Currently, we used to stitch extra VBT files to ADLRVP build using
Makefile. With enablement of emerge build, we should be able to
integrate more than 1 VBT binaries using ebuild.
This removing these lines to avoid compilation issues in emerge builds
BUG=None
BRANCH=None
TEST=Check if compilation passes on emerge build. Stitched additional
VBT files using emerge and checked that coreboot picks up correct VBT.
Change-Id: I69f1cc6c07415515ff85180fdd7cc5de11b4d805
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51765
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Meera Ravindranath <meera.ravindranath@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Add function to allow overriding the RcompResistor and
RcompTarget UPDs from mainboard if required.
Mainboard users can pass required rcomp from memory.c file.
Refactor ddr_config structure to take out rcomp related variable
outside for all memory type to override if required.
BUG=b:182772421
TEST=Able to override the default RcompResistor and RcompTarget
values.
Change-Id: Ie8528bbf0517728534d47f9adaabfc9a2c469609
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51683
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
List of changes:
1. Alder Lake MRC is expecting a RcompResistor value of word width.
Reference RCOMP resistors on motherboard are ~ 100 Ohms but coreboot
is passing an array of RcompResistor which is not completely in use.
Note: Rcomp resistor value represents rcomp resistor attached to
the DDR_COMP pins on the SoC.
2. Also, remove usage of '&' with memcpy the required value into
RcompTarget array.
3. Also, update RcompResistor value for ADLRVP.
BUG=b:183341229
TEST=Enable FSP debug log to verify the override value for
RcompResistor is reflecting correctly.
Change-Id: I69c7cec55b65036fc039c33374a3fd363ef7004e
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51704
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
With this change, only raminit.c uses pei_data.h definitions. With MRC
cornered, making it optional is just a matter of writing a replacement.
USB config definitions will be moved to Lynx Point code in a follow-up.
Tested on Asrock B85M Pro4, still boots and still resumes from S3.
Change-Id: I4bc405213e9b0828d9ced18677335533c7dd381d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51440
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This change enables CnviBtAudioOffload. FSP is invoked to configure
BT over USB and BT I2S pins for cAVS connection.
BUG=None
TEST=Verified BT offload working on ADL RVP
Signed-off-by: Usha P <usha.p@intel.corp-partner.google.com>
Change-Id: I1185a6c2295bae7d469be4da86502506adbeb8cb
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51032
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
It's common to use the raw, unshifted I2C address in coreboot. Adapt
mainboards accordingly and perform the shift in MRC glue code.
Tested on Asrock B85M Pro4, still boots and still resumes from S3.
Change-Id: I4e4978772744ea27f4c5a88def60a8ded66520e1
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51458
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Do not use the same name as the non-LP GPIO config. This allows checking
at build-time that a mainboard uses the correct GPIO config format.
Without this commit, there are no build-time errors when using the wrong
format of GPIO config, but there would be undefined behavior at runtime.
Tested by trying to build asrock/b85m_pro4 and hp/folio_9480m after
toggling the `INTEL_LYNXPOINT_LP` Kconfig option (and trimming down the
USB config arrays for asrock/b85m_pro4). In both cases, building failed
because the necessary GPIO config global is not defined, as expected.
Change-Id: Ib06507ef8179da22bdb27593daf972e788051f3a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51661
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Set chipset_lockdown in devicetree for recommended security settings.
Change-Id: Ie27450dd32463243b1456932a1d39d40afa81da1
Signed-off-by: Marc Jones <marcjones@sysproconsulting.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51388
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Jay Talbott <JayTalbott@sysproconsulting.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Mainboards do not need to know about `pei_data` to tell northbridge code
where to find the SPD data. Adjust `mb_get_spd_map` to take a pointer to
a struct instead of an array, and update all the mainboards accordingly.
Currently, the only board with memory-down in the tree is google/slippy.
Mainboard code now obtains the SPD index in `mb_get_spd_map` and adjusts
the channel population accordingly. Then, northbridge code reads the SPD
file and uses the index that was read in `mb_get_spd_map`, and copies it
to channel 0 slot 0 unconditionally. MRC only uses the first position of
the `spd_data` array, and ignores the other positions. In coreboot code,
`setup_sdram_meminfo` uses the data of each SPD index, so `copy_spd` has
to account for this.
Tested on Asrock B85M Pro4, still boots and still resumes from S3.
Change-Id: Ibaed5c6de9853db6abd08f53bbfda8800d207c3e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51448
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
In pursuit of the goal of eliminating the proliferation of raw region
devices to represent CBFS files outside of the CBFS core code, this
patch removes the get_spd_cbfs_rdev() API and instead replaces it with
spd_cbfs_map() which will find and map the SPD file in one go and return
a pointer to the relevant section. (This makes it impossible to unmap
the mapping again, which all but one of the users didn't bother to do
anyway since the API is only used on platforms with memory-mapped
flash. Presumably this will stay that way in the future so this is not
something worth worrying about.)
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Iec7571bec809f2f0712e7a97b4c853b8b40702d1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50350
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
This patch sets the HDMI audio mode to 8T as required by the latest FSP
version v2081_02
TEST: HDMI audio codecs detection is failing without this change.
Change-Id: Ie5a825da7d199c9ee61e64d8f4ee7dec28fdaacd
Signed-off-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51273
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
This patch disables the xDCI which is causing PC8 to PC10 state
transitions during sleep.
TEST: Confirmed that the transition is happening with this change.
Change-Id: I9bbf7b52c36954600d7e66f9b03fad39b8881a5f
Signed-off-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51282
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Enable the PCIe RTD3 driver for WWAN device attached to PCIe Root
Port 4 and provide the reset GPIO / src clk pin.
BUG=none
TEST=Boot to OS, verify the link is in L2 state during S0ix.
Change-Id: I669e02bd02e3af878648a6f3cf4fbb4d06c9857f
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51315
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Lance Zhao
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Remove the CNVi BT PCI config and add BT flag. There is no PCI host interface
in this version of CNVi.
TEST: BT is checked using 'lsusb -d 8087:0026' from OS to make sure BT is
enumerated.
Change-Id: I8de5615235f24e6169bf67dbbadb92e69437bc4e
Signed-off-by: Cliff Huang <cliff.huang@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50899
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Remove the CNVi Bt PCI config and add Bt flag.
There is no PCI host interface in this version of CNVi.
TEST: BT is checked using 'lsusb -d 8087:0026' from OS.
Change-Id: I17c3e2761f91fb397d140d1954b6d4b451c4c603
Signed-off-by: Cliff Huang <cliff.huang@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51351
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Add support to pick the right vbt from cbfs according to
SKU-ID.
Change-Id: I8795cc67d87429eddb31328f1e2a90c346b53533
Signed-off-by: Meera Ravindranath <meera.ravindranath@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48416
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
This change select the Kconfig to pre-allocate the Intel-recommended bus
and memory resources per-PCIe TBT root port for the adlrvp mainboard.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Ic56ebab02e50a466662a07d122d8f40eaf16b54b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51461
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Function is identical for all mainboards, so factor it out.
Change-Id: Ibe08fa7ae19bfc238d09158309f0a9fdb31ad21c
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50028
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: I55815a824ea3a77e6e603ba4beb17457f37c48f5
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49433
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This patch adds the changes to enable the TCSS.
BUG=b:175808146
TEST= Boot shadowmountain board, Test the functionality of the Type-C
ports on both the mainboard and daughterboard by plugging in the Type-C
devices and verified the devices are detected via EC console and in the
OS.
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Change-Id: Ieaf1170ca718a14d24b773a4a85516e0bbfbb569
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51026
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
PCIEXP_HOTPLUG has a prompt and as such is not supposed to be forced.
Just change the default value to 'y'.
Change-Id: Ie4248700f5ab5168bff551b740d347713273763c
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51151
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This is a cosmetic change.
Make the formatting consistent with the rest of the tree.
Change-Id: Ic90e5584938592f1c2ab41edfcc773702822070d
Signed-off-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51149
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This is to align with newer platforms.
Change-Id: If33ea3a7835ec071be3fd060f9712c47678bd6bf
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50963
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This reverts commit d510b60f5b.
This patch includes the DSDT ASL code for shadowmountain board.
BUG=b:175808146
TEST= Boot shadowmountain board, dump and verify the DSDT ASL entries.
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Change-Id: I5aa60730fc9b93fa97b2bafbb8b2714b6b37becc
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50993
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This patch includes the ramstage changes for the
shadowmountain board.
BUG=b:175808146
TEST= Build and boot shadowmountain board.
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Change-Id: I419eecefddf9ee6e4249ada041ebeb1b78e85eb7
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49732
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
List of changes:
1. Add mainboard Kconfig to Kconfig.name files
2. Handle mainboard names in Kconfig file for adlrvp
3. Created a new devicetree.cb for Adlrvp-m.
3. Add override devicetree for ADL-M RVP.
4. Configure proper PCI and USB ports as per schematics for ADL-M
BUG=None
BRANCH=None
TEST=Able to build ADL-M RVP variants adlrvp_m and adlrvp_m_ext_ec.
Signed-0ff-by: Maulik Vaghela <maulik.v.vaghela@intel.com>
Signed-off-by: Varshit Pandya <varshit.b.pandya@intel.com>
Change-Id: I997b89ba87fb03dfa6a836caec51efd05baa2e8d
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49871
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch includes the romstage changes for the
shadowmountain board.
BUG=b:175808146
TEST= Build and boot shadowmountain board till early ramstage.
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Change-Id: Ifd0bbcea9d4916d82bb1e3c275dd79d97a79727a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49731
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Some (notably older Intel) boards use a tabular description of irq
routing that we want to keep pristine no matter what clang-format
considers correct (as that's ugly).
Change-Id: I259255a9f60208c659b658ecb81535e84a2aaa8c
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50545
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Move `CROS_GPIO_DEVICE_NAME` to a new `chromeos.h` header, because
Lynxpoint uses a different value. Also drop unnecessary includes.
Tested with BUILD_TIMELESS=1, Google Tidus remains identical.
Change-Id: I38baed2c114fb93cfb82535a6ec00fb67e596d64
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50080
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Use global variables to provide mainboard USB settings, and have the
northbridge code copy it into the `pei_data` struct. For now.
To minimize diffstat noise, this patch does not reindent the now-global
mainboard USB configuration arrays. This is cleaned up in a follow-up.
Change-Id: I273c7a6cd46734ae25b95fc11b5e188d63cac32e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50538
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Desktop boards do not have any backlight control.
Change-Id: Ie9f5f4d7e6ae09b3d664d53e4c03157fd4ed088e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50501
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Platform code will overwrite these values anyway, so do not program them
in mainboards.
Change-Id: I7571d336a1402c6cfae5835a95dc706a28106271
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49751
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Was copy-pasted from i82801ix and no mainboard actually needs it.
Change-Id: I400424540b52dc5d43aba15720b18ad57ea2ebda
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49279
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Variable PICM was not inside GNVS region and can use a static
initialisation value.
For most AMD platforms PICM default changes from 1 to 0.
Fix comments about PICM==0 used to indicate use of i8259 PIC for
interrupt delivery.
Change-Id: I525ef8353514ec32941c4d0c37cab38aa320cb20
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49905
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The value should be set by OSPM using some combination of
_OSI() queris in the \_SB._INI() method.
To maintain previous behaviour with this commit, boards where
GNVS osys initialisation was removed now do the same in ASL.
Change-Id: Id4957b12a72fbf7fa988e7ff039e47abcc072e1c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49353
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Initialize variable to 1 to indicate AC power supply.
If platform has EC it will set this correctly based on
whether plugged on the charger or not.
Change-Id: I3f834cf7563b9e512fcab34cdb7a27a9f0fd31c0
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49352
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This reverts commit 2151f7561d.
Reason for revert: It depends on the shadowmountain ramstage patch.
Error on the builder:
IASL /cb-build/coreboot.0/default/INTEL_SHADOWMOUNTAIN/dsdt.aml
src/mainboard/intel/shadowmountain/dsdt.asl:4:10: fatal error: baseboard/ec.h: No such file or directory
#include <baseboard/ec.h>
^~~~~~~~~~~~~~~~
compilation terminated.
Change-Id: I9fa5e8cc2ad485bf82bfbda151bc46d26faef7ab
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50055
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This patch includes the DSDT ASL code for shadowmountain board.
BUG=b:175808146
TEST= Boot shadowmountain board, dump and verify the DSDT ASL entries.
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Change-Id: I511b2d23c424b0565ad1abcc3b41cace1b89936e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49733
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch includes the bootblock and verstage changes for
shadowmountain board.
BUG=b:175808146
TEST= Build and boot shadowmountain board till early romstage.
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Change-Id: I5f805baf42203306ff10e91a258d9117dd986c4a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49479
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Refactor PCIE port config structure. Make it easier to map from
schematic. We don't have to convert the PCIE ports RP number and
CLK source in devicetree. All the convert will be done by SoC level.
Signed-off-by: Eric Lai <ericr_lai@compal.corp-partner.google.com>
Change-Id: I0b390e43f8e99b19cfad178139b86a2f77d7a57b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48340
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Even the boards with MAINBOARD_HAS_CHROMEOS need to be build-tested
with CHROMEOS=n.
Change-Id: I16fcf62a23dae1b21c77cee275c867f9c1de893b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50118
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
As per Hardware Architecture Specification (HAS) ADL-P has 7 CLKSRC
and 10 CLKREQ (7 SRCCLK is internal and 3 SRCCLK from external CLK chip).
ADL-M has 6 SRCCLK and CLKREQ (no external CLK chip).
Change-Id: I7d223c165f819669722cbc80245fa8ec20372352
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/50130
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Objects that are created with acpigen need to be declared
with External () for the generation of dsdt.asl to pass
iasl without errors.
There are some objects that are common to all platforms,
and some that should be declared only conditionally.
Having a top-level ASL helps to achieve this.
Change-Id: Ibaf1ab9941b82f99e5fa857c0c7e4b6192c74330
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49794
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Christian Walter <christian.walter@9elements.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Remove typedef device_nvs_t and move struct device_nvs
outside of global_nvs. Also remove padding and the reserve
for chromeos_acpi_t.
Change-Id: I878746b1f0f9152a27dc58e373d58115e2dff22c
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49476
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This change uses the newly added meminit block driver and updates TGL
SoC and mainboard code accordingly.
TEST=Verified that UPDs are configured correctly with and without this
change.
Change-Id: I6d58cd6568b7bbe03c4e3011b2301209893e85a9
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49042
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
All Broadwell boards only use the `mainboard_pre_raminit` function to
call `mainboard_fill_pei_data` and optionally `mainboard_fill_spd_data`.
Move the declaration and weak definition of `mainboard_fill_spd_data` to
platform code, replace the call to `mainboard_pre_raminit` in romstage.c
with calls to `mainboard_fill_pei_data` and `mainboard_fill_spd_data`,
and delete all other instances of `mainboard_pre_raminit` for Broadwell.
Finally, delete now-empty romstage.c and spd.h files from mainboards.
Change-Id: I3334b20bd7138bb753b996a137ff106e87c6e8a5
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49776
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Make it optional and change its signature.
Change-Id: I4b5f3fb08e8954514ebf39e72c95aa62d66856d7
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49775
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
This allows us to drop many now-redundant Kconfig options.
Tested with BUILD_TIMELESS=1, Purism Librem 13 v1 remains identical.
The default configuration file also remains identical, as expected.
Change-Id: I20b0200550508679bf2533342ce918b221dcf81e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46953
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: Ib827e9b2919dbd0e16f30b8dfde46348365d9622
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49438
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early gpio table for the board as a
first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: I8b30eb5d70c34ae3e2ed24ab52dd1357a54c5ae7
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49439
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: I0b956427a9cec56d06b03f7f05138f75137b4ea3
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49437
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: Ibc727302109456eb1d86652c947ce85b3a64c5b2
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49436
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: I80369ab70d5510cb4f388f3029119e7148361af4
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49435
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to a early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: Id6b55d7f3d3fbfc5b55497708f24006614760d03
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49434
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: I130fd26944169430a84c3609432b1b5283581c99
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49432
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: Ie3878b47b8e20c51b928a38df9ccedf2d50d478e
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49431
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.
Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).
Change-Id: Ib19a4f64eaf25bf2eb47ee60748a68538fc0729a
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49430
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The LPC/eSPI pad configuration is already done at board-level. Thus,
drop redundant configuration by dropping the call to lpc_configure_pads.
Change-Id: Ib9e62bf19e6f1fbe32a340e4802c13504a0d6def
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49417
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Do LPC/eSPI pad configuration at board-level to match other platforms by
adding an appropriate early gpio table in the bootblock.
The soc code gets dropped in CB:49410.
Change-Id: Ie1e53e72c65fdcfe4be2e01134873aa7858c28ff
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49416
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Do LPC/eSPI pad configuration at board-level to match other platforms.
This is done by adding one missing pad to the early gpio table and
dropping the call to the soc function.
The soc code gets dropped in CB:49410.
Change-Id: I210633d4520fcfab59f68268bd7991557433ce38
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49415
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Functionality depends of CMAP and CMBP references inside board
specific ASL implementation. Only roda/rk9 and roda/rk886ex has
that.
Change-Id: I4da8292375cb589d67dc68496b1e81971bc2a61f
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49274
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
APIC was not referenced anywhere in ASL.
MPEN has references under boards:
getac/p470, roda/rk9, roda/rk886ex.
MPEN has reference also in Intel SpeedStep ASL.
Replace static MPEN with detection of multiple CPUs
installed.
Change-Id: Ib5f06416b23196b7227ccd5814162925c31c084b
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49273
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Chrome EC dropped strago support, so we need to disable it here
before updating our Chrome EC submodule.
Change-Id: Ied8905e995fd040b981ce18e95e225ade496d23c
Signed-off-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48216
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Having some symmetry with <soc/nvs.h> now allows to reduce
the amount of gluelogic to determine the size and cbmc field
of struct global_nvs.
Since GNVS creation is now controlled by ACPI_SOC_NVS,
drivers/amd/agesa/nvs.c becomes obsolete and soc/amd/cezanne
cannot have this selected until <soc/nvs.h> exists.
Change-Id: Ia9ec853ff7f5e7908f7e8fc179ac27d0da08e19d
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49344
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Lance Zhao
There's no need to have them in the devicetree. ACPI generation can now
be simplified even further, and is done in subsequent commits.
Change-Id: I3a788423aee9be279797a1f7c60ab892a0af37e7
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46908
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Basking Ridge is not ULT, thus does not support C-states deeper than C7.
Replace them with the values used by all other Haswell non-ULT boards to
allow subsequent commits to cleanly factor them out of the devicetree.
Change-Id: Ife34f7828f9ef19c8fccb3ac7b60146960112a81
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46907
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Drop the support for the Intel Cannon Lake SoC for various reasons:
* Most people can't use coreboot on Cannon Lake, since the required FSP
binaries aren't publicly available. Given that FSP binaries for several
newer platforms have been released, it's very unlikely that Cannon Lake
FSP will ever be released.
* It seems there is no interest in this, since the reference mainboard
is the only available mainboard in tree.
Also, remove the related reference mainboard intel/cannonlake_rvp and
its FSP headers in intel/fsp2_0/cannonlake.
Change-Id: I8f698e16099acb45444b2bc675642d161ff8c237
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48775
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
List of changes:
1. Create new Kconfig MAX_CPU_ROOT_PORTS and MAX_PCH_ROOT_PORTS as per
EDS.
2. Add new chip variable to enable/disable CPU PCIE RPs from mainboards.
3. Rename PcieRpEnable to PchPcieRpEnable.
4. Enable CPU RPs as below in mainboard devicetree.cb
RP1: PEG60 : 0:6:0 : CPU SSD1
RP2: PEG10 : 0:1:0 : x8 CPU Slot
RP3: PEG62 : 0:6:2 : CPU SSD2
Change-Id: I92123450bd7cfb2e70aae8de03053672a7772451
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49136
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
These boards without ChromeEC do not set ACTIVE_EC_RW
flag as part of the gnvs_assign_chromeos() function.
Create abstraction to avoid <vendorcode/chromeos/x> include.
Change-Id: Ic6029e1807fcfe7dd2c766ce8221e347b6b096f9
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48777
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Make EC_GOOGLE_CHROMEEC_SWITCHES depend on VBOOT, rather than force
selecting it.
Change-Id: If96b2a935d2f7388a24be7d8e65c7dfc2c89a0fc
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49103
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Make GBB_FLAG_DISABLE_EC_SOFTWARE_SYNC depend on VBOOT,
rather than force-select it.
Change-Id: I0ec418d4182865636b6350f1ee151420d8e02c33
Signed-off-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49102
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
All Broadwell boards use 8 for MAX_CPUS, so this option can be factored
out into SoC Kconfig.
Change-Id: I311b95ea75a7c6b76b32c7197a0cec86db644234
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49122
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Configure MAX_CPUS in SoC Kconfig with 8 as default value and remove it
from every mainboard where 8 is used.
Change-Id: I825625bf842e8cd22dada9a508a7176e5cc2ea57
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49105
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Matt DeVillier <matt.devillier@gmail.com>
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Haswell and Broadwell have at most 8 threads.
Change-Id: Idcccf22addb6e15d7c55b9816141af47d6186cca
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46952
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
They aren't specific to AC power operation anymore. Also adapt autoport.
Change-Id: Ib04d0a08674b7d2773d440d39bd6dfbd4359e0fb
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49089
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
All mainboards use the same values for AC and battery, even desktop
boards without a battery. Use the AC values everywhere and drop the
battery values. Subsequent commits will rename the AC power options
accordingly, and will also clean up the corresponding acpigen code.
This is intentional so as to ease reviewing the devicetree changes.
Also update util/autoport accordingly.
Change-Id: I581dc9b733d1f3006a4dc81d8a2fec255d2a0a0f
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49088
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
One of the variants lacks an hda_verb.h, and hda_verb.c can't be built.
Follow-up changes will make mainboard hda_verb.c files always get built
through AZALIA_PLUGIN_SUPPORT, and breaks building this contraption.
Turn the headers into standalone compilation units to prevent this
issue. Since they contain definitions, including them from multiple
compilation units wasn't a good idea anyway.
Change-Id: I00d968563539a4e1b8d1e12145293439d8358555
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48360
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change enables PCIEXP_HOTPLUG to support resource allocation for
TCSS TBT/USB4 ports.
Referred from TGLRVP -> https://review.coreboot.org/c/coreboot/+/41543
Change-Id: I5f883dac0d7e5fa84ad2e1683f84c933a90cea51
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48619
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Remove unreferenced settings and factor out common settings. Many of
these are not mainboard-specific, and all boards use the same value.
Change-Id: Iecae61994a068e8022638a2ad9ca10174427f0a4
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48577
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Michał Żygowski <michal.zygowski@3mdeb.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Unset devicetree settings default to zero, so the devicetree setting can
be removed. Looks like no one needs it anyway.
Change-Id: Iad94538c5465347b37a99c6c9f20988168661593
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48575
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-by: Furquan Shaikh <furquan@google.com>
1. Make CLKSRC -> 7 and CLKREQ -> 6
2. CLK 6 is using free running CLK
3. Make LAN CLK 7 as unused as GbE is disable
TEST=Able to detect PCIE SD card on 0x1 slot.
Change-Id: I7fbde9492a0c59fc76931bfb7c9522d4f208ebb0
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48449
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Update memory parameters based on memory type supported by
Elkhart Lake CRB:
1. Update spd data for EHL LPDDR4X memory
- DQ byte map
- DQS CPU-DRAM map
- Rcomp resistor
- Rcomp target
2. Add configurations for vref_ca & interleaved memory
3. Add EHL CRB on board LPDDR4X SPD data bin file
4. Update mainboard related FSPM UPDs as part of memory
initialization
Signed-off-by: Tan, Lean Sheng <lean.sheng.tan@intel.com>
Change-Id: Ifd85caa9ac1c9baf443734eb17ad5683ee92ca3b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48127
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Remove JSL specific SMBIOS sku id info as it is not required by
EHL.
Signed-off-by: Tan, Lean Sheng <lean.sheng.tan@intel.com>
Change-Id: Ib672eb456ba62f2eb7f941630c4fbb34823664f5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48123
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
THis patch removes IPU & MIPI related support from EHL CRB as they
are not supported in EHL.
Signed-off-by: Tan, Lean Sheng <lean.sheng.tan@intel.com>
Change-Id: I3eb038009daaabd048f40c7953cb2c111cd4fe63
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48122
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Since there is no EC support on EHL CRB, this patch removes board
ID detection via EC (board_id.c & board_id.h) and its related
files. Temporarily removes variant_memcfg_config function in
romstage_fsp_param.c, will be added back when updating memory
configs later.
Signed-off-by: Tan, Lean Sheng <lean.sheng.tan@intel.com>
Change-Id: I40d96285dc05ec5faabc123950b6b3728299e99a
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48121
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Since EHL CRB does not support ChromeOS, this patch removes
ChromeOS EC related headers (ec.h & gpio.h) and #includes.
Signed-off-by: Tan, Lean Sheng <lean.sheng.tan@intel.com>
Change-Id: I9c0c3722065c041769081f3d564646ce6a565a9b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48119
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Since there is no ChromeOS support for EHL CRB, drop smihandler.c
which just deals with ChromeOS support.
Signed-off-by: Tan, Lean Sheng <lean.sheng.tan@intel.com>
Change-Id: Id474c3b04a82c03dda6514cc4565b58fb790b9c1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48118
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Since ChromeOS is not officially supported for EHL CRB, removing
ChromeOS related codes. Here are the change details:
- Remove ChromeOS related kconfig switches, including
SOC_INTEL_CSE_LITE_SKU which has dependency on ChromeOS flag
- Remove chromeos.c file
- Remove ChromeOS dsdt related codes from dsdt.asl & mainboard.c
- Remove ChromeOS GPIO related codes from variants.h & gpio.c
Signed-off-by: Tan, Lean Sheng <lean.sheng.tan@intel.com>
Change-Id: I4aabd40a4b46d4e64534b99e84e0523eaeaff816
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48117
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
This is a initial mainboard code cloned entirely from jasperlake_rvp
aimed to serve as base for further mainboard check-ins.
This patch is based on TGL_upstream series patches:
https://review.coreboot.org/c/coreboot/+/37868
List of changes on top off initial jasperlake_rvp clone:
1. Replace "Jasperlake" with "Elkhartlake"
2. Replace "jsl" with "ehl"
3. Replace "jslrvp" with "ehlcrb"
4. Remove unwanted SPD file, add empty SPD as placeholder
6. Empty romstage_fsp_params.c, to fill it later with SOC specific
config
7. Empty GPIO configurations, to be filled as per board
8. Empty memory.c configurations, to be filled as per board
9. Add board support namely BOARD_INTEL_ELKHARTLAKE_CRB
10. Replace jslrvp variant with ehlcrb variant
Changes to follow on top of this:
1. Add correct memory parameters, add SPDs
2. Clean up devicetree as per tigerlake SOC
3. Add GPIO support
4. Update ehl fmd file to replace 32MB chromeos.fmd
Signed-off-by: Tan, Lean Sheng <lean.sheng.tan@intel.com>
Change-Id: I2cbe9f12468318680b148739edec5222582e42a0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47707
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Werner Zeh <werner.zeh@siemens.com>
This patch adds the PMC MUX and CONx devices for adlrvp for
conn2.
BUG=b:170607415
TEST=Built and booted adlrvp. Verified the PMC.MUX CONx objects
in SSDT tables.
Change-Id: I52afbd429750cfa416f4ed93aeb1be590f8c3a5c
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48230
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change restricts SI_ME region to live below the 16MiB boundary to
ensure that no regions cross the 16MiB boundary as the extended BIOS
window checker for FMAP complains about it.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Ib0838ff4c63b06b8dc169b40d3022965b2f2f8f9
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48189
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Remove SOC_INTEL_COMMON_BLOCK_HDA from mainboards Kconfig since it is
selected by their SoC soc/intel/cannonlake.
Change-Id: I9597746a217575b42f6325998b948e16b452231a
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48289
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch renames cbfs_boot_map_with_leak() and cbfs_boot_load_file()
to cbfs_map() and cbfs_load() respectively. This is supposed to be the
start of a new, better organized CBFS API where the most common
operations have the most simple and straight-forward names. Less
commonly used variants of these operations (e.g. cbfs_ro_load() or
cbfs_region_load()) can be introduced later. It seems unnecessary to
keep carrying around "boot" in the names of most CBFS APIs if the vast
majority of accesses go to the boot CBFS (instead, more unusual
operations should have longer names that describe how they diverge from
the common ones).
cbfs_map() is paired with a new cbfs_unmap() to allow callers to cleanly
reap mappings when desired. A few new cbfs_unmap() calls are added to
generic code where it makes sense, but it seems unnecessary to introduce
this everywhere in platform or architecture specific code where the boot
medium is known to be memory-mapped anyway. In fact, even for
non-memory-mapped platforms, sometimes leaking a mapping to the CBFS
cache is a much cleaner solution than jumping through hoops to provide
some other storage for some long-lived file object, and it shouldn't be
outright forbidden when it makes sense.
Additionally, remove the type arguments from these function signatures.
The goal is to eventually remove type arguments for lookup from the
whole CBFS API. Filenames already uniquely identify CBFS files. The type
field is just informational, and there should be APIs to allow callers
to check it when desired, but it's not clear what we gain from forcing
this as a parameter into every single CBFS access when the vast majority
of the time it provides no additional value and is just clutter.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Change-Id: Ib24325400815a9c3d25f66c61829a24a239bb88e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/39304
Reviewed-by: Hung-Te Lin <hungte@chromium.org>
Reviewed-by: Wim Vervoorn <wvervoorn@eltan.com>
Reviewed-by: Mariusz Szafrański <mariuszx.szafranski@intel.com>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Current flash layout doesn't support the fsp debug builds since
the FW_MAIN_A/B doesn't have enough space to hold the fsp debug
binaries along with ME RW binaries.
This patch reduces the SI_ALL size to 3.5MiB and increase the
SI_BIOS to 12.5MiB to include both ME RW and FSP debug binaries.
BRANCH=dedede
TEST=Build and Boot jslrvp with fsp debug enabled coreboot.
Cq-Depend: chrome-internal:3425366
Change-Id: I6f6354b0c80791f626c09dabafe33eefccedb9c2
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48154
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
As per latest schematics GPP_A15 is not used for EC_SYNC_IRQ
hence remove the unused GPIO.
Wrong GPIO configuration is causing platform reboot issue on
ADLRVP with Chrome SKU.
Change-Id: I704cd722683258c80197d8872d3bdaafb7c923dc
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48131
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
1. Add 2 ports and 2 endpoints
2. Add support for OVTI5675
WFC Cam is on I2C5 and UFC is on I2C1
BUG=None
BRANCH=None
TEST=Build and Boot adlrvp board and able to capture image
using camera.
Signed-off-by: Varshit Pandya <varshit.b.pandya@intel.com>
Change-Id: I6d2a4fdca99354d1b6977233c70ccd950c99d8a2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47497
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Configure I2C related GPIO as per ADL-P schematics.
This is based on Revision 0.974 of schematics.
Signed-off-by: Varshit Pandya <varshit.b.pandya@intel.com>
Change-Id: I76e1207cb31bed10b6e9fbeb2456b6feec42f97e
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47495
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
List of changes in SPD:
1. SPD Revision (of JEDEC spec)
2. SDRAM Maximum Cycle Time (tCKAVGmax) (MTB)
3. MSB -> CAS Latencies Supported, First Byte
4. CAS Latencies Supported, Second Byte
5. CAS Latencies Supported, Third Byte
6. LSB -> CAS Latencies Supported, Fourth Byte
7. Minimum CAS Latency Time (tAAmin)
8. Fine Offset for SDRAM Maximum Cycle Time (tCKAVGmax)
9. Fine Offset for SDRAM Minimum Cycle Time (tCKAVGmin)
10.Cyclical Redundancy Code (0- 125 byte)
TEST=Able to build and boot with updated SPD.
Change-Id: Iae7f2693e87bffb2dfa20bd07b22f4a4768c56cb
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48079
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
List of changes:
1. Initialize dq_map array in a single line
2. Make dqs_map array also in a single line
TEST=Able to build and boot ADLRVP LP4 SKU.
Change-Id: I64f2b38492934c8ede301f4b252c8700060ed4ac
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/48077
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Only Sandy Bridge MRC stores scrambler seeds in CMOS. Non-Sandybridge
boards ended up with these entries because of copy-paste programming.
Change-Id: I5a5bda6ea4e63ba03a4219bb2a6aa546bb6ecd7a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47149
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Time has shown that using spaces never converges into proper alignment.
Change-Id: I5338aeaf139580f9eab3e1e02cb910080a95d2c2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47147
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Most of these comments have been copy-pasted or serve no purpose other
than to eventually turn into misleading info. While the description of
the first 120 bits of CMOS could be useful, it should instead be added
to the documentation for the CMOS option infrastructure, or /dev/null.
Moreover, trim down newlines to no more than two consecutive newlines.
Change-Id: I119b248821221e68c4e31edba71ba83b7d2e14e9
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47143
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
List of changes:
1. Configure CTRLCLK and CTRLDATA for HDMI
2. Enable Ddc and HPD for Port-B
3. Disable dual eDP configuration for Port-A and B
TEST=Able to see depthcharge pre-boot screens over HDMI-B port.
Change-Id: I7509b981f35fc60a7885b2b07067cb0d35ec625f
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47838
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This patch modifies flash layout to add ME_RW_A/B to add
the CSE RW blob and also enable the CSE RW update feature for
JSLRVP
BUG=b:169077783
TEST= Built for jslrvp. Verified that CSE RW and metadata files
are included in cbfs.
Change-Id: I13baa317a06d00cec0337f08754892c7c8737f5d
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47557
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Currently the decision of whether or not to use mrc_cache in recovery
mode is made within the individual platforms' drivers (ie: fsp2.0,
fsp1.1, etc.). As this is not platform specific, but uses common
vboot infrastructure, the code can be unified and moved into
mrc_cache. The conditions are as follows:
1. If HAS_RECOVERY_MRC_CACHE, use mrc_cache data (unless retrain
switch is true)
2. If !HAS_RECOVERY_MRC_CACHE && VBOOT_STARTS_IN_BOOTBLOCK, this
means that memory training will occur after verified boot,
meaning that mrc_cache will be filled with data from executing
RW code. So in this case, we never want to use the training
data in the mrc_cache for recovery mode.
3. If !HAS_RECOVERY_MRC_CACHE && VBOOT_STARTS_IN_ROMSTAGE, this
means that memory training happens before verfied boot, meaning
that the mrc_cache data is generated by RO code, so it is safe
to use for a recovery boot.
4. Any platform that does not use vboot should be unaffected.
Additionally, we have removed the
MRC_CLEAR_NORMAL_CACHE_ON_RECOVERY_RETRAIN config because the
mrc_cache driver takes care of invalidating the mrc_cache data for
normal mode. If the platform:
1. !HAS_RECOVERY_MRC_CACHE, always invalidate mrc_cache data
2. HAS_RECOVERY_MRC_CACHE, only invalidate if retrain switch is set
BUG=b:150502246
BRANCH=None
TEST=1. run dut-control power_state:rec_force_mrc twice on lazor
ensure that memory retraining happens both times
run dut-control power_state:rec twice on lazor
ensure that memory retraining happens only first time
2. remove HAS_RECOVERY_MRC_CACHE from lazor Kconfig
boot twice to ensure caching of memory training occurred
on each boot.
Change-Id: I3875a7b4a4ba3c1aa8a3c1507b3993036a7155fc
Signed-off-by: Shelley Chen <shchen@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46855
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Select `PM_ACPI_TIMER_OPTIONAL` to enable the new PM ACPI Kconfig and
set the FSP option for PM ACPI timer enablement from its value instead
of using the old devicetree option.
Also drop the obsolete devicetree option from soc code and from the
mainboards and add a corresponding Kconfig entry instead.
Change-Id: I10724ccf1647594404cec15c2349ab05b6c9714f
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45955
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Instead of relying on mainboards to call it, do like Lynx Point.
Change-Id: Idb7457e0734e19d0a26f0762079e273b6e740475
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46793
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
It is identical for all Broadwell mainboards, thus deduplicate it.
Change-Id: I74559fbe42e44aa4d15ced5d88f6c15a1bf5203b
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46792
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Rename it to `hostbridge.asl`, which is what Haswell uses.
Change-Id: I6f97fc5c9459fe6b66dcfcf51900c751beda0ebe
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46786
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The other two modes are not used by any mainboard, and the code seems to
be copied from older southbridges. As the code looks incorrect, drop it.
Change-Id: I374546279a85cead1aea13e0952bbfd6f643a75b
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47022
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
This patch adds the PMC MUX and CONx devices for adlrvp. Device
specific method contains the port and orientation details used
to configure the mux.
BUG=b:170607415
TEST=Built and booted adlrvp. Verified the PMC.MUX CONx objects
in SSDT tables.
Change-Id: I3b5bb73991feb99577c16fea00c381dd0f855769
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47289
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Update Power Limit2 (PL2) minimum value to the same as maximum value for
jasperlake rvp board. DTT does not throttle PL2, so this minimum value
change here does not impact any existing behavior on the system.
BUG=None
BRANCH=None
TEST=Build and test on jasperlake rvp board
Change-Id: I862f7106846de5fb37f74419807eedc3096ded8a
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47201
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Furquan Shaikh <furquan@google.com>
List of changes:
1. Use devicetree.cb from default location
2. Create variant directory for ADL RVP with external EC as
'adlrvp_p_ext_ec'
3. Add initial overridetree.cb for 'adlrvp_p' and 'adlrvp_p_ext_ec'
to override 'devicetree.cb' as applicable.
4. Move all common files between 'adlrvp_p' and 'adlrvp_p_ext_ec'
to mainboard directory
TEST=Build and boot both ADLRVP with onboard and external EC.
Change-Id: I3591e214ed32dc9baaa49b92dff59579f29c7bd6
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/47335
Reviewed-by: V Sowmya <v.sowmya@intel.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change reorganizes the CNVi device entries in mainboard
devicetree/overridetree and SoC chipset tree to make it consistent
with how other SoC internal PCI devices are represented i.e. without a
chip driver around the SoC controller itself.
Before:
chip drivers/wifi/generic
register "wake" = "..."
device pci xx.y on end
end
After:
device pci xx.y on
chip drivers/wifi/generic
register "wake" = "..."
device generic 0 on end
end
end
Change-Id: I22660047a3afd5994400341de0ca461bbc0634e2
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46865
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Now that soc_get_pmc_mux_device() is gone, the PMC MUX connector devices
can be hooked up together via devicetree aliases.
Signed-off-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Change-Id: Ib51764da5b3c029f9ac7ac60199a0aedfc7f29b1
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45878
Reviewed-by: Furquan Shaikh <furquan@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Flesh out the PCH configuration into a separate chip. Keep it within the
Broadwell SoC directory for now, to ease moving files around. The boards
were prepared beforehand and the devicetrees require next to no changes.
Tested on out-of-tree Acer Aspire E5-573, still boots.
Change-Id: I28d948f3e6d85e669d12b29516d867c1d1ae9e1a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46700
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
List of changes:
1. Split mem_cfg for DDR4 and LPDDR4 as per board_id
2. Move dq_pins_interleaved into board-specific memory configuration
information
TEST=Able to build and boot DDR4 and LPDDR4 ADLRVP SKUs.
Change-Id: I6ef19209767c810426bba0c8bc48178bf2e2a110
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46873
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The dt option `speed_shift_enable` is obsolete now. Drop it.
Change-Id: I5ac3b8efe37aedd442962234478fcdce675bf105
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46462
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Get rid of legacy pad macros by replacing them with their newer
equivalents.
TEST: TIMELESS-built board images match
Change-Id: I078f9bb3c78f642afc6dcfd64d77be823a4485c2
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46567
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Frans Hendriks <fhendriks@eltan.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
There's no need to have multiple Kconfig symbols which do the same
thing. Introduce `SUPERIO_NUVOTON_COMMON_COM_A` and update boards to use
the new symbol. To preserve alphabetical order in mainboard Kconfig,
place the new symbol above the Super I/O symbol (instead of below).
Change-Id: Ic0a30b3177a1a535261525638be301ae07c59c14
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46522
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
TEST=Build and test booting ADL RVP form NVMe and Optane
localhost ~ # lspci -d :f1a6
Show all the NVMe devices and be really verbose
localhost ~ # lspci -vvvd :f1a6
Print PCIe lane capabilities and configurations for all the NVMe devices.
Change-Id: I0a04b23b17df574d4fa3bae233ca40cd3b104201
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46420
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
A regular M.2 NVMe SSD shows up on RP9 and runs at x4 width.
Optane memory module shows up as 2 NVMe devices in x2 config:
- NVMe storage device uses RP9
- NVMe Optane memory uses RP11
Note: These two devices are sharing CLK PINs because of same M.2 slot.
TEST=Build and boot ADL RVP board using Intel Optane card.
Change-Id: Ia21d7d2fd07c4fb32291af7bb5a2e41e40316278
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46419
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
This patch programs GPIO for PCH SSD Power Enable (GPP_D16) and Port
Detect (GPP_A12) as per schematics.
TEST=Able to build and boot ADL RVP.
Change-Id: I015e46bdf25437c6b196deb3e610bc1b58726070
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46417
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
List of changes:
1. Add devicetree.cb config parameters related to FSP-S UPD
2. Configure GPIO as per ADL-P RVP
3. Add files required for ramstage(ec.c, mainboard.c)
4. Add smihandler.c for SMM
5. Add devicetree changes as below
- USB OC PIN programing
- GPE configuration
- SATA port mapping
- LPSS configuration
- Audio configuration
- IA common SoC configuration
- EDP configuration
- TCSS USB configuration
- Enable S0ix
TEST=Able to boot ADL-P RVP without Chrome EC (using on-board EC) with
UART log over legacy UART0 port as 0x3f8 with NVME at RP9 reach till
depthcharge payload.
Change-Id: I120885956c88babfa09d24ce1079d49306919b8a
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46265
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Enables Pcie M.2 support for WWAN and disable M.2 USB.
RP4 is already on and PcieRpEnable[3] is enabled. Clock source 2 is already
configured. Added missing gpio configuration.
BUG=none
TEST=Boot to OS, check WWAN functionality
Change-Id: Ie9b7915062b2ef65d881d478e64322c0b8765614
Signed-off-by: Bora Guvendik <bora.guvendik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45828
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change switches all mainboard devices to use drivers/wifi/generic
instead of drivers/intel/wifi chip driver for Intel WiFi
devices. There is no need for two separate chip drivers in coreboot to
handle Intel and non-Intel WiFi devices since the differences can be
handled at runtime using the PCI vendor ID. This also allows mainboard
to easily multi-source WiFi chips and still use the same firmware
image without having to distinguish between the chip drivers.
BUG=b:169802515
BRANCH=zork
Change-Id: Ieac603a970cb2c9bf835021d1fb0fd07fd535280
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46035
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Duncan Laurie <dlaurie@chromium.org>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
Refer to commit d7b88dc (mb/google/x86-boards: Get rid of power button
device in coreboot)
This change gets rid of the generic hardware power button from all
intel mainboards and relies completely on the fixed hardware power
button.
Change-Id: I8f9d73048041d42d809750fdb52092f40ab8f11f
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/46268
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Furquan Shaikh <furquan@google.com>
It builds same binary for intel/d945gclf using BUILD_TIMELESS=1
Change-Id: Ic48008719a9cf6942ae8cdaebaab6ba43e665489
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45281
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch moves platform.asl into common block acpi directory to
avoid duplicating the same ASL code block across SoC directory.
TEST=Able to build and boot TGL, CNL and CML platform.
1) Dump and disassemble DSDT, verify _PIC method present inside
common platform.asl is still there.
2) Verify no ACPI error seen while running 'dmesg` from console.
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Change-Id: I5189b03d6abfaec39882d28b40a9bfa002128be3
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45982
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Move and use the common xeon_sp/cpx/acpi asl for skx/.
There were only minor whitespace differences between the directories.
Update the mainboards to build the moved files.
TiogaPass coreboot.rom checked with BUILD_TIMELESS.
Change-Id: I5058a3fe8d96075a266fb92f10707bb94308c85b
Signed-off-by: Marc Jones <marcjones@sysproconsulting.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45217
Reviewed-by: HAOUAS Elyes <ehaouas@noos.fr>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Jay Talbott <JayTalbott@sysproconsulting.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
- Enable DDC pins for DDI-B
- Enable HPD pins for DDI-1/DDI-2
- Update MPHY/USB2 Mapping to match with the TGL-Y RVP schematic
BUG: System not able to detect displays attached to onboard micro-HDMI or Type-C connectors
TEST: hot-plug/unplug HDMI displays with onboard micro-HDMI connector and USB Type-C connectors to make sure the displays get detected and enabled
Change-Id: I08a1b16a8fa45cf0f366661395b9f2aa25c44935
Signed-off-by: Jason Le <jason.v.le@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45016
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This change allows treating the PMC as a 'hidden' PCI device on
JasperLake, so that the MMIO & I/O resources can be exposed as
belonging to this device, instead of the system agent and LPC/eSPI.
Original patch for jasperlake SoC here:
CB:42018
This change was missing for JasperLake rvp board.
TEST=Checked PMC init function is called and also checked PCI resource
for PMC device 1f.2.
Change-Id: I7531d32c62d3f9735938f744f2892ab9c9bebddf
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45793
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Add DTT (Dynamic Tuning Technology) support for Tiger Lake based rvp board.
Set power limits and CPU sensor thresholds for DTT based thermal control.
BRANCH=None
BUG=None
TEST=Build and boot on tglrvp board
Change-Id: I0dbee370b8dc9e1e3ae6f1a1101047ac6fd76f53
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45291
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
The name GENERIC_SPD_BIN doesn't reflect anymore what that config is
used for, so rename it to HAVE_SPD_BIN_IN_CBFS.
Change-Id: I4004c48da205949e05101039abd4cf32666787df
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45147
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Enable processor thermal control using PCI dev path function instead of
Device4Enable parameter in devicetree. This change removes the dependency
on Device4Enable in devicetree. We can enable and disable this thermal
control using on and off support with PCI device entry in devicetree.
BRANCH=None
BUG=None
TEST=Built and tested on dedede board
Change-Id: I0463236996ad001af506c9966840b27fe44d60d2
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45454
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
CSE Lite SKU is CSE FW designed for Chrome and this enables CSE Lite SKU
support for tglrvp.
BUG=None
TEST=Build and boot tglrvp with CSE Lite and Consumer SKU
Change-Id: Ia5f3e8125b5e7760a62f7fb46aeeae85c32e2037
Signed-off-by: Jamie Ryu <jamie.m.ryu@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41132
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Reviewed-by: Shreesh Chhabbi <shreesh.chhabbi@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This is to enable Intel ME communication interface HECI1 by
devicetree for PAVP with CSE Lite.
PAVP feature is enabled with CSE Lite SKU for Chrome and HECI1 interface
is required between kernel and CSE Lite.
BUG=None
TEST=Build and boot tglrvp. Run lspci and check pcie device
00:16.0 Communication controller: Intel Corporation Device a0e0
Change-Id: I23117fa96503942e6a72765dd3fd1cc762e3f705
Signed-off-by: Jamie Ryu <jamie.m.ryu@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42307
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Enable CSE PCI device Bus 0: Device 0x0f: Function 0x00 to let
Intel common cse block code can use this device.
Calling me_read_config32(offset) function from ramstage:
Without this CL :
HECI: Global Reset(Type:1) Command
BUG: me_read_config32 requests hidden 00:0f.0
PCI: dev is NULL!
With this CL :
HECI: Global Reset(Type:1) Command
HECI: Global Reset success!
Signed-off-by: Subrata Banik <subrata.banik@intel.com>
Change-Id: I97d221ae52b4b03ecd859d708847ad77fe4bf465
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45469
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Mario Scheithauer <mario.scheithauer@siemens.com>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-by: Michael Niewöhner <foss@mniewoehner.de>
This allows us to drop some casts to uintptr_t around the tree.
The MCHBAR32 macro still needs a cast to preserve reproducibility.
Only the native raminit path needs the cast, the MRC path does not.
Tested with BUILD_TIMELESS=1, these boards remain identical:
- Lenovo ThinkPad X230
- Dell OptiPlex 9010
- Roda RW11 (with MRC raminit)
Change-Id: I8ca1c35e2c1f1b4f0d83bd7bb080b8667dbe3cb3
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45349
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
RCBA is located in the PCH. Replace all instances with the
already-defined `DEFAULT_RCBA` macro, which is equivalent.
Change-Id: I4b92737820b126d32da09b69e09675464aa22e31
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45348
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Both Gemini Lake boards in the tree use the same value.
Change-Id: Ib6bd05206026736fd7e3d44b49e4d8ba217c2708
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45142
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Add DTT (Dynamic Tuning Technology) support for Jasper Lake based rvp board.
Set power limits and CPU sensor thresholds for DTT based thermal control.
BRANCH=None
BUG=Noe
TEST=Build and boot on jslrvp board
Change-Id: I41409c70d8472c54ca452fc98d5ee9edf3ccd307
Signed-off-by: Sumeet R Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44942
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Drop duplicated code for spd.bin generation that is provided globally
in lib/Makefile.inc.
For all affected boards it has been verified that the output binary
functionally matches the original one. The changed execution order of
Make instructions influenced the cbfs file order. Hence, the rom images
can't be compared directly.
Thus, the output files of the two timeless abuild runs have been compared.
Further, it was verified that the final files in cbfs stay identical, by
comparing the extracted cbfs of each board.
The boards (possibly) needing modification could be found with something
like this (with false positives, though):
find src/mainboard -name Makefile.inc | \
xargs egrep 'SPD_BIN|SPD_DEPS' | cut -d: -f1 | sort -u
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Change-Id: Icd3ac0fd6c901228554115c6350d88bb49874587
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44774
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
Setting USBx_PORT_EMPTY is not a requirement anymore, since unset
devicetree settings default to 0 and the OC pin now only gets set when
the USB port is enabled (see CB:45112).
Thus, drop the setting from all devicetrees.
Change-Id: I899349c49fa7de1c1acdca24994ebe65c01d80c6
Signed-off-by: Michael Niewöhner <foss@mniewoehner.de>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/45125
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Felix Singer <felixsinger@posteo.net>
Since there are 4 different versions of FSPs for the Comet Lake
platform, add a new Kconfig option for the currently used SoC being able
to differ between the various SoCs and FSPs.
The new Kconfig option selects the Comet Lake SoC as base for taking
over its specific configuration and is only used for configuring the
path to its specific FSP header files and FSP binary.
Also, adjust all related mainboards so that their Kconfig selects the
new option.
For details, please see
https://github.com/intel/FSP/tree/master/CometLakeFspBinPkg
Built System76/lemp9 with BUILD_TIMELESS=1 before and after this patch
and both images are equal.
Change-Id: I44b717bb942fbcd359c7a06ef1a0ef4306697f64
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44952
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
GENERATE_SMBIOS_TABLES is already set to yes at src/Kconfig
Change-Id: I2845f4f329283360a49ea40dfee7d9a232ab4ea1
Signed-off-by: Elyes HAOUAS <ehaouas@noos.fr>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44927
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
Includes changes related to GPIO pad to configure I2C4 required for UFC
Change-Id: Ica3ac31f10214b8aff3bb64a2c3b42ccfa28bdcd
Signed-off-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44671
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Reviewed-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Jasper Lake SoC had PCI root port mapping swap, thats why we were
using swapped mapping earlier for all the boards
Recently, patch was pushed to handle this swap in PCI enumeration code
for Jasper Lake and we need to correct this mapping. Now this mapping
aligns with actual port mapping in the schematics
BUG=None
BRANCH=None
TEST=NVMe and WLAN are getting detected after this changes
Change-Id: Ide5f8419a15f559cefeb6039f155fabf97c279f8
Signed-off-by: Maulik V Vaghela <maulik.v.vaghela@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44391
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
More space is required in the COREBOOT CBFS to accommodate some features.
Currently no alternate firmware is stuffed into RW_LEGACY CBFS and has
~1 MB of unused space. Borrow some space from RW_LEGACY CBFS and extend
the RO_SECTION. Even within RO_SECTION, GBB requires only 12 KiB. So
adjust the GBB region accordingly and extend the COREBOOT CBFS.
BUG=b:162159386
TEST=Build the JSLRVP mainboard.
Change-Id: Ia8bb381c31ddf76f3211f9d4ac5c8c18c27834b7
Signed-off-by: Karthikeyan Ramasubramanain <kramasub@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44283
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Justin TerAvest <teravest@chromium.org>
This patch updates the SLP_Sx assertion widths and power cycle duration
for the Japerlake RVP.
Power cycle duration:
With default value,
S0->S5 -> [ ~4.2 seconds delay ] -> S5->S0
With value set to 1,
S0->S5 -> [ ~1.2 seconds delay ] -> S5->S0
BUG=b:159104150
TEST=Verified that the power cycle duration is ~1.2s with global
reset on JSLRVP.
Change-Id: Ie2a8d959d7ebbf9c24f8c4e8d5c68b70e0ac5708
Signed-off-by: V Sowmya <v.sowmya@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43793
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-by: Ronak Kanabar <ronak.kanabar@intel.com>
Reviewed-by: Aamir Bohra <aamir.bohra@intel.com>
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
This patch sets the GPP_H1 to PAD_CFG_GPO which is general
purpose output with no pullup/down. We need this GPIO for
the detection of soundcard in TGL RVP's.
BUG=none
BRANCH=none
TEST=Build and boot tglrvp successfully. From "aplay -l"
output check that soundcards are listed properly.
Change-Id: Ic0ef33079af7940360c986efacabd6d367aad516
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41811
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nick Vaccaro <nvaccaro@google.com>
Interrupt _CRS is missing under CREC scope. TGLRVP U/Y has GPP_A15
assigned to MECC_HPD2 as EC_SYNC_IRQ. Configure this GPP_A15 GPIO as
active low and level interruptible for EC sync interrupt configuration.
BUG=None
TEST=Booted to kernel and verified EC_SYNC_IRQ in the scope of CREC
current resource settings.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: Idfe4d4e800866805ee8d758028ac7ddf4b259faa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44103
Reviewed-by: Vijay P Hiremath <vijay.p.hiremath@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Also remove the meaningless `sata_traffic_monitor` devicetree option.
Function parameters will be removed in a reproducible follow-up.
Change-Id: I70cf1e06cc8ace504a22be9f9c4441e3070f9e29
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44336
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Currently, CIO gets enabled by the option Cio2Enable, but this
duplicates the devicetree on/off options. Therefore, depend on
the devicetree for the enablement of the CIO controller.
All corresponding mainboards were checked if the devicetree
configuration matches the Cio2Enable setting, and missing entries
were added.
Change-Id: I65e2cceb65add66e3cb3de7071b1a3cc967ab291
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44032
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently, SA IMGU gets enabled by the option SaImguEnable,
but this duplicates the devicetree on/off options. Therefore, depend on
the devicetree for the enablement of the SA IMGU controller.
All corresponding mainboards were checked if the devicetree
configuration matches the SaImguEnable setting, and missing entries
were added.
Change-Id: I293a20a321c75f82a57cbd5339656d93509b7aa6
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44031
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
Currently, SDXC gets enabled by the option ScsSdCardEnabled,
but this duplicates the devicetree on/off options. Therefore, depend on
the devicetree for the enablement of the SDXC controller.
All corresponding mainboards were checked if the devicetree
configuration matches the ScsSdCardEnabled setting, and missing
entries were added.
Change-Id: I298b7d0b0fe2a7346dbadcea4be22dc67fce4de8
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44028
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
Currently SA thermal subsystem gets enabled by the option Device4Enable,
but this duplicates the devicetree on/off options. Therefore depend on
the devicetree for enablement of the SA thermal subsystem controller.
All corresponding mainboards were checked if the devicetree
configuration matches the Device4Enable setting, and missing entries
were added.
Change-Id: I7553716d52743c3e8d82891b2de14c52c6d8ef16
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44026
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently HECI1 gets enabled by the option HeciEnabled, but this
duplicates the devicetree on/off options. Therefore use the on/off
options for the enablement/disablement of the HECI1 device.
All corresponding mainboards were checked if the devicetree matches
the HeciEnabled setting, and adjusted where necessary.
Change-Id: I03dd3577fbe3f68b0abc2d196d016a4d26d88ce5
Signed-off-by: Felix Singer <felix.singer@secunet.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44177
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
RVP11 and RVP3 set it to zero, the other two omit the setting.
Tested with BUILD_TIMELESS=1, all four variants do not change.
Change-Id: I6b393f0f2269f62b415456c17ba5962f46a1c5d1
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43909
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
RVP8 does not set it, and the other variants set it to zero. So, factor
it out.
Tested with BUILD_TIMELESS=1, all four variants do not change.
Change-Id: I67c958af2dc955d07b895dc93fbe2232dbd48d34
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43908
Reviewed-by: Subrata Banik <subrata.banik@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This change updates devicetree to enable SSDT generation for world
facing and user facing cameras of jasperlake_rvp. Also removes DSDT
changes related to the world facing camera.
Change-Id: Ib439572bc1d15ef02c86c7bfa88af6b16eb06f97
Signed-off-by: Sugnan Prabhu S <sugnan.prabhu.s@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41758
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Some UPD options are already set in `xeon_sp/cpx/romstage.c`. Remove
them from the board configuration to avoid duplicating this code.
Change-Id: Ic79245103c33427e06c7ea881be778e3d219c45f
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43924
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
According to src/vendorcode/intel/fsp/fsp2_0/cooperlake_sp/FspmUpd.h,
use FSP_M_CONFIG structure fields to configure UPD options for FSP-M
in romstage instead of raw offsets.
Change-Id: Idb25d8954b09805b496ab97b341a8ef1ac38bb6a
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43923
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
The only reason to use a named choice statement is if you plan on
having the choice statement in multiple places. Since the `TGL_EC`
name is not used anywhere else, we might as well get rid of it.
Change-Id: Ic0bddefd007ef961bbff61fd656475cae78148e2
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43836
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
It is expected both of TCSS D3Hot and D3Cold are enabled by default.
BUG=None
TEST=Verified both of TCSS D3Hot and D3Cold configuration on TGLRVP.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: Id569d8191f82f12379b57a9c50aec31776220bb5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/44003
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Divya S Sasidharan <divya.s.sasidharan@intel.com>
Reviewed-by: Ravishankar Sarawadi <ravishankar.sarawadi@intel.com>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Currently HDA gets enabled by the option EnableAzalia, but
this duplicates the devicetree on/off options. Therefore use
the on/off options for the enablement of the HDA controller.
I checked all corresponding mainboards if the devicetree configuration
matches the EnableAzalia setting.
Change-Id: Id20d023b2f286753fb223050292c7514632e1dd3
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43866
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently HECI3 gets enabled by the option Heci3Enabled, but
this duplicates the devicetree on/off options. Therefore use the
on/off options for the enablement of the HECI3 controller.
I checked all corresponding mainboards if the devicetree configuration
matches the Heci3Enabled setting.
Change-Id: I4f99d434dfee49a9783e38c3910b9391d479cb83
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43864
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Currently eMMC gets enabled by the option ScsEmmcEnabled, but this
duplicates the devicetree on/off options. Therefore use the
on/off options for the enablement of the eMMC controller.
I checked all corresponding mainboards if the devicetree configuration
matches the ScsEmmcEnabled setting.
Change-Id: I3b86ff6e2f15991fb304b71d90c1b959cb6fcf43
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43862
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
Currently SMBus gets enabled by the option SmbusEnable, but this
duplicates the devicetree on/off options. Therefore use the on/off
options for the enablement of the SMBus controller.
I checked all corresponding mainboards if the devicetree configuration
matches the SmbusEnable setting.
Change-Id: I0d9ec1888c82cc6d5ef86d0694269c885ba62c41
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43845
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
Currently LAN gets enabled by the option EnableLan, but this
duplicates the devicetree on/off options. Therefore use the on/off
options for the enablement of the LAN controller.
I checked all corresponding mainboards if the devicetree configuration
matches the EnableLan setting.
Change-Id: I36347e8e0f0ddba47aec52aeb6bc047e3c8bfaa4
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43844
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
Reviewed-by: Patrick Rudolph <siro@das-labor.org>
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Currently SATA gets enabled by the option EnableSata, but this
duplicates the devicetree on/off options. Therefore use the on/off
options for the enablement of the SATA controller.
I checked all corresponding mainboards if the devicetree configuration
matches the EnableSata setting.
Change-Id: I217dcb7178f29bbdeada54bdb774166126b47a5a
Signed-off-by: Felix Singer <felixsinger@posteo.net>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43843
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
This change updates TGLRVP configuration to have USB Type-C connector
device properties filled into ACPI SSDT.
TEST=Built and booted to kernel on tglrvp boards. Verified the USBC
scope under LPCB.EC0.CREC with required connector device properties.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: Ifd4c59afb3b8a222598fd4ff36d72c4b877bdad2
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43893
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Two usb Type-C ports under the actual mux device. Each port has its own
ACPI device entry. These nodes are the ones that the USB Type-C
port/connector device will refer to in order to configure the mux.
TEST=Built image-tglrvp-up4.bin successfully.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I8423ddbb5bc189899a9e19e7da6e2ee7b7fecc18
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43412
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
All boards disable PIRQs, except purism/librem_bdw. Since IRQ0 is
invalid and modern OSes don't use PIRQ routing, disable the PIRQs.
Change-Id: I93b074474c3c6d4329903cab928dc41e1d3a3fb3
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43868
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
All boards disable PIRQs. They aren't used on modern OSes anyway.
Change-Id: I1351fd4a3910e8cf2e9afe51dc2e82c7464de403
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43863
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Fixes a bug in Makefile.inc, which did not allow building ROM image
with ramstage.c from motherboard configuration.
Change-Id: I70d8a2e1f53e2fa56d514361116a55f175407753
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43457
Reviewed-by: Andrey Petrov <andrey.petrov@gmail.com>
Reviewed-by: Lance Zhao
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
If bit 7 of a PIRQ route is set, it is disabled. Modern OSes don't use
PIRQ routing, so we might as well zero the other bits for consistency.
Tested on Asrock B85M Pro4 with SeaBIOS 1.13.0, still boots.
Change-Id: I78980b9ea5e878a6200df0f6c18c5e7d06a7950a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43861
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
The Kconfig lint tool checks for cases of the code using BOOL type
Kconfig options directly instead of with CONFIG() and will print out
warnings about it. It gets confused by these references in comments
and strings. To fix it so that it can find the real issues, just
update these as we would with real issues.
Signed-off-by: Martin Roth <martin@coreboot.org>
Change-Id: I5c37f0ee103721c97483d07a368c0b813e3f25c0
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43824
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
- Update MAINBOARD_PART_NUMBER for TGL variants
- MAINBOARD_PART_NUMBER is reported as FRID on acpi
- This is required for cros_config to differentiate
across TGL variants.
- Mosys uses cros_config to identify TGL variants using
data read from FRID
Bug=none
Test=build and boot coreboot on TGLRVP UP3 hardware
Signed-off-by: Anil Kumar <anil.kumar.k@intel.com>
Change-Id: I11d4ab2a5b6ade6c50988a9fec4d9866fe79d7b5
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43620
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Jack Rosenthal <jrosenth@chromium.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Put them in common code just in case something depends on the values.
Change-Id: Ief526efcbd5ba5546572da1bc6bb6d86729f4e54
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43851
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Arthur Heymans <arthur@aheymans.xyz>
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
According to the documentation [1], RX Level/Edge Configuration (trig)
and GPIO Tx/Rx Buffer Disable (bufdis) [2] settings are not applicable
in native mode and BIOS does not need to configure them. Therefore,
there is no need to configure this in gpio.h using PAD_CFG_NF_BUF_TRIG
macros. Use PAD_CFG_NF instead and set this fields to 0.
[1] Intel document #549921
[2] Intel document #336067-007US
This is part of the patch set
"src/mb/*, src/soc/intel/common/gpio: Remove PAD_CFG_NF_BUF_TRIG ":
CB:43455 - cedarisland: undo set trig and bufdis for NF pads
CB:43454 - tiogapass: undo set trig and bufdis for NF pads
CB:43561 - h110m: undo set trig and bufdis for NF pads
CB:43569 - soc/intel/common/gpio_defs: Remove PAD_CFG_NF_BUF_TRIG
Change-Id: Ie3ee2eadc08826d49e8517c83ab6831398e3aa93
Signed-off-by: Maxim Polyakov <max.senia.poliak@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43455
Reviewed-by: Michael Niewöhner
Reviewed-by: Lance Zhao
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This patch enables the SkipCpuReplacementCheck config for jasperlake rvp
to avoid the forced MRC training with the soldered down SOC.
BUG=b:160201335
BRANCH=None
TEST=Build and verify on jasperlake rvp with CSE Lite SKU.
Cq-Depend: chrome-internal:3142530
Change-Id: I40fb9a25170e8db3c63a71428ba459160a918961
Signed-off-by: Krishna Prasad Bhat <krishna.p.bhat.d@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43146
Reviewed-by: Karthik Ramasubramanian <kramasub@google.com>
Reviewed-by: Sridhar Siricilla <sridhar.siricilla@intel.com>
Reviewed-by: Rizwan Qureshi <rizwan.qureshi@intel.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Make it default to 0x400, which is what the touched southbridges use.
Change-Id: I95cb1730d5bf6f596ed1ca8e7dba40b6a9e882fe
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43037
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Nico Huber <nico.h@gmx.de>
This change adds SMI handler for SCI, S3/S5 wake up and LID closed
events on tglrvp platform.
TEST=Built image and booted to kernel.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: I0bc72f164e86f1921e0cad39f9749e8e3be0778f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42957
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
This change allows EC to change state of host-controlled USB MUX.
TEST=Built image and booted to kernel.
Signed-off-by: John Zhao <john.zhao@intel.com>
Change-Id: Ia7c331157b1b4039e42c373f5b130a66f7594458
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42955
Reviewed-by: Caveh Jalali <caveh@chromium.org>
Reviewed-by: Tim Wawrzynczak <twawrzynczak@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Share "EC in RW" GPIO with depthcharge. Also we define the CONFIGS
needed CHROME, CHROME_EC and use the chrome lid and recovery.
BUG=None
BRANCH=None
TEST=Build and boot TGL RVP. Check recovery works with
crossystem recovery_request.
Change-Id: I1e88200e3f8418e5b0ab39ac65ed1b3545ce111e
Signed-off-by: Shaunak Saha <shaunak.saha@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/40861
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
Reviewed-by: Srinidhi N Kaushik <srinidhi.n.kaushik@intel.com>
Enable CpuReplacementCheck for TGLRVP with a CPU socket.
Test=build and verified with tglrvp
Change-Id: I75b4a4609c172c341087077228e23c6d31a9e7e1
Signed-off-by: Jamie Ryu <jamie.m.ryu@intel.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42789
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Wonkyu Kim <wonkyu.kim@intel.com>
There's no generic way to tell whether a mainboard has an EC or not.
Making Kconfig symbols for these options seems overkill, too. So, just
put them on the devicetree. Also, drop unnecessary assignments when the
board's current value is zero, as the struct defaults to zero already.
Change-Id: If2ebac5fcab278c97dfaf8adc9d1e125888acafe
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43129
Reviewed-by: Nico Huber <nico.h@gmx.de>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
And use it instead of directly writing to the MRC struct.
Change-Id: I7f04db29a08512c1a8b2b2300dba71cb3b84a5c5
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43127
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Check the PCH's LPC device ID to know the system type instead of relying
on hardcoded numbers. The `get_pch_platform_type` function is MRC-safe.
Change-Id: Icfe7c2dccb7c7a178892ad3a2e34ca93b33b2bb9
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43124
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Several of these includes are no longer necessary. Get rid of them.
Since "raminit.h" already includes "pei_data.h", we can omit including
the latter for brevity's sake.
Change-Id: Ia7e9dadf87114ca9ea4761b89909ea035cdfc38a
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43121
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
All mainboards have a non-zero SPD address to implemented DIMM slots.
Knowing this, it is possible to compute the MRC slot population masks
automatically instead of hardcoding the values on each mainboard.
Change-Id: Ia8f369dd1228d53d64471e48700e870e01e77837
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43119
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Reviewed-by: Michael Niewöhner
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
This is what sandybridge does, and if done properly allows factoring out
common settings. Said refactoring will be handled in subsequent commits.
Change-Id: I075eba1324a9e7cbd47e776b097eb940102ef4fe
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43108
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
The DxxIR (Device xx Interrupt Route) registers in RCBA are 16-bit wide,
so do not use 32-bit operations to program them.
Note that the DxxIP (Device xx Interrupt Pin) registers are 32-bit, so
using 32-bit operations on them is correct.
Change-Id: I9699b98d5fcd26b2c710bf018f16acc65dcb634e
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43107
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
It only contains a pointer to another struct. Flatten it.
Change-Id: Iab427592c332646e032a768719fc380c5794086b
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43106
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
Instead of using function pointers, we can use weak functions. So, drop
the pointer from `romstage_params`, leaving `pei_data` as the only
remaining member. This will be cleaned up in a follow-up commit.
Change-Id: I3b17d21ea7a650734119a5cab4892fcb158b589d
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43105
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Patrick Georgi <pgeorgi@google.com>
This code is not even being build-tested. Drop it before it grows moss.
Change-Id: I6948a0b9a6b699cb44e3e02d9e134180bac2fa14
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43239
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Michael Niewöhner
This simplifies things and makes type checking possible.
Change-Id: Iefc9baabae286aac2f2c46853adf1f6edf01586f
Signed-off-by: Angel Pons <th3fanbus@gmail.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43103
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Tristan Corrick <tristan@corrick.kiwi>
