Explicitly configure the minimum assertion width values to ensure
that they are set as expected and are not using unknown defaults.
Change-Id: I9a88e5b6002137df6e572b84d0de8a69522938f9
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30722
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Enable the active-low recovery mode GPIO now that new boards are
available which have an external pull-up instead of a pull-down so
it can be asserted properly by servo.
This was tested on a Sarien system by holding the recovery button
on the servo board and tapping the cold reset button and ensuring
that it enters recovery mode.
Change-Id: I3216580bc94de71b05bf9382f15d0c4d428cb9fa
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30721
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
These platforms use the standard fixed function power button
and do not need a second power button device declared or the
kernel will end up with two devices reporting the same event.
Change-Id: I6fe2b201a6a6f6307a0c4bd6a61f56cfcdd88bf4
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30720
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Expose the FSP tunables for the chipset minimum assertion width
settings which can be configured per-board.
The defaults appear to be different from what is listed in the FSP
header documentation so I tried to list what the actual default is
based on the source rather than what is stated the header comments.
Change-Id: Ie0606c2984727adf13c9fb8395586287162e49ca
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30719
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Add logging of chipset events on boot into the flash event log.
This was tested on a google/sarien board to ensure that events
like "System Reset" are added to the log as expected.
Change-Id: I38498cef36d8cc9c8a1f63d12618ea768b65254c
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30718
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
This structure is declared as a static CAR_GLOBAL in the common
PMC library code and in the SOC specific code. Remove the SOC
specific version and instead get the chipset_power_state pointer
from the PMC library.
This fixes events that were recorded in chipset_power_state at
boot but were reading as all zero when it was time to parse the
structure when logging events to flash.
Change-Id: I67a4f724c0707d98766ad28abd8d0b66a5615745
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30717
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Link walkfcbfs.S in the C_ENVIRONMENT_BOOTBLOCK case and also in the
romstage.
This is useful for cbfs access in pre-CAR environments.
Change-Id: I9a17cdf01c7cbc3c9ac45ed1f075731f3e32f64b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30681
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
The result is saved in a static variable and is reported when the
console is initialised.
Change-Id: I5f0f9edce68634adfe4a77a0d2c0bf3d7cd4e78e
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30671
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Pass timestamps and BIST to romstage using the same signature
as C_ENVIRONMENT_BOOTBLOCK will.
Change-Id: Ic90da6b1b5ac3b56c69b593ba447ed8e05c8a4e2
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30492
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Have same usage of registers with romcc bootblock
and C_ENVIRONMENT_BOOTBLOCK.
Change-Id: Ibfa80e40f0b736a904abf4245fc23efc0cdc458d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30490
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This removes the need to synchronize the devicetree and the romstage
writing to FD.
Change-Id: I83576599538a02d295fe00b35826f98d8c97d1cf
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30244
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The southbridge has the function disable bits for port 5 and 6
strapped RO to 1 (disable).
Change-Id: I2948935d42b9031d61f9e5b3f06b769e68f5a042
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30712
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
The devicetree was synced incorrectly with respect to the function
disable register set in romstage.
Change-Id: I189c5fdc433b5577ae008abf42878cdc6e3f2d52
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30711
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch fixes icelake build brokenness due to bootblock size
issue.
Increase the bootblock size to 48K to match skylake. With UART
enabled we are very near the 32K limit, and with upcoming changes
to add USB devices in devicetree for a icelake board it is over
the current 32K limit.
BUG=b:122485106
TEST=Able to build dragonegg
Change-Id: I66706e66ac1bce677fe11022d0eef44b9efc2e76
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/30702
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
For these platforms, the first PCI node on devicetree
is not the root of PCI bus hierarchy, and the topology
(bus->children and dev->sibling links) are getting
manipulated during HyperTransport enumeration.
This workaround reverts back to old dev_find_slot() with
its bad semantics.
Change-Id: I19745c3070c12e562ffab2f0243c9d91dd051c72
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30695
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Libgfxinit provides a better alternative to the native C init. While
libgfxinit mandates an ada compiler, we want to encourage use of it
since it is in much better shape and is actually maintained.
This way libgfxinit also gets build-tested by Jenkins.
Change-Id: I540cf08cef6ff7825694ebfa36e2e6437916e657
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/27016
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Following changes are done to enable touch screen support on hatch
1. Enable I2C1 device at 400Khz at 3.3V
2. Configure GPIO for touch screen
3. Add ACPI entry for ELAN touch panel
4. update GPIO table with not connected GPIO pins for panel
BUG=b:120914069
BRANCH=none
TEST=check if code compiles with changes.
Change-Id: I8dab07dad4cb197865bb9cf0e8da240810fcfabe
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/30425
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
If requested EHCI function is not on bus 0, we would
need to open MMIO windows and configuration register
space for the connected upstream PCI bridge for it
to work. We don't plan to do so.
Change-Id: I7c1c60f9d9890dedfedc9d977faf5152ba362692
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30692
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
The first stage attempting to initialise usbdebug
gadget will leave it marked as non-present if none
is detected. This allows further stages to bypass
usbdebug init sequence.
Change-Id: I1491d7fab3c89f210fb03b32481f697bc7a1d1e6
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30622
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
The EHCI hardware needs to be initialized only once during CAR stages.
Some exception need to be made when a blob messes with the EHCI
hardware. To achieve this add a fixed location in the car.ld linker
script such that the ehci debug information can be shared across CAR
stages.
Currently this means only romstage and bootblock, but verstage can
also be hooked up later on.
Tested on google/peppy: Both the bootblock and the romstage properly
output console.
Change-Id: I78e20a172fd5cc81f366d580f3cce57b9545d7a2
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30481
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Main objective for this change is to export the bluetooth reset
gpio to the kernel for use in an rf-kill operation.
To do so, we enable USB acpi and define all of the USB2 devices,
which includes bluetooth's reset gpio information.
BUG=b:119899987
TEST=build and flash to rammus, log into rammus and
'cat /sys/firmware/acpi/tables/SSDT > /tmp/ssdt.dml', copy
that ssdt.dsml to /tmp/ssdt.dml on host machine,
'iasl -d /tmp/ssdt.dml', then verify that "reset gpio"
shows up in the HS03 node's _DSD package in the table.
Signed-off-by: marxwang <marx.wang@intel.com>
Change-Id: Ieadb3609c7634a20e96c7c4dfb96f5e3f23e468b
Reviewed-on: https://review.coreboot.org/c/30607
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Zhuohao Lee <zhuohao@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Elan touchpad require connected i2c clock to be running at 400Khz, with
the modification can get 404Khz speed from Arcada EVT platform.
BUG=b:119628524
TEST=Build and boot up on Arcada platform, measure the i2c clock is
around 400Khz.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: If717cdd6b73394125df54d90f729ffb4ef37b087
Reviewed-on: https://review.coreboot.org/c/30653
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
The newest and most useful incarnation was hiding in soc/intel/common/.
We move it into the Mainboard menu and extend it with various flags to
be selected to control the default and which options are visible. Also
add a new `int` config MAINBOARD_POWER_FAILURE_STATE that moves the
boolean to int conversion into Kconfig:
0 - S5
1 - S0
2 - previous state
This patch focuses on the Kconfig code. The C code could be unified as
well, e.g. starting with a common enum and safe wrapper around the
get_option() call.
TEST=Did what-jenkins-does with and without this commit and compared
binaries. Nothing changed for the default configurations.
Change-Id: I61259f864c8a8cfc7099cc2699059f972fa056c0
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/29680
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
The vbt was extracted from the option rom found on stock images.
The vbt.bin is the same across all variants.
The VBT has a modified BDB block 43, the 'Backlight info block' such
that the inverter type for the panel in use is set to
2 (BDB_BACKLIGHT_TYPE_PWM) instead of 0 (BDB_BACKLIGHT_TYPE_NONE).
This only seems to matter on Windows, as without it changing the
backlight duty cycle does not work.
Change-Id: I82c72c561e1058e0b77d80baf330b64f7c6b08e3
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30487
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently this needlessly initializes the hardware in the both the
romstage and the bootblock, but it works.
Build option is renamed to USBDEBUG_IN_PRE_RAM to reflect the
use better, related support files can be built to pre-ram stages
regardless of usbdebug being enabled or not.
Tested on Google/peppy (adapted to C_ENVIRONMENT_BOOTBLOCK).
Change-Id: Ib77f2fc7f3d8fa524405601bae15cce9f76ffc6f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30480
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This allows to set up the SuperIO in the C_ENVIRONMENT_BOOTBLOCK
bootblocks. It is likely unnecessary to do this in verstage.
This also renames COMMON_ROMSTAGE to COMMON_PRE_RAM.
Change-Id: I3d999611baa1e79c79fe6b1f01822ebaa5f85daf
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30672
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Without eist enabled, fizz's CPU clocks are locked at the
base frequency, and don't scale up or down. This prevents
fizz from idling properly and turbo boost from functioning,
so enable it (as is done for all other KBL boards)
Test: build/boot google/fizz, ensure CPU clocks scale as expected
Change-Id: I77dd0e1df1bf88f5bae18e9f832ca8d60fb777b4
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30674
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This is done for consistency purposes. Also fix a small formatting issue
in a function.
Change-Id: I5dc170dbca59b7abbc912f9a26f76886b25ad82f
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30654
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Expose the function that can unconditionally re-initialise
EHCI debug host and gadget.
Given the missing header in soc/intel files that prevented
building with USBDEBUG_IN_ROMSTAGE=y, it is not actually
known if those SOCs work at all for usbdebug.
Change-Id: I8ae7e144a89a8f7e5f9d307ba4e73d4f96401a79
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30557
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
currently, if the IA32_FEATURE_CONTROL lock bit is already
set, VMX status isn't reported. Adjust debug output to
provide more useful infomation on both VMX and lock bit statuses.
Test: build/boot google/chell, observe useful output in cbmem log
regardless of lock bit status.
Change-Id: Ie50f214f7e3fcfd6c3d0d2de034a93518c0a6b46
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30524
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
We have init_bootmode_straps() defined for the same purpose.
Change-Id: Ia2692d8f8986247ea4ce889d6252d3c4c8b27bc4
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30398
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add possibility to update microcode from BLOBs repo.
No need to copy headers around which have an unclear license.
Tested on wedge100s:
* Microcodes are included into FIT.
* Still boots to Linux.
* 3rdparty/blobs at dd00ad1260ef1dc0ba8c55c06ab10c7639dc3eb1
Change-Id: I8ecfb7302a7fc847a51934942f6d323a4f96abba
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/30324
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Note that while these boards had entry 0x0ff0 in comparison
to 0x0ffc of the get_default_pci1234() initialisation, the
implementation of get_pci1234() unconditionally overrides
the first entry.
Change-Id: I8bec612f84fe3c3a0c21fc1e10629368857e9c5e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30649
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
All these boards use the same default initialiser.
As this is initialized late after device enumeration,
it can't really be used to alter platform configuration.
Change-Id: I30fc0298081df0442ec4e9a527340b93a3cd6106
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30648
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Values in the array are not used anywhere.
Change-Id: Iee92f903db97533709d54d1f214f2f23a1fab06b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30638
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Values in the array are not used anywhere.
Change-Id: I608b8c2e21bc515c56a27982815c1da43f3bb976
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30637
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
It has to be called once before PIRQ and MP table generation.
Change-Id: I238c6b4810404d320b36d4f6b4a161c1ff11c8d3
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30630
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Also remove global ramstage-y += get_bus_conf.c, this is
specific to amdfam10.
Change-Id: I49b604ebff6bcfe85518b2c3896ab798c3c7878d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30629
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Value of the global is never evaluated.
Change-Id: I74106b0f5f033053288882a5bcd3c1dba3235ac0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30628
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
These few cases lacked a proper devfn parameter in the
form of PCI_DEVFN(dev, fn).
Change-Id: Iad0b214df12dee65360d07e887a960b0c73a3e4f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/26481
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Semantics of dev_find_slot() are ill in the sense that
it only works after device enumeration has completed in
ramstage. Plan is to declare it as deprecated.
Introduce pcidev_on_root() and pcidev_path_on_root()
functions to replace cases where this was called with
static argument bus == 0. New implementation only walks
the root bus of the PCI tree, while old one walked
the entire linked list of devices.
Introduce pcidev_path_behind() to replace cases where
argument bus != 0. The required parent node is typically
one of the PCIe root functions that you locate using
pcidev_on_root() above.
New forms are safe to use with early devicetree and
before PCI bus numbers have been assigned.
Change-Id: Ie20598d48b4cf6e35e45fc90804bad4728437fc6
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/26447
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Definitions of these types are arch-agnostic. Shared device
subsystem files cannot include arch/pci_ops.h for ARM
and arch/io.h for x86.
Change-Id: I6a3deea676308e2dc703b5e06558b05235191044
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/29947
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Use of device_t is deprecated.
Change-Id: Ie05869901ac33d7089e21110f46c1241f7ee731f
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/30047
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This was already disabled and mostly incompatible
with romstage having stack in CAR.
Change-Id: I1fe02bef668a5bc8ce3d5a1d8090670752b10c3e
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30621
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
The result is that i82801{g,i,j}x now use the correct _PRT table for
their root port number.
Change-Id: I92bba3c669f3e6a44a42e19a88a33dfcfc2b9b42
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30528
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Add DRAM support for google kukui.
BUG=b:80501386
BRANCH=none
TEST=Boots correctly on Kukui
Change-Id: I1ed01404343745c883b22a648966327bdcabc5c2
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/28438
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Write a range of memory with special pattern, and read it back to check
whether the read value same as write.
The test pattern include 8bit offset read write, 16 bit offset read
write, 32bit offset read write, and cross testing.
BUG=b:80501386
BRANCH=none
TEST=Boots correctly on Kukui, and inits DRAM successfully with related
patches.
Change-Id: I30d5fbd3db2acf36e3058ba4f34558b981fba78c
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/28845
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: You-Cheng Syu <youcheng@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
BUG=b:80501386
BRANCH=none
TEST=Boots correctly on Kukui, and inits DRAM successfully with related
patches.
Change-Id: Id1e8862ff6feb9628d37fe5300780ff56865a563
Signed-off-by: Huayang Duan <huayang.duan@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/28844
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
This patch is from Linux, commit 3856081eede2. The commit message there
is:
> commit 3856081eede297b617560b85e948cfb00bb395ec
> Author: Y.C. Chen <yc_chen@aspeedtech.com>
> Date: Thu Feb 23 15:52:33 2017 +0800
>
> drm/ast: Fix AST2400 POST failure without BMC FW or VBIOS
>
> The current POST code for the AST2300/2400 family doesn't work properly
> if the chip hasn't been initialized previously by either the BMC own FW
> or the VBIOS. This fixes it.
>
> Signed-off-by: Y.C. Chen <yc_chen@aspeedtech.com>
> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
> Tested-by: Y.C. Chen <yc_chen@aspeedtech.com>
> Acked-by: Joel Stanley <joel@jms.id.au>
> Cc: <stable@vger.kernel.org>
> Signed-off-by: Dave Airlie <airlied@redhat.com>
Tested on a Supermicro X10SLM+-F with an AST 2400 where the BMC flash
chip has been completely erased. Before the patch, the display resembled
a rainbow. After the patch, the display works well.
Original-Signed-off-by: Y.C. Chen <yc_chen@aspeedtech.com>
Original-Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Original-Tested-by: Y.C. Chen <yc_chen@aspeedtech.com>
Original-Signed-off-by: Dave Airlie <airlied@redhat.com>
Change-Id: I72efcf907fbd1263fe21d4f36fe900b305419c44
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/c/30507
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Follow instrcution from https://doc.coreboot.org/acpi/gpio.html to
implement GPIO toggling method, covered for both CNP_LP and CNP_H pch.
BUG=N/A
TEST=Build and boot up fine on sarien platform, add an dummy STSX in
DSDT table, read back from iotools to confirm the GPIO tx state get
updated.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I006a6a8fc580c73ac0938968397a628a4ffe504f
Reviewed-on: https://review.coreboot.org/c/30461
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This means that any PCIe device placed in a PEG slot should now work.
During S3 resume, link training sometimes does not complete before
device enumeration. However, no tangible issues have been observed.
Fixing it would introduce a rather large delay in S3 resume.
There are a few minor shortcomings:
- Using PEG for display output is not yet supported.
- Only PEG2 is supported. An extra (unknown) training sequence is said to
be needed for PEG3.
- The ACPI _PRT method is not yet generated, so legacy interrupt routing
doesn't work for devices with multiple functions.
Tested on an ASRock H81M-HDS. Using a Radeon HD 6450 graphics card works
under GNU/Linux, with PRIME [1]. An x1 PCIe card was also tested in the
PEG slot, and it appears functional.
[1]: https://wiki.archlinux.org/index.php/PRIME
Change-Id: I786ecb6eccad8de89778af7e736ed664323e220e
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/c/30272
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
If PCIe root port `n` is disabled, then `rpc.ports[n - 1]` remains NULL.
The existing Lynx Point systems probably don't end up dereferencing
NULL pointers this way. However, it might occur on a system using
Flexible I/O to remap PCIe root ports to other functions.
Tested on an ASRock H81M-HDS and an Acer C720 (Google Peppy). No issues
presented themselves.
Change-Id: I2c22fa36217766c2c4d6e8046f99989063066b16
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/c/30079
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Using a linked C file is the standard approach for GPIO settings.
Change-Id: I6a5ca65bc1553bd382589d67379eafd03dc0b0a3
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/c/30503
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
The existing SATA ACPI code for Lynx Point implements some methods and
devices, but not completely. These methods are optional and only used in
IDE mode. The code was likely copied from bd82x6x, where it has since
been removed.
As a result, many remarks produced by iasl about unreferenced objects
are eliminated.
Tested on an ASRock H81M-HDS and an Acer C720. No issues with SATA
were observed.
Change-Id: I808a9dff7b9ba34239ffd95fa4cb9b39b10c4b62
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/c/30149
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This either sets unwanted or unnecessary settings.
Tested. Everything still works fine.
Change-Id: I0f552dea1b37cdc17c9dd26a0294b59063cdc2be
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30402
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
ENABLE_VMX is CPU specific and it is already enabled here:
src/cpu/intel/common/Kconfig
Change-Id: I130738aa3758a9212bab10f90edb7b2ab6830597
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/30605
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Cases of *dev = PCI_DEV(b,d,f) are invalid. Not caught
because files only build with __SIMPLE_DEVICE__ defined.
Remove cases of testing __SIMPLE_DEVICE__ in files that
are not build for ramstage.
Change-Id: If10a0efa187c9b1d9a5577008aa46f050f0aa309
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30497
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Add reset delay in power resource to prevent from failing to bind after
unbinding. And boards including yorp series - bobba / phaser and bip series
- ampton are affected.
BUG=b:121286833
BUG=b:117474421
BUG=b:121019320
BRANCH=None
TEST=emerge-octopus coreboot,
verified that WACOM touchscreen can re-bind successfully.
Change-Id: Icf690fc8e9450d559b642d1c88e29ff5d52c5488
Signed-off-by: Marco Chen <marcochen@chromium.org>
Reviewed-on: https://review.coreboot.org/c/30422
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Set PchCnvimode to Auto if CNVi is enabled in device tree. This will
allow FSP to configure CNVi.
Change-Id: I4f77fe5e9f561d3b498403e42dfc7afdcfaedf6f
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/30516
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Correcting order of display related GPIOs and also adding not connected
pin definitions for display GPIOs
BUG=b:120914069
BRANCH=none
TEST=check if code compiles with changes.
Change-Id: I9498284d263516f65513d6395883b6b09dd70fd5
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/30544
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
This patch enables the SATA for hatch,
* Enable the SATA port 1.
* Configure the GPIO for SATA.
BUG=b:120914069
BRANCH=none
TEST=USE="-intel_mrc -bmpblk" emerge-hatch coreboot.
Change-Id: Iaf800d1531688c3d3b82600038ea1d7160ae4b0b
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/30435
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The feature is used to enable PCI MMIO accesses behind
PCIe links (or bridges) before PCI enumeration has been
completed.
Add the feature for bootblock, verstage and postcar, it
is required with add-on PCIe serial cards for early
console output. It's up to the board specific code to
configure PCIe root port prior to calling console_init()
for this to work.
Remove feature from ramstage, it bypasses any resource
allocations and bus number assignments.
For the moment PCI configuration support before ramstage
is available only on ARCH_X86.
Also switch from device_t to pci_devfn_t.
Change-Id: I08acec68b6f17f4d73d30039cc41274492ea4f45
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30496
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Add symbols for the non C_ENVIRONMENT_BOOTBLOCK builds
and use them for stack guards.
Change-Id: Ib622eacb161d9a110d35a7d6979d1b601503b6f4
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30491
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
The same file was replicated three times for certain
soc/intel bootblocks, yet there are no indications or need to do
chipset-specific initialisation.
There is no harm in storing the TSC values in MMX registers
even when they would not be used.
Change-Id: Iec6fa0889f5887effca1d99ef830d383fb733648
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30393
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Platforms with SSE=y or SSE2=y will invoke romcc with -mcpu=k7.
This implicitly enabled romcc to consume MMX registers, if XMM
set was consumed first.
Explicitly tell romcc not to clobber MMX set.
Change-Id: I37f1d6ea01873036712dfbb32bb1dcd5d769e85d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30392
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This board runs well with coreboot. The documentation part of this
commit lists what works and what doesn't.
Tested with GRUB 2.02 as a payload, loading SeaBIOS 1.12.0 which then
boots FreeBSD 11.2. It has also been tested with GRUB directly booting
Debian GNU/Linux 9.6 (kernel 4.9).
Change-Id: I291573d4651bdffe24eb841033ea6189fcbf8502
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/c/30357
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The function pch_log_state() was overlooked when making the smi
relocation code common.
Change-Id: I878772f1a93105b828e50f37e105d04988ba0bdf
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30426
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Processor graphics is disabled on, for example, the C222 and C224
chipsets.
The change to resource assignment in northbridge.c prevents the following
warning that occurs when the IGD is disabled:
> skipping PCI: 00:00.0@3 fixed resource, size=0!
Tested on a Supermicro X10SLM+-F, which has the IGD disabled by the
chipset. The graphics memory is reclaimed and no issues were observed.
Also tested on an ASRock H81M-HDS. This board has an IGD, but no
regressions were observed.
Change-Id: I86d4aef50b6588f08b86c9758a4b95ccd65e9a96
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/c/30271
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The existing code sets DEVEN with the intention of enabling the IGD and
Mini-HD audio. However, according to the datasheet [1] and some testing
on hardware, the bits in DEVEN are set by default if and only if the
straps/fuses say the device should be enabled. To illustrate this, here
are a few initial values of DEVEN on some Haswell systems:
Supermicro X10SLM+-F: 0x0000002d
ASRock H81M-HDS: 0x00000039
Acer C720: 0x000000b1
On the X10SLM+-F, the IGD is disabled by default, and PEG10 & PEG11
are enabled by default. On the C720, the PEG devices are all disabled
by default, while the IGD and Mini-HD audio are already enabled.
There are two issues that result from the existing behaviour: PEG
devices are unconditionally disabled, and devices are set as enabled
when it's not actually possible to enable them.
So, don't touch the DEVEN register at this stage, as there are no
benefits.
Interestingly, on an Acer C720 (Google Peppy), a PCI device 00:04.0
appears. It is a thermal sensor. `powerstat` was used to measure idle
power usage over 30 minutes under Debian GNU/Linux 9.6. There was no
change in reported power draw.
[1] Desktop 4th Generation Intel® Core TM Processor Family, Desktop
Intel® Pentium® Processor Family, and Desktop Intel® Celeron®
Processor Family Datasheet – Volume 2 of 2.
December 2013, revision 003, document number 328898.
Change-Id: I242f9138472de5a0b26b5852f632b53b2920132d
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/c/30269
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This allows devices to be properly disabled when they are set to `off`
in the devicetree, or when a device has its `enabled` property set to
false.
A message is printed stating that a device is being disabled, even if
it was already disabled via DEVEN. However, it could be useful to have
this information, so such messages are kept.
The device 00:04.0 is a thermal sensor on the Acer C720, but it has not
been named as such in this patch. This is because the public datasheets
never formally acknowledge what the device is, and how it might differ
across platforms.
Tested on a Supermicro X10SLM+-F. The Mini-HD audio is disabled now,
silencing a warning from Linux.
Also tested on an Acer C720 (Google Peppy). Disabling "device 4" from
devicetree.cb works.
Also tested on an ASRock H81M-HDS. For this device, and all other test
devices, there were no regressions observed.
Change-Id: If1504e620967449a09f113a7c771a1ec30380644
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/c/30270
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Internal pull up need to be enabled for GPD3 as power button pin for
PCH according cannonlake pch EDS vol1 table 17-1. Without that pin will
stay floating and hook up XDP can cause system shutdown as power buttone
event will trigger.
BUG=N/A
TEST=Hook up XDP on sarien platform, able to boot up into OS and stay
at power up state.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: Ibe21da5f4a0797a3d62b36899f023908b46c25bf
Reviewed-on: https://review.coreboot.org/c/30374
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
On some platforms SVI command completion is not reported by
voltage regulator. Because of that CPU got stuck in invalid
P-State, which resulted in lower frequency and inability to
reboot platform without performing cold reset.
Change-Id: I260c997f3a0f4547041785a3b9de78e34d22812a
Signed-off-by: Krystian Hebel <krystian.hebel@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/30367
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-by: Piotr Król <piotr.krol@3mdeb.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
CPUID 0xf47 tested on on 945G-M4 board.
Needs more MSR's consistency tests.
To do: test if speedstep.c and speedstep/acpi.c
are ok for model_f4x.
Change-Id: I285ad33804592e3df510d61dd24f14f944e05142
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/17409
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Commit 8cf8aa2 [ec/google/chromeec: Use common MEC interface]
changed the return mechanism for the checksum on reads/writes
for MEC devices, but incorrectly handled the passed-in csum
parameter by not dereferencing. This led to the returned csum
value always being zero, which causes all EC commands with non-
NULL data_in to fail with a checksum error.
Fix this by storing the returned checksum in a temp variable,
and only assigning to csum when the pointer isn't NULL;
Test: build/boot google/chell, verify EC hello command succeeds,
keyboard backlight turned on at boot.
Change-Id: I7122c3fdc5a19f87f12975ee448728cf29948436
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30444
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Modify the vbios's eDP signal setting from level0(0dB)
to level1 (3.5dB) for bard
Add VBT blobs and include it in cbfs
BUG=b:119448457
TEST=Test & measure eDP signal
Change-Id: I0b854a6adad43844282aed61d26e798727b5cb62
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30375
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This adds a convenient helper function to add vbt binaries to cbfs.
Change-Id: I80d9b3421f6e539879ad4802119fe81d7ea1e234
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30430
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The H81 chipset is the only non-LP Lynx Point chipset with 6 PCIe root
ports, all others have 8 [1]. The existing PCIe code assumed that all
non-LP chipsets had 8 root ports, which meant that port 6 would not be
considered the last root port on H81, so `root_port_commit_config()`
would not run. Ultimately, while PCIe still worked on H81, all the root
ports would remain enabled, even if disabled in the devicetree.
Also, remove `PCI_DEVICE_ID_INTEL_LYNXPOINT_MOB_DESK_{MIN,MAX}`, as they
are unused, and the MAX constant is incorrect.
Interestingly, this fixes an issue where GRUB is unable to halt the
system.
Tested on an ASRock H81M-HDS. The root ports disabled in the devicetree
do indeed end up disabled.
[1] Intel® 8 Series/C220 Series Chipset Family Platform Controller Hub
(PCH) Datasheet, revision 003, document number 328904.
Change-Id: If3ce217e8a4f4ea4e111e4525b03dbbfc63f92b0
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/c/30077
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
According to issue tracker b:119238959 #4 & #6.
Hardware modify design to make GPP_E3 to be a switch of touchscreen
I2C CLK and SDA.
Control GPP_E3 to make touchscreen I2C CLK and SDA keep low during
power on initialization to avoid data transfer during this time.
After touchscreen IC initial complete, control GPP_E3 to high to
make touchscreen I2C CLK and SDA work normally.
Depending on touchscreen IC specification, device take 105ms for
power on initialization.
Change delay time from 120ms to 105ms.
BUG=b:119238959
BRANCH=firmware-rammus-11275.B
TEST=emerge-rammus coreboot chromeos-ec chromeos-bootimage
Flash FW to DUT, run S5 stress test and verify the result
Signed-off-by: YanRu Chen <kane_chen@pegatron.corp-partner.google.com>
Change-Id: I86452c1445243c499aeaf931dba286db169c5628
Reviewed-on: https://review.coreboot.org/c/30180
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch incorporates following changes to enable console on UART0
1. update default console number to 0
2. Enable PCI port for UART0
GPIO configuration will be done by coreboot based on correct console
number.
Change-Id: I735d33674b276b28e2cbb753d3a6d83edbabe89d
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/30424
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Platforms moved to POSTCAR_STAGE so these are no longer used.
Change-Id: I9a7b5a1f29b402d0e996f2c2f8c6db3800cdddf3
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30387
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This patch modifies the hatch flash layout to support
IFWI 1.6 with the following regions,
Flash Region 0: Descriptor
[0x0 - 0xFFF]
Flash Region 1: IFWI (consist of ME and PMC FW)
[0x1000 - 0x3FFFFF]
Flash Region 2: BIOS
[0x1400000 - 0x1FFFFFF]
Change-Id: I3d05fb50e970737a2552b85d6aebed943bf2b6cb
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/30413
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Platform has been moved to C_ENVIRONMENT_BOOTBLOCK and this
file was for romcc bootblock.
Change-Id: I2c249b18edd41c9a7798400d24b1c9228422d59b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30391
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
This mainboard has the BSEL straps hooked up to the SuperIO
similar to the ASUS P5GC-MX and might therefore require a restart.
Tested:
- FSB 800, 1067 and 1333MHz CPUs
- USB
- Ethernet
- Serial
- 2 DIMM slots
- SATA
- Libgfxinit (VGA)
TESTED with SeaBIOS (sercon disabled) and Linux 4.19.
Change-Id: Id845289081751ff8900e366592745f16d96f07c0
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30250
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Any board that uses the AST driver will have support for native graphics
init. So, select the option in the driver instead of every board.
Change-Id: I2bf42c168d1ffdda11857854889b74953abd7e40
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/c/30355
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Fix the following warning shown in dmesg:
"ACPI BIOS Warning (bug): Incorrect checksum in table [FACP]"
The table checksum was wrong as it was calculated twice and with the second
time the checksum field wasn't set to zero.
Change-Id: I375354bf3e95ebdac3b0dad43659d72c6ab3175a
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/30353
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jay Talbott <JayTalbott@sysproconsulting.com>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Remove all cases in code where we tested for
EARLY_CBMEM_INIT or LATE_CBMEM_INIT being set.
This also removes all references to LATE_CBMEM_INIT
in comments.
Change-Id: I4e47fb5c8a947d268f4840cfb9c0d3596fb9ab39
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/26827
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Migration of globals is not needed as there is no real CAR that
gets torn down.
Change-Id: Id24642b49fab811e59291747eda8632cd49d83d0
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30346
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
This reverts commit a914152fa6.
Reason for revert:
According to the partner on this project, custom values like this
are no longer necessary.
Change-Id: I393eb4997f58abe0f77161999474994f06741519
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/c/30347
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
WWAN chip support 3 interfaces as pci express, USB 2.0 and USB 3.0, the
usgae of Sarien choose to only use USB interface but not over pci
express, so totally disable pci express root port 12.
BUG=b:1246720
TEST=Boot up into OS with WWAN attached, cold boot and warm boot 10
cyles can still device can be listed under lsusb.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: Ic4da393c0c0d903848111e1c037c2730c86afa7d
Reviewed-on: https://review.coreboot.org/c/30350
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Report correct board information for Whiskeylake RVP to OS.
Use short board name like other RVP as it's used
for firmware version check in auto test.
Change-Id: I3f7c95f136e39b978a335cc7855cac819043db7c
Signed-off-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-on: https://review.coreboot.org/c/30318
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Boon Tiong Teo <boon.tiong.teo@intel.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Some boards may want to initialize watchdog in verstage instead of
bootblock or ramstage, so we need to add watchdog support in verstage.
BRANCH=none
BUG=b:120588396
TEST=build successfully
Change-Id: I13ab84f54d576a0e8c723070b5d9aadd9d63f87c
Signed-off-by: You-Cheng Syu <youcheng@google.com>
Reviewed-on: https://review.coreboot.org/c/30329
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Refactor function mtk_spi_set_gpio_pinmux to reduce compiled code size.
This change can save us about 552 bytes (before compression).
Idea from Julius's comment in https://review.coreboot.org/c/coreboot/+/27498/4
BRANCH=none
BUG=b:120588396
TEST=manually boot into kernel
Change-Id: I93bc88c535b6a2ff94e85f247cf2d51f60b9b29c
Signed-off-by: You-Cheng Syu <youcheng@google.com>
Reviewed-on: https://review.coreboot.org/c/30328
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Updates to current master.
This includes:
- A fix for textmode scaling on G45
- Refactor things to rely less on inline proving
- Increased width of modeline fields to 32 bits
Change-Id: Iab2915b747f6e4fa4e78eb28fea29bb3a9b3b687
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/30311
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
These chips are still using LATE_CBMEM which was agreed upon to
be removed after release 4.7. It is now more than 1 year later
and they still linger around.
The work and review to bring this code up to date can happen on
the 4.9 branch and then squashed together and merged back into
mainline when done.
Change-Id: I11290a5e92397b9b7e7e5a19b029278e728671a3
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30326
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Nico Huber <nico.h@gmx.de>
These boards are still using LATE_CBMEM which was agreed upon to
be removed after release 4.7. It is now more than 1 year later
and they still linger around.
The work and review to bring those boards up to date can happen on the 4.9
branch and then squashed and merged back into mainline when done.
Change-Id: Iede79ef50681f769a47ce3d66b335dae92aef56b
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30325
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Newer CPUs/SoCs need to configure other features via the
IA32_FEATURE_CONTROL msr, such as SGX, which cannot be done if the
msr is already locked. Create separate functions for setting the
vmx flag and lock bit, and rename existing function to indicate that
the lock bit will be set in addition to vmx flag (per Kconfig).
This will allow Skylake/Kabylake (and others?) to use the common
VMX code without breaking SGX, while ensuring no change in functionality
to existing platforms which current set both together.
Test: build/boot each affected platform, ensure no change in functionality
Change-Id: Iee772fe87306b4729ca012cef8640d3858e2cb06
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30229
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: David Guckian
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This reverts commit 999b916015.
The DMIC doesn't have an ACPI id. The patch which enables ACPI
device with id DMIC may create conflict in the feature. Also the
ACPI id "DMIC" doesn't comply with ACPI naming conventions. The
issue for which the patch was introduced, is already addressed in
kernel DMIC driver and the patches are upstreamed in to the Linux
kernel.
Change-Id: I42cb076700dcb5906599471bebfcd5b265b17644
Signed-off-by: Jenny TC <jenny.tc@intel.com>
Reviewed-on: https://review.coreboot.org/c/30151
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
disable_all_smi_status() was not clearing SMI_EVENT_STATUS. This caused
us to complain in the eventlog (ELOG_SLEEP_PENDING_GPE0_WAKE) and then
wake early from sleep when waiting for a cr50 reset to turn on a cr50
update.
BUG=b:121203745
TEST=Careena remains in S5 until cr50 reset after cr50 update, and
ELOG_SLEEP_PENDING_GPE0_WAKE is no longer seen in eventlog.
Change-Id: I2eec014109249d5c3574c4dbdec5569e2a0bfc8e
Signed-off-by: Edward Hill <ecgh@chromium.org>
Reviewed-on: https://review.coreboot.org/c/30304
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Sometimes the platform boots in an invalid state, that will cause
FSP-M to fail. As a board_reset() doesn't fix it, issue an full_reset()
as soon as the IA32_FEATURE_CONTROL MSR is locked at beging of romstage.
Tested on wedge100s. After full reset the system behaves as normal.
Change-Id: I1a382b8fb650311b0c24b48e0986d22edfa2d261
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/30290
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Turn on power optimizer of PCH side DMI and SATA controller.
BUG=N/A
TEST=Build and boot up into sarien platoform, able to finish 100 cycles
of s0ix.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I41da2b4106d683945cdc296e2a77311176144f43
Reviewed-on: https://review.coreboot.org/c/30212
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Expose the FSP interface to enable SATA and PCH side DMI power optimize
options. Actual step executed in FSP, step defined in cannonlake pch
BIOS spec(CDI# 570374).
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: Ic0c589bb21e56800090bc0c75a0256a0409efc78
Reviewed-on: https://review.coreboot.org/c/30211
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
SaGv(system Agent Dynamic Frequency) have 4 settings
Disabled, Fixedlow, Fixedhigh, Enabled.
This patch add all 4 settings in enum definition and
used in devicetree.
BUG=None
Signed-off-by: Praveen hodagatta pranesh <praveenx.hodagatta.pranesh@intel.com>
Change-Id: I8f3b56f4d2bea1836373cc505ef5147144100b95
Reviewed-on: https://review.coreboot.org/c/30305
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Set CONFIG_NO_FADT_8042 to avoid probing for the 8042 controller.
This speeds up boot on nocturne by 1.3 seconds:
Before change:
[2.162266] EXT4-fs (mmcblk0p3): mounting ext2 file system using
the ext4 subsystem
After change:
[0.867735] EXT4-fs (mmcblk0p3): mounting ext2 file system using
the ext4 subsystem
BUG=b:120960844
BRANCH=none
TEST=build, flash, and boot nocturne; check dmesg to verify that
boot is faster and that you don't see the following log in dmesg:
[0.671501] i8042: Probing ports directly.
Change-Id: I62a16e6de5e74fa17970d9967f6d1628497ec1d3
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/30283
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The TXE PCI device serves no function under Linux, and doesn't
work properly under Windows, so disable/hide it from the OS.
Test: Boot Windows 10 on google/squawks, verify TXE not visible
under Device Manager.
Change-Id: Idaa152e15106b826fd5aa787090acd45719f4228
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30235
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Commit 73b723d [google/cyan: Switch Touchpad and Touchscreen...]
in additon to changing the touchpad/touchscreen interrupts from
edge to level triggered, also marked them as maskable. This not only
broke the touchpad functionality, but caused issues with the touchpad
as well. Revert the touchpad to being non_maskable for all cyan
variants with a touchscreen.
Test: boot GalliumOS on google/cyan with a range of kernel versions
(4.15.18, 4.16.13, 4.17.x, 4.18.x) and verify touchscreen functional,
touchpad working properly (not jittery)
Change-Id: I0e0357912f9404af7d0f4e7938a1a94c74810b37
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30236
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This board doesn't have a UART on the super I/O. Selecting this option
speeds up boot time from ~493 ms to ~416 ms.
Change-Id: I1d84f373831381da79022638e1082adf68f47aad
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/c/30148
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Quoting from the RISC-V Privileged Architecture manual version 1.10,
chapter 3.1.11:
The FS and XS fields use the same status encoding as shown in Table
3.3, with the four possible status values being Off, Initial, Clean,
and Dirty.
Status FS Meaning XS Meaning
0 Off All off
1 Initial None dirty of clean, some on
2 Clean None dirty, some clean
3 Dirty Some dirty
Change-Id: If0225044ed52215ce64ea979d120014e02d4ce37
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/c/28987
Reviewed-by: Philipp Hug <philipp@hug.cx>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
When I debug with HiFive Unleashed, I found that hart 4 could not be
running. Then find the duplicate MAX_CPUS definition. The correct
MAX_CPUS is located in src/soc/sifive/fu540/Kconfig
Change-Id: I583f6ba548daeeb6c7e341dc3fa8817e7dec5697
Signed-off-by: Xiang Wang <wxjstz@126.com>
Reviewed-on: https://review.coreboot.org/c/30179
Reviewed-by: Philipp Hug <philipp@hug.cx>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The following was tested:
- Using two DDR2 DIMMs
- S3 sleep and resume (on SeaBIOS it needs sercon disabled)
- Ethernet NIC
- Libgfxinit (native res and textmode)
- SATA
- USB
- 800MHz FSB CPU (Pentium(R) E5200 @ 2.50GHz)
- PS2 Keyboard
- Serial output
TODO:
- Add ACPI code for SuperIO devices (done in a follow-up patch)
- Add documentation
TESTED with SeaBIOS (sercon disabled), Linux 4.19
Change-Id: I483e1143e4095b8a58fed142d31ca7f233a854e2
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30239
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There are no public datasheets for this SuperIO. The results are from probing
the registers manually.
Change-Id: Ie5659533c5f224603f918d17942a7057e6701222
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30238
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Commit c37b0e3 [soc/intel/skylake: Generate ACPI DMAR table]
only generates DMAR tables for boards using FSP 2.0, which
leaves out Skylake Chromebooks, which use FSP 1.1.
Correct this omission by adding the same functionality for
FSP 1.1 boards.
Test: build/boot on U-series Skylake Chromebook, observe
IOMMU fully functional with intel_iommu=on kernel parameter.
Change-Id: I68837f58aac357fa3f58979fe92d8993fae58640
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30230
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
FSP support two SATA modes as AHCI mode (0) and RAID mode (1), make it
more clear in header file.
Change-Id: I1edcadc0048df839da145260b60f9f7720d981fe
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/30093
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
CPU ratio will be fixed to non-turbo max value if CpuRatio UPD had been
set to zero.
BUG=N/A
TEST=Boot up into sarien system, cat /proc/cpuinfo and cpu frequency is
changing.
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Change-Id: I3e82293c8b6027ddf9a528d0654fe46f233dcb82
Reviewed-on: https://review.coreboot.org/c/30216
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
When I added the cmos.layout file, I did not realise that the
southbridge code cleverly emulated the "keep state" option.
Tested on an ASRock H81M-HDS. The `Keep` option works as it should.
Change-Id: I908e59d1e1eedefa6610e7f980afc3c04390a519
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/c/30102
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
The deleted line crept in with commit 562db3bb3f ("libpayload: find
source of input characters").
Tested on an ASRock H81M-HDS with `power_on_after_fail` set to `Disable`
via CMOS. After this patch, the system no longer powers on as soon as
power is restored after a power failure.
Change-Id: Ie9d9dab9885b285db1c5094c2c8d62aae551f1e7
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/c/30101
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
RAM is reserved for Chromeos even when Chrome is not used.
Use CONFIG_CHROMEOS to determine if RAM must be reserved.
BUG=N/A
TEST=Intel CherryHill CRB
Change-Id: I3f55bf96ab2ec66cddbb54de03455a9bfd194682
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/29332
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
CONFIG_MAINBOARD_PART_NUMBER sometimes contains spaces, but spaces
inside compat strings aren't nice, so let's convert all spaces to
dashes.
Change-Id: I46f2b2d7091782e04df5476e50698001511f664b
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/c/30173
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
The previous settings caused the I2C frequency for the audio bus to be
too high, at 417kHz. The settings in this commit correct the frequency
to 396kHz.
BUG=b:119423345
Change-Id: Ibed886e6e1b0df4df6b87f6291e515364b3bf718
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Reviewed-on: https://review.coreboot.org/c/30129
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
commit msg copied from
commit id: 64c9f1584c
The GPIO drivers in Windows and Linux for the Icelake CPU
have a sparse GPIO map and do not allocate pins contiguously.
Each GPIO group is allocated as 32 pads regardless of whether
the hardware actually has that many in the group.
It appears this originated with a bug in Windows/UEFI and was
carried over to Linux in order to work with existing firmware:
https://lore.kernel.org/patchwork/patch/855244/
In order to support using ACPI GPIOs it is necessary for coreboot
to be compatible with this implementation. The GPIO groups that
are usable by the OS are declared with a pad base which is then
used to compute the number for ACPI GPIOs.
Change-Id: I94fafd8af13cf229f5c467de5179aed021465739
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/30276
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
This reverts commit ad41f55123.
Reason for revert: <Issue have seen on EVT platform that vboot always fail to verify keyblock A>
BUG=b:121169122
Change-Id: I2790ef3463a228008b614498009fbdc8b493cfb0
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/30286
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
When the BMC firmware module is installed on the KGPE-D16, the
RAM SPD multiplexer lines are disconnected by hardware from the
SP5100 GPIOs and attached to BMC GPIO lines instead.
Set the BMC GPIOs to match the state of the SP5100 GPIOs during
RAM setup.
Change-Id: Ia251334ae44668c2260d8d2e816f85f1f62faac5
Signed-off-by: Timothy Pearson <tpearson@raptorengineering.com>
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/19820
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
The device ID is documented in "Intel Xeon Processor E3-1200 v3
Product Family Datasheet volume 2" section 2.2.
Tested with ASRock H81M-HDS with Xeon E3-1271 v3. SeaBIOS payload can
find the boot devices, and GRUB payload can boot Debian GNU/Linux on
the SATA disk.
Change-Id: I999391c9bbc6b39526ad7aec8a6d8fe1a9b5f921
Signed-off-by: Iru Cai <mytbk920423@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30266
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
The Intel GMA ACPI opregion address needs to be set on S3 resume,
otherwise the Windows display driver fails to re-initialize correctly.
Fix by ensuring the address is set correctly regardless of display
init type used (GOP or VBIOS).
Test: build/boot on google/edgar, ensure internal display functional
following S3 resume under Windows 10.
Change-Id: I471c44e8ba4514e4a2ddf6739109b759145598ed
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30233
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Mirrors addition to Braswell SoC in commit d3d0f07.
Test: build/boot Windows 10 on Baytrail ChromeOS device, verify Windows shows
virtualization as enabled.
Change-Id: Ia1fafa73325814fed30b2ac91290b682dd8eab04
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30228
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Commit d80884ea5a ("mb/google/kahlee: Disable IOMMU") disabled the IOMMU
in all kahlee variants, but omitted the explaining comment only in
liara's devicetree.cb. Copy this comment to liara.
Change-Id: I564013a16217445003467e2a0579abd50597b205
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/c/30166
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
They are hopefully stable enough by now.
TEST=Building with for emulation/spike-riscv with BUILD_TIMELESS,
with and without this patch, results in the same coreboot.rom.
Change-Id: Ie6747c7eeea6cd8fd2138c5ba535a08c5add9038
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/c/30164
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Philipp Hug <philipp@hug.cx>
Using ${...} in some places is slightly confusing.
Fixes: 395cbb4f97 ("mb/*/*/Kconfig: Use CONFIG_VARIANT_DIR for devicetree")
Change-Id: Id0856a10d92786a41d45ca697945699f6f4c1f4c
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/c/30163
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Bobba would prefer to use different SAR values per sku-id for regulatory
compliance. This commit uses the newly added interface for custom wifi
SAR CBFS filenames.
CQ-DEPEND=CL:*729429
BUG=b:120958726
BRANCH=octopus
TEST=build
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Change-Id: I354382d651d65d533459f0ca460ca6fd6de547fd
Reviewed-on: https://review.coreboot.org/c/30223
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Using a fixed filename only allows for one SAR configuration to be
checked into CBFS. However, we have devices with shared firmware that
would desire separate SAR configurations. This change allows boards to
define a function to select one of multiple files stored in CBFS to be
used.
BUG=b:120958726
BRANCH=octopus
TEST=build
Signed-off-by: Justin TerAvest <teravest@chromium.org>
Change-Id: Ib852aaaff39f1e9149fa43bf8dc25b2400737ea5
Reviewed-on: https://review.coreboot.org/c/30222
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
It seems they are not included anywhere, Jenkins?
Change-Id: I629cdeb337fce381c69bd1ba0520e524ccdd90dd
Signed-off-by: Nico Huber <nico.h@gmx.de>
Reviewed-on: https://review.coreboot.org/c/26756
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
According to bard/ekko cpu types, PL2 need to set the values
1. KBL_U PL2 is 25w.
2. KBL_R PL2 is 29w.
BUG=b:120874861
TEST=power on and check the DUT can boot up well
Change-Id: I5f9d672c4244c363a7cfb362653663a065259fc0
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30178
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Enaebl the RTC driver to be used on mc_apl4.
Change-Id: Ib8d2a9f6b8cea47cd10db4dfcc59eec1b21c7993
Signed-off-by: Uwe Poeche <uwe.poeche@siemens.com>
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/30205
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
This function returns APIC id for respective cpu core.
BUG=b:74436746
BRANCH=none
TEST=mp_get_apic_id() can be accessed in other files now.
Change-Id: I5c5eda8325f941ab84d8a3fe0dae64be71c44855
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/25620
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch implements board reset on the Cheza board. The real board
reset used by the operating system uses the PMIC, but unfortunately the
PMIC needs to be configured right for that to work. The PMIC
configuration currently happens in the Qualcomm blob (QcLib) that is run
from romstage, but vboot needs to be able to reboot during verstage
already. Porting all the PMIC initialization code to run in the
bootblock seems excessive (and at odds with the goal of doing as little
as possible before verification), so we'll just do a little hack and ask
the EC to perform a cold reset instead. For vboot purposes, this should
work just as well.
BUG=b:118501305
TEST=Hacked vboot code to call vboot_reboot(), confirmed that board
reset and came back up as expected.
Change-Id: I3858d95f481884a87c243d4fa3d6369c1e8a5a2c
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-on: https://review.coreboot.org/c/29849
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The GPIO pin map for CNL-H does not match with the OS expected
pin numbers. This has been updated to match what is used by the
Linux kernel pinctrl driver and the pad base has been set for
the GPIO groups to match the sparse GPIO map used by the kernel.
I do not have CNL-H hardware to test this so it is verified against
the kernel driver at drivers/pinctrl/intel/pinctrl-cannonlake.c
Change-Id: Ife7d3090d654b0b88c6911befa08bf6abd4f2ff9
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30134
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The GPIO drivers in Windows and Linux for the Cannonlake CPU
have a sparse GPIO map and do not allocate pins contiguously.
Each GPIO group is allocated as 32 pads regardless of whether
the hardware actually has that many in the group.
It appears this originated with a bug in Windows/UEFI and was
carried over to Linux in order to work with existing firmware:
https://lore.kernel.org/patchwork/patch/855244/
In order to support using ACPI GPIOs it is necessary for coreboot
to be compatible with this implementation. The GPIO groups that
are usable by the OS are declared with a pad base which is then
used to compute the number for ACPI GPIOs.
BUG=b:120686247
TEST=tested with write protect GPIO on sarien board. Before this
change the ACPI pin number was 220 which did not correspond to the
pin number in Linux. After this change the ACPI number is 303,
which maps to the correct GPIO in Linux. Now the GPIO value reported
by the kernel changes when the WP pin is toggled in hardware.
Change-Id: I4f1a9e118d7e48f2445ccbb62a12a22e9a832c51
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30133
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
If the generic GPIO library is enabled the code that generates the
GPIO table in ACPI should attempt to get the GPIO pin value from
the gpio_acpi_pin() function.
BUG=b:120686247
TEST=Tested on Sarien board to ensure that GPIO pin exported by
Chrome OS for the Write Protect signal is correct.
Change-Id: I267694b576009f79bacac6eda5f32bbf51742d78
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30132
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
In some situations the GPIO pad numbers used by the OS are not
contiguous and coreboot must provide a way for ACPI to provide
the expected GPIO number to the OS.
To do this each GPIO group can now have a pad base value, which
will be used as the starting pin number for this group and it
is added to the relative pin number of this GPIO to compute the
ACPI pin number for a particular GPIO.
By default this change has no effect because the existing uses
of INTEL_GPP() will set the pad base to PAD_BASE_NONE and the
GPIO number is used as the ACPI pin number without translation.
BUG=b:120686247
TEST=tested on a sarien(cannonlake) board
Change-Id: I25f73df45ffae18c5721a00ca230a6b07c250bab
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30131
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Correct Ram_ID=0b0000 SPD Module Part Number mismatch last alphabet 'C'
to "H5AN8G6NAFR-UHC".
BUG=b:120000816
BRANCH=master
TEST=mosys memory spd print all
Change-Id: I4f4b83589ad6b53c0a24f2637f0fe8b92a1168e3
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30208
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Correct to add Ram_ID=0b0001 SPD Module Part Number mismatch last alphabet 'C'
to "H5ANAG6NAMR-UHC".
BUG=b:120000816
BRANCH=master
TEST=mosys memory spd print all
Change-Id: I4d320b2e10c4865456a9a9ccb400db5dd9256b3e
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30177
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch introduces 3 helper function for cpuid(1) :
1. cpu_get_cpuid() -> to get processor id (from cpuid.eax)
2. cpu_get_feature_flags_ecx -> to get processor feature flag (from cpuid.ecx)
3. cpu_get_feature_flags_edx -> to get processor feature flag (from cpuid.edx)
Above 3 helper functions are targeted to replace majority of cpuid(1)
references.
Change-Id: Ib96a7c79dadb1feff0b8d58aa408b355fbb3bc50
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/30123
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Creating skeleton files and directories in mainboard for the new Hatch
board. This is to facilitate development for different parties
involved.
BUG=None
BRANCH=None
TEST=./util/abuild/abuild -p none -t google/hatch -x -a
Change-Id: I5fc60c178f83034abe5d846d0f4169072b66f448
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/30169
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Change-Id: I64e79904c7ad95091ea29d9f80444c4e3b493471
Signed-off-by: T Michael Turney <mturney@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/29298
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Update the TRACKPAD_INT1_1V8_ODL GPIO configuration so that it acts as a
wakeup source
BUG=b:119598593
BRANCH=octopus
TEST=Ensure that the system wakes up on trackpad events. Ensure that the
suspend_stress_test runs successfully for 25 iterations.
Change-Id: I28292682cf9c8037abb87d265e49a60139550db2
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/30171
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Change-Id: I15cfbbab15b940641c3952f2cfb4b11c37574816
Signed-off-by: T Michael Turney <mturney@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/29299
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Disable SATA port 0 and port 1 as that's not used as SATA on platform.
BUG=N/A
TEST=Build and boot up fine on google arcada board.
Change-Id: I1b8801f7a0f9b7847b85d7c315fa0a2093b32f70
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/30091
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Roy Mingi Park <roy.mingi.park@intel.com>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
There are 2 vendor BIOS's for the Lenovo X200 with the difference being the
settings in the VBT blob to accommodate different backlight frequencies.
Linux however sticks with the setting set by the firmware.
Tested on Lenovo X200 with CCFL backlight.
Change-Id: I4c4a7011ce03cdd511fa2e2160c2f006ba2707ba
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/29904
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
PEN_EJECT GPIOs are active high and also require an internal pull-up.
Update the GPIO configuration appropriately.
BRANCH=octopus
BUG=b:117953118
TEST=Ensure that the system boots to ChromeOS. Ensure that the stylus
tools open on pen eject. Ensure that the system can enter S0ix and S3
states successfully when the pen is inserted. Ensure that the system
wakes on Pen Eject. Ensure that the system does not enter S0ix and S3
states when the pen is placed in its holder. Ensure that the
suspend_stress_test runs successfully for 25 iterations with the pen
placed in its holder.
Change-Id: Ibf9cb214a8ce7561efbb77a7e99d1e386cf064c3
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/30107
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add mechanism to configure GPE wake event which in turn can be used as ACPI
Power Resources for Wake
BRANCH=octopus
BUG=b:117953118
TEST=Ensure that the wake GPE event is added to ACPI Power Resource for
Wake.
Change-Id: Iacc12b8636aaac98a8689a211cbe1dcfe306f342
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/30106
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Update the GPIOs for the next board build. Mostly minor changes but
the polarity change on GPP_E8/RECOVERY on sarien will result in it
booting to recovery every time unless using new hardware.
For this reason the recovery mode GPIO that is passed to vboot is
commented out for sarien. It is only used for testing and currently
it is useful to have an image that works on both board versions.
Change-Id: I32d84f3010cb4d3968370a03f7e191b1710a50e8
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30062
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently CoffeeLake FSP is incorrectly modifying GPIO pad configuration
if specific UPD variables are not set as it expects.
This affects the display-related SOC pads with the following UPD variables:
UINT8 DdiPortBHpd; // GPP_E13
UINT8 DdiPortCHpd; // GPP_E14
UINT8 DdiPortDHpd; // GPP_E15
UINT8 DdiPortFHpd; // GPP_E16
UINT8 DdiPortBDdc; // GPP_E18/GPP_E19
UINT8 DdiPortCDdc; // GPP_E20/GPP_E21
UINT8 DdiPortDDdc; // GPP_E22/GPP_E23
UINT8 DdiPortFDdc; // GPP_H16/GPP_H17
Until FSP is fixed to not touch the pad configuration this workaround
will reprogram the GPIO settings after FSP-S step so they are correct
when the OS attempts to use them.
This was found in CoffeLake FSP Gold release:
https://github.com/IntelFsp/FSP/tree/master/CoffeeLakeFspBinPkg
As well as the current top-of-tree for the FSP sources.
BUG=b:120686247,chromium:913216
TEST=verify correct GPIO configuration for GPP_E group in the kernel
Change-Id: I19550c4347cf65d409de6a8638619270372c4d0a
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30113
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The kernel GPIO driver only expects some GPIO communities to be exported
in the _CRS and it will not work correctly if the other communities are
exported.
CNL-LP: GPIO communities 0, 1, 4
CNL-H: GPIO communities 0, 1, 3, 4
Additionally one of the pin offset values was incorrect in GPIO
community 1 for CNL-LP. This doesn't have any specific failure mode but
it was found when auditing the GPIO code.
Details of the kernel expected map can be found in the linux kernel at
drivers/pinctrl/intel/pinctrl-cannonlake.c
BUG=b:120686247
TEST=check /sys/kernel/debug/pinctrl/INT34BB:00/pins to ensure that
pins >= 198 are not reading all zeros for the pin config registers.
Change-Id: Ie1a2f3b9f9f4b24a9fc57e468dee50e99753912f
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30112
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Synaptics Trackpad wake event is incorrectly routed to GPE0_DW2_02. The
concerned GPIO is not connected and hence wont trigger a wakeup. Fix the
GPE wake configuration for synaptics trackpad.
BUG=b:120666158
BRANCH=octopus
TEST=Ensure that the wake on trackpad works with Synaptics touch pad.
Ensure that the system can enter S0ix successfully(run
suspend_stress_test -c 25).
Change-Id: I87b8c266266280f61700839d428e6f8938b0f72f
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/30105
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
FSP defined a special clock source usage 0x70 for PCH LAN device, update
that to google sarien platform.
BUG=b:120003760
TEST=Boot up into OS, ethernet able to be listed in ifconfig.
Change-Id: I9f945be4f0ce15470ab53f44e60143f3fd0fddf8
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/30100
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Part Number
Correct Ram_ID=0b0011 SPD Module Part Number to "MT40A1G16KNR-075:E" from
"4ATS1G64HZ-2G6E1".
BUG=b:120000816
BRANCH=master
TEST=mosys memory spd print all
Change-Id: I9d582b3753de9a48865eb6eca7e4fbdb31b799ff
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30049
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Number
Correct Ram_ID=0b0000 SPD Module Part Number to "H5AN8G6NAFR-UH" from
"HMA851S6AFR6N-UH".
BUG=b:120000816
BRANCH=master
TEST=mosys memory spd print all
Change-Id: I1f6e885638589a35334a9a8f905af4877c5d1f91
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30048
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Part Number
Correct Ram_ID=0b0010 SPD Module Part Number to "MT40A512M16JY-083E:B"
from "4ATF51264HZ-2G3B2".
BUG=b:120000816
BRANCH=master
TEST=mosys memory spd print all
Change-Id: I6847a55968260cdbc1588ddeb8d23c515ad87920
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30050
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
The Intel Sensor Hub was enabled on the wrong variant so this change
moves the enable from sarien to arcada.
Change-Id: If933623f7dbb45c4805fb61430465236eca19ee8
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30070
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Li1 Feng <li1.feng@intel.com>
Reviewed-by: Jett Rink <jettrink@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
A new liara specific VBIOS updating eDP power sequence is available now,
Change Kconfig to use it if board is google liara.
BUG=b:120534087
TEST=Build liara, booted, tested eDP test compliance.
Change-Id: I444cfa0bd755480e006f11c0d692b25b96129c29
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/c/30090
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Recently there has been a change to print ME version. But the stage at
which the version is printed causes the HECI device to remain in D0 state.
This in turn prevents the SoC from entering S0ix state.
This change moves printing ME version a little earlier so that the HECI
device is put into D0i3 state by FSP and the SoC can enter S0ix state
successfully.
BRANCH=octopus
BUG=b:120571529
TEST=Ensure that the ME version gets printed in BIOS logs. Ensure that
the device boots to ChromeOS. Ensure that the device enters S0ix
successfully(using suspend_stress_test -c 25).
Change-Id: I85bc45003a040c8347f929457792d78a9a077c6c
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/30074
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Use CONFIG_CPU_MAX which defaults to 1 instead of CONFIG_RISCV_HART_NUM.
The default value of CONFIG_RISCV_HART_NUM was 0 and cause a jump to address 0.
Add a die() call to fail gracefully.
Change-Id: I4e3aa09b787ae0f26a4aae375f4e5fcd745a0a1e
Signed-off-by: Philipp Hug <philipp@hug.cx>
Reviewed-on: https://review.coreboot.org/c/29993
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Xiang Wang <wxjstz@126.com>
Reviewed-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Correct a build error that occurs when HUDSON_UART is selected.
Replace sizeof() of a nonexistent variable with the intended type.
This was introduced in
bd48b23 "southbridge//hudson: Get rid of void pointer math".
BUG=b:118484178
TEST=Build Bettong with Chipset/"UART controller for Kern"
Change-Id: Icc0ff9d80c3f5cab9ab837cf1cd0cd8eb0753284
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30072
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
The code annotated by the comment is dealing with root port 7, so update
the comment to reflect that. It looks like the comment was copied from
the root port 3 case, but not updated.
Change-Id: I0e27e4453f4c3b2b1b9dffb0c89b71373c6b303e
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/c/30078
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The code is based on autoport and that for T430s
Tested:
- CPU i5-3337U
- Slotted DIMM 2GiB
- Soldered RAM 4GiB from samsung (There may be more models here)
- Camera
- pci-e and usb2 on M.2 slot with A key for wlan
- sata and usb2 (no superspeed components) on M.2 slot with B key for wwan
- On board SDHCI connected to pci-e
- USB3 ports
- libgfxinit-based graphic init
- NVRAM options for North and South bridges
- Sound
- Thinkpad EC
- S3
- TPM1 on LPC
- EHCI debug on SSP2 (USB3 port on the left)
- Linux 4.9.110-3 within Debian GNU/Linux stable, loaded from
Linux payload (Heads), Seabios may also work.
Not tested:
- Fingerprint reader on USB2 (not present on mine)
- Keyboard backlight (not present on mine)
- "sticky_fn" flag in nvram
Not implemented yet:
- Fn locking in nvram (may not be identical to "sticky_fn")
- C-based native graphic init (since T431s has eDP instead of LVDS)
- Detecting the model of Soldered RAM at runtime, and loading the
corresponding SPD datum (3 observed) from CBFS (the mechanism may be
similar to that on x1_carbon_gen1 and s230u, but I do not know how
to find gpio ports for that, and SPD data stored in vendor firmware.)
Change-Id: Ic8062cacf5e8232405bb5757e1b1d063541f354a
Signed-off-by: Bill XIE <persmule@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30021
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Provide rise/fall times as measured on existing boards. This will
need adjusted for new boards but provides a starting point that
makes I2C clocks look reasonable.
Tested by measuring I2C bus speed and rise/fall times with a scope.
Change-Id: Ic18010f5efc41dcee8925d696767ba2c44e3df4b
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30069
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Add an entry to the soc_clock table for a 216MHz clock so that
the I2C controller clock is calculated correctly when the I2C
bus is used in coreboot.
This was tested by measuring the I2C clock speed on H1 I2C bus
on a sarien board in coreboot and ensuring it is ~400KHz.
Change-Id: I6c3cacdad318a5ce41bc41e3ac81385c2d4f396c
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30068
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
The input clock for the I2C controllers was set at 133MHz but should
really be 216MHz according to the kernel:
https://patchwork.kernel.org/patch/10408729/
"Intel Cannon Lake PCH has much higher 216 MHz input clock to LPSS I2C
than Sunrisepoint which uses 120 MHz. Preliminary information was that
both share the same clock rate but actual silicon implements elevated
rate for better support for 3.4 MHz high-speed I2C."
This change was tested on a sarien board where an I2C trackpad that was
measuring ~700MHz on I2C and is now measuring ~380MHz.
Change-Id: I792d1f013da5538a2b8157e2f99b754ca7b6bf70
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30061
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Lijian Zhao <lijian.zhao@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
As part of the memory mapped BIOS region is covered by SRAM, check
that CBFS always fits the effectively mapped region of flash. This
is usually taken care of by reserving the SRAM range in the FMAP
(e.g. as BIOS_UNUSABLE), but can be missed.
Change-Id: If5a5b553ad4853723bf13349c809c4f6154aa5f2
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/30055
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Re-write the UAO handling code as it had stopped working (#171)
(the flag was not getting read from the RTC properly in SMM)
Remove the SMM code as it's not needed (but EC flag won't be set
upon entering S3 now)
Set the EC flags on boot the same way other flags are set
Document bitwise operators for clarity
Propagate changes to other Thinkpads
(updated X201 to have 2 bits for the flag as it only had 1)
Per Nicola Corna's previous commits, 0x0d is set for "AC only"
"AC only" does exhibit different behaviour - the USB port is
turned on a few seconds after entering S3, rather than < 1 sec,
regardless of AC status
Tested on X220
Change-Id: If812cd1ef8fb1a24d7fadbe834f574b40cbcd56a
Signed-off-by: Nathaniel Roach <nroach44@gmail.com>
Reviewed-on: https://review.coreboot.org/c/29565
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Tested - Lenovo t520 still builds fine with this patch.
Change-Id: I82492c071ca760f0790b992acbdb86021f470cfe
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30043
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Fix some compiler warnings due to pointer to integer conversions
with different size.
Required for 64bit ramstage.
Change-Id: Ibfb3cacf25adfb4a242d38e4ea290fdc3929a684
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/c/29875
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This is needed so the next patch can set up GPIOs before
AGESA runs.
BUG=b:120436919
TEST=Verified romstage mainboard code runs before AGESA
Change-Id: I76c035e166cd64382b52dff5ae00a6f115cbac9b
Signed-off-by: Martin Roth <martinroth@chromium.org>
Reviewed-on: https://review.coreboot.org/c/30038
Reviewed-by: Daniel Kurtz <djkurtz@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Platform have a 32MB SPI chip, so we can increase the bios region from
16MB to 28MB.
BUG=b:119267832
TEST=Build and boot fine on sarien platform.
Change-Id: I9bc0fa0f662e5ec64e77f2005dbb2e7edb8b2524
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/29945
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
AMD traditionally claims the resource at I/O port 61 for the onboard
PC-AT speaker. In later designs, the speaker may be omitted in favor
of routing the SPKR signal to the codec.
Some systems implement neither, and for those it is not correct to
identify the resource as a speaker. Modify the EISAID reported to
the OS depending on the system design. The default is that port 61
is reported as reserved. In order to report a speaker, add #define
in mainboard//dsdt.asl.
TEST=check /proc/ioports and iasl -d for both ways using a Grunt
BUG=b:117818432
Change-Id: I33aafb187f9fea7b38aae43c399292c7521fcfc4
Signed-off-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-on: https://review.coreboot.org/c/30037
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
When building grunt with flags set to detect variables that get a value but
then are unused, there are 5 instances that causes error (unused variable).
In most cases it's enough to simply remove the variable. Other instances,
is better to simply use the variables (one instance it's a return value, on
the other instance using the variables makes code more readable).
BUG=b:120260448
TEST=Build and boot grunt.
Change-Id: I0d00fb6a42db20afb34c76b9445a741a57096ead
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/c/29985
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Sort mainboard-specific defines in the same order as in all other Lenovo
boards. This is a purely cosmetic change which just makes diff between
boards smaller.
Change-Id: I4e379bb727b356fc6010e93de492f6d73f97a750
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/c/29544
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Most Lenovo mainboards define their own specific defines in dsdt.asl.
Let's make it consistent across all Lenovo mainboards.
Tested - builds fine.
Change-Id: I03fbeb09b25e42af2dfbb220c0f726e6abb73673
Signed-off-by: Peter Lemenkov <lemenkov@gmail.com>
Reviewed-on: https://review.coreboot.org/c/29543
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Now that all targets featuring these southbridges use SMM_TSEG these
files are unused.
Change-Id: Ic3a1d790f3595e98a8d33e6e8274cb72ad356a89
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30018
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
tlclk is not specific to the UART block in the FU540, so let's calculate
its frequency in clock.c.
Change-Id: I270920027f1132253e413a1bf9feb4fe279b651a
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/c/29335
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Philipp Hug <philipp@hug.cx>
This patch lets spike boot to "Payload not loaded" again.
Because soc/ucb/riscv/ does not represent a real SoC, but is a dummy
directory for emulators, and different emulators might have different
memory maps, I moved mtime_init to the mainboard-specific directories
for Spike and QEMU.
Change-Id: I080f7f81df752e25478bd277637bf894bbee4cb2
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/c/28873
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Hug <philipp@hug.cx>
Init SPI bus 0 to connect TPM, configure interrupt type of GPIO CR50_IRQ,
implement tis_plat_irq_status(), and set up chromeos GPIO table for TPM
interrupt.
BUG=b:80501386
BRANCH=none
Test=Boots correctly on Kukui.
Change-Id: Ieaa6ae65fbfb5ab6323e226e8171dd7a992c3a39
Signed-off-by: Tristan Shieh <tristan.shieh@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/29192
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Refactor GPIO EINT code which can be reused among similar SoCs.
BUG=b:80501386
BRANCH=none
TEST=emerge-elm coreboot; emerge-kukui coreboot
Change-Id: Ib01b43cf1aa4082d7d968fe1ef82f75e8cf05b8b
Signed-off-by: Chuanjia Liu <Chuanjia.Liu@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/29837
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Use common code to tear down CAR.
Change-Id: I62a70ae35fe92808f180f2b5f21c5899a96c2c16
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/29930
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch does the following:
- improve the style by removing tabs in front of jmp addresses
- Make the code for zeroing variable MTRR more readable (copied from
cpu/intel/car)
- Fetch PHYSMASK high from cpuid instead of Kconfig
Change-Id: I6ba67bb8b049c3f25b856f6ebb1399d275764f54
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/29928
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This does the following:
- Reuse the cpu/intel/car/non-evict CAR setup and exit.
- Use postcar_frame functions to set up the postcar frame
Change-Id: I428832a2d7e46ce61a7f9bd498b609feb4518eb0
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/29927
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Instead of SMMSTORE_APM_CNT use APM_CNT_SMMSTORE and define it in
cpu/x86/smm.h
Change-Id: Iabc0c9662284ed3ac2933001e64524011a5bf420
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/30023
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Instead of ELOG_GSMI_APM_CNT use APM_CNT_ELOG_GSMI and define it in
cpu/x86/smm.h
Change-Id: I3a3e2f823c91b475d1e15b8c20e9cf5f3fd9de83
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/30022
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use a raw fmap region SMMSTORE for the SMMSTORE mechanism, while
keeping the initial option to use a cbfsfile.
TESTED on Asus P5QC, (although it looks like the tianocore patches
using it might need some love as they can't seem to save properly).
Change-Id: I8c2b9b3a0ed16b2d37e6a97e33c671fb54df8de0
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/29991
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
We alwas define uint64_t as unsigned long long, even on x86_64.
Fix PRIu64 to match the definition of the datatype, to prevent
compilation errors when compiling for x86_64.
Change-Id: I7b10a18eab492f02d39fc2074b47f5fdc7209f3d
Signed-off-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-on: https://review.coreboot.org/c/30002
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Set GPIO D22 low to get WWAN_PERST#_R asserted.
BUG=N/A
TEST=Boot up with Arcada board, check WWAN get detected as USB devices
through lsusb command.
Change-Id: Ie848cd19fdf3b6c4b6abeb5fa3f566e5e4e7e928
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/30030
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Bora Guvendik <bora.guvendik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Cache BIOS region can boost boot performance, however it can't be over
16MB, according to processor EDS vol1(Apollolake/Skylake/WhiskeyLake),
FLASH+APIC LT will be less than 20MB under 4G. Set the maxiam to 16GB
to save numbers of mtrr entries.
BUG=b:119267832
TEST=Build and boot up fine on whiskeylake rvp platform.
Change-Id: I46a47c8bf66b14fb2fcb7b6b1d30d02886c450a4
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/29944
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add the USB device information for the sarien/arcada variants.
This includes the ACPI _PLD group definitions for the external
ports that indicate which USB2 and USB3 ports share the same
physical interface.
Change-Id: I0b936127954ba09c61ccb871bfc62ee7d99da263
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30000
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add ACPI _PLD group definitions for the external ports
that indicate which USB2 and USB3 ports share the same
physical interface.
Change-Id: I7f85720a878a3774d453a9adb82518722f7ba23d
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29999
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
The Linux kernel can use the ACPI _PLD group information to
determine peer ports. Currently to define the group information
the devicetree must provide a complete _PLD structure. This
change pulls the group information into a separate structure that
can be defined in devicetree. This makes it easier to set for
USB devices in devicetree that do not need a full custom PLD.
This was tested on a sarien board with the USB devices defined
by verifying that the USB 2/3 ports are correctly identified
with their peer in sysfs.
Change-Id: Ifd4cadf0f6c901eb3832ad4e1395904f99c2f5a0
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29998
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add the ACPI device names for the USB ports to match what
is in the DSDT so USB ports can be defined in the SSDT.
Change-Id: Ibb323bbd324811fa3178b0cba3d7f0a315169486
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29997
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Increase the bootblock size to 48K to match skylake. With UART
enabled we are very near the 32K limit, and with upcoming changes
to add USB devices in devicetree for a cannonlake board it is over
the current 32K limit.
Change-Id: I155cb0a6af1746af6833fa9f35c2ea6fe0bc709f
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29996
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Send the EC command required to turn the camera power on
and verify that it shows up on the USB bus.
Change-Id: I9e9ba712a11cef85cde91ac21a4b6b5090ef58dc
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29987
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Enable DPTF support for sarien/arcada boards. This is currently
using placeholder values that are identical that will be updated
after thermal tuning is done.
Change-Id: I7d51c3b38068fc25927c8dafc0bd9069b29d77f5
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29762
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
There is a dependency issue with the EC DPTF code accessing
methods that are external, but once the mainboard includes the
relevant code they become internal and the current version of
IASL used by jenkins will fail to compile it.
Until the new IASL is deployed everywhere wrap the EC DPTF code
and expect that the mainboard will explicitly enable it.
Change-Id: I612ad8f86d424060ca0303d267d7c2915c760173
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/30036
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add the support needed for DPTF. This includes the methods to
write trip point values, read temperatures, and handle events.
This was tested on a sarien board by inspecting AML debug output
with the kernel while monitoring temperatures and trip points in
sysfs and controlling temperatures with a fan to ensure that when
a trip point is crossed an SCI is generated and the event is
handled properly.
Change-Id: I8d8570d176c0896fa709a6c782b319f58d3c1e52
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29761
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
- Disable debug output from read/write methods by default
- Use argument to _REG to disable SCI when EC is unregistered
- Change read/write macros to sync level 2 so they can be called
when a mutex is already held
- Define some missing events
Change-Id: Ic65ebbb6a6151444c47b4aeff7429e186856c49a
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29760
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Define the constants that DPTF expects from the SOC in order to
use the common DPTF ACPI code. For cannonlake this indicates
the CPU device is called B0D4 and is at PCI address 00:04.0.
Change-Id: I43c2f8dd7281d3e9f791ab01478ee7823fd6b128
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29759
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add a method to convert from 1/10 Kelvin to Celsius. This
is useful for EC devices where the sensor temperature are
stored in Celsius instead of Kelvin.
Change-Id: I6b1154f5ba13416131a029966d6d5c1598904881
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29758
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In order to support using the common ACPI code on more platforms
than just Apollo Lake the DPTF code needs to be told what the
PCI address is for the CPU thermal device.
Change-Id: I638f2387330bbc42f64eb0fb676ee32c5df6572e
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29757
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Extended events will be handled by the OS kernel driver, but that
driver needs a method exposed by ACPI to read the event data from
the EC and into a buffer.
Tested by generating a hotkey event and reading the buffer from
the Linux kernel driver with acpi_evaluate_object().
Change-Id: Ic8510e38d777a5dd31a5237867313efefeb2b48e
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29674
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Add EC command to enable WiFi radio and send that command at
startup. Tested to ensure WiFi is functional on a sarien board.
Change-Id: Iac46895c7118567e1eb55ea33051a1662103b563
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29673
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable the COM1 ACPI device based on the existing Kconfig option
CONFIG_DRIVERS_UART_8250IO instead of expecting the mainboard to
also define another value for ACPI.
Change-Id: I69361cc2c245cfcad3e4f57567bf56d5a26f0b06
Signed-off-by: Duncan Laurie <dlaurie@google.com>
Reviewed-on: https://review.coreboot.org/c/29672
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Set WWAN_GPIO_PERST#(GPP_D22) to low at bootblock stage to meet
the logic output for WWAN_PERST#_R to high.
BUG=120004153
TEST=Boot up Sarien board, check WWAN get detected as USB
devices through lsusb.
Change-Id: I16f1101c64dfd4dcb5e8342fdb925951f6f2f90b
Signed-off-by: Amanda Huang <amanda_hwang@compal.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30017
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
The different PLLs in the fu540 use the same register layout, so use one
function (configure_pll) to program a PLL and wait for it to lock. This
also makes it possible to dynamically calculate the PLL settings later.
TEST=Boot until "Payload not loaded" on HiFive Unleashed
Change-Id: I5c0cee886bad5758c70f967d2bb998c1e1a736ab
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/c/29356
Reviewed-by: Philipp Hug <philipp@hug.cx>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
* Verify the flash write protection on each boot
* Program non-volatile write protection on first boot
Tested using I715791b8ae5d1db1ef587321ae5c9daa10eb7dbc.
The bootblock is write-protected as long as the #WP pin is asserted low:
* Reprogramming of the status register fails.
* Trying to write to WP_RO region fails.
Programming the WP_RO is only possible if #WP pin is high.
Change-Id: I6a940c69ecb1dfd9704b2101c263570bebc5540e
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/29532
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
The TB has to be inverted to actually protected the correct region.
Tested on elgon using I67eb4ee8e0ad297a8d1984d55102146688c291fc.
Change-Id: I715791b8ae5d1db1ef587321ae5c9daa10eb7dbc
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/30014
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-by: David Hendricks <david.hendricks@gmail.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
update the new sku ids of bard/ekko
BUG=b:120257865
BRANCH=Nami
TEST=emerge-nami coreboot chromeos-bootimage
write the new sku id in cbi and verify the fw to
check it can get the correct settings by the sku id
Change-Id: I3579d3d8042a270d8ea8e2f7b5612ff8e2cdfa7b
Signed-off-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/30031
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change enables mode change as a wake source from S3 and
S0ix. Thus, any time the device switches between clamshell and tablet
mode while it is suspended, it will be treated as a valid user event
and hence wake source.
BUG=b:120349473
BRANCH=octopus
TEST=Verified that octopus wakes up on mode transitions.
Change-Id: Ib224df434730f873ce5514303e5d043cbc85a9a4
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/30001
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Backlight control of internal panels likely won't work as configuration
for that seems absent in coreboot. Also, libgfxinit doesn't support any
MIPI/DSI connections, yet, and neither Gemini Lake.
TEST=Booted work-in-progress port kontron/mal10 with VGA text and
linear framebuffer modes. DP display came up.
Change-Id: I7b111f1cdac4d18f2fc3089f57aebf3ad1739e5d
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/29903
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Removes a warning in Linux about FACP.
Change-Id: Ia12302a4dcd34eacdcc8ae16bd39e951e616c6ea
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/30011
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
This change adds support to print ME version if UART_DEBUG is
enabled. Check for UART_DEBUG is necessary because talking to ME to
get the firmware version adds ~0.6 seconds to boot time.
TEST=Verified on octopus that ME version printed is correct.
Change-Id: I41217371558da1af694a2705e005429155d62838
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/29989
Reviewed-by: Justin TerAvest <teravest@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Replace IO access to ACPI registers with the new MMIO access functions.
BUG=b:118049037
TEST=Build and boot grunt. Test ACPI related functionality.
Change-Id: I7544169bb21982fcf7b1c07ab7c19c6f5e65ad56
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/c/29296
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
ACPI registers can be accessed through IO or through MMIO. However, the
offset relationship is not one to one. Therefore, definitions with the
correct offset for MMIO access are needed.
BUG=b:118049037
TEST=Use Chrome OS IOTOOLS io_readxx and mem_readxx to find the correct
relationship between ACPI IO and ACPI MMIO.
Change-Id: Id20754c0fc0af35bc9eb1a4b40c62fbf9ed6304d
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/c/29294
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
This makes the mainboard able to boot again.
Change-Id: Id96fbfd5c815431dba2f030fca62a5ea16b97393
Signed-off-by: Kevin Cody-Little <kcodyjr@gmail.com>
Reviewed-on: https://review.coreboot.org/c/29994
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
"if" is preferable over "#if", because it lets the compiler perform
syntax and type checks even if CONFIG_CONSOLE_SERIAL is disabled.
Change-Id: I45a763f2d854fbe9082795bc74de7a9d0fded3c9
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/c/29336
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Hug <philipp@hug.cx>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
clock_get_coreclk_khz() already detects whether the PLL or the input
clock (hfclk) is used.
Tested on HiFive Unleashed.
Change-Id: I264977b0de0b81ef74a014984b6d33638ab33f4b
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/c/29334
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Hug <philipp@hug.cx>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
The common finalise code is used by bd82x6x, Lynx Point, and Ibex Peak.
Lynx Point now benefits from being able to write-protect the flash chip.
For Lynx Point, writing the SPI OPMENU now happens in ramstage, as done
in bd82x6x.
Tested on an ASRock H81M-HDS (Lynx Point). When write-protection is
configured, flashrom reports all flash regions as read-only, and does
not manage to alter the contents of the flash chip.
Also tested on an ASUS P8H61-M LX (Cougar Point). Everything seems to
work as before.
Change-Id: I781082b1ed507b00815d1e85aec3e56ae5a4bef2
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/c/29977
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
The finalise handler is not called during S3 resume when using the
`BS_PAYLOAD_BOOT` approach. So, adopt the `lpc_final` approach used by
bd82x6x and others.
Tested on an ASRock H81M-HDS. The finalise handler is now called on
the normal boot path, and during S3 resume.
Change-Id: I9766a8dcbcb38420e937c810d252fef071851e92
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/c/29976
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
The ASRock H81M-HDS doesn't implement a finalise handler. To fix
this, and reduce code duplication in the process, make a common
implementation. There should be no functional change to boards with
existing finalise handlers, since the code is identical among them and
the new, common implementation.
Tested on an ASRock H81M-HDS. The finalise handler works.
Change-Id: I13b581a2219288019a4e0c9e618db3ac7c3c15ab
Signed-off-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-on: https://review.coreboot.org/c/29975
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
The WACOM 5C01 touch panel power-up delay of 10mS is too aggressive
and causes "failed to change power setting" errors in the kernel, so
this change increases the power-up delay to 20mS which allows enough
time for the WACOM device's i2c controller to wake up.
BUG=b:120090384
BRANCH=none
TEST=flash and boot nocturne, log into kernel, execute the following
command and make sure the string is not found :
dmesg | grep "failed to change power setting"
Change-Id: I1db0b3f5ce666b79d8ada2939ec865233ce52a56
Signed-off-by: Nick Vaccaro <nvaccaro@google.com>
Reviewed-on: https://review.coreboot.org/c/29988
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
We discovered that the gpios previously used for FPMCU_INT_L were in
two different groups with two different voltages (C group was at 3.3V
and D group was at 1.8V). Moving both to B group which is at 3.3V.
BUG=b:119447525
BRANCH=Nami
TEST=unlock OS with fingerprint
register fingerprint
run powerd_dbus_suspend and see if it goes int s0ix
Change-Id: I2332b0eb7a2f74e8178b95a23c8ac2091027a071
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/29872
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ren Kuo <ren.kuo@quanta.corp-partner.google.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Update USB port info according to the schematic file.
BUG=none
BRANCH=master
TEST=Compiles successfully and boot on DUT.
Change-Id: I7383b3d676fd7c775a6d749c70af65b28cf941eb
Signed-off-by: David Wu <David_Wu@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/29912
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Now that the relationship between IO access and MMIO access has been
established, create read/write functions to access ACPI standard registers
through MMIO.
BUG=b:118049037
TEST=Build grunt
Change-Id: I32c26f342885c0d99b082be98730edcf16ab5dfc
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/c/29295
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Handle situation when first NIC is not BDF 1:0.0. The PCI enumeration
is different when a external PCIe device is connected to mPCIe2 slot
which is routed to first PCIe bridge. The first NIC is then assigned
BDF 2:0.0, because it is connected to the second PCIe bridge.
Read the secondary bus number from the NIC PCIe bridge before attempting
to read MAC adress and calculating serial number.
Change-Id: I9f89a6f3cd0c23a2d2924e587338f69c260b12f8
Signed-off-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-on: https://review.coreboot.org/c/29842
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
This can be used to select the proper VBT.
Change-Id: Id3f6ba3ae31a5ab47f44d207678c1c4a6a43b7ec
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/29925
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Use of device_t is deprecated.
Change-Id: Ief858f6612d1c7b4b0c286cf5938f8c29055f1b5
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/29915
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Use of device_t is deprecated.
Change-Id: I2c88642133d3cbf33015e3e1e855fb2c786878d6
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/29914
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
All i82801gx targets now use SMM_TSEG.
Change-Id: Ib4e6974088a685290ed1dddf5228a99918744124
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/25599
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
This also caches the TSEG region and therefore increases MTRR usage a
little in some cases.
Change-Id: I5f947cfae730b67bc76a581bc90cb10e5a2a4a52
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/25598
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This also caches the TSEG region and therefore increases MTRR usage
a little in some cases.
Currently SMRR msr's are not set on model_1067x and model_6fx since
this needs the MSRR enable bit and lock set in IA32_FEATURE_CONTROL.
This will be handled properly in the subsequent parallel mp init
patchset.
Tested on Intel DG41WV, resume from S3 still works fine.
Change-Id: I317c5ca34bd38c3d42bf0d4e929b2a225a8a82dc
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/25597
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use the common SMM_TSEG code to relocate the smihandler to TSEG.
This also caches the TSEG region and therefore increases MTRR usage a
little in some cases.
This fixes S3 resume being broken introduced by CB:25594
"sb/intel/i82801gx: Use common Intel SMM code".
Currently SMRR msr's are not set on model_1067x and model_6fx since
this needs the MSRR enable bit and lock set in IA32_FEATURE_CONTROL.
This will be handled properly in the subsequent parallel mp init
patchset.
Tested on Intel d945gclf and Lenovo Thinkpad X60.
Change-Id: I0e6374746c3df96ce16f1c4a177af12747d6c1a9
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/25595
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use the common Intel code to set up smm and the smihandler.
This is expected to break S3 resume and other smihandler related
functionality as this code is meant to be used with CONFIG_SMM_TSEG.
The platform (x4x) using this southbridge will adapt
the CONFIG_SMM_TSEG codepath in subsequent patches.
Change-Id: Id3b3b3abbb3920d68d77fd7db996a1dc3c6b85a3
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/25596
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Sync the FSP settings with what coreboot does. Why both FSP and coreboot
configure this redundantly stays a secret.
TEST=Set SERIRQ_CONTINUOUS on kontron/mal10. A CPLD connected to LPC
works correctly now, but was confused by the wrong settings before
because the FSP defaults allowed to disable the LPC clock.
Change-Id: Id1c7180f460678bf0f9458228591050dd628c052
Signed-off-by: Nico Huber <nico.huber@secunet.com>
Reviewed-on: https://review.coreboot.org/c/29901
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Use acpigen_write_processor_cnot to implement notifications to the CPU.
Change-Id: I01e4397b9a1c15eff4b856cbc697fa2b4bc9761f
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/29893
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Use acpigen_write_processor_cnot to implement notifications to the CPU.
Change-Id: If482c64e7133cc6d82472d121ac138fc1b60a183
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/29892
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: David Guckian
Use acpigen_write_processor_cnot to implement notifications to the CPU.
Change-Id: Id64f9857bbd7db520c94de949db8f823f71d6dae
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/29891
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Use acpigen_write_processor_cnot to implement notifications to the CPU.
Automatically generate \PPKG in SSDT.
Change-Id: I79d2eed9b89b420554ce10d1fc0f151b1872afe2
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/29890
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Use acpigen_write_processor_cnot to implement notifications to the CPU.
Change-Id: I93c11e89da34c5432c6ce0415998b47bad339763
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/29889
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use acpigen_write_processor_cnot to implement notifications to the CPU.
Change-Id: Ifb5a5c1255f9a922063293bf430e849909468eaf
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/29888
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use acpigen_write_processor_cnot to implement notifications to the CPU.
Change-Id: I00d15d0640a37f89ffd5cc87b89d5ba11fecb9ed
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/29887
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: David Guckian
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use acpigen_write_processor_cnot to implement notifications to the CPU.
Automatically generate \PPKG in SSDT.
Change-Id: Iecc54e94484f5f11e0ba8ef6d1d844276e484b4d
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/29886
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use acpigen_write_processor_cnot to implement notifications to the CPU.
Change-Id: I182585fd09e4ce848c860d00eb612e8f5fdde35e
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/29884
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This sets up initial clock configuration for QUP and QSPI,
and includes configuration of Root Clock Generators(RCG) and
clock branches enablement.
TEST=build & run
Change-Id: I0b1d7f6daa179c0b24a97d42b66c1a9ee596b0a3
Signed-off-by: David Dai <daidavid1@codeaurora.org>
Reviewed-on: https://review.coreboot.org/c/25454
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
POWER8 is a specific implementation of ppc64, which is by now outdated
(POWER9 has been on the market for a while). Rename arch/power8/ to
potentially cover a wider range of hardware.
TEST=Toolchains built before/after this commit can build coreboot for
emulation/qemu-power8 from before/after this commit.
Change-Id: I2d6f08b12a9ffc8a652ddcd6f24ad85ecb33ca52
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-on: https://review.coreboot.org/c/29943
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Timothy Pearson <tpearson@raptorengineering.com>
Makes vboot measured boot mode available for all boards.
* Increase Tegra210 and Rockchip3228 SRAM for
romstage/verstage.
* Add missing files for Intel apollolake and
AMD stoneyridge as TPM driver target.
Change-Id: I35a85b8f137f28cd9960f2c5ce95f8fa31185b82
Signed-off-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/29840
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
The reason for this code cleanup is the legacy
Google Purin board which isn't available anymore
and AFAIK never made it into the stores.
* Remove broadcom cygnus SoC support
* Remove /util/broadcom tool
* Remove Google Purin mainboard
* Remove MAINTAINERS entries
Change-Id: I148dd7eb0192d396cb69bc26c4062f88a764771a
Signed-off-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/29905
Reviewed-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
According to aleena thermal testing to set STAPM values.
skin scalar for 80%.
time constant for 2500s.
power limit for 7.8w.
BUG=b:72979852
TEST=test build for thermal check.
Change-Id: I09f1c1052dd317969546ac7d2bbde14cc563c160
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/29795
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Correct Ram_ID=0b0001 SPD Module Part Number to "H5ANAG6NAMR-UH" from "HMAA51S6AMR6N-UH".
BUG=b:120000816
BRANCH=master
TEST=mosys memory spd print all
Change-Id: I59d920498ff6b73e9e7b2887771ad6bc6c6c0b66
Signed-off-by: Lucas Chen <lucas.chen@quanta.corp-partner.google.com>
Reviewed-on: https://review.coreboot.org/c/29873
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Martin Roth <martinroth@google.com>
Implement HD Audio verb table for RealTek ALC 3204/3254 codec on google
sarien and arcada board.
BUG=b:119058355,119054586
TEST=Confirm audio play back is working on Sarien and Arcada board.
Change-Id: Icedbb510c7668d96c99c657091fc865f03bf7783
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/29484
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Provide an reset macro that will use Verb ID 0x7ff and Payload 0 to
execute function reset.
Change-Id: Ie788b7153e25b764cd1d33753af17d5ed4903c36
Signed-off-by: Lijian Zhao <lijian.zhao@intel.com>
Reviewed-on: https://review.coreboot.org/c/29554
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Remove the __SIMPLE_DEVICE__ define from files used only in romstage.
This is not required since romstage always defines __SIMPLE_DEVICE__.
Change-Id: I8db1b15c9186536c9b8a6b5d667fa5a11af1bad2
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/29821
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This removes CEIL_DIV and div_round_up() altogether and
replace it by DIV_ROUND_UP defined in commonlib/helpers.h.
Change-Id: I9aabc3fbe7834834c92d6ba59ff0005986622a34
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/29847
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
On this mainboard there are legacy PCI device, which are connected to
different PCIe root ports via PCIe-2-PCI bridges. This patch disables
the unused PCI clock outputs on the XIO2001 PCI Express to PCI Bridges.
Change-Id: Id36e39c4568f5dd241cd864d2e75365abd0f2a91
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/29882
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
There is an on-board PCI device where bus master has to be enabled in
PCI configuration space. As there is no need for a complete PCI driver
for this device just set the bus master bit in mainboard_final().
Change-Id: I4ab40e34253c20adaacfdf42050314e06547eefb
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/29881
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
This mainboard also has a SD slot.
Change-Id: I969e8ecb27aee4c8be212e67dfe6bd807ecd3b2f
Signed-off-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-on: https://review.coreboot.org/c/29879
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
PMIC provides power features like auxadc, buck/ldo,
interrupt-controller..etc
BUG=b:80501386
BRANCH=none
TEST=Boots correctly on Kukui
Change-Id: Ic247faf73517f6512f9c9a69ba0254c749d68d4c
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/29422
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The PMIC wrapper is a proprietary hardware to connect the PMIC. This
patch implements PMIC wrapper driver for the communication with PMIC.
BUG=b:80501386
BRANCH=none
TEST=Boots correctly on Kukui
Change-Id: Idbdb15f11227ded3f5d18fe6504c8c646973b733
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Reviewed-on: https://review.coreboot.org/c/29421
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Julius Werner <jwerner@chromium.org>
The aleena board uses a display that's not compatible with current VBIOS.
A VBIOS specific for aleena has been merged into blobs, so modify Kconfig
so that it loads the new VBIOS when building aleena, but load original VBIOS
for all other boards under kahlee folder.
BUG=b:112618193
TEST=Build each board under kahlee, one at a time. After each build, opened
build/config.h and searched VGA_BIOS_FILE to verify that the string only
changed for aleena, all other boards remained with original string.
Change-Id: Iccd0853692680908d951edd142a2d8e13a561391
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/c/29870
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Marshall Dawson <marshalldawson3rd@gmail.com>
Reviewed-by: Martin Roth <martinroth@google.com>
When an untrusted OS is running, we would like to use the Cr50
vendor-specific VENDOR_CC_TPM_MODE command to disable TPM.
Before doing this, we should save TPM state. Implement
tlcl_save_state for this purpose.
This needs to live in coreboot codebase since on S3 resume path,
depthcharge is not reached.
Implement the function in both tcg-1.2 and tcg-2.0 for
completeness.
BUG=b:70681930,b:118202153
TEST=hack a call to tlcl_save_state into coreboot on S3 resume
verify in AP console that it is called
Signed-off-by: Joel Kitching <kitching@google.com>
Change-Id: I8b51ca68456fc9b655e4dc2d0958b7c040d50510
Reviewed-on: https://review.coreboot.org/c/29646
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Some "magic" numbers became public available registers/bits after the code
was originally written. Find all magic numbers, and if available in a public
BKDG than replace them with literals.
BUG=b:117648026
TEST=Build and boot grunt.
Change-Id: I96ac59fd92c4a5e27c3836f77bf6633e9b0c4990
Signed-off-by: Richard Spiegel <richard.spiegel@silverbackltd.com>
Reviewed-on: https://review.coreboot.org/c/29198
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Add support for updating microcodes on FSP 1.0 platforms
before memory is initialized. This is a requirement to
fill other FIT entries except for microcode updates.
Change-Id: Ie31acaf0fc41c51b9edf65b981d43d7732661770
Signed-off-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/29819
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Huang Jin <huang.jin@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Assign correct SATA port map.
Tested on HP8200:
All SATA ports are now usable in GNU/Linux.
Change-Id: I5be2b4f33882f6f71213f8173cdb945fc9b7af06
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-on: https://review.coreboot.org/c/29855
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Held <felix-coreboot@felixheld.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
The coming feature "measured boot" relies on VB2_LIB in romstage. In the
case where there is no separate verstage, compile the library just for
romstage as it will then be shared across verstage and romstage code. If
there is a separate verstage, compile the library separately for
verstage and romstage.
Change-Id: I8126c21b8fbe8dd65d95af49cbe2ad776b8ef605
Signed-off-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-on: https://review.coreboot.org/c/29827
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Philipp Deppenwiese <zaolin.daisuki@gmail.com>
RAM is reserved for Chromeos even when Chrome is not used.
Use CONFIG_CHROMEOS to determine is RAM must be reserved.
BUG=N/A
TEST=Intel BayTrail CRB
Change-Id: Ic1f5089227f802e2b2f62dc02fa0d1648c1855b5
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/29856
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Make pch_early_iorange_init() function similar to
soc/intel/cannonlake/bootblock/pch.c while fixing below issue:
* COM1 not being enabled properly.
TEST=Able to get serial output from an 8250IO UART device at
the standard 0x3f8 base address.
Change-Id: I5ab02f46d27e667be3d9328d94b634ef04038d2f
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/29835
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Using 0 for PIRQ_PIC_IRQDISABLE might conflict with using IRQ0 as PIRQ.
Change PIRQ_PIC_IRQDISABLE value to 0x80, so value 0 is reserved for IRQ0.
BUG=N/A
TEST=Intel CherryHill CRB
Change-Id: I18706f12e7c2293e948eb10818393f0d1870f514
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/29393
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The sizes of IO_BASE and ILB_BASE areas a incorrect.
Correct IO_BASE_SIZE and ILB_BASE_SIZE values.
BUG=N/A
TEST=Intel CherryHill CRB
Change-Id: I23c3fd608598c5ec2271d393168ac4bf406772b4
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/29392
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This is an issue found by the new builder image and needs to be fixed
before we can upgrade to the new toolchain version:
In function `bdk_dram_get_size_mbytes':
src/vendorcode/cavium/bdk/libbdk-dram/bdk-dram-size.c:198:
undefined reference to `bdk_pop'
In function `bdk_get_num_cores':
/src/vendorcode/cavium/include/bdk/libbdk-hal/bdk-utils.h:164:
undefined reference to `bdk_dpop'
In function `init_octeon3_ddr3_interface':
src/vendorcode/cavium/bdk/libdram/dram-init-ddr3.c:7550:
undefined reference to `bdk_pop'
Change-Id: Ibf71e4556014795bfedceccfe3837dc9deb29ad2
Signed-off-by: Martin Roth <martinroth@google.com>
Reviewed-on: https://review.coreboot.org/c/29851
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
The resources of the local APIC are not reserved.
Use mmio_resource() to add local APIC resources.
BUG=N/A
TEST=Intel CherryHill CRB
Change-Id: Ieb9de45098d507d59f1974eddb7a94cb18ef7903
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/29375
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
ACPI and GPIO base are used by LPC controller, but not reserved.
Both bases are added to the LPC device resources.
BUG=N/A
TEST=Intel CherryHill CRB
Change-Id: I5248694b497c4965d79dd7c25ec97592dc0dddbc
Signed-off-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-on: https://review.coreboot.org/c/29288
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
