ppc port, some ambiguous use of CONFIG_IDE and an unused ide driver (we dropped
the filesystems already to be used with it) (somewhat trivial)
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4828 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Change HAVE_FAN_CTL to be specific to the SuperIO that supports it.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4809 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
VGA ROM can not run. After make, run
> ./cbfs/cbfstool ./coreboot.rom add ../vga_bios.rom pci1002,791f.rom optionrom
to make the final image with vga bios.
The macro vga_rom_address is out-of-date when CBFS starts play its role. it also should
be eliminated from rs690/chip.h as below. But it will cause building error on other board, which I
cant make test on.
## Index: src/southbridge/amd/rs690/chip.h
## ===================================================================
## --- src/southbridge/amd/rs690/chip.h (revision 4782)
## +++ src/southbridge/amd/rs690/chip.h (working copy)
## @@ -23,7 +23,6 @@
## /* Member variables are defined in Config.lb. */
## struct southbridge_amd_rs690_config
## {
## - u32 vga_rom_address; /* The location that the VGA rom has been appened. */
## u8 gpp_configuration; /* The configuration of General Purpose Port, A/B/C/D/E. */
## u8 port_enable; /* Which port is enabled? GFX(2,3), GPP(4,5,6,7) */
## u8 gfx_dev2_dev3; /* for GFX Core initialization REFCLK_SEL */
##
Don't apply above patch about rs690/chip.h before every board has been fixed.
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4783 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
to build, but by default all the tables that are available are built.
Make PIRQ table build for qemu.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4778 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Reset the s2891 so the HT speed gets updated.
Remove some PANTA comments.
Add SATA init from non-CAR version.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4771 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
There is an i2c mux out there. We found it using a user level program
that, as usual, began by inverting all gpios until we found out
what we needed to know. In the end, we just set up the GPIOs as
the factory bios does.
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4755 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Use "default n" for all components that shall be "select"ed.
- Use "0x0" instead of "0" for hex variables for clarity and to reduce
the risk of people passing integer instead of hex values to such variables.
- Add TODO comments for boards that have irq_tables.c but don' set
CONFIG_HAVE_PIRQ_TABLE = 1. Someone with the hardware should test enabling.
- ASUS M2V-MX SE doesn't have irq_tables.c so don't define
IRQ_SLOT_COUNT in its Kconfig file.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4749 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4748 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
their own vgabios.c
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4744 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4731 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
in very early stages, otherwise the boot may hang like this because
the CBFS headers cannot be found/accessed:
Uncompressing coreboot to RAM.
Jumping to image.
Check CBFS header at fffedfe0
magic is ffffffff
ERROR: No valid CBFS header found!
CBFS: Could not find file fallback/coreboot_ram
Jumping to image.
This patch enables full ROM access on all 440BX boards right after the
serial init (and before CBFS headers are parsed).
Build-tested and runtime-tested on ASUS P2B-F.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4721 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Both were only really used in pre-cbfs, as the payload's size isn't
relevant for the build process anymore.
Various calculations in {no,}failovercalculation.lb are adapted
accordingly.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4720 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4719 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- northbridges are done
- southbridges are done
- Intel CPUs are done, with a design that the board only has to specify
the socket it has, and the CPUs are pulled in automatically. There is
some more cleanup possible in that area, but I'll do that later
- a couple more mainboards compile:
- intel/eagleheights
- intel/jarrell
- intel/mtarvon
- intel/truxton
- intel/xe7501devkit
- sunw/ultra40
- supermicro/h8dme
- tyan/s2850
- tyan/s2875
- via/epia
- via/epia-cn
- via/epia-m
- via/epia-m700
- via/epia-n
- via/pc2500e
(PPC not considered, probably overlooked something)
All of them only _build_, but some options are probably completely
wrong. To be fixed later
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4673 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
src/cpu/amd/socket_F/Kconfig: Remove second occurrence of CPU_SOCKET_TYPE.
src/mainboard/amd/serengeti_cheetah/Kconfig: Add HT_CHAIN_UNITID_BASE here, since it is board specific.
src/mainboard/tyan/s289X/Kconfig: Fix typo and change APIC_ID_OFFSET to match old config.
src/devices/Kconfig: Change default value of *_PLUGIN_SUPPORT to match old config.
src/southbridge/amd/amd8131/Makefile.inc: Remove check since it was a typo, and the correct variable is checked in the parent directory.
src/Makefile:Use devicetree.cb instead of Config.lb to generate static.c.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4657 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
kconfig_s2892.dif: Add support for Tyan s2891, s2892, and s2895 to Kconfig.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4656 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
write. It boots the SB/NB V-link performance to full duplex 533MB/s. (in fact x2
for FDX)
The default was 266MB/s but half duplex only. If you encourage any stability
issues we need to look into fine tuning the bus. The values are VIA recommended.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4625 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
tested. I also addressed questions raised by Uwe:
TSC_X86RDTSC_CALIBRATE_WITH_TIMER2
UDELAY_TSC
Are now defined as booleans in src/cpu/x86/Kconfig and can be selected in
the mainboard Kconfig. The remaining question of Uwe's is a deeper
problem:
---
We'll have to check if this works. From a quick glance
the Rumba does not have the mmx related lines (which _are_ in
Makefile.romccboard.inc, though):
crt0-y += ../../../../src/cpu/x86/fpu/enable_fpu.inc
crt0-y += ../../../../src/cpu/x86/mmx/enable_mmx.inc
crt0-y += auto.inc
crt0-y += ../../../../src/cpu/x86/mmx/disable_mmx.inc
---
We're going to need a whole variant of this standard mainboard OR
we're going to have to make (some) of the unconditional includes above
conditional.
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4618 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This patch tries to improve the pcie portA configuration.
The Matrox G550e PCIe gfx card shipped along with the dev board is supported.
Signed-off-by: Arnaud Maye <arnaud.maye@4dsp.com>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4615 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4613 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
It also brings in the vsm from v3, which was a much cleaner cut.
Over time, I hope to bring all the code back from v3. I have
some rumbas at home and want to use them.
I have a patch which comes in next that makes the rumba build.
Note that I am holding the src/*/amd/Kconfig patch until these get merged.
These have no impact on the current system.
Note that this is not complete but I want to fill in the blanks bit
by bit.
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4611 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The SB600 SATA code printed that two BARs had the same address because
it didn't mask the correct number of bits in the BAR.
Functionality was not affected, but the debug output was incorrect.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Zheng Bao <zheng.bao@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4591 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
monitors.
Signed-off-by: Libra Li <libra.li@technexion.com>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4585 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Whitespace fixes, remove trailing whitespace, use TABs for identation
(except in Kconfig "help" lines, which start with one TAB and two spaces
as per Linux kernel style)
- Kconfig: Standardize on 'bool' (not 'boolean').
- s/lar/cbfs/ in one Kconfig help string.
- Reword various Kconfig menu entries for a more usable and consistent menu.
- Fix incorrect comment of NO_RUN in devices/Kconfig.
- superio/serverengines/Kconfig: Incorrect config name.
- superio/Makefile.inc: s/serverengine/serverengines/.
- superio/intel/Kconfig: s/SUPERIO_FINTEK_I3100/SUPERIO_INTEL_I3100/.
- mainboard/via/vt8454c/Kconfig: Fix copy-paste error in help string.
- mainboard/via/epia-n/Kconfig: Fix "bool" menu text.
- console/Kconfig: Don't mention defaults in the menu string, kconfig
already displays them anyway.
- Kill "Drivers" menu for now, it only confuses users as long as it's emtpy.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4567 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Note the makefile.inc may be out of date given the new commits of code
today, but this is what was signed off ...
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4551 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Tested on Via EPIA-NL8000EG with FILO payload booting FC9 (2.6.25
kernel) from SATA HDD.
ACPI is working for PCI interrupt routing, some memory stuff and
Soft-Off.
USB/SATA Working
VGA Console Working
X Working via Onboard AGP
Removed dsdt.c, fixed some whitespace.
Signed-off-by: Jon Harrison <bothlyn@blueyonder.co.uk>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4549 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4537 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4535 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Works on Kontron, qemu, and serengeti.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
tested on abuild only.
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4534 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Add initialisation for the VIA Chrome 9 IGP on the k8m890 through native code
and through the general vga infrastructure i committed a month or two ago.
Add videoram_size option for k8m890 and the Asus M2V-MX SE.
Now the Asus M2V-MX SE will magically come up with a working standard VGA
80x25 textmode.
Many thanks to the people who worked hard on the Asus M2V-MX SE, and all
of its components; this vga bringup was a breeze thanks to your hard work
for this excellently supported board. And separate thanks to Rudolf Marek
for spurring me on and for providing a register dump.
Signed-off-by: Luc Verhaegen <libv@skynet.be>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4465 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- code restructuring (move ich7 out of i945)
- ACPI fixes
- major SMI handler updates
- make sure SMBus lives where we expect it
- try to get usb debug working
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4456 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- drop duplicate udelay function
- simplify code flow
- some cosmetics on comments
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4445 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
those symbols were left alone before, after this, they're
somewhat more in line with the rest of the tree.
Signed-off-by: Patrick Georgi <patrick.georgi@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4442 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
single core.
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4415 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Major changes:
1. Separate resource allocation into:
A. Read Resources
B. Avoid fixed resources (constrain limits)
C. Allocate resources
D. Set resources
Usage notes:
Resources which have IORESOURCE_FIXED set in the flags constrain the placement
of other resources. All fixed resources will end up outside (above or below)
the allocated resources.
Domains usually start with base = 0 and limit = 2^address_bits - 1.
I've added an IOAPIC to all platforms so that the old limit of 0xfec00000 is
still there for resources. Some platforms may want to change that, but I didn't
want to break anyone's board.
Resources are allocated in a single block for memory and another for I/O.
Currently the resource allocator doesn't support holes.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4394 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Jon Harrison <bothlyn@blueyonder.co.uk>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4389 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
It's basically done with the following script and some manual fixup:
VARS=`grep ^define src/config/Options.lb | cut -f2 -d\ | grep -v ^CONFIG | grep -v ^COREBOOT |grep -v ^CC`
for VAR in $VARS; do
find . -name .svn -prune -o -type f -exec perl -pi -e "s/(^|[^0-9a-zA-Z_]+)$VAR($|[^0-9a-zA-Z_]+)/\1CONFIG_$VAR\2/g" {} \;
done
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4381 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Add initial ACPI support for M57SLI.
Activates/Enables:
* native Coreboot ACPI for M57SLI
* Soft-Power-Off
* PowerNow!
* High Precision Event Timer
* Windows booting with ACPI support
Signed-off-by: Harald Gutmann <harald.gutmann@gmx.net>
Acked-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4364 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Any endless loop after die() can be eliminated.
Dereferencing a NULL pointer is bad. die() instead.
Replace endless loops with die().
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4340 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
starts to play its role. Then the system hangs at HDA init. I dont know what the
VC1 is. The RPR says "Optional Features (only needed if CMOS option is enabled)"
in 5.10.2. Before I know what it is, I think it is better to skip it.
Tested on dbm690t.
Add comment from Rudolf,
"
VC is virtual channel. Its used for isochronous transfer of data to sound card.
The virtual channel guarantee "on time" delivery. In other words it sets up a
channel for data to sound card, which means that that arrivs in time and there will
be no interuptions in audio stream.
http://www.microsoft.com/whdc/connect/pci/wlp_interrupt.mspx
"
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4339 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
1. In rs690_cmn.c, mask the lower 4 bits of the BAR3. No doubt, right?
2. In rs690_pcie.c,
(1) Obviously, the mask should be 0xF, and bit 19 should be set to 1 (in comment).
In rpr 5.10.2, step 2, step 2.1 & step 2.6
(2) The dynamic buffer allocation is enabled by setting bit 11 of PCIEIND: 0x20,
instead of PCIEIND_P: 0x20.
In rpr 5.10.2, step 5. Dynamic Slave CPL Buffer Allocation
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4336 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This reverts commit eb7bb49eb5b48c39baf7a256b7c74e23e3da5660.
Stepan pointed out that "s" means string, which makes the following statement
in this commit message invalid: "Since we either have reserved space (which
we shouldn't do anything with in these two functions), an enum or a
hexadecimal value, unsigned int seemed like the way to go."
Signed-off-by: Luc Verhaegen <libv@skynet.be>
Acked-by: Luc Verhaegen <libv@skynet.be>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4335 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
To ease some of my debugging pain on the unichrome, i decided i needed to
move FB size selection into cmos, so i could test a size and then reset it
to the default after loading this value so that the next reboot uses the
(working) default again. This meant implementing set_option in parallel to
get_option.
get_option was then found to have inversed argument ordering (like outb) and
passing char * and then depending on the cmos layout length, which made me
feel quite uncomfortable. Since we either have reserved space (which we
shouldn't do anything with in these two functions), an enum or a
hexadecimal value, unsigned int seemed like the way to go. So all users of
get_option now have their arguments inversed and switched from using ints
to unsigned ints now.
The way get_cmos_value was implemented forced us to not overlap byte and to
have multibyte values be byte aligned. This logic is now adapted to do a
full uint32_t read (when needed) at any offset and any length up to 32, and
the shifting all happens inside an uint32_t as well. set_cmos_value was
implemented similarly. Both routines have been extensively tested in a
quick separate little program as it is not easy to get this stuff right.
build_opt_tbl.c was altered to function correctly within these new
parameters. The enum value retrieval has been changed strol(..., NULL, 10)
to stroul(..., NULL, 0), so that we not only are able to use unsigned ints
now but so that we also interprete hex values correctly. The 32bit limit
gets imposed on all entries not marked reserved, an unused "user_data" field
that appeared in a lot of cmos.layouts has been changed to reserved as well.
Signed-off-by: Luc Verhaegen <libv@skynet.be>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4332 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
directory just with one common file.
Changes to FADT: move to rev4, fix the generic register descriptors, detect additional VT8237S features.
Change the compiler to CORE , its revision to 42.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4327 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Joseph Smith <joe@settoplinux.org>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4324 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
patch, just removes the warnings like
coreboot-v2/src/southbridge/intel/i82801xx/i82801xx_ac97.c:73: warning: initialization discards qualifiers from pointer target type
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4302 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
src/northbridge/intel/i440bx/ but not to
src/cpu/emulation/qemu-x86/northbridge.c
It also adds a driver for the ISA device that is found when using
0.9.1 If you look in a log without this patch you won't find the RTC
init lines.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4269 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Joseph Smith <joe@settoplinux.org>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4251 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Joseph Smith <joe@settoplinux.org>
Acked-by: Joseph Smith <joe@settoplinux.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4249 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
I didn't try to remove "defined but not used" warnings because there are too
many ifdefs to be sure I wouldn't break something.
For shadowed variable declarations I renamed the inner-most variable.
The one in src/pc80/keyboard.c might need help. I didn't change the
functionality but it looks like a bug.
I boot tested it on s2892 and abuild tested it.
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4240 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4108 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
part of this patch adds support for resume well NVRAM. In which DQS values are
stored.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4100 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
coreboot to 1MB and tries to cache whole range for XIP. The UMA part colide a
bit with the HAVE_HIGH_TABLES region. I solved that by relocation of the region.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4024 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Use the (almost) same strict CFLAGS in v2 that we use on v3. And fix a few
include files and missing prototypes. Also, fix up the Config-abuild.lb files
to properly work for cross compiling.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@4000 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3999 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
be required for a series of later patches. Roughly it contains:
* fixed SMBus driver (was not compiled in before)
* fixed S-ATA/P-ATA combination
* Added warnings to drivers being called with a NULL dev->chip_info
* Set subsystem ids for those boards that have none specified in Options.lb
* Fix license headers. The code was originally released under GPL v2 but
some files sneaked in with a v2 or later header.
* some attempts to fix azalia/Intel HDA.. not working yet
* clean up and fix pci bridge handling code
* Add Config based GPI handling to LPC driver
* Add HPET enable function
* Enable clock gating where appropriate
* first attempt at USB debug console support (not working yet)
* Add required options to kontron board
* many other minor changes
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3991 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
changes by file:
src/northbridge/amd/amdk8/northbridge.c:
Add high tables code ala Stefan's code for the i945.
src/southbridge/nvidia/ck804/ck804_lpc.c:
Enable High Precision Event Timers.
Add pm_base for ACPI.
src/southbridge/nvidia/ck804/ck804_fadt.c:
Since fadt is only dependent on the Southbridge, add it here.
src/southbridge/nvidia/ck804/Config.lb:
Compile in ck804_fadt.c
Signed-off-by: Myles Watson <mylesgw@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3988 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
a long time ago. This will make it easier to port v2 boards forward to v3 at
some point (and other things)
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3964 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- make uma_memory_base and uma_memory_size uint64_t as they may be 64bit BARs
on some platforms.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3949 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Reorder HDA (HD Audio) init:
The reordering was based on what order things happen in the BIOS
Developers guide, RPR, and SATA driver. I fixed the order of the devices
that didn't matter to clean up the change log.
1. Enable the Chip
2. Setup the SMBus registers
3. Setup the Device Registers
4. Look for Codec
5. Init Codec
The codec init was changed to match the description in the RRG pg 235.
Mem Reg: Base + 08h Bit 0. There were unneeded things happening.
Added 1ms delay to match the BKDG while waiting for BAR+0xe to set its
bits.
Signed-off-by: Dan Lykowski <lykowdk@gmail.com>
Tested on AMD DBM690T and AMD Pistachio by Maggie Li. Works.
Tested on Asus M2A-VM by Carl-Daniel Hailfinger. Improves the situation,
but some warnings remain.
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3930 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Maggie Li <maggie.li@amd.com>
Reviewed-by: Zheng Bao <Zheng.bao@amd.com>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3891 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3887 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- use new features of the ich7 update
- move rambase above 1M to avoid memory trashing through SMM relocation
- enable superio HWM
Update ICH7 driver
- minor smi cosmetics (in progress)
- add real ac97 driver
- add real azalia driver
- fix some interrupt issues
- fix some sata issues
- include Patrick's fix for _lpc.c
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Patrick Georgi <patrick.georgi@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3886 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
parts.
This should help to reduce the code duplication for Rudolf's K8/VIA SMM
implementation...
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Joseph Smith <joe@settoplinux.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3870 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
SATA port status kept returning 0x1: BAR5+po+28h
1h = Device presence detected but Phy communication not established
This patch adds logic to force 1.5g if the drive fails to communicate at 3.0g.
Signed-off-by: Dan Lykowski <lykowdk@gmail.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3864 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
is no longer 0xA0 or 0xB0. It simply assumes that will never happen.
My 500 GB Seagate Barracuda ST3500820AS triggers that corner case on the
first init after poweron.
The current code hangs forever with my drive. Fix this by rerunning the
init sequence after SATA_BAR0+6 is no longer 0xA0 or 0xB0.
Add support for SATA port 2-4 (Primary Slave, Secondary Master,
Secondary Slave).
If only the 2nd SATA port is connected and the hardware acts strangely
(contrary to documentation), it will print the error message below and
continue anyway. The official AMD asm code behaves the same way.
SATA port 0 status = 0
No Primary Master SATA drive on Slot0
SATA port 1 status = 23
0x6=7f, 0x7=7f
drive no longer selected after 0 ms, retrying init
[8 repetitions]
0x6=7f, 0x7=7f
drive no longer selected after 0 ms, retrying init
Primary Slave device is not ready after 10 tries
Activate and improve debug messages for SPEW log level.
Fix some comments.
New log messages look like this:
PCI: 00:12.0 init
sata_bar0=3020
sata_bar1=3060
sata_bar2=3030
sata_bar3=3070
sata_bar4=3000
sata_bar5=fc309000
SATA port 0 status = 23
0x6=a0, 0x7=80
drive detection not yet completed, waiting...
0x6=a0, 0x7=80
drive detection not yet completed, waiting...
[... 281 repetitions ...]
0x6=0, 0x7=50
drive no longer selected after 2820 ms, retrying init
drive detection done after 0 ms
Primary Master device is ready after 2 tries
SATA port 1 status = 23
drive detection done after 0 ms
Primary Slave device is ready after 1 tries
SATA port 2 status = 0
No Secondary Master SATA drive on Slot2
SATA port 3 status = 0
No Secondary Slave SATA drive on Slot3
With this patch, my Asus M2A-VM boots into Linux without problems.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Zheng Bao <zheng.bao@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3845 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The RS690 chipset has a problem where it will not work with 1 GHz HT
speed unless NB_CFG_Q_F1000_800 bit 0 is set.
Tested, works on my Asus M2A-VM with an 1 GHz HT capable processor.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Bao, Zheng says:
As a matter of fact, both 600Mhz and 1Ghz have their own specific
setting.
This patch has been tested on dbm690t which HT link works on 800Mhz.
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3839 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The device ID of 690G is 0x791E, while the ID of 690M and 690T is 0x791F
This fixes booting on 690G.
Signed-off-by: Zheng Bao <zheng.bao@amd.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3816 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
mainboard specific code. (And add a hook to allow other mainboards do
a similar thing if required)
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Ronald G Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3812 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
document verification against the data sheets.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Maggie Li <maggie.li@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3811 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
0xe4 and 0xe5 registers. I'm suspecting that the documentation may be wrong.
Furthermore this fix for powernow may not work on CPUs hit by errata #181.
Workaround should be implemented. The powernow may not work on pre-A2 revisions
of VT8237S silicon, revision reg is unknown.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3795 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Joe Bao <zheng.bao@amd.com>
Reviewed-by: Maggie Li <maggie.li@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3786 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Joe Bao <zheng.bao@amd.com>
Reviewed-by: Maggie Li <maggie.li@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Marc Jones <marcj303@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3785 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also, fix BIOS_CNTL, which is 0xdc on ICH7.
Build-tested with kontron/986lcd-m.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3733 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
ICH7 southbridge (but it might work with ICH4/ICH5 or so).
The ICH7 needs a different init code. Drop the non-working code for now.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3732 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
to only a set of reasonably similar ones, namely (for now) ICH0* - ICH6*,
and C-ICH.
All later ICH* southbridges (ICH7-ICH10) are _very_ different and were surely
not working with this driver anyway (and there's no chance to support
them reasonably with this driver without ending up in #ifdef hell).
ICH7 now has an extra driver in svn, whether ICH8-ICH10 are similar
enough to be supported by that ICH7 driver remains to be seen.
This patch was informally acked by Stefan Reinauer
<stepan@coresystems.de> on IRC.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3718 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Build-tested with the kontron/986lcd-m target.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3705 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This includes an early SMI handler.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3701 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Also, use more readable #defines instead of hardcoded config ports for
PM/PM2 related functions, and simplify them a bit.
Build-tested with the AMD dbm690t target.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Marc Jones <marc.jones@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3680 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
build. As far as I know, no C7 boards currently in the tree use SPI
flash.
Signed-off-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3665 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
called from one target and that target is compiled with GCC, make the
function dependent on GCC.
ROMCC also chokes on the ULL suffix for integer constants. Change the
affected ones to UL for ROMCC compiled code.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3664 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
is also visible to ROMCC and ROMCC doesn't understand that.
The fix is to use __attribute__((packed)) only for gcc compiled code.
This has been unfixed for too long. There are more problems remaining,
but at least this one is solvable easily.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3660 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Build-tested with the AMD dbm690t board.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Marc Jones <marc.jones@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3655 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Marc Jones <marcj.jones@amd.com>
Acked-by: Marc Jones <marcj.jones@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3643 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
We shouldn't assume the presence of a working HDA codec, so put in
a reasonable timeout of 50usecs (timeout value borrowed from the kernel).
This makes SimNow work, since apparently though the codec is
present in Simnow, it is non functional.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3640 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Marc Jones <marc.jones@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3636 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
certainly won't build -- that comes later. I am hoping to get some
eyeballs on it for simple errors.
rs690 is next.
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3630 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
code to use it. That makes the code more readable and also less
error-prone.
Abuild tested.
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3624 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Most of the functions in SB600 are enabled except power management.
Signed-off-by: Michael Xie <Michael.Xie@amd.com>
Reviewed-by: Marc Jones <marc.jones@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3589 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
All the PCIe slots are enabled in this patch except power management.
Signed-off-by: Michael Xie <Michael.Xie@amd.com>
Reviewed-by: Marc Jones <marc.jones@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3588 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
D1F0 bridge without activated I/O and MEM resources, otherwise it will hang
whole PCI bus.
U-boot is also disabling the IO/MEM decode when sizing the BARs, dont know why
does we not.
Second small change just changes a bit which controls the PSTATECTL logic.
Third change deals with the integrated VGA, which needs to be enabled early,
so the VGA_EN is set along the bridges, and PCI K8 resource maps are set
correctly. Finally the CPU accessible framebuffer is now disabled as it is not
needed.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3587 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
on mine desktop) except of reverting the small change introduced by Bari
(gpio/inta setup reg 0x5b). This should go for some board specific file. The
change would broke at least mine board. But seems to be needed for jakllsch.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Bari Ari <bari@onelabs.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3567 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
All devices work, no irq storms. Enjoy.
Signed-off-by: Bari Ari <bari@onelabs.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3556 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
and renames some existing macros for clarity.
Signed-off-by: Ed Swierk <eswierk@arastra.com>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3536 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
integrated LPC, SMBus, USB and SATA devices of the Intel EP80579
Integrated Processor.
Signed-off-by: Ed Swierk <eswierk@arastra.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3535 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Bari Ari <bari@onelabs.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3369 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
pci_write_config8.
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3282 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
for both serial ports, making it challenging to use COM2 for the early
console.
Enable the traditional I/O ranges 0x3f8 for COM1 and 0x2f8 for COM2.
Signed-off-by: Ed Swierk <eswierk@arastra.com>
Acked-by: Joseph Smith <joe@settoplinux.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3276 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
secondary controller was ok). There were two problems: the master sata
controller was not being initialized, and the irqs for the secondary ports on
both controllers were not being set in the mptable.
Thanks for Jonathan Kollasch for all the help figuring out the IRQ problem.
While all ports work reliably under a recent kernel (2.6.24), sata is about
half as fast as under the proprietary bios, according to bonnie++. That still
needs fixing...
Signed-off-by: Ward Vandewege <ward@gnu.org>
Acked-by: Myles Watson <mylesgw@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3253 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
It also keeps the boot processes from rebooting through out the coreboot process.
Signed-off-by: Joseph Smith <joe@smittys.pointclark.net>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3218 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
"off" in Config.lb should cause the PCI device not to respond to
configuration requests.
Replace the existing code that I naively copied from esb6300 with
something that actually works on the 3100.
Signed-off-by: Ed Swierk <eswierk@arastra.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3209 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Joseph Smith <joe@smittys.pointclark.net>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Ed Swierk <eswierk@arastra.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3208 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
There are no boards that use the i82801DB (ICH4). The code does NOT work.
Signed-off-by: Joseph Smith <joe@smittys.pointclark.net>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Ed Swierk <eswierk@arastra.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3206 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
pci_locate_device() to locate the SMBus controller and LPC bridge
devices on the PCI bus. Since these devices are always located at a
fixed PCI bus:device:function, the code can be simplified by
hardcoding the devices.
Signed-off-by: Ed Swierk <eswierk@arastra.com>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3205 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
the system automatically unless software resets the timer
periodically. The extra reboot extends boot time by several seconds.
The attached patch adds a function to the Intel 3100 southbridge code
that halts the TCO timer, thus preventing this extra reboot, and calls
the function early in the boot process on the Mt. Arvon board.
It also fixes a bug in the LPC device initialization -- the ACPI BAR
enable flag is bit 7, not bit 4.
Signed-off-by: Ed Swierk <eswierk@arastra.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3198 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
You can see this by executing commands like this:
grep -r pci_assign_irqs coreboot/src/*
This basically AMD/LX based boards: pcengines/alix1c,
digitallogic/msm800sev, artecgroup/dbe61, amd/norwich, amd/db800.
Also for AMD/GX1 based boards need a patch
[http://www.pengutronix.de/software/ptxdist/temporary-src/references/geode-5530.patch]
for the right IRQ setup.
AMD/GX1 based boards is: advantech/pcm-5820, asi/mb_5blmp, axus/tc320,
bcom/winnet100, eaglelion/5bcm, iei/nova4899r, iei/juki-511p.
I have two ideas.
1. Delete duplicate code from AMD/LX based boards.
2. Add IRQ routing for AMD/GX1 boards in coreboot.
The pirq.patch for IRQ routing logically consist from of two parts:
First part of pirq.patch independent from type chipsets and assign IRQ for
ever PCI device. It part based on AMD/LX write_pirq_routing_table() function.
Second part of pirq.patch depends of type chipset and set PIRQx lines
in interrupt router. This part supports only CS5530/5536 interrupt routers.
IRQ routing functionality is included through PIRQ_ROUTE in Config.lb.
Tested on iei/juki-511p(cs5530a), iei/pcisa-lx(cs5536) and also on
TeleVideo TC7020, see
http://www.coreboot.org/pipermail/coreboot/2007-December/027973.html.
Signed-off-by: Nikolay Petukhov <nikolay.petukhov@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3196 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The V-link setup and HT bridge is redone, because VT8237A has it in another
device. So far following combination of chipsets should now work:
K8T890CE + VT8237R
K8M890(CE) + VT8237R
VIA PC1 brige moved to NB code (vt8237r_bridge.c -> k8t890_bridge.c) and
notes about K8M890 support were added.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3183 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
max width of the link and also it will take the frequency of K8 HT
already done coreboot (and checks if t can run on it).
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3169 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
comments. Ripping out the ehci/uhci_init() code doesn't seem to have
done any harm, and I got rid of a bunch of unused junk in
i3100_smbus.h
I left the *_set_subsystem() arguments unsigned, as that's how the
function is declared in include/device/pci.h.
Signed-off-by: Ed Swierk <eswierk@arastra.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3157 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
flashes such as SST49LF080A: 1024K x8 (8 Mbit)
Tested on my system, the flash is found and if I use coreboot in second half it
works too.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3148 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
nVidia cards. The enable link should be enough, retrain is done there.
Tested on my system.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3147 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
a compiler warning.
Signed-off-by: Ronald Hoogenboom <hoogenboom30@zonnet.nl>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3115 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Don't enable pin0 for ioapic of io-4.
1. apic error in kernel for MB with mcp55+io55
2. some pcie-cards could have pci bridge there, so need to put entries
for device under them in mptable.
Signed-off-by: Yinghai Lu <yinghailu@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3112 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Due to the automatic nature of this update, I am self-acking. It worked in
abuild.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3053 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
code is changed.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3052 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Check that the SMBus controller is found and stop on an error.
Clean up and add additional path through the 8111 reset functions.
Signed-off-by: Marc Jones <marc.jones@amd.com>
Reviewed-by: Jordan Crouse <jordan.crouse@amd.com>
Acked-by: Myles Watson <myles@pel.cs.byu.edu>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@3015 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Implement ISA related support:
- Initialize the RTC
- Enable access to all BIOS regions (but _not_ write access to ROM)
- Enable ISA (not EIO) support
- Without the *_isa.c file, the Super I/O init is never performed
- Improve IDE support:
- Add config option to enable Ultra DMA/33 for each disk
- Add config option to enable legacy IDE port access
- Implement hard reset support
- Implement USB controller support
- Various code cleanups and improvements
The code partially supports southbridges other than the 82371EB (but
which are very similar), more complete support will follow.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2994 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Use 'static' where appropriate.
- Use 'const' where appropriate.
- Indentation fixes.
- Add comment wrt init code which is only valid for VT8237R.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2974 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Upon incoming SMAF message from CPU (C3 or FID/VID change), the SB will
assert SLP# which is connected to LDTSTOP_L on K8 CPUs. Question is for how
long. Imho for 100us. Which is more than plenty (2us required) I will try
to justify this once I know what bios to set in SB.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2965 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
it to 8X transfer rate (up to 1066 MB/s) similar code placed here would be
needed for VT8237A/S etc. Using VIA recommended values despite they are for
K8T890CF, this is K8T890CE (still dont know what is exactly different).
This patch enables the parity error reporting on V-Link, so it enables NMI
generation for the SERR# errors. The NMI may not be generated, maybe port
61h needs some tuning too.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2958 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
i82801xx code for the following parts:
- AC97 audio/modem
- Onboard network interface cards (NICs)
- USB 1.1 controllers
- SMBus controllers
Some other parts are still missing and will be added later.
Use PCI ID #defines from pci_ids.h everywhere. Constify various structs.
Also, fix some random cosmetic issues in the code.
All of this is relatively trivial and tested by manually building
all boards which currently use the i82801xx code.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2951 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
ARRAY_SIZE() can be used on ROMCC-dependent systems. Also adds stdlib.h
to vt8237r_early_smbus.c, so it'll build on those systems.
Signed-off-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2949 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
(ICH/ICH0 up to the ICH9 family) in preparation for further
code improvements for the i82801xx southbridge code.
Small fixes in the 6300ESB PCI IDs.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2947 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
* Remove dead code
* Remove unused variables
* Fix bug where array was one element too small
* Fix error value truncation, the old code never entered the error path
* Remove warnings
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2945 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
ICH5/ICH5R (more to follow) in preparation of further 82801xx improvements.
Use human-readable names for the PCI ID #defines.
Rename *_ISA to *_LPC as per datasheet.
The 82801DBM only has 3 (not 4) USB devices, looks like a copy-paste error.
The fixes in southbridge code are only to keep the build working for now,
any real improvements will only go into the 82801xx code in future.
This is abuild-tested so it shouldn't break anything.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2938 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
the Jetway J7F2 patch that should be coming soon, and also moves most
defines into vt8237r.h. I've changed some of the values from u32 to u8,
because that's all they should ever need to be. Also includes
doxygenized comments!
Signed-off-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2937 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
No functional code changes.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2932 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2. Rename sisnb.c to sis761.c
3. Delete many mis-definition for sis device in
src/include/device/pci_ids.h
4. Trim trailing spaces for all files
Signed-off-by: Morgan Tsai <my_tsai@sis.com>
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2931 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Joseph Smith <joe@smittys.pointclark.net>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2912 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: <corey.osgood@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2907 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
code. This is trivial, I did it for the other components before.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2905 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
southbridge now:
From: Morgan Tsai <my_tsai@sis.com>
It supports SiS761GX / SiS966 chipset, only for AMD K8 platform so far.
Due to integrated VGA sharing system memory, some code in southbridge
folder have to init northbridge.
Copyright (C) 2007 Morgan Tsai <my_tsai@sis.com>
Copyright (C) 2007 Silicon Integrated Systems Corp. (SiS)
Change Log:
Newly support GIGABYTE GA-2761GXDK
CPU type: AMD AM2 socket
Northbridge: SiS 761GX
Southbridge: SiS 966
SuperIO: ITE8716F
Signed-off-by: Morgan Tsai <my_tsai@sis.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2902 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
rodata.pci_driver" warnings are coming from? We were packing those
structures into a read-only segment, but forgot to mark them const.
Despite its size, this is a fairly trivial patch created by a simple
search/replace
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2891 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2883 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Painting the splash graphic is now ifdef'ed.
Signed-off-by: Juergen Beisert <juergen127@kreuzholzen.de>
Acked-by: Peter Stuge <peter@stuge.se>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2836 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
to set up one of five screen resolutions (sorry no autodetection at runtime,
resolution is selected at buildtime) and displays a graphic in the right
bottom corner (splash screen).
Signed-off-by: Juergen Beisert <juergen127@kreuzholzen.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2827 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
i82801DB to reset. See this thread for more info:
http://article.gmane.org/gmane.linux.bios/26791
Signed-off-by: Joseph Smith <joe@smittys.pointclark.net>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2816 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
fixes the problems with PCI add-on cards not being detected or
initialized on MCP55-based systems (PCI bridge decoding change).
I have tested this on the MSI MS-7260 (K9N Neo) with a PCI VGA card,
which worked fine in any of the three PCI slots.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2807 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Reported by Robert Millan.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2801 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This is tested with abuild so shouldn't break anything.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2800 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
For example: in C51/MCP55 or C51/MCP51
Will allow
1. C51 at 0x10 to 0x14, and MCP at 0 to 4
2. C51 at 1 to 4, and MCP at 7 to 0x0a
The reason is c51/mcp51/mcp55 reported unitid is 0x0f (far beyond it
needed), and will prevent us from putting them on bus 0.
Typical values for c51/mcp55 or c51/mcp51:
HT_CHAIN_UNITID_BASE = 0x10 # for C51
HT_CHAIN_END_UNITID_BASE = 0 # for mcp
If only have mcp with c51,
HT_CHAIN_UNITID_BASE = 0 # for MCP
#HT_CHAIN_END_UNITID_BASE = 0 # default value 0x20
Signed-off-by: Yinghai Lu <yinghai.lu@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2776 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
mostly undocumented, had a broken coding style, contained lots of dead
code and had several other problems, e.g. it enabled write access to the
ROM (why?), it unconditionally enabled primary/secondary IDE (which should
have a config option) and that even _twice_ (which is um... wrong).
The new code
- has 'ide0_enable' and 'ide1_enable' config options (which actually
work) to enable/disable the primary/secondary IDE interface in
Config.lb.
- Does _not_ enable write access to the ROM (or is there some good
reason to do that? If so, it should at least have a config option).
- Contains a bit more documentation.
- Uses readable (and documented) #defines instead of hardcoded magic values.
- aaand... it actually compiles ;-) Yep, that's right. The previous code
wouldn't even build, as it hadn't been fully ported from v1 (still used
v1 functions which are simply not available in v2).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2775 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2726 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
southbridges, along with the Asus MEW-VM. With this, my machine attempts to
boot linux, but does so very slowly and fails during the boot process, probably
because of the irq tables.
Signed-off-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Joseph Smith <joe@smittys.pointclark.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2719 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
return that skipped the disable code. This patch removes the return and
fixes the UART disable code.
The problem was that the disable code was ORing bits into the Legacy_IO
MSR causing issues with the LPC SIOs init code that would manifest as a
hang because the IO would not be decoded correctly. ANDing to clear the
bits fixes the issue.
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2706 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
In a mainboard's Config.lb file you can configure whether the primary
and/or secondary IDE interfaces shall be enabled.
Also, various fixups in the rest of the southbridge code, most notably
the early SMBus code, plus some documentation improvements.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Corey Osgood <corey_osgood@verizon.net>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2703 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
accessible (but not writable), so that reading/loading a payload
from that area can work (for instance).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2700 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
the new src/southbridge/amd/cs5536 code completely replaces it.
The Artecgroup dbe61 board currently uses it, but that is broken anyway
at the moment. A fix to use the new CS5536 code for it is being worked on.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2697 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Marc Jones <marc.jones@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2687 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
setup as the host on USB port4. In client mode the headers remain
available. Also fixes an outb to 0x80 to use the post_code() function.
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2660 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2658 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2656 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
-This line, and those below, will be ignored--
M cs5536.c
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2637 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
broke and stopped FILO
from being able to boot.
The fix is a simple one line change plus a comment to
src/mainboard/via/epia/auto.c to write to the IDE
configuration register 0x42 . This has always been done here, however
at some point
something broke it.
The same register was also being set correctly in ide_init(), however
for some reason
this does not work. Possibly the register needs to be set before the IDE
peripheral is enabled
or maybe it is a timing issue.
The section of code in ide_init() (
src/southbridge/via/vt8231/vt8231_ide.c ) that does
write to register 0x42 has been commented out as it is superfluous
and I have added a comment to indicate the reason, should someone at a
future date wonder
why.
I have also changed the default COM speed from 19200 to 115200 in
src/mainboard/via/epia/Options.lb
There has been mention before about the EPIA board not being able to use
115200 but I have seen
no such problems with my board.
Signed-off-by: Ben Hewson <ben@hewson-venieri.com>
This patch worked for me and allowed me to boot Debian kernel
2.5.16-4-486 on an epia 800 mhz system. It is able to consistently get
through the initialization and start init now.
However, after that it crashes at various points in the boot process.
Acked-by: Alex Mauer <hawke@hawkesnest.net>
Note from comitter: I am commiting this, although:
1. it's not the exact right way to fix it up, the chip.h for the sb
should change
2. Alex reports problems, which are almost certainly memory issues.
But it is as close as we've gotten. I can't test it.
Ron Minnich
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2633 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
AMD GX and LX processors. This aguments the previous code, which was
very specific to the OLPC platform with general purpose support and
better integration with the VSA and CPUs.
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2631 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
as that is not RAM but used for other stuff.
First try at PCI init added to src/mainboard/tyan/s1846/Config.lb.
Use a real payload (FILO) per default now.
Note: this cannot boot a payload, yet, but it gets a lot further now.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2623 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2557 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
that's the same as broadcom/bcm5785.
Signed-off-by: bxshi <bingxunshi@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2548 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
2200 (too many names, sounds like a criminal).
1) Linuxbios loads kernel A; kernel A loads kernel B. Everything works
fine.
2) Then I push the reset button.
3) Linuxbios loads kernel A; kernel A loads kernel B. Kernel B complains
about wrong checksum of the mptable and crushes later.
An investigation showed that in 3), short after kernel A (v2.6.19.2)
sets
the Bus Master Enable bit of the nVidia's USB1 controller
(pci_set_master()),
the mptable gets two bytes at physical address 0x80 damaged.
Nothing is plugged to the USB ports. Other two Sun workstations had the
same
behavior. This does not make sense to me unless the controller has a HW
bug.
I believe, this should better be fixed in the kernel USB driver.
For now this patch offers a possibility for linuxbios to reset the USB
controller by setting HostControllerReset bit in HcCommandStatus
Register.
It is enablead by using 'register "usb1_hc_reset"="1"' in 'chip
southbridge/nvidia/ck804' section of the mainboard's Config.lb.
Signed-off-by: Roman Kononov <kononov195-lbl@yahoo.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2546 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
won't compile), and breaks an unnecessary dependency on the usbdebug
code.
Signed-off-by: Ed Swierk <eswierk@arastra.com>
Acked-by: Peter Stuge <peter@stuge.se>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2543 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Yinghai Lu <yinghai.lu@amd.com>
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Yinghai Lu <yinghai.lu@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2540 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
heavily on the code for i82801dbm and i82801er
Signed-off-by: Jon Dufresne <jon.dufresne@gmail.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2534 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
southbridge_intel_i82801dbm_control should be named
southbridge_intel_i82801dbm_ops. Otherwise a compile error occurs if this
device is included in Config.lb of the mainboard.
Closes#62
Signed-off-by: Jon Dufresne <jon.dufresne@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2526 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
space offset 0x1000, and later is the acpi registers also mapped at 0x1000.
This patch fixes this behavior. Closes#44
Signed-off-by: <chn@virtutech.se>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2523 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
same format for all CHIP_NAME() entries in LinuxBIOS (Closes#20).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@linuxbios.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2490 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
long time and I could not get into the tracker.
These are patches to enable ms9185 support. Abuild passes.
Signed-off-by: bxshi <bxshi@msik.com.cn>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2486 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
cs5536, but I don't want to mess up the OLPC, and we really need the lx
support NOW.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2421 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
signed-off-by: Jordan Crouse
Signed-off-by: Ronald G. Minnich
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2410 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This one actualy works. You cannot just go mucking about with stuff that the VSA
has under its thumb. Bad Things happen. This does it the VSA way.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2392 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
USB P4 is disabled by default and we need to setup the mux bits proper
to make it work. This is the frame work for that. All thats needed
is the right address values
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2387 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
here's a patch which replaces all DOS newlines with Unix newlines, and
removes some useless $Rev$, $Id$, and $Header$ tags.
(part 1)
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2385 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
read code. SBbus reads to RAM now work. Yah!
- Rename the register constants to something I can look at
more easily.
- Make the logic flow match the flow from V1 assembly
- #if 0 out other SMbus functions that are still broken.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2353 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
UART. If the upper banks are enabled, then the Linux 8250 driver knows
how to set baud speeds greater then 115200. This was prompted by David
Woodhouse.
Jordan"
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2348 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
add support for NSC pc87351 SuperIO
add Bitworks/IMS manboard config
This is a very basic framework for the i440bx chipset and the
Bitworks IMS board that uses it. Most things are
structure only.
Known issues:
- SMbus reads to the RAM SPD come back
all zero.
- dump_spd_registers() is commented out since it breaks with
the default setting of generic_dump_spd.c where it wants
2 memory controllers.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2347 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
disabled.
cs5536: add new entires for SB control etc.
cs5536.c: chip_enabled function moved to chip_init, so it only gets run
once.
IRQ setup improved
gx2def.h: new defines added
vr.h: new file, with new def's for virtual register control.
mainboard config.lb: new entries added for nb and sb control.
chipsetinit.c: new controls added -- I forget all the details :-)
grphinit.c: new function added
northbridge.c: new IRQ control added. FlashChipSetup added, controlled
by chip info setupflash struct member. Currently, if enabled, this hangs
OLPC in linux PCI scan.
chip.h: new struct members added for unwanted device enable, flash setup
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2345 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
manage them. Make pci_level_irq global. Add value settings for OLPC
rev_a board. Comment out no-longer-needed code in olpc mainboard.c
-- it is replaced by the settings in Config.lb, and the support
in cs5536.c
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2328 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
the result should be ok though..
the purpose is dropping the old i82801er southbridge code
and using the ich5r code instead because its the same chip
but the code looks more solid and is used by many more systems.
Some of the old i82801er features have been ported (like hpet enable)
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2241 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
other fixes for gx2 ram init.
support for sharplfg00l04 -- not working yet.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2197 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This is just a skeleton, basically, and will most likely not even
compile yet.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2164 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
disable agp slot in config.lb
fix error in setting up com1 == should be TTYS0_BAUD
note that the uart8250 struct is a bad design, but so is the
uart8250 code.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2161 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
to fail later than before.
dos2unix'ed the xe7501devkit files, that might have caused some problems
before.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2127 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Special version for HDAMA rev G with 33Mhz test and reboot out.
- Support for CPU rev E, dual core, memory hoisting,
- corrected an SST flashing problem. Kernel bug work around (NUMA)
- added a Kernel bug work around for assigning CPU's to memory.
r2@gog: svnadmin | 2005-08-03 08:47:54 -0600
Create local LNXI branch
r1110@gog: jschildt | 2005-08-09 10:35:51 -0600
- Merge from Tom Zimmerman's additions to the hdama code for dual core
and 33Mhz fix.
r1111@gog: jschildt | 2005-08-09 11:07:11 -0600
Stable Release tag for HDAMA-1.1.8.10 and HDAMA-1.1.8.10LANL
r1112@gog: jschildt | 2005-08-09 15:09:32 -0600
- temporarily removing hdama tag to update to public repository. Will
reset tag after update.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2004 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
1. x86_setup_mtrr take address bit.
2. generic ht, pcix, pcie beidge...
3. scan bus and reset_bus
4. ht read ctrl to decide if the ht chain
is ready
5. Intel e7520 and e7525 support
6. new ich5r support
7. intel sb 6300 support.
yhlu patch
1. split x86_setup_mtrrs to fixed and var
2. if (resource->flags & IORESOURCE_FIXED ) return; in device.c pick_largest_resource
3. in_conherent.c K8_SCAN_PCI_BUS
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1982 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Creator: Li-Ta Lo <ollie@lanl.gov>
More Via EPIA
more via epia stuff, including the trival but fatal bug in auto.c
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1978 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Creator: Yinghai Lu <yhlu@tyan.com>
cache_as_ram for AMD and some intel
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1967 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Creator: Li-Ta Lo <ollie@lanl.gov>
emulator update
x96emu update from Paulo
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1954 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Creator: Li-Ta Lo <ollie@lanl.gov>
TLA is really diffcult to use. How am I going to
roll back my last commit ?
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1953 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Creator: Li-Ta Lo <ollie@lanl.gov>
emulator update
Correction to the reduce emulator from Paulo
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1952 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Creator: Yinghai Lu <yhlu@tyan.com>
set CK804 nic mac addr in MMIO instead of pci config
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1948 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Creator: Yinghai Lu <yhlu@tyan.com>
nvidia onboard lan support
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1947 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
smbus_read_byte routine updated as per suggestion by rgm
addition reset & wait_until_ready to allow correct reading of first
byte on epia systems.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1807 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Set adl855pc ROM_SIZE to 1M
Other minor debug prints until we get this fixed.
We're almost as far along as we were before the Change :-)
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1780 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
crt0.S.lb: Modified so that it is safe to include console.inc
console.c: Added print_debug_ and frieds which are non inline variants of the normal console functions
div64.h: Only include limits.h if ULONG_MAX is not defined and define ULONG_MAX on ppc
socket_754/Config.lb Conditionally set config chip.h
socket_940.c We don't need and #if CONFIG_CHIP_NAME we won't be linked in if there are no references.
slot_2/chip.h: The operations struct need to be spelled cpu_intelt_slot_2_ops
slot_2/slot2.c: The same spelling fix
socket_mPGA603/chip.h: again
socket_mPGA603/socket_mPGA603_400Mhz.c: and again
socket_mPGA604_533Mhz/Config.lb: Conditionally defing CONFIG_CHIP_NAME
socket_mPGA604_800Mhz/chip.h: Another spelling fix
socket_mPGA604_800Mhz.c and again
via/model_centaur/model_centaur_init.c: It's not an intel CPU so don't worry about Intel microcode uptdates
earlymtrr.c: Remove work around for older versions of romcc
pci_ids.h: More ids.
malloc.c: We don't need string.h any longer
uart8250.c: Be consistent when delcaring functions static inline
arima/hdama/mptable.c: Cleanup to be a little more consistent
amdk8/coherent_ht.c:
- Talk about nodes not cpus (In preparation for dual cores)
- Remove clear_temp_row (as it is no longer needed)
- Demoted the failure messages to spew.
- Modified to gracefully handle failure (It should work now if cpus are removed)
- Handle the non-SMP case in verify_mp_capabilities
- Add clear_dead_routes which replaces clear_temp_row and does more
- Reorganize setup_coherent_ht_domain to cleanly handle failure.
- incoherent_ht.c: Clean up the indenation a little.
i8259.c: remove blank lines at the start of the file.
keyboard.c: Make pc_keyboard_init static
ramtest.c: Add a print out limiter, and cleanup the printout a little.
amd8111/Config.lb: Mention amd8111_smbus.c
amd8111_usb.c: Call the structure usb_ops not smbus_ops.
NSC/pc97307/chip.h: Fix spelling issue
pc97307/superio.c: Use &ops no &pnp_ops.
w83627hf/suerio.c: ditto
w83627thf/suerio.c: ditto
buildrom.c: Use braces around the body of a for loop. It's more maintainable.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1778 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Move pci_set_method out of hardwaremain.c
- Re-add debugging name field but only include the CONFIG_CHIP_NAME is
enabled. All instances are now wrapped in CHIP_NAME
- Many minor cleanups so most ports build.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1737 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
ram linuxbios_ram instead of linuxbios_c and linuxbios_payload...
- Reordered the linker sections so the LinuxBIOS fallback image can take more the 64KiB on x86
- ROM_IMAGE_SIZE now will work when it is specified as larger than 64KiB.
- Tweaked the reset16.inc and reset16.lds to move the sanity check to see if everything will work.
- Start using romcc's built in preprocessor (This will simplify header compiler checks)
- Add helper functions for examining all of the resources
- Remove debug strings from chip.h
- Add llshell to src/arch/i386/llshell (Sometime later I can try it...)
- Add the ability to catch exceptions on x86
- Add gdb_stub support to x86
- Removed old cpu options
- Added an option so we can detect movnti support
- Remove some duplicate definitions from pci_ids.h
- Remove the 64bit resource code in amdk8/northbridge.c in preparation for making it generic
- Minor romcc bug fixes
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1727 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- mem.h and sizeram.h and all includes killed because the are no longer needed.
- linuxbios_table.c updated to directly look at the device tree for occupied memory areas.
- first very incomplete stab a converting the ppc code to work with the dynamic device tree
- Ignore resources before we have read them from devices, (if the device is disabled ignore it's resources).
- First stab at Pentium-M support
- add part/init_timer.h making init_timer conditional until there is a better way of handling it.
- Converted all of the x86 sizeram to northbridge set_resources functions.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1722 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This is way to much code duplication but for now things work.
- Fix the typo in amd8111_lpc.c
- Remove an unused macro, use continue instead of break in mtrr.c
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1704 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Enable resources on the lpc bus. PCI now longer do this by
default for their children unless they are bridges.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1703 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Rename chip_config chip_operations throughout the tree
- Fix Config.lb on most of the Opteron Ports
- Fix the amd 8000 chipset support for setting the subsystem vendor and device ids
- Add detection of devices that are on the motherboard (i.e. In Config.lb)
- Baby step in getting the resource limit handling correct, Ignore fixed resources
- Only call enable_childrens_resources on devices we know will have children
For some busses like i2c it is non-sense and we don't want it.
- Set the resource limits for pnp devices resources.
- Improve the resource size detection for pnp devices.
- Added a configuration register to amd8111_ide.c so we can enable/disable individual ide channels
- Added a header file to hold the prototype of isa_dma_init
- Fixed most of the superio chips so the should work now, the via superio pci device is the exception.
- The code compiles and runs so it is time for me to go to bed.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1698 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Unified AMD K8 reset function that can be customized via mainboard Config.lb
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1471 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Reworked pnp superio device support. Now complete superio support is less than 100 lines.
- Added support for hard coding resource assignments in Config.lb
- Minor bug fixes to romcc
- Initial support for catching the x86 processor BIST error codes. I've only seen
this trigger once in production during a very suspcious reset but...
- added raminit_test to test the code paths in raminit.c for the Opteron
- Removed the IORESOURCE_SET bit and added IORESOURCE_ASSIGNED and IORESOURCE_STORED
so we can tell what we have really done.
- Added generic AGP/IOMMU setting code to x86
- Added an implementation of memmove and removed reserved identifiers from memcpy
- Added minimal support for booting on pre b3 stepping K8 cores
- Moved the checksum on amd8111 boards because our default location was on top of
extended RTC registers
- On the Hdama added support for enabling i2c hub so we can get at the temperature
sensors. Not that i2c bus was implemented well enough to make that useful.
- Redid the Opteron port so we should only need one reset and most of memory initialization
is done in cpu_fixup. This is much, much faster.
- Attempted to make the VGA IO region assigment work. The code seems to work now...
- Redid the error handling in amdk8/raminit.c to distinguish between a bad value
and a smbus error, and moved memory clearing out to cpufixup.
- Removed CONFIG_KEYBOARD as it was useless. See pc87360/superio.c for how to
setup a legacy keyboard properly.
- Reworked the register values for standard hardware, moving the defintions from
chip.h into the headers of the initialization routines. This is much saner
and is actually implemented.
- Made the hdama port an under clockers BIOS. I debuged so many interesting problems.
- On amd8111_lpc added setup of architectural/legacy hardware
- Enabled PCI error reporting as much as possible.
- Enhanded build_opt_tbl to generate a header of the cmos option locations so
that romcc compiled code can query the cmos options.
- In romcc gracefully handle function names that degenerate into function pointers
- Bumped the version to 1.1.6 as we are getting closer to 2.0
TODO finish optimizing the HT links of non dual boards
TODO make all Opteron board work again
TODO convert all superio devices to use the new helpers
TODO convert the via/epia to freebios2 conventions
TODO cpu fixup/setup by cpu type
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1390 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Support for compiling romcc on non x86 platforms
- new romc options -msse and -mmmx for specifying extra registers to use
- Bug fixes to device the device disable/enable framework and an amd8111 implementation
- Move the link specification to the chip specification instead of the path
- Allow specifying devices with internal bridges.
- Initial via epia support
- Opteron errata fixes
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1200 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
* subtractive resources
* merging with the static device tree
* more device types than just pci
- The piece to watch out for is the new enable_resources method that was needed in all of the drivers
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1096 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- SMP cleanups (remove SMP only use CONFIG_SMP)
- Minor tweaks to romcc to keep it from taking forever compiling
- failover fixes
- Get a good implementation of k8_cpufixup and sizeram for the opteron
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@998 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Add initial support for the amd8131
- Update the mptable to something possible
- hdama/Config add the amd8131 southbridge
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@968 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Minor romcc fixes
- In smbus_wail_until_done a romcc glitch with || in romcc where it likes
to run out of registers. Use | to be explicit that I don't need the short
circuiting behavior.
- Remove unused #defines from coherent_ht.c
- Update the test in auto.c to 512M
- Add definition of log2 to romcc_io.h
- Implement SPD memory sizing in raminit.c
- Reduce the number of memory devices back 2 to for the SOLO board.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@883 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Update apic.h to include the APIC_TASK_PRI register definition
- Update mptable.c to have a reasonable board OEM and productid
- Additional testfiles for romcc.
- Split out auto.c and early failover.c moving their generic bits elsewere
- Enable cache of the rom
- Fixes to amd8111_lpc.c so that we successfully setup virtual wire mode on the ioapic
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@880 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The goal is to have the same interface with or without romcc.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@868 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Implementation of fallback/normal support for the amd solo board
- Minor bugfix in romcc
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@867 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Stefan Reinauer