This board uses the reset defaults for DxxIP and DxxIR.
The datasheet "Intel ® I/O Controller Hub 10 (ICH10) Family"
mistakenly says in the D31IP register that all function have INTB as
default. This is however not true as documented in the reset default
value.
This fixes the DSDT such that the SMBus device gets a route for the
INT C interrupt it uses.
Change-Id: I3dd1308fb7acec86b90ecd9d2079cf9a58702c40
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/21442
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
TESTED: NGI works on VGA with adapter on DVI-I port
Change-Id: I4bd9d451295d26a3e11ded9863f5d45d42c8fead
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/21441
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This makes the VGA output on the DVI-I connector usable.
This reuses vendor settings.
Change-Id: Ib8b6bf33816f7e468a09ff5e2008c2cb9f7c0a8b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/21440
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
For boards with cimx/sb800, mainboards defined only empty
stubs. Reset functionality is handled as BiosCallout.
For amd/inagua, the defined function was actually initial
GPIO programming.
For cimx/sb700, function had prototypes but no callers.
For cimx/sb900, everything was commented out already.
Change-Id: I936feb4fc41d903078620c919a733bb9f39c3efb
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21477
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Because cpu/intel/car/romstage.c assumes a 8KiB stack size
when setting up stack guards, and all Slot 1 compatible
CPUs have enough L1 cache available for the increase.
Adjust DCACHE_RAM_BASE to match.
Boot tested on asus/p2b-ls and asus/p3b-f using a 1400MHz
Tualeron. The latter actually requires this patch to boot
successfully.
Change-Id: I5b440e7be4f3149378db88872872012c92049c20
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/21349
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Make all CAR-related calculations refer to CONFIG_DCACHE_RAM_BASE
and CONFIG_DCACHE_RAM_SIZE for consistency.
Do not set %ebp before and switch directly to stack returned by
romstage_main().
Remove an unneeded 4-byte gap in CAR stack.
The caching strategy for flash XIP area should be WRPROT.
Clarify the various comments in the file on the logic.
Together they lay the groundwork for bringing EARLY_CBMEM_INIT to
intel/slot_1 boards.
Change-Id: Ibb6cf6a2adbe3a1f28bf2903d852ddc19e09b484
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/21503
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Remove CAR testing code currently blocked out by #if. Newer CAR code
don't even do it anymore.
Change-Id: I2d53b4e7a244824c7aa2c0f597ed91e17f6cc668
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/21502
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Remove Hyperthreading related code that was missing setup of SIPI
vector and did not work.
Change-Id: I27e329a7b667ce4405fe07a637edbc6b5be22f2d
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/21375
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
* Add support for detecting WWAN.
* Allows to turn off power to WWAN if no card is installed.
Add the following devicetree values:
* has_wwan_detection
Set to one to indicate that the following register are sane.
* wwan_gpio_num
SB GPIO num to read.
* wwan_gpio_lvl
SB GPIO level for card to be present (usually zero).
Don't enable WWAN power if no card is detected.
As there are no devicetree values yet, the new code doesn't have any effect.
Change-Id: Ie53275b384c85df8adf71fe79b3d54211c868756
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/20983
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Add support for BDC detection, based on the schematics for each board.
Support for boards without schematics needs further testing.
Needs test on all boards.
Change-Id: If33ef88fb808f36b050393fa83eb1b541ce936b9
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/19810
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
Move rtc init code into common area and update the implementation for
apollolake to avoid build break.
Change-Id: I702ce0efba25cb6fde33cc15698ae44312742367
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/21433
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The RO_VPD region is required for ChromeOS.
BUG=b:65408869
TEST=Build and check coreboot.rom with fmap_decode.
Change-Id: I9c475acc5e34a3a41f815990fb1f363963c7b9b9
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/21473
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The original purpose of adjust_cpu_apic_entry() was to set
up an APIC map. That map was effectively only used for mapping
*default* APIC id to CPU number in the SMM handler. The normal
AP startup path didn't need this mapping because it was whoever
won the race got the next cpu number. Instead of statically
calculating (and wrong) just initialize the default APIC id
map when the APs come online. Once the APs are online the SMM
handler is loaded and the mapping is utilized.
Change-Id: Idff3b8cfc17aef0729d3193b4499116a013b7930
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/21452
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
With AMD_INIT_ENV and AMD_INIT_S3LATERESTORE moved
from romstage to ramstage, heapamanager in romstage
is no longer needed.
Change-Id: Iea8ad3ddb245c83dd290436ac9d4ecac9350b88c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21454
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
CONFIG_MAINBOARD_VENDOR is customizable by OEM for Chrome OS
devices. However, VBOOT_FWID_MODEL indicates the firmware vendor and
hence if CHROMEOS is selected, then VBOOT_FWID_MODEL should always
prefix "Google_" instead of CONFIG_MAINBOARD_VENDOR.
BUG=b:65493192
Change-Id: I0a2280bfd6d535586bc14d9a3c4a8198287f08bc
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/21458
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
- Get rid of CONFIG_ prefix from variables that don't come from Kconfig.
- Remove 2nd set of variables that are duplicates of the first set.
- Delete duplicate set of Prerequisites
Change-Id: I194b4c790b3e35353d480d34b60507a00f10ef11
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/21451
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
- The SMU firmware used to be named *.sbin, now is named *.csbin.
Update the makefile so that the files can be named as they are
delivered and don't have to be renamed.
- Add a Kconfig option to allow the secure os binaries to be excluded.
BUG=b:64932297
TEST=Build with old and new firmware, verify file sizes.
Change-Id: I3091f8af126159488c3c398a6dc881fa05039cff
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/21450
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Adapted from Chromium commit 9756af8.
Add SOC helper to identify BSW SoC stepping. Will be used to
override USB2 phy setting based on stepping in subsequent commit.
Original-Change-Id: Ic736dd945f01cf9f24af4ce3bd3f2757abfdeb2e
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Tested-by: Keith Tzeng <keith.tzeng@quantatw.com>
Change-Id: Ib2371f85ea84df4b417e25ec8840d317cd918d5f
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/21371
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
With FSP 1.1, all FSP blobs are forward-compatible with newer FSP 1.1
header files, so adjust the header revision check to ensure that the
FSP blob isn't newer than the header, rather than an exact version match.
This resolves a version mismatch issue with Braswell ChromeOS devices,
which ship with FSP blobs newer than the publicly-released blob (1.1.2.0),
but older than the current Braswell FSP 1.1 header (1.1.7.0).
TEST: build/boot google/cyan and edgar boards, observe no adverse
effects from using current FSP header (1.1.7.0) with the factory-
shipped FSP blobs (1.1.4.0/1.1.4.2).
Change-Id: I8934675a2deed260886a83fa34512904c40af8e1
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/21369
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch adds the common acpi code.ACPI code is very similar
accross different intel chipsets.This patch is an effort to
move those code in common place so that it can be shared accross
different intel platforms instead of duplicating for each platform.
We are removing the common acpi files in src/soc/intel/common.
This removes the acpi.c file which was previously in
src/soc/common/acpi. The config for common acpi is
SOC_INTEL_COMMON_BLOCK_ACPI which can be defined in SOC's
Kconfig file in order to use the common ACPI code. This patch also
includes the changes in APL platform to use the common ACPI block.
TEST= Tested the patch as below:
1.Builds and system boots up with the patch.
2.Check all the ACPI tables are present in
/sys/firmware/acpi/tables
3.Check SCI's are properly working as we are
modifying the function to override madt.
4.Extract acpi tables like DSDT,APIC, FACP, FACS
and decompile the by iasl and compare with good
known tables.
5.Execute the extracted tables in aciexec to check
acpi methods are working properly.
Change-Id: Ib6eb6fd5366e6e28fd81bc22d050b0efa05a2e5d
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/20630
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
APL internal UARTs are not used on this mainboard.
Change-Id: I39118262fc6f37b45785538a3f2d1d31d42cbe86
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/21406
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
There is one on-board PCI device where bus master has to be enabled in
PCI configuration space. As there is no need for a complete PCI driver
for this device just set the bus master bit in mainboard_final().
Change-Id: I45202937eba11da3bea14fef6ebed70599804335
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/21405
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Boards with CBMEM_TOP_BACKUP=y can also use POSTCAR_STAGE
for MTRR setup after adding this file in the build.
Change-Id: I5f9a673ff59ccfbba16308d27f653f5cf3b49017
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21445
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Postcar failed when loading from stage_cache, if
romstage did not pass same pcf->stack on normal
and resume paths.
Change-Id: I853afb1fbdb942fd671d89950911c850c96e3af3
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/21444
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The change allows to update rmodule parameters after
it has been loaded from stage cache.
Change-Id: Ib825ffe245d447ad3a8246f7dbd52c6e34103a0c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/21385
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch implements soc function to get previous sleep state
using chipset_power_state global structure.
acpi_get_sleep_type is needed in PRE_RAM stage when soc selects
CONFIG_EARLY_EBDA_INIT kconfig option.
Change-Id: I79acbfc09c8d255fbf9d73e49e8c7764f3f3fac6
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/21423
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Fix the warnings of klocwork scan.
e.g. "Pointer 'dev' checked for NULL at line 158 will be dereferenced at line 159"
Change-Id: I6cc9c68652b074c666c86456183460ca38a886ed
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/21408
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
We've decided to move control for the 3.0V rail (technically 3.3V on
Scarlet, but who cares about millivolts) back to a GPIO on the AP for
Scarlet rev2. This patch adds the necessary code to enable it and make
ARM TF aware of its existence. Since the pin had previously not been
connected to anything, we shouldn't really need to guard this by board
ID... older Scarlets will just be twiddling an empty pin.
Change-Id: I6037aa486b50119f2c7b859b966cadc3686e3459
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/21328
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: David Schneider <dnschneid@chromium.org>
Vendorcode expects some DRAM controller registers to
be writable, but they are actually locked after soft
resets if C6 states are enabled.
Without the workaround, raminit fails on soft resets.
Change-Id: I6b9e275e11b2907d026c13341334983a4d9c8889
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21317
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
It's too critical to ignore when sending the message on
SMBus fails, so allow for a fair amount of retries.
Failure here causes watchdog to do hard reset later.
Move it out of mainboard.c as we need to call this
early in romstage while we are debugging.
Change-Id: I1006b079269d6dd44de630db7a5694124af2f974
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21316
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Fix regression caused by commit
9e94dbf ACPI: Get S3 resume state from romstage_handoff
Boards with EARLY_CBMEM_INIT are required to provide
romstage_handoff structure to signal S3 resume path.
Change-Id: I7c9065ccc48dfbdefade698ed275756f17dff7a0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21396
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Fix regression caused by commit
9e94dbf ACPI: Get S3 resume state from romstage_handoff
Boards with EARLY_CBMEM_INIT are required to provide
romstage_handoff structure to signal S3 resume path.
Change-Id: I464feb1655a51a937b6cf53508dd5c7aa0d8f791
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21395
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
Fix regression caused by commit:
714709f AMD fam10 ACPI: Use common fixed sleepstates.asl
Adding common sleepstates.asl got lost in rebase process.
Change-Id: I4f22ee950ae5637113db8e79ca238cb1b81002aa
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21413
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This patch adds imon and vmon slot numbers for Maxim 98927 driver.
These values are used to confiure IV feedback for audio playback on speakers.
BUG=b:36724448
TEST=After boot, the register dump for Max98927 codecs should have
imon and vmon slots numbers set in 0x1e register.
Change-Id: I4382da4f984507d147751c168e8177b58c88a70f
Signed-off-by: Harsha Priya <harshapriya.n@intel.com>
Reviewed-on: https://review.coreboot.org/21196
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This change list adds imon and vmon slot numbers as params for
Maxim 98927 driver. These values are looked up in the kernel driver
to confiure IV feedback for audio playback on speakers.
BUG=b:36724448
TEST=After boot, the register dump for Max98927 codecs should have
imon and vmon slots numbers set in 0x1e register.
Change-Id: I21d72ba91af83782587f11018b2d1d1c8d4f676c
Signed-off-by: Harsha Priya <harshapriya.n@intel.com>
Reviewed-on: https://review.coreboot.org/21195
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
There was already a uart.c added to bootblock. Remove the
duplicate addition.
Change-Id: I2d420ff7437d25a596ee9a120964f8d4bc413bc4
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/21410
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add Vboot and ChromeOS support in SOC Kconfig, include a separated
verstage in Makefiles.inc as well.
Change-Id: I114a9d6e92b69199ccacc1e7e1535eccc0e2cb99
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/21280
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
AGESA internal headerfiles are allover the place. Luckily, they
have unique names within the Proc/ tree so include every existing
directory in undefined order.
Change-Id: I86f080e514391a3f0f05d379d24d490ce075060e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21285
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
This reverts commit 6c0f3c7ee1.
Reason for revert:
Broke master builds, this was submitted out-of-order, some
of the dependencies have not passed review with +2 yet.
Change-Id: Ib7bcb1b98623d16e074caeca839a936d71ded709
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21414
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
This recovers FCH configuration on S3 resume path.
Appearst to work, but other defects of HAVE_ACPI_RESUME
must be fixed also before S3 support is re-enabled.
Change-Id: I8d07d2e9dc161b67d854fcc8ec1da1f36900f989
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21376
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
There is no serial port on this platform.
In addition, put the LPC serial IRQ into quiet mode.
Change-Id: I4b2c93c51e8ddb8b510f0d7f7e3072befeba5d95
Signed-off-by: Nicola Corna <nicola@corna.info>
Reviewed-on: https://review.coreboot.org/21226
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The deprecation of late (post-romstage) CBMEM initialization was
announced in this blog post:
https://blogs.coreboot.org/blog/2017/05/08/announcing-coreboot-4-6/
There are two warnings:
* In LATE_CBMEM_INIT's help text, I've added a multi-line warning, that
aims to explain the problem.
* In src/mainboard/Kconfig (just below the mainboard selection), there's
a warning which points the user at LATE_CBMEM_INIT, if such a board is
selected.
Also update the function that needs to be implemented, as pointed out by
Keith Hui and Kyösti Mälkki.
Change-Id: I2d21a6ab2fc2811d44fc4febb05841bb2f8d1857
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/21112
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Inspired by gm45 code, which sets this value the same way.
Some values for tRD on 800 and 1067MHz FSB were set wrong because the
CAS/Freq selection was wrong. CAS was often selected to low and when
fixing CAS this results in tRD being too high, due to an incorrect
lookup table which caused instability.
PASSED memtest86+ during 10h+ on 1067MHZ fsb with 667MHz ddr2, CAS 5
on GA-945GCM-S2L.
Change-Id: I8002daf25b7603131b78b01075f43fd23747dd94
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18354
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Also make most significant bit function accessible outside the scope
of this file.
Change-Id: I3ab39d38a243edddfde8f70ebd23f79ff774e90e
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18320
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
08f7d1ae0d ("mainboard/via*: Drop AMD car.h file") did the same for all
Via mainboards that were in tree at that time, but the winnet/g170 was
merged a bit later.
Change-Id: Iedb33f4c2fce6fc2cf2669fee4ffb25bf793c92b
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/21343
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Cherry-pick from Chromium 414024e.
Update the FSP 1.1 header to version 1.1.7.0, required for
susequent Chromium cherry-picks and to-be-merged Braswell CrOS devices.
As this header update doesn't shift offsets, only adds new fields
in previously unused/reserved space, it should not negatively impact
existing boards built against the older header version.
Original-Change-Id: Ic378b3c10769c10d8e47c8c76b8e397ddb9ce020
Original-Signed-off-by: Martin Roth <martinroth@google.com>
Original-Reviewed-by: Hannah Williams <hannah.williams@intel.com>
Original-Reviewed-by: Stefan Reinauer <reinauer@google.com>
Original-Tested-by: Martin Roth <martinroth@chromium.org>
Change-Id: Id33d41dee998cfa033264a98dfee40e2d8feead8
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/21368
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
__packed has been introduced in commit 6a00113de8
("Rename __attribute__((packed)) --> __packed"). Use it.
Change-Id: Ifd33129ae4fbe14c26ceeaaa88832ef994a32dfb
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/21393
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
__packed has been introduced in commit 6a00113de8
("Rename __attribute__((packed)) --> __packed"). Use it.
Change-Id: Ie654567ebff884b911de10bd9fef605436e72af8
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/21346
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
* Add support for detecting BDC.
* Allows to turn off power to BDC if no card is installed.
* Should fix https://ticket.coreboot.org/issues/99 .
Add the following devicetree values:
* has_bdc_detection
Set to one to indicate that the following register are sane.
* bdc_gpio_num
SB GPIO num to read.
* bdc_gpio_lvl
SB GPIO level for card to be present (usually zero).
Don't enable BDC power if no card is detected.
As there are no devicetree values yet, the new code doesn't
have any effect.
Change-Id: I506de2eca4b820e6d82de6b2c48a5440462e1db5
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/19809
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Alexander Couzens <lynxis@fe80.eu>
We now require EARLY_CBMEM_INIT and romstage_handoff to
support HAVE_ACPI_RESUME. Thus acpi_handoff_wakeup() would
never call an externally defined acpi_get_sleep_type().
Name _sleep_type() was also inapproriate here, as it referred
to hardware-dependent SLP_TYP field of PM1CNT but still
returned ACPI_Sx value instead.
Change-Id: I8dc130f1e86dd7e96922d546f0ae9713188336cd
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21397
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
This patch fixes klocwork bug due to recent memmap.c
implementation where “Pointer 'dev' returned from call
to function 'dev_find_slot' at line 144 may be NULL.”
Change-Id: I4c74ca410d1a0ba48634ec9928a0d9d1cc20e27a
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/21404
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This changelist adds the capture format to be set for max98927. The
nhlt blob is the same but the format params for capture are different
from the render.
BUG=b:36724448
TEST=IV feedback data is of good quality
Change-Id: I135cf4479e89cd2046ff46027f94c0f71aed650e
Signed-off-by: Harsha Priya <harshapriya.n@intel.com>
Reviewed-on: https://review.coreboot.org/21340
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Currently PMIC (tps68470) is in active state even when cameras are not
in use. PMIC is put into SLEEP mode only when entering S3 via
smihandler.
With this change PMIC will be put into SLEEP mode as soon as sensors &
VCM voltage outputs are turned off. This will allow run time power
saving when camera is not in use.
PMIC will be reset in first boot & across S3 & S0ix cycles.
Also, remove the smi handler for PMIC power management & handle it as
part of sensor and VCM ACPI PowerResource.
BUG=b:63903239
TEST= Build for Soraka. Check Camera probe, Capture image across
S3 & S0ix cycles.
Also checked the following & found no regression:
1. Typical camera use cases
2. Stability tests related to camera
3. Reliability tests related to camera
4. PnP tests related to camera
5. Latency related tests with camera
Change-Id: I23b0c0a887c9eb5d29b89f14aebba273b01228e0
Signed-off-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Signed-off-by: Naresh G Solanki <naresh.solanki@intel.com>
Reviewed-on: https://review.coreboot.org/20741
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rajmohan Mani <rajmohan.mani@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
GCC_PREFIX is uncommon in the coreboot tree. If not provided, take data
from .xcompile to fill in the blanks.
Change-Id: I711a73be9d35d896198664f0ae213218653f275e
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/21391
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
It's arch specific, so no need to pollute non-x86 with it.
Change-Id: I99ec76d591789db186e8a33774565e5a04fc4e47
Signed-off-by: Patrick Georgi <pgeorgi@chromium.org>
Reviewed-on: https://review.coreboot.org/21392
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The Harcuvar CRB is a reference platform of Intel Atom C3000 SoC
("Denverton" and "Denverton-NS") for the communications segment/market.
The MohonPeak coreboot was used as the starting template with
additions/modifications from other Intel Apollo Lake/Skylake coreboot.
Tested with TianoCore payload (UDK2015) and Poky (Yocto
Project Reference Distro) 2.0 with kernel 4.1.8 booted from
SATA drive and external USB pendrive.
Change-Id: I088833e36e2d22d1fe1610b8dca1454092da511a
Signed-off-by: Mariusz Szafranski <mariuszx.szafranski@intel.com>
Reviewed-on: https://review.coreboot.org/20862
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: FEI WANG <wangfei.jimei@gmail.com>
This change adds support for Intel Atom C3000 SoC
("Denverton" and "Denverton-NS").
Code is partially based on Apollo Lake/Skylake code.
Change-Id: I53d69aede3b92f1fe06b74a96cc40187fb9825f1
Signed-off-by: Mariusz Szafranski <mariuszx.szafranski@intel.com>
Reviewed-on: https://review.coreboot.org/20861
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: FEI WANG <wangfei.jimei@gmail.com>
We set the SPI lockdown in BS_POST_DEVICE (dev_finalize()) on many plat-
forms now. The SPI controller is initialized at start of BS_DEV_INIT
(dev_initialize()).
The SPI lockdown usually shouldn't be a problem but the SPI driver imple-
mentation lacks full support for the locked interface. Also, some options
exist to lock all flash regions read-only until the next reboot.
Change-Id: Ifda826ae2bb28adcce8dda8e2bb16dc38fe0fe9e
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/21326
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nicola Corna <nicola@corna.info>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Bill XIE <persmule@gmail.com>
Move ADD_VBT_DATA_FILE to "Devices" menu and rename it to
INTEL_GMA_ADD_VBT_DATA_FILE.
Depend on Intel platforms to avoid confusing users of non-Intel platforms.
The Intel GMA driver will use the vbt.bin, if present, to fill the
ACPI OpRegion.
Change-Id: I688bac339c32e9c856642a0f4bd5929beef06409
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/20619
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This patch adds the DPTF settings specfic to the mainboard and enables
the CPU and other thermal sensors as participant device for fizz.
It also enables the DPTF flag in the device tree for fizz.
BUG=b:64915426
BRANCH=None
TEST=emerge-fizz coreboot and run DPTF observation tool to make sure
DPTF is up and running.
Change-Id: Ic7d125a763f539158aa425fbba1d8a000a3465ca
Signed-off-by: Tsai, Gaggery <gaggery.tsai@intel.com>
Reviewed-on: https://review.coreboot.org/21147
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
We have no wacom digitizer on I2C#3, so remove it.
TEST=build and boot on soraka.
Change-Id: I3f5a1b9ece6fc9a9443477c7a7aa77dbcdf6a703
Signed-off-by: Wisley Chen <wisley.chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/21309
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The MPC.HPCE bit of the ExpressCard root port is not set in vendor
firmware, so autoport didn't generate the right pcie_hotplug_map to
support ExpressCard hotplug.
Also add comments for each PCIe root port.
Change-Id: Ic53e36a7192b9bfa8ff9fca57f4556e972e2611b
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/21310
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Previously, only when selecting GCC could any toolchain be
selected, this allows compiling with distro clang/llvm.
Change-Id: I2d9d02f360d54ed92d6b6f55e6fcd530aae79adb
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/21300
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Martin Roth <martinroth@google.com>
The addr32 prefix is required by binutils, because even when
given an explicit address which is greater than 64KiB, it will
throw a warning about truncation, and stupidly emit the opcode
with a 16-bit addressing mode and the wrong address.
However, in the case of LLVM, this doesn't happen, and is happy
to just use 32-bit addressing whenever it may require it. This
means that LLVM never really needs an explicit addr32 prefix to
use 32-bit addressing in 16-bit mode.
Change-Id: Ia160d3f7da6653ea24c8229dc26f265e5f15aabb
Also-by: Damien Zammit <damien@zamaudio.com>
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/21219
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Without this remapping code enabled, the system fails to boot properly
if the amount of ram inserted is larger than 4G minus the mmio
space (hardcoded to 1G here).
Change-Id: I02e7ceed0cd9db7eb7182481b6989f80cef31ee5
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/21228
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This patch defines Max PCIE Root Ports and fixes
bellow Coverity scan defect,
*** CID 1380036: Control flow issues (NO_EFFECT)
/src/soc/intel/cannonlake/romstage/romstage.c: 80 in soc_memory_init_params()
79
>>> CID 1380036: Control flow issues (NO_EFFECT)
>>> "i" is converted to an unsigned type because it's compared to an unsigned constant.
80 for (i = 0; i < ARRAY_SIZE(config->PcieRpEnable); i++) {
81 if (config->PcieRpEnable[i])
82 mask |= (1 << i);
Change-Id: Id45ff6e96043ed71117018a4e73d08920ae9667e
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/21272
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Fix dump_pci_device() broken by commit 65b72ab5 (Drop print_ implementation
from non-romcc boards) in 2015 (!) where only one in 16 bytes were being
dumped.
Also remove the #if made redundant by commit aef8542 (Compile debug.c
only if CONFIG_DEBUG_RAM_SETUP) as this whole file is only compiled in
that case.
Also clean up headers that were included twice.
Change-Id: I60e272b29417039feb15540e49d7300f86e5ed21
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/21203
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Some of these will move to EARLY_CBMEM_INIT.
Change-Id: Ia969e30ad7097860180bd047eaf81859a42a747c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21311
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Keith Hui <buurin@gmail.com>
Cannonlake LPSS UART port can be working on both 32 bit and 8 bit mode.
To maintian compatibilty with previous generation of SOC, select 32 bit
mode as default.
Change-Id: Iaef8bceabc1b12e054ab4a364f98b568a9efcd85
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/21296
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
NOTE: Some code was currently left behind that may be
required for certain type of board reboots. A followup
patch will address this.
Change-Id: I8fb89fb82c3a3608bb84b29319eb793605538996
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/19176
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
NOTE: Some code was currently left behind that may be
required for certain type of board reboots. A followup
patch will address this.
Change-Id: I3c1258b4e4dcf6fd04f57f5ab59cb1572a7d1fa3
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/19177
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch ensures that entire system memory calculation is done
based on host bridge registers.
BRANCH=none
BUG=b:63974384
TEST=Build and boot cannonlake RVP successfully with below configurations
1. Booting to OS with no UPD change
2. Enable ProbelessTrace UPD and boot to OS.
3. Enable PRMRR with size 1MB and boot to OS.
4. Enable PRMRR with size 32MB and boot to OS.
5. Enable PRMRR with size 2MB and unable to boot to OS due to
unsupported PRMRR size.
6. Enable C6 DRAM with PRMRR size 0MB and boot to OS.
Change-Id: I0a430a24f52cdf6e2517a49910b77ab08a199ca2
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/21235
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch uses smm common library function to get tseg base
address and size. Hence removing definitions of smm_region()
from soc directory.
BRANCH=none
BUG=b:63974384
TEST=Build and boot reef successfully.
Change-Id: I091ca90cf576c0da35cf3fe010f8c22a18ef82d9
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/21291
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch uses system agent common library to
know tseg region start and size. Unable to remove smm_region()
function from soc code as SMM common library
is not yet available for skylake use.
BRANCH=none
BUG=b:63974384
TEST=Build and boot eve successfully.
Change-Id: If98b65805753db2c30d6fea29e401a17cef39799
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/21290
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Do not assert GPIO1_B3 otherwise BT would be disabled on Nefario.
Also, remove DVS support for CENTERLOGIC.
BUG=b:64702054, b:63537905
TEST=build coreboot
Change-Id: I350db2c080f2e41ae56413f5f895557978ef0ba8
Signed-off-by: Philip Chen <philipchen@google.com>
Reviewed-on: https://review.coreboot.org/21176
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Enabling XHCI is additionally controlled with Kconfig
option HUDSON_XHCI_ENABLE. Even when it is enabled,
it EHCI debug works on the USB port next to the
DVD drive door.
Change-Id: I83738da6015f58ecd0819c553d333a176365dc78
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21157
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Support code for Trinity and Richland is identical now.
I have also come across a unit with Trinity model CPU,
whose CPUID was not listed in f15rl while f15tn already
had support for f15rl.
Change-Id: Ia869429b75a9b308b4d4a84f16914ca629b1b1b5
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/20773
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
LLVM AS doesn't support as much GNU junk extensions, data16/32
is almost never needed in truth if we just use the correct op
suffix. So do that here, fixes clang/llvm builds with the
integrated-as toggled on.
Change-Id: I6095d03d0289b418a49a10f135de5eb0e117cae0
Also-by: Damien Zammit <damien@zamaudio.com>
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Reviewed-on: https://review.coreboot.org/21218
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch to avoid build bot hang issue due to no
active default value for UART_FOR_CONSOLE kconfig
option.
Change-Id: I70ca5dc6c4bde6a119ad59d8c58955c96c042198
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/21287
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
BUG=b:64987428
TEST=Verified that touchscreen works on boot-up and after
suspend/resume. No power leakage via stop gpio in suspended state.
Change-Id: Ia260eb444081dbe1646c90e82c2725661e7306bc
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/21250
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
There is at least one I2C device (being used by Soraka) that has 3
controls -- enable, reset and stop. If the stop gpio is not put into
the right state when turning off the device in suspend mode, then it
causes leakage. Thus, we need control in power resource to be able to
stop the device when entering suspend state.
BUG=b:64987428
TEST=Verified on soraka that touchscreen stop is correctly configured
on suspend.
Change-Id: Iae5ec7eb3972c5c7f80956d60d0d3c321bbefb0f
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/21249
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
We no longer use this touchscreen device, so get rid of it.
BUG=b:64987428
Change-Id: I67af787d231317a80998fb483eed5674de19aeb4
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/21248
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Update cyan's SPD-related functions to more closely mirror
those of other Braswell boards, in order to simplify the upcoming
baseboard/variant setup for Braswell ChromeOS boards.
TEST: boot google/cyan, observe SPD correctly identified in
cbmem log, RAM-related data correct in SMBIOS tables.
Change-Id: Iafe99ec0795764f645e0a91f5b321be5b4c6fd88
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/21197
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Replaces the ics/954309 driver with a more generic version to
accommodate clockgens with a different amount of registers.
It also features a mask to only touch certain bits of the clockgen.
TODO: set appropriate mask for X60/T60 since the datasheets for their
clockgens can be found.
Change-Id: Ie43c4de7891a39f2f443e78213ecd688134e68d7
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/20042
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
This patch to add helper function to get SMM region start
and size based on systemagent common library.
BRANCH=none
BUG=b:63974384
TEST=Build and boot eve successfully.
Change-Id: If10af4a3f6a5bd22db5a03bcd3033a01b1cce0b4
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/21268
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch to add helper function to get tseg memory base and
size for HW based memory layout design.
BRANCH=none
BUG=b:63974384
TEST=Build and boot eve successfully.
Change-Id: I4c8b79f047e3dc6b2deb17fdb745f004004526b6
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/21267
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Add a 16ms delay to DMIC init by the kernel driver in order to
prevent an audible 'pop' noise when starting to record.
BUG=b:63413023
TEST=manual testing to ensure this device property is present in SSDT:
Name (_DSD, Package () {
ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301")
Package () {
Package () {
"realtek,dmic-init-delay",
0x10
}
}
})
Change-Id: If9160ce6992153ba49719029de336595bbf4ae72
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/21271
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Add support for providing additional free form device properties via
devicetree in order to make this driver suitable for kernel drivers
that need additional board-specific device properties.
This currently allows adding up to 10 additional properties to a device.
BUG=b:63413023
TEST=manual testing to ensure that newly added properties are in SSDT
Change-Id: I2b8ceb208f4aba01053746547def6d07c8f8f3a2
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/21270
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Provide a new function that will allow adding arbitrary properties
to devicetree entries without needing a custom driver for the device.
This will allow the 'generic i2c' driver to support kernel drivers
that need additional device properties exposed and have those board
specific properties set with values from devicetree.
BUG=b:63413023
TEST=not used yet, compiles cleanly
Change-Id: Id272256639a8525406635e168a3db5ab1ba4df6b
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/21269
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
On platforms with a PCH, some registers within host bridge should be
locked down on each normal boot path (done by either coreboot or
payload) and S3 resume (always done by coreboot).
A function to perform such locking is implemented in src/northbridge/
intel/*/finalize.c, and is designed as the handler of an #SMI triggered
with outb(APM_CNT_FINALIZE, APM_CNT), but currently this #SMI is only
triggered during s3 resume, and not on normal boot path. This problem
has beed discussed in
https://mail.coreboot.org/pipermail/coreboot/2017-August/084924.html .
This time, an option "INTEL_CHIPSET_LOCKDOWN" within src/southbridge/
intel/common/Kconfig is added to control the actual locking, which
depends on several compatibility flags, including
"HAVE_INTEL_CHIPSET_LOCKDOWN".
In this commit, "ibexpeak", "bd82x6x", "fsp_bd82x6x", and "lynxpoint"
have the flag "HAVE_INTEL_CHIPSET_LOCKDOWN" selected.
The change is only well tested on Sandy Bridge, my Lenovo x230.
Change-Id: I43d4142291c8737b29738c41e8c484328b297b55
Signed-off-by: Bill XIE <persmule@gmail.com>
Reviewed-on: https://review.coreboot.org/21129
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
The EC side of the feature bits in ACPI EC space isn't stable yet, and
we're now going for matching them up with the EC host command of the
same purpose.
Change-Id: I9c1f0e5390e840ea0c32315a3da8eea6f3e12f54
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/21193
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
We never had a board in the tree that implements this.
If you are interested in implementing such board, note
that also f12 and f14 had copies of the same refcode.
As part of the sourcetree cleanup it was not studied
which was the most up-to-date one for AM3r2.
Change-Id: Ic7dd065c0df08c22af6f3a2dcfc7ff47d6283a46
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21255
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
The only subtree we build is /ON.
Change-Id: I8cb11211a2a5ab7d8ae6296b601ee09146a9c9f8
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21254
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The only subtree we build is /LN.
Change-Id: I035932a4be41fa0451a3f3c7be33442afeeb5571
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21253
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
These files were never built in our tree.
Furthermore, AMD_INIT_RECOVERY was already deprecated
in AGESA spec rev 2.20 from Dec 2013.
Change-Id: Ifcaf466ca0767bf7cfa41d6ac58f1956d71c7067
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21252
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
"pcie_port_coalesce" will cause pcie being remapped under certain
conditions, but flags within "pcie_hotplug_map" should be updated
along with ports.
Test on my lenovo t430s.
Change-Id: I28c4eaf82fb52fe793dfa2f824f14686b80951ad
Signed-off-by: Bill XIE <persmule@gmail.com>
Reviewed-on: https://review.coreboot.org/21178
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This is a bug introduced by this commit:
stoneyridge: Fix CPU ASL \_PR table [commit I870f81]
The following error is found in dmesg
ACPI Error: [\_PR_.P000] Namespace lookup failure, AE_NOT_FOUND...
ACPI Exception: AE_NOT_FOUND, During name lookup/catalog...
ACPI Exception: AE_NOT_FOUND, (SSDT:AGESA ) while loading table...
ACPI Error: 1 table load failures, 3 successful...
...
acpi-cpufreq: overriding BIOS provided _PSD data
And, "ls -la /sys/devices/system/cpu/cpufreq/" doesn't work
The cause is that the Pstate SSDT table generated by AGESA expects CPU
variables \_PR.Pxxx, not \_PR.CPxx as generated by coreboot.
Use Kconfig to set the required string.
BRANCH=none
BUG=b:64885241
TEST= Check dmeg and ls -la /sys/devices/system/cpu/cpufreq/
Change-Id: I4929f9a1c39705c6df9d965c8d030f4d1f0b5e5f
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/21165
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Add a Kconfig option to change the \PR.CPxx name string. This
provides some flexibility when working with table not generated
by coreboot.
Change-Id: Ibc0c56783c6da80501e2177de96a414b592cb74f
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/21210
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Current coreboot does not create ACPI device for OS to recognize Raydium
touchscreen.
List the touch screen in the devicetree so that the correct ACPI device
are created.
BUG=b:64705535
BRANCH=master
TEST=emerge-coral coreboot
Change-Id: Ifdea897ef66dd10f29a8a0e72f9406d316fbe8c7
Signed-off-by: Pan Sheng-Liang <Sheng-Liang.Pan@quantatw.com>
Reviewed-on: https://review.coreboot.org/21233
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The guards in the header files were inconsistent. Some had no leading or
trailing underscores, some had one, some had both leading and trailing.
Change all to double leading & trailing underscores.
Change all comments to have a space before them instead of tabs
BUG=b:62235990
Test=Build Kahlee
Change-Id: I4466df529ab201c922096a31d7438381778b582f
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/21073
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
What is present is APIC and legacy interrupt routing and the soft-off sleep
state. Other sleep states are missing, so are the SuperIO devices.
Boots Linux with and without "noapic" and a Windows XP (installed with
factory BIOS, the installer reportedly requires legacy keyboard).
Change-Id: Iee3ede8683d1ea51317228d4f782af27043cc945
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-on: https://review.coreboot.org/18901
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Initialize IRQ routing for legacy non-PNP OSes the same as the factory
firmware would do.
Change-Id: I0c7a7d584a2c47471456ab54ef6da815a2dc4e7c
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-on: https://review.coreboot.org/18900
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
G170 is a board manufactured by WinNET, used in thin clients including
HP Neoware CA19 and IGEL 2110.
Copied from mainboard/bcom/winnetp680 which seems to be a similar
board with an extra PCI slot.
The p680 should probably be moved to winnet/ too, since the board is an
OEM WinNET board, with BCom being just a machine that happens to it.
Change-Id: I90b89ee634d90cfba2e56cca5b76cfd2bd7a8d0b
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-on: https://review.coreboot.org/18898
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Includes objects for interrupt links, the LPC bridge and interrupt
routing tables for the internal devices for both APIC and legacy
modes.
The default routing tables only includes peripherals internal to the
VT8237R, if a mainboard has PCI slots (mine does not have), it needs to
supply its own routing table.
Change-Id: I3a0cdafc19159fe6c38e4dde08ad0bf2bd0dd6b8
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-on: https://review.coreboot.org/18897
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Increase the default setting to add more CAR space for the early
console. This avoids truncation of the log.
BUG=b:64980233
Change-Id: Ia11d1c6c186a7025510c240206743ebe8d741461
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/21186
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Remove obsolete code. The same settings are always done in southbridge.
Change-Id: Ic893ddbace73ae8b122c4fb675febc7d1e0b5da9
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/21225
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Never selected in our tree. The vendorcode source
for fam15 also includes fam10 support if required.
Change-Id: Ifff328ecdd8afa988f844b6fd631818b51bd5b5b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21185
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Vendorcode for f15 also has f10 support, so
AMD_AGESA_FAMILY_10 was never selected.
Change-Id: I9a026c36ace88f1110a52d7e24d3e6ab36508932
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21184
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
We never had a board in the tree that implements this.
Change-Id: Idce32a20c24e31eb52f8509d4a7cccfc24cf17cf
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21180
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
These fam10 sources under fam12 and fam14 were never built.
Change-Id: Iff0964aba0a061b43144427388c07aea57d6d566
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21179
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This patch ensures skylake device using FSP1.1 can use HW based
DRAM top calculation which was broken due to skylake fsp1.1 not
honoring any UPD to know PRMMR size and default reserving 1MB for PRMRR size.
This WA is not needed for FSP2.0 implementation due to
PrmrrSize UPD is available and considering into hw based dram top
calculation.
BRANCH=none
BUG=b:63974384
TEST=Build and boot lars which is using skylake 1.1 fsp.
Change-Id: Iade0d2cb2a290fc4c9f0e6b1eaadc8afff2fa581
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/21224
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tune I2C params for I2C buses 0, 1, 2, 4 and 5 to ensure that the
frequency does not exceed 400KHz.
BUG=b:35948024
TEST=Verified for 25 iterations that the frequency on each bus ranges
<= 400KHz.
I2C0: 375 - 400
I2C1: 377 - 400
I2C2: 377 - 400
I2C4: 375 - 397
I2C5: 375 - 397
Change-Id: Ie30e1a12b66c4660b648a585c4dfd66faf004129
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/21208
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add critical and passive threshold to be advertised in thermal zone 0.
Change-Id: Ic75a80994b27ac19651ed52b7fc3c00c65cd9c01
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/21160
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Add support for board specific critical and passive
limits using GNVS table. Use default values if no
board specific limit exists.
* Add ACPI methods _TZP, _TSP and _PSV.
* Update ACPI method _CRT to use board specific if available.
Tested on Lenovo T500.
Change-Id: If438a909f4415f50cd7a764fb5fba7ec29599606
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/21159
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Rename register to match recent intel models.
Required for Lenovo H8 to operate on all generations.
Change-Id: I48a869adb1da2e33156968c4b7597edf99902c1a
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/21158
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This patch to ensure that coreboot is able to store memory
training data into SPI and perform platform lockdown after
PCI enumeration is done before handing over control to
NotifyPhase() - Post PCI enumeration.
Modified coreboot bootstate execution order below:
BS_DEV_ENUMERATE - BS_ON_EXIT - Store Memory training data into SPI
BS_DEV_RESOURCES - BS_ON_EXIT - Platform Lock Down after PCI enumeration
BS_DEV_ENABLE - BS_ON_ENTRY - NotifyPhase() post PCI enumeration
TEST=Please find test case and results for Chrome Devices as Apollolake- Reef,
Kabylake-Eve and Poppy and Non Chrome Devices with Yocto OS.
1.
Without patches
Cold Boot
MRC: no data in 'RW_MRC_CACHE'
...
MRC: Checking cached data update for 'RW_MRC_CACHE'.
SF: Detected FAST_SPI Hardware Sequencer with sector size 0x1000, total 0x1000000
MRC: no data in 'RW_MRC_CACHE'
MRC: cache data 'RW_MRC_CACHE' needs update.
MRC: NOT enabling PRR for 'UNIFIED_MRC_CACHE'.
Warm Reboot from Chrome CMD Line: $ reboot
MRC cache found, size 18c8 bootmode:2
...
MRC: Checking cached data update for 'RW_MRC_CACHE'.
SF: Detected FAST_SPI Hardware Sequencer with sector size 0x1000, total 0x1000000
MRC: NOT enabling PRR for 'UNIFIED_MRC_CACHE'.
Suspend Stress from Chrome CMD Line: $ echo mem > /sys/power/state
MRC cache found, size 18c8 bootmode:17
...
MRC: Checking cached data update for 'RW_MRC_CACHE'.
SF: Detected FAST_SPI Hardware Sequencer with sector size 0x1000, total 0x1000000
MRC: NOT enabling PRR for 'UNIFIED_MRC_CACHE'.
2.
With patches
Cold Boot
MRC: no data in 'RW_MRC_CACHE'
...
MRC: Checking cached data update for 'RW_MRC_CACHE'.
SF: Detected FAST_SPI Hardware Sequencer with sector size 0x1000, total 0x1000000
MRC: no data in 'RW_MRC_CACHE'
MRC: cache data 'RW_MRC_CACHE' needs update.
MRC: NOT enabling PRR for 'UNIFIED_MRC_CACHE'.
Warm Reboot from Yocto CMD Line: $ reboot
MRC cache found, size 18c8 bootmode:2
...
MRC: Checking cached data update for 'RW_MRC_CACHE'.
SF: Detected FAST_SPI Hardware Sequencer with sector size 0x1000, total 0x1000000
MRC: NOT enabling PRR for 'UNIFIED_MRC_CACHE'.
Suspend Stress from Chrome CMD Line: $ echo mem > /sys/power/state
MRC cache found, size 18c8 bootmode:17
...
MRC: Checking cached data update for 'RW_MRC_CACHE'.
SF: Detected FAST_SPI Hardware Sequencer with sector size 0x1000, total 0x1000000
MRC: NOT enabling PRR for 'UNIFIED_MRC_CACHE'.
Tested the patches more thoroughly, from the S5->S0, S3->S0 bootlog there
is no noticeable difference.
On a reboot, suspend resume from Chrome console, the mrc cache is found,
and utilized.
Change-Id: I4cb4eac5256c1ce98f51adad0be6e69f7d05d8e1
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/21084
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch to ensures that coreboot is performing SPI
registers lockdown after PCI enumeration is done.
This requirements are intended to support platform security
guideline where all required chipset registers are expected
to be in lock down stage before launching any 3rd party
code as in option rom etc.
coreboot has to change its execution order to meet those
requirements. Hence SPI lock down programming has been moved
right after pci resource allocation is donei, so that
SPI registers can be lock down before calling post pci
enumeration FSP NotifyPhase() API which is targeted to
be done in BS_DEV_ENABLE-BS_ON_ENTRY.
TEST=Ensure SPIBAR+HSFSTS(0x04) register FLOCKDN bit and WRSDIS
bit is set. Also, Bits 8-12 of SPIBAR+DLOCK(0x0C) register is set.
Change-Id: I8f5a952656e51d3bf365917b90d3056b46f899c5
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/21064
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Now that there is a handy macro utilize it.
Change-Id: I560bc7a591075235229952cdea63d4e667f323ee
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/21204
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This patch to ensures that coreboot is performing DMI
registers lockdown after PCI enumeration is done.
This requirements are intended to support platform security
guideline where all required chipset registers are expected
to be in lock down stage before launching any 3rd party
code as in option rom etc.
coreboot has to change its execution order to meet those
requirements. Hence BIOS Interface lock down through Sideband
access has been moved right after pci resource allocation is done,
so that BILD lock down is getting executed along with LPC and SPI
BIOS interface lockdown settings before calling post pci
enumeration FSP NotifyPhase() API which is targeted to
be done in BS_DEV_ENABLE-BS_ON_ENTRY.
TEST=Ensure DMI register offset 0x274c bit 0 is set.
Change-Id: Ie66701d5bd8c8f389e23fb30c8595dd83cf6b1ae
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/21030
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The LED polarity was set incorrectly, fix using values derived
from original Chromium sources:
branch firmware-mccloud-5827.B, ToT
src/mainboard/google/mccloud/smihandler.c
src/mainboard/google/mccloud/romstage.c
TEST: boot google/mccloud, observe power LED on normally,
blinking in S3/S4, and off in S5.
Change-Id: Ia1f63eebbccb48fcf8543188db390b23045d843e
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/21102
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Commit 0562783182 applied
this change to other Google boards, but cyan was left out.
Bring cyan in line with other Google boards.
Change-Id: Id86bea538a7b82367ea6ddbd3fe3efb1b1c0078d
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/21124
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Cleaning up code to remove support for pre-EVT rev of cyan board.
Analogous to what was done for intel/strago in commit 103f00d.
Change-Id: I29b32da8064e0743cc9c5df02ce7d3441459ee8f
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/21123
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Cherry-pick from Chromium commit a162348.
Remove the hard coded IRQ number for the keyboard interrupt.
IRQ number can change based upon the gpio bank index ordering.
Hence pass the gpio bank and index number so that kernel calculates
the IRQ number.
Original-Change-Id: Icfe5c3995007164bf617575b541758c18ee63a1d
Original-Signed-off-by: Jagadish Krishnamoorthy <jagadish.krishnamoorthy@intel.com>
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Change-Id: I81ff19e3060c533ee76023c7651f741294e9db30
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/21177
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Adapted from Chromium commit dc59188.
Disable L1 sub state to prevent WiFi randomly disappear condition.
Original-Change-Id: I8975bb4bbbc2fc89b91b06ae02716367890c672d
Original-Signed-off-by: T.H. Lin <T.H_Lin@quantatw.com>
Original-Reviewed-by: Rajat Jain <rajatja@chromium.org>
Original-Reviewed-by: Vincent Wang <vwang@chromium.org>
Oriignal-Tested-by: TH Lin <t.h_lin@quanta.corp-partner.google.com>
Change-Id: I51a1bcca6431e6bc28baf9b09433cec13db925c3
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/21174
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Cherry-pick from Chromium commit f92d7be.
This BAR is used in _PS0 and _PS3 methods and is used by kernel driver to put
SD controller in D3
Original-Change-Id: Iae4722cb222f61e96948265f57d6b522065853d9
Original-Signed-off-by: Hannah Williams <hannah.williams@intel.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Reviewed-by: Duncan Laurie <dlaurie@google.com>
Original-Tested-by: Aseda Aboagye <aaboagye@chromium.org>
Change-Id: I59973226d57fe1dc3da21b2cec1c7b9a713829ab
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/21172
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Cherry-pick from Chromium commit 1138727.
Elan touchscreen driver expects the first gpio resource in asl
to be the reset line.
The driver considers the gpio based irq line as reset gpio resource
and changes the direction to output.
This will cause irq registration to fail.
Solution is to pass Interrupt resource for touchscreen irq
instead of GpioInt.
Original-Change-Id: Ia72d4ad80117f3c0014098113c9027416026e65e
Original-Signed-off-by: Jagadish Krishnamoorthy <jagadish.krishnamoorthy@intel.com>
Original-Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Change-Id: I1c4b029851e321feeedf713186976fbec42dd82e
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/21122
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Cherry-pick from Chromium commit e49deb1.
Configuring UPD PcdCaMirrorEn. This is a board specific parameter.
CA mirror is the Command Address mirroring option that is board
specific.
Original-Change-Id: I05174e18d650332d838e5036c713e91c4840ee75
Original-Signed-off-by: Divya Sasidharan <divya.s.sasidharan@intel.com>
Original-Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Original-Tested-by: Hannah Williams <hannah.williams@intel.com>
Change-Id: Ibd0c811d41cb592634f7785edb83ad2f423546c5
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/21169
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Needed for to-be-added Google Braswell boards which make use
of common GPIO library function to determine installed RAM type.
Change-Id: Ie9b0c6513f10b252bf0a5014bd038d24879421be
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/21125
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch to ensures that coreboot is performing PMC
registers lockdown after PCI enumeration is done.
This requirements are intended to support platform security
guideline where all required chipset registers are expected
to be in lock down stage before launching any 3rd party
code as in option rom etc.
coreboot has to change its execution order to meet those
requirements. Hence PMC register lock down has been moved
right after pci resource allocation is done, so that
PMC registers can be lock down before calling post pci
enumeration FSP NotifyPhase() API which is targeted to
be done in BS_DEV_ENABLE-BS_ON_ENTRY.
TEST=Ensure PMC MMIO register 0xC4 bit 31 is set.
Change-Id: Ibd86a38fa78752ce007da63a9ccdd991ca21ab92
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/21029
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch to ensures that coreboot is performing LPC
registers lockdown after PCI enumeration is done.
This requirements are intended to support platform security
guideline where all required chipset registers are expected
to be in lock down stage before launching any 3rd party
code as in option rom etc.
coreboot has to change its execution order to meet those
requirements. Hence lpc register lock down has been moved
right after pci resource allocation is done, so that
lpc registers can be lock down before calling post pci
enumeration FSP NotifyPhase() API which is targeted to
be done in BS_DEV_ENABLE-BS_ON_ENTRY.
TEST=Ensure LPC register 0xDC bit 1 and 7 is set.
Change-Id: I705a3a3c6ddc72ae7895419442d67b82f541edee
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/21000
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch ensures that MRC cache data is already written
into SPI chip before SPI protected regions are getting locked
during BS_DEV_RESOURCES-BS_ON_EXIT.
This requirements are intended to support platform security
guideline where all required chipset registers are expected
to be in lock down stage before launching any 3rd party
code as in option rom etc.
coreboot has to change its execution order to meet those
requirements. Hence storing mrc cache data into SPI has
been moved right after pci enumeration is done, so that
SPI registers can be lock down before calling post pci
enumeration FSP NotifyPhase() API which is targeted to
be done in BS_DEV_ENABLE-BS_ON_ENTRY.
TEST=Ensure MRC training data is stored into SPI chip and power_
Resume autotest is passing.
Change-Id: I8ee26b5cc70433438cf4e45e707b8a54f89cf9b0
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/21028
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch to provide new config options to perform LPC and SPI
lock down either by FSP or coreboot.
Remove EISS bit programming as well.
TEST=Build and boot Eve and Poppy.
Change-Id: If174915b4d0c581f36b54b2b8cd970a93c6454bc
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/21068
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
In order to pass type C USB2 eye diagram for sku Santa,
USB2 port#1 PHY register needs to be overridden.
port#1:
PERPORTPETXISET = 7
PERPORTTXISET = 2
BUG=b:64880573
BRANCH=master
TEST=emerge-coral coreboot chromeos-bootimage
Change-Id: I07c0b7b0f08263a348befb7d6fd8d01028314470
Signed-off-by: Tim Chen <Tim-Chen@quantatw.com>
Reviewed-on: https://review.coreboot.org/21199
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Move the fchec.h files, which do not seem mainboard specific, out of
the mainboard directories into the southbridge/soc directories.
Change-Id: Idd271c6ab618aa4badf81c702212e7de35317021
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/20677
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
This is not specific to a board but the binary IMC firmware
used on the platform. Also remove unused IMSP and IMWK methods.
Change-Id: I80026bca55f5ba236c080bcd882fc374559942e6
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21191
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
It was not intentional to change oem_fan_control() to non-static
with commit
23e5ba9 binarypi mainboards: Clean up IS_ENABLED fan control
Every platform except bettong had its own static version of
oem_fan_control, so remove the definition of oem_fan_control from imc.h,
and move it out of imc.c into bettong's BiosCallOuts.c.
Change-Id: Ie95ac1fd3a57259bb35796903aa8753ef0e70d70
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/21189
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Remove all checks for #if IS_ENABLED(CONFIG_HUDSON_IMC_FWM) around
the imc.h includes. Convert from #if to if() for all fan control
setup code. Where necessary, make functions non-static to match the
prototypes in imc.h.
Change-Id: If88af42d00227285931829441909a982fc292b2b
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/21058
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Remove all checks for #if IS_ENABLED(CONFIG_HUDSON_IMC_FWM) around
the imc.h includes. Convert all #if to if() for fan control setup.
Change-Id: I04a9fbbf6f64f45e1a0b544267bfe840ce7fa1d9
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/21059
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Don't include src/include/cpu/amd/car.h in Via motherboards.
Change-Id: I9d2b3cfb619cf831c7a677992ca03d5f42e5ffd1
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/19404
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
This patch ensures that entire system memory calculation is done
based on host bridge registers.
BRANCH=none
BUG=b:63974384
TEST=Build and boot eve and poppy successfully with below configurations
1. Booting to OS with no UPD change
2. Enable ProbelessTrace UPD and boot to OS.
3. Enable PRMRR with size 1MB and boot to OS.
4. Enable PRMRR with size 32MB and boot to OS.
5. Enable PRMRR with size 2MB and unable to boot to OS due to
unsupported PRMRR size.
Change-Id: I9966cc4f2caa70b9880056193d5a5631493c3f3d
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/21150
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This change provides interface to override dev tree settings per
board due to many projects share same devicetree.cb.
BUG=b:64880573
TEST=Verify that dev tree settings can be overridden in mainboard
on coral
Change-Id: I349b1678d9e66022b586b6c7f344b831ed631c74
Signed-off-by: Kane Chen <kane.chen@intel.com>
Reviewed-on: https://review.coreboot.org/21142
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested on T430s with an external screen connected to every one of the
DP ports (miniDP on mainboard, two DP ports on dock), the GRUB payload
can display on both the external screen and the internal LVDS screen.
This is a copy-paste of I8f270d55 "mb/lenovo/x230: Enable libgfxinit".
Change-Id: Ifb1471ecb18927c30c61c64011cbb0e20a465558
Signed-off-by: Bill XIE <persmule@gmail.com>
Reviewed-on: https://review.coreboot.org/21070
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Sync file with southbridge/amd/common/sleepstates.asl.
SSFG was meant to be used as a mask to enable sleepstates
_S1 thru _S4. However as a logical instead of bitwise 'and'
operation was used, all the states were enabled if only
one was marked available.
Change-Id: I674953f1a5add74e16ddd84c252e8d21501ffefd
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21092
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Note that against the specs, these definitions repeat
the sleep type also in the reserved fields 3 and 4.
For consistency, don't fix it here now.
Entry for \_S3 is now masked off if HAVE_ACPI_RESUME=n.
Change-Id: Icdc4c81d07fe7a99d5b0f8fa23e9443f58a40ab9
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21143
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
SSFG was meant to be used as a mask to enable sleepstates
_S1 thru _S4. However as a logical instead of bitwise 'and'
operation was used, all the states were enabled if only
one was marked available.
Note that all boards incorrectly had SSFG == 0x0D that previously
enabled ACPI S3 sleep state even when it was not available.
Change-Id: Ia948becff079383cbf861468da9e8a3ebbf213cb
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21093
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
SSFG was meant to be used as a mask to enable sleep states
_S1 thru _S4. However as a logical instead of bitwise 'and'
operation was used, all the states were enabled if only
one was marked available.
State _S3 is now set conditionally if HAVE_ACPI_RESUME=y.
For pi/hudson this had been fixed already preprocessor.
Note that all boards had SSFG == 0x0D that previously
enabled ACPI S3 sleep state even when it was not available.
States _S1 and _S2 still appear enabled in ASL/AML
but may not actually work.
TEST: 'cat /sys/power/state' and notice choice 'mem' was
removed from the list of available sleep states.
Change-Id: I27d616871c1771f0c87d8fba23d4ce1569607765
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21091
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marc Jones <marc@marcjonesconsulting.com>
Return to empty stack before making the switch.
Change-Id: I6d6f633933fac5bc08d9542c371715f737fb42cf
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/20574
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: Raptor Engineering Automated Test Stand <noreply@raptorengineeringinc.com>
This enables adding the backlight driver to boards that may or may not
come with a keyboard backlight function.
It's the responsibility of the EC to report if that feature exists, but
that's not a big extra burden given that it already keeps track of
everything else related to the backlight.
BUG=b:64705535
BRANCH=none
CQ-DEPEND=CL:620595
TEST=configured KBLE manually and noticed the presence/absence of
/sys/devices/platform/GOOG0002:00/ on a Chrome OS Linux kernel,
corresponding to the value reported by the EC.
Change-Id: Idc36bfaa6e69581ba19b52d37af6956f63cfdb8f
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/21099
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The Sideband Acces locking code is skipped from FSP by setting an
FSP-S UPD called PchSbAccessUnlock. This locking is being done in
coreboot during finalize.c.
This is done because coreboot was failing to disable HECI1 device
using Sideband interface during finalize.c if FSP already locks
the Sideband access mechanism before that.
So, as a solution, coreboot passes an UPD to skip the locking
in FSP, and in finalize.c, after disabling HECI, it removes the
Sideband access.
BUG=b:63877089
BRANCH=none
TEST=Build and boot poppy to check lspci not showing Intel ME
controller in the PCI device list.
Change-Id: I8dba4c97480200507969b0f2873337f97bd2ff6a
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/20956
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Kahlee has an ambient light sensor connected to the EC.
TEST=Can see the device in /sys/bus/iio
BUG=b:62030268
Change-Id: Id1138a0fc5270489a734bdf8b1f4ac02d358c0df
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-on: https://review.coreboot.org/21146
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch assigns the code of coral family, such that,
the 'mosys platform family' returns 'Google_Coral'.
BUG=b:64467244, b:64501879
BRANCH=none
TEST=Examine 'mosys platform family' w/ new firmware.
Change-Id: I1d8f8ca2166a1d80855608cf5b64b0cc7bf3dc93
Signed-off-by: Harry Pan <harry.pan@intel.com>
Reviewed-on: https://review.coreboot.org/21136
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
This update changes Cannonlake to use the new common PMC code. This
will help to reduce code duplication and streamline code bring up.
Change-Id: Ia69fee8985e1c39b0e4b104c51439bca1a5493ac
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/21062
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Configure core PRMRR first on all the cores and then follow
the SGX init sequence. Second microcode load would run the
MCHECK. To pass MCHECK, PRMRR on all cores needs to be
configured first. Hence, PRMRR configuration would be called
from soc_core_init while MP init for each core and then from
soc_init_cpus, BSP would call sgx_configure for each core
(including for itself). This code flow satisfies the MCHECK
passing pre-conditions; and apparently this patch fixes the
behavior of calling configure_sgx() “again” for BSP. (So
removed the TODO comment also).
Change-Id: I88f330eb9757cdc3dbfc7609729c6ceb7d58a0e1
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/21007
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
To correct the SGX init sequence; PRMRR on all cores first
needs to be set, then follow the SGX init sequence. This
patch would refactor the common SGX code (and add needed
checks in the init sequence) so that SOC specific code can
call SGX init in correct order.
Change-Id: Ic2fb00edbf6e98de17c12145c6f38eacd99399ad
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/21006
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Remove passing microcode patch pointer as param while calling
- soc_core_init()
- soc_init_cpus()
Also change callbacks in apollolake/geminilake and skylake/kabylake
common code to reflect the same function signature.
Change-Id: Ib03bb4a3063d243d97b132e0dc288ef3868a5a7b
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/21010
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Early serial for W83627[HF|EHG] superios are handled by
superio/winbond/common/early_serial.c. Remove code
thus deprecated.
Build tested on select affected mainboards.
Change-Id: Idad6e0281f7a272e184feff686ce1407825429c7
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/20988
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Six mainboards with Winbond superios directly configure
them in romstage.c. All use the common Winbond romstage
code. Change them to use the common config entry code to
allow for code refactoring such as [1]. Build tested.
[1] https://review.coreboot.org/20988
Change-Id: Icecd52ec622b9da86edb07c52893f4db001e5562
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/20989
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested:
- i5-3550 and DIMM configurations: 2+0+2+2, 0+2+2+2, 2+2+2+2, 4+2+4+2
- debug output from serial port, EHCI debug port not found
- Arch Linux (Linux 4.11.5) loaded from SeaBIOS, GRUB2, and Linux payload
- all PCI and PCI Express slots
Issues:
- sometimes the machine fails to boot, with serial debug output it can
be seen it stucks after SMM initialization, and more likely to fail
to boot when serial cable is attached
- no S3 resume (not tested in vendor firmware)
Change-Id: I94fbfcee06921538b32aa3c23efa642e7e405ef6
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/20227
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Add two additional LED IDs.
Add Kconfig menu entries to allow selecting the action
to execute on death.
Overwrite weak die_notify method to notify user on death.
Flash all LEDs and play beep code 10 depending on Kconfig
options.
Successfully tested on:
Tested on Lenovo T500.
Tested on Lenovo X200.
Tested on Lenovo T430, but only LEDs are flashing.
Change-Id: Id34d399f154952a48c1f4ccb0c41a238b2d7ccb8
Signed-off-by: Patrick Rudolph <siro@das-labor.org
Reviewed-on: https://review.coreboot.org/19695
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Current coreboot does not create ACPI device for OS to recognize Raydium
touchscreen.
List the touch screen in the devicetree so that the correct ACPI device
are created.
BUG=b:64821783
BRANCH=reef
TEST=emerge-snappy coreboot
Change-Id: I8852e38f01f82b80c2c9718b93baf5894dbd745b
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/21083
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Current coreboot does not create ACPI device for OS to recognize MELFAS
touchscreen.
List the touch screen in the devicetree so that the correct ACPI device
are created.
BUG=b:64779224
BRANCH=reef
TEST=emerge-snappy coreboot
Change-Id: If2bc910d641e0cf2b120ed883c5788542959f568
Signed-off-by: Kevin Chiu <Kevin.Chiu@quantatw.com>
Reviewed-on: https://review.coreboot.org/21067
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Get microcode patch pointer from intel_mp_current_microcode() api
of mp_init and change sgx_configure function signature to drop
microcode_patch param.
Change-Id: I9196c30ec7ea52d7184a96b33835def197e2c799
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/21009
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Cannonlake SOC has two possible ways to make serial
console functional.
1. Legacy IO based access using Port 0x3F8.
2. LPSS UART PCI based access.
This patch to provide option to select index for LPSS
UART port: 0 = LPSS UART0, 1 = LPSS UART1, 2 = LPSS UART2
PCI based LPSS UART2 is by default enabled for Chrome Design.
Change-Id: I7afa5ab2c5eb06e6df8eeb1cb1cd0de00d2b2a28
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/20998
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Skylake/Kabylake SOC has two possible ways to make serial
console functional.
1. Legacy IO based access using Port 0x3F8.
2. LPSS UART PCI based access.
This patch to provide option to select index for LPSS
UART port: 0 = LPSS UART0, 1 = LPSS UART1, 2 = LPSS UART2
PCI based LPSS UART2 is by default enabled for Chrome Design.
Change-Id: I9647820fe59b5d1a1001a611b9ae3580946da0ae
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/20996
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Remove the duplicate MISCCFG_GPE0_DW* macros that are already present
in the common gpio code.
Change-Id: Iad75e5f7e276b37b5861f0c9a3bb0bb2824a638c
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: https://review.coreboot.org/21078
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Add mp_current_microcode() function to get the microcode patch pointer.
Use this function to avoid reading the microcode patch from the boot
media. init_cpus() would initialize microcode_patch global variable to
point to microcode patch in boot media and this function can be used
to access the pointer.
Change-Id: Ia71395f4e5b2b4fcd4e4660b66e8beb99eda65b8
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/21061
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
FSP might have done some settings for us there. Use pci_update_config32()
since the register is documented to be 32 bits wide.
Change-Id: I995e8a731a6958f10600174d031bb94f5a0a66db
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/21072
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Relevant changes (commit 2e8761e):
* Add an option to truncate the ME image file
* Add full support for Skylake (ME 11) and following, including
modules removal, truncation informations and partition
relocation
* Add two options to generate a shrinked ME image file and the
corresponding descriptor with a modified flash layout
* Update README.md
* Bug fixes
Also add a link to the usage guide in the Kconfig help.
Change-Id: I690c5d558139f64f38babf3c0988b53834ba8b37
Signed-off-by: Nicola Corna <nicola@corna.info>
Reviewed-on: https://review.coreboot.org/20915
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Clear LAST_BYTE flag at beginning of block commands.
For reads, slave device determines in the message format how
many bytes it has to transfer out, host firmware only dictates
the maximum buffer length. Return SMBUS_ERROR if only
partial message was received.
For writes, return SMBUS_ERROR if length > 32.
For writes, fix off-by-one error reading memory one
byte past the buffer end.
Change-Id: If9e5d24255a0a03039b52d2863bc278d0eefc311
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/20879
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
A small typo in the dll setting code prevented this combination from
booting.
TESTED on ga-g41m-es2l with 800MHz FSB CPU and 667MHz ddr2
Change-Id: Ib013471773c20336ba0902b7f328bfb6ef970747
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/20981
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Moves receive enable calibration to a separate file to lighten
raminit.c a bit.
Receive enable calibration is quite similar to gm45 so it reuses some
of its function names.
The functional changes are:
* the minimum coarse is now reset for each channel;
* on the second fine search for DQS high, TAP overflow is handled by
increasing medium;
* start coarse at CAS + 1 instead of CAS - 1. Other Intel northbridges
do the same and the results are more in line with register dumps
from vendor bios.
These might improve stability.
TESTED on ga-g41m-es2l
Change-Id: I0c970455e609d3ce96a262cbf110336a2079da4d
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/18692
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
On this device libgfxinit successfully initializes textmode and
framebuffer mode on the device connected to the HDMI1 port.
VGA port is not tested, due to lack of VGA with valid EDID.
Every ports works on GNU/Linux with kernel version 4.9+80+deb9u1.
Due to limitations within the libgfxinit's current build system,
it needs "select NORTHBRIDGE_INTEL_IVYBRIDGE" to work, even it is
PCH instead of CPU for which libgfxinit should be configured here.
Change-Id: Ib1513fc57b79eebc5d047c2e24585731c44bc215
Signed-off-by: Bill XIE <persmule@gmail.com>
Reviewed-on: https://review.coreboot.org/21071
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Fail at build-time if one of the following happens:
Platform includes SMI handler setup function smm_init()
in the build when configuration has HAVE_SMI_HANDLER=n.
Platform does not implement smm_init_completion() when
HAVE_SMI_HANDLER=y.
Change-Id: I7d61c155d2b7c2d71987980db4c25d520452dabf
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/21097
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Instead of enabling power button SMI unconditionally, add a boot state
handler to enable power button SMI just before jumping to
payload. This ensures that:
1. We do not respond to power button SMI until we know that coreboot
is done.
2. On resume, there is no need to enable power button SMI. This avoids
any power button presses during resume path from triggering a
shutdown.
BUG=b:64811381
Change-Id: Icc52dc0103555602c23e09660bc38bb4bfddbc11
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/21082
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Do not use the global platform_i2c_transfer() function that can only be
implemented by a single driver. Instead, make a `struct device` aware
transfer() function the only interface function for I2C controller dri-
vers to implement.
To not force the slave device drivers to be implemented either above
generic I2C or specialized SMBus operations, we support SMBus control-
lers in the slave device interface too.
We start with four simple slave functions: i2c_readb(), i2c_writeb(),
i2c_readb_at() and i2c_writeb_at(). They are all compatible to respec-
tive SMBus functions. But we keep aliases because it would be weird to
force e.g. an I2C EEPROM driver to call smbus_read_byte().
Change-Id: I98386f91bf4799ba3df84ec8bc0f64edd4142818
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/20846
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Split `i2c.h` into three pieces to ease reuse of the generic defi-
nitions. No code is changed.
* `i2c.h` - keeps the generic definitions
* `i2c_simple.h` - holds the current, limited to one controller driver
per board, devicetree independent I2C interface
* `i2c_bus.h` - will become the devicetree compatible interface for
native I2C (e.g. non-SMBus) controllers
Change-Id: I382d45c70f9314588663e1284f264f877469c74d
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/20845
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The code is based on autoport. I'm using a machine with discrete GPU,
and gfx.* in devicetree.cb is from 2760p.
It can be debug with serial port on dock.
Tested:
- CPU and memory: i5-2540M, 4G+0
- Arch Linux (Linux 4.11.7, SeaBIOS payload, with ATOM BIOS extracted
from vendor UEFI firmware)
- USB ports
- SD card reader
- WLAN
- DP display
- S3
Change-Id: I9c42723ba240a2e9b46998c1a8a708aebc66c604
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/20501
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
The code is based on autoport. The EHCI debug port is the upper USB
port beside the battery.
Tested and working:
- CPU and memory: i7-3720QM, 4G+4G
- Linux Mint with Linux 4.4 (SeaBIOS payload)
- All USB ports
- ExpressCard
- WLAN
- AC and battery status
- S3
- Other devices detected: DVD drive, smartcard reader, fingerprint, bluetooth
Not tested:
- VGA and DP
- Ethernet and modem
- Dock
Change-Id: I9f3cd124fc676d49add59e9f0a07f70a6bb0fff0
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/20489
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
The code is based on the code generated by autoport.
The EHCI debug port is between the DP port and eSATA port.
The serial port on dock can also be used for debugging.
The model with discrete graphics is not tested.
Tested and work:
- memory: 0+4G, 4G+0, 4G+4G
- Linux (Arch Linux with kernel 4.10.6) boot from SeaBIOS payload
with native graphics init
- WLAN
- keyboard, trackpoint and touchpad
- USB
- serial port on dock
- fan control
- AC and battery status
(EC) blobs:
This laptop uses SMSC KBC1126 EC, and there are two blobs needed by it.
You can use the tools in util/kbc1126/ to extract them and insert them
to the coreboot image using the following configuration:
-> Chipset
-> Add firmware images for KBC1126 firmware
Change-Id: Icbc051e2272b8ea73627940db15a56901d737472
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/18985
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
The code is generated by autoport.
The flash chip is socketed beside the WLAN slot. The EHCI debug port
is on right side of the laptop beside the RJ11 connector.
Things that work:
- memory: 0+8G, 4G+8G
- Linux (Linux Mint 18.1 with Linux 4.4)
- native graphics init + SeaBIOS payload with SeaVGABIOS
- all 3 USB ports
- WLAN
- WWAN
- SD card reader
- expresscard
- S3 suspend and resume
- internal flashing after IFD is unlocked and coreboot is flashed
- keyboard, trackpoint and touchpad
- fan control
- AC and battery status
Issues:
- Wacom digitizer does not work (even after I add it in DSDT)
- GRUB payload will freeze (in all Elitebooks, including chainloading GRUB
from SeaBIOS)
Things that are not tested:
- smart card reader
- cable modem
(EC) blobs:
This laptop uses SMSC KBC1126-NU as EC. It needs two blobs in the
flash chip. You can use the tools in util/kbc1126 to extract them
from OEM firmware, and use the following configuration to insert
them to coreboot image:
-> Chipset
-> Add firmware images for KBC1126 firmware
Change-Id: I3ffdb9f9c71f6c9a84e896abc3c424c8dd4bed0e
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/18241
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This patch adds few helper functions in CPU common libraray code
which are mainly needed for ACPI module. The functions those are
moved to cpu common code is removed from common acpi files.
TEST= System boots properly and no regression observed.
Change-Id: Id34eb7e03069656238ca0cbdf6ce33f116e0e413
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/21051
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Chrome OS systems rely on the write status register to enable/disable
flash write protection and disabling this opcode breaks the ability
to enable or disable write protection with flashrom.
Add a configure option for this feature that will disable the opcode
for Write Status commands unless CONFIG_CHROMEOS is enabled.
Tested to ensure that a default build without CONFIG_CHROMEOS has this
option enabled while a build with CONFIG_CHROMEOS does not. Also
ensured that when this option is disabled (for Chrome OS) then flashrom
can be used with the --wp-enable and --wp-disable commands, depending
on the state of the external write protect pin.
Change-Id: Ia2ef3c3b1e10fba2c437e083f3537022f1fce84a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: https://review.coreboot.org/21021
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Move the FSP-specific call for tearing down cache-as-RAM out of
postcar.c and replace it with an empty weak function.
This patch omits checking if (IS_ENABLED(CONFIG_FSP_CAR)). The
temp_ram_exit.c file with the real fsp_temp_ram_exit() is only built
when CONFIG_FSP_CAR is true.
Change-Id: I9adbb1f2a7b2ff50d9f36d5a3640f63410c09479
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/20965
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Remove cpu.h from the cache-as-ram setup and teardown files that rely
on the FSP implementation. The struct device statement causes a
build failure and there appears to be nothing needed from cpu.h in
the two .S files.
TEST: Build Google Reef with FSP_CAR selected on Chipset menu and add
FSP binaries on the Generic Drivers menu.
Change-Id: I560b730c18d7ec73b65f2e195b790e7dcacfd6bb
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/21057
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The Giantec semiconductor GT24C16S and ON semiconductor CAT24C16
are the industrial standard electrically erasable programmable
read only memory (EEPROM's) and this patch adds ACPI objects
and power resources for NVMEM device.
Update DOVD method to set sensor IO LDO voltage and remove repetitive
code from OVFI, VCMP and NVMP power resources.
BUG=b:38326541
BRANCH=none
TEST=Build and boot soraka. Dump and verify that the generated DSDT table
has the required entries. Read the NVMEM content via sysfs interface.
Change-Id: If49ed33b7e1de1eabf317b31ceed8568dfca0aae
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/20495
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
We do not need or use the Management Engine MBP HOB so that
step can be skipped when FSP initializes the ME.
BUG=b:64479422
TEST=boot with FSP debug enabled binary and ensure that the
output indicates this step is being skipped:
Skipping MBP data due to SkipMbpHob set!
Change-Id: I5ea22ec4b8b47fa17b1cf2bf562337bfaad5ec0d
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/20951
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
BUG=b:64705535
BRANCH=master
TEST=emerge-coral coreboot chromeos-bootimage and verify the keyboard
backlight can be bright and alt+f6, alt+f7 function keys can be used.
Change-Id: I777247a6b58d3d50b72f12ca2fcab49a06ed5431
Signed-off-by: Pan Sheng-Liang <Sheng-Liang.Pan@quantatw.com>
Reviewed-on: https://review.coreboot.org/21027
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Need to perform a dummy read in order to activate LPSS UART's
16550 8-bit compatibility mode.
TEST=Able to get serial log in both 32 bit and 8 bit mode through
LPSS UART2 based on CONFIG_DRIVERS_UART_8250MEM_32 and
CONFIG_DRIVERS_UART_8250MEM selection.
Change-Id: Ief58fdcb8a91f9951a48c3bd7490b1c7fee17e48
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/20940
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Need to perform a dummy read in order to activate LPSS UART's
16550 8-bit compatibility mode.
TEST=Able to get serial log in both 32 bit and 8 bit mode through
LPSS UART2 based on CONFIG_DRIVERS_UART_8250MEM_32 and
CONFIG_DRIVERS_UART_8250MEM selection.
Change-Id: I5f23fef4522743efd49167afb04d56032e16e417
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/20939
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Like commit c91ab1cfc that targeted AGESA f14.
MemRestore() is still broken after this fix.
Change-Id: I7457de5e0c52819560e2bfd46b9e351b00d3d386
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/20900
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
Due to low-memory corruptions S3 support has now been
(at least temporarily) removed from AGESA platfroms.
Should we bring it back one day, CAR teardown on S3 path
will happen with an empty stack so ugly backup/recovery
of the stack will no longer be used.
If S3 feature is brought back, resume path code for FCH
will also see partial rewrite and agesawrapper.c file
will not be part of that.
Change-Id: Ib38c04d0e74f600e0b719940d5e2530f4c726cfd
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/20899
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
A decision has been made that boards with LATE_CBMEM_INIT
will be dropped from coreboot master starting with next
release scheduled for October 2017.
As existing implementation of CAR teardown in AGESA can only
do either EARLY_CBMEM_INIT or ACPI S3 support, choose the former.
ACPI S3 support may be brought back at a later date for
these platforms but that requires fair amount of work fixing
the MTRR issues causing low-memory corruptions.
Change-Id: I5d21cf6cbe02ded67566d37651c2062b436739a3
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/20898
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Martin Roth <martinroth@google.com>
This patch fix the dependency for PMC common block code.
PMC block use SLP_TYP macros and acpi_sleep_from_pm1
function which is defined in arch/acpi.h and guarded
by CONFIG_ACPI_INTEL_HARDWARE_SLEEP_VALUES. So we need
PMC common block to depend on that config for proper
inclusion.
Change-Id: I88077626aff3efba0a95b3aaee0dbd71344ccb42
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/20964
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch provides the option to use the common CPU
Mp Init code by selecting a Config Token.
CONFIG_SOC_INTEL_COMMON_BLOCK_CPU_MPINIT config token can be
selected to use the Common MP Init Code, also where CPU MP Init is
done before FSP-S Init.
And if the config token is not selected, the old way of
implementation will exist, where MP Init is been done after
FSP-S.
CQ-DEPEND=CL:*397551
BUG=none
BRANCH=none
TEST=Build and boot Reef
Change-Id: I35d012785000d3f3bfcc34138cda9cd4591559f6
Signed-off-by: Barnali Sarkar <barnali.sarkar@intel.com>
Reviewed-on: https://review.coreboot.org/20895
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Early serial init on this superio is done by
superio/winbond/common/early_serial.c and no board
currently references this instance anymore.
Change-Id: Iab8dd93663fc78ed0d8c6a5313bb6a1884d1a043
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/20978
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Romstages of many 440BX boards included headers that are redundant.
Remove them as part of a bigger cleanup effort.
This finishes off what began in https://review.coreboot.org/20693.
Change-Id: I102a4f6e492eb607b7f88d4c6e15072a8b7fdc46
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: https://review.coreboot.org/20952
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
BUG=b:64468585
BRANCH=none
TEST=with the other sku-id related patches applied, coreboot obtains the
right SKU ID from EC
Change-Id: I96a0e030bbc5f1c98165e70353340c413f8dc352
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/20947
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
BUG=b:64468585
BRANCH=none
TEST=with the other sku-id related patches applied, coreboot obtains the
right SKU ID from EC
Change-Id: I82e324407b4b96495a3eb3d4caf110f9eae05116
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/20946
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The following changes can make system call into FSP siliconinit and exit
from that until payloads.
1. Add frame to call fspsinit.
2. Temporarily set all the USB OC pin to 0 to pass FSP siliconinit.
This patch was merged too early, and reverted.
Originally reviewed on https://review.coreboot.org/#/c/20581
Change-Id: I14eeba575af1658ff8013c9a00bd71013566bcbe
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/20687
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Initialize postcar frame once finish FSP memoryinit
This patch was merged too early and reverted.
Originally reviewed on https://review.coreboot.org/#/c/20534
Change-Id: Id36aa44bb7a89303bc22e92e0313cf685351690a
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/20688
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add LPC common code to be shared across Intel platforms.
Also add LPC library functions to be shared across platforms.
Use common LPC code for Apollo Lake soc. Update existing Apollolake
mainboard variants {google,intel,siemens} to use new common
LPC header file.
Change-Id: I6ac2e9c195b9ecda97415890cc615f4efb04a27a
Signed-off-by: Ravi Sarawadi <ravishankar.sarawadi@intel.com>
Reviewed-on: https://review.coreboot.org/20659
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
It was added with the words "Update the device header files" and we
maintained it for nearly 13 years :)
These functions are part of the SMBus spec but they are rarely used
and keeping them just in case increases the maintenance burden.
Change-Id: I69a1ea155a21463fc09b7b2c5b7302515a0030b2
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/20439
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The PMIO region was moved, but not updated in the ASL. Change to
generate \_PR table runtime and to report the correct PMIO region
and length.
Fix on Kahlee, where the EC overlaps the region:
[ 0.802721] cros_ec_lpcs GOOG0004:00: couldn't reserve region0
[ 0.807446] cros_ec_lpcs: probe of GOOG0004:00 failed with error -16
BUG=b:63902389
BRANCH=none
TEST=Cros_ec_lps can reserve the region. ACPI tables are correct.
Change-Id: I870f810cc5d2edc0b842478cde5b3c164ed3b47f
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/20910
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Our current struct for I2C segments `i2c_seg` was close to being compa-
tible to the Linux version `i2c_msg`, close to being compatible to SMBus
and close to being readable (e.g. what was `chip` supposed to mean?) but
turned out to be hard to fix.
Instead of extending it in a backwards compatible way (and not touching
current controller drivers), replace it with a Linux source compatible
`struct i2c_msg` and patch all the drivers and users with Coccinelle.
The new `struct i2c_msg` should ease porting drivers from Linux and help
to write SMBus compatible controller drivers.
Beside integer type changes, the field `read` is replaced with a generic
field `flags` and `chip` is renamed to `slave`.
Patched with Coccinelle using the clumsy spatch below and some manual
changes:
* Nested struct initializers and one field access skipped by Coccinelle.
* Removed assumption in the code that I2C_M_RD is 1.
* In `i2c.h`, changed all occurences of `chip` to `slave`.
@@ @@
-struct i2c_seg
+struct i2c_msg
@@ identifier msg; expression e; @@
(
struct i2c_msg msg = {
- .read = 0,
+ .flags = 0,
};
|
struct i2c_msg msg = {
- .read = 1,
+ .flags = I2C_M_RD,
};
|
struct i2c_msg msg = {
- .chip = e,
+ .slave = e,
};
)
@@ struct i2c_msg msg; statement S1, S2; @@
(
-if (msg.read)
+if (msg.flags & I2C_M_RD)
S1 else S2
|
-if (msg.read)
+if (msg.flags & I2C_M_RD)
S1
)
@@ struct i2c_msg *msg; statement S1, S2; @@
(
-if (msg->read)
+if (msg->flags & I2C_M_RD)
S1 else S2
|
-if (msg->read)
+if (msg->flags & I2C_M_RD)
S1
)
@@ struct i2c_msg msg; expression e; @@
(
-msg.read = 0;
+msg.flags = 0;
|
-msg.read = 1;
+msg.flags = I2C_M_RD;
|
-msg.read = e;
+msg.flags = e ? I2C_M_RD : 0;
|
-!!(msg.read)
+(msg.flags & I2C_M_RD)
|
-(msg.read)
+(msg.flags & I2C_M_RD)
)
@@ struct i2c_msg *msg; expression e; @@
(
-msg->read = 0;
+msg->flags = 0;
|
-msg->read = 1;
+msg->flags = I2C_M_RD;
|
-msg->read = e;
+msg->flags = e ? I2C_M_RD : 0;
|
-!!(msg->read)
+(msg->flags & I2C_M_RD)
|
-(msg->read)
+(msg->flags & I2C_M_RD)
)
@@ struct i2c_msg msg; @@
-msg.chip
+msg.slave
@@ struct i2c_msg *msg; expression e; @@
-msg[e].chip
+msg[e].slave
@ slave disable ptr_to_array @ struct i2c_msg *msg; @@
-msg->chip
+msg->slave
Change-Id: Ifd7cabf0a18ffd7a1def25d1d7059b713d0b7ea9
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/20542
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
The S3 resume path is broken on current Linux (4.11.3) and maybe
on older kernel, too.
Don't run the native graphics init when on S3 resume to fix it.
Tested on Lenovo T430.
Change-Id: Ifad145c86c2e8f019c507f97c889b70b7aa49882
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/20289
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This patch add new API to read LPSS CLK register. Also combine multiple
LPSS_CLOCK_CTL_REG writes into a single write inside lpss_clk_update function.
Change-Id: I420919ad9154c4cf426bc232c5eb59d95fd698d2
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/20938
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Simplify funciton names and remove reference to hudson in stoneyridge.
The southbridge in Stoney Ridge is Kern and hudson naming is
no longer accurate.
BUG=b:62200157
BRANCH=none
TEST=Build and booted on Kahlee.
Change-Id: Ide7a72dae69b881997101f1e37a1ac739901744d
Signed-off-by: Marc Jones <marcj303@gmail.com>
Reviewed-on: https://review.coreboot.org/20912
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Call weak method die_notify.
The method should be overwritten in mainboard directory to signal that
a fatal error had occurred. On boards that do share the same EC and where
the EC is capable of controlling LEDs or a buzzer the method can be
overwritten in EC directory instead.
Tested on Lenovo T500.
Change-Id: I71f8ddfc96047e8a0d39f084588db1fe2f251612
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/19696
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This allows the use of the native VGA init on boards featuring DVI-I
ports. Digital output is not supported.
Change-Id: I11a4dd68746e06c7e27ecf3e765bdd0d8cf40515
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/20890
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
These Kconfig options can be reused for the same purpose of selecting
the correct i2c pins for probing the analog output EDID in C native
graphic init. For this purpose this patch makes those options
independent of GFX_GMA and MAINBOARD_HAS_LIBGFXINIT.
Change-Id: If29c541d414e12b95d96ae9c249a7a20e863fe06
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/20894
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Copy from chrome-ec codebase, except for keeping the long-form license
header.
BUG=b:64468585
BRANCH=none
TEST=with the other sku-id related patches applied, coreboot obtains the
right SKU ID from EC
Change-Id: I513123547f3854945e827d2f7f6c0df6591886eb
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/20945
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Migrate opregion code from northbridge/intel/common to
drivers/intel/gma in preparation for consolidation with
soc/intel/common opregion code. Rename init_igd_opregion()
for clarity and disambiguation with other implementations.
Change-Id: I2d0bae98f04dbe7e896ca34e15f24d29b6aa2ed6
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/20582
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
- let the coreboot build system insert the two blobs to the coreboot image
- EC and Super I/O initialization
- ACPI support
Tested on 2760p, 8460p, 2570p, 8470p.
Issue:
Kernel gives the following error:
ACPI Error: No handler for Region [ECRM] (...) [EmbeddedControl]
ACPI Error: Region EmbeddedControl (ID=3) has no handler
TODO:
- consider moving the Super I/O initialization code to ramstage, or
reuse the existing sio/smsc/kbc1100 code (if so, how to add the
additional kbc1126 specific functions to sio/kbc1100)
- sort out the ACPI code which is mostly from the ACPI dump of vendor
firmware
- find out why the digitizer in hp/2760p doesn't work
- GRUB payload freezing on all HP Elitebooks may be related to EC
Change-Id: I6b16eb7e26303eda740f52d667dedb7cc04b4ef0
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/19072
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The minimum needed defines are included here and pm.h
will be updated when the PMC code for cannonlake is uploaded.
Change-Id: Idaf2be1258b3ec71fa449b88516bcb06c730d776
Signed-off-by: Brandon Breitenstein <brandon.breitenstein@intel.com>
Reviewed-on: https://review.coreboot.org/20849
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
1. Add a new variable to GNVS to store information during S3 suspend
whether UART debug controller is enabled.
2. On resume, read stored GNVS variable to decide if UART debug port
controller needs to be initialized.
3. Provide helper functions required by intel/common UARRT driver for
enabling controller on S3 resume.
BUG=b:64030366
Change-Id: Idd17dd0bd3c644383f273b465a16add184e3b171
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/20888
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
1. Add a new variable to GNVS to store information during S3 suspend
whether UART debug port controller is enabled.
2. On resume, read stored GNVS variable to decide if UART debug port
controller needs to be initialized.
3. Provide helpers functions required by intel/common UART driver for
enabling controller on S3 resume.
BUG=b:64030366
TEST=Verified behavior with different combinations:
1. Serial console enabled in coreboot: No change in behavior.
2. Serial console enabled only in kernel: coreboot initializes debug
controller on S3 resume.
3. Serial console not enabled in coreboot and kernel: coreboot skips
initialization of debug controller on S3 resume.
Change-Id: Iad1cc974bc396ecd55b05ebb6591eec6cedfa16c
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/20886
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
It has been observed on a number of platforms (baytrail, kaby lake)
that if serial console is not enabled in coreboot, but is enabled in
kernel (v4.4), then on resume kernel hangs. In order to fix this, add
support for enabling UART debug port controller on resume.
In order to decide whether UART debug port controller should be
enabled in ramstage, following things are checked in given order:
1. If coreboot has serial console enabled, there is no need to
re-initialize the controller.
2. This special action is taken only for UART debug port controller.
3. If boot is not S3 resume, then initialization is skipped.
4. Callback into SoC to check if it wants to initialize the
controller.
If all the above conditions are met, then UART debug port controller
is initialized and taken out of reset.
BUG=b:64030366
TEST=Verified with the entire patchset series that:
1. If coreboot does not have serial console enabled, but Linux kernel
has console enabled, then on resume, coreboot initializes UART debug
port controller.
2. If coreboot and Linux do not have serial console enabled, then
coreboot does not initialize UART debug port controller.
3. If coreboot has serial console enabled, there is no change in
behavior.
Change-Id: Ic936ac2a787fdc83935103c3ce4ed8f124a97a89
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/20835
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Add new API function lpss_is_controller_in_reset that returns whether
the LPSS controller is in reset. Also, add lpss.c to smm stage so that
lpss_is_controller_in_reset can be used in smihandler.
BUG=b:64030366
Change-Id: I0fe5c2890ee799b08482e487296a483fa8d42461
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/20885
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
1. Create a new function uart_lpss_init which takes the UART LPSS
controller out of reset and initializes and enables clock.
2. Instead of passing in m/n clock divider values as parameters to
uart_common_init, introduce Kconfig variables so that uart_lpss_init
can use the values directly without having to query the SoC.
BUG=b:64030366
TEST=Verified that UART still works on APL and KBL boards.
Change-Id: I74d01b0037d8c38fe6480c38ff2283d76097282a
Signed-off-by: Furquan Shaikh <furquan@chromium.org>
Reviewed-on: https://review.coreboot.org/20884
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
EvLoader is FSP module which loads and runs MMA tests.
With Change-Id Id31ddd4595e36c91ba7c888688114c4dbe4db86a, EvLoader
needs to be enabled with UPD param from coreboot.
Change-Id: Ifb860b98d6e6f21c116473a962f647e491e8546f
Signed-off-by: Pratik Prajapati <pratikkumar.v.prajapati@intel.com>
Reviewed-on: https://review.coreboot.org/20863
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Add a new Kconfig option to ignore memory fuses that limit the
maximum DRAM frequency to be used. The option is disabled by
default and should only enabled by experienced users as it
might decrease system stability or prevent a successful RAM
training.
Remove conflicting devicetree settings.
Change-Id: I35dd78a02bcaafce8ba522d253c795d7835bacae
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/20907
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Nicola Corna <nicola@corna.info>
Get rid of old hybrid graphics driver and use the new one.
1. Disable IGD and PEG in early romstage.
The PEG port will get disabled on devices that do not have a
discrete GPU. The power savings are around ~1Watt.
The disabled IGD does no longer waste GFX stolen memory.
2. Get rid of PCI driver
The Nvidia GPU can be handled by the generic PCI driver and allows
to use the ACPI _ROM generator for Switchable graphics.
3. Settings are stored in devicetree.
One driver for all Lenovo hybrid graphics capable devices.
4. Add support for Thinker1 GPU power handling.
Only boards that do use reference design 2012 are known to be
supported. Needs test on boards that do you use reference design 2013.
Should reduce idle power consumption when using IGD by ~5Watt.
Tested on Lenovo T430 without DGPU. PEG port is disabled.
Needs test on all devices.
Change-Id: Ibf18b75e8afe2568de8498b39a608dac8db3ba73
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/20794
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Arthur Heymans