In order for coreboot to assign resources properly the pci
drivers need to have th proper device ids. Add the host controller
and the LPC device ids for Lynx Point.
Resource assignment works correctly now w/o odd behavior because
of conflicts.
Change-Id: Id33b3676616fb0c428d84e5fe5c6b8a7cc5fbb62
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2638
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin.roth@se-eng.com>
Add support for SMM modules by leveraging the RMODULE lib. This allows
for easier dynamic SMM handler placement. The SMM module support
consists of a common stub which puts the executing CPU into protected
mode and calls into a pre-defined handler. This stub can then be used
for SMM relocation as well as the real SMM handler. For the relocation
one can call back into coreboot ramstage code to perform relocation in
C code.
The handler is essentially a copy of smihandler.c, but it drops the TSEG
differences. It also doesn't rely on the SMM revision as the cpu code
should know what processor it is supported.
Ideally the CONFIG_SMM_TSEG option could be removed once the existing
users of that option transitioned away from tseg_relocate() and
smi_get_tseg_base().
The generic SMI callbacks are now not marked as weak in the
declaration so that there aren't unlinked references. The handler
has default implementations of the generic SMI callbacks which are
marked as weak. If an external compilation module has a strong symbol
the linker will use that instead of the link one.
Additionally, the parameters to the generic callbacks are dropped as
they don't seem to be used directly. The SMM runtime can provide the
necessary support if needed.
Change-Id: I1e2fed71a40b2eb03197697d29e9c4b246e3b25e
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2693
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
There's a compile time error that we didn't catch since the
board defaults as used by the build bot won't expose it.
Just make watchdog_off() a no-op statement so there aren't any
stray semicolons in the preprocessor output.
Change-Id: Ib5595e7e8aa91ca54bc8ca30a39b72875c961464
Reported-by: 'lautriv' on irc.freenode.net/#coreboot
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/2627
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
We used to allow mainboards to override subsystems using
mainboard_pci_subsystem_vendor_id and mainboard_pci_subsystem_device_id.
Mechanisms have changed and the only occurrence of these names is in
the header.
Change-Id: Ic2ab13201a2740c98868fdf580140b7758b62263
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/2625
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
In the file `COPYING` in the coreboot repository and upstream [1]
just one space is used.
The following command was used to convert all files.
$ git grep -l 'MA 02' | xargs sed -i 's/MA 02/MA 02/'
[1] http://www.gnu.org/licenses/gpl-2.0.txt
Change-Id: Ic956dab2820a9e2ccb7841cab66966ba168f305f
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2490
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
According to both Haswell and the SandyBridge/Ivybridge
BWGs the save state area actually starts at 0x7c00 offset
from 0x8000. Update the em64t101_smm_state_save_area_t
structure and introduce a define for the offset.
Note: I have no idea what eptp is. It's just listed in the
haswell BWG. The offsets should not be changed.
Change-Id: I38d1d1469e30628a83f10b188ab2fe53d5a50e5a
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2515
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
For whatever reason tabs got inserted in the license header text.
Remove one occurrence of that with the following command [1].
$ git grep -l 'MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.'$'\t' | xargs sed -i 's,MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.[ ]*,MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.\ \ ,'
[1] http://sed.sourceforge.net/grabbag/tutorials/sedfaq.txt
Change-Id: Iaf4ed32c32600c3b23c08f8754815b959b304882
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-on: http://review.coreboot.org/2460
Tested-by: build bot (Jenkins)
Reviewed-by: Jens Rottmann <JRottmann@LiPPERTembedded.de>
Reviewed-by: Cristian Măgherușan-Stanciu <cristi.magherusan@gmail.com>
This moves uartmem_getbaseaddr() from an 8250-specific header to the
generic uart header. This is to accomodate non-8250 memory-mapped
UARTs.
Change-Id: Id25e7dab12b33bdd928f2aa4611d720aa79f3dee
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2422
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Add needed prototypes to .h files.
Remove unused variables and fix types in printk statements.
Add #IFNDEFs around #DEFINEs to keep them from being defined twice.
Fix a whole bunch of casts.
Fix undefined pre-increment behaviour in a couple of macros. These now
match the macros in the F14 tree.
Change a value of 0xFF that was getting truncated when being assigned
to a 4-bit bitfield to a value of 0x0f.
This was tested with the torpedo build.
This fixes roughly 132 of the 561 warnings in the coreboot build
so I'm not going to list them all.
Here is a sample of the warnings fixed:
In file included from src/cpu/amd/agesa/family12/model_12_init.c:35:0:
src/include/cpu/amd/amdfam12.h:52:5: warning: redundant redeclaration of 'get_initial_apicid' [-Wredundant-decls]
In file included from src/cpu/amd/agesa/family12/model_12_init.c:34:0:
src/include/cpu/amd/multicore.h:48:5: note: previous declaration of 'get_initial_apicid' was here
src/northbridge/amd/agesa/family12/northbridge.c:50:10: warning: no previous prototype for 'get_node_pci' [-Wmissing-prototypes]
src/northbridge/amd/agesa/family12/northbridge.c: In function 'get_hw_mem_hole_info':
src/northbridge/amd/agesa/family12/northbridge.c:302:13: warning: unused variable 'i' [-Wunused-variable]
src/northbridge/amd/agesa/family12/northbridge.c: In function 'domain_set_resources':
src/northbridge/amd/agesa/family12/northbridge.c:587:5: warning: format '%lx' expects argument of type 'long unsigned int', but argument 3 has type 'device_t' [-Wformat]
src/northbridge/amd/agesa/family12/northbridge.c:587:5: warning: format '%lx' expects argument of type 'long unsigned int', but argument 3 has type 'device_t' [-Wformat]
src/northbridge/amd/agesa/family12/northbridge.c:716:1: warning: format '%x' expects argument of type 'unsigned int', but argument 3 has type 'long unsigned int' [-Wformat]
In file included from src/mainboard/amd/torpedo/agesawrapper.h:31:0,
from src/northbridge/amd/agesa/family12/northbridge.c:38:
src/vendorcode/amd/agesa/f12/AGESA.h:1282:0: warning: "TOP_MEM" redefined [enabled by default]
In file included from src/northbridge/amd/agesa/family12/northbridge.c:34:0:
src/include/cpu/amd/mtrr.h:31:0: note: this is the location of the previous definition
In file included from src/mainboard/amd/torpedo/agesawrapper.h:31:0,
from src/northbridge/amd/agesa/family12/northbridge.c:38:
src/vendorcode/amd/agesa/f12/AGESA.h:1283:0: warning: "TOP_MEM2" redefined [enabled by default]
src/vendorcode/amd/agesa/f12/Proc/GNB/Modules/GnbPcieConfig/PcieInputParser.c: In function 'PcieInputParserGetNumberOfComplexes':
src/vendorcode/amd/agesa/f12/Proc/GNB/Modules/GnbPcieConfig/PcieInputParser.c:99:19: warning: operation on 'ComplexList' may be undefined [-Wsequence-point]
src/vendorcode/amd/agesa/f12/Proc/GNB/Modules/GnbPcieConfig/PcieInputParser.c: In function 'PcieInputParserGetLengthOfPcieEnginesList':
src/vendorcode/amd/agesa/f12/Proc/GNB/Modules/GnbPcieConfig/PcieInputParser.c:126:20: warning: operation on 'PciePortList' may be undefined [-Wsequence-point]
src/vendorcode/amd/agesa/f12/Proc/GNB/Modules/GnbPcieConfig/PcieInputParser.c: In function 'PcieInputParserGetLengthOfDdiEnginesList':
src/vendorcode/amd/agesa/f12/Proc/GNB/Modules/GnbPcieConfig/PcieInputParser.c:153:19: warning: operation on 'DdiLinkList' may be undefined [-Wsequence-point]
src/vendorcode/amd/agesa/f12/Proc/GNB/Modules/GnbPcieConfig/PcieInputParser.c: In function 'PcieInputParserGetComplexDescriptorOfSocket':
src/vendorcode/amd/agesa/f12/Proc/GNB/Modules/GnbPcieConfig/PcieInputParser.c:225:17: warning: operation on 'ComplexList' may be undefined [-Wsequence-point]
src/vendorcode/amd/agesa/f12/Proc/GNB/PCIe/Family/LN/F12PciePhyServices.c:246:1: warning: no previous prototype for 'PcieFmForceDccRecalibrationCallback' [-Wmissing-prototypes]
In file included from src/vendorcode/amd/agesa/f12/Proc/GNB/PCIe/Family/LN/F12PcieComplexConfig.c:58:0:
src/vendorcode/amd/agesa/f12/Proc/GNB/PCIe/Family/LN/LlanoComplexData.h:120:5: warning: large integer implicitly truncated to unsigned type [-Woverflow]
And fixed a boatload of these types of warning:
src/vendorcode/amd/agesa/f12/Proc/CPU/heapManager.c: In function 'HeapGetBaseAddress':
src/vendorcode/amd/agesa/f12/Proc/CPU/heapManager.c:687:17: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
src/vendorcode/amd/agesa/f12/Proc/CPU/heapManager.c:694:19: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
src/vendorcode/amd/agesa/f12/Proc/CPU/heapManager.c:701:23: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
src/vendorcode/amd/agesa/f12/Proc/CPU/heapManager.c:702:23: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
src/vendorcode/amd/agesa/f12/Proc/CPU/heapManager.c:705:23: warning: assignment makes integer from pointer without a cast [enabled by default]
src/vendorcode/amd/agesa/f12/Proc/CPU/heapManager.c:709:21: warning: assignment makes integer from pointer without a cast [enabled by default]
Change-Id: I97fa0b8edb453eb582e4402c66482ae9f0a8f764
Signed-off-by: Martin Roth <martin.roth@se-eng.com>
Reviewed-on: http://review.coreboot.org/2348
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Dave Frodin <dave.frodin@se-eng.com>
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
The name lapic_cluster is a bit misleading, since the construct is not local
APIC specific by concept. As implementations and hardware change, be more
generic about our naming. This will allow us to support non-x86 systems without
adding new keywords.
Change-Id: Icd7f5fcf6f54d242eabb5e14ee151eec8d6cceb1
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2377
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The name pci_domain was a bit misleading, since the construct is only
PCI specific in a particular (northbridge/cpu) implementation, but not
by concept. As implementations and hardware change, be more generic
about our naming. This will allow us to support non-PCI systems without
adding new keywords.
Change-Id: Ide885a1d5e15d37560c79b936a39252150560e85
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2376
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Rename _SPI_H_ to _SPI_GENERIC_H_ to match recent file rename.
Change-Id: I8b75e2e0a515fb540587630163ad289d0a6a0b22
Reported-by: Peter Stuge <peter@stuge.se>
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/2360
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
Since there are and will be other files in nb/sb folders, we change
the general spi.h to a file name which is not easy to be duplicated.
Change-Id: I6548a81206caa608369be044747bde31e2b08d1a
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/2309
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
And move the corresponding #define to speedstep.h
Change-Id: I8c884b8ab9ba54e01cfed7647a59deafeac94f2d
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/2339
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Use same console initialization procedure for all ARM stages (bootblock,
romstage, and ramstage):
#include <console/console.h>
...
console_init()
...
printk(level, format, ...)
Verified to boot on armv7/snow with console messages in all stages.
Change-Id: Idd689219035e67450ea133838a2ca02f8d74557e
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2301
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Revise console source file dependency (especially for EARLY_CONSOLE) and
interpret printk/console_init according to EARLY_CONSOLE setting (no-ops if
EARLY_CONSOLE is not defined).
Verified to boot on x86/qemu and armv7/snow. Disabling EARLY_CONSOLE correctly
stops romstage messages on x86/qemu (armv7/snow needs more changes to work).
Change-Id: Idbbd3a26bc1135c9d3ae282aad486961fb60e0ea
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2300
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: David Hendricks <dhendrix@chromium.org>
The console drivers (especially serial drivers) in Kconfig were named in
different styles. This change will rename configuration names to a better naming
style.
- EARLY_CONSOLE:
Enable output in pre-ram stage. (Renamed from EARLY_SERIAL_CONSOLE
because it also supports non-serial)
- CONSOLE_SERIAL:
Enable serial output console, from one of the serial drivers. (Renamed
from SERIAL_CONSOLE because other non-serial drivers are named as
CONSOLE_XXX like CONSOLE_CBMEM)
- CONSOLE_SERIAL_UART:
Device-specific UART driver. (Renamed from
CONSOLE_SERIAL_NONSTANDARD_MEM because it may be not memory-mapped)
- HAVE_UART_SPECIAL:
A dependency for CONSOLE_SERIAL_UART.
Verified to boot on x86/qemu and armv7/snow, and still seeing console
messages in romstage for both platforms.
Change-Id: I4bea3c8fea05bbb7d78df6bc22f82414ac66f973
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2299
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Some header content got duplicated during the initial porting
effort. This moves generic UART header stuff to exynos5-common
and leaves exynos5250 #defines in the AP-specific UART header.
Change-Id: Ifb6289d7b9dc26c76ae4dfcf511590b3885715a3
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2285
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This adds /src/include/gpio.h which currently contains generic GPIO
enums for type (in/out/alt) and 3-state logic.
The header was originally written for another FOSS project
(code.google.com/p/mosys) and thus the BSD license.
Change-Id: Id1dff69169e8b1ec372107737d356b0fa0d80498
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2265
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Summary:
Isolate CBFS underlying I/O to board/arch-specific implementations as
"media stream", to allow loading and booting romstage on non-x86.
CBFS functions now all take a new "media source" parameter; use
CBFS_DEFAULT_MEDIA if you simply want to load from main firmware.
API Changes:
cbfs_find => cbfs_get_file.
cbfs_find_file => cbfs_get_file_content.
cbfs_get_file => cbfs_get_file_content with correct type.
CBFS used to work only on memory-mapped ROM (all x86). For platforms like ARM,
the ROM may come from USB, UART, or SPI -- any serial devices and not available
for memory mapping.
To support these devices (and allowing CBFS to read from multiple source
at the same time), CBFS operations are now virtual-ized into "cbfs_media". To
simplify porting existing code, every media source must support both "reading
into pre-allocated memory (read)" and "read and return an allocated buffer
(map)". For devices without native memory-mapped ROM, "cbfs_simple_buffer*"
provides simple memory mapping simulation.
Every CBFS function now takes a cbfs_media* as parameter. CBFS_DEFAULT_MEDIA
is defined for CBFS functions to automatically initialize a per-board default
media (CBFS will internally calls init_default_cbfs_media). Also revised CBFS
function names relying on memory mapped backend (ex, "cbfs_find" => actually
loads files). Now we only have two getters:
struct cbfs_file *entry = cbfs_get_file(media, name);
void *data = cbfs_get_file_content(CBFS_DEFAULT_MEDIA, name, type);
Test results:
- Verified to work on x86/qemu.
- Compiles on ARM, and follow up commit will provide working SPI driver.
Change-Id: Iac911ded25a6f2feffbf3101a81364625bb07746
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2182
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
In order to provide some insight on what code is executed during
coreboot's run time and how well our test scenarios work, this
adds code coverage support to coreboot's ram stage. This should
be easily adaptable for payloads, and maybe even romstage.
See http://gcc.gnu.org/onlinedocs/gcc/Gcov.html for
more information.
To instrument coreboot, select CONFIG_COVERAGE ("Code coverage
support") in Kconfig, and recompile coreboot. coreboot will then
store its code coverage information into CBMEM, if possible.
Then, run "cbmem -CV" as root on the target system running the
instrumented coreboot binary. This will create a whole bunch of
.gcda files that contain coverage information. Tar them up, copy
them to your build system machine, and untar them. Then you can
use your favorite coverage utility (gcov, lcov, ...) to visualize
code coverage.
For a sneak peak of what will expect you, please take a look
at http://www.coreboot.org/~stepan/coreboot-coverage/
Change-Id: Ib287d8309878a1f5c4be770c38b1bc0bb3aa6ec7
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2052
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Reviewed-by: Martin Roth <martin@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Since coreboot is compiled into 32bit code, and userspace
might be 32 or 64bit, putting a pointer into the coreboot
table is not viable. Instead, use a uint64_t, which is always
big enough for a pointer, even if we decide to move to a 64bit
coreboot at some point.
Change-Id: Ic974cdcbc9b95126dd1e07125f3e9dce104545f5
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2135
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The 'VERSION' in CBFS header file is confusing and may conflict when being used
in libpayload.
Change-Id: I24cce0cd73540e38d96f222df0a65414b16f6260
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-on: http://review.coreboot.org/2098
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
This patch makes pre-RAM serial init more generic, particularly for
platforms which do not necessarily need cache-as-RAM in order to use
the serial console and do not have a standard 8250 serial port.
This adds a Kconfig variable to set romstage-* for very early serial
console init. The current method assumes that cache-as-RAM should
enable this, so to maintain compatibility selecting CACHE_AS_RAM will
also select EARLY_SERIAL_CONSOLE.
The UART code structure needs some rework, but the use of ROMCC,
romstage, and then ramstage makes things complex.
uart.h now includes all .h files for all uarts. All 2 of them.
This is actually a simplifying change.
Change-Id: I089e7af633c227baf3c06c685f005e9d0e4b38ce
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2086
Tested-by: build bot (Jenkins)
'nough said. It was broken since 2006.
Change-Id: I312ac07eee65d6bb8567851dd38064c7f51b3bd2
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2062
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
This just imports a header. We may wish to modify the i2c interface
and/or unify it with the smbus interface we currently have.
Change-Id: I314f3aef62be936456c6c3e164a3db2c473b8792
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/2079
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
GNU CC coverage needs free() and it's highly desirable to leave
the code as genuine as possible.
Change-Id: I4c821b9d211ef7a8e7168dc5e3116730693999c6
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2051
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
The SB800 and Hudson now support adding the IMC ROM which runs from the same
chip as coreboot. When the IMC is running, write or erase commands sent to
the spi bus will fail, and the IMC will die. To fix this, we send a request
to the IMC to stop fetching from the SPI rom while we write to it. This
process (in one form or another) is required for writes to the SPI bus while
the IMC is running.
Because the IMC can take up to 500ms to respond every time we claim the
bus, this patch tries to keep the number of times we need to do that to a
minimum. We only need to claim the bus on writes, and using a counter for
the semaphore allows us to call in once to claim the bus at the beginning
of a number of transactions and it will stay claimed until we release it
at the end of the transactions.
Claim() - takes up to 500ms hit
claim() - no delay
erase()
release()
claim() - no delay
write()
release()
Release()
Change-Id: I4e003c5122a2ed47abce57ab8b92dee6aa4713ed
Signed-off-by: Martin Roth <martin@se-eng.com>
Reviewed-on: http://review.coreboot.org/1976
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
and disable IO mapped UARTs on ARMV7 per default
Change-Id: I712c4677cbc8519323970556718f9bb6327d83c8
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/2021
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
stddef.h should be fairly generic across all platforms we'd want to
support, so let's move it to generic code.
Change-Id: I580c9c9b54f62fadd9ea97115933e16ea0b13ada
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/2007
Tested-by: build bot (Jenkins)
Instead of adding regparm(0) to each assembler function called
by coreboot, add an asmlinkage macro (like the Linux kernel does)
that can be different per architecture (and that is empty on ARM
right now)
Change-Id: I7ad10c463f6c552f1201f77ae24ed354ac48e2d9
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1973
Reviewed-by: David Hendricks <dhendrix@chromium.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Set_boot_successful depends on CMOS parts that non-PC80
platforms do not have. For now, make the current path
depend on CONFIG_PC80_SYSTEM, and make the alternative
empty.
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Change-Id: I68cf63367c8054d09a7a22303e7c04fb35ad0153
Reviewed-on: http://review.coreboot.org/1954
Tested-by: build bot (Jenkins)
Reviewed-by: David Hendricks <dhendrix@chromium.org>
This is an initial re-factoring of CBFS code to enable multiple
architectures. To achieve a clean solution, an additional field
describing the architecture has to be added to the master header.
Hence we also increase the version number in the master header.
Change-Id: Icda681673221f8c27efbc46f16c2c5682b16a265
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: David Hendricks <dhendrix@chromium.org>
Reviewed-on: http://review.coreboot.org/1944
Tested-by: build bot (Jenkins)
Add an init() function to the chip_operations which will be called
before bus enumeration. This allows to disable unused devices before
they get enumerated.
Change-Id: I63dd9cbfc7b5995ccafb7bf7a81dc71fc67906a0
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1623
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
e.g.
-#if CONFIG_LOGICAL_CPUS == 1
+#if CONFIG_LOGICAL_CPUS
This will make it easier to switch over to use the config_enabled()
macro later on.
Change-Id: I0bcf223669318a7b1105534087c7675a74c1dd8a
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1874
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
In principle this isn't necessary. However there's a byte (or several)
outside the first 14 bytes that are part of the RTC, and require
locking (century/altCentury).
Since their location is mostly unknown, guard writes properly.
Change-Id: I847cd4efa92722e8504d29feaf7dbfa5c5244b4e
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1868
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Using global variables with the TSEG is a bad idea because
they are not relocated properly right now. Instead make
the variables static and add accessor functions for the
rest of SMM to use.
At the same time drop the tcg/smi1 pointers as they are
not setup or ever used. (the debug output is added back
in a subsequent commit)
Change-Id: If0b2d47df4e482ead71bf713c1ef748da840073b
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1764
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The SMM GNVS pointer is normally updated only when the
ACPI tables are created, which does not happen in the
resume path.
In order to restore this pointer it needs to be available
at resume time. The method used to locate it at creation
time cannot be used again as that magic signature is
overwritten with the address itself. So a new CBMEM ID
is added to store the 32bit address so it can be found
again easily.
A new function is defined to save this pointer in CBMEM
which needs to be called when the ACPI tables are created
in each mainboard when write_acpi_tables() is called.
The cpu_index variable had to be renamed due to a conflict
when cpu/cpu.h is added for the smm_setup_structures()
prototype.
Change-Id: Ic764ff54525e12b617c1dd8d6a3e5c4f547c3e6b
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1765
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Let memory initialization code use the coreboot romstage console. This
simplifies the code and makes sure that all output is available in
/sys/firmware/log.
The pei_data structure is modified to allow passing the console output
function pointer. Romstage console_tx_byte() is used for this purpose.
Change-Id: I722cfcb9ff0cf527c12cb6cac09d77ef17b588e0
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/1823
Tested-by: build bot (Jenkins)
Reviewed-by: Martin Roth <martin@se-eng.com>
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Several small improvements of the stack checking code:
- move the CPU0 stack check right before jumping to the payload
and out of hardwaremain (that file is too crowded anyways)
- fix prototype in lib.h
- print size of used stack
- use checkstack function both on CPU0 and CPU1-x
- print amount of stack used per core
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Test: Boot coreboot on Link, see the following output:
...
CPU1: stack: 00156000 - 00157000, lowest used address 00156c68,
stack used: 920 bytes
CPU2: stack: 00155000 - 00156000, lowest used address 00155c68,
stack used: 920 bytes
CPU3: stack: 00154000 - 00155000, lowest used address 00154c68,
stack used: 920 bytes
...
Jumping to boot code at 1110008
CPU0: stack: 00157000 - 00158000, lowest used address 00157af8,
stack used: 1288 bytes
Change-Id: I7b83eeee0186559a0a62daa12e3f7782990fd2df
Reviewed-on: http://review.coreboot.org/1787
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
In hardwaremain() we can't add timestamps before we actually
reinitialized the cbmem area. Hence we kept the timestamps in
an array and added them later. This is ugly and intrusive and
helped hiding a bug that prevented any timestamps to be logged
in hardwaremain() when coming out of an S3 resume.
The problem is solved by moving the logic to keep a few timestamps
around into the timestamp code. This also gets rid of a lot of ugly
ifdefs in hardwaremain.c
Change-Id: I945fc4c77e990f620c18cbd054ccd87e746706ef
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1785
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This addition is in support of future multicore support in
coreboot. It also will allow us to remove some asssembly code.
The CPU "index" -- i.e., its order in the sequence in which
cores are brought up, NOT its APIC id -- is passed into the
secondary start. We modify the function to specify regparm(0).
We also take this opportunity to do some cleanup:
indexes become unsigned ints, not unsigned longs, for example.
Build and boot on a multicore system, with pcserial enabled.
Capture the output. Observe that the messages
Initializing CPU #0
Initializing CPU #1
Initializing CPU #2
Initializing CPU #3
appear exactly as they do prior to this change.
Change-Id: I5854d8d957c414f75fdd63fb017d2249330f955d
Signed-off-by: Ronald G. Minnich <rminnich@chromium.org>
Reviewed-on: http://review.coreboot.org/1820
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
If the event log is stored in flash that is not memory
mapped then it must use the SPI controller to read from
the flash device instead of relying on memory accesses.
In addition a new CBMEM ID is added to keep an resident
copy of the ELOG around if needed. The use of CBMEM for
this is guarded by a new CONFIG_ELOG_CBMEM config option.
This CBMEM buffer is created and filled late in the process
when the SMBIOS table is being created because CBMEM is
not functional when ELOG is first initialized.
The downside to using CBMEM is that events added via the
SMI handler at runtime are not reflected in the CBMEM copy
because I don't want to let the SMM handler write to memory
outside the TSEG region.
In reality the only time we add runtime events is at kernel
shutdown so the impact is limited.
Test:
1) Test with CONFIG_ELOG_CBMEM enabled to ensure the event
log is operational and SMBIOS points to address in CBMEM.
The test should involve at least on reboot to ensure that the
kernel is able to write events as well.
> mosys -l smbios info log | grep ^address
address | 0xacedd000
> mosys eventlog list
0 | 2012-10-10 14:02:46 | Log area cleared | 4096
1 | 2012-10-10 14:02:46 | System boot | 478
2 | 2012-10-10 14:02:46 | System Reset
3 | 2012-10-10 14:03:33 | Kernel Event | Clean Shutdown
4 | 2012-10-10 14:03:34 | System boot | 479
5 | 2012-10-10 14:03:34 | System Reset
2) Test with CONFIG_ELOG_CBMEM disabled to ensure the event
log is operational and SMBIOS points to memory mapped flash.
The test should involve at least on reboot to ensure that the
kernel is able to write events as well.
> mosys -l smbios info log | grep ^address
address | 0xffbf0000
> mosys eventlog list
0 | 2012-10-10 14:33:17 | Log area cleared | 4096
1 | 2012-10-10 14:33:18 | System boot | 480
2 | 2012-10-10 14:33:18 | System Reset
3 | 2012-10-10 14:33:35 | Kernel Event | Clean Shutdown
4 | 2012-10-10 14:33:36 | System boot | 481
5 | 2012-10-10 14:33:36 | System Reset
Change-Id: I87755d5291ce209c1e647792227c433dc966615d
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1776
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
- Fix handling of 5-byte Fast Read command in the ICH SPI
driver. This fix is ported from the U-boot driver.
- Allow CONFIG_SPI_FLASH_NO_FAST_READ to be overridden by
defining a name for the bool in Kconfig and removing the
forced select in southbridge config
- Fix use of CONFIG_SPI_FLASH_NO_FAST_READ in SPI drivers
to use #if instead of #ifdef
- Relocate flash functions in SMM so they are usable.
This really only needs to happen for read function pointer
since it uses a global function rather than a static one from
the chip, but it is good to ensure the rest are set up
correctly as well.
Change-Id: Ic1bb0764cb111f96dd8a389d83b39fe8f5e72fbd
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1775
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Applied function attribute to function definition to avoid 'conflicting type' warning.
Function declaration is in src/include/cpu.h
void secondary_cpu_init(unsigned int cpu_index)__attribute__((regparm(0)));
But function definition in lapic_cpu_init.c is missing the "__attribute__" part.
Change-Id: Idb7cd00fda5a2d486893f9866920929c685d266e
Signed-off-by: Han Shen <shenhan@google.com>
Reviewed-on: http://review.coreboot.org/1784
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
And move the pre-hardwaremain post code to 0x79
so it comes before hardwaremain at 0x80.
Emit these codes from ACPI OS resume vector as well
as the finalize step in bd82x6x southbridge.
Change-Id: I7f258998a2f6549016e99b67bc21f7c59d2bcf9e
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1702
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
src/include/timestamp.h is an interface describing timestamp storage
in coreboot. Exporting this interface is complicated by inclusion of
tsc.h which is needed only for the API and is not used in structure
definitions. Including this dependency only when needed fixes the
problem.
Change-Id: Ie6b1460b1dab0f5b5781cb5a9fa89a1a52aa9f17
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/1753
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
These events were initially for Chrome EC but they can be
applied to any EC.
Change-Id: I0eba9dbe8bde506e7f9ce18c7793399d40e6ab3b
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1746
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
http://netbsd.gw.com/cgi-bin/man-cgi?date++NetBSD-current
The NetBSD manual tells us the date in NetBSD doesn't take any flags
to enable or disable padding in the format.
By default, date pads numeric fields with zeroes. This will convert the
number to octal one. So add "0x" to convert it to BCD directly.
Change-Id: Icd44312acf01b8232f1da1fbaa70630d09007b40
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1804
Tested-by: build bot (Jenkins)
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Read out the post code from the previous boot and
log it if the code is not one of the expected values.
Test:
1) interrupt the boot of the system, this is easiest
with warm reset button when servo is attached
2) check the event log with mosys
65 | 2012-09-09 12:32:11 | Last post code in previous boot | 0x9d
Change-Id: Id418f4c0cf005a3e97b8c63de67cb9a09bc57384
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1744
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This will use 3 bytes of CMOS to keep track of the POST
code for the current boot while also leaving a record of
the previous boot.
The active bank is switched early in the bootblock.
Test:
1) clear cmos
2) reboot
3) use "mosys nvram dump" to verify that the first byte
contains 0x80 and the second byte contains 0xF8
4) powerd_suspend and then resume
5) use "mosys nvram dump" to verify that the first byte
contains 0x81 and the second byte contains 0xFD
Change-Id: I1ee6bb2dac053018f3042ab5a0b26c435dbfd151
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1743
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
We are seeing ME disabled and ME error events on some devices
and this extended info can help with debug.
Also fix a potential issue where if the log does manage to get
completely full it will never try to shrink it because the only
call to shrink the log happens after a successful event write.
Add a check at elog init time to shrink the log size.
Change-Id: Ib81dc231f6a004b341900374e6c07962cc292031
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1739
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The code that attempts to use the opmenu needs to have a special
case for write enable now that it is handled as an atomic prefix
and not as a standalone opcode.
To test, ensure that runtime SPI write via ELOG is successful by
checking the event log for a kernel shutdown reason code:
5 | 2012-08-27 11:09:48 | Kernel Event | Clean Shutdown
6 | 2012-08-27 11:09:50 | System boot | 26
7 | 2012-08-27 11:09:50 | System Reset
Change-Id: I527638ef3e2a5ab100192c5be6e6b3b40916295a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1710
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
Check the RTC on boot after RTC battery failure and ensure
that the reported build date matches what is reported:
> grep ^rtc /proc/driver/rtc
rtc_time : 01:00:21
rtc_date : 2012-08-16
Change-Id: If23f436796754c68ae6244ef7633ff4fa0a93603
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1709
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
(elog portion, support in EC code pending)
- Use a new EC command to read the last post code
from the previous boot
- If the post code is not well-known final boot
or resume code then log it
Change-Id: Id6249e9a182243eb87c777edd56f48de72125e77
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1703
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
Right now we only had a post code for "All devices enabled" which
was emitted at the wrong time (after the device initialize stage
rather than the device enable stage)
Change-Id: Iee82bff020de844c7095703f8d6521953003032c
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1693
Reviewed-by: Marc Jones <marcj303@gmail.com>
Tested-by: build bot (Jenkins)
Compose the name from Kconfig strings instead.
As the field is for debug print use only, a minor change in the output
should do no harm. The strings no longer include word "Mainboard".
Change-Id: Ifd24f408271eb5a5d1a08a317512ef00cb537ee2
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1635
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The constant field "name" in chip_operations is common to multiple
different devices within a chip and cannot reflect the actual device
as found on the platform.
The intention is that a driver sets dev->name as part of the device
enumeration sequence with the detected hardware type and revision.
The field is for debug print use only.
Change-Id: Ib7bf90ba3c618ad0cb715d80d6a937ceaae0adcf
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1634
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This adds proper support for turbo and super-low-frequency modes.
Calculation of the p-states has been rewritten and moved into an
extra file speedstep.c so it can be used for non-acpi stuff like
EMTTM table generation.
It has been tested with a Core2Duo T9400 (Penryn) and a Core Duo T2300
(Yonah) processor.
Change-Id: I5f7104fc921ba67d85794254f11d486b6688ecec
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1658
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
We had only some MSR definitions in there, which are used in speedstep
related code. I think speedstep.h is the better and less confusing place
for these.
Change-Id: I1eddea72c1e2d3b2f651468b08b3c6f88b713149
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: http://review.coreboot.org/1655
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
We only want to add data once per device. Using the one in
chip_operations is not very usable anyway, as different
devices under the same chip directory would need to output
entirely different sets of data.
Change-Id: I96690c4c699667343ebef44a7f3de1f974cf6d6d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1492
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins)
Disallow tracing while in SMM.
Change-Id: Icde17629bb06a615cc48f017fd0cd1f7b720e62d
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Reviewed-on: http://review.coreboot.org/1503
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
This patch aims to improve the microcode in CBFS handling that was
brought by the last patches from Stefan and the Chromium team.
Choices in Kconfig
- 1) Generate microcode from tree (default)
- 2) Include external microcode file
- 3) Do not put microcode in CBFS
The idea is to give the user full control over including non-free
blobs in the final ROM image.
MICROCODE_INCLUDE_PATH Kconfig variable is eliminated. Microcode
is handled by a special class, cpu_microcode, as such:
cpu_microcode-y += microcode_file.c
MICROCODE_IN_CBFS should, in the future, be eliminated. Right now it is
needed by intel microcode updating. Once all intel cpus are converted to
cbfs updating, this variable can go away.
These files are then compiled and assembled into a binary CBFS file.
The advantage of doing it this way versus the current method is that
1) The rule is CPU-agnostic
2) Gives user more control over if and how to include microcode blobs
3) The rules for building the microcode binary are kept in
src/cpu/Makefile.inc, and thus would not clobber the other makefiles,
which are already overloaded and very difficult to navigate.
Change-Id: I38d0c9851691aa112e93031860e94895857ebb76
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/1245
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
These declarations were never or no longer used.
Change-Id: Icdbfc0838d5021ea02ab031b643b3fe6361b39b4
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1489
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Factor CPU allocation out of AMD northbridge codes. As CPU topology
information is required for generation of certain ACPI tables, make
this code globally available.
For AMDK8 and AMDFAM10 northbridge, there is a possible case of
BSP CPU with lapicid!=0. We do not want to leave the lapic 0 from
devicetree unused, so always use that node for BSP CPU.
Change-Id: I8b1e73ed5b20b314f71dfd69a7b781ac05aea120
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1418
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Take a copy of BSP CPU's TOP_MEM and TOP_MEM2 MSRs to be distributed
to AP CPUs and factor out the debugging info from setup_uma_memory().
Change-Id: I1acb4eaa3fe118aee223df1ebff997289f5d3a56
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1387
Tested-by: build bot (Jenkins)
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The CPU can arbitrarily reorder calls to rdtsc, significantly
reducing the precision of timing using the CPUs time stamp counter.
Unfortunately the method of synchronizing rdtsc is different
on AMD and Intel CPUs. There is a generic method, using the cpuid
instruction, but that uses up a lot of registers, and is very slow.
Hence, use the correct lfence/mfence instructions (for CPUs that
we know support it)
Change-Id: I17ecb48d283f38f23148c13159aceda704c64ea5
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1422
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
Adding ranges directly into coreboot memory table raised issues
as those methods bypassed the MTRR setup. Such regions are now
added as resources, so declare the functions again as static.
Change-Id: If78613da40eabc5c99c49dbe2d6047cb22a71b69
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1415
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Tested-by: build bot (Jenkins)
Dropping mainboard's chip.h broke execution of the mainboard's enable
function and the addition of mainboard specific smbios tables.
The former was fixed by Kyosti in http://review.coreboot.org/1374
This patch fixes the breakage in static.c and also backs out a small
portion of Kyosti's patch (because it's not needed anymore)
Change-Id: I6fdea9cbb8c6041663bd36f68f1cae4b435c1f9b
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1421
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
The function is a noop for all but amd/serengeti_cheetah.
Change-Id: I09e2e710aa964c2f31e35fcea4f14856cc1e1dca
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1184
Tested-by: build bot (Jenkins)
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Some mainboards have really nice capabilities for posting, beyond
simple POST cards. Further, some can not use a POST card. This
change defines a weak symbol (mainboard_post) that can be overridden
by a real mainboard_post function.
If, for example, you'd like to do something fancy before the payload starts,
you can add this to mainboard.c:
void mainboard_post(u8 value)
{
switch(value){
case POST_TIME_TO_PARTY: some_fancy_lights();
break;
}
}
Maybe the post function should be an entry in the device. We're beginning to over-use
weak symbols.
BUG=None
TEST=Build and boot a google chromebook. Observe that it still works. Use it to drive
some pretty lights.
Change-Id: I3512d2ec34a66c747287191851c3f68b6a7cc1b2
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-on: http://review.coreboot.org/1397
Tested-by: build bot (Jenkins)
We thought about two ways to do this change. The way we decided to try
was to
1. drop all ops from devices in romstage
2. constify all devices in romstage (make them read-only) so we can
compile static.c into romstage
3. the device tree "devices" can be used to read configuration from
the device tree (and nothing else, really)
4. the device tree devices are accessed through struct device * in
romstage only. device_t stays the typedef to int in romstage
5. Use the same static.c file in ramstage and romstage
We declare structs as follows:
ROMSTAGE_CONST struct bus dev_root_links[];
ROMSTAGE_CONST is const in romstage and empty in ramstage; This
forces all of the device tree into the text area.
So a struct looks like this:
static ROMSTAGE_CONST struct device _dev21 = {
#ifndef __PRE_RAM__
.ops = 0,
#endif
.bus = &_dev7_links[0],
.path = {.type=DEVICE_PATH_PCI,{.pci={ .devfn = PCI_DEVFN(0x1c,3)}}},
.enabled = 0,
.on_mainboard = 1,
.subsystem_vendor = 0x1ae0,
.subsystem_device = 0xc000,
.link_list = NULL,
.sibling = &_dev22,
#ifndef __PRE_RAM__
.chip_ops = &southbridge_intel_bd82x6x_ops,
#endif
.chip_info = &southbridge_intel_bd82x6x_info_10,
.next=&_dev22
};
Change-Id: I722454d8d3c40baf7df989f5a6891f6ba7db5727
Signed-off-by: Ronald G. Minnich <rminnich@chromium.org>
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1398
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Commit 188e3c2ff0 dropped mainboard
out of the static device tree. This left dev_root->chip_ops unset,
and mainboard_ops.enable_dev() was no longer called.
Change-Id: I6d447c8049a66041b8bb36ec9aac3e7e0d20a99b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1374
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
If the CMOS is cleared or someone writes some random date/time
on purpose, the CMOS date register has a invalid date. This will
hurts some OS, like Windows 7, which hangs at MS logo forever.
When we detect that, we need to write a reasonable date in CMOS.
Alexandru Gagniuc:
Hmm, it would be interesting to use the date the coreboot image
was built and set that as the default date. At least until time
travel is invented.
Change-Id: Ic1c7a2d60e711265686441c77bdf7891a7efb42e
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1389
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
UMA region can be determined at any time after the amount
of RAM is known and before the uma_resource() call.
Change-Id: I2a0bf2d3cad55ee70e889c88846f962b7faa0c7e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1379
Reviewed-by: Zheng Bao <zheng.bao@amd.com>
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Reserved memory resources will get removed from memory table at
the end of write_coreboot_table(),
Change-Id: I02711b4be4f25054bd3361295d8d4dc996b2eb3e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1372
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
This reverts commit 042c1461fb.
It turned out that sending IPIs via broadcast doesn't work on
Sandybridge. We tried to come up with a solution, but didn't
found any so far. So revert the code for now until we have
a working solution.
Change-Id: I7dd1cba5a4c1e4b0af366b20e8263b1f6f4b9714
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1381
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Hide some details of the resource allocator from rest of the world.
These should come in handy when fixing some aspects of MTRR setup.
Change-Id: I8acad98f25e56cd8bae64fb52539d81ce94f9c73
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1367
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
Reviewed-by: Anton Kochkov <anton.kochkov@gmail.com>
Recent changes in EC/Vboot/U-boot have completely broken
the logging of developer and recovery modes.
Recovery mode may not be in VBNV, so if that is zero and
yet we are in recovery mode then assume it is there because
the button/key was pressed.
Since there may not be any actual developer mode switch
we look if option rom is loaded and the system is not
in recovery mode and consider that as developer mode.
Change-Id: I70104877b24de477217e1ff5b3a019aef22343ec
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1346
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This will log if the ME is disabled or has an error.
1) disable ME via EC console: gpioset PCH_HDA_SDO 1
2) boot the device
3) read eventlog with "mosys eventlog list"
71 | 2012-07-13 10:10:55 | Management Engine | Disabled
Change-Id: I9f6ee452d2aea76e6a5ea2cd50a50ff36245692a
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1345
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
EHCI debug allows to send message with 8 bytes length, but
we're only sending one byte in each transaction. Buffer up
to 8 bytes to speed up debug output.
Change-Id: I9dbb406833c4966c3afbd610e1b13a8fa3d62f39
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1357
Tested-by: build bot (Jenkins)
Reviewed-by: Nico Huber <nico.huber@secunet.com>
The linux kernel contains an SMI driver that was written by
me (Duncan) and upstreamed a couple years ago called GSMI.
This driver will format a parameter buffer and pass pointers
to this parameter buffer to the SMI handler. It uses this to
generate events for kernel shutdown reasons: Clean, Panic, Oops,
etc.
This function expects to be passed pointers into the SMM state
save area that correspond to the prameter buffer and the return
code, which are typically EAX and EBX.
The format of the parameter buffer is defined in the kernel
driver so we implement the same interface here in order to be
compatible.
GSMI_CMD_HANDSHAKE: this is an early call that it does to try
and detect what kind of BIOS is running.
GSMI_CMD_SET_EVENT_LOG: this contains a parameter buffer that
has event type and data. The kernel-specific events are
translated here and raw events are passed through as well which
allows any run-time event to be added for testing.
GSMI_CMD_CLEAR_EVENT_LOG: this command clears the event log.
First the gsmi driver must be enabled in the kernel with
CONFIG_GOOGLE_GSMI and then events can be added via sysfs
and events are automatically generated for various kernel
shutdown reasons.
These can be seen in the event log as the 'Kernel Event' type:
169 | 2012-06-23 15:03:04 | Kernl Event | Clean Shutdown
181 | 2012-06-23 16:26:32 | Kernl Event | Oops
181 | 2012-06-23 16:26:32 | Kernl Event | Panic
Change-Id: Ic0a3916401f0d9811e4aa8b2c560657dccc920c1
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1316
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This function is exported so it can be used in other
places that need similar relocation due to TSEG.
Change-Id: I68b78ca32d58d1a414965404e38d71977c3da347
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1310
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This patch extends the current smbios api to allow changing mainboard
serial and version during coreboot runtime. This is helpful if you
have an EEPROM etc. to access these informations and want to add
some quirks for broken hardware revision for the linux kernel.
This could be done via DMI_MATCH marco.
Change-Id: I1924a56073084e965a23e47873d9f8542070423c
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-on: http://review.coreboot.org/1232
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This maintains a 32bit monotonically increasing boot counter
that is stored in CMOS and logged on every non-S3 boot when
the event log is initialized.
In CMOS the count is prefixed with a 16bit signature and
appended with a 16bit checksum.
This counter is incremented in sandybridge early_init which is
called by romstage. It is incremented early in order notice
when reboots happen after memory init.
The counter is then logged when ELOG is initialized and will
store the boot count as part of a 'System boot; event.
Reboot a few times and look for 'System boot' events in the
event log and check that they are increasing. Also verify
that the counter does NOT increase when resuming from S3.
171 | 2012-06-23 16:02:55 | System boot | 285
176 | 2012-06-23 16:26:00 | System boot | 286
182 | 2012-06-23 16:27:04 | System boot | 287
189 | 2012-06-23 16:31:10 | System boot | 288
Change-Id: I23faeafcf155edfd10aa6882598b3883575f8a33
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1315
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This standared SMBIOS 0able describes the location and format
of the event log to the OS and applications. In this case the
pointer is a 32bit physical address pointer to the log in
memory mapped flash.
Look for SMBIOS type15 entry with 'dmidecode -t 15'
Handle 0x0004, DMI type 15, 23 bytes
System Event Log
Area Length: 4095 bytes
Header Start Offset: 0x0000
Header Length: 8 bytes
Data Start Offset: 0x0008
Access Method: Memory-mapped physical 32-bit address
Access Address: 0xFFB6F000
Status: Valid, Not Full
Change Token: 0x00000000
Header Format: OEM-specific
Supported Log Type Descriptors: 0
Change-Id: I1e7729e604000f197e26e69991a2867e869197a6
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1314
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
There are enough differences that it is worth defining the
proper map for the sandybridge/ivybridge CPUs. The state
save map was not being addressed properly for TSEG and
needs to use the right offset instead of pointing in ASEG.
To do this properly add a required southbridge export to
return the TSEG base and use that where appropriate.
Change-Id: Idad153ed6c07d2633cb3d53eddd433a3df490834
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1309
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This is based around the SMBIOS event log specification but
expanded with OEM event types to support more specific and
relevant system events.
It requires flash storage and a minimum 4K block (or flash block
size) that should be allocated in the FMAP.
A copy of the event log is maintained in memory for convenience
and speed and the in-memory copy is written to flash at specific
points.
The log is automatically shunk when it reaches a configurable
full threshold in order to not get stuck with a full log that
needs OS help to clear.
ELOG implements the specification published here:
http://code.google.com/p/firmware-event-log/wiki/FirmwareEventLogDesign
And is similar to what we use in other firmware at Google.
This implementation does not support double-buffered flash
regions. This is done because speed is valued over the log
reliability and it keeps the code simpler for the first version.
This is a large commit and by itself it just provides a new
driver that is made available to coreboot. Without additional
patches it is not very useful, but the end result is an event
log that will contain entries like this:
171 | 2012-06-23 16:02:55 | System boot | 285
172 | 2012-06-23 16:02:55 | EC Event | Power Button
173 | 2012-06-23 16:02:55 | SUS Power Fail
174 | 2012-06-23 16:02:55 | System Reset
175 | 2012-06-23 16:02:55 | ACPI Wake | S5
Change-Id: I985524c67f525c8a268eccbd856c1a4c2a426889
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1311
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Previous patches implemented stack overflow checking for the APs.
This patch builds on the BSP stack poisoning patch to implement
stack overflow checking for the BSP, and also prints out maximum
stack usage. It reveals that our 32K stack is ridiculously oversized,
especially now that the lzma decoder doesn't use a giant 16K on-stack
array.
Break the stack checking out into a separate function, which
we will later use for the APs.
CPU0: stack from 00180000 to 00188000:Lowest stack address 00187ad8
To test failure, change the DEADBEEF stack poison value in c_start.S
to something else. Then we should get an error like this:
Stack overrun on BSP.Increase stack from current 32768 bytes
CPU0: stack from 00180000 to 00188000:Lowest stack address 00180000
Separate the act of loading from the act of starting the payload. This
allows us better error management and reporting of stack use. Now we
see:
CPU0: stack from 00180000 to 00188000:Lowest stack address 00187ad8
Tested for both success and failure on Link. At the same time, feel free
to carefully check my manipulation of _estack.
Change-Id: Ibb09738b15ec6a5510ac81e45dd82756bfa5aac2
Signed-off-by: Ronald G. Minnich <rminnich@chromium.org>
Reviewed-on: http://review.coreboot.org/1286
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
When CONFIG_MICROCODE_IN_CBFS is enabled, find the microcode blob in
CBFS and pass it to intel_update_microcode() instead of using the
compiled in array.
CBFS accesses in pre-RAM and 'normal' environments are provided
through different API.
Change-Id: I35c1480edf87e550a7b88c4aadf079cf3ff86b5d
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/1296
Tested-by: build bot (Jenkins)
This lets the SPI driver and the LPC driver know about HM70 and NM70.
Change-Id: Id2f1e0e5586a2f7200b2d24785df3f2be890da98
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1300
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The oxpcie ramstage code calls uartmem_init after the PCI memory
allocation, but hte function was static and didn't have a prototype.
Change-Id: Iabc1a3d248aeaed29aaaa22504defac97c572326
Signed-off-by: Marc Jones <marc.jones@se-eng.com>
Reviewed-on: http://review.coreboot.org/1285
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
ELOG reads from RTC to build timestamp structure,
the resulting timestamp is decoded when printing events.
Change-Id: If26552074f18de5095b967b875a0ac1d815a5b31
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-on: http://review.coreboot.org/1302
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
Since coreboot is running very short, we don't free memory.
Hence, drop (dummy) free()
Change-Id: I6e2737f07c6b9f73ebfad7d124b97a57cb7454a3
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1274
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
We don't ever free memory in coreboot, hence drop spi_flash_free() and
spi_free_slave()
Change-Id: I0ca3f78574ceb4516e7d33c06ab1a58abfb3b0ec
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/1273
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
VGA is this part-legacy thing that can cause trouble...
For this, introduce device_t->disable(dev) method, in which a driver
can take care to deregister the device if necessary.
Change-Id: I3fecec07f402e530458b79eda30b2c274101fefa
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/1251
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
MTRR setup code can detect this and mark it as UC/WT/WC as suitable
for the specific hardware.
Change-Id: Ib7a3d450fc7c19e3ca72767dfb350412dd35c971
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1214
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Use of the uma_memory_base and _size variables is very scattered.
Implementation of setup_uma_memory() will appear in each northbridge.
It should be possible to do this setup entirely in northbridge
code and get rid of the globals in a follow-up.
Change-Id: I07ccd98c55a6bcaa8294ad9704b88d7afb341456
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1204
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Like ram_resource(), but reserved and not cacheable.
Switch all AMD northbridges to use this one.
Change-Id: I88515c6a0f59f80fd8607c390d0d4a2a35d805f2
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1203
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
This patch adds support for autogenerating the MPTABLE from
devicetree.cb. This is done by a write_smp_table() declared
weak in mpspec.c. If the mainboard doesn't provide it's own
function, this generic implementation is called.
Syntax in devicetree.cb:
ioapic_irq <APICID> <INTA|INTB|INTC|INTD> <INTPIN>
The ioapic_irq directive can be used in pci and pci_domain
devices. If there's no directive, the autogen code traverses
the tree back to the pci_domain and stops at the first device
which such a directive, and use that information to generate the
entry according to PCI IRQ routing rules.
Change-Id: I4df5b198e8430f939d477c14c798414e398a2027
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1138
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
PCI Type 2 config was a strange and never-used config mechanism.
It is unlikely that in the 13 years of coreboot's existence that
type 2 was ever used; it just made life complicated for everyone.
It lived long enough in coreboot to be replaced by mmioconf.
Prior to making the device tree visible in romstage we want to
get rid of type2.
Delete two files we don't need any more (yay!).
Replace two functions with one: pci_config_default, which returns
a pointer to the default config method. At some future time this
may change to mmio but for now it is old type1 style.
Change-Id: Icc4ccf379a89bfca8be43f305b68ab45d88bf0ab
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/1159
Tested-by: build bot (Jenkins)
Reviewed-by: Sven Schnelle <svens@stackframe.org>
CACHE_ROM_SIZE default is ROM_SIZE, the Flash device size set
in menuconfig. This fixes a case where 8 MB SPI flash MTRR setup
would not cover the bottom 4 MB when ramstage is decompressed.
Verify CACHE_ROM_SIZE is power of two.
One may set CACHE_ROM_SIZE==0 to disable this cache.
Change-Id: Ib2b4ea528a092b96ff954894e60406d64f250783
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1146
Tested-by: build bot (Jenkins)
Reviewed-by: Sven Schnelle <svens@stackframe.org>
The wrapper for Trinity. Support S3. Parme is a example board.
Change-Id: Ib4f653b7562694177683e1e1ffdb27ea176aeaab
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/1156
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The current code for initializing AP cpus has several shortcomings:
- it assumes APIC IDs are sequential
- it uses only the BSP for determining the AP count, which is bad if
there's more than one physical CPU, and CPUs are of different type
Note that the new code call cpu->ops->init() in parallel, and therefore
some CPU code needs to be changed to address that. One example are old
Intel HT enabled CPUs which can't do microcode update in parallel.
Change-Id: Ic48a1ebab6a7c52aa76765f497268af09fa38c25
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/1139
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Early HT-enabled CPUs do not serialize microcode updates within a core.
Solve this by running microcode updates on the thread with the smallest
lapic ID of a core only.
Also set MTRRs once per core only.
Change-Id: I6a3cc9ecec2d8e0caed29605a9b19ec35a817620
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: http://review.coreboot.org/1142
Tested-by: build bot (Jenkins)
Reviewed-by: Sven Schnelle <svens@stackframe.org>
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Remove all the repeated sections of code in cbtypes.h and place it
in a common location. Add include dir in vendor code's Makefile.
Change-Id: Ida92c2a7a88e9520b84b0dcbbf37cd5c9f63f798
Signed-off-by: Vikram Narayanan <vikram186@gmail.com>
Reviewed-on: http://review.coreboot.org/912
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
Requirements:
- must be in ramstage (locking flash while executing code from there
might not work)
- must be after cbmem is reinitialized (so the mrc cache copy of the
current run can be found)
Change-Id: I8028fb073349ce2b027ef5f8397dc1a1b8b31c02
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/1002
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This driver is taken from u-boot and adapted to match
coreboot. It still contains some hacks and is ICH specific
at places.
Change-Id: I97dd8096f7db3b62f8f4f4e4d08bdee10d88f689
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/997
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This change is taken from Linux. It allows to check for Kconfig
definitions in the preprocessor and source code using the same
idiom.
Long term plan is to remove our Kconfig hack to #define values to 0,
and this helps.
This includes a tiny modification to the macros to fix romcc support.
Change-Id: I0fddbea8c8ca215cf226acf39cb329b0ba0445a5
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/1005
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Many PCI devices share the very same driver despite having different
PCI device IDs, which causes a lot of copy and paste of driver
definitions.
This change introduces a way to specify the array of acceptable
device IDs in a single driver entry. As an example the Intel
{Sandy|Ivy} Bridge SATA driver is being modified to use a single
driver structure for all different SATA controller flavors, a few
more Ivy Bridge IDs are being added as well.
BUG=none
TEST=manual
. modified coreboot brought up an Ivy Bridge platform all the
way to Linux login screen.
Change-Id: I761c5611b93ef946053783f7a755e6c456dd6991
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/982
Tested-by: build bot (Jenkins)
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
rename from mainboard_apm_cnt to mainboard_smi_apmc to match the function
naming scheme of the other handlers. Add prototype for mainboard_smi_sleep
(mainboard specific S3 sleep handlers in SMM) that is required by Sandybridge.
Change-Id: Ib479397e460e33772d90d9d41dba267e4e7e3008
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/933
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
In order to use the generic microcode update code in the bootblock, cpu/cpu.h
needs ROMCC guards. Also, delete the unused struct device declaration and move
the struct bus declaration to where it's used.
Change-Id: I0cc731c555593946e931a680ec93994932530599
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/932
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
There is no reason for this to be a top level directory.
Some stuff from lib/ should also be moved to drivers/
Change-Id: I3c2d2e127f7215eadead029cfc7442c22b26814a
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/939
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
- add GPLv2 + copyright header after talking to Ron
- "bits" in struct microcode served no real purpose but
getting its address taken. Hence drop it
- use asm volatile instead of __asm__ volatile
- drop superfluous wrmsr (that seems to be harmless but
is still wrong) in read_microcode_rev
- use u32 instead of unsigned int where appropriate
- make code usable both in bootblock and in ramstage
- drop ROMCC style print_debug statements
- drop microcode update copy in Sandybridge bootblock
Change-Id: Iec4d5c7bfac210194caf577e8d72446e6dfb4b86
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/928
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Instead of opaque numbers like (1<<29), use
symbols like CR0_NoWriteThrough.
Change-Id: Id845e087fb472cfaf5f71beaf37fbf0d407880b5
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/833
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
1. Move the Stack to high memory.
2. Restore the MTRR before Coreboot jump to the wakeup vector.
Change-Id: I9872e02fcd7eed98e7f630aa29ece810ac32d55a
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Signed-off-by: zbao <fishbaozi@gmail.com>
Reviewed-on: http://review.coreboot.org/623
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
Add a memalign function and have malloc use it. Also,
change the default alignment for malloc to u64-aligned.
Change-Id: I0788637008f5cb5ac801d8bbdc430ca992c98e81
Signed-off-by: Ron Minnich <rminnich@gmail.com>
Reviewed-on: http://review.coreboot.org/887
Tested-by: build bot (Jenkins)
Reviewed-by: Mathias Krause <minipli@googlemail.com>
- preprocessor macros should not use defined(CONFIG_*) but
just CONFIG_*
- drop AMD CPU model 14XXX config variable use. Those do not exist.
- skip some delays on Sandybridge systems
- Count how long we're waiting for each AP to stop
- Skip speedstep specific CPU entries
Change-Id: I13db384ba4e28acbe7f0f8c9cd169954b39f167d
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: http://review.coreboot.org/871
Tested-by: build bot (Jenkins)
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
cache as ram does not usually cache the ram before it is up. Hence,
if romstage.c backs up resume memory, the involved memcpy is always
uncached. This makes resume very slow.
On Sandybridge we copy the memory later, after enabling caching, and
that allows us to resume in as little as 250ms.
Change-Id: I31a71ad4468679d39880cf9a8c4e497bb7addf8f
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/872
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
ChromeOS uses two extensions to the coreboot table:
- ChromeOS specific GPIO description for onboard switches
- position of verified boot area in nvram
Change-Id: I8c389feec54c00faf2770aafbfd2223ac9da1362
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/866
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Traditionally coreboot's SMM handler runs in ASEG (0xa0000),
"behind" the graphics memory. This approach has two issues:
- It limits the possible size of the SMM handler (and the
number of CPUs supported in a system)
- It's not considered a supported path anymore in newer CPUs.
Change-Id: I9f2877e46873ab2ea8f1157ead4bc644a50be19e
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Acked-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/842
Reviewed-by: Peter Stuge <peter@stuge.se>
Tested-by: build bot (Jenkins)
From wikipedia:
Intel Turbo Boost is a technology implemented by Intel in certain
versions of their Nehalem- and Sandy Bridge-based CPUs, including Core
i5 and Core i7 that enables the processor to run above its base
operating frequency via dynamic control of the CPU's "clock rate".
It is activated when the operating system requests the highest
performance state of the processor.
Change-Id: I166ead7c219083006c2b05859eb18749c6fbe832
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/844
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Add support for type 41 smbios tables (to be used by board
specific smbios handlers)
Change-Id: Id6af5e4b1f5c5c78c63759d24fdc7cf8537ae5e6
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/843
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
... and drop duplicate definition in via/epia-n code.
Change-Id: Id79daaaa35c4d412c8c1f621a3638d129681d331
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/820
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This affects the algorithm when determining when to
transform a range into a larger range with a hole.
It is needed when for when I switch on an 8MB TSEG
and cause the memory maps to go crazy.
Also add header defines for the SMRR.
Change-Id: I1a06ccc28ef139cc79f655a8b19fd3533aca0401
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: http://review.coreboot.org/765
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This adds a number of timestamps in ramstage and romstage
so we can figure out where execution time goes.
Change-Id: Iea17c08774e623fc1ca3fa4505b70523ba4cbf01
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/749
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
and initialize the TPM on S3 resume
This patch integrates the TPM driver and runs TPM resume upon an ACPI S3
resume without including any other parts of vboot.
We could link against vboot_fw.a but it is compiled with u-boot's CFLAGS
(that are incompatible with coreboot's) and it does a lot more than we
want it to do.
Change-Id: I000d4322ef313e931e23c56defaa17e3a4d7f8cf
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/731
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The cbmem console structure and car global data are put in their own section,
with the cbmem console coming after the global data. These areas are linked
to be where CAR is available and at the very bottom of the stack.
There is one shortcoming of this change:
The section created by this change needs to be stripped out by the Makefile
since leaving it in confuses cbfstool when it installs the stage in the image.
I would like to make the tools link those symbols at the right location but
leave allocation of that space out of the ELF.
Change-Id: Iccfb99b128d59c5b7d6164796d21ba46d2a674e0
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/727
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Use an int in CAR global data to store whether or not the OXPCIE serial card
is actually there. Also, time out if the card doesn't show up quickly enough,
don't continue initialization if it's not there, and don't make the
initialization routine default to a card if none is found.
Change-Id: I9c72d3abc6ee2867b77ab2f2180e6f01f647af8c
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/728
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
These are guarded by individual Kconfig entries. The deprecated
CONFIG_PCIE_TUNING defines have been removed in favor of using specific
config options.
This is the generic half, there is board-specific pieces
still to come that tune before and after ASPM is enabled.
Change-Id: I3fe46282eada67629e9eeeed07e487dff54f2729
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: http://review.coreboot.org/735
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
We need to provide u-boot access to several different CBMEM
sections. To do that, a common coreboot table structure is used,
just different tags match different coreboot table sections.
Also, the code is added to export CBMEM console and MRC cache
addresses through the same mechanism.
Change-Id: I63adb67093b8b50ee61b0deb0b56ebb2c4856895
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/724
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This change exports the timestamp table pointer through coreboot
table to make it possible for u-boot to add timestamps to the
table.
Inclusion of cbmem.h allows to drop external declarations in
coreboot_table.c.
Change-Id: Ia070198cee7a6ffdaeece03d9d15bd91e033b6d1
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/716
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Add CBMEM type for the console buffer section.
Change-Id: I02757c06d71e46af77b02b90b0e6018a37b62406
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/720
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The CBMEM console driver saves console output in a CBMEM area, which
then is made available to Linux applications for perusing.
There are some system limitations which need to be worked around
to achieve this goal:
- some console traffic is generated before DRAM is initialized,
leave alone CBMEM initialized.
- after the RAM based stage starts, a lot of traffic is generated
before CBMEM is initialized.
As a result, the console log lives in three different places -
the bottom of the cache as RAM space, the CBMEM buffer (where it
is expected to be) and a static buffer used early in the RAM
stage.
When execution starts (in the cache as RAM mode), the console
buffer is allocated at the bottom of the cache as RAM memory
address range. Once DRAM is initialized, the CBMEM structure is
initialized, and then the console buffer contents are copied from
the bottom of the cache as RAM space into the CBMEM area right
before the cache as RAM mode is disabled. The
src/lib/cbmem_console.c:cbmemc_reinit() takes care of the
copying.
At this point the cache as RAM memory is about to be disabled,
but the ROM stage is still going generating console output. To
make sure this output is not lost, cbmemc_reinit() saves the new
buffer address at a fixed location (0x600 was chosen for this),
and the actual "printing" function checks to see if the RAM is
already initialized (the stack is in RAM), and if so, gets the
console buffer pointer from this location instead of using the
cache as RAM address.
When the RAM stage starts, a static buffer is used to store the
console output, as the CBMEM buffer location is not known. Then,
when CBMEM is reinitialized, cbmemc_reinit() again takes care of
the copying.
In case the allocated buffers are not large enough, the excessive
data is dropped, and the copying routine adds some text to the
output buffer to indicate that there has been data lost and how
many characters were dropped.
Change-Id: I8c126e31db6cb2141f7f4f97c5047f39a8db44fc
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/719
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
This change adds 128K to the memory amount set aside for CBMEM in
case the CBMEM console is enabled (to keep the CBMEM 128K byte
aligned). The console buffer size is being set to 64K, which is
enough to accommodate the most verbose coreboot console and
u-boot console.
Change-Id: If583013dfb210de5028d69577675095c6fe2f3ab
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/725
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
These get used later for saving/restoring the MRC scrambler
seed values on each boot.
Change-Id: I6e23f17649bea6d22c4b279ed8d0e5cb6c0885e7
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: http://review.coreboot.org/717
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This patch adds code to initialize the time stamp collection
facility in coreboot. It adds a table in the CBMEM section, which
provides the base timer reading value (all other readings are
offsets of this one) and an array of timestamp id/timestamp value
pairs.
Just two values are being added now, this will have to be used
more extensively and also integrated into payloads to provide more
comprehensive boot process time measurements.
Also, since the CBMEM area could already contain a section (from the
previous run, before reset), when processing a section addition
request we should check if a section already exists and return its
address, if so.
Change-Id: I7ed9f5c400bc5432f228348b41fd19a67c36d533
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/713
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Tested-by: build bot (Jenkins)
We want to be able to share data between different phases of firmware
(rom stage/ram stage/payload). Coreboot CBMEM seems an appropriate
location for this data, but normally it is not initialized
until coreboot reaches the ram stage.
This change initializes the CBMEM while still in rom stage in
case CONFIG_EARLY_CBMEM_INIT is set.
Note that there is a discrepancy in how coreboot determines the
size of DRAM at rom and ram stages, get_top_of_ram() is used at
rom stage and is not defined for all platforms. Those platforms
will have to define this function should they enable the
CONFIG_EARLY_CBMEM_INIT flag.
Change-Id: I81691d45e28de59496fb227f2cca4e8c15ece717
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-on: http://review.coreboot.org/711
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Change-Id: I3f3585f15265aa1377f72ba23accf1adb08cb8ac
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Reviewed-on: http://review.coreboot.org/806
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
clang doesn't know about the side effect, so we have to tell it
that it's okay not to care about the result.
Change-Id: Ib11890bff6779e36cf09c178d224695ea16a8ae8
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/783
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Since cbfs_core.h provides a macro that uses ntohl, make sure ntohl is available by
including byteorder.h
Change-Id: I9ab8cb51bd680e861b28d5130d09547bb9ab3b1f
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-on: http://review.coreboot.org/709
Tested-by: build bot (Jenkins)
Reviewed-by: Peter Stuge <peter@stuge.se>
Packing a device tree into the coreboot table can easily make
the table exceed the current limit of 8KB. However, right now
there is no error handling in place to catch that case.
Increase the maximum memory usable for all tables from 64KB to
128KB and increase the maximum coreboot table size from 8KB
to 32KB.
Change-Id: I2025bf070d0adb276c1cd610aa8402b50bdf2525
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/704
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Because it's included everywhere anyways.
Change-Id: I99a9e6edac08df57c50ef3a706fdbd395cad0abc
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Reviewed-on: http://review.coreboot.org/691
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
We used several names for that same value, and hardcoded the value
at some more places.
They're all LOCAL_APIC_ADDR now (except for lapic specific code
that still uses LAPIC_DEFAULT_BASE).
Change-Id: I1d4be73b1984f22b7e84681edfadf0588a7589b6
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/676
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
This allows to add a PCI ID mapping function for option roms so that the same
option rom can be used for a series of devices / PCI IDs. Intel and AMD often
use the same option rom for a number of PCI devices with differend IDs.
A function to implement such a mapping could look like this (or anything else
appropriate):
/* some vga option roms are used for several chipsets but they only have one
* PCI ID in their header. If we encounter such an option rom, we need to do
* the mapping ourselfes
*/
u32 map_oprom_vendev(u32 vendev)
{
u32 new_vendev=vendev;
switch(vendev) {
case 0xa0118086:
new_vendev=0xa0018086;
break;
}
return new_vendev;
}
Change-Id: I1be7fe113b895075d43ea48fe706b039cef136d2
Reviewed-on: http://review.coreboot.org/573
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
Reviewed-by: Marc Jones <marcj303@gmail.com>
Added a macro in the post code list, which replaces hard coded
value in cpu/x86/cache/cache.c
Change-Id: I27cb27827272584a8a17a41c111e2dc155196a97
Signed-off-by: Vikram Narayanan <vikram186@gmail.com>
Reviewed-on: http://review.coreboot.org/572
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The current implementation calls die() if memory checking fails.
This isn't always what we want: one might want to print error registers,
or do some other error handling. Introduce ram_check_nodie() for that
reason. It returns 0 if ram check succeeded, otherwise 1.
Change-Id: Ib9a9279120755cf63b5b3ba5e0646492c3c29ac2
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/532
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
The current code uses static values for the physical address size
supported by a CPU. This isn't always the right value: I.e. on
model_6[ef]x Core (2) Duo CPUs physical address size is 36, while
Xeons from the same family have 38 bits, which results in invalid
MTRR setup. Fix this by getting the right number from CPUID.
Change-Id: If019c3d9147c3b86357f0ef0d9fda94d49d811ca
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/529
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The read_option macro still emitted CMOS_VSTART_*/CMOS_VEND_* symbols,
which fail without an option table (as no option_table.h defines them).
Discard them by using a macro instead of a static inline function.
Change-Id: I8d001f971681277a344b6788725746491546b607
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/442
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The base is now calculated automatically, and all mentions of that
config option were typical anyway (4GB - XIP_ROM_SIZE).
Change-Id: Icdf908dc043719f3810f7b5b85ad9938f362ea40
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/366
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
- move enable_usbdebug() declaration to usbdebug.h
- reinitialize debug driver in ramstage, as copying the data
structure from romstage doesn't work right now. This way of copying
data from romstage to ramstage is really board/cpu specific, and is
likely to break often. So don't do it.
Change-Id: I394678ded6679c1803e29eb691b926182bdcab68
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/355
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
That value is now generated from a code address and CONFIG_XIP_ROM_SIZE.
This works as MTRRs are fully specified by their size and any address
within the range.
Change-Id: Id35d34eaf3be37f59cd2a968e3327d333ba71a34
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Reviewed-on: http://review.coreboot.org/348
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Add information about memory mapped/io mapped base addresses.
and fix up libpayload to use the same structures
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Change-Id: I5f7b5eda6063261b9acb7a46310172d4a5471dfb
Reviewed-on: http://review.coreboot.org/261
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
In order to make sure AHCI/RAID ROM works correctly
For SB800_SATA_AHCI or SB800_SATA_RAID mode, SATA should
enable bus master and the ahci also should be enabled.
Change-Id: I9d9c557816d364d8373fe343860ad5fe45988200
Signed-off-by: Kerry She <kerry.she@amd.com>
Signed-off-by: Kerry She <shekairui@gmail.com>
Reviewed-on: http://review.coreboot.org/248
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
sb800 SATA device have different device id with different configure
mode, 4392h for RAID mode, 4393h for RAID5 mode
Change-Id: If54f7751f531c94ee725309a2a5c255390935ead
Signed-off-by: Kerry Sheh <kerry.she@amd.com>
Signed-off-by: Kerry Sheh <shekairui@gmail.com>
Reviewed-on: http://review.coreboot.org/226
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
This trivial change adds a prototype to an existing
header file to fix a build warning for the AMD family
12 cpus.
Change-Id: Ic666bfbef867d17607eaa0f59570aea987a31f93
Signed-off-by: Frank Vibrans <frank.vibrans@amd.com>
Signed-off-by: efdesign98 <efdesign98@gmail.com>
Reviewed-on: http://review.coreboot.org/218
Tested-by: build bot (Jenkins)
Reviewed-by: Marc Jones <marcj303@gmail.com>
This commit adds in some more fixes to AMD F14 compile
warnings. The change in the mtrr.c file is in prep-
aration for changes yet to com, but it is currently
innocuous.
Change-Id: I6b204fe0af16a97d982f46f0dfeaccc4b8eb883e
Signed-off-by: Frank Vibrans <frank.vibrans@amd.com>
Signed-off-by: efdesign98 <efdesign98@gmail.com>
Reviewed-on: http://review.coreboot.org/133
Tested-by: build bot (Jenkins)
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
The compiler is forced to emmit special functions on every
entry/exit of the function. Add a compile time option
to support it. Function entries will be printed in
the console. The CONFIG_TRACE has more documentation.
Patch for userspace tools will follow.
Change-Id: I2cbeb3f104892b034c8756f86ed05bf71187c3f3
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Reviewed-on: http://review.coreboot.org/178
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The core is data structures and basic file finding capabilities,
while option ROM handling, and loading stages and payloads is
"extended".
The core is rewritten to be BSD-l (its header already was), so
can be copied to libpayload verbatim.
It's also more robust in finding files in corrupted images, eg.
after partial erase or update.
Change-Id: Ic6923debf8bdf3c67c75746d3b31f3addab3dd74
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Reviewed-on: http://review.coreboot.org/114
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Bring from coreboot v1 support for initializing L2 cache on Slot 1
Pentium II/III CPUs, code names Klamath, Deschutes and Katmai.
Build tested on ASUS P2B-LS and P3B-F. Boot tested on P2B-LS with
Pentium III 600MHz, Katmai core.
Also add missing include of model_68x in slot_1, to address a
similar problem fixed for model_6bx by r5945.
Also change Deschutes CPU init sequence to match Katmai.
Change-Id: I502e8481d1a20f0a2504685e7be16b57f59c8257
Signed-off-by: Keith Hui <buurin@gmail.com>
Reviewed-on: http://review.coreboot.org/122
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Move the SMM MSR init to a code run per CPU. Introduce global SMM_BASE define,
later all 0xa0000 could be changed to use it. Remove the unnecessary test if
the smm_init routine is called once (it is called by BSP only) and also remove
if lock bit is set becuase this bit is cleared by INIT it seems.
Add the defines for fam10h and famfh to respective files, we do not have any
shared AMD MSR header file.
Tested on M2V-MX SE with dualcore CPU.
Change-Id: I1b2bf157d1cc79c566c9089689a9bfd9310f5683
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Reviewed-on: http://review.coreboot.org/82
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
The previous code does a full flush of the uart after every character.
Unfortunately, this can cause transmission delays on some serial
ports.
This patch changes the code so that it does a flush at the end of
every printk instead of at the end of every character. This reduces
the time it takes to transmit serial messages (up to 9% on my Asrock
e350m1 board). It also makes the transmission time more consistent
which is important when performing timing tests via serial
transmissions.
Change-Id: I6b28488b905da68c6d68d7c517cc743cde567d70
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Reviewed-on: http://review.coreboot.org/90
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Tested-by: build bot (Jenkins)
Reviewed-by: Rudolf Marek <r.marek@assembler.cz>
Reviewed-by: Sven Schnelle <svens@stackframe.org>
This change adds the wrapper code for the AMD Family12
cpus and the AMD Hudson-2 (SB900) southbridge to the cpu,
northbridge and southbridge folders respectively.
Change-Id: I22b6efe0017d0af03eaa36a1db1615e5f38da06c
Signed-off-by: Frank Vibrans <frank.vibrans@amd.com>
Signed-off-by: efdesign98 <efdesign98@gmail.com>
Reviewed-on: http://review.coreboot.org/53
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Overwriting the SMM Area on resume leaves us with
all variables cleared out, i.e., the GNVS pointer
is no longer available, which makes SMIF function
calls impossible.
Change-Id: I08ab4ffd41df0922d63c017822de1f89a3ff254d
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/34
Tested-by: build bot (Jenkins)
Reviewed-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
in the current code, the defines for the APM_CNT (0xb2) register
are duplicated in almost every place where it is used. define those
values in cpu/x86/smm.h, and only include this file.
And while at it, fixup whitespace.
Change-Id: Iae712aff53322acd51e89986c2abf4c794e25484
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/4
Tested-by: build bot (Jenkins)
motherboards can use this hook to get notified if someone writes
to the APM_CNT port (0xb2). If the hook returns 1, the chipset
specific hook is also skipped.
Change-Id: I05f1a27cebf9d25db8064f2adfd2a0f5759e48b5
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-on: http://review.coreboot.org/3
Reviewed-by: Patrick Georgi <patrick@georgi-clan.de>
Tested-by: build bot (Jenkins)
With the K8T800/M800 patch from r6367 the PCI IDs for the VIA chrome were
moved to pci_ids.h. The PCI ID for K8M890 chrome was copied incorrectly.
(3220 instead of 3230). This patch defines the correct PCI ID for this device.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6618 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Scott Duplichan <scott@notabs.org>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6594 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Note: enable AHCI in seabios and apply seabios patch:
http://www.mail-archive.com/seabios@seabios.org/msg00437.html
Signed-off-by: Scott Duplichan <scott@notabs.org>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6579 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Simplify
read_option(CMOS_VSTART_foo, CMOS_VLEN_foo, somedefault)
to
read_option(foo, somedefault)
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6565 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
example.
This newer version reflects the recent changes to further simplify the console
code and partly gets rid of some hacks in the previous version.
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6544 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
and baudrate, not hardcoded in addition to that.
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6538 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- shift most (romcc) code out of console.h into arch/x86/lib/romcc_console.c
- rename arch/x86/lib/printk_init.c to .../romstage_console.c
- drop FUNCTIONS_FOR_PRINT since __console_tx_* are already functions, so there
should not be any side effects to eliminating another indirection.
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6532 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
http://www.coreboot.org/pipermail/coreboot/2007-September/024665.html
It's about time we follow this advice.
Also move some manually set __PRE_RAM__ defines (ap_romstage.c) to the Makefile and
drop unused CPP define
Signed-off-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6482 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6462 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Acked-by: Sven Schnelle <svens@stackframe.org>
Reported-by: Stefan Reinauer <stefan.reinauer@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6423 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Allow user to add 'subsystemid <vendor> <device> [inherit]' to devicetree.cb for
PCI and PCI domain devices.
Example:
device pci 00.0 on
subsystemid dead beef
end
If the user wants to have this ID inherited to all subdevices/functions,
he can add 'inherit', like in the following example:
device pci 00.0 on
subsystemid dead beef inherit
end
If the user don't want to inherit a Subsystem for a single device, he can
specify 'subsystemid 0 0' on this particular device.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6420 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The K8T800 is almost identical to the K8T800Pro, also added to this patch.
The K8T800_OLD is also defined, which is an older version of the K8T800,
but which has no driver and early HT code yet. Also extended the K8M890 VGA
driver to work for the K8M800 (not tested). According to the datasheet, the
K8T890 and K8T800 are similar enough to be able to use the same
initialization code. At least for the K8T800, this is sufficient to have
a working HT link with the CPU, and to initialise the V-Link to the
southbridge.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6367 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Frank Vibrans <frank.vibrans@amd.com>
Acked-by: Marc Jones <marcj303@gmail.com
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6350 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This is so that boards can determine them on runtime based on hardware
properties, if so desired.
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Acked-by: Joseph Kellermann <Joseph.Kellermann@heitec.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6329 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6322 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- actually hook up usbdebug in printk/print_ for romstage
- make usbdebug.c more similar to the Linux kernel version it was
originally derived from.
- increase retries and timing for usbdebug init (at least one chipset
seems to need this)
- src/pc80/usbdebug_serial.c is not needed
- some small console cleanups
Signed-off-by: Stefan Reinauer <reinauer@google.com>
Acked-by: Patrick Georgi <patrick.georgi@secunet.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6315 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
have this go away again.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Kevin O'Connor <kevin@koconnor.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6273 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
cache that range instead of the first 1Meg. This reduces boot time by
about 1 second on epia-cn.
This patch also adds a MTRRphysMaskValid bit definition.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6272 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
to CBFS and adapt coreboot to use it.
Comments by Stefan and Mathias taken into account (except for
the build time failure if the table is missing when it should
exist and the "memory leak" in build_opt_tbl)
Signed-off-by: Patrick Georgi <patrick.georgi@secunet.com>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6268 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Kerry She <Kerry.she@amd.com>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6230 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
to FG (FooGlue). As the GX2 has no VIP port.
-Change the Memmory setup MSR register names so they correspond better to the
databook. (Part1)
This is less confusing for beginners.
-Add a MSR printing function to northbridge.c like in the Geode LX code.
-Remove the AES register names.(GX2 has no AES registers)
-Delete some unused code.
-Clean up GX2 northbridge code to match Geode LX code.
-Add missing copyright header to northbridge.c.
-Move hardcoded IRQ defining from northbridge.c to irq_tables.c .
Signed-off-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6221 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6209 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6208 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
coreboot made it kind of complicated to print a character on serial. Not quite
as complicated as UEFI, but too much for a good design. Fix it.
Signed-off-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6191 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
and do that only if resume is done.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6174 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Abuild tested. Please check all changes if I did not make any wrong while converting this to bytes.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6171 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6165 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
src/arch/x86.
Signed-off-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6161 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
the prefix was introduced in the early v2 tree many years ago
because our old build system "newconfig" could not handle two files with
the same name in different paths like /path/to/usb.c and
/another/path/to/usb.c correctly. Only one of the files would end up
being compiled into the final image.
Since Kconfig (actually since shortly before we switched to Kconfig) we
don't suffer from that problem anymore. So we could drop the sb700_
prefix from all those filenames (or, the <componentname>_ prefix in general)
- makes it easier to fork off a new chipset
- makes it easier to diff against other chipsets
- storing redundant information in filenames seems wrong
Signed-off-by: <stepan@coresystems.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6150 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
W83627DHG:
- Add proper "virtual LDN" handling for the LDNs that need it (i.e., those
that don't have their "enable" bit in bit 0 of the 0x30 register).
- Fix various I/O masks in the pnp_dev_info[] array as per
datasheet. Add missing PNP_IRQ0 to the W83627DHG_ACPI LDN.
W83627EHG:
- Similar to W83627DHG, improve the "virtual LDN" setup a bit (it was
mostly implemented already, though).
- Add missing PNP_IRQ0 to the W83627EHG_ACPI LDN.
Also: Fix up devicetree.cb of all boards using W83627DHG/W83627EHG to adapt
for the virtual LDNs.
include/device/pnp.h: Add comment that 'function' (which refers to the
LDN and should probably be renamed later) has to be at least 16 bits
wide. In theory LDNs could use u8, but due to the virtual LDN info being
encoded in the "high byte" of 'function' it must be at least u16.
asrock/939a785gmh/romstage.c: Drop unused GPIO6_DEV.
ibase/mb899/romstage.c: Use DUMMY_DEV instead of a specific LDN (serial
port 1 in this case) to avoid confusion. The global registers
manipulated there are accessible from any LDN.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6140 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2) the patch implements get_cbmem_toc in chipset specific way if defined.
On Intel targets it should be unchanged. On K8T890 the the cbmem_toc is read from NVRAM. Why you ask? Because we cannot do it as on intel, because the framebuffer might be there making it hard to look for it in memory (and remember we need it so early that everying is uncached)
3) The patch removes hardcoded limits for suspend/resume save area (it was 1MB) on intel. Now it computes right numbers itself.
4) it impelements saving the memory during CAR to reserved range in sane way. First the sysinfo area (CAR data) is copied, then the rest after car is disabled (cached copy is used). I changed bit also the the copy of CAR area is now done uncached for target which I feel is more right.
I think I did not change the Intel suspend/resume behaviour but best would be if someone can test it. Please note this patch was unfinished on my drive since ages and it would be very nice to get it in to prevent bit rotten it again.
Now I feel it is done good way and should not break anything. I did a test with abuild and it seems fine.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Stefan Reinauer <stepan@coreboot.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6117 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
initializing VGA happens pretty much as the last thing before starting the
payload. Hence, drop VGA console support, as we did in coreboot v3.
- Drop VGA and BTEXT console support.
Console is meant to be debugging only, and by the time graphics comes up
99% of the risky stuff has already happened. Note: This patch does not remove
hardware init but only the actual output functionality.
The ragexl driver needs some extra love, but that's for another day
- factor out die() and post()
- drop some leftover RAMBASE < 0x100000 checks.
Signed-off-by: Stefan Reinauer <stepan@coreboot.org>
Acked-by: QingPei Wang<wangqingpei@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6111 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- VIA VT8235: Do the shift in smbus_read_byte() as all other chipsets do.
- spd.h: Move RC00-RC63 #defines here, they were duplicated in lots of
romstage.c files and lots of spd_addr.h files. Don't even bother for
those spd_addr.h which aren't even actually used, drop them right away.
- Replace various 0x50 hardcoded numbers with DIMM0, 0x51 with DIMM1,
and 0xa0 with (DIMM0 << 1) where appropriate.
- Various debug.c files: Replace SMBUS_MEM_DEVICE_START with DIMM0,
SMBUS_MEM_DEVICE_END with DIMM7, and drop useless SMBUS_MEM_DEVICE_INC.
- VIA VX800: Drop unused SMBUS_ADDR_CH* #defines.
- VIA VT8623: Do the shift in smbus_read_byte() as all other chipsets do.
Then, replace 0xa0 (which now becomes 0x50) with DIMM0.
- alix1c/romstage.c, alix2d/romstage.c: Adapt to recent bit shift changes.
- Various files: Drop DIMM_SPD_BASE and/or replace it with DIMM0.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6100 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
addressing scheme to match the rest of the tree
(0x50 instead of 0xa0).
abuild tested.
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6099 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6087 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Patrick Georgi <patrick@georgi-clan.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6085 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
-- When building for UMA, reduce the limit for DRAM below 4GB
from E0000000 to C0000000. This is needed to accomodate the
UMA frame buffer.
-- Correct problem where msr C0010010 bits 21 and 22 (MtrrTom2En
and Tom2ForceMemTypeWB) are not set consistently across cores.
-- Enable TOM2 only if DRAM is present above 4GB.
-- Use AMD Tom2ForceMemTypeWB feature to avoid the need for
variable MTRR ranges above 4GB.
-- Add above4gb flag argument to function x86_setup_var_mtrrs. Clearing
this flag causes x86_setup_var_mtrrs() to omit MTRR ranges for
DRAM above 4GB. AMD systems use this option to conserve MTRRs.
-- Northbridge.c change to deduct UMA memory from DRAM size reported
by ram_resource. This corrects a problem where mtrr.c generates an
unexpected variable MTRR range.
-- Correct problem causing build failure when CONFIG_GFXUMA=1 and
CONFIG_VAR_MTRR_HOLE=0.
-- Reserve the UMA DRAM range for AMD K8 as is already done for AMD
family 10h.
Tested with mahogany on ECS A780G-GM with 2GB and 4GB.
Tested with mahogany_fam10 on ECS A780G-GM with 2GB and 4GB.
Signed-off-by: Scott Duplichan <scott@notabs.org>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6067 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Needed to change class from raid to ide so seabios can boot from it.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6061 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also:
- Improve a few code comments, fix typos, etc.
- Change a few more variable types to u8/u16/u32 etc.
- Make some very long lines fit into 80chars/line.
- Drop a huge duplicated comment, use "@see" to refer to the other one.
- Reduce nesting level a bit by restructuring some code chunks.
- s/Config.lb/devicetree.cb/ in a few places.
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6019 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
variant. It also adds additional dev_find_device calls in k8t890_ctrl.c for
subfunctions 3 and 7.
Signed-off-by: Tobias Diedrich <ranma+coreboot@tdiedrich.de>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6012 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also, change the GX2 boards to use it.
Add a processor speed setting function in human readable MHz and remove
the useless and broken PLLMSR settings (the processor speed was hardcoded
to 366MHz in pll_reset.c).
Signed-off-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6011 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also, add a copyright header to pll_reset.c.
Signed-off-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@6009 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Whitespace and indentation fixes in various places.
- Fix various typos.
- Use u8, u16 etc. everywhere.
Abuild-tested.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5962 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Macros for the register addresses for the MTRR MSRs are already defined
in include/cpu/x86/car.h. This patch uses those macros instead of
creating a second instance of that same data.
I also added a few macros to the amd mtrr.h to make the MSR naming more
consistent.
Signed-off-by: Warren Turkal <wt@penguintechs.org>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5942 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The following functions are moved to devices/device_util.c:
- ram_resource()
- tolm_test()
- find_pci_tolm()
There are only two tolm_test() / find_pci_tolm() which differ from the
defaults, one of them can easily be eliminated in a follow-up patch,
maybe even both, but for now keep it simple and only eliminate the majority.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5937 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- move EHCI_BAR and EHCI_DEBUG_OFFSET to Kconfig to be set by USB debug port enabled southbridges
- drop USB debug code includes from romstage.cs and use romstage-srcs in the build system instead
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5911 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This makes the CAR implementations a lot more readable, shorter and
easier to follow, and also reduces the amount of uselessly duplicated code.
For example there are more than 12 open-coded "enable cache" instances
spread all over the place (and 12 "disable cache" ones), multiple
"enable mtrr", "save BIST", "restore BIST", etc. etc.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5902 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Use some more #defines instead of hard-coding values.
- Merge multiple movl/orl or movl/andl lines into one where possible.
- Add some TODOs in places which seem to have either an incorrect
code or incorrect comment.
- Fix typos: s/for/from/, s/BSC/BSP/, s/size/carsize/.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5890 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The fill_processor_name() function was duplicated in multiple
model_*_init.c files, move it into a new src/cpu/x86/name
directory.
The strcpy() function was also duplicated multiple times, move it
to <string.h> where we already have similar functions.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5879 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
statement to those files that actually need it. This significantly
reduces the number of dependencies, so it's no longer extremely ugly to
specify them manually (see the src/pc80/Makefile.inc portion)
- Add double include guards around option_table.h defines
- Also, drop the AMD DBM690T work around for the issue
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5838 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Add missing license headers, or missing (C) lines to various files.
(most are from AMD / Yinghai Lu, based on svn logs)
- src/include/ehci.h was taken from the Linux kernel. Updating it to
the latest version from git HEAD while I'm at it (build-tested with
one board). It also sports some new EHCI 1.1 addendum #defines which
we may or may not need.
This new file also already has a proper GPL header.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5828 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Root cause: After function STOP_CAR_AND_CPU disables cache as
ram, the cache as ram stack can no longer be used. Called
functions must be inlined to avoid stack usage. Also, the
compiler must keep local variables register based and not
allocated them from the stack. With gcc 4.5.0, some functions
declared as inline are not being inlined. This patch forces
these functions to always be inlined by adding the qualifier
__attribute__((always_inline)) to their declaration.
Signed-off-by: Scott Duplichan <scott@notabs.org>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5818 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
to those files that actually need it. This significantly reduces the number of
dependencies, so it's no longer extremely ugly to specify them manually (see
the src/pc80/Makefile.inc portion)
Also, drop the AMD DBM690T work around for the issue.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5762 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
board porter: printk should always be available in CAR mode.
Also drop CONFIG_USE_INIT, it's only been selected on one ASROCK board
but it's not been used there. Very odd.
There is one usage of CONFIG_USE_INIT which was always off in
src/cpu/intel/car/cache_as_ram.inc and we have to figure out what to do with
those few lines.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5682 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also clean up gx2def.h and geode_post_code.h a little.
abuild tested and boot tested on a Wyse S50.
Signed-off-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5671 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Nils Jacobs <njacobs8@hetnet.nl>
Acked-by: Joseph Smith <joe@settoplinux.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5669 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This resolves problems with terminated DRAM modules.
Signed-off-by: Edwin Beasant <edwin_beasant@virtensys.com>
Acked-by: Roland G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5629 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
there is no free list.
Converting resource arrays to lists reduced the size of each device
struct from 1092 to 228 bytes.
Converting link arrays to lists reduced the size of each device struct
from 228 to 68 bytes.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5626 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
coreboot is direct. This patch does it.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5586 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5564 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5563 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
also the GCC generated code and it looks all right. Please test on some
multicore CPU.
I added the "memory" clobber to read_cr0 / write_cr0 function as it is in Linux
Kernel. Seems that if this is missing, GCC is too smart and messes the order
of reads/writes to CR0 (not tested if really a problem here, but be safe for
future users of this function ;)
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5562 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
romstage.c files in mainboards.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5539 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
it centrally in console/console.h instead.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5538 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
romstage.c.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5528 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
while others dislike them being extra commits, let's clean them up once and
for all for the existing code. If it's ugly, let it only be ugly once :-)
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5507 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
geode lx and amd opteron don't use this yet.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5499 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
(which could at some time hold global post code definitions, too)
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5498 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
* integrate vsm init into normal x86.c code (so it can run above 1M)
* call void main(unsigned long bist) except void cache_as_ram_main(void)
on Geode LX (as we do on almost all other platforms now)
* Unify Geode LX MSR setup (will bring most non-working LX targets back
to life)
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5471 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2. Add support for Micro-FCBGA 479 Celeron and PIII's
3. Add support for model_6bx and microcode updates
4. Add support for CAR and Tinybootblock on RCA RM4100 and Thomson
IP1000
Build and boot tested.
Signed-off-by: Joseph Smith <joe@settoplinux.org>
The change to CAR reveiled a few more warnings in the ICH4 and i830 code,
I fixed them on the fly.
Checking this in because my last two commits broke Joseph's CAR patch. This
version fixes the issues.
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5388 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5356 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- start naming all versions of post code output "post_code()"
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5344 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Only some assembler files still have \r\n ... Can we move that part to C
completely?
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5342 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
makes include/console/console.h and console/console.c usable both in
__PRE_RAM__ and coreboot_ram stages.
While debugging this, I removed an indirection from the e7520 ram init code
(same as we did on a couple of other chipsets, removes some register pressure
from romcc)
Also, drop remainders of CONFIG_USE_INIT (except the one odd piece of dead code
in cache_as_ram.inc)
Then some ap_romstage.c fixes, at least the nvidia/l1_2pvv compiled for me with
CONFIG_AP_CODE_IN_CAR set in Kconfig which it did not before.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5341 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
stupid idea. Instead include it where it is needed. And add some explicit
dependencies to it.
Also, error for missing IRQ_SLOT_COUNT for now, so we can fix up the boards.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5321 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- add some __PRE_RAM__ guards where needed
- use OPTION_TABLE_H
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5317 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
the information is already specified in cmos.layout. coreboot is changed
to use that version instead.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmai.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5313 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Only have multicore.h for both of them.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5311 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
appropriate. Also, factor out post_code() for __PRE_RAM__ code and drop it from
some mainboards.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5307 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Interesting enough, console_printk was only used in a single place and
duplicated a large part of console.h which is included in the same place.
Thus, just drop console_printk.c and we're one down with console complexity
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5274 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5266 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
1. Add some more prototypes to lib.h
2. Include console.h when not using romcc
3. Eliminate an unused function
4. Set a default for SSE2, since it is just for ramtest performance
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5260 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
seperatedly because both RS780 and SB700 will modify the pci_ids.h. It
maybe will cause conflict if the sequence the patches are applied is
different with the one they are created.
2. Dev 0-10 of RS780 has AMD's Vendor ID. So we think it is better to
define the Device ID as XXX_AMD_RS780_XXX. Does anyone think it is
better to move this definition to the AMD zone? That will split the
RS780 into two parts. Is it inappropriate?
Signed-off-by: Zheng Bao <zheng.bao@amd.com
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5217 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- call va_* directly if coreboot is running on GCC so we don't need
to maintain hacks to get to stdarg.h
- only define LIBGCC_FILE_NAME if it's an absolute path. GCC and LLVM
just print "libgcc.a" if the file is not there.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5215 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Replace set_init_ram_access with the call to set_var_mtrr.
Remove unused #include statments.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5201 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2. Use time.h for get_time() and move tb_freq into functions.c
3. Move read_io and write_io to io.c and make them static
4. Make a couple of functions static in interrupt.c
5. Refactor a cast from char[] to u64 to get rid of potential alignment problems and a warning
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5191 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Fix whitespace, alignment, and indentation in a few places.
- Some more consistency fixes in license headers.
- Fix incomplete license header: src/mainboard/msi/ms9652_fam10/devicetree.cb.
- Fix typo for LIMIT_HT_SPEED_1800: s/1.6GHz/1.8GHz/.
- Fix typo in src/mainboard/msi/ms9652_fam10/Kconfig: s/MS-9256/MS-9252/.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5182 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This is needed on the IP1000T to get VGA output. The VGA option rom will ask
through an SMI for hardware specifics (in form of a VBT, video bios table)
which the SMI handler copies into the VGA option rom.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5177 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5170 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
PS/2 keyboard API.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5152 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Fix typos.
- Whitespace and consistency fixes.
- Make "menuconfig" help easily readable in 80x25 terminals / xterms.
- Use full/correct prototype for cbfs_and_run_core() everywhere.
- More cosmetic fixes in license headers.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5146 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- allow northbridge and cpu handlers, too
- support for older rev 2 cpus
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5141 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- drop include/part and move files to include/
- get rid lots of warnings
- make resource allocator happy with w83627thg
- trivial cbmem resume fix
- fix payload and log level settings in abuild
- fix kontron mptable for virtual wire mode
- drop some dead includes and dead code.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5136 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- drop x86emu + old biosemu in favor of YABEL
- Add YABEL_DIRECTHW to get the old biosemu behavior
- add support for vesa console using YABEL
- add coreboot table entry with console information
- add bootsplash support (reads /bootsplash.jpg from CBFS)
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Pattrick Hueper <phueper@hueper.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5135 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Consistently use the same wording and formatting for all license headers.
- Remove useless whitespace, add missing whitespace, fix indentation.
- Add missing "This file is part of the coreboot project." where needed.
- Change "(C) Copyright John Doe" to "Copyright (C) John Doe" for consistency.
- Add some missing "(C)" strings and copyright years where needed.
- Move random comments and file descriptions out of the license header.
- Drop incorrect file descriptions completely (e.g. lpc47m10x/Makefile.inc).
There should be no changes in _content_ of the license headers, if you spot
such changes that's a bug, please report!
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@5127 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Remove all remaining warnings from qemu.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4939 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
now handled more generically using CBFS.
Simplify the option ROM code in device/pci_rom.c, since there are only two ways
to get a ROM address now (CBFS and the device) and add an exception for qemu.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4925 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
__ROMCC__ now means "Don't use prototypes, since romcc doesn't support them."
__PRE_RAM__ means "Use simpler versions of functions, and no device tree."
There are probably some places where both are tested, but only one is needed.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4921 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This function is not called right now,... Please step in and fix up your code,
folks.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4913 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Declare superio functions to be static and remove duplicates.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4890 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4884 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Add static and const where possible.
- Turn some #warning entries into TODO comments.
- Add missing prototypes.
- Remove unused variables.
- Fix printf arguments or cast them as needed.
- Make sconfig output look better. Drop useless "PARSED THE TREE" output.
- Print "(this may take a while)" while building romcc. Add missing "\n".
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Myles Watosn <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4874 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
TODO
- x86emu need (imo) some common header with prototypes at least
- clog2, ulzma, hardwaremain prototypes added by this patch probably should
be moved to some header too.
- in src/devices/device_util.c prototype is before function because seems,
it is used only within same file, if not it should be moved to debug
section of prototypes in include/device/device.h
Signed-off-by: Maciej Pijanka <maciej.pijanka@gmail.com>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4871 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This code adds a very simple toc based memory manager for the high tables area.
The purpose of this code is to make it simpler and more reliable to find
certain data structures in memory. This will also make it possible to have ACPI
S3 Resume working without an ugly hole at 31MB.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4860 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
while ago...
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4841 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
drop claim that our files were blatantly copied, because they have been
rewritten a very long time ago.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4837 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
ppc port, some ambiguous use of CONFIG_IDE and an unused ide driver (we dropped
the filesystems already to be used with it) (somewhat trivial)
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4828 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4804 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Check the return value. Minor formatting and LAR -> CBFS.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4752 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
during early coreboot_ram), pci_{read,write}_config{8,16,32} will die().
This patch changes pci_{read,write}_config{8,16,32} to use the existing
PCI access method autodetection infrastructure instead of die()ing.
Until r4340, any usage of pci_{read,write}_config{8,16,32} in
coreboot_ram before the device tree was set up resulted in either a
silent hang or a NULL pointer dereference. I changed the code in r4340
to die() properly with a loud error message. That still was not perfect,
but at least it allowed people to see why their new ports died.
Still, die() is not something developers like to see, and thus a patch
to automatically pick a sensible default instead of dying was created.
Of course, handling PCI access method selection automatically for
fallback purposes has certain limitations before the device tree is set
up. We only check if conf1 works and use conf2 as fallback. No further
tests are done.
This patch enables cleanups and readability improvements in early
coreboot_ram code:
Without this patch:
dword = pci_cf8_conf1.read32(&pbus, sm_dev->bus->secondary,
sm_dev->path.pci.devfn, 0x64);
With this patch:
dword = pci_read_config32(sm_dev, 0x64);
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4646 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
instead of the versions in util/x86emu. Clean up this mess.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4594 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Tested on Via EPIA-NL8000EG with FILO payload booting FC9 (2.6.25
kernel) from SATA HDD.
ACPI is working for PCI interrupt routing, some memory stuff and
Soft-Off.
USB/SATA Working
VGA Console Working
X Working via Onboard AGP
Removed dsdt.c, fixed some whitespace.
Signed-off-by: Jon Harrison <bothlyn@blueyonder.co.uk>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4549 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
src/include/device/pci.h:75: warning: redundant redeclaration of 'pci_dev_init'
src/include/device/pci_rom.h:39: warning: previous declaration of 'pci_dev_init' was here
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4462 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
soon as there's an ACPI 2.0 or later table)
* add XSDT support
* add more table types
This patch will break at least the kontron (and possibly some new boards I
missed)
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4453 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
more flexible. Also some minore device allocator cleanups that sneaked
in.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4452 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
those symbols were left alone before, after this, they're
somewhat more in line with the rest of the tree.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4442 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The patch adds proper preprocessor guards and drops the malloc() prototype
because that's in stdlib.h
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4441 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
(according to the spec) to change the string in-situ,
even if glibc doesn't do it.
This avoids errors on Mac OS and Solaris.
Kill nrv2b support in CBFS (we have lzma),
slightly improve debug output in CBFS,
properly declare all functions of CBFS in the header.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4436 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Major changes:
1. Separate resource allocation into:
A. Read Resources
B. Avoid fixed resources (constrain limits)
C. Allocate resources
D. Set resources
Usage notes:
Resources which have IORESOURCE_FIXED set in the flags constrain the placement
of other resources. All fixed resources will end up outside (above or below)
the allocated resources.
Domains usually start with base = 0 and limit = 2^address_bits - 1.
I've added an IOAPIC to all platforms so that the old limit of 0xfec00000 is
still there for resources. Some platforms may want to change that, but I didn't
want to break anyone's board.
Resources are allocated in a single block for memory and another for I/O.
Currently the resource allocator doesn't support holes.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4394 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Jon Harrison <bothlyn@blueyonder.co.uk>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4389 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
It's basically done with the following script and some manual fixup:
VARS=`grep ^define src/config/Options.lb | cut -f2 -d\ | grep -v ^CONFIG | grep -v ^COREBOOT |grep -v ^CC`
for VAR in $VARS; do
find . -name .svn -prune -o -type f -exec perl -pi -e "s/(^|[^0-9a-zA-Z_]+)$VAR($|[^0-9a-zA-Z_]+)/\1CONFIG_$VAR\2/g" {} \;
done
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4381 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Marco Schmidt <mashpb@gmail.com>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4345 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This reverts commit eb7bb49eb5b48c39baf7a256b7c74e23e3da5660.
Stepan pointed out that "s" means string, which makes the following statement
in this commit message invalid: "Since we either have reserved space (which
we shouldn't do anything with in these two functions), an enum or a
hexadecimal value, unsigned int seemed like the way to go."
Signed-off-by: Luc Verhaegen <libv@skynet.be>
Acked-by: Luc Verhaegen <libv@skynet.be>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4335 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
To ease some of my debugging pain on the unichrome, i decided i needed to
move FB size selection into cmos, so i could test a size and then reset it
to the default after loading this value so that the next reboot uses the
(working) default again. This meant implementing set_option in parallel to
get_option.
get_option was then found to have inversed argument ordering (like outb) and
passing char * and then depending on the cmos layout length, which made me
feel quite uncomfortable. Since we either have reserved space (which we
shouldn't do anything with in these two functions), an enum or a
hexadecimal value, unsigned int seemed like the way to go. So all users of
get_option now have their arguments inversed and switched from using ints
to unsigned ints now.
The way get_cmos_value was implemented forced us to not overlap byte and to
have multibyte values be byte aligned. This logic is now adapted to do a
full uint32_t read (when needed) at any offset and any length up to 32, and
the shifting all happens inside an uint32_t as well. set_cmos_value was
implemented similarly. Both routines have been extensively tested in a
quick separate little program as it is not easy to get this stuff right.
build_opt_tbl.c was altered to function correctly within these new
parameters. The enum value retrieval has been changed strol(..., NULL, 10)
to stroul(..., NULL, 0), so that we not only are able to use unsigned ints
now but so that we also interprete hex values correctly. The 32bit limit
gets imposed on all entries not marked reserved, an unused "user_data" field
that appeared in a lot of cmos.layouts has been changed to reserved as well.
Signed-off-by: Luc Verhaegen <libv@skynet.be>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4332 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This code brings a rather complete set of VGA IO routines for whoever wants it.
These consist of the by now familiar read/write/mask sets. Due to the crazy
nature of VGA, an ancient standard with bits all over the place, it makes no
sense to define individual registers. You need a vga register spec at hand if
you want to do anything anyway. These IO routines are always exposed.
It also provides code to natively set up a 640x400 VGA textmode with an 8x16
font. The native VGA mode code is behind the OPTION_VGA option, as the font
really adds to the size of the compiled/compressed rom. The font is the one
also present in the linux kernel, but this file is unlicensed. Another copy of
this is also present in coreboot in the deprecated console/btext code.
The vga console code has been cleaned up, but it still has some TODO's left
open, but that's for when i finally have found the remaining issue with the
epia-m. Right now, it is important to get parts of my work out already and to
make the remainder managable again.
Signed-off-by: Luc Verhaegen <libv@skynet.be>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4321 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
the only selfboot user in CBFS.
This way, CBFS can be used without importing selfboot.c, as long as
no payloads are loaded.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4304 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Use that to fix selfboot with compressed payloads.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4281 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
I didn't try to remove "defined but not used" warnings because there are too
many ifdefs to be sure I wouldn't break something.
For shadowed variable declarations I renamed the inner-most variable.
The one in src/pc80/keyboard.c might need help. I didn't change the
functionality but it looks like a bug.
I boot tested it on s2892 and abuild tested it.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4240 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
* Make functions out of the accessor macros in mc146818rtc.c
* don't hide reserved cmos entries from coreboot, only from the user.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4170 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- fix up debug messages of usb debug console
(trivial)
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4162 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4152 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4126 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4125 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This also has the config tool changes in v2/util.
Rename romfs.[ch]->cbfs.[ch] and sed romfs->cbfs romtool->cbfstool ROMFS->CBFS
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4113 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Some changes for option roms:
- don't make users pick the name. Names for option roms are in the v3-defined
format of pci%04x,%04x.rom with the vendor and device id filling in the
%04x.
- users pass in vendor and device id.
- users pass in a dest. If the dest is 0, the address of the ROM image in
FLASH is returned. If the address is non-zero, then the decmpressor is called,
and it will make sure the ROM image is copied to the destination (even
in the uncompressed case).
And some type and print cleanup.
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4060 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4044 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
be used unconditionally, and the names don't hurt.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4042 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Some bootloaders seem to overwrite memory starting at 0x600, thus destroying
the coreboot table integrity, rendering the table useless.
By moving the table to the high tables area (if it's activated), this problem
is fixed.
In order to move the table, a 40 bytes mini coreboot table with a single sub
table is placed at 0x500/0x530 that points to the real coreboot table. This is
comparable to the ACPI RSDT or the MP floating table.
This patch also adds "table forward" support to flashrom and nvramtool.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4011 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
code expecting too old binutils(?).
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4007 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Use the (almost) same strict CFLAGS in v2 that we use on v3. And fix a few
include files and missing prototypes. Also, fix up the Config-abuild.lb files
to properly work for cross compiling.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4000 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
horribly broken and thus never used by any platform. This needs to get
straightened out so current chipsets drivers can use the full feature set.
Create wrapper functions similar to the io pci config space ones.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3981 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
sense, too). Have one u64 instead of three.
In order to use the old bios emulator, you have to do nothing. (Default, if
CONFIG_PCI_ROM_RUN is enabled)
In order to use yabel in your target, you need to add the following lines to
your config:
uses CONFIG_PCI_OPTION_ROM_RUN_YABEL
default CONFIG_PCI_OPTION_ROM_RUN_YABEL=1
In order to use vm86 in your target, you need to add the following lines to
your config:
uses CONFIG_PCI_OPTION_ROM_RUN_VM86
default CONFIG_PCI_OPTION_ROM_RUN_VM86=1
Note: vm86 only works on platforms with _RAMBASE in the lower megabyte.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Joseph Smith <joe@settoplinux.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3965 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
a long time ago. This will make it easier to port v2 boards forward to v3 at
some point (and other things)
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3964 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
(in addition to their low locations)
This adds the kontron 986LCD-M and the i945 as a sample.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3960 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Bellongs to r3947
Following patch adds dynamically generated P-States infrastructure as well as
M2V-MX SE as example how to do that. It is based on AMD code and mine code for
ACPI generation.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3948 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
hence I consider it trivial in this case). This does not include the Yabel
work.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3880 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
this type of checking in the v3 code since ages, but v2 will happily
compile any code with bogus printk format strings and/or parameters.
This can cause real bugs and at least needs to emit a warning, if not
an
error. Go with a warning for now since most of the flagged format
strings are wrong but harmless in a 32-bit x86 environment.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3872 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The FADT bootarch flags
Blacklists MSI for this chipset (maybe not needed)
Adds modified amdk8_util.asl
Adds the SSDT table to chain of tables
Aligns the FACS correctly (this should be done for other boards)
Adds the _CRS method to Asus M2V-MX SE acpi DSDT.
Fixes the FACS table length.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3840 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
mainboard specific code. (And add a hook to allow other mainboards do
a similar thing if required)
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Ronald G Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3812 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Robert Millan <rmh@aybabtu.com>
Acked-by: Jordan Crouse <jordan@cosmicpneguin.net>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3745 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Build-tested with the kontron/986lcd-m target.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3705 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This includes an early SMI handler.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3701 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Build-tested with the AMD dbm690t board.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Marc Jones <marc.jones@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3655 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
All the PCIe slots are enabled in this patch except power management.
Signed-off-by: Michael Xie <Michael.Xie@amd.com>
Reviewed-by: Marc Jones <marc.jones@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3588 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
on mine desktop) except of reverting the small change introduced by Bari
(gpio/inta setup reg 0x5b). This should go for some board specific file. The
change would broke at least mine board. But seems to be needed for jakllsch.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Bari Ari <bari@onelabs.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3567 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Ed Swierk <eswierk@arastra.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3547 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
and renames some existing macros for clarity.
Signed-off-by: Ed Swierk <eswierk@arastra.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3536 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
CONFIG_AP_IN_SIPI_WAIT flag. Newer Intel CPUs need this to operate with
multiple cores.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3465 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-Off-By: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3396 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The V-link setup and HT bridge is redone, because VT8237A has it in another
device. So far following combination of chipsets should now work:
K8T890CE + VT8237R
K8M890(CE) + VT8237R
VIA PC1 brige moved to NB code (vt8237r_bridge.c -> k8t890_bridge.c) and
notes about K8M890 support were added.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3183 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
max width of the link and also it will take the frequency of K8 HT
already done coreboot (and checks if t can run on it).
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3169 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
code it should have contained.
This patch updates the PCI IDs for Intel 3100 devices.
Signed-off-by: Ed Swierk <eswierk@arastra.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3160 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
working for now, and more work is needed for it to be fully dynamic. However,
just about any 128MB-512MB DIMM should work.
Signed-off-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3113 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
LPC device of the MCP55 southbridge, thus enabling flashrom access to the SPI
interface of the IT8716 SIO chip.
Changes :
1) - increase MAX_RESOURCES to 24 in device.h -> this was needed because some
functions of a PNP device can have more than 12 resources (ex the GPIO function
of IT8716f), in which case one could have an "array overflow" inside the device
structure (yes gcc is stupid!..) and ultimately a disaster (fool pointer at
device init time..)
2) - define resource masks for the GPIO function in
src/superio/ite/it8716f/superio.c -> this is needed because otherwise the IO
ranges which are set into the LPC bridge of the SB are very strange (f.ex.:
0x800->0x7ff and so on..). Problem: the PNP_IO0 resource is not defined for the
GPIO function, thus we have to define a "fake" mask "{0,0}" to avoid mismatching
by the init code
3) - enable the flash SPI interface into
src/mainboard/gigabyte/m57sli/Config.lb (by enabling the corresponding resource
into the GPIO function). I know that this is problematic because not all m57sli
boards are SPI, but .. do anyone have a better idea how to handle this?..
Signed-off-by: Florentin Demetrescu <echelon@free.fr>
I (Ward) have verified your patch on a rev2 of this board (it works!) as well
as on a rev1 (plcc). It does not affect flashing on rev1 nor have any averse
side effects that I noticed, so I think this patch should go in.
Acked-by: Ward Vandewege <ward@gnu.org>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3088 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
for each output device we support, so the payload can figure out
where to find consoles that the user cares about.
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3081 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
about a serial port. If a port is defined in the board configuration,
add it to lbtable.
Signed-off-by: Patrick Georgi <patrick@georgi-clan.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3076 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Due to the automatic nature of this update, I am self-acking. It worked in
abuild.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3053 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
code is changed.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3052 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Removed local APIC INIT (don't worry the APIC and AP are still initialized).
The local APIC INIT seemed to be the incorrect thing to do to stop an AP.
The Intel Multiprocessor specification indicated that a vector should be set
and a START should happen following an INIT. Then AP will execute the
instructions pointed to by the vector. There is no vector or start in
stop_this_cpu(). This seems to put the AP in an in-between state. In the case
of Barcelona the AP's MSRs and PCI register are not accessible by the hardware
debugger.
The better solution seems to be to just put the AP in a hlt and allow the AP
to go into C1. Then APIC managing software running on the BSP can program the
AP as needed.
Signed-off-by: Marc Jones <marc.jones@amd.com>
Reviewed-by: Jordan Crouse <jordan.crouse@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3017 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
These are the core files for HyperTransport, DDR2 Memory, and multi-core initialization.
Signed-off-by: Marc Jones <marc.jones@amd.com>
Reviewed-by: Jordan Crouse <jordan.crouse@amd.com>
Acked-by: Myles Watson <myles@pel.cs.byu.edu>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3014 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
ARRAY_SIZE() can be used on ROMCC-dependent systems. Also adds stdlib.h
to vt8237r_early_smbus.c, so it'll build on those systems.
Signed-off-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2949 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
(ICH/ICH0 up to the ICH9 family) in preparation for further
code improvements for the i82801xx southbridge code.
Small fixes in the 6300ESB PCI IDs.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2947 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
ICH5/ICH5R (more to follow) in preparation of further 82801xx improvements.
Use human-readable names for the PCI ID #defines.
Rename *_ISA to *_LPC as per datasheet.
The 82801DBM only has 3 (not 4) USB devices, looks like a copy-paste error.
The fixes in southbridge code are only to keep the build working for now,
any real improvements will only go into the 82801xx code in future.
This is abuild-tested so it shouldn't break anything.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2938 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
the Jetway J7F2 patch that should be coming soon, and also moves most
defines into vt8237r.h. I've changed some of the values from u32 to u8,
because that's all they should ever need to be. Also includes
doxygenized comments!
Signed-off-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2937 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2. Rename sisnb.c to sis761.c
3. Delete many mis-definition for sis device in
src/include/device/pci_ids.h
4. Trim trailing spaces for all files
Signed-off-by: Morgan Tsai <my_tsai@sis.com>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2931 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: <corey.osgood@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2907 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
In a mainboard's Config.lb file you can configure whether the primary
and/or secondary IDE interfaces shall be enabled.
Also, various fixups in the rest of the southbridge code, most notably
the early SMBus code, plus some documentation improvements.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Corey Osgood <corey_osgood@verizon.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2703 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2658 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2656 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Geode changes.
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2632 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
AMD GX and LX processors. This aguments the previous code, which was
very specific to the OLPC platform with general purpose support and
better integration with the VSA and CPUs.
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2631 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2628 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The following original authors agreed to the license:
- Ronald G. Minnich <rminnich@gmail.com>
- Indrek Kruusa <indrek.kruusa@artecdesign.ee>
- Stefan Reinauer <stepan@coresystems.de>
- Andrei Birjukov <andrei.birjukov@artecdesign.ee>
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2625 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Yinghai Lu <yinghai.lu at amd.com>
Signed-off-by: Ed Swierk <eswierk at arastra.com>
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Ward Vandewege <ward at gnu.org>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2589 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Uwe's version of yh_rest_of_patch.patch (13.02.07 - [PATCH]
Rest of huge MCP55 patch).
I dropped a lot of stuff, like broken indenting, removed copyright messages,
and this printk_ram_* stuff (what the heck is this supposed to be)
This codebase is really a mess. Further tarball contributions without a
_CLEANED UP_ patch will be denied, especially if they are not from an up to
date svn tree.
Signed-off-by: Yinghai Lu <yinghai.lu@amd.com>
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2563 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
won't compile), and breaks an unnecessary dependency on the usbdebug
code.
Signed-off-by: Ed Swierk <eswierk@arastra.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2543 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
* Added information on the relevant datasheet(s) and where to get them.
* Added missing #defines for some other config bytes.
* Documented all config bytes a bit better.
* Renamed some #defines to hopefully make their names clearer.
(closes#38)
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2506 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
add devices for the lx and artecgroup/dbe61
point artecgroup at cs5536_lx as it is so different.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2420 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Indrek Kruusa
Approved-by: Ronald G. Minnich
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2412 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
USB P4 is disabled by default and we need to setup the mux bits proper
to make it work. This is the frame work for that. All thats needed
is the right address values
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2387 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
here's a patch which replaces all DOS newlines with Unix newlines, and
removes some useless $Rev$, $Id$, and $Header$ tags.
(part 1)
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2385 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
* src/cpu/amd/model_lx/model_lx_init.c
L2 cache initialization removed (moved to northbridge.c)
* src/include/cpu/amd/lxdef.h
more checked values
* src/northbridge/amd/lx/northbridge.c
L2 cache initialization added
cpubug() commented out
* src/northbridge/amd/lx/raminit.c
empty function sdram_set_registers() is in use, don't remove
* src/mainboard/artecgroup/dbe61/Config.lb
irqmap changes
* src/mainboard/artecgroup/dbe61/irq_tables.c
tentative changes to irq table (currently not in use)
* src/mainboard/artecgroup/dbe61/mainboard.c
irq assigned manually to NIC
* src/mainboard/artecgroup/dbe61/Options.lb
gcc 4.0 is OK
* targets/artecgroup/dbe61/Config.lb
64K for VSA is OK at moment
Signed-off-by: Indrek Kruusa <indrek.kruusa@artecdesign.ee>
Signed-off-by: Andrei Birjukov <andrei.birjukov@artecdesign.ee>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2360 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
for L2 cache and fixes wrong P2D defines.
This also patch adds L2 cache initialization for Geode LX CPU.
Signed-off-by: Indrek Kruusa <indrek.kruusa@artecdesign.ee>
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2355 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
There is one global change to pci_ids.h. The rest are changes for LX. I
ran abuild and it is ok. Not all artec design changes are included as
some of them would adversely affect other mainboards. Indrek will need
to test.
Signed-off-by: Ron Minnich
Signed-off-by: Indrek Kruusa, indrek.kruusa@artecdesign.ee, artec
design.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2350 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
disabled.
cs5536: add new entires for SB control etc.
cs5536.c: chip_enabled function moved to chip_init, so it only gets run
once.
IRQ setup improved
gx2def.h: new defines added
vr.h: new file, with new def's for virtual register control.
mainboard config.lb: new entries added for nb and sb control.
chipsetinit.c: new controls added -- I forget all the details :-)
grphinit.c: new function added
northbridge.c: new IRQ control added. FlashChipSetup added, controlled
by chip info setupflash struct member. Currently, if enabled, this hangs
OLPC in linux PCI scan.
chip.h: new struct members added for unwanted device enable, flash setup
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2345 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Add cpureginit.c
added called to cpureginit to model_gx2_init.c
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2248 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
msr set in northbridge that conflicted with the cpubug support.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2218 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
store every HT device unit id base and pass those info to acpi
https://openbios.org/roundup/linuxbios/issue46
Note: This version drops the two scripts a and c and creates the dsdt on
the fly from Config.lb using makerule
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2134 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
a. apic id liftting to way that kernel like and let bsp
to stay with 0
b. hw memhole: solve if hole_startk == some node
basek
This, together with the previous one will break most of
the tree, but Yinghai Lu is really good
at fixing things, so...
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2116 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- In addition:
modified apic_id lifting to always lift all CPUs. This may cause problems with older kernels.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2068 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Special version for HDAMA rev G with 33Mhz test and reboot out.
- Support for CPU rev E, dual core, memory hoisting,
- corrected an SST flashing problem. Kernel bug work around (NUMA)
- added a Kernel bug work around for assigning CPU's to memory.
r2@gog: svnadmin | 2005-08-03 08:47:54 -0600
Create local LNXI branch
r1110@gog: jschildt | 2005-08-09 10:35:51 -0600
- Merge from Tom Zimmerman's additions to the hdama code for dual core
and 33Mhz fix.
r1111@gog: jschildt | 2005-08-09 11:07:11 -0600
Stable Release tag for HDAMA-1.1.8.10 and HDAMA-1.1.8.10LANL
r1112@gog: jschildt | 2005-08-09 15:09:32 -0600
- temporarily removing hdama tag to update to public repository. Will
reset tag after update.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2004 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
1. x86_setup_mtrr take address bit.
2. generic ht, pcix, pcie beidge...
3. scan bus and reset_bus
4. ht read ctrl to decide if the ht chain
is ready
5. Intel e7520 and e7525 support
6. new ich5r support
7. intel sb 6300 support.
yhlu patch
1. split x86_setup_mtrrs to fixed and var
2. if (resource->flags & IORESOURCE_FIXED ) return; in device.c pick_largest_resource
3. in_conherent.c K8_SCAN_PCI_BUS
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1982 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Creator: Yinghai Lu <yhlu@tyan.com>
cache_as_ram for AMD and some intel
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1967 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Creator: Yinghai Lu <yhlu@tyan.com>
AMD D0/E0 Opteron new mem mapping support, AMD E Opteron mem hole support,AMD K8 Four Ranks DIMM support
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1950 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Creator: Hamish Guthrie <hamish@prodigi.ch>
Added NSC pc97317 super-io and added fill character option to config/Options.lb to speed up flash programming
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1945 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
will generate the struct lb_memory_range the same.
- Add a few pci_ids.
- Small readabiltiy clean ups to debug_dev
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1818 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- The sandpointx3+altimus has been consolidated into one directory for now.
- Added support for having different versions of the pci access functions
on a per bus basis if needed.
Hopefully I have not broken something inadvertently.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1786 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Set adl855pc ROM_SIZE to 1M
Other minor debug prints until we get this fixed.
We're almost as far along as we were before the Change :-)
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1780 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
crt0.S.lb: Modified so that it is safe to include console.inc
console.c: Added print_debug_ and frieds which are non inline variants of the normal console functions
div64.h: Only include limits.h if ULONG_MAX is not defined and define ULONG_MAX on ppc
socket_754/Config.lb Conditionally set config chip.h
socket_940.c We don't need and #if CONFIG_CHIP_NAME we won't be linked in if there are no references.
slot_2/chip.h: The operations struct need to be spelled cpu_intelt_slot_2_ops
slot_2/slot2.c: The same spelling fix
socket_mPGA603/chip.h: again
socket_mPGA603/socket_mPGA603_400Mhz.c: and again
socket_mPGA604_533Mhz/Config.lb: Conditionally defing CONFIG_CHIP_NAME
socket_mPGA604_800Mhz/chip.h: Another spelling fix
socket_mPGA604_800Mhz.c and again
via/model_centaur/model_centaur_init.c: It's not an intel CPU so don't worry about Intel microcode uptdates
earlymtrr.c: Remove work around for older versions of romcc
pci_ids.h: More ids.
malloc.c: We don't need string.h any longer
uart8250.c: Be consistent when delcaring functions static inline
arima/hdama/mptable.c: Cleanup to be a little more consistent
amdk8/coherent_ht.c:
- Talk about nodes not cpus (In preparation for dual cores)
- Remove clear_temp_row (as it is no longer needed)
- Demoted the failure messages to spew.
- Modified to gracefully handle failure (It should work now if cpus are removed)
- Handle the non-SMP case in verify_mp_capabilities
- Add clear_dead_routes which replaces clear_temp_row and does more
- Reorganize setup_coherent_ht_domain to cleanly handle failure.
- incoherent_ht.c: Clean up the indenation a little.
i8259.c: remove blank lines at the start of the file.
keyboard.c: Make pc_keyboard_init static
ramtest.c: Add a print out limiter, and cleanup the printout a little.
amd8111/Config.lb: Mention amd8111_smbus.c
amd8111_usb.c: Call the structure usb_ops not smbus_ops.
NSC/pc97307/chip.h: Fix spelling issue
pc97307/superio.c: Use &ops no &pnp_ops.
w83627hf/suerio.c: ditto
w83627thf/suerio.c: ditto
buildrom.c: Use braces around the body of a for loop. It's more maintainable.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1778 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This file died with the last round of cpu restructuring I just missed it earlier.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1775 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Move pci_set_method out of hardwaremain.c
- Re-add debugging name field but only include the CONFIG_CHIP_NAME is
enabled. All instances are now wrapped in CHIP_NAME
- Many minor cleanups so most ports build.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1737 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
ram linuxbios_ram instead of linuxbios_c and linuxbios_payload...
- Reordered the linker sections so the LinuxBIOS fallback image can take more the 64KiB on x86
- ROM_IMAGE_SIZE now will work when it is specified as larger than 64KiB.
- Tweaked the reset16.inc and reset16.lds to move the sanity check to see if everything will work.
- Start using romcc's built in preprocessor (This will simplify header compiler checks)
- Add helper functions for examining all of the resources
- Remove debug strings from chip.h
- Add llshell to src/arch/i386/llshell (Sometime later I can try it...)
- Add the ability to catch exceptions on x86
- Add gdb_stub support to x86
- Removed old cpu options
- Added an option so we can detect movnti support
- Remove some duplicate definitions from pci_ids.h
- Remove the 64bit resource code in amdk8/northbridge.c in preparation for making it generic
- Minor romcc bug fixes
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1727 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- mem.h and sizeram.h and all includes killed because the are no longer needed.
- linuxbios_table.c updated to directly look at the device tree for occupied memory areas.
- first very incomplete stab a converting the ppc code to work with the dynamic device tree
- Ignore resources before we have read them from devices, (if the device is disabled ignore it's resources).
- First stab at Pentium-M support
- add part/init_timer.h making init_timer conditional until there is a better way of handling it.
- Converted all of the x86 sizeram to northbridge set_resources functions.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1722 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Rename chip_config chip_operations throughout the tree
- Fix Config.lb on most of the Opteron Ports
- Fix the amd 8000 chipset support for setting the subsystem vendor and device ids
- Add detection of devices that are on the motherboard (i.e. In Config.lb)
- Baby step in getting the resource limit handling correct, Ignore fixed resources
- Only call enable_childrens_resources on devices we know will have children
For some busses like i2c it is non-sense and we don't want it.
- Set the resource limits for pnp devices resources.
- Improve the resource size detection for pnp devices.
- Added a configuration register to amd8111_ide.c so we can enable/disable individual ide channels
- Added a header file to hold the prototype of isa_dma_init
- Fixed most of the superio chips so the should work now, the via superio pci device is the exception.
- The code compiles and runs so it is time for me to go to bed.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1698 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Fix the hdama Config.lb to not longer use the link keywords oops,
and instead to have it nest everything properly.
- Update config.g to not support the link keyword
- update config.g to not support northbridge/southbridge/cpu/pmc noise words
we can just use chip now.
- Remove old link handling from the code
- Detect and handle duplicate paths so we generate one device with multiple links
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1685 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Reworked pnp superio device support. Now complete superio support is less than 100 lines.
- Added support for hard coding resource assignments in Config.lb
- Minor bug fixes to romcc
- Initial support for catching the x86 processor BIST error codes. I've only seen
this trigger once in production during a very suspcious reset but...
- added raminit_test to test the code paths in raminit.c for the Opteron
- Removed the IORESOURCE_SET bit and added IORESOURCE_ASSIGNED and IORESOURCE_STORED
so we can tell what we have really done.
- Added generic AGP/IOMMU setting code to x86
- Added an implementation of memmove and removed reserved identifiers from memcpy
- Added minimal support for booting on pre b3 stepping K8 cores
- Moved the checksum on amd8111 boards because our default location was on top of
extended RTC registers
- On the Hdama added support for enabling i2c hub so we can get at the temperature
sensors. Not that i2c bus was implemented well enough to make that useful.
- Redid the Opteron port so we should only need one reset and most of memory initialization
is done in cpu_fixup. This is much, much faster.
- Attempted to make the VGA IO region assigment work. The code seems to work now...
- Redid the error handling in amdk8/raminit.c to distinguish between a bad value
and a smbus error, and moved memory clearing out to cpufixup.
- Removed CONFIG_KEYBOARD as it was useless. See pc87360/superio.c for how to
setup a legacy keyboard properly.
- Reworked the register values for standard hardware, moving the defintions from
chip.h into the headers of the initialization routines. This is much saner
and is actually implemented.
- Made the hdama port an under clockers BIOS. I debuged so many interesting problems.
- On amd8111_lpc added setup of architectural/legacy hardware
- Enabled PCI error reporting as much as possible.
- Enhanded build_opt_tbl to generate a header of the cmos option locations so
that romcc compiled code can query the cmos options.
- In romcc gracefully handle function names that degenerate into function pointers
- Bumped the version to 1.1.6 as we are getting closer to 2.0
TODO finish optimizing the HT links of non dual boards
TODO make all Opteron board work again
TODO convert all superio devices to use the new helpers
TODO convert the via/epia to freebios2 conventions
TODO cpu fixup/setup by cpu type
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1390 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Support for compiling romcc on non x86 platforms
- new romc options -msse and -mmmx for specifying extra registers to use
- Bug fixes to device the device disable/enable framework and an amd8111 implementation
- Move the link specification to the chip specification instead of the path
- Allow specifying devices with internal bridges.
- Initial via epia support
- Opteron errata fixes
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1200 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Major restructuring of hypertransport handling.
Major rewerite of superio/NSC/pc87360 as a proof of concept for handling superio resources dynamically
Updates to hard_reset handling when resetting because of the need to change hypertransport link
speeds and widths.
(a) No longer assume the boot is good just because we get to a hard reset point.
(b) Set a flag to indicate that the BIOS triggered the reset so we don't decrement the
boot counter.
Updates to arima/hdama mptable so it tracks the new bus numbers
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1097 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
* subtractive resources
* merging with the static device tree
* more device types than just pci
- The piece to watch out for is the new enable_resources method that was needed in all of the drivers
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1096 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This allows generic code to reset the box.
- Update the hypertransport code to automatically calculate link
widths and freequencies, and to call hard_reset if neecessary for
the changes to go into effect.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1094 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
for paths
- Renamed some configuration variables
SMP -> CONFIG_SMP
MAX_CPUS -> CONFIG_MAX_CPUS
MAX_PHYSICAL_CPUS -> CONFIG_MAX_PHYSICAL_CPUS
- Removed some dead configuration variables
MAX_CPUS -> CONFIG_MAX_CPUS
MAX_PHYSICAL_CPUS -> CONFIG_MAX_PHYSICAL_CPUS
SMP -> CONFIG_SMP
FINAL_MAINBOARD_FIXUP
SIO_BASE
SIO_SYSTEM_CLK_INPUT
NO_KEYBOARD
USE_NORMAL_IMAGE
SERIAL_CONSOLE
USE_ELF_BOOT
ENABLE_FIXED_AND_VARIABLE_MTRRS
START_CPU_SEG
DISABLE_WATCHDOG
ENABLE_IOMMU
AMD8111_DEV
- Removed some assembly files that are no longer needed
killed src/southbridge/amd/amd8111/smbus.inc
killed src/southbrideg/amd/amd8111/cmos_boot_failover.inc
killed src/ram/ramtest.inc
- Updates to config.g so that it works more reliably and has initial support
for paths
- Renamed some configuration variables
SMP -> CONFIG_SMP
MAX_CPUS -> CONFIG_MAX_CPUS
MAX_PHYSICAL_CPUS -> CONFIG_MAX_PHYSICAL_CPUS
- Removed some dead configuration variables
MAX_CPUS -> CONFIG_MAX_CPUS
MAX_PHYSICAL_CPUS -> CONFIG_MAX_PHYSICAL_CPUS
SMP -> CONFIG_SMP
FINAL_MAINBOARD_FIXUP
SIO_BASE
SIO_SYSTEM_CLK_INPUT
NO_KEYBOARD
USE_NORMAL_IMAGE
SERIAL_CONSOLE
USE_ELF_BOOT
ENABLE_FIXED_AND_VARIABLE_MTRRS
START_CPU_SEG
DISABLE_WATCHDOG
ENABLE_IOMMU
AMD8111_DEV
- Removed some assembly files that are no longer needed
killed src/southbridge/amd/amd8111/smbus.inc
killed src/southbrideg/amd/amd8111/cmos_boot_failover.inc
killed src/ram/ramtest.inc
killed src/sdram/generic_dump_spd.inc
killed src/sdram/generic_dump_spd.inc
- Updated the arima/hdama to build with the new configuration system
- Updated config.g to list all of the variables with make echo
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1093 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- SMP cleanups (remove SMP only use CONFIG_SMP)
- Minor tweaks to romcc to keep it from taking forever compiling
- failover fixes
- Get a good implementation of k8_cpufixup and sizeram for the opteron
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@998 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Changes to allow more code to be compiled both ways
- Working SMP support
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@987 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Add initial support for the amd8131
- Update the mptable to something possible
- hdama/Config add the amd8131 southbridge
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@968 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Update apic.h to include the APIC_TASK_PRI register definition
- Update mptable.c to have a reasonable board OEM and productid
- Additional testfiles for romcc.
- Split out auto.c and early failover.c moving their generic bits elsewere
- Enable cache of the rom
- Fixes to amd8111_lpc.c so that we successfully setup virtual wire mode on the ioapic
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@880 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Aaron Durbin