while I'm at it (trivial).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2839 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Hence the default position for the VGA bios should also assume a 1MB rom chip, instead of a 512KB chip.
Signed-off-by: Ward Vandewege <ward@gnu.org>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2792 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
(or at least most) mainboards. This should put and end to
copy-paste'ing the same file again and again for every mainboard.
Fix the build for the MSI MS-6178 target (wrong location of the common
failover.c file).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Corey Osgood <corey.osgood@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2772 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Removed reset.c and added copyright headers.
Remove debug.c. It is not used and should not be here.
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2766 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This is a geode LX board. There are timing settings that are not right
yet, we are still trying to get our board to boot Linux :-)
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2765 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Now uses CAR.
New code for SPD-less memory implementation.
Updated IRQ routing.
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2728 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
the system boot to a command line.
This patch comments out the code to set up the vga framebuffer to allow
the system to boot, without this fix the system hangs during elfboot.
The only line that is absolutely necessary to change is the SMRAM setup,
however I've commented out all vga setup to make it very obvious to both
the kernel/payload and anyone looking at the code that vga isn't
currently working. This setup might also be better handled in
northbridge.c, if it doesn't need to be done before ram init, yet
another reason to comment it all. In the future, LinuxBIOS needs to be
told that the graphics memory area, 1mb or 512kb (at the user or
developer's option), is reserved for the onchip vga, but I'm not sure if
it's taken at the top or bottom of the memory, yet. LB may also need to
set a base address for the AGP aperture and/or be told that range is
reserved as well, whether this was originally the job of the system bios
or vga bios is still a mystery. It also corrects the number of entries
in irq_tables.c, without this fix the kernel would probably complain and
hang due to unmapped IRQs.
Signed-off-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2725 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
more than just one way. This version should be (more) correct.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2723 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
southbridges, along with the Asus MEW-VM. With this, my machine attempts to
boot linux, but does so very slowly and fails during the boot process, probably
because of the irq tables.
Signed-off-by: Corey Osgood <corey.osgood@gmail.com>
Acked-by: Joseph Smith <joe@smittys.pointclark.net>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2719 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The DB800 is the AMD LX Reference Design Kit platform.
For details see: http://www.amd.com/geodelxdb800
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2718 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Both are very similar, thus both use the JUKI-511P target.
Linux with patches from Juergen Beisert
(http://www.linuxbios.org/pipermail/linuxbios/2007-May/020932.html)
boots and work fine (ide, usb, ethernet, serial, keyboard and sound
work normally).
Problems:
- Filo loads a bzImage only from ide0 (ide1 doesn't work yet).
- Video doesn't work, yet.
Signed-off-by: Nikolay Petukhov <nikolay.petukhov@gmail.com>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2716 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Linux booted with the proprietary BIOS reports 2e.f as PS/2 mouse
in the output of 'lspnp -v'.
- The floppy on 2e.f was a typo, should have been 2e.e from the beginning.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2709 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Super I/O part was incorrect.
Also, add ide0_enable/ide1_enable variables, and enable both the
primary and secondary IDE interface per default.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2708 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Only check the RAM from 0 - 640 KB and 768 KB - 1 MB now. That's
available on all boards, regardless of what DIMMs you use.
Tested on the Tyan S1846, works fine.
- Properly set the PAM registers to allow the region from 768 KB - 1 MB
to be used as normal RAM (required for the above).
- Document all of this properly. Add/improve other documentation, too.
- Simplify and document code in northbridge.c.
- Cosmetics and coding style.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2701 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Marc Jones <marc.jones@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2687 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- the Transmeta TM5800 northbridge
- the Densitron DPX114 mainboard (the only one using the TM5800)
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2685 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
hardware, rather than always on at full speed. Set temperature treshold values
to safe defaults, rather than the not-so-safe power-on defaults.
Signed-off-by: Ward Vandewege <ward@gnu.org>
Acked-by: Yinghai Lu <yinghailu@gmail.com>
Acked-by: Ward Vandewege <ward@gnu.org>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2674 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
With CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2=0, 1 million outb():s are used
for timer calibration, which takes about one second.
All EPIA-M boards have timer2 so we use it to boot faster.
Only some EPIA boards have the Nehemiah CPU with timer2 so we default to IO
calibration but add the TSC options so that they can be set in Config.lb.
src/mainboard/via/epia*/reset.c is dead code (entire file within #if 0) so we
set HAVE_HARD_RESET=0 for both boards.
Signed-off-by: Peter Stuge <peter@stuge.se>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2659 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Acked-by: Stefan Reinauer <stepan@coresystems.de>
Signed-off-by: Marc Jones <marc.jones@amd.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2652 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
problems with the asi/mb_5bmlp (trivial).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2644 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
minor changes, to bring them up to par. It also should remove (but might
just clean out) the irq_tables.c from both boards, because they were
just copied from Via Epia to begin with, and weren't usable. As far as I
can tell, these are the only changes needed to the targets for now,
aside from fixups to reset.c when the time comes. Both have been build
tested, but not checked on hardware since I don't have it. I have left
Uwe as the copyright holder since the only changes I've made are trivial.
Signed-off-by: Corey Osgood <corey_osgood@verizon.net>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2642 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
the IGEL Winnet III thin client.
It boots a Linux kernel, but there are some problems. The login
prompt is never reached, it simply hangs at some point.
One possible reason is the IRQ table, which needs fixing.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2641 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
the 5c register in the southbridge so that interrupts are routed
correctly.
With this patch, ethernet works quite well.
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2640 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
adds a symbol to the model_lx/cache_as_ram.inc, and modifies some
files in the mainboard directory. This patch has been tested but there
is a remaining problem which I am tracking down. Expect one more patch
to "get it all working".
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2638 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Ronald G. Minnich <rminnich@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2636 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
I'm self-acking as this is pretty trivial. I tested both a normal build
and an abuild-run, and nothing breaks.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2635 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
broke and stopped FILO
from being able to boot.
The fix is a simple one line change plus a comment to
src/mainboard/via/epia/auto.c to write to the IDE
configuration register 0x42 . This has always been done here, however
at some point
something broke it.
The same register was also being set correctly in ide_init(), however
for some reason
this does not work. Possibly the register needs to be set before the IDE
peripheral is enabled
or maybe it is a timing issue.
The section of code in ide_init() (
src/southbridge/via/vt8231/vt8231_ide.c ) that does
write to register 0x42 has been commented out as it is superfluous
and I have added a comment to indicate the reason, should someone at a
future date wonder
why.
I have also changed the default COM speed from 19200 to 115200 in
src/mainboard/via/epia/Options.lb
There has been mention before about the EPIA board not being able to use
115200 but I have seen
no such problems with my board.
Signed-off-by: Ben Hewson <ben@hewson-venieri.com>
This patch worked for me and allowed me to boot Debian kernel
2.5.16-4-486 on an epia 800 mhz system. It is able to consistently get
through the initialization and start init now.
However, after that it crashes at various points in the boot process.
Acked-by: Alex Mauer <hawke@hawkesnest.net>
Note from comitter: I am commiting this, although:
1. it's not the exact right way to fix it up, the chip.h for the sb
should change
2. Alex reports problems, which are almost certainly memory issues.
But it is as close as we've gotten. I can't test it.
Ron Minnich
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2633 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Geode changes.
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2632 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
based on the Geode LX processor. The Norwich is the canonical
Geode reference, and will server as a good basis for other
Geode based platforms.
Signed-off-by: Marc Jones <marc.jones@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2629 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
as that is not RAM but used for other stuff.
First try at PCI init added to src/mainboard/tyan/s1846/Config.lb.
Use a real payload (FILO) per default now.
Note: this cannot boot a payload, yet, but it gets a lot further now.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2623 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Comment out code which currently doesn't compile. Needs fixing later.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2614 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Drop AMD prototype mainboards that were for internal testing &
validation use only.
Note: These boards could never be purchased. No reasons to worry.
Questions welcome via private mail.
Signed-off-by: Yinghai Lu <yinghai.lu@amd.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2609 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
abuild with a payload. Trivial
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2608 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
artecgroup/dbe61
Add CONFIG_COMPRESSED_PAYLOAD_NRV2B to Options.lb since it's used in
Config.lb.
Change default for CONFIG_PCI_ROM_RUN to 1 so VGA ROM can run.
technologic/ts5300
Removed CONFIG_CONSOLE_VGA, the embedded board has no VGA without the
development addon card anyways.
Changes to target Config.lb so it actually builds.
Signed-off-by: Peter Stuge <peter@stuge.se>
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2607 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
* going back to old board specific dsdt for agami aruma.
This is hopefully dropped again some day, but until then
here's a working solution.
* Some minor Agami specific changes.
* drop obsolete bringup workaround hyperclocking.diff
* increase image size again, x86emu wants it.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2606 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
* Drop empty file (0 bytes) northbridge/amd/amdk8/cpu_rev.c
and references to it.
* move config option decision to preprocessor instead of code
since config options can not change during runtime
* slightly more verbose output in built_opt_tbl.c
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2586 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
It's not fully working, among other things because the Intel
440BX northbridge isn't working, yet.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2580 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This is pretty trivial, as it was correct in the original non-CAR code.
Suddently, CAR works nicely.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2572 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
It does the ROM_STREAM -> PAYLOAD rename that afaik was done after
Yinghai sent his work to legal, so it is required to get that code
building.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Peter Stuge <peter@stuge.se>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2561 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2557 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
* Nvidia l1_2pvv
* Gigabyte m57sli
* Supermicro h8dmr
* Tyan s2912 -- with HTX
The boards will currently _not_ compile, two further patches
from Yinghai Lu are still missing. Please be patient :)
Signed-off-by: Yinghai Lu <yinghai.lu@amd.com>
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2554 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
most people.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2545 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Luis Correia <luis.f.correia@gmail.com>). The code is loosely based on
the Eaglelion 5bcm mainboard.
Warning: this is work in progress!
As of now, it does boot with serial console only (no vga), and two ethernet
cards work sometimes. This has to do with the IRQ assignments, which are a
complete mess. USB is now apparently working, but I can't make any device
to be recognized.
The PCI slot is still unusable due to the IRQ thing.
Audio, other serial ports, irda, floppy and paralell port support is
unknown aka untested yet.
(closes#32)
Signed-off-by: Luis Correia <luis.f.correia@gmail.com>
Acked-by: Acked-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2508 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
pmtools packages of upcoming SUSE 10.2, too, so the problem will
go away. (new package installed on linuxbios.org, too)
See also
http://www.linuxbios.org/pipermail/linuxbios/2006-September/015968.html
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2498 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
and leaving enough room for a real payload (not /dev/null)
This is a wonderful example why "uses" sucks.
* add Config-abuild.lb for those boards that dont build with
the default settings and a real payload:
arima/hdama, amd/quartet, amd/serengeti_cheetah, ibm/e326
* if lzma is installed and a real payload is used, try compressing
it.
* fix a small bug in "abuild --help"
This patch is acked by me because its due to infrastructural changes only.
Flames welcome.
Signed-off-by: Stefan Reinauer <stepan@coresystems.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2496 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
same format for all CHIP_NAME() entries in LinuxBIOS (Closes#20).
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@linuxbios.org>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2490 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
long time and I could not get into the tracker.
These are patches to enable ms9185 support. Abuild passes.
Signed-off-by: bxshi <bxshi@msik.com.cn>
Acked-by: Ronald G. Minnich <rminnich@gmail.com>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2486 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Richard Smith <smithbone@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2483 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
will then rename the E7520 and E7525 directories respectively.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2477 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
and (hopefully) the correct canonical name of the vendor and board.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2476 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
will then rename the src/superio/NSC directory to src/superio/nsc.
Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2472 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
me fix this before committing first.
Signed-off-by: Yinghai Lu <yinghailu@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2469 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
another commit is following
Signed-off-by: Yinghai Lu <yinghailu@gmail.com>
Acked-by: Stefan Reinauer <stepan@coresystems.de>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2468 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
add devices for the lx and artecgroup/dbe61
point artecgroup at cs5536_lx as it is so different.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2420 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Signed-off-by: Carl-Daniel Hailfinger
Signed-off-by: Ronald G. Minnich
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2413 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
USB P4 is disabled by default and we need to setup the mux bits proper
to make it work. This is the frame work for that. All thats needed
is the right address values
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2387 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
amd gx2 north -- don't set anything in the north, it conflicts with vsa
settings. So we have our own pci_set_resources that is essentially a
no-op -- just calls the kids.
olpc rev_a config -- DISABLE the compressed rom stream. This SHOULD NOT
have been set -- it is untested and caused real trouble.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2369 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
* src/cpu/amd/model_lx/model_lx_init.c
L2 cache initialization removed (moved to northbridge.c)
* src/include/cpu/amd/lxdef.h
more checked values
* src/northbridge/amd/lx/northbridge.c
L2 cache initialization added
cpubug() commented out
* src/northbridge/amd/lx/raminit.c
empty function sdram_set_registers() is in use, don't remove
* src/mainboard/artecgroup/dbe61/Config.lb
irqmap changes
* src/mainboard/artecgroup/dbe61/irq_tables.c
tentative changes to irq table (currently not in use)
* src/mainboard/artecgroup/dbe61/mainboard.c
irq assigned manually to NIC
* src/mainboard/artecgroup/dbe61/Options.lb
gcc 4.0 is OK
* targets/artecgroup/dbe61/Config.lb
64K for VSA is OK at moment
Signed-off-by: Indrek Kruusa <indrek.kruusa@artecdesign.ee>
Signed-off-by: Andrei Birjukov <andrei.birjukov@artecdesign.ee>
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2360 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
read code. SBbus reads to RAM now work. Yah!
- Rename the register constants to something I can look at
more easily.
- Make the logic flow match the flow from V1 assembly
- #if 0 out other SMbus functions that are still broken.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2353 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Re-enable the SPD dump routine in this Bitworks/IMS code and make
it work like the Asus/p2b. This avoids having to hack the
sdram/generic_dump_spd.c for a single mem controller.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2352 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- New superIO winbond/w83977tf
- Add single memory controller SBbus debug routine
into a file private to the i440bx
This adds support the start of support for an Asus p2b
mainboard. Current limitations are the same as for the
Bitworks IMS board. Reads from the SMbus don't work.
Moving dump_spd_registers() into its own private copy
solves the problem of having to go hack on the version that
included in src/sdram to only do one memory controller.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2351 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
There is one global change to pci_ids.h. The rest are changes for LX. I
ran abuild and it is ok. Not all artec design changes are included as
some of them would adversely affect other mainboards. Indrek will need
to test.
Signed-off-by: Ron Minnich
Signed-off-by: Indrek Kruusa, indrek.kruusa@artecdesign.ee, artec
design.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2350 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
add support for NSC pc87351 SuperIO
add Bitworks/IMS manboard config
This is a very basic framework for the i440bx chipset and the
Bitworks IMS board that uses it. Most things are
structure only.
Known issues:
- SMbus reads to the RAM SPD come back
all zero.
- dump_spd_registers() is commented out since it breaks with
the default setting of generic_dump_spd.c where it wants
2 memory controllers.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2347 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
disabled.
cs5536: add new entires for SB control etc.
cs5536.c: chip_enabled function moved to chip_init, so it only gets run
once.
IRQ setup improved
gx2def.h: new defines added
vr.h: new file, with new def's for virtual register control.
mainboard config.lb: new entries added for nb and sb control.
chipsetinit.c: new controls added -- I forget all the details :-)
grphinit.c: new function added
northbridge.c: new IRQ control added. FlashChipSetup added, controlled
by chip info setupflash struct member. Currently, if enabled, this hangs
OLPC in linux PCI scan.
chip.h: new struct members added for unwanted device enable, flash setup
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2345 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
breaking a build is intentional. It will be fixed in a bit.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2338 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
manage them. Make pci_level_irq global. Add value settings for OLPC
rev_a board. Comment out no-longer-needed code in olpc mainboard.c
-- it is replaced by the settings in Config.lb, and the support
in cs5536.c
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2328 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
olpc and rumba can now boot linux out of flash. vsa was resized to 64K.
olpc and rumba now used compressed payload -- thanks stefan!
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2307 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Default is 255.
This allows mainboard configs for working across various groups
of boards that differ a device that may not loaded.
If you search for a device that is not loaded and max buses is 255
then there can be up to a 8 second delay to search the entire PCI space.
Board configs that know thier max bus can limit this search space.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2273 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
on a SOM-DB2301 baseboard with a SOM-2354 cpu module.
- Also does a slight tweak to the ram test code to make it more
obvious when it fails.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2231 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- some ts5300 code. Let's push this upstream for now.
- fix a typo in device.c
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2211 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
vsa on geode GX.
There was some bug in setting up stack, what was that?
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2208 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
other fixes for gx2 ram init.
support for sharplfg00l04 -- not working yet.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2197 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
This is just a skeleton, basically, and will most likely not even
compile yet.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2164 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
disable agp slot in config.lb
fix error in setting up com1 == should be TTYS0_BAUD
note that the uart8250 struct is a bad design, but so is the
uart8250 code.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2161 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
store every HT device unit id base and pass those info to acpi
https://openbios.org/roundup/linuxbios/issue46
Note: This version drops the two scripts a and c and creates the dsdt on
the fly from Config.lb using makerule
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2134 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
to fail later than before.
dos2unix'ed the xe7501devkit files, that might have caused some problems
before.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2127 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Special version for HDAMA rev G with 33Mhz test and reboot out.
- Support for CPU rev E, dual core, memory hoisting,
- corrected an SST flashing problem. Kernel bug work around (NUMA)
- added a Kernel bug work around for assigning CPU's to memory.
r2@gog: svnadmin | 2005-08-03 08:47:54 -0600
Create local LNXI branch
r1110@gog: jschildt | 2005-08-09 10:35:51 -0600
- Merge from Tom Zimmerman's additions to the hdama code for dual core
and 33Mhz fix.
r1111@gog: jschildt | 2005-08-09 11:07:11 -0600
Stable Release tag for HDAMA-1.1.8.10 and HDAMA-1.1.8.10LANL
r1112@gog: jschildt | 2005-08-09 15:09:32 -0600
- temporarily removing hdama tag to update to public repository. Will
reset tag after update.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@2004 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
1. x86_setup_mtrr take address bit.
2. generic ht, pcix, pcie beidge...
3. scan bus and reset_bus
4. ht read ctrl to decide if the ht chain
is ready
5. Intel e7520 and e7525 support
6. new ich5r support
7. intel sb 6300 support.
yhlu patch
1. split x86_setup_mtrrs to fixed and var
2. if (resource->flags & IORESOURCE_FIXED ) return; in device.c pick_largest_resource
3. in_conherent.c K8_SCAN_PCI_BUS
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1982 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Creator: Yinghai Lu <yhlu@tyan.com>
add eswar code in intel car to disable Hyperthreading
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1980 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Creator: Yinghai Lu <yhlu@tyan.com>
write_pirq_routing_table for x86
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1979 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Creator: Li-Ta Lo <ollie@lanl.gov>
More Via EPIA
more via epia stuff, including the trival but fatal bug in auto.c
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1978 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Creator: Li-Ta Lo <ollie@lanl.gov>
S4880 mainboard Config.lb
Comment in the Config.lb shoud be '#' rather than the C++ '//'.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1977 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Creator: Li-Ta Lo <ollie@lanl.gov>
auto.c and failover.c
convert mainboard auto.c and failover.c to post DOM era
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1976 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Creator: Yinghai Lu <yhlu@tyan.com>
more safe stack in ram for cache_as_ram
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1969 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Creator: Yinghai Lu <yhlu@tyan.com>
cache_as_ram for AMD and some intel
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1967 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Creator: Ronald G. Minnich <rminnich@lanl.gov>
This now boots to the point of passing the memory test in auto.c. But: we still don't have it working after the "Jumping to LinuxBIOS" step
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1966 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Creator: Ronald G. Minnich <rminnich@lanl.gov>
this is a version that does not fail, but memory is still not up
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1965 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Creator: Ronald G. Minnich <rminnich@lanl.gov>
sc520 fails after NOP
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1962 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Creator: Li-Ta Lo <ollie@lanl.gov>
Onboard VGA for HDAMA
Added onboard VGA support for Arima/HDAMA
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1957 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Creator: Li-Ta Lo <ollie@lanl.gov>
ibm e325
Bring imb e325 to post device object model era
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1956 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Creator: Li-Ta Lo <ollie@lanl.gov>
emulator update
x96emu update from Paulo
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1954 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Creator: Li-Ta Lo <ollie@lanl.gov>
emulator update
Correction to the reduce emulator from Paulo
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1952 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Creator: Yinghai Lu <yhlu@tyan.com>
AMD D0/E0 Opteron new mem mapping support, AMD E Opteron mem hole support,AMD K8 Four Ranks DIMM support
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1950 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Creator: Hamish Guthrie <hamish@prodigi.ch>
Added NSC pc97317 super-io and added fill character option to config/Options.lb to speed up flash programming
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1945 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Creator: Hamish Guthrie <hamish@prodigi.ch>
Adds a tree for the Eaglelion mainboard. This board has an AMD GX1 processor in a typical Mini-ATX format with a few ISA and PCI slots.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1941 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Creator: Yinghai Lu <yhlu@tyan.com>
AMD MB IDE enable in Config.lb
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1940 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Creator: Ronald G. Minnich <rminnich@lanl.gov>
add in stepan's raminit code for the sc520
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1939 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Creator: Ronald G. Minnich <rminnich@lanl.gov>
add console options to via/epia/Options.lb
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1932 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Creator: Yinghai Lu <yhlu@tyan.com>
ide_enable in MB Config and jmp_auto ( it will make start in the 64k boundary)
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1926 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Creator: Stefan Reinauer <stepan@openbios.org>
fix dram initialization on island/aruma
Never trust the specs. :-) I messed the different
cpu numbering notations up before. This makes my
wrong 8x patch obsolete as well.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1925 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
* create vital ACPI information from the linuxbios device tree.
* pass linuxbios information into dsdt.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1911 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- The sandpointx3+altimus has been consolidated into one directory for now.
- Added support for having different versions of the pci access functions
on a per bus basis if needed.
Hopefully I have not broken something inadvertently.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1786 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- optimize_link_read_pointers compiles now on the solo so don't disable it.
- Start sorting out the confusion between and object and an initobject on the ppc ports
- Major bugfix release of romcc to support to remove preprocessor deficiencies.
The line and column numbers are computed are now correct. But watch out
the error messages sometimes report the location of the next token so things
are still a little skewed.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1784 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Set adl855pc ROM_SIZE to 1M
Other minor debug prints until we get this fixed.
We're almost as far along as we were before the Change :-)
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1780 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
crt0.S.lb: Modified so that it is safe to include console.inc
console.c: Added print_debug_ and frieds which are non inline variants of the normal console functions
div64.h: Only include limits.h if ULONG_MAX is not defined and define ULONG_MAX on ppc
socket_754/Config.lb Conditionally set config chip.h
socket_940.c We don't need and #if CONFIG_CHIP_NAME we won't be linked in if there are no references.
slot_2/chip.h: The operations struct need to be spelled cpu_intelt_slot_2_ops
slot_2/slot2.c: The same spelling fix
socket_mPGA603/chip.h: again
socket_mPGA603/socket_mPGA603_400Mhz.c: and again
socket_mPGA604_533Mhz/Config.lb: Conditionally defing CONFIG_CHIP_NAME
socket_mPGA604_800Mhz/chip.h: Another spelling fix
socket_mPGA604_800Mhz.c and again
via/model_centaur/model_centaur_init.c: It's not an intel CPU so don't worry about Intel microcode uptdates
earlymtrr.c: Remove work around for older versions of romcc
pci_ids.h: More ids.
malloc.c: We don't need string.h any longer
uart8250.c: Be consistent when delcaring functions static inline
arima/hdama/mptable.c: Cleanup to be a little more consistent
amdk8/coherent_ht.c:
- Talk about nodes not cpus (In preparation for dual cores)
- Remove clear_temp_row (as it is no longer needed)
- Demoted the failure messages to spew.
- Modified to gracefully handle failure (It should work now if cpus are removed)
- Handle the non-SMP case in verify_mp_capabilities
- Add clear_dead_routes which replaces clear_temp_row and does more
- Reorganize setup_coherent_ht_domain to cleanly handle failure.
- incoherent_ht.c: Clean up the indenation a little.
i8259.c: remove blank lines at the start of the file.
keyboard.c: Make pc_keyboard_init static
ramtest.c: Add a print out limiter, and cleanup the printout a little.
amd8111/Config.lb: Mention amd8111_smbus.c
amd8111_usb.c: Call the structure usb_ops not smbus_ops.
NSC/pc97307/chip.h: Fix spelling issue
pc97307/superio.c: Use &ops no &pnp_ops.
w83627hf/suerio.c: ditto
w83627thf/suerio.c: ditto
buildrom.c: Use braces around the body of a for loop. It's more maintainable.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1778 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The static device tree is not built properly at all yet, but at least we get through it.
FIXME (What is the proper way to handle add in boards?)
- Add generic div64 support and ppc div64 support
- Fix abuild so it properly generates the CC line when cross compiling.
- Add one more possible ppc cross compiler target
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1762 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Move pci_set_method out of hardwaremain.c
- Re-add debugging name field but only include the CONFIG_CHIP_NAME is
enabled. All instances are now wrapped in CHIP_NAME
- Many minor cleanups so most ports build.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1737 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
ram linuxbios_ram instead of linuxbios_c and linuxbios_payload...
- Reordered the linker sections so the LinuxBIOS fallback image can take more the 64KiB on x86
- ROM_IMAGE_SIZE now will work when it is specified as larger than 64KiB.
- Tweaked the reset16.inc and reset16.lds to move the sanity check to see if everything will work.
- Start using romcc's built in preprocessor (This will simplify header compiler checks)
- Add helper functions for examining all of the resources
- Remove debug strings from chip.h
- Add llshell to src/arch/i386/llshell (Sometime later I can try it...)
- Add the ability to catch exceptions on x86
- Add gdb_stub support to x86
- Removed old cpu options
- Added an option so we can detect movnti support
- Remove some duplicate definitions from pci_ids.h
- Remove the 64bit resource code in amdk8/northbridge.c in preparation for making it generic
- Minor romcc bug fixes
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1727 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- mem.h and sizeram.h and all includes killed because the are no longer needed.
- linuxbios_table.c updated to directly look at the device tree for occupied memory areas.
- first very incomplete stab a converting the ppc code to work with the dynamic device tree
- Ignore resources before we have read them from devices, (if the device is disabled ignore it's resources).
- First stab at Pentium-M support
- add part/init_timer.h making init_timer conditional until there is a better way of handling it.
- Converted all of the x86 sizeram to northbridge set_resources functions.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1722 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
the time source. The apic timer also has a variable time base.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1711 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Rename chip_config chip_operations throughout the tree
- Fix Config.lb on most of the Opteron Ports
- Fix the amd 8000 chipset support for setting the subsystem vendor and device ids
- Add detection of devices that are on the motherboard (i.e. In Config.lb)
- Baby step in getting the resource limit handling correct, Ignore fixed resources
- Only call enable_childrens_resources on devices we know will have children
For some busses like i2c it is non-sense and we don't want it.
- Set the resource limits for pnp devices resources.
- Improve the resource size detection for pnp devices.
- Added a configuration register to amd8111_ide.c so we can enable/disable individual ide channels
- Added a header file to hold the prototype of isa_dma_init
- Fixed most of the superio chips so the should work now, the via superio pci device is the exception.
- The code compiles and runs so it is time for me to go to bed.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1698 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Fix the hdama Config.lb to not longer use the link keywords oops,
and instead to have it nest everything properly.
- Update config.g to not support the link keyword
- update config.g to not support northbridge/southbridge/cpu/pmc noise words
we can just use chip now.
- Remove old link handling from the code
- Detect and handle duplicate paths so we generate one device with multiple links
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1685 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Rename sdram_init to memory_init
NOTE: need to test sandpoint and ep boards!
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1603 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Updated the romcc version in Config.lb
- Fixed type sizes in romcc_io.h and io.h inl() returning a byte was nasty
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1583 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Although it is not used currently, misuse of terminolog is still a misuse.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1548 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
not actually defined in the mainboard.c. It was only declared in chip.h. Why gcc did not tell
me this mistake and why gcc does not complain about define a structure twice ?
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1539 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
cleanups. Drop "driver" code from mainboard directories and use them from the
driver directory instead
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1534 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Unified AMD K8 reset function that can be customized via mainboard Config.lb
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1471 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
on all amd64 motherboards, so it moved to the amdk8 specific code.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1470 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Reworked pnp superio device support. Now complete superio support is less than 100 lines.
- Added support for hard coding resource assignments in Config.lb
- Minor bug fixes to romcc
- Initial support for catching the x86 processor BIST error codes. I've only seen
this trigger once in production during a very suspcious reset but...
- added raminit_test to test the code paths in raminit.c for the Opteron
- Removed the IORESOURCE_SET bit and added IORESOURCE_ASSIGNED and IORESOURCE_STORED
so we can tell what we have really done.
- Added generic AGP/IOMMU setting code to x86
- Added an implementation of memmove and removed reserved identifiers from memcpy
- Added minimal support for booting on pre b3 stepping K8 cores
- Moved the checksum on amd8111 boards because our default location was on top of
extended RTC registers
- On the Hdama added support for enabling i2c hub so we can get at the temperature
sensors. Not that i2c bus was implemented well enough to make that useful.
- Redid the Opteron port so we should only need one reset and most of memory initialization
is done in cpu_fixup. This is much, much faster.
- Attempted to make the VGA IO region assigment work. The code seems to work now...
- Redid the error handling in amdk8/raminit.c to distinguish between a bad value
and a smbus error, and moved memory clearing out to cpufixup.
- Removed CONFIG_KEYBOARD as it was useless. See pc87360/superio.c for how to
setup a legacy keyboard properly.
- Reworked the register values for standard hardware, moving the defintions from
chip.h into the headers of the initialization routines. This is much saner
and is actually implemented.
- Made the hdama port an under clockers BIOS. I debuged so many interesting problems.
- On amd8111_lpc added setup of architectural/legacy hardware
- Enabled PCI error reporting as much as possible.
- Enhanded build_opt_tbl to generate a header of the cmos option locations so
that romcc compiled code can query the cmos options.
- In romcc gracefully handle function names that degenerate into function pointers
- Bumped the version to 1.1.6 as we are getting closer to 2.0
TODO finish optimizing the HT links of non dual boards
TODO make all Opteron board work again
TODO convert all superio devices to use the new helpers
TODO convert the via/epia to freebios2 conventions
TODO cpu fixup/setup by cpu type
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1390 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Support for compiling romcc on non x86 platforms
- new romc options -msse and -mmmx for specifying extra registers to use
- Bug fixes to device the device disable/enable framework and an amd8111 implementation
- Move the link specification to the chip specification instead of the path
- Allow specifying devices with internal bridges.
- Initial via epia support
- Opteron errata fixes
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1200 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
But linux still refuses to believe this table. What's odd is this is the identical table used in V1. Damn.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1173 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
buildtarget now takes either a directory, and uses directory/Config.lb, or
takes a file
epia defaults to 256k flash
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1166 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Major restructuring of hypertransport handling.
Major rewerite of superio/NSC/pc87360 as a proof of concept for handling superio resources dynamically
Updates to hard_reset handling when resetting because of the need to change hypertransport link
speeds and widths.
(a) No longer assume the boot is good just because we get to a hard reset point.
(b) Set a flag to indicate that the BIOS triggered the reset so we don't decrement the
boot counter.
Updates to arima/hdama mptable so it tracks the new bus numbers
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1097 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
* subtractive resources
* merging with the static device tree
* more device types than just pci
- The piece to watch out for is the new enable_resources method that was needed in all of the drivers
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1096 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
for paths
- Renamed some configuration variables
SMP -> CONFIG_SMP
MAX_CPUS -> CONFIG_MAX_CPUS
MAX_PHYSICAL_CPUS -> CONFIG_MAX_PHYSICAL_CPUS
- Removed some dead configuration variables
MAX_CPUS -> CONFIG_MAX_CPUS
MAX_PHYSICAL_CPUS -> CONFIG_MAX_PHYSICAL_CPUS
SMP -> CONFIG_SMP
FINAL_MAINBOARD_FIXUP
SIO_BASE
SIO_SYSTEM_CLK_INPUT
NO_KEYBOARD
USE_NORMAL_IMAGE
SERIAL_CONSOLE
USE_ELF_BOOT
ENABLE_FIXED_AND_VARIABLE_MTRRS
START_CPU_SEG
DISABLE_WATCHDOG
ENABLE_IOMMU
AMD8111_DEV
- Removed some assembly files that are no longer needed
killed src/southbridge/amd/amd8111/smbus.inc
killed src/southbrideg/amd/amd8111/cmos_boot_failover.inc
killed src/ram/ramtest.inc
- Updates to config.g so that it works more reliably and has initial support
for paths
- Renamed some configuration variables
SMP -> CONFIG_SMP
MAX_CPUS -> CONFIG_MAX_CPUS
MAX_PHYSICAL_CPUS -> CONFIG_MAX_PHYSICAL_CPUS
- Removed some dead configuration variables
MAX_CPUS -> CONFIG_MAX_CPUS
MAX_PHYSICAL_CPUS -> CONFIG_MAX_PHYSICAL_CPUS
SMP -> CONFIG_SMP
FINAL_MAINBOARD_FIXUP
SIO_BASE
SIO_SYSTEM_CLK_INPUT
NO_KEYBOARD
USE_NORMAL_IMAGE
SERIAL_CONSOLE
USE_ELF_BOOT
ENABLE_FIXED_AND_VARIABLE_MTRRS
START_CPU_SEG
DISABLE_WATCHDOG
ENABLE_IOMMU
AMD8111_DEV
- Removed some assembly files that are no longer needed
killed src/southbridge/amd/amd8111/smbus.inc
killed src/southbrideg/amd/amd8111/cmos_boot_failover.inc
killed src/ram/ramtest.inc
killed src/sdram/generic_dump_spd.inc
killed src/sdram/generic_dump_spd.inc
- Updated the arima/hdama to build with the new configuration system
- Updated config.g to list all of the variables with make echo
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1093 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Moving tyan resource map to tyan directory. Making IOMMU for hammer choosable
via ENABLE_IOMMU
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1088 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
cpu of a certain type and to eliminate the
cpu p5
cpu p6
cpu k7
nonsense in the old config files.
Next step is to hook into Eric's pci device stuff.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1067 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Bump up debugging messages and reduce the size of memory test until that is
running correctly.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@1035 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- SMP cleanups (remove SMP only use CONFIG_SMP)
- Minor tweaks to romcc to keep it from taking forever compiling
- failover fixes
- Get a good implementation of k8_cpufixup and sizeram for the opteron
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@998 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
* remove dead code from coherent_ht.c
* add ldtstop code for link speed changes
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@991 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Changes to allow more code to be compiled both ways
- Working SMP support
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@987 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Remove some debugging code from auto.c
- Update coeherent_ht.c so we get the proper broadcast routes.
- Fix the dram probing code.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@973 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Add initial support for the amd8131
- Update the mptable to something possible
- hdama/Config add the amd8131 southbridge
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@968 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- romcc_io.h Add include guards.
- hdama/Config nothing really but I have been moving the setting back and forth between 1 and 2 cpus
- auto.c Changed the enabled debugging comments. This almost works with 2 cpus
- coherent_ht.c First pass at getting this right. It can now find 2 cpus and place them
in some semblance of a working state.
- raminit.c Fix problems with 4GB of ram. Disable some of the debugging code.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@965 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
I set USE_FALLBACK_IMAGE to 1 in the top-level Config, but when it is tested
in arima/hdama/Config.lb, it is acting as though it is zero.
Also added a print command so it is easier to trace 'if' behavior.
Usage:
print "string"
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@913 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
more fixes to various Config.lb
one last problem and we're there
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@911 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Add an additional consistency check to romcc and fix the more obvious problems it has uncovered
With this update there are no known silent failures in romcc.
- Update the memory initialization code to setup all 3 of the memory sizing registers properly
- In auto.c test our dynamic maximum amount of ram.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@885 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Minor romcc fixes
- In smbus_wail_until_done a romcc glitch with || in romcc where it likes
to run out of registers. Use | to be explicit that I don't need the short
circuiting behavior.
- Remove unused #defines from coherent_ht.c
- Update the test in auto.c to 512M
- Add definition of log2 to romcc_io.h
- Implement SPD memory sizing in raminit.c
- Reduce the number of memory devices back 2 to for the SOLO board.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@883 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Update apic.h to include the APIC_TASK_PRI register definition
- Update mptable.c to have a reasonable board OEM and productid
- Additional testfiles for romcc.
- Split out auto.c and early failover.c moving their generic bits elsewere
- Enable cache of the rom
- Fixes to amd8111_lpc.c so that we successfully setup virtual wire mode on the ioapic
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@880 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
The goal is to have the same interface with or without romcc.
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@868 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
- Implementation of fallback/normal support for the amd solo board
- Minor bugfix in romcc
git-svn-id: svn://svn.coreboot.org/coreboot/trunk@867 2b7e53f0-3cfb-0310-b3e9-8179ed1497e1
Uwe Hermann