIEXBAR programming based on soc configurable
PCIEX_LENGTH_xxxMB
3. Use common systemagent header file.
Change-Id: I01a24e2d4f1c8c9ca113c128bb6b3eac23dc79ad
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/18567
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
This patch currently contains the SA initialization
required for bootblock phase -
1. Use SOC_INTEL_COMMON_BLOCK_SA kconfig for common SA code.
2. Perform PCIEXBAR programming based on soc configurable
PCIEX_LENGTH_xxxMB
3. Use common systemagent header file.
Change-Id: I0fa0a60f680b9b00b7f26f1875c553612b123a8e
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/18566
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Create common Intel systemagent code.
This code currently contains the SA initialization
required in Bootblock phase, which has the following programming-
* Set PCIEXBAR
* Clear TSEG register
More code will get added up in the subsequent phases.
Change-Id: I6f0c515278f7fd04d407463a1eeb25ba13639f5c
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/18565
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch to make common PCI device name between APL and SKL.
Change-Id: I5e4c7502e9678c0a367e9c7a96cf848d5b24f68e
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/18576
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
This patch currently contains common CAR initialization
required in bootblock phase along with common MSR header -
1. Use SOC_INTEL_COMMON_BLOCK_CAR to have common CAR initialization
and CAR teardown.
2. Use common MSR header "intelblocks/msr.h" inside soc/cpu.h
Change-Id: I67f909f50a24f009b3e35388665251be1dde40f7
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/18555
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Create sample model for common car init and teardown programming.
TEST=Booted Reef, KCRD/EVE, GLKRVP with CAR_CQOS, CAR_NEM_ENHANCED
and CAR_NEM configs till post code 0x2a.
Change-Id: Iffd0c3e3ca81a3d283d5f1da115222a222e6b157
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/18381
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Replace the use of the old device_t definition inside
soc/intel/fsp_baytrail.
Change-Id: I2791346289c04049e6f032c8e120e4be9ba6657f
Signed-off-by: Antonello Dettori <dev@dettori.io>
Reviewed-on: https://review.coreboot.org/17319
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Also move all local variable declaration at starting of function
block.
Change-Id: I774485a23b4b7d96a8dbd837da45553251dff3b0
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/18949
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch implements SGX initialization steps in coreboot per Intel SGX
BWG rev 2.0.8 for Kaby Lake SoC. If enabled on a Kabylake device, SoC
capability and PRM (processor reserved memory) of desired size (needs to
be configured through PrmrrSize) are provisioned for later software
stack to use SGX (i.e., run SGX enclaves).
One issue is still puzzling and needs to be addressed: by calling
configure_sgx() in cpu_core_init() which is the per-thread function, SGX
is always failing for thread 0 but is successful for other 3 threads.
I had to call configure_sgx() again from soc_init_cpus() which is the
BSP-only function to make it enable on the BSP.
Another pending work is the implementation for the Owner Epoch update
which shall be added later.
BUG=chrome-os-partner:62438
BRANCH=NONE
TEST=Tested on Eve, verified SGX activation is successful on all threads.
Change-Id: I8b64284875eae061fa8e7a01204d48d320a285a9
Signed-off-by: Robbie Zhang <robbie.zhang@intel.com>
Reviewed-on: https://review.coreboot.org/18445
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
FSP disables host access to shadowed PMC XRAM registers by default,
it also provides a UPD to enable/disable host reads to these regiters.
Expose the same in devicetree as a config option.
Change-Id: Iaa33aa3233bda4f050da37d1d8af0556311c9496
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/18319
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Extract SMBIOS memory information from FSP SMBIOS_MEM_INFO_HOB
and use common function dimm_info_fill() to save it in CBMEM.
BUG=chrome-os-partner:61729
BRANCH=none
TEST=Build and boot Reef to verify the type 17 DIMM info coming in
SMBIOS table from Kernel command "dmidecode".
Change-Id: I33c3a0bebf33c53beadd745bc3d991e1e51050b7
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/18451
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Pratikkumar V Prajapati <pratikkumar.v.prajapati@intel.com>
Fix the following error and warnings detected by checkpatch.pl:
ERROR: switch and case should be at the same indent
WARNING: line over 80 characters
WARNING: storage class should be at the beginning of the declaration
WARNING: adding a line without newline at end of file
WARNING: __func__ should be used instead of gcc specific __FUNCTION__
WARNING: Comparisons should place the constant on the right side of the test
TEST=None
Change-Id: I85c400e4a087996fc81ab8b0e5422ba31df3c982
Signed-off-by: Lee Leahy <Leroy.P.Leahy@intel.com>
Reviewed-on: https://review.coreboot.org/18885
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Fix the following errors and warnings detected by checkpatch:
ERROR: open brace '{' following struct go on the same line
ERROR: return is not a function, parentheses are not required
ERROR: do not use assignment in if condition
ERROR: trailing statements should be on next line
WARNING: else is not generally useful after a break or return
WARNING: braces {} are not necessary for single statement blocks
WARNING: braces {} are not necessary for any arm of this statement
TEST=None
Change-Id: I9414341b0c778c252db33f0ef4847b9530681d96
Signed-off-by: Lee Leahy <Leroy.P.Leahy@intel.com>
Reviewed-on: https://review.coreboot.org/18884
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Fix the following issue detected by checkpatch:
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
TEST=None
Change-Id: Iae22e724b6adae16248db7dc8f822f65bfadae5f
Signed-off-by: Lee Leahy <Leroy.P.Leahy@intel.com>
Reviewed-on: https://review.coreboot.org/18873
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Fix the following errors and warnings detected by checkpatch.pl:
ERROR: code indent should use tabs where possible
ERROR: space required after that ',' (ctx:VxV)
ERROR: space prohibited before that ',' (ctx:WxW)
ERROR: spaces required around that '=' (ctx:VxV)
ERROR: spaces required around that '<=' (ctx:WxV)
ERROR: spaces required around that '<=' (ctx:VxV)
ERROR: spaces required around that '>' (ctx:VxV)
ERROR: spaces required around that '>=' (ctx:VxV)
ERROR: spaces required around that '+=' (ctx:VxV)
ERROR: spaces required around that '<' (ctx:VxV)
ERROR: "foo * bar" should be "foo *bar"
ERROR: "foo* bar" should be "foo *bar"
ERROR: "(foo*)" should be "(foo *)"
ERROR: space required before the open parenthesis '('
WARNING: space prohibited between function name and open parenthesis '('
WARNING: please, no space before tabs
WARNING: please, no spaces at the start of a line
False positives are generated for the following test:
WARNING: space prohibited between function name and open parenthesis '('
in both pei_data.h and pei_wrapper.h
TEST=None
Change-Id: Icab08e5fcb6d5089902ae5ec2aa5bbee5ac432ed
Signed-off-by: Lee Leahy <Leroy.P.Leahy@intel.com>
Reviewed-on: https://review.coreboot.org/18872
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
eMMC Controller is taking over 100ms to resume during runtime which
results in I/O latency issues on the Apollo Lake system such as Snappy.
The cause is the Linux Kernel setting the firmware reset time to
100 ms by default.
This patch adds _DSM method for eMMC comtroller for specifying the
device readiness durations. Function index 9 returns package of five
integers to set D3 cold delay to zero and ACPI constant Ones for the
elements where overriding the default values is not desired.
BUG=b:35774937
BRANCH=none
TEST=update snappy coreboot and test i/o latency is under 100ms
Signed-off-by: Zhuo-hao Lee <zhuo-hao.lee@intel.com>
Signed-off-by: Sowmya V <v.sowmya@intel.com>
Change-Id: Idcfe4252b20bead15c2e5b9cb000ff797295f06a
Reviewed-on: https://review.coreboot.org/18806
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Fix the following errors and warnings detected by checkpatch.pl:
ERROR: that open brace { should be on the previous line
ERROR: return is not a function, parentheses are not required
WARNING: braces {} are not necessary for any arm of this statement
WARNING: line over 80 characters
WARNING: braces {} are not necessary for single statement blocks
WARNING: Avoid unnecessary line continuations
WARNING: break is not useful after a goto or return
WARNING: else is not generally useful after a break or return
False positives are generated by checkpatch for the following test:
ERROR: Macros with complex values should be enclosed in parentheses
TEST=Build for cyan
Change-Id: I19048895145b138a63100b29f829ff446ff71b58
Signed-off-by: Lee Leahy <Leroy.P.Leahy@intel.com>
Reviewed-on: https://review.coreboot.org/18871
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins)
Fix the following warning detected by checkpatch.pl:
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
TEST=Build for cyan
Change-Id: Ib5c6a1bf5308a8add42d7371854b80ea53d7ae84
Signed-off-by: Lee Leahy <Leroy.P.Leahy@intel.com>
Reviewed-on: https://review.coreboot.org/18870
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins)
Fix the following errors and warnings detected by checkpatch.pl:
ERROR: space required after that ',' (ctx:VxV)
ERROR: space prohibited before that ',' (ctx:WxE)
ERROR: spaces required around that '=' (ctx:WxV)
ERROR: code indent should use tabs where possible
WARNING: space prohibited between function name and open parenthesis '('
WARNING: please, no spaces at the start of a line
TEST=Build for cyan
Change-Id: I84d4204585b498b695608c5008fdfb7961e2416f
Signed-off-by: Lee Leahy <Leroy.P.Leahy@intel.com>
Reviewed-on: https://review.coreboot.org/18869
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins)
Fix the following errors and warnings detected by checkpatch.pl:
ERROR: code indent should use tabs where possible
ERROR: Macros with complex values should be enclosed in parentheses
ERROR: "foo * bar" should be "foo *bar"
ERROR: space required before the open parenthesis '('
ERROR: spaces required around that '=' (ctx:VxW)
WARNING: space prohibited between function name and open parenthesis '('
WARNING: storage class should be at the beginning of the declaration
WARNING: char * array declaration might be better as static const
WARNING: please, no space before tabs
WARNING: braces {} are not necessary for single statement blocks
WARNING: else is not generally useful after a break or return
WARNING: static const char * array should probably be static const char * const
TEST=Build for glados
Change-Id: Ic14ca3abd193cfe257504a55ab6b74782b26bf6d
Signed-off-by: Lee Leahy <Leroy.P.Leahy@intel.com>
Reviewed-on: https://review.coreboot.org/18868
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Fix the following warning detected by checkpatch:
WARNING: line over 80 characters
TEST=Build for glados
Change-Id: I79341f46ca06ac052f987975ccaf975470d27806
Signed-off-by: Lee Leahy <Leroy.P.Leahy@intel.com>
Reviewed-on: https://review.coreboot.org/18867
Tested-by: build bot (Jenkins)
Reviewed-by: Lee Leahy <leroy.p.leahy@intel.com>
Fix the following warning detected by checkpatch.pl:
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
TEST=Build for glados
Change-Id: Idc2ad265e8ed8cd7fd6d228cfbe4cbbcb9d3ebfc
Signed-off-by: Lee Leahy <Leroy.P.Leahy@intel.com>
Reviewed-on: https://review.coreboot.org/18866
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Add options to set the AC and DC loadline values for each supported
VR type so these can be tuned on a per-board basis in devicetree.cb.
BUG=b:36228330
BRANCH=none
TEST=Build and boot on Eve and check debug FSP output to ensure that
it is applying the provided loadline values
Change-Id: I2a5533d2c9fd86351c86584e3738e80ac4c1f915
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18819
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
With the move to FSP 2.0 the number of VR types supported was
reduced to 4, and the VR_RING type is no longer present.
This means all existing boards using FSP 2.0 are incorrectly
passing VR configuration into FSP as the values corresponding to
"GT Sliced" and "GT Unsliced" have changed.
Fix this by updating the skylake SOC VR handling to account for
changes in the FSP configuration and no longer provide VR_RING
type when using FSP 2.0.
BUG=b:36228330
BRANCH=none
TEST=manual: build and boot on Eve
Change-Id: I59eea9fba006a4c235d7b42d07fdc6e4f44f7351
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18818
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
Add support for describing the NHLT blob for the rt5514 DSP.
Currently this only supports 4 channel capture.
BUG=b:35585307
BRANCH=none
TEST=build and boot on Eve P1
Change-Id: Ib59b56222f9aa65370fdcf9ddf25145c571b1b2e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18816
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Always read the rmu.bin file from the read-only section of the SPI
flash. Without this change vboot attempts to read this file from the
A or B section of the flash.
TEST=Build and run on Galileo Gen2
Change-Id: Ied8eaa2cd37645bf401aa957936943946bfd6182
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/18803
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Fix the following error detected by checkpatch.pl:
ERROR: code indent should use tabs where possible
TEST=Build and run on Galileo Gen2
Change-Id: Ief4b96073b3df30e45bf5d802ca3b190e7f431a7
Signed-off-by: Lee Leahy <Leroy.P.Leahy@intel.com>
Reviewed-on: https://review.coreboot.org/18753
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Since asking CSE to read FPF status turned out to be slow in some
cases, cache and save returned value on first boot only. Value is
read from flash on consequent boots.
BUG=b:35586975
BRANCH=reef
TEST=boot twice, make sure cached FPF status is loaded from
flash the second time.
Change-Id: I6e56a35407c9097616ccb05a557fded7b639c88a
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/18774
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Fix build error with FSP 1.1. Pass the S3 wake status to
fsp_silicon_init.
TEST=Build and run on Galileo Gen2
Change-Id: I78150f737321db5b1b4d63b411fa6432ac30d080
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/18805
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Return NULL for top_of_memory when the register has not been set.
TEST=Build and run on Galileo Gen2
Change-Id: If79cac68c2a64aa9bf3be72d3cfc4c73fceef12b
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/18802
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Extract SMBIOS memory information from FSP SMBIOS_MEM_INFO_HOB
and save it in CBMEM.
BUG=chrome-os-partner:61729
BRANCH=none
TEST=Build and boot KBLRVP to verify the type 17 DIMM info coming in
SMBIOS Table from Kernel command "dmidecode".
Change-Id: I593d4ccb0d4866e99913a73c49b2f000b51827d1
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/18275
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add the files to support verstage for vboot.
TEST=Build and run on Galileo Gen2
Change-Id: Icf87075012c08cf581c17d579e0763888c707265
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/18040
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Fix the following warning detected by checkpatch.pl:
WARNING: line over 80 characters
TEST=Build for reef
Change-Id: I4fbe95037ca4b52e64ba37e5c739af4a03f64feb
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/18728
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Fix the following errors and warnings detected by checkpatch.pl:
ERROR: switch and case should be at the same indent
ERROR: do not use assignment in if condition
WARNING: Statements terminations use 1 semicolon
WARNING: unnecessary whitespace before a quoted newline
WARNING: else is not generally useful after a break or return
TEST=Build for reef
Change-Id: I5486936dbf19b066c76179d929660affa1da5f16
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/18727
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Fix the following error and warning detected by checkpatch.pl:
ERROR: inline keyword should sit between storage class and type
WARNING: storage class should be at the beginning of the declaration
TEST=Build for reef
Change-Id: I2ed418cc3b4a989eb1101013944169429bf147c2
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/18726
Tested-by: build bot (Jenkins)
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Fix the following errors and warning detected by checkpatch.pl:
ERROR: space required before the open parenthesis '('
ERROR: space prohibited before that close parenthesis ')'
ERROR: return is not a function, parentheses are not required
WARNING: space prohibited between function name and open parenthesis '('
TEST=Build for reef
Change-Id: I31f854adf3269ba6f77c4044fb3748bb1957841c
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/18725
Tested-by: build bot (Jenkins)
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Fix the following warning detected by checkpatch.pl:
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
TEST=Build for reef
Change-Id: Ifc45ce90d466d087cd20af72ddfc8486d2f1492c
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/18724
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Fix the following warnings detected by checkpatch.pl:
WARNING: braces {} are not necessary for any arm of this statement
WARNING: braces {} are not necessary for single statement blocks
TEST=Build for reef
Change-Id: Ifab09c023faa7da215945f1aedd391f4b2a1a04c
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/18723
Tested-by: build bot (Jenkins)
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Fix the following error and warnings detected by checkpatch.pl:
ERROR: code indent should use tabs where possible
WARNING: please, no spaces at the start of a line
WARNING: please, no space before tabs
TEST=Build for reef
Change-Id: Id7a758463b95274c5e8bbdd67da0955f1ae78aac
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/18721
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Fix the following errors detected by checkpatch.pl:
ERROR: spaces required around that '==' (ctx:VxO)
ERROR: space required before that '-' (ctx:OxV)
ERROR: spaces required around that '=' (ctx:VxW)
ERROR: spaces required around that '=' (ctx:WxV)
ERROR: spaces required around that '=' (ctx:VxV)
ERROR: need consistent spacing around '+' (ctx:VxW)
ERROR: space prohibited before that '++' (ctx:WxB)
ERROR: space prohibited before that ',' (ctx:WxW)
ERROR: space required after that ',' (ctx:VxV)
TEST=Build for reef
Change-Id: I37265a69fcb14fbf7c182ef29d823f70a5748ad8
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/18720
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Fix the following errors detected by checkpatch.pl:
ERROR: "foo * bar" should be "foo *bar"
ERROR: "(foo*)" should be "(foo *)"
TEST=Build for reef
Change-Id: I4a762d8fa762057a06e601dfed10538adc5d8bc8
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/18719
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Fix the following error detected by checkpatch.pl:
ERROR: open brace '{' following function declarations go on the next line
TEST=Build for reef
Change-Id: Icb92dc49c6e7b8dfea60bc0395f3db7316c4e34c
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/18722
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Fix the following error detected by checkpatch.pl:
ERROR: return is not a function, parentheses are not required
TEST=Build and run on Galileo Gen2
Change-Id: Idf7723d4fd48124a26bbb626afc310820f859f66
Signed-off-by: Lee Leahy <Leroy.P.Leahy@intel.com>
Reviewed-on: https://review.coreboot.org/18757
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Fix the following warning detected by checkpatach.pl:
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
TEST=Build and run on Galileo Gen2
Change-Id: Ic266c077eb115e0c7d934c15bcc4cc9b9e530a39
Signed-off-by: Lee Leahy <Leroy.P.Leahy@intel.com>
Reviewed-on: https://review.coreboot.org/18756
Tested-by: build bot (Jenkins)
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Fix the following errors detected by checkpatch.pl:
ERROR: spaces required around that '=' (ctx:VxV)
ERROR: spaces required around that ':' (ctx:VxW)
ERROR: space required after that ',' (ctx:VxV)
ERROR: space required before the open parenthesis '('
ERROR: switch and case should be at the same indent
ERROR: "foo ** bar" should be "foo **bar"
TEST=Build and run on Galileo Gen2
Change-Id: I52ba2a3c1e0fffad7145eecd878aba8dc450ac0b
Signed-off-by: Lee Leahy <Leroy.P.Leahy@intel.com>
Reviewed-on: https://review.coreboot.org/18755
Tested-by: build bot (Jenkins)
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Fix the following error detected by checkpatch.pl:
ERROR: code indent should use tabs where possible
TEST=Build and run on Galileo Gen2
Change-Id: I61c4f01216cb6c788cf6da988c414bbb9648d502
Signed-off-by: Lee Leahy <Leroy.P.Leahy@intel.com>
Reviewed-on: https://review.coreboot.org/18754
Tested-by: build bot (Jenkins)
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
In strncpy() function of dimm_info_fill(), the minimum possible size
of Module Part Number of DIMM is passed as argument.
BUG=chrome-os-partner:61729
BRANCH=none
TEST=Build and boot KBLRVP to verify the type 17 DIMM info coming in
SMBIOS Table from Kernel command "dmidecode".
Change-Id: Icc7667149eae9705b91e271628af1b443eb8556e
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/18617
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
CDClk selection was wrong in some corner cases (e.g. ULX SKUs) and,
for Broadwell, never took the devicetree config into account.
Rewrite the selection with the following in mind:
o cpu_is_ult() might return `true` for ULX SKUs, too,
o ULX and Broadwell-ULT SKUs can be `overclocked` with additional
cooling, so leave that as devicetree option.
For Haswell, the following frequency selections are valid:
o ULX: 337.5MHz by default, 450MHz optional
o ULT: 450MHz only (maybe 337.5MHz too, documentation varies,
it wasn't selectable before either)
o others: 540MHz by default, 450MHz optional
For Broadwell:
o ULX: 450MHz by default, 337.5MHz / 540MHz optional
o ULT: 540MHz by default, 337.5MHz / 450MHz / 675MHz optional
o others: 667MHz by default, 337.5MHz / 450MHz / 540MHz optional
Side effects: A too high setting in the devicetree results in the
highest possible frequency now, Haswell non-ULT/ULX defaults to 540MHz
instead of 450MHz.
Change-Id: Iec12752f2a47bf4a5ae6077c75790eae9378c1b2
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/17768
Tested-by: build bot (Jenkins)
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
eMMC Controller is taking over 100ms to resume during runtime which
results in I/O latency issues on the Skylake systems like Cave and Caroline.
This patch adds _DSM method for eMMC comtroller for specifying the
device readiness durations. Function index 9 returns package of five
integers to set D3 cold delay to zero and ACPI constant Ones for the
elements where overriding the default values is not desired.
BUG=b:35774937
BRANCH=none
TEST=update caroline coreboot and test i/o latency is under 100ms
Change-Id: Iacc8aa8560897da8770fe559ca8cd17aaf6ebeba
Signed-off-by: Sowmya V <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/18532
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
This implements dynamic generation of sdcard GpioInt in SSDT.
GpioInt in SSDT generation is based on the card detect GPIO if
it is provided by the mainboard in devicetree.
This implements GNVS variable to store the address of sdcard cd pin.
GNVS used to store rxstate of the sdcard cd pin to get card presence.
Add _PS0/_PS3 methods to power gate the sd card controller in
S0ix and runtime PM.
CQ-DEPEND=448173
BUG=chrome-os-partner:63070
TEST=Suspend and resume using 'echo freeze > /sys/power/state'.
System should enter S0ix and resume with no issue.
Change-Id: Id2c42fc66062f0431385607cff1a83563eaeef87
Signed-off-by: Venkateswarlu Vinjamuri <venkateswarlu.v.vinjamuri@intel.com>
Reviewed-on: https://review.coreboot.org/18496
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Vaibhav Shankar <vaibhav.shankar@intel.com>
Add two GPIO macros:
1. PAD_CFG_GPI_APIC_EDGE allows a pin to be route to the
APIC with input assuming the events are edge triggered.
2. PAD_CFG_GPI_ACPI_SCI_LEVEL to route the general purpose
input to SCI assuming the events are level triggered.
Change-Id: I944a9abac66b7780b2336148ae8c7fa3a8410f3f
Signed-off-by: Rahul Kumar Gupta <rahul.kumarxx.gupta@intel.com>
Reviewed-on: https://review.coreboot.org/18533
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Add SKL/KBL PCH-H GPIO settings referring from SKL PCH-H
specifications to support sklrvp11.
Split the gpio_defs.h into headers gpio_pch_h_defs.h and
gpio_soc_defs.h for PCH-H specific and SOC specific GPIO
defs respectively.
Change-Id: I5eaf8d809a1244a56038cbfc29502910eb90f9f2
Signed-off-by: Li Cheng Sooi <li.cheng.sooi@intel.com>
Signed-off-by: Rahul Kumar Gupta <rahul.kumarxx.gupta@intel.com>
Reviewed-on: https://review.coreboot.org/18027
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Apollolake platform comes with FPF (field-programmable-fuses). FPF can
be blown only once, typically at the end of the manufacturing process.
This patch adds code that sends a request to CSE to figure out if FPFs
have already been blown.
Change-Id: I9e768a8b95a3cb48adf66e1f17803c720908802d
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/18604
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Add common driver that can send/receive HECI messages. This driver is
inspired by Linux kernel mei driver and somewhat based on Skylake's.
Currently it has been only tested on Apollolake.
BUG=b:35586975
BRANCH=reef
TEST=tested on Apollolake to send single messages and receive both
fragmented and non-fragmented versions.
Change-Id: Ie3772700270f4f333292b80d59f79555851780f7
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/18547
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
If Deep Sx is enabled the event log will get entries added on every
power sequence transition indicating that the suspend well has failed.
When a board is using Deep Sx by design this is intended behavior and
just fills the logs with extraneous events.
To make this work the device init state has to be executed first so it
actually enables the Deep Sx policies in the SOC since this code does
not have any hooks back into the devicetree to read the intended setting
from there.
BUG=b:36042662
BRANCH=none
TEST=Perform suspend/resume on Eve device with Deep S3 enabled, and
then check the event log to be sure that it does not contain the
"SUS Power Fail" event.
Change-Id: I3c8242baa63685232025e1dfef5595ec0ec6d14a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18664
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Add a function to read the current state of Deep S5 configuration
and indicate if it is enabled (for AC and/or DC) or disabled.
This is similar to the existing function that checks Deep S3
enable state.
BUG=b:36042662
BRANCH=none
TEST=tested with subsequent commits to check Deep S5 state at boot
and filter event log messages if it is enabled.
Change-Id: I4b60fb99a99952cb3ca6be29f257bb5894ff5a52
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18663
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Add options to the skylake chip config that will allow tuning the
various settings that can affect acoustics with the CPU and its VRs.
These settings are applied inside FSP, and they can adjust the slew
slew rate when changing voltages or disable fast C-state ramping on
the various CPU VR rails.
BUG=b:35581264
BRANCH=none
TEST=these are currently unused, but I verified that enabling the
options can affect the acoustics of a system at runtime.
Change-Id: I6a8ec0b8d3bd38b330cb4836bfa5bbbfc87dc3fb
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18662
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Fix the errors detected by checkpatch and update the copyright dates.
TEST=Build and run on Galileo Gen2
Change-Id: Idad062eaeca20519394c2cd24d803c546d8e0ae0
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/18591
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Fix the following issues:
* A raw read is described by a single read segment, don't assert.
* Support reads longer than the FIFO size.
* Support writes longer than the FIFO size.
* Use the 400 KHz clock by default.
* Remove the error displays since vboot device polling generates
errors.
TEST=Build and run on Galileo Gen2
Change-Id: I421ebb23989aa283b5182dcae4f8099c9ec16eee
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/18029
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Move all common MSRs as per IA SDM into a common location
to avoid duplication.
Change-Id: I06d609e722f4285c39ae4fd4ca6e1c562dd6f901
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/18509
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Select all Kconfig belongs into Intel SoC Family block/ips common
code model and include required header.h file.
Change-Id: Idbce59a57533dbeb9ccfadca966c3d7560537fa0
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/18377
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Support for voltage margining is dependent on the platform.
Enabling voltage margining puts additional constraints for
the SLP_S0# to be asserted and hence moving to S0ix state.
If the platform PMIC/VR supports PCH voltage reduction,
voltage marigining can be enabled.
Use the UPD provided by FSP to enable/disable voltage margining.
Change-Id: Iea214e9d7d6126e8367426485c6446ced63caa66
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/18469
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Fix a typo that was introduce in commit 696ebc2d (Broadwell/Sata:
Add support for setting IOBP registers for Ports 2 and 3.) [1].
Setting one of the SATA port 3 IOBP setting was using the value from
the port 2 register.
On the purism/librem13 (on which SATA port 3 is tested), this change
doesn't seem to affect anything, as that typo wasn't exhibiting any
visible problems anyways.
[1] https://review.coreboot.org/18408
Change-Id: I3948def5c0588791009c4b24cbc061552d9d1d48
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/18514
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Philippe Mathieu-Daudé <philippe.mathieu.daude@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Save SMBIOS memory information from FSP MEM_INFO_DATA_HOB in CBMEM.
Add function dimm_info_fill() which populates SMBIOS memory
information from FSP MEM_INFO_DATA_HOB data.
BUG=chrome-os-partner:61729
BRANCH=none
TEST=Build and boot KBLRVP to verify the type 17 DIMM info coming in
SMBIOS table from Kernel command "dmidecode".
Change-Id: I0fd7c9887076d3fdd320fcbdcc873cb1965b950c
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/18418
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Camera and Imaging device should be enabled for camera usecase,
FSP provides a UPD to enable/disable the SA IMGU (Imaging Unit)
expose the same as a config option in devicetree.cb
Also remove a redundant assignment for PchCio2Enable.
BUG=None
BRANCH=None
TEST=lspci should list 00:05:00
Change-Id: I4cf7daf41bfaf4dcba414921cac2e7e12bf89f37
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/18365
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
This enables some required Kconfig options when CONFIG_CHROMEOS is set.
Change-Id: I290902746c1ea19c8bcb69540e34fde09abb9adf
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-on: https://review.coreboot.org/18448
Tested-by: build bot (Jenkins)
Reviewed-by: Julius Werner <jwerner@chromium.org>
The Broadwell SATA controller supports IOBP registers on ports 0 and 1 but
Browell supports up to 4 ports, so we need to support setting IOBP for
ports 2 and 3 as well.
The magic numbers (IOBP SECRT88 and DTLE) for ports 2 and 3 were only
guessed by looking at ports 0 and 1 and extrapolating from there.
Port 3 has been tested (DTLE setting on Librem 13) and confirmed to work
so we can assume that port 2 and 3 magic numbers are valid, but having
someone confirm them (through non-public documents?) would be great.
Change-Id: I59911cfa677749ceea9a544a99b444722392e72d
Signed-off-by: Youness Alaoui <youness.alaoui@puri.sm>
Reviewed-on: https://review.coreboot.org/18408
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
This is done to avoid any conflicts with same IRQ enums defined by other
drivers.
BUG=None
BRANCH=None
TEST=Compiles successfully
Change-Id: I539831d853286ca45f6c36c3812a6fa9602df24c
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18444
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Adding spi_xfer_two_vectors as .xfer_vector for ipq40xx spi_ctrlr.
Commit c2973d196d ("UPSTREAM: spi: Get rid of SPI_ATOMIC_SEQUENCING")
has added a new driver method xfer_vector to support combined write-read
operation within a single CS cycle. The method is wrapped in the
spi_xfer_vector() API. When spi_ctrlr structure does not have
xfer_vector method, API calls write and read operations sequentially.
However the QCA40xx SPI driver has "forced" CS activation-inactivation
in xfer method, so individual operation will break CS after write
operation, making combined write-read cycle broken.
Adding xfer_vector method to spi_ctrlr is a simple fix to prevent this.
BUG=None
BRANCH=none
TEST=built and run on Gale
Change-Id: I2258e563d0793bcacd626f78b8e96b3649a8e4a4
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 88a8824951cef4fe293dfa6e3a1a837ae07b6156
Original-Change-Id: I031e85ce5b847353cb1084f6f68b2af8c6f702e1
Original-Signed-off-by: Yuji Sasaki <sasakiy@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/433439
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-by: Kan Yan <kyan@google.com>
Reviewed-on: https://review.coreboot.org/18297
Tested-by: build bot (Jenkins)
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Martin Roth <martinroth@google.com>
With recent change (a4b11e5c90: soc/intel/skylake: Perform CPU MP Init
before FSP-S Init) to perform CPU MP init before FSP-S init, suspend
resume is currently broken for all skylake/kabylake boards. All the
skylake/kabylake boards store external stage cache in TSEG, which is
relocated post MP-init. Thus, if FSP loading and initialization is
done after MP-init, then ramstage is not able to:
1. Save FSP component in external stage cache during normal boot, and
2. Load FSP component from external stage cache during resume
In order to fix this, ensure that FSP loading happens separately from
FSP initialization. Add fsp_load callback for pre_mp_init which ensures
that the required FSP component is loaded/saved from/to external stage
cache.
BUG=chrome-os-partner:63114
BRANCH=None
TEST=Verified that 100 cycles of suspend/resume worked fine on poppy.
Change-Id: I5b4deaf936a05b9bccf2f30b949674e2ba993488
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/18414
Tested-by: build bot (Jenkins)
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Currently the USB OC pins definition only being defined up to OC3.
For PCH-H, OC4 and OC5 are needed, so add both into OC pin enum.
Changes is being verified and booted to Yocto with Saddle Brook.
Change-Id: Idaed6fa7dcddb9c688966e8bc59f656aec2b26eb
Signed-off-by: Teo Boon Tiong <boon.tiong.teo@intel.com>
Reviewed-on: https://review.coreboot.org/18364
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Setting both bits 27 and 7 of PCH register PMSYNC_CFG (PMSYNC
Configuration; offset 0x33c8) causes pre-OS display init to fail
on HSW-U/Lynxpoint and BDW-U ChromeOS devices when the VBIOS/GOP
driver is run after the register is set. A re-examination of
Intel's reference code reveals that bit 7 should be set for the
LP PCH, and bit 27 for non-LP, but not both simultaneously.
The previous workaround was to disable the entire power optimizer
section via a Kconfig option, which isn't ideal.
Test: unset bit 27 of PMSYNC_CFG and boot google/lulu,
observe functional pre-OS video output
Change-Id: I446e169d23dd446710a1648f0a9b9599568b80aa
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/18385
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
We've been able to narrow down the problem to a single register/
single bit, so revert this commit and address the problem in a
follow-on commit.
This reverts commit 0f2025da0f.
Change-Id: I780f9ea2976dd223aaa3e060aef6e1af8012c346
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/18384
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
There is an enable_s0ix config option in the devicetree that should
be used to disable it when not set:
- do not export C8/C9/C10 C-states in _CST
- do not enable SLP_S0 in FSP
BUG=chrome-os-partner:58666
TEST=test on eve board to ensure that OS only sees 3 ACPI C-states
instead of 6 and that it no longer attempts to enter C10
Change-Id: I90e4dc776d1d17d0b700cda63c8476786cd2e4ff
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18394
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Prmrr configuration is supported by Kabylake FSP-M with UPD provided.
It is required as one of the SGX initialization steps in BIOS.
BUG=chrome-os-partner:62438
BRANCH=NONE
TEST=Tested on Eve, verified uncore PRMRR MSRs get programmed to set
size and boot.
Change-Id: I2b3dc7c92487505165ee429bd1a37bd60ceac8f3
Signed-off-by: Robbie Zhang <robbie.zhang@intel.com>
Reviewed-on: https://review.coreboot.org/18361
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Currently there is no distinction between mainboards using
Skylake or Kabylake SoC, Add a config option for Kabylake
SoC to allow mainboards to explicitly select if they are
using it.
Change-Id: Ie7960bd81f88a223894afe3115ddc0bc637e4be4
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/18312
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
There are MSRs that are programmable per-core not per-thread, so add
a function to check whether current executing CPU is a primary core
or a "hyperthreaded"/secondary core. For instance when trying to
program Core PRMRR MSRs(per-core) with mp_init, cpu exception is thrown
from the secondary thread. This function was used to avoid that.
Potentially this function can be put to common code or arch/x86 or cpu/x86.
BUG=chrome-os-partner:62438
BRANCH=NONE
TEST=Tested on Eve, verified core PRMRR MSRs get programmed only on primary
thread avoiding exeception.
Change-Id: Ic9648351fadf912164a39206788859baf3e5c173
Signed-off-by: Robbie Zhang <robbie.zhang@intel.com>
Reviewed-on: https://review.coreboot.org/18366
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
As per BWG, CPU MP Init (loading ucode) should be done prior
to BIOS_RESET_CPL. Hence, pull MP Init to BS_DEV_INIT_CHIPS Entry
(before FSP-S call).
BUG=chrome-os-partner:62438
BRANCH=NONE
TEST=Boot to OS with all threads enabled.
Change-Id: Ia6f83d466fb27e1290da84abe7832dc814b5273a
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/18287
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This reverts commit 32997fb0bc.
This change is breaking I2S audio on Kabylake platforms so
revert the change to fix audio.
BUG=chrome-os-partner:61548,chrome-os-partner:61009
TEST=manual testing on Eve P1 system
Change-Id: I3212c8be83078ed57e38501386605e67b87d5bd0
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18360
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Some variants need the internal pull resistor on GPIO_SSUS_40
set explicitly to pull down rather than disabling the pull,
in order for the ram-id to be read correctly via GPIO.
Correct this by adding a function to enable and set the internal pull
and define its use as needed in the board's variant.h.
Chromium source:
branch: firmware-gnawty-5216.239.B
/src/soc/intel/baytrail/baytrail/gpio.h#418
/src/mainboard/google/gnawty/romstage.c#60
Test: boot 4GB Candy board and observe correct RAM id, amount detected
Change-Id: I8823c27385f4422184b5afa57f6048f7ff2a25ab
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/18309
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Kernel relies on FADT 8042 flag to enable/disable
8042 interface. If FADT reports 8042 capability and
8042 (/PS2) capability is actually disabled by coreboot,
kernel would assume the presence of 8042 based on the
FADT flag. This results in undesired system power off when
kernel tries to access the 8042 memory region. To address
this, CONFIG_NO_FADT_8042 was added to selectively
disable 8042 on FADT.
BUG=chrome-os-partner:61858
TEST=Boot OS and verify FADT 8042 flag
Change-Id: Ic80b3835cb5cccdde1203e24a58e28746b0196fc
Signed-off-by: Jenny TC <jenny.tc@intel.com>
Reviewed-on: https://review.coreboot.org/18307
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Dump the CSE status registers for potential debugging purposes.
Explicitly call out manufacturing mode of the part since it's
important shipping devices ensure manufacturing mode is locked
down. Intel is planning on writing a common driver so a complete
status -> string dumps was not done because (surprise surprise)
not all the fields are equal with previous implementations.
BUG=chrome-os-partner:62177
BRANCH=reef
TEST=Booted and noted dump of CSE status registers.
Change-Id: I71d15722bb193877f1569c1d3e7f441302f5bd14
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/18303
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
It may cause an edp aux transfer error if the edp pclk is
set too high, so reduce it to 25MHz.
BUG=chrome-os-partner:60130
BRANCH=None
TEST=Build and Boot
Change-Id: Id1063baa5a82637b03c0f1f754181df074ab17cc
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 8f7ce31a7483e765ae0c86f8e62ef51413ee1596
Original-Change-Id: Ibb86c12c1d7c00dc3b4cc7a6bdf3bd6e895cd9f3
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/429410
Original-Commit-Ready: Julius Werner <jwerner@chromium.org>
Original-Tested-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/18178
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
The lpss_i2c driver is enabled in romstage, so the SOC needs to
export the pre-ram compatible I2C controller info, which for
skylake is in the bootblock/i2c.c file.
This was not causing a compiler error in normal use, but when
adding I2C debug code in romstage it failed to compile.
With this added, I can now do I2C transactions in romstage.
Change-Id: I0778b0497d0b6936df47c29b2ce942c8d90cf39b
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18198
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The define for GPIO_13_IRQ had the wrong IRQ number. It should
be 0x70 instead of 0x6f.
BUG=chrome-os-partner:62085
BRANCH=reef
TEST=touch controller doesn't indicate continuous interrupts
Change-Id: I3a0726db59fc1eb7736d348aecbf1082719f15b2
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/18190
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
As per Audio PCH team recommendation the iDisplay Audio/SDIN2
should be disabled to bypass InitializeDisplayAudio() function
call. Display Audio Codec is HDA-Link Codec, which is not
supported in I2S mode
BUG=chrome-os-partner:61548
BRANCH=none
TEST=Tested to verify that InitializeDisplayAudio() does not
get called.
Change-Id: Ie0771a8653821e737d10e876313917b4b7c64499
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/18091
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Currently car_stage_entry is defined only in romstage_after_verstage and
as a result when SEPARATE_VERSTAGE is not selected, there is no
entry point into romstage and romstage will not be started at all.
The solution is move out romstage_after_verstage.S from fsp1.1 driver
to skylake/romstage. And add CONFIG_PLATFORM_USES_FSP1_1 to fix the
build and boot issue with this change.
Besides that, rename the romstage_after_verstage to romstage_c_entry
in more appropriate naming convention after this fix.
Tested on SkyLake Saddle Brook (FSP 1.1) and KabyLake Rvp11 (FSP 2.0),
romstage can be started successfully.
Change-Id: I1cd2cf5655fdff6e23b7b76c3974e7dfd3835efd
Signed-off-by: Teo Boon Tiong <boon.tiong.teo@intel.com>
Reviewed-on: https://review.coreboot.org/17976
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
This code allows people to override the usb2 eye pattern
UPD settings for boards.
BUG=chrome-os-partner:61031
BRANCH=None
TEST=Usb2 function ok and make sure fsp upd is overridden
Change-Id: I5fab620a29aba196edf1f24ffe6a1695de1e523e
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/18060
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Baytrail SoC has a bug where in some cases the DisplayPort can hang
leading to a non-working display (it just stays black). To avoid this
hang, a patch was introduced in 02/2016
(1c3b1112fa - fsp_baytrail: Fix a possible hanging DisplayPort)
but per default not switched on so that each
mainboard can decide if it wants to use this patch or not.
Recently a new case of this bug was reported by Benoit Sansoni
(benoit.sansoni@kontron.com) and he requested to enable this fix per
default as it costs him a lot of time to find the cause and even the
already available fix in coreboot. To avoid this effort for someone
else in the future we can enable this fix per default as no negative
side effects are known and it is now tested at Siemens and at
Kontron on different mainboards with success.
As the goal is to enable this code permanently the config switch is not
longer needed and is removed.
Change-Id: I15bd682218d0dc887945cc91ee3e5488945a6355
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/18109
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
After we set the GET_TIME bit, the rtc time can't be read immediately. We
should wait up to 31.25 us, about one cycle of 32khz. Otherwise reading
RTC time will return a old time.
BUG=chrome-os-partner:61078
BRANCH=veyron
TEST=Build and Boot
Original-Change-Id: I6ec07fc6c4d6d8b27b12031423b86b8ab15da6f6
Original-Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/423272
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Change-Id: I9806b624d6e968e51d52aab8c052ae3fa77f247d
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: b4b708e29fbae0d8f5a2cece79711aa6b1887727
Original-Change-Id: I8c168c14437bb932a59ac0e91a01062df0cf11dc
Original-Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/427522
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/18127
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Cosmetic changes to rename car_stage.S to car_stage_fsp20.S,
so that it is associated with FSP driver version that is being used.
Tested on Kabylake Rvp11.
Change-Id: I869df6eb746e3982e5912c272255eab6cb008838
Signed-off-by: Teo Boon Tiong <boon.tiong.teo@intel.com>
Reviewed-on: https://review.coreboot.org/18083
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
mvmap2315_reset() is called from locations where we're checking for NULL
pointers. Because coverity can't tell from the code that the functions
are not returning, it's showing errors of accessing pointers after
we've determined that they're invalid.
Mark it as noreturn, and add a loop in case the reset isn't on the
next instruction. This probably isn't needed, but shouldn't hurt.
Found-by: Coverity Scan #1362809
Change-Id: If93084629d5c2c8dc232558f2559b78b1ca5de7c
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/18103
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Updated to arm-trusted-firmware TOT:
236c27d2 (Merge pull request #805 from Xilinx/zynqmp/addr_space_size)
183 commits between Sep 20, 2016 and January 10, 2017
- Also add associated change to src/soc/rockship/rk3399 Makefile.inc
that is required to build the M0 Firmware.
Change-Id: I49695f3287a742cd1fb603b890d124f60788f88f
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/18024
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Die if cbmem_add can't allocate memory for the hob pointer. This
shouldn't ever happen, but it's a reasonable check.
- fsp_broadwell_de already had a check, but it returned to someplace
inside the FSP. Just die instead.
Change-Id: Ieef8d6ab81aab0ec3d52b729e34566bb34ee0623
Found-by: Coverity Scan #1291162
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/18092
Tested-by: build bot (Jenkins)
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
The FSP 2.0 change broke the logic for determining whether or not
to execute the GOP binary. Modify the FSP 2.0 code to do the right
thing and check for display_init_required() before passing VBT into
FSP and the GOP binary.
BUG=chrome-os-partner:61726
TEST=disable developer mode and ensure FSP does not run GOP
Change-Id: I7fc8055b6664e0cf231a8de34367406eb049dfe1
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/18084
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Nothing from that header is used or even declared since
CONFIG_HYPERTRANSPORT_PLUGIN_SUPPORT is not selected on Intel
hardware.
Change-Id: I9101eb6ffa6664a2ab45bc0b247279c916266537
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18044
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Idwer Vollering <vidwer@gmail.com>
Add the Kconfig value HAVE_MONOTONIC_TIMER and the routine to read the
TSC for the monotonic timer. Simplify the routine to get the TSC
frequency.
TEST=Build and run on Galileo Gen2
Change-Id: I806fb864b01e39277bf2d6276254b0543930c2f6
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/18002
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
I've recently added an assertion to ensure that the effective I2C
frequency on Rockchip SoCs is not too far off the 400KHz target due to
divisor rounding errors. A 10KHz margin worked fine for RK3399, but it
turns out that RK3288 actually only ever hit 387KHz since its I2C clocks
are based off the already pretty low 75MHz PCLKs. While we could
probably change the PCLKs to make this closer, that seems like a too
intrusive change for something that has already worked just fine for
years, so just loosen the restriction a little more instead.
BRANCH=None
BUG=chromium:675043
TEST=None
Change-Id: I7e96a1a75b38f8ad3971dd33046699cceb17b80d
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://chromium-review.googlesource.com/421095
Reviewed-by: Randall Spangler <rspangler@chromium.org>
Reviewed-on: https://review.coreboot.org/18007
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Add Kconfig values and early debugging code to better segment and debug
the early code in bootblock by using the SD LED as an indicator. Update
the help text for the debug Kconfig values to point to the various
failure locations.
TEST=Build and run on Galileo Gen2
Change-Id: I1cd62eba3e9547cb1dd7f547aaec5d4827e14633
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/17985
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Fix serial port configuration broken by how PCI configuration space was
referenced introduced by change 3d15e10a (MMCONF_SUPPORT: Flip default
to enabled).
TEST=Build and run on Galileo Gen2
Change-Id: I2ab52cf598795e94f1f16977f8d12b7fdd95e146
Signed-off-by: Lee Leahy <leroy.p.leahy@intel.com>
Reviewed-on: https://review.coreboot.org/17984
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Migrate duplicated enable_vmx() method from multiple CPUs to common
folder. Add common virtualization option for CPUs which support it.
Note that this changes the default to enable virtualization on CPUs
that support it.
Change-Id: Ib110bed6c9f5508e3f867dcdc6f341fc50e501d1
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/17874
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins)
TCC activation functionality has package scope. It was set
for all CPU in the system which is unnecessary.
In this patch TCC activation is being set by the BSP only.
BUG=chrome-os-partner:59397
BRANCH=None.
TEST=Built for skylake platform and verified the TCC activation
value before and after S3.
Change-Id: Iacf64cbc40871bbec3bede65f196bf292e0149a6
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/17889
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
SPI_ATOMIC_SEQUENCING was added to accomodate spi flash controllers with
the ability to perform tx and rx of flash command and response at the
same time. Instead of introducing this notion at SPI flash driver layer,
clean up the interface to SPI used by flash.
Flash uses a command-response kind of communication. Thus, even though
SPI is duplex, flash command needs to be sent out on SPI bus and then
flash response should be received on the bus. Some specialized x86
flash controllers are capable of handling command and response in a
single transaction.
In order to support all the varied cases:
1. Add spi_xfer_vector that takes as input a vector of SPI operations
and calls back into SPI controller driver to process these operations.
2. In order to accomodate flash command-response model, use two vectors
while calling into spi_xfer_vector -- one with dout set to
non-NULL(command) and other with din set to non-NULL(response).
3. For specialized SPI flash controllers combine two successive vectors
if the transactions look like a command-response pair.
4. Provide helper functions for common cases like supporting only 2
vectors at a time, supporting n vectors at a time, default vector
operation to cycle through all SPI op vectors one by one.
BUG=chrome-os-partner:59832
BRANCH=None
TEST=Compiles successfully
Change-Id: I4c9e78c585ad95c40c0d5af078ff8251da286236
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17681
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
1. Define controller for fast SPI.
2. Separate out functions that are specific to SPI and flash
controller in different files.
BUG=chrome-os-partner:59832
BRANCh=None
TEST=Compiles successfully for chell and eve.
Change-Id: I2fe0ef937297297339d4ea19dc37d3061caaa80c
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17933
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
FSP v2.0 Driver supports TempRamInit & TempRamExit APIs to initialize
& tear down Cache-As-Ram. Add TempRamInit & TempRamExit usage to
ApolloLake SoC when CONFIG_FSP_CAR is enabled.
Verified on Intel Leaf Hill CRB and confirmed that Cache-As-Ram
is correctly set up and torn down using the FSP v2.0 APIs
without coreboot implementation of CAR init/teardown.
Change-Id: Ifd6fe8398ea147a5fb8c60076b93205bb94b1f25
Signed-off-by: Brenton Dong <brenton.m.dong@intel.com>
Reviewed-on: https://review.coreboot.org/17063
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
There was an assumption that all SPI controllers could
consume a full page of data to write. However, that
assumption doesn't hold when spi_crop_chunk() indicates
sizes smaller than page size. If the requested offset isn't
page aligned from the start then writes will fail corrupting
data since a page boundary isn't honored.
The spansion driver needed quite a bit more work to honor
the spi_crop_chunk() result. It now mimics the other
driver's code. Also, needed to add spi_crop_chunk() to
marvell/bg4cd SoC to make google/cosmos build. SPI obviously
doesn't work on that platform, but it fixes the build error.
Change-Id: I93e24a5a717adcee45a017c164bd960f4592ad50
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/17910
Tested-by: build bot (Jenkins)
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
It was unsigned, not a good place to be for testing < 0.
Change-Id: I126fe86422900bbae2c3ca16052be27985cfed53
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Found-by: Coverity Scan #1241911
Reviewed-on: https://review.coreboot.org/17888
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins)
Change-Id: Ic1d1b85a1d7e85b555a93b3a0b55fe310b26e34a
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Found-by: Coverity Scan #1353362
Reviewed-on: https://review.coreboot.org/17875
Tested-by: build bot (Jenkins)
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Allow a board/platform to invalidate the normal MRC cache when
hardware retraining is requested in recovery mode. A small 4 byte
payload is used to update the latest data written. It will of course
fail on MRC cache retreival on next usage.
BUG=chrome-os-partner:60592
BRANCH=reef
Change-Id: Ic88cd66802664813562d003f50d54e4a4ea375ef
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/17870
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Rely on boot_device_spi_flash() to provide the spi_flash
object. There's no need to duplicate the probing logic.
BUG=chrome-os-partner:56151
BRANCH=reef
Change-Id: I91900a3dfad7ba92cbd3b0ace77b08db04cff0b6
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/17867
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Update the mrc cache implementation to use region_file. Instead
of relying on memory-mapped access and pointer arithmetic
use the region_devices and region_file to obtain the latest
data associated with the region. This removes the need for the
nvm wrapper as the region_devices can be used directly. Thus,
the library is more generic and can be extended to work on
different boot mediums.
BUG=chrome-os-partner:56151
Change-Id: Ic14e2d2f7339e50256b4a3a297fc33991861ca44
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/17717
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
The gnvs table only needs to be zeroized after init;
zeroizing an existing/populated table renders all I2C devices
completely non-functional.
TEST: boot Linux and observe all I2C devices functional
Change-Id: Id149ad645dfe5ed999a65d10e786e17585abc477
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/17828
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Set aclk_emmc and clk_emmc to 148.5MHz under hs400es mode, which could
improve stability like kernel.
CQ-DEPEND=CL:386527
BUG=chrome-os-partner:54377
BRANCH=none
TEST=build and boot on kevin
Change-Id: Iaa76d3ec1ab999eb317a9ab6c7e3525594b15b57
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: e6eb1f56371aea51f2584a97bf817189d61090b2
Original-Change-Id: If4754d22e83a0f9a029fedca12f26ff5ae8d44e1
Original-Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/386865
Original-Commit-Ready: Julius Werner <jwerner@chromium.org>
Original-Tested-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/17790
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
- Separate mma code for fsp1.1 and fsp2.0
and restructuring the code
- common code is placed in mma.c and mma.h
- mma_fsp<ver>.h and fsp<ver>/mma_core.c contains
fsp version specific code.
- whole MMA feature is guarded by CONFIG_MMA flag.
Change-Id: I12c9a1122ea7a52f050b852738fb95d03ce44800
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/17496
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The value for _size was not evaluated correctly if ramstage
is relocated, make the calculation runtime.
While touching it, move symbol declarations to header file.
Change-Id: I4402315945771acf1c86a81cac6d43f1fe99a2a2
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17784
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Previously privilege drop was happening "too early" and that caused some
PMC IPC programming (performed in FSP) to fail because sideband was
already locked out. This change set moves privilege drop to later stage,
after last FSP notify call.
BRANCH=reef
BUG=chrome-os-partner:60657
TEST=iotools rdmsr X 0x121, make sure they can't be read.
Also dmesg|grep -i IPC to make sure there are no errors related
Change-Id: Ia3a774aee5fbf92805a5c69093bfbd3d7682c3a7
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/17769
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The EM4/EM5 registers in the mini-HD audio device must be set based
on the GPU cdclk value in order for HDMI audio to function properly.
Add variables to save the correct values when initializing the GPU,
and accessor functions to retrieve them in order to set the registers
when initializing the mini-HD audio device.
Change-Id: Icce7d5981f0b2ccb09d3861b28b843a260c8aeba
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/17718
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
1. Define controller for fast SPI.
2. Separate out functions that are specific to SPI and flash controller
in different files.
BUG=chrome-os-partner:59832
BRANCH=None
TEST=Compiles successfully for reef.
Change-Id: If07db9d27bbf4f4eb6024175cb7753c6cf4fb793
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17562
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Skylake uses a special SPI Flash controller and does not require
spi_claim_bus and spi_release_bus functionality. This was a leftover
call from earlier cleanup, so remove it.
Change-Id: Iea260813cf72b94b7e7c661dbe494a74351dc357
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17729
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Resource is actually stored even before read_resources, but
that's where we currently log this resource.
For Intel, use PCI config register offset as the resource
index, while AMD side uses MSR address.
Change-Id: I6eeef1883c5d1ee5bbcebd1731c0e356af3fd781
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17696
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Doing PCI config operations via MMIO window by default is a
requirement, if supported by the platform. This means chipset
or CPU code must enable MMCONF operations early in bootblock
already, or before platform-specific romstage entry.
Platforms are allowed to have NO_MMCONF_SUPPORT only in the
case it is actually not implemented in the silicon.
Change-Id: Id4d9029dec2fe195f09373320de800fcdf88c15d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17693
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
We may support different sdram sizes on one board in future, so
we need to calculate sdram sizes from sdram drvier.
BRANCH=None
BUG=None
TEST=boot kevin
Change-Id: I43e8f164ecdb768c051464b4dbc7d890df8055d0
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 3c4d8b3cb647b2f9cebc416c298817c16d49330e
Original-Change-Id: I95d5ef34de9d79ebca3600dc7a4b9e14449606ff
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/411600
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/17629
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Resource allocator and 64-bit PCI BARs will need it and
PCI use is not really restricted to x86.
Change-Id: Ie97f0f73380118f43ec6271aed5617d62a4f5532
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17733
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
MMCONF was explicitly used here to avoid races of 0xcf8/0xcfc access
being non-atomic and/or need to access 4kiB of PCI config space.
All these platforms now have MMCONF_SUPPORT_DEFAULT.
Change-Id: If62537475eb67b7ecf85f2292a2a954a41bc18d1
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17545
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
MMCONF was explicitly used here to avoid races of 0xcf8/0xcfc access
being non-atomic and/or need to access 4kiB of PCI config space.
All these platforms now have MMCONF_SUPPORT_DEFAULT.
Change-Id: I943e354af0403e61263f1c780f02c7b463b3fe11
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17529
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Commit 36b81af (spi: Pass pointer to spi_slave structure in
spi_setup_slave) changes the way spi_setup_slave handles the spi_slave
structure. Instead of expecting spi controller drivers to maintain
spi_slave structure in CAR_GLOBAL/data section, caller is expected to
manage the spi_slave structure. This requires that spi_flash drivers
maintain spi_slave structure and flash probe function needs to make a
copy of the passed in spi_slave structure.
This change fixes the regression on Lenovo X230 and other mainboards.
Change-Id: I0ad971eecaf3bfe301e9f95badc043193cc27cab
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17728
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Iru Cai <mytbk920423@gmail.com>
Follow on patch to clean up the previous retry code.
Previous patches:
coreboot commit 079b5c65
(rockchip/rk3399: display: Retry edp initialization if it fails)
cros commit 28c57a6e
(rockchip/rk3399: display: retry edp initialization if edp initial fail)
- Reduce the jumping around via goto statements
- Break the retry code out into a separate function that also
prints the error messages.
BRANCH=gru
BUG=chrome-os-partner:60150
TEST=Rebuild Kevin and Gru
Change-Id: I3b6cf572073e4dcac83da09621bafde179af2613
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/17642
Tested-by: build bot (Jenkins)
Reviewed-by: Julius Werner <jwerner@chromium.org>
1. Define a new structure spi_ctrlr that allows platforms to define
callbacks for spi operations (claim bus, release bus, transfer).
2. Add a new member (pointer to spi_ctrlr structure) in spi_slave
structure which will be initialized by call to spi_setup_slave.
3. Define spi_claim_bus, spi_release_bus and spi_xfer in spi-generic.c
which will make appropriate calls to ctrlr functions.
BUG=chrome-os-partner:59832
BRANCH=None
TEST=Compiles successfully
Change-Id: Icb2326e3aab1e8f4bef53f553f82b3836358c55e
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17684
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
For spi_setup_slave, instead of making the platform driver return a
pointer to spi_slave structure, pass in a structure pointer that can be
filled in by the driver as required. This removes the need for platform
drivers to maintain a slave structure in data/CAR section.
BUG=chrome-os-partner:59832
BRANCH=None
TEST=Compiles successfully
Change-Id: Ia15a4f88ef4dcfdf616bb1c22261e7cb642a7573
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17683
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
1. Use size_t instead of unsigned int for bytes_out and bytes_in.
2. Use const attribute for spi_slave structure passed into xfer, claim
bus and release bus functions.
BUG=chrome-os-partner:59832
BRANCH=None
TEST=Compiles successfully
Change-Id: Ie70b3520b51c42d750f907892545510c6058f85a
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17682
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
TRAINING, not TARINING.
BUG=none
BRANCH=none
TEST=still builds
Change-Id: I8b7ffd0f0544a58865865a8b09d9c153db9c2674
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: b1ea846ce1ffd654d7d34c2a1d43b0fddbd4ae32
Original-Change-Id: I4940279ed7217cc20fe29c8b3603d1853acbfc5e
Original-Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/411801
Original-Commit-Ready: Patrick Georgi <pgeorgi@chromium.org>
Original-Tested-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Reviewed-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/17677
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
With addition of new features in VBT its size got increased
more than 6k and was unable to pass using mailbox 4 hence pass
using mailbox 3 to kernel.
BRANCH=none
BUG=chrome-os-partner:60026
TEST=firmware screen and Chrome OS screen should come up.
Change-Id: I359cf9bc402881161c9623cada689496716e04a5
Signed-off-by: Abhay Kumar <abhay.kumar@intel.com>
Reviewed-on: https://review.coreboot.org/17585
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
As per guidelines CPU security level should be dropped before OS start,
so that certain MSRs are locked out. Drop privilege levels on all logical
CPUs.
BUG=chrome-os-partner:60454
TEST=iotools rdmsr x 0x120, make sure bit 6 is set, rdmsr x 0x121 results
in io error.
Change-Id: I67540f6da16f58b822db9160d00b7a5e235188db
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/17665
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Currently we enable ACPI PM timer emulation only on BSP. So the timer
doesn't work on other cores and that breaks OSes that use it. Also,
microcode uses this information to figure out ACPI IO base, and that
is used for other features. This patch enables ACPI timer emulation
on all the logical CPUs.
BUG=chrome-os-partner:60011
TEST=iotools rdmsr x 0x121, x={0..3}, make sure it is set
Change-Id: I0d6cb8761c1c25d3a2fcf59a49c1eda9e4ccc70c
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/17663
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
In the ACPI header there's an OEM revision field that was previously
just being implicitly set to 0. Allow for a board to provide a
non-zero value for this field.
Change-Id: Icd40c1c162c2645b3990a6f3361c592706251f82
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/17650
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Instead of putting all the functions inline just put the
current implementation into a C file. That way all the implementation
innards are not exposed.
Lastly, fix up the fallout of compilation units not including the
headers they actually use.
Change-Id: I01fd25d158c0d5016405b73a4d4df3721c281b04
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/17648
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Instead of having callers query the romstage handoff resume
status by inspecting the object themselves add
romstage_handoff_is_resume() so that the same information
can be queried easily.
Change-Id: I40f3769b7646bf296ee4bc323a9ab1d5e5691e21
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/17647
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The same pattern was being used throughout the code base
for initializing the romstage handoff structure. Provide
a helper function to initialize the structure with the S3
resume state then utilize it at all the existing call sites.
Change-Id: I1e9d588ab6b9ace67757387dbb5963ae31ceb252
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/17646
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
In bootblock, cpu flex ratio is set to non-turbo max.
In FSP UPD, if CpuRatioOverride is zero, then it tries to program cpu
ratio to zero. Since it is different than the non-zero value programmed
in bootblock, FSP gives reset.
To avoid the reset, set FSP UPD for CPU flex ratio override to that
value as set in bootblock.
Change-Id: I8cae5530ec97cedfbd71771f291db6f55a9fd5c2
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/17555
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
FSP 2.0 implementation conditionally sets PMRR base based on
EnableC6Dram UPD. Therefore, handle the case of the PMRR base not being
set since FSP 2.0 changed behavior from FSP 1.1 implementation.
If prmrr base is non-zero value, then top_of_ram is prmrr base.
If Probeless trace is enabled, then deduct trace memory size from
calculated top_of_ram.
Change-Id: I2633bf78705e36b241668a313d215d0455fba607
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/17554
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
In FSP 2.0 the UPD to send extra VR Mailbox commands is switched from
SendVrMbxCmd to SendVrMbxCmd1. Use the same in silicon initialization.
Change-Id: I46bd50c9acc0456e2483f20ccb5e9ec2a0de232a
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/17578
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
1. Move existing IO decode range from pch_lpc_init to early
stage before SIO init.
2. At the same time, enable SIO decode range (0x2e/0x2f)
for platform which use super IO.
Change-Id: I72df16d0a784686d8cadfbee09b5aef60576ac43
Signed-off-by: Teo Boon Tiong <boon.tiong.teo@intel.com>
Reviewed-on: https://review.coreboot.org/17337
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Legacy PME are enabled by default in FSP UPD region.
When Legacy PME is enabled, then an SCI is generated and should be
handled by OS and BIOS/Coreboot in collboration. OS requires some
ACPI methods (eg _L69) which help to determine the wake source and also
to clear some registers. But this infrastructure is not present as of
now in coreboot and also linux handles PMEs natively.
Hence the SCI was never handled by OS and the status bits were never
cleared i.e., PCI_EXP_STS.
For this reason the level triggered SCI will remain active and the
system will wake up as soon as it enters S3.
To fix this, diabled Legacy PME (PmSci for Root ports).
Change-Id: I61317eb45305bdb14be3cc1a54fd9961d6ed593e
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/17553
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Apollolake MRC cache is divided into two regions: constant and variable.
Currently they are clubbed together. Since variable data changes across
cold reboot it triggers invalidation of the whole cache region. This
change declubs the data, adds routines to load/store variable data on
flash.
BUG=chrome-os-partner:57515
TEST=with patch series applied: cold reboot, make sure MRC is not
updated. Do S3 suspend/resume cycle.
Change-Id: I374519777abe9b9a1e6cceae5318decd405bb527
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/17237
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Piggy-back on existing MRC cache infrastructure to store variable MRC data.
Only one set of data can be valid at given point of time. Currently this
magically happens because region alignment is forced to 0x1000 and region
itself is of the same size. This needs to be somehow programmatically
enforced.
Change-Id: I8a660d356ca760b8ff9907396fb9b34cb16cf1db
Signed-off-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-on: https://review.coreboot.org/17320
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
We found that sometimes the edp doesn't get the edid or that video
config fails on kevin after a reboot. Now we will retry 3 times to
initialize it if there are errors.
BRANCH=gru
BUG=chrome-os-partner:60150
TEST=reboot kevin, the edp initialization error is no longer seen.
Change-Id: I96e20e526294fbc856fbdffcbd63accdc7371ef6
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 28c57a6e5b89c7b3a96204ec19a080067460544a
Original-Change-Id: I1382cdf4119fc4eeae5c2b36485030e3a38c2d91
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/412622
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/17626
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Current implementation checks for CONFIG_BOOTBLOCK_CONSOLE and then
initializes UART. If only CONFIG_BOOTBLOCK_CONSOLE
is enabled without enabling CONFIG_UART_DEBUG, there are
compilation issues. This is the case when using SIO UART for Skylake
DT platform. Hence initialize UART when CONFIG_UART_DEBUG is enabled
and not based on CONFIG_BOOTBLOCK_CONSOLE.
Also move BOOTBLOCK_CONSOLE out from UART_DEBUG to CPU_SPECIFIC_OPTIONS
as part of the fix needed.
Change-Id: Id422a55a68d64a06fc874bddca46b0ef5be6d596
Signed-off-by: Teo Boon Tiong <boon.tiong.teo@intel.com>
Reviewed-on: https://review.coreboot.org/17349
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Asserts are only fatal if CONFIG_FATAL_ASSERTS is enabled in Kconfig.
By default this is disabled, so the assert is generally just a printf.
Die if someone decides to pass in an invalid bus number for some reason.
Addresses coverity issue 1349858 - Out-of-bounds read
Signed-off-by: Martin Roth <martinroth@google.com>
Change-Id: I9d79bc336cbbfde31f655cfd271f101e7a90ab1b
Reviewed-on: https://review.coreboot.org/17484
Reviewed-by: Nico Huber <nico.h@gmx.de>
The lb_serial structure had some new entries added, which were not being
filled in.
Fill in the values so they're not undefined.
Addresses coverity error 1354778 - Uninitialized scalar variable
Change-Id: Ia7ce07f6e4e058c91c2e063f3225497271ef93ff
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/17482
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.h@gmx.de>
Define early smbus functions that can be used by mainboard to fetch spd.
Change-Id: Id170b2b8e6fb3ebb147f37bf433a27d1162dc11c
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/17433
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
FPR is an attribute of the SPI flash component and not of the SPI bus
itself. Rename functions, file names and Kconfig option to make sure
this is conveyed correctly.
BUG=None
BRANCH=None
TEST=Compiles successfully.
Change-Id: I9f06f1a8ee28b8c56db64ddd6a19dd9179c54f50
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17560
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
flash_programmer_probe is a property of the spi flash driver and does
not belong in the spi_slave structure. Thus, make
spi_flash_programmer_probe a callback from the spi_flash_probe
function. Logic still remains the same as before (order matters):
1. Try spi_flash_programmer_probe without force option
2. Try generic flash probing
3. Try spi_flash_programmer_probe with force option
If none of the above steps work, fail probing. Flash controller is
expected to honor force option to decide whether to perform specialized
probing or to defer to generic probing.
BUG=None
BRANCH=None
TEST=Compiles successfully
Change-Id: I4163593eea034fa044ec2216e56d0ea3fbc86c7d
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17465
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
max_transfer_size is a property of the SPI controller and not of the spi
slave. Also, this is used only on one SoC currently. There is no need to
handle this at the spi flash layer.
This change moves the handling of max_transfer_size to SoC SPI driver
and gets rid of the max_transfer_size parameter.
BUG=None
BRANCH=None
TEST=Compiles successfully.
Change-Id: I19a1d0a83395a58c2bc1614b24518a3220945a60
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17463
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
RW flag was added to spi_slave structure to get around a requirement on
some AMD flash controllers that need to group together all spi volatile
operations (write/erase). This rw flag is not a property or attribute of
the SPI slave or controller. Thus, instead of saving it in spi_slave
structure, clean up the SPI flash driver interface. This allows
chipsets/mainboards (that require volatile operations to be grouped) to
indicate beginning and end of such grouped operations.
New user APIs are added to allow users to perform probe, read, write,
erase, volatile group begin and end operations. Callbacks defined in
spi_flash structure are expected to be used only by the SPI flash
driver. Any chipset that requires grouping of volatile operations can
select the newly added Kconfig option SPI_FLASH_HAS_VOLATILE_GROUP and
define callbacks for chipset_volatile_group_{begin,end}.
spi_claim_bus/spi_release_bus calls have been removed from the SPI flash
chip drivers which end up calling do_spi_flash_cmd since it already has
required calls for claiming and releasing SPI bus before performing a
read/write operation.
BUG=None
BRANCH=None
TEST=Compiles successfully.
Change-Id: Idfc052e82ec15b6c9fa874cee7a61bd06e923fbf
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17462
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Make MMCONF_SUPPORT selected with MMCONF_SUPPORT_DEFAULT.
Platforms that remain to have explicit MMCONF_SUPPORT are
ones that should be converted.
Change-Id: Iba8824f46842607fb1508aa7d057f8cbf1cd6397
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17527
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Stage cache will save ~20ms on S3 resume for apollolake platforms.
Implementing the cache in ramstage to save silicon init and reload
it on resume. This patch adds passing S3 status to silicon init in
order to verify that the wake is from S3 and not for some other
reason. This patch also includes changes needed for quark and
skylake platforms that require fsp 2.0.
BUG=chrome-os-partner:56941
BRANCH=none
TEST=built for reef and tested boot and S3 resume path saving 20ms
Change-Id: I99dc93c1d7a7d5cf8d8de1aa253a326ec67f05f6
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/17460
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The wrong value was used for reporting an error when a requested
bus speed was made that isn't supported. Use the requested value.
Change-Id: I6c92ede3d95590d95a42b40422bab88ea9ae72a1
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/17474
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
If the SoC clock speed is not supported there is supposed to
be an error printed. However, the value printed was wrong which
was dereferencing a NULL struct. Fix that.
Change-Id: I5021ad8c1581d1935b39875ffa3aa00b594c537a
Found-by: Coverity Scan #1365977
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/17468
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Align top of stack to 8 bytes, value documented as FSP1.1 requirement.
Also fix some cases of uintptr_t casted to unsigned long.
Change-Id: I5bbd100eeb673417da205a2c2c3410fef1af61f0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/17461
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This changes the 933 DPLL rate to 928 which has low jitter.
BRANCH=none
BUG=chrome-os-partner:57845
TEST=boot kevin and run
while true; do sleep 0.1; memtester 500K 1 > /dev/null; done
for several hours
Change-Id: I4d2a8871aaabe3b0a1a165c788af265c5f9e892c
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 54ebf8763bb8193c4b36a5e86f0c625b176d31a6
Original-Change-Id: Iaa12bf67527b6d0e809657c513b8d1c66af25174
Original-Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/404550
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/17379
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
The Kevin project has been too smooth and boring for our tastes in the
last last few weeks, so we've decided to stir the pot a little bit and
reshuffle all our PLL settings at the last minute. The new settings
match exactly what the Linux kernel expects on boot, so it doesn't need
to reinitialize anything and risk a glitch.
Naturally, changing PLL rates will affect child clocks, so this patch
changes vop_aclk (192MHz -> 200MHz, 400MHz in the kernel), pmu_pclk
(99MHz -> 96.57MHz) and i2c0_src (198MHz -> 338MHz, leading to an
effective I2C0 change 399193Hz -> 398584Hz).
BRANCH=gru
BUG=chrome-os-partner:59139
TEST=Booted Kevin, sanity checking display and beep. Instrumented
rockchip_rk3399_pll_set_params() in the kernel and confirmed that GPLL,
PPLL and CPLL do not get reinitialized anymore (with additional kernel
patch to ignore frac divider when it's not used). Also confirmed that
/sys/kernel/debug/clk_summary now shows pclk_pmu_src 96571429 because
the kernel doesn't even bother to reinitialize the divisor.
Change-Id: Ib44d872a7b7f177fb2e60ccc6992f888835365eb
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 9b82056037be5a5aebf146784ffb246780013c96
Original-Change-Id: Ie112104035b01166217a8c5b5586972b4d7ca6ec
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/405785
Original-Commit-Ready: Xing Zheng <zhengxing@rock-chips.com>
Original-Tested-by: Xing Zheng <zhengxing@rock-chips.com>
Original-Reviewed-by: Xing Zheng <zhengxing@rock-chips.com>
Original-Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-on: https://review.coreboot.org/17378
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
The DDR speed Kconfig symbols needed to either be added to the Kconfig
tree, or have the code associated with them removed. I chose to add
the symbols.
- Add symbols for DDR333 - DDR667 to cygnus Kconfig. These should be
selected by the mainboard.
- Rename symbols from DDRXXX to CYGNUS_DDRXXX to match the existing
CYGNUS_DDR800 symbol.
- Rename the non Kconfig #define CONFIG_DRAM_FREQ to CYGNUS_DRAM_FREQ
because having other #defines look like Kconfig symbols is confusing.
- Change #ifdef CONFIG_DDRXXX to use IS_ENABLED
Change-Id: I3f5957a595072434c21af0002d57ac49b48b1e43
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/17386
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Daisuke Nojiri <dnojiri@chromium.org>
Before the PcdeMMCBootMode in the Updatable Product Date was always
assigned and didn't take into account the + 1 increment for the default
define.
Now if the configuration indicates that the device tree should be
followed PcdeMMCBootMode is initially disabled. Else if configuration
isn't the default, assign the value with the + 1 increment substracted.
TEST=Intel/MinnowMax
Change-Id: I6755eb585d1afe3a15f83347fba834766eb44ad2
Signed-off-by: David Imhoff <dimhoff_devel@xs4all.nl>
Reviewed-on: https://review.coreboot.org/10165
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Log the values of PcdEnableLpe and PcdeMMCBootMode even if they are
outside of the expected range.
TEST=Intel/MinnowMax
Change-Id: Ie0aea4287234b23d4e9852f3991dcc78ce8103d9
Signed-off-by: David Imhoff <dimhoff_devel@xs4all.nl>
Reviewed-on: https://review.coreboot.org/10164
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
BIOS needs to ensure that SPI write does not cross 256-byte
boundary. Else, if the write is across 256-byte boundary, then it
corrupts the block by wrapping write to start of current block. Thus,
ensure nuclear_spi_{read,write} operate within a single 256-byte block
only at a time.
BUG=chrome-os-partner:59813
BRANCH=None
TEST=Verified that elog writes do not corrupt the event log when write
is across 256-byte blocks.
Change-Id: I854ca2979d65b9f1232f93182cb84d4dee4f4139
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17419
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The Kconfig symbol CONSOLE_SERIAL_TEGRA210_UART_CHOICES was attached to
a choice, and isn't used anywhere. Remove it as unnecessary.
Change-Id: I4efd2e43ac34b266db0d40d1bc8c123bd377b3a2
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/17391
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This patch adds punit initialization code after
FspMemoryInit so that turbo can be initialized after
that.
BUG=chrome-os-partner:58158
BRANCH=None
Change-Id: I4939da47da82b9a728cf1b5cf6d5ec54b4f5b31d
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/17203
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
To avoid garbage display in firmware on warm reset, we need
to enable eDP display in depthcharge instead when the framebuffer is
cleared.
Therefore limit edp_enable() in coreboot to just configure eDP,
and leave enabling the display to depthcharge.
CQ-DEPEND=CL:402071
BUG=chrome-os-partner:58675
BRANCH=none
TEST=Boot from kevin, and display work
Change-Id: I9d937ead33ebba58e33e02fd73b80d6e11bb69aa
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 38b0d18c3fae37dfccb18fe809f763b98703167c
Original-Change-Id: Ibbc283a5892b98f4922f02fd67465fe2e1d01b71
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/402095
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/17207
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
This patch reduces the thermal time window to 100 milliseconds
for fast throttling action at prochot.
BUG=chrome-os-partner:59397
BRANCH=None.
TEST=Built for skylake platform and verified the thermal time
window value.
Change-Id: If79d213cb8e19277ffdb882267d2f8672df93446
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/17384
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
If the boot media is memory mapped temporarily mark it as write
protect MTRR type so that memory-mapped accesses are faster.
Depthcharge payload loading was sped up by 75ms using this.
BUG=chrome-os-partner:56656,chrome-os-partner:59682
Change-Id: Iba87a51a05559d81b8e00fa4f6824dacf7a661f5
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/17372
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Andrey Petrov <andrey.petrov@intel.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The default register count calculations are leading to higher
frequencies than expected. Provide an alternative method for
calculating the register counts by utilizing the rise and
fall times of the bus. If the rise time is supplied the
rise/fall time values are used, but the register overrides
take precedence over the rise/fall time calculation. This
allows platforms to choose whichever method works the best.
BUG=chrome-os-partner:58889
Change-Id: I7747613ce51d8151848acd916c09ae97bfc4b86a
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/17350
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
The apollolake and skylake had duplicate stanzas of code for
initializing the i2c buses. Additionally, they also had very
similar structures for providing settings for the i2c speed
control. Introduce a new struct lpss_i2c_bus_config and
utilize it in both apollolake and skylake thereby removing
the need for SoC-specific structres. The new structure is
used for initializing a bus fully as the lpss i2c API is
simplified in that lpss_i2c_init() is only required to be
called. The struct lpss_i2c_bus_config structure is passed
in for both initializing and filling in the SSDT information.
The formerly exposed functions are made static to reduce the
external API exposure.
BUG=chrome-os-partner:58889
Change-Id: Ib4fa8a7a4de052da75c778a7658741a5a8e0e6b9
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/17348
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
In preparation of merging the lpss i2c config structures on
apollolake and skylake move the i2c voltage variable to its
own field. It makes refactoring things easier, and then there's
no reason for a separate SoC specific i2c config structure.
BUG=chrome-os-partner:58889
Change-Id: Ibcc3cba9bac3b5779351b673bc0cc7671d127f24
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/17347
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
1. Re-factor MRC cache driver to properly select RW_MRC_CACHE or
RECOVERY_MRC_CACHE based on the boot mode.
- If normal mode boot, use RW_MRC_CACHE, if available.
- If recovery mode boot:
- Retrain memory if RECOVERY_MRC_CACHE not present, or recovery is
requested explicity with retrain memory request.
- Use RECOVERY_MRC_CACHE otherwise.
2. Protect RW and RECOVERY mrc caches in recovery and non-recovery boot
modes. Check if both are present under one unified region and protect
that region as a whole. Else try protecting individual regions.
3. Update training data in appropriate cache:
- Use RW_MRC_CACHE if normal mode.
- Use RECOVERY_MRC_CACHE if present in recovery mode. Else use
RW_MRC_CACHE.
4. Add proper debug logs to indicate which training data cache is used
at any point.
BUG=chrome-os-partner:59352
BRANCH=None
TEST=Verified that correct cache is used in both normal and recovery
mode on reef.
Change-Id: Ie79737a1450bd1ff71543e44a5a3e16950e70fb3
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17242
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
chip.h has a config array PcieRpClkReqNumber which corresponds
to a FSP UPD parameter, the size is currently set to 20.
However the size of PcieRpClkReqNumber UPD in FSP2.0 is 24,
so memcpy (config buffer to UPD buffer) in chip_fsp20.c will read
beyond the bounds of config array.
Hence set the size of PcieRpClkReqNumber array based on the FSP in use.
Found-by: Coverity Scan #1365385, #1365386
Change-Id: I937f68ef33f218cd7f9ba5cf3baaec162bca3fc8
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-on: https://review.coreboot.org/17292
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch updates below info,
[1] Delete the DPTF_CPU_ACTIVE_AC* values because these are not
being used. Hence, removing unnecessary defines.
[2] Add new DPTF_TSR0_ACTIVE_AC* temperature trip points for TSR0
external thermal sensor. These trip points are being used by _ACx
methods to control the fan speed on Skylake-U fan based Lars and
Kunimitsu platforms.
[3] Follow up patches are using DPTF_CPU_ACTIVE_AC* temperature trip
points in board specific acpi/dptf.asl (for lars, kunimitsu, etc) to
control the fan speed as per the CPU temperature trip points.
[4] Newly added _ACx methods for thermal sensor TSR0 in this patch
has nothing to do with DPTF_CPU_ACTIVE_AC*.
We can control fan speed using various different thermal sensors.
In this patch, we have added new _ACx methods for TSR0 thermal sensor.
We run the fan at different speeds to cool down the system at different
TSR0 temperatures.
Similarly, we considered CPU sensor temperature values and ran the fan
at different speeds to cool down the system.
BUG=chrome-os-partner:51025
BRANCH=firmware-glados-7820.B
TEST=Built and booted on kunimitsu and lars EVT boards.
Verified these _ACx methods with _ART table on these boards
with different workloads.
Change-Id: Ia7b81e03da936c4a0f69057e43f18efd7c3b9f17
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://chromium-review.googlesource.com/332368
Reviewed-on: https://review.coreboot.org/17067
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
When doing long transcations on an I2C bus at standard speed we saw
that long transactions could go over the 4ms limit while waiting for
it to complete on the bus.
Increase this so we can use standard speed for testing and debug in
firmware. (as there is no way to force standard speed in the kernel)
BUG=chrome-os-partner:58666
TEST=boot eve board with cr50 TPM and I2C bus at 100khz
Change-Id: I2987ae6a5aa024b373eb088767194c70b0918b6f
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/17213
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
When reading+clearing a GPE for use as an interrupt we need to
re-read the status register and keep setting the clear bit until
it actually reads back clear. Also add a 1ms timeout in case the
status never clears.
This is needed if a device sends a longer interrupt pulse and it
is still asserted when the "ISR" goes to clear the status.
BUG=chrome-os-partner:59299
TEST=test cr50 TPM with 20us pulse to ensure it can successfully
communicate with the TPM and does not get confused due to seeing
interrupts that it should not.
Change-Id: I384f484a1728038d3a355586146deee089b22dd9
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/17212
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
A dedicated pmc_ipc DSDT entry is required for pmc_ipc kernel driver.
The ACPI mode entry includes resources for PMC_IPC1, SRAM, ACPI IO and
Punit Mailbox.
BRANCH=None
BUG=chrome-os-partner:57364
TEST=Boot up into OS successfully and check with dmesg to see the
driver has been loaded successfully without errors.
Change-Id: Ib0a300febe1e7fc1796bfeca1a04493f932640e1
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/17181
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
SATA device remains unrecognized if connected at Port 2.
Port control and Status register (PCS) is by default set by
hardware to the disabled state as a result of an initial
power on reset. OS read PCS register during boot causes
disabling of SATA ports and can't detect any devices.
BRANCH=none
BUG=chrome-os-partner:59335
TEST=Build and boot SKL from SATA device connected at Port 2.
Change-Id: I4866ca44567f5024edaca2d48098af5b4c67a7ac
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/17229
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Avoid use of Local0 variable in TEVT acpi method.
If mainboard doesn't expose any thermal sensor, then warning is
generated for variable Local0 not been used.
Change-Id: I0634961a01144e41a8480c8c6ed8b7fdd358e768
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/17245
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Add device id for PCH-Y used in Kaby Lake RVP3 board.
Change-Id: I9235265cf88e4d044e7216f53e6da7021fb68238
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/17244
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Log when the MRC cache is attempted to be updated with status
of success or failure. Just one slot is supported currently
which is deemed 'normal'. This is because there are more slots
anticipated in the future.
BUG=chrome-os-partner:59395
Change-Id: I0f81458325697aff9924cc359a4173e0d35da5da
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/17231
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins)
Fix msch ddrconfig register write error. Also make sure that the row
number configured in msch is equal to the row number configured in the
DDR controller.
This would not affect systems with 4GB of memory, but is needed
for 2GB configurations.
BUG=None
BRANCH=None
TEST=Boot from kevin
Change-Id: Ic95b3371faec5b31c32b011c50e55e83d949e74d
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: dfa43d3d44839d9685b6393157f51b646e9996de
Original-Change-Id: I0c95378bf937a245b7cdc0583c5d2ed1347f2a3e
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/399563
Original-Reviewed-by: Derek Basehore <dbasehore@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/17208
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
This was a dummy implementation until now which returned -1 always. Add
support for reading SPI flash status register (srp0).
BUG=chrome-os-partner:59267
BRANCH=None
TEST=Verified by enabling and disabling write-protect on reef that the
value of SRP0 changes accordingly in status register read.
Change-Id: Ib1349605dd87c4a087e416f52a8256b1eaac4f4c
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17205
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Monitor/Mwait is broken on APL. So, it needs to be disabled.
BUG=chrome-os-partner:56922
BRANCH=None
Change-Id: I12cd4280de62e0a639b43538171660ee4c0a0265
Signed-off-by: Venkateswarlu Vinjamuri <venkateswarlu.v.vinjamuri@intel.com>
Reviewed-on: https://review.coreboot.org/17200
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
framebuffer address is dynamically chosen by libpayload now, so there's
no need to configure it in coreboot.
CQ-DEPEND=CL:401402
BUG=chrome-os-partner:58675
BRANCH=none
TEST=Boot from kevin, dev screen is visible
Change-Id: I9f1e581d5c63b3579b26be22ce5c8d1e71679f6f
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: b3b6675420592c30e1e0abc8f8e9dd6ed5abd04c
Original-Change-Id: I7e3162f24a4dc426fe4e10d74865cf0042c80db5
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/401401
Original-Commit-Ready: Julius Werner <jwerner@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/17109
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Near the end of DDR initialization, the system switches to the index1
configuration. Sometimes this failed and a status bit that coreboot was
waiting for was never set, hanging the system.
Instead, give the system 100ms to reach the new configuration or reboot
it, which generally fixes the issue. Also reset when training the index1
configuration fails.
BUG=chrome-os-partner:57988
BRANCH=None
TEST=The error condition now leads to a reboot of coreboot which
recovers the system, instead of hanging.
Change-Id: Icb4270369102ff7a4ce91b0677e04b4eb10f1204
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: ca250d0628ea3b6b39d5131246eaba68637c5140
Original-Change-Id: Id6e8936d90e54b733ac327f8476d744b45639232
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/399681
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/17106
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
1. Update write leveling value to 0x200.
When the wrdqs slave delay is changed to 0x200, the phase between the
dqs and the clock is 0 degrees. The pcb layout can make sure the tDQSS
timing is smaller than 0.25tck, so this value is useful for both higher
and lower frequencies.
2. Disable read leveling for LPDDR3.
The read leveling result is unreliable - the value is not in the middle
of the read eye. To fix this, disable read leveling and fix the read
DQSn slave delay setting for DQn to 0x080 (1/4 cycle delay of the
input signal).
BUG=None
BRANCH=None
TEST=Boot from kevin; Check by shmoo read eye and stability test, that
the updated value of 0x80 is better.
Change-Id: Ia72b601d9bf4e34ba1b0b4584b2c5c3ce9dafbd4
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 37e8dfe783db3ce71aa026b4609ed0bfa16db06f
Original-Change-Id: I2a5d40c0348449b2a7c609c1db65da4ed5f1c09f
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Signed-off-by: Jeff Chen <cym@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/396598
Original-Commit-Ready: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Derek Basehore <dbasehore@chromium.org>
Reviewed-on: https://review.coreboot.org/17105
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
To enable DDR Dynamic Voltage and Frequency Scaling (DVFS) we need to
train alternative configurations first, so do the training and store the
values.
BUG=None
BRANCH=None
TEST=Boot from kevin
Change-Id: I944a4b297a4ed6966893aa09553da88171307a42
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: 94533ff3ba21bcb0ace00bedcf0cebb89a341be2
Original-Change-Id: I4a98bc0db5553d154fedb657e35b926a92aa80c7
Original-Signed-off-by: Lin Huang <hl@rock-chips.com>
Original-Reviewed-on: https://chromium-review.googlesource.com/386596
Original-Commit-Ready: Douglas Anderson <dianders@chromium.org>
Original-Reviewed-by: Derek Basehore <dbasehore@chromium.org>
Original-Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/17104
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martinroth@google.com>
Testing for "devfn < 0" on an unsigned doesn't work, and i2c_bus_to_devfn
returns an int (with -1 for "error"), so use int for devfn.
Adapt Change-Id I7d1cdb6af4140f7dc322141c0c018d8418627434 to fix more
instances.
Change-Id: I001a9b484a68e018798a65c0fae11f8df7d9f564
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Found-by: Coverity Scan #1357450, #1357449
Reviewed-on: https://review.coreboot.org/17054
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Some of our RK3399 devices have panel resolutions as high as 2400x1600.
With 16bpp that barely still fit into an 8MB framebuffer, but then we
changed it to 32bpp for better image quality...
Note that this is a band-aid. Coreboot-allocated framebuffers shouldn't
be used at all on ARM64 devices, since libpayload is perfectly capable
to dynamically allocate it with the right size based on EDID-information
on this architecture. That will require some more elaborate work to be
fixed with later patches.
BRANCH=gru
BUG=chrome-os-partner:58044
TEST=Warm-reboot Kevin on the dev screen, confirm that you don't see the
lower half of the screen that overflowed our allocated framebuffer
preserved from the last boot as soon as the backlight turns on.
Change-Id: I00a63cfef35a8ee734543abbdb298344fb529283
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Original-Commit-Id: d2718efcacb50371624d9f6a3b586c298e8c2fec
Original-Change-Id: Ia1fa28971c65d7d0639966e715f742309245172b
Original-Signed-off-by: Julius Werner <jwerner@chromium.org>
Original-Reviewed-on: https://chromium-review.googlesource.com/399966
Original-Reviewed-by: Daisuke Nojiri <dnojiri@chromium.org>
Reviewed-on: https://review.coreboot.org/17108
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
All current implementations of ramstage_cache_invalid() were just
resetting the system based on the RESET_ON_INVALID_RAMSTAGE_CACHE
Kconfig option. Move that behavior to a single implementation
within prog_loaders.c which removes duplication.
Change-Id: I67aae73f9e1305732f90d947fe57c5aaf66ada9e
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/17184
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
ramstage_cache_invalid which was added in
I83fe76957c061f20e9afb308e55923806fda4f93 (review.coreboot.org/#/c/17112)
requires hard_reset to be defined in postcar stage.
BUG=None
BRANCH=None
TEST=Compiles successfully for reef.
Change-Id: I283277c373259e0e2dfe72e3c889ceea012544f2
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/17182
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins)
While using '3' is fine for the standard gpe0 for skylake, I want
to make sure anyone that copies this code doesn't tweak GPE0_REG_MAX
without the hard coded index. If that does happen now things will
still work, but it may just not match the hardware proper.
BUG=chrome-os-partner:58666
Change-Id: I434b9a765a0a2f263490bb2b4ecb3635292d46c9
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/17160
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Add a GPIO macro that allows a pin to be routed to the APIC with
the input inverted. This allows a normal interrupt to get used as
a GPE during firmware and still be used as a perhiperal interrupt
in the kernel.
BUG=chrome-os-partner:58666
TEST=boot en eve and use TPM IRQ in firmware and OS
Change-Id: I77f727f749fdd5281ff595a9237fe1e634daba96
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/17176
Tested-by: build bot (Jenkins)
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Add the necessary infrastructure to support eSPI SMI events,
and a mainboard handler to pass control to the EC.
BUG=chrome-os-partner:58666
TEST=tested on eve board with eSPI enabled, verified that lid
close event from the EC during firmware will result in an SMI
and shut down the system.
Change-Id: I6367e233e070a8fca053a7bdd2534c0578d15d12
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/17134
Tested-by: build bot (Jenkins)
Reviewed-by: Furquan Shaikh <furquan@google.com>
Furquan Shaikh